LEP50H Instruction
a member of Aztech Group
Specifications
Operating Input Voltage
Power Charging Time
Battery Charging Current
Battery Discharge Time
Battery Discharge Current
Supply Current
Output Voltage
Protection System
Mains Voltage Change Over Threshold
Operating Temperature
220 - 240 Vac, 50 - 60Hz
<10Hrs (4.8V/2200mAh Battery Pack)
550mA
>2Hrs (4.8V/2200mAh Battery Pack)
700mA at 4.8Vdc (Typical)
90mA - 120mA *
6Vdc (Open Circuit Voltage at AC Mode)
105Vdc (Battery Mode)
Low voltage cut-off
Isolated Battery Charging Supply Voltage
Constant battery status monitoring
Basic Insulation
According to EN 60598-2-22
20 to 50 °C
> 2Hrs Battery Discharge
<20°C
> 1Hr Battery Discharge
AWG 18-22 0.327 to 0.789mm²
209mm (L) X 39mm (W) X 28mm (H)
Wire Preparation/Cross Section
Dimension
* at 230Vac/50Hz T8 tube and battery connected
Battery Pack
Technology of Battery
Type Designation
Capacity
Voltage
Maximum Charge Current
Minimum Charge Current
Charge Voltage Limits
Maximum Discharge Current
Minimum Discharge Current
Discharge Voltage Limits
Temperature Rating
Type and Manufacturer
Rechargeable
NiMH
2200 mAh
4.8V Typical
0.25C
0.005C
5.8V Max
0.3C
0.1C
3.2V Min
0 ~ 50 deg C
GP 220SCHT
Switching Behavior
L
(Unswitched)
ON
ON
OFF
L1
(Switched)
OFF
ON
Don’t Care
Ballast Lumen
Battery Operation
Factor
0%
Charging if battery is not fully charged
100%
Charging if battery is not fully charged
10%
Battery discharging
LEP50H
Emergency LED Control Gear
Instruction Guide
Product Information
The AZ e-liteTM LEP50H is an emergency LED control gear which adds
emergency lighting functionality to the LT8B-EP T8 tube series when
installed together. All the logic control/monitoring/housekeeping is
done by the LEP50H.
Features and Benefits
Emergency lighting conversion kit support – When paired with AZ-eliteTM
LEP50H Emergency Light conversion kit, LED T8 tube function as an
emergency lighting in Maintained, Non-Maintained or Combine mode.
Ease of maintenance and spare part inventory – One common model of
LED T8 tube for both normal and emergency lighting application. One
common Emergency Lighting conversion kit that support various
lengths of LED T8 tubes (2FT, 4FT and 5FT).
2hrs Rated Duration in Emergency Mode – Meets many countries’
emergency lighting requirements.
10% Emergency Ballast Lumen Factor – Same ballast lumen factor
performance as instead of compare to traditional T8 fluorescent tubes.
Warning:
• Do not use ballast.
• Battery Connection is not Reversible.
• Observe Proper Polarity when Connecting the Battery.
LEP50H Instruction
a member of Aztech Group
Outline Drawing
Wiring Diagram
209
200
AZ e-lite FUSE (250VAC^0.2A) [Optional]
NEUTRAL
SWITCHED LIVE
UNSWITCHED LIVE
MODEL : LEP50H
INPUT : 220-240Vac; 50/60Hz
EMERGENCY LED CONTROL GEAR
BATTERY PACK
(4.8V) 4 CELLS NiMN
CHARGE
Rated Output Voltage: 105VDC
BATTERY CHARGING: 6V; 0.55A
ta: 0-50°C
tc: 70°C Max
Fuse Type: 1A Time Lag Type
Emergency Operation: > 2 Hours
Suitable for operation with LT8B-EP LED Modules Only
DO NOT DO INSULATION TEST ABOVE 500Vdc
BATTERY
WIRE PREPARATION
18-22 AWG
7.5-8.5mm
LED TEST
SWITCH
T
N
L
Battery
Neutral
Charge
LED
+
Test
Switch
S
Unswitched Live
Optional
S
Combine Emergency Lighting
OPTIONAL
AZ e-liteTM FUSE (250VAC/0.2A)
Neutral
Live (220V-240V 50/60Hz)
* Colour of the Solid Circle is Red with a Diameter of at least 10mm
Main Section
+
LED
Lamp
L1 Switched Live
5
LAMP TYPE:
LT8B-418EP-8XX
LT8B-EP LED TUBE
T
39
LED
Neutral
28
Live (220V-240V 50/60Hz)
AZ e-liteTM FUSE (250VAC/0.2A)
LT8B-EP LED TUBE
T
T
N
Battery
Neutral
Charge
LED
+
Test
Switch
S
L1 Switched Live
L
+
LED
Lamp
Unswitched Live
Optional
S
Maintained Emergency Lighting
Control Gear
LED (Green Colour)
Switch
AZ e-liteTM FUSE (250VAC/0.2A)
Neutral
Live (220V-240V 50/60Hz)
Battery Pack
LT8B-EP LED TUBE
T
T
N
Battery
Neutral
Charge
LED
+
Test
Switch
S
L1 Switched Live
L
+
LED
Lamp
Unswitched Live
Non-maintained Emergency Lighting
S
Optional