1/1.5/B/1
Plaster In Grilles
AHP Plaster-in Linear Bar Grille
ADMP Plaster-in Linear Diffuser
ALSP Plaster-in Linear Slot Diffuser
TROX UK Ltd
Caxton Way
Thetford
Norfolk IP24 3SQ
Telephone +44 (0) 1842 754545
Telefax
+44 (0) 1842 763051
e-mail trox@troxuk.co.uk
www.troxuk.co.uk
Contents · Description
Description
AHP Grilles
ADMP Diffusers
AK-AHP & ADMP Plenums
ALSP Linear Slot Diffusers
AK-ALSP Plenum Boxes
Installation Instructions · AK Plenums
Installation Instructions · Blanking Plate
Installation Instructions · Grille / Diffuser
Core Removal & Installation · Type AHP
Core Removal & Installation · Type ADMP
Order Details
Description
Materials
TROX range of plaster in grilles can be used as air terminal
devices for the ventilation of buildings and spaces in terms
of supply air and extract (exhaust) air.
The grilles and linear grilles are manufactured from aluminium
extruded sections. The standard finish is polyester powder
coat to RAL9010:20%. Other standard colours from the RAL
range are available on request.
Type AHP is designed for vertical installation within
walls and bulkheads and provides a horizontal supply air
discharge perpendicular to the mounting surface.
Type ADMP & ALSP are designed for horizontal installation
within ceilings and provide a horizontal supply air discharge
parallel to the mounting surface.
The installation can be carried out directly into a builders
work cut out within a plasterboard wall, with the outer
border providing a surface suitable for plaster skim.
2
2
3
4
5
6
7
Optional ancilleries such as blanking plates and alignment
fixures are finished in RAL9005 (black).
Supply or return air plenums are supplied natural finish,
galvanised steel.
8
9
10
11
12
13
AHP Linear Bar Grilles
Construction · Dimensions · Materials
Type AHP
Materials
The front border is designed to integrate seamlessly within
plasterboard builders work opening, with concealed screw
fix installation. The air discharge can either be at an angle of
0° (AHP-0) or 15° (AHP-15) with fixed horizontal profiled
blades. The central core is removable and provides access
to TROX type AK plenums (if specified).
AHP grille border and blades are manufactured from
aluminium extruded sections. The standard finish is
polyester powder coat to RAL9010:20%.
Optional blanking plates can be provided to cover non-active
grille sections where supply or extract air transfer is not required.
Blanking plates can be requested with optional 6mm foam lining
to provide a thermal insulation between the occupied space and
services void.
Other standard colours from the RAL range are
available on request.
Blanking plates supplied in 1000mm lengths for site cutting and
installation where required. 6mm foam is supplied in 1000mm
lengths for cutting and installation to blanking plates by others.
Optional blanking plates are manufactured from 0.7mm
galvanised steel. The standard finish is polyester powder
coat to RAL9005 (black).
Performance
Refer to product leaflet 1/1.2/B/2 for full technical
performance data.
Type AHP
AHP-0
Front border
Blade
AH-0°
5.5
32,5
AH-15°
WAP-0°
3
20,0
5
12,5
'H' - 4 / 'L' - 4
2,0
'H' - 22,0
3
WAP-15°
Blanking Plate
('L'-4) MIN OPENING SIZE
('L'-16) NECK SIZE
('L'+24) O/A FLANGE
Linear Grilles
SECTION LENGTHS
Grille
Type
'L'
'M'
'E'
Finite
150 - 2400mm
Linear
900 - 1800mm
1800mm
Nominal
'H' Min = 75mm 'H' Max = 200mm
Height
(25mm increments)
('E'-8) O/A NECK (AFTER TRIMMING)
('M') O/A NECK (AFTER TRIMMING)
('E'-8) O/A NECK (AFTER TRIMMING)
('E'+12) REF O/A FLANGE (AFTER TRIMMING)
('M') O/A FLANGE (AFTER TRIMMING)
('E'+12) REF O/A FLANGE (AFTER TRIMMING)
('H' + 24) O/A FLANGE
Finite Grilles
('H' + 24) O/A FLANGE
1000,0
3
ADMP Linear Diffusers
Construction · Dimensions · Materials
Type ADMP
Materials
The front border is designed to integrate seamlessly within
plasterboard builders work opening, with concealed screw fix
installation. The air discharge can either be one or two way
with fixed horizontal profiled blades. The central core is
removable and provides access to TROX type AK plenums (if
specified).
