Power packs AXIOM computerised series A. Mains supply wiring [Applicable to Axiom/Commander 10 terminal versions] White Axiom 18/36/58 W Axiom 18/36/58 W Grey (Cut & terminate) AC & EM Lamp 18, 36 or 58 W EM Lamp 18, 36 or 58 W AC Lamp 18, 36 or 58 W AC Lamp 18, 36 or 58 W Axiom 18/36/58 W White Axiom 18/36/58 W AC & EM Lamp 18, 36 or 58 W EM Lamp 18, 36 or 58 W 36W WIRE PREPARATION AC Lamp 18 W Axiom 18 W Wires approx ≤ 1m from power pack ANTENNA PREPARATION (AXIOM FITTINGS ONLY) AC & EM Lamp 18 W 204449 - (01.09.08) 204449 (18.11.11) The Axiom fittings antenna must be orientated in the vertical position B. Mains supply wiring [Applicable to Axiom/Commander 10 terminal versions] * ** * 10 9 MAINTAINED (1 x Electronic Ballast, 1 x Tube) Ballast Type: Tridonic.Atco PC 1/18, PC1/36, PC1/58 T8 PRO AC+EM tube 12 11 ** 4 3 UL L (Live) SINGLE TUBE ELECTRONIC BALLAST TRIDONIC.ATCO PC 1/18 T8 PRO (Art No 22176005) PC 1/36 T8 PRO (Art No 22176108) PC 1/58 T8 PRO (Art No 22176007) N (NEUTRAL) Mains Terminal Block in the Enclosure EM1 AC LAMP SENSOR WIRES ** ** & * * 1m long maximum EM2 LEGRAND POWER PACK - AXIOM 18/36/58W Contact position shown when Mains is on * ** 6 * ** 3 5 AC tube 7 MAINTAINED (1 x Electronic Ballast, 2 x Tubes) Ballast Type: VS-ELXc 236.202 2x18W or 2x36W 1 2 AC+EM tube UL L (Live) DOUBLE TUBE ELECTRONIC BALLAST VS-ELXc 236.202 (Ref No 188316) N (NEUTRAL) Mains Terminal Block in the Enclosure EM1 AC LAMP SENSOR WIRES ** ** & * * 1m long maximum EM2 LEGRAND POWER PACK - AXIOM 18 or 36W Contact position shown when Mains is on * ** * ** 3 14 13 12 AC tube 11 10 9 MAINTAINED (1 x Electronic Ballast, 2 x Tubes) Ballast Type: Tridonic.Atco PC 2/18, PC2/36, PC2/58 T8 PRO AC+EM tube 4 UL L (Live) N (NEUTRAL) Mains Terminal Block in the Enclosure EM1 ** ** & * * 1m long maximum AC LAMP SENSOR WIRES LEGRAND POWER PACK - AXIOM 18/36/58W Contact position shown when Mains is on 204449 - (01.09.08) 204449 (18.11.11) EM2 DOUBLE TUBE ELECTRONIC BALLAST TRIDONIC.ATCO PC 2/18 T8 PRO (Art No 22176008) PC 2/36 T8 PRO (Art No 22176009) PC 2/58 T8 PRO (Art No 22176010) C. Mains supply wiring [Applicable to Axiom/Commander 10 terminal versions] MAINTAINED (1 x Electronic Ballast, 1 x Tube) * 10 * ** 9 Ballast Type: Tridonic.Atco PC 1/14-21-28-35 T5 PRO LP AC+EM tube 11 12 ** 3 4 UL 2 L (Live) N (NEUTRAL) SINGLE TUBE ELECTRONIC BALLAST TRIDONIC.ATCO PC 1/14-21-28-35W T5 PRO LP Art No 22176096 E (Earth) EM1 Mains Terminal Block AC LAMP SENSOR WIRES in the Enclosure EM2 LEGRAND POWER PACK - AXIOM 14/21/28/35W ** ** & * * 1m long maximum Contact position shown when Mains is on MAINTAINED (1 x Electronic Ballast, 2 x Tubes) * ** * ** AC tube 3 AC+EM tube 4 * * * 4 * 3 4 UL 3 9 10 11 12 13 14 15 16 Ballast Type: Tridonic.Atco PC 2/14-21-28-35W T5 PRO LP 2 L (Live) DOUBLE TUBE ELECTRONIC BALLAST TRIDONIC.ATCO PC 2/14-21-28-35W T5 PRO LP Art No 22176097 N (NEUTRAL) E (Earth) Mains Terminal Block in the Enclosure ** ** & * * 1m long maximum 3 * 3* & 4* 4* EM1 AC LAMP SENSOR WIRES EM2 LEGRAND POWER PACK - AXIOM 14/21/28/35W Contact position shown when Mains is on 1 2 UNSWITCHED LIVE NEUTRAL TERMINAL BLOCK CONFIGURATION 3 4 5 6 7 8 9 10 EM1 Contacts closed as shown when mains applied to 1 & 2. Contacts open at mains failure with 4 & 10 connecting to emergency output voltage EM2 WIRE PREPARATION The battery pack must be connected to the control pack using only the wires and connectors provided. 105 C 0.8 - 1.35mm Switched and unswitched lives (active) must be connected on the same phase. If the emergency lamp comes on when the switched live is turned off, check that the wiring to the control pack is correct and the switched and unswitched lives are correclty connected. Fluorescent lamp: - Wires approx ≤ 1m from power pack ANTENNA PREPARATION (AXIOM FITTINGS ONLY) The Axiom fittings antenna must be orientated in the vertical position 204449 - (01.09.08) 204449 (18.11.11) 8-9 mm Product Notice Notice Important Notice Important Notice Legrand Australia Pty Ltd recommends and advises that only licensed and qualified