How to make a SP Crystal - ASTRO

advertisement
How to make a SP Crystal
We need for that:
–
A drilling machine with right/left run, best an akku drilling machine. If you don`t have
that crook a wire (bicycle spoke!, see below).
–
Enammeled Copper wire or isolated Copper wire with a diameter of 0.15mm to about
0.8mm and more.For beginners better 0.4 to 0.6mm diameter. Any have problems with
Copper wire, then take better plastic isolated Copper wire (attention maybe PVC!!!,
Aluminium wire works also, but it`s stiffer and difficult to get). I take mostly Copper wire
from 2m lenght.
–
Adhesive tape.
–
A crystal (as clearer as better! Maybe a double ending one).
–
Glue (f.e. Acryl glue).
To make a Moebius coil we must make first a „Moebius wire“.
Usually to make a „M“ coil, see below:
I make other coils to amplify the effect and to enhance the wire resistance, see below:
4 time („M“) coils are simpler to make, they are in the middle only 1 time folded and then
turned. For 6 time or 10 time coils you must make it otherwise. As longer a Moebius coil is
as stronger it becomes, so i take Copper wires with a lenght from 2m (a very small crystal)
to more than 100m (big crystals).
As example i want to make here a 10 time Moebius coil with the lenght of 35m (+
connection about 2x15 cm = 30cm). Have you a plank of about 4m you can hammer in a
nail on the one end of it (maybe without the nailtop, = point A) and more distant of 3.5m
(35:10=3.5)) a second one (= point B). Don`t you have a wood plank, you can take
alternatively f.e. 2 clamps and wind the wire around the handles of the clamps instead
around the nails.
Here i took screws and sticked an adhesive tape over the thread to protect the enammeled
wire. I fixed the begin of the wire with with adhesive tape.
Now to begin at point A, leave about 15cm wire for the connection (make the begin heavy
with anything or fix it with adhesive tape). Then wind a little wire around the nail A, then to
nail B, so long till you count 10 wires between A and B. Then leave about 15cm and cut.
Make also the other end of the wire heavy with anything that it don`t loose.
Also the end of the wire i fixed with adhesive tape and made the lenght right (connection).
Now wind adhesive tape around the wires, after nail A and before nail B, that the wires
keep together and to protect them. Pull carefully the wires over nail A and B, and put
adhesive tapes quite over the begin (10m wires) and the end, as protection. Make you that
without a drilling machine you must not do it.
To replace a drilling machine i crooked a bicycle spoke.
Turn out a screw (B) and add the hook of the bent bicycle spoke there where was the
screw. Then turn it to the right till the wires are nice turned. Attention, that the wires are
always tight.
Fix the begin carefully with the clamp f.e. on a ledge and between a cardboard as
protection. Is a second person present he can hold tight the begin with the hands or pliers
(attention!). Fix the end carefully with adhesive tape as protection into the chuck. Adjust
the drilling machine on left rotation! Distort slowly the wires, keep them alsways tight. Do it
accordingly also with the 6 time coil.
Distort so long till the wire looks so like on the photo above. Then take away the distorted
wire and remove the adhesive tape. Distort also the begin and the end by hand. As safety
check with a continuity tester or an ohmmeter if also electric current goes through. Is that
Ok, you made your „Moebius wire“.
In Internet exist confusion because the clockwise direction: The electrons (atoms), the
earth, galaxies, all what lives, turns clockwise, see picture below:
Thats why the people project the clock f.e. onto a tower or the sky. But we are the clock
ourselves, the head is to the south, the feet are to the nord (best to sleep with the head to
nord and with the feet to south).
Now take the crystal so in the left hand like in the picture below. With the right hand coil
the wire around the crystal.
The SP Crystal is finish. This exemplar here has only 5 turns.
Check again with the ohmmeter..., if going through exists (= coil Ok). Fix the coil with any
glue spots, finish.
It`s very helpful to have a big needle to draw through the distorted wire under the coil (see
above).
3 examples of Moebius coils.
The last one needed more than 50m wire for the coils (10 time, 9cm long crystal) and the
knots turned to 120°, the topmost coil is an Antihaarp Coil, this i explain later.
It`s important the knot is on the square to the wires.
Make it with a lot of love and emotion, so can nothing go wrong.
The SP Crystal (Sucker Punch) sends out Skalarwaves (Longitudinal Waves) and gives
protection and harmony of the energy. Skalarwaves stimulate the healing and are very
good for health. It`s also used to stimulate and activate Orgonit (Polyester resin mixed with
metal dust).
Sandra & Marco Widmer
http://astro-tarot.ch und http://astro-tarot.com
Copyright by Marco Widmer
Download