ADMP grille border and blades are manufactured
from aluminium extruded sections. The standard
finish is polyester powder coat to RAL9010:20%.
Optional blanking plates can be provided to cover non-active
grille sections where supply or extract air transfer is not required.
Blanking plates can be requested with optional 6mm foam lining
to provide a thermal insulation between the occupied space and
services void.
Other standard colours from the RAL range are
available on request.
Type ADMP
Performance
Refer to product leaflet 2/2.4/B/1 for full technical
performance data.
Front border
2,0
Blade
22
32,5
'H' - 22,0
20,0
'H' - 4 / 'L' - 4
3.4
ADMP-1
12,5
Blanking plates supplied in 1000mm lengths for site cutting and
installation where required. 6mm foam is supplied in 1000mm
lengths for cutting and installation to blanking plates by others.
Optional blanking plates are manufactured from 0.7mm
galvanised steel. The standard finish is polyester powder
coat to RAL9005 (black).
Blanking Plate
1000,0
Finite Grilles
Grille
Type
Finite
Linear
Nominal
Heights
('L'-4) MIN OPENING SIZE
('L'-16) NECK SIZE
166mm, 203mm
('H' + 24)
O/A FLANGE
('L'+24) O/A FLANGE
SECTION LENGTHS
'L'
'M'
'E'
150 - 2400mm
900 - 1800mm
1800mm
Linear Grilles
4
('E'-8) O/A NECK (AFTER TRIMMING)
('M') O/A NECK (AFTER TRIMMING)
('E'-8) O/A NECK (AFTER TRIMMING)
('E'+12) REF O/A FLANGE (AFTER TRIMMING)
('M') O/A NECK (AFTER TRIMMING)
('E'+12) REF O/A FLANGE (AFTER TRIMMING)
AK-AHP & ADMP Plenum Boxes
Construction · Dimensions · Materials
Type AK-P
Plenum Types
Damper Types
TROX type AK-P plenums boxes can be supplied for supply
air and extract air applications to suit AHP & ADMP finite or
linear grilles.
ZH
AH
ZV
AV
AG
The plenum box is suspended using support wires or
threaded rods (supplied by others), using the drilled holes in
the plenum return edge or hanging brackets when provided.
Horizontal supply
Horizontal extract
Top entry supply
Top entry extract
DG
Opposed blade
action volume control
damper, adjustable via
the front face.
Volume control
damper as ...-AG plus
a set of individually
adjustable vertical air
pattern control blades.
The type AK-P plenum box comprises a casing with
horizontal or vertical circular spigot for duct connection, with
or without opposed blade volume control damper (-AG) or
combined, individually adjustable control blades and opposed
blade volume control damper (-DG).
Materials
Type ZH & ZV plenums come complete with perforated
internal baffles to promote even air distribution with optional
12mm thick black faced, Class 'O' internal lining (... -D)
The plenum box is made from galvanised sheet steel, and is
supplied self-finish. Plenums are manufactured with a 15mm
internally formed flange at each end, with factory fitted foam seal.
AK-P.. ..- ZV / ...-AV
270,0 O/A
148,0 I/S
O/A LENGTH ('L' - 5)
MAX LENGTH ('L' = 2100)
'LN' ACTIVE LENGTH
'H' - 5,0 O/A
'D' DIA SPIGOT
'D' +22
(Min. 'H' +20)
'AG', 'D' or 'DG'
DAMPER (Optional)
FITTED IN PLENUM
32,0
INTERNAL LINING
BELOW BAFFLE TYPE 'A' ONLY
('L' - 35,0)
AK-P.. ..- ZH / ...-AH
O/A LENGTH ('L' - 5)
'D' DIA SPIGOT
1000 Max
'D' + 150,0 Min.
MAX LENGTH ('L' = 2100)
INTERNAL LINING
BELOW BAFFLE TYPE 'A' ONLY
32,0
'AG', 'D' or 'DG'
DAMPER (Optional)
FITTED IN PLENUM
'H' - 5,0 O/A
'LN' ACTIVE LENGTH
('L' - 35,0)
5
ALSP Linear Slot Diffusers
Construction · Dimensions · Materials
Type ALSP
Materials
The front border is designed to integrate seamlessly within
plasterboard builders work opening, with concealed screw
fix installation. The air discharge can either be one or two
way horizontal or vertical with integral baffle plate and
adjustable air control blades.