electricians undertake installation and maintenance of this emergency Legrand Australia Pty Ltdcomplies recommends and advises that only suitably qualified undertake installation and maintenance of lighting unit. And installation with relevant safety and electrical standards and it is personnel carried out in a tradesman like manner. this emergency lighting unit, and that the installation complies with relevant safety and electrical standards. Standard (variable-rate charge) Red LED: (Indicates charging stateRange of the battery) Standard - Premium Installation Testing LED On: Unitunswitched on variable rate charge. - with the unit connected to the mains supply, check that the red charge indicator is illuminated. If not illuminated check that the supply is on, and that the battery leads in the unitorare correctly connected. It is recommended that the LED Off: Indicates loss of 240V a.c. Power, battery disconnection (IEC models) for a minimum of 16 hours before full discharge is performed. checking of the emergency lamp batteries be charged some aincandescent unitstest extinguish red LED However, if an emergency lamp fails. function may be performed after 1 hour by momentarily pressing thewhen test unit switch on the Red LED is also off is under test.unit. Where a Test Switch is not visible, the luminaire has a Magnetic Test Switch that may be activated by holding any magnet near the Premium Range (dual-rate charge) label marked "Magnetic Switch". Green LED: (Indicates charging state of the battery) Interrupting supply LED Flashing slowly Emergency Lighting (onebatteries. second On,If one second Off), Unit on high ratepermanent charge. damage to the batteries remains interrupted, will discharge supply may result. Do not subject units to a high number of charge/discharge cycles as can occur on temporary (construction) power supply. LED On: Fully charged; trickle charge mode. LED Off: Indicates loss of 240V a.c. Power, or battery disconnection (IEC models) some incandescent units extinguish green LED if an emergency lamp fails. Premium Range (dual-rate charging) Green LED is also off when unit is under test. Red LED: Indicates charging state of the battery Constantly on: Fully charged;Range now on trickle charge. AXIOM/Commander (dual-rate charge) Off: Indicates loss of 230v AC power, or battery disconnection (IEC models) Red LED: (Indicates charging of the battery) some state incandescent units extinguish red LED if an emergency lamp fails. is under test. LED Flashing slowly: Red LED is also off when unit (one second On, one second Off), Unit on high rate charge. Flashing LED On: Fully charged; trickle charge mode (one sec on/off): Unit on high rate charge. LED Off: Indicates loss of 240V a.c Power, or battery disconnection (IEC models) incandescent units extinguish red LED if an emergency lamp fails. Red LED is also off when unit is under test. AXIOM Range (in addition to the Standard-Premium range installation) Green LED: (Indicates communication status) Green LED: LED Flashing rapidly: indicates communication status. Self testing has found a fault within the unit. (Red LED also flashes rapidly). Off: Communication is correct (except for short flash when the SPU is addressed Green LED can also be made to flash rapidly by System commands. by the computer). LED (one second On, one second Off), unit yet to be commissioned. On:Flashing slowly: Self testing has found a fault within the unit. Flashing LED Off: Communication is correct (except for short flash when the SPU is addressed by the computer). (one sec on/off): unit yet to be commissioned. Antenna Installation – In all Axiom fittings (except weatherproof battens), the antenna must be orientated in the vertical position. Installation – with unittoconnected the unswitched mains supply, check that the red charge indicator (or green depending on the charging Green LEDTesting can also be the made flash bytosystem commands. mechanism) is illuminated. If not illuminated check that the supply is on, and that the battery leads in the unit are