Product Application Reference
Sensors & Transmitters
S6011-AT Air Conduit Temperature Transmitter
Summary
S6011-AT Air Conduit Temperature Transmitter o er an economical solution for a wide
variety of temperature sensing needs, in the cooling heating, ventilation and air conditioning
Model
S6011-AT/V
S6011-AT/I
Operating voltage
Output signal
0-10V
4-20mA
Measuring range
Measuring accuracy
S6011-AT/VG
S6011-AT/IG
24V DC
0-10V
4-20mA
Temperature -20-50°C
Temperature ±1°C
Ambient temperature
Temperature ±0.5°C
-40-50°C
Storage
-40-50°C, non-condensing
Housing
ABS
Mounting
S6011-AT transmitters can be mounted into air conduit or vent. The gasket ring separates
outside air from transmitter.
Attentions:
Locate the transmitters, where they will be exposed to representative conditions.
Avoid non-representative air draughts, direct sunlight, etc.
S6011-ATH Series of Air Conduit Temperature-Humidity Transmitter
Summary
S6011-ATH
for a wide variety of temperature sensing needs, in the cooling heating, ventilation and air
Model
S6011-ATH/V
S6011-ATH/I
Operating voltage
Output signal
Measuring range
S6011-ATH/VG
S6011-ATH/IG
24V DC
0-10V
4-20mA
0-10V
4-20mA
Temperature -20-50°C
RH 0-100%
Measuring accuracy
Temperature ±1°C
Temperature ±0.5°C
RH ±5% RH
Ambient temperature
RH ±3% RH
-40-50°C
Storage
-40-50°C, non-condensing
Housing
ABS
Mounting
Ordering code
S6011-ATH/X X
G-temperature accuracy±0.5°C
(no alphabet-±1°C)
I- current output 4-20mA
V-voltage output 0-10V
S6011-ATH series of transmitters can be mounted into air conduit or vent. The gasketring
separates outside air from transmitter.
Attentions:
Locate the transmitters, where they will be exposed to representative conditions.
Avoid non-representative air draughts, direct sunlight, etc.
T: Temperature
TH: Temperature and Humidity
24.
CE Compliance EMC (89/336/EEC) according to the standard EN61000-6-1:2001, EN61000-6-3:2001.
Product Application Reference
Transmitters
S6011-RT/RTH series of Temperature Transmitter & Temperature-Humidity Transmitter
Summary
S6011 series of transmitters provide a passive or active signal that corresponds with the air or water
temperature in heating, ventilating and air conditioning applications.
Model No
Operation voltage
Output signal
Measuring range
S6011-RT room temperature transmitter
S6011-RTH room temperature-humidity transmitter
DC 24V
0~10V or 4-20mA
Temperature 0~50°C
Humidity 0~100%RH
Measuring Accuracy
Temperature ±1°C or ±0.5°C
RH ±5%RH or ±3%
Ambient temperature
-20°C~60°C
Storage
-40°C~70°C, non-condensing
Material
ABS
Mounting
The transmitters are suitable for direct wall mounting or ceiling-mounting using four screw holes on the base.
The wiring must be entered from the back. For mounting, follow the instruction below:
Choose an appropriate place to achieve good control of the ambient temperature. The room transmitters
only sense the temperature or humidity at the place where it is mounted.
The transmitters should not be mounted near to windows or doors to avoid draught. On the other hand,
Put insulation material in the wiring conduit to prevent introduction of air from outside the room.
The transmitter should not be exposed to direct radiation or to the sun, as it would lead to incorrect
measurement.
S6011-T Temperature Sensor
Summary
S6011-T temperature sensor is applicable with S2013 series Proportional-plus-integral (PI) controller.
The temperature sensor shall be able to provide with temperature sensor in heating and cooling. When
deviation happens between the ambient temperature and the set point, it is able to provide with temperature
sensor.
Ordering code
Model
Sensing element
Precision
Material
Operation ambient
S6011-T temperature sensor
NTC thermistor
±1°C 10K 25°C
ABS plastics
Temperature -40°C
100°C
RH 10 95%RH non-condensing
+70°C
Storage -40°C
S6011-RXX/X X
G-temperature accuracy±0.5°C
(no alphabet-±1°C)
I- current output 4-20mA
V-voltage output 0-10V
T-temperature;
TH-temperature and humidity
CE Compliance EMC (89/336/EEC) according to the standard EN61000-6-1:2001, EN61000-6-3:2001.
25.
Product Application Reference
Transmitters
S6011-WTX series of Water Pipe Temperature Transmitter
Summary
S6011-WTX series of transmitter is used to measure the liquid temperature in pipes or the air
temperature in heating, ventilating and air conditioning applications. The transmitters provide
0-10V voltage signal or 4-20mA current signal.
Model
S6011-WTA/V
Input voltage
Input signal
Measuring range
Measuring accuracy
Operation temp
Storage
Material
S6011-WTB/I
24V DC
0-10V or 4-20mA
0~50°C
0~100°C
±1°C or ±0.5°C
10~80°C
0~110°C
-40-70°C, non-condensing
poly carbonate
Mounting
To install S6011-WTX, please follow this process: mount casing pipe into pipe and insert the
transmitter into casing pipe and lock it.
Accessory
S6011-WT, Casing pipe (required)
There are two types of casing pipe, 55mm and 115mm.
Ordering code
S6011WT X / X X
A:Precision,siou±0.5℃,±3%　I:4-20MA V:0-10V　A:Temperature :0-50℃　B:T emperature and Humidity
26.
CE Compliance EMC (89/336/EEC) according to the standard EN61000-6-1:2001, EN61000-6-3:2001.