ALSP grille border and blades are manufactured from
aluminium extruded sections. The standard finish is
polyester powder coat to RAL9010:20%.
Optional blanking plates can be provided to cover non-active
grille sections where supply or extract air transfer is not
required. Blanking plates can be requested with optional
12mm foam lining to provide a thermal insulation between the
occupied space and services void.
Blanking plates supplied in 1800mm lengths for site cutting
and installation where required. 12mm foam is supplied in
1800mm lengths for cutting and installation to blanking
plates by others.
Optional blanking plates are manufactured from 0.7mm
galvanised steel. The standard finish is polyester powder
coat to RAL9005 (black).
Other standard colours from the RAL range are
available on request.
Performance
Refer to TROX Quick Selection Guide or local
TROX Representative for performance data.
Type ALSP
Front border
ALSP-2
25,0
2,0
77,0
OPENING SIZE
'A' + 18
=
=
=
=
=
=
=
=
100 MAX
'A' + 4,0
(O/S)
1800,0
Finite Grilles
('L' + 38,0)
MIN OPENING SIZE
ALSP20-4 Slot
('A' + 51,0)
O/A FLANGE
6
ALSP20-2 Slot
ALSP20-3 Slot
Linear Grilles
('E'+35,5) REF O/A FLANGE (AFTER TRIMMING)
Dimensions
ALSP20-1 Slot
(L+71,0) O/A FLANGE
('E'-8) O/A NECK (AFTER TRIMMING)
Grille
Type
('M') O/A NECK (AFTER TRIMMING)
('M') O/A FLANGE (AFTER TRIMMING)
Grille
Type
Finite
Linear
Grille
Type
Dimensions
80,5
ALSP25-2 Slot
90,5
120,0
ALSP25-3 Slot
135,0
159,5
ALSP25-4 Slot
179,5
'A'
41,0
ALSP25-1 Slot
'A'
46,0
SECTION LENGTHS
'L'
'M'
'E'
600 - 1800mm
900 - 1800mm
1800mm
('E'-8) O/A NECK (AFTER TRIMMING)
('E'+35,5) REF O/A FLANGE (AFTER TRIMMING)
('A' + 51,0) O/A FLANGE
Blanking Plate
AK-ALSP Plenum Boxes
Construction · Dimensions · Materials
Type AK
Plenum Types
Damper Types
TROX type AK plenums boxes can be supplied for supply
air and extract air applications to suit ALSP finite or linear
grilles.
ZH
AH
ZV
AV
M
The plenum box is suspended using support wires or
threaded rods (supplied by others), using the drilled holes in
the plenum return edge or hanging brackets when provided.
The type AK plenum box comprises a casing with
horizontal circular spigot for duct connection, with or without
spigot mounted perforated trimming damper (...-M)
Horizontal supply
Horizontal extract
Top entry supply
Top entry extract
Spigot mounted
perforated steel
trimming damper,
adjustable through front
face (types ...-ZH / AH
only)
Materials
The plenum box is made from galvanised sheet steel, and is
supplied self-finish. Plenums are manufactured with a 15mm
internally formed flange at each end, with factory fitted foam seal.
Optional 12mm thick black faced, Class 'O' internal lining
(... -D) is available on all AKV-ALSP plenums.
AK.. ..- ZH / ...-AH
O/A LENGTH ('L' - 5)
'W' O/S
15,0
('D' + A + 22) O/S REF
'D' DIA SPIGOT
'D' + 22,0
76,0
'W' O/S
'LN' ACTIVE LENGTH
('L' - 35,0)
ALSP20-4 Slot
93,0 'D'+'A'+122
214,0 132,5 'D'+'A'+122
254,0 172,0 'D'+'A'+122
Ø158
ALSP25-2 Slot 214,0 103,0 'D'+'A'+122
Ø198
ALSP25-4 Slot 310,0 192,0 'D'+'A'+122
Ø198
ALSP25-3 Slot 254,0 147,5 'D'+'A'+122
Ø158
Ø198
Ø248
'B' I/S
Multiple Spigots
=
L1 / 2
(200) O/S REF
ALSP20-3 Slot
176,0
Dimensions
Dimensions
Grille
Spig. Ø
Spig. Ø
Type
ZV / AV
ZV / AV
'B'
'W'
'Eb'
'B'
'Eb'
53,5 'D'+'A'+122 Ø123 ALSP25-1 Slot 138,0 58,5 'D'+'A'+122 Ø123
=
=
L1 / 3
L1 / 3
=
=
L1 / 4
L1 / 4
L1 / 4
100,0
ALSP20-2 Slot
'W'
138,0
'D' DIA
SPIGOT
15,0
76,0
Grille
Type
ALSP20-1 Slot
100,0
'B' I/S
EXTENSION 'A'
700,0 Max.
'Eb' O/A HEIGHT
MAX LENGTH ('L' = 2100)
=
7
Installation Instructions
Preparing the plasterboard aperture
Installing TROX AK plenum boxes
Installation of TROX Plaster in Grilles requires an aperture in
the plasterboard to be created large enough for the neck of the
grille to clear.
Provision should be made to suspend the supply or return
air plenum boxes (if specified) behind the plaster board /
timber frame in such a way that no weight from the plenum is
transferred to the grille border.
The minimum opening size for the plasterboard aperture should
be based on the specified grille type and nominal size (refer to
project schedule for unit sizes). Minimum opening sizes
relating to the nominal grille size are detailed on pages 3, 4 & 6
of this technical leaflet.
Behind the plasterboard, a sturdy timber batten frame is to
be provided (by others) to match the opening size within the
plasterboard. The minimum combined construction depth for
plasterbord & batten should be between 40mm up to a
maximum of 60mm.
Each AK plenum box is to be installed using suitable threaded
rod or wire supports (by others) to take the weight of the plenum.
IMPORTANT; To ensure a good seal against the diffuser face,
the edge of the plenum should sit square within the opening
and flush with the unfinished plasterboard face.
Construction
Vertical section
Plenum supports
(By others)
Timber Batten
(by others)
AHP / WAPP / ADMP ('H' - 4 / 'L' - 4)
ALSP ('A' + 18 / 'L' + 38)
MIN Plasterboard Opening
Plasterboard
(by others)
MIN Depth 40mm
MAX Depth 60mm
8
Plenum neck flush with
plasterboard face
(pre-plaster skim)
Installation Instructions
Installing the blanking plate
Where optional blanking plates have been supplied, these must be fitted to the rear of the
grille before the grille is installed into the builders work opening as it is not possible to install
these once the grille is in situ.
To determine the location for the blanking plates, offer up the grille to the builders work
opening and mark on the plaster flange using removable tape, the area where supply or
return plenums are not installed and where return air through the grille is not required.
IMPORTANT; Ensure that the blanking plate installation does not cover any active
area of the grille as this will restrict the flow of air through the grille.
Remove the grille from the opening and place face down on a suitable protected work
surface, ensuring the area is free from debris to avoid damaging the painted surface.
Blanking plates and foam insulation are supplied loose, in lengths for site cutting and
installation to the rear of the grille neck.
Cut the blanking plate and foam insulation to the required length(s) to cover the areas marked
as non-active, ensuring edges are clean and burr free.
To install the blanking plate/tray to the grille neck;
AHP / ADMP: Lay the foam insulation into the grille neck with backing facing away from the
grille face. Insert the straight edge of the blanking plate into the channel on the rear of the
grille neck and gently lever the tabs into the channel on the opposite side to engage the
blanking plate.
ALSP: With the foam insulation cut to the correct size to match the blanking tray, carefully
peal off the self-adhesive backing and stick the foam insulation to the inside of the blanking
tray.
Place the blanking tray over the neck of the diffuser and secure into position using No. 8 self
drilling screws (supplied by others) through the pre-formed Ø3.5 holes provided within the
blanking tray along both sides.
AHP, ADMP & ALSP: Once the blanking plate/tray is installed in the correct position, apply a
continuous bead of mastic to the joint between the blanking plate and the channel on both
sides to prevent vibration. Repeat these steps for each section of blanking plate until all nonactive sections of the grille are blanked.
9
Installation Instructions
Installing the grille (Finite)
The plaster in grille, complete with core, should be installed into the builders work opening,
retaining the plastic film on the front of the grille core to prevent marks during the installation.