correctly connected. It is recommended that the batteries charged for a minimum of 16 hours before a full discharge testAS/NZS2293 is performed. However, checking the emergency lamp function and may Inspection andbeMaintenance - must be performed in accordance with for Australian andofNew Zealand installations be afterwith 1 hour by momentarily pressingintheother test switch on the unit. accordance relevant local standards countries. in performed Where a Test Switch is not visible, the luminaire has a Magnetic Test Switch that may be activated by holding a magnet near the label marked “Magnetic TheSwitch”. batteries in this emergency lighting unit MUST be replaced when the unit no longer meets rated operating life. Test Interrupting supply will Discharge Emergency Lighting Batteries. If supply remains interrupted for long period, permanent damage to the batteries may Warranty - Legrand Australia Pty Ltd guarantees this emergency lighting unit for a period of 12 months from date of despatch, solely result due to excessive battery discharge. Do not subject units to a high number of charge/discharge cycles as can occur on temporary (construction) against failure arising from faulty materials or workmanship, and provided that the unit has been stored, shipped, installed, used and power supply. maintained in accordance with the manufacturers instructions and relevant standards. Misuse, negligence or modification of the unit Inspection and Maintenance must be performed accordance with AS/NZS2293-2 Australian and New Zealand voids all warranties. Consult– Legrand AustraliainPty Ltd “Conditions of Sale” forfor details on warranty liability. installations and in accordance with relevant local standards in other countries. If this emergency lighting unit is faulty, returnbethe unit freight pre-paid yourmeets point rated of purchase, The batteries in this emergency lighting unit MUST replaced when the unit notolonger operating or life.contact Legrand Australia Pty Ltd on (61) 2 8748 0300. Warranty – Legrand Australia Pty Ltd guarantees this emergency lighting unit for a period of 12 months from date of despatch, solely against failure arising from faulty materials or workmanship, and provided that the unit has been stored, shipped, installed, used and maintained in accordance with the Technical Data - for full technical or photometric data please consult Legrand Australia Pty Ltd. manufacturers instructions and relevant standards. Misuse, negligence or modification of the unit voids all warranties. Consult Legrand Australia Pty Ltd Conditions of Sale for details on warranty liability. Disclaimer - the information and advice given should be taken as a guide only. Both are given in good faith, and are true and correct Iftothis lighting unit is faulty, return unit freightofpre-paid to your point ofand purchase, or contact Legrand Australia Pty Ltd onshould (+61 2)determine 8719 theemergency best of our knowledge, though nothe guarantee accuracy is given, thus persons receiving this information 4333. its suitability. Technical Data – for additional technical data please contact Legrand Technical Support Centre on (AU) 1300 369 777 or (+61 2) 8719. 4333 – (NZ) 0800 476 009 or (+64 9) 442 0800 Disclaimer – the information and advice given in this document should be taken as a guide only. Both are given in good faith and are true to the best of our knowledge, though no guarantee of accuracy is Legrand Australia Pty Ltd given, and thus persons receiving this information should determine its suitability. Wiring diagrams in this ABN 41 000 565 739 document do not imply compliance with Australian Standards for the completed fitting. Compliance to 79-99 Hilliers Road the relevant requirements of Australian electrical safety standards AS/NZS60598, emergency lighting Aubrun NSW 2144 standards AS2293 and EMC regulations are the responsibility of the manufacturer of the final fitting. Australia 204449 – (18.07.06) 204449 (18.11.11) Tel: (02) 8748 8748 0300 0333 Fax: 0345 Fax: (02) 8748 9737 8211 www.legrand.com.au