IMPORTANT; The grille core can only be installed within the border in one
orientation. Ensure correct orientation of the air blades before final screw fixing
into plasterboard opening.
Ensure the grille border is flat and level before fixing it in place then secure using counter
sunk head 3.5 drywall screws every 300mm. Screw through the holes in the border, through
the plaster board and into the timber batten behind.
Ensure the screw heads are driven firmly into the border and sit below the top edge of the
grille border so they will not visible when the border is plastered. The border should be firm
with no movement. Jointing tape should be applied over the plaster frame to provide a good
adhesion surface for the plaster skim.
IMPORTANT; Care should be taken not to stretch the grille border apart during the
installation as this may affect core retainment.
With the grille secured in the plaster board panel, remove the grille core (refer to page 11 for
details on AHP & ADMP core removal) and store in a safe place, clearly marked with the
location reference to avoid accidental damage or disposal.
IMPORTANT; Mitred corners (if supplied), along with ALSP plaster in slot diffusers are fitted
with non-removable cores therefore suitable site masking of the grille core is required to
prevent damage.
The plaster can then be applied using the top edge of the grille border to level the plaster.
Excess plaster should be cleaned off the inside of the grille & border before it dries to avoid
staining or damage to the paint finish.
Installing the grille (Linear)
Linear grilles will be supplied with alignment pins and a blade alignment fixture (AHP &
ADMP). The alignment fixture is supplied flat and should be formed by hand before
installation.
Before installing the grille border into the builders work opening, arrange the grille sections
next to each other on a clean, level surface with the alignment pins and blade allignment
fixture to hand to ensure a good fit prior to installation.
Blade alignment fixture
Insert the alignment pins halfway into the alignment ports located in the border extrusion on
one grille section. Insert the formed blade allignment fixture into the extrusion channel at the
rear of grille border.
IMPORTANT; Install the allignment fixture with the grille installed within the border to ensure
correct orientation.
The grille border sections can then be offered up to the plaster board aperture and installed
in the same manner as the finite grilles detailed above, ensuring both allignment pins and
blade allignment fixture are correctly installed between each section.
Once the grille border has been secured in place, remove the core (refer to page 11 for
details on AHP & ADMP core removal) and centre the blade alignment fixture between the
two sections. Mastic should be applied to the top and bottom of the blade allignment fixture
where it meets the border extrusion to prevent movement or vibration.
Store the grille core sections in a safe place, clearly marked with the specific location
reference to avoid accidental damage or disposal and to ensure correct core is re-installed
within the relevant border section.
IMPORTANT; Each core section is specific to an individual border section.
10
Alignment pin
Installation Instructions
Removing the grille core (AHP)
Type AHP plaster in grille is supplied with a removable cores for access to supply or
return air plenums or volume control dampers (if specified). The AHP core is retained
within the border using friction bungs installed at the top and bottom of the grille core
support tubes.
To remove the grille core, use a suitable hook tool (supplied by others) to gently pull the
top blade away from the border at both ends of the grille.
IMPORTANT; Removal of the grille core from the border is a 2 person operation.
Do not attempt to remove the grille core as a single person operation as this can
cause damage to the grille or plasterwork finish.
Care should be taken when removing the grille core for the first time as the safety wire
restraints will not be fitted. When removing the grille core, excessive force can result in
damage to the plaster finish surrounding the grille border.
Installing the grille core (AHP)
Once the plaster/ paint finish is properly dry, unwrap the grille core and safety wires
ready for assembly. 2 No. safety wires are included in a bag supplied with each grille
core section.
Before installing the grille core, safety wires must be clipped to the pre-formed holes
provided at each end of each grille core. The holes are located on the top blade,
approximately 50mm in from each end blade support tube.
For grilles with 15° angle blades, holes are provided in top and bottom blades to allow
core roation and airflow direction control. Care should be taken when installing the
core to ensure correct blade orientation.
Disengage the clasp at the end of the safety wire, prise open the clasp and thread
through the pre-formed hole within the grille core. Ensure the clasp is correctly reengaged once installed (refer to photo). Repeat this process at each end of the grille
core. Open the clasp at the free end of each safety wire and prise open, ready for the
final assembly to the grille border.
Safety wires
IMPORTANT; Installation of the grille core into the border is a 2 person
operation. Do not attempt to fit the grille core as a single person operation as
this can cause damage to the grille or plasterwork finish.
IMPORTANT; The grille core must be supported with the blade containing the preformed hole at the top (refer to photo) and the finished grille face towards the operative
(pre-fored hole will be at the back of the blade).
With one operative supporting the grille core directly below the border, another
operative can carefully loop the safety wire around the corresponding mullion within the
border and thread the open clasp back through the pre-formed hole within the grille
border. Ensure the clasp is correctly re-engaged once through.
Once both wires are attached at both ends, the grille core can be offered in to the grille
border. The grille core should be lifted upwards until the core is level with the opening
before gently pushing the core into the border
Mullion
The grille core should be carefully pushed into the border ensuring even pressure along
the entire length of the grille.
Each grille section should be visually inspected once installed to ensure the grille core is
flush with the border profile. Any areas where the grille core does not sit flush should be
inspected.
11
Installation Instructions
Removing the grille core (ADMP)
Mullion
Type ADMP plaster in grille is supplied with removable cores for access to supply or return
air plenums or volume control dampers (if specified). The ADMP core is retained within the
border using spring clips, captured within support mullions spaced along the length of the
grille core.
Spring Clip
IMPORTANT; Removal of the grille core from the border is a 2 person operation.
Do not attempt to remove the grille core as a single person operation as this can
cause damage to the grille or plasterwork finish.
To remove the grille core, first locate the spring clips by looking into the grille through the air
discharge slots. Using a suitable non-abrasive pry tool (non-metallic), hook the grille
support tubes and gently pull the core away from the border, supporting the weight of the
core.
Care should be taken when removing the grille core for the first time as the safety wire
restraints will not be fitted. When removing the grille core, excessive force can result in
damage to the plaster finish surrounding the grille border.
Ensure support is provided along the entire length of the grille core to avoid
damage to the grille or plaster finish.
Installing the grille core (ADMP)
Once the plaster/ paint finish is properly dry, unwrap the grille core and safety wires ready
for assembly. 2 No. safety wires are included in a bag supplied with each grille core section.
Before installing the grille core, the safety wires must be attached to the pre-formed holes
provided at each end of the grille core. The holes are located on the bottom blade,
approximatley 50mm in from each end support tube.
Disengage the clasp at the end of the safety wire, prise open the clasp and thread through
the pre-formed hole within the grille core. Ensure the clasp is correctly re-engaged once
installed (refer to photo). Repeat this process at each end of the grille core. Open the clasp
at the free end of each safety wire and prise open, ready for the final assembly to the grille
border.
IMPORTANT; Installation of the grille core into the border is a 2 person operation.
Do not attempt to fit the grille core as a single person operation as this can cause
damage to the grille or plasterwork finish.
Mullion
IMPORTANT; The grille core must be supported with the blade containing the pre-formed
hole at the top and the finished grille face pointing away from the border opening.
IMPORTANT; The grille core can only be installed within the border in one orientation.
Ensure correct orientation of the air blades before final installation into the grille border.
With one operative supporting the grille core directly below the border, another operative
can carefully loop the safety wire around the corresponding mullion within the border and
thread the open clasp back through the pre-formed hole within the grille border. Ensure the
clasp is correctly re-engaged once through.
Once both wires are attached at both ends, the grille core can be offered in to the grille
border. The grille core should be rolled upwards into the opening ensuring the core is
correctly engaged within the mullion retaining lips.
Mullion Retaining Lip
Carefully push the core into the border ensuring that the grille tubes allign with the spring
clips fixed to border mullions.
IMPORTANT; Ensure grille is secured along the full length and that all spring clips are fully
engaged around the grille support tubes using a torch if necessary.
12
Spring
Clip
Order Details
Plaster In Liner Grilles (AHP, WAPP, ADMP)
F - AHP-15
/
Type
- Linear Construction
F Finite Construction
E End Section
M Middle Section
1500 x 150
/
P3
/
RAL 9010:20%
TE A1
EE
EE P0
EE
EE
EE
EE P2
EE
EE
EE
EZE P3
EE
EE
EE
EE P4
EE
EE
EE
EE P6
EE
EU
LxH
(see page 3 & 4)
Grille Type
AHP-0
AHP-15
WAPP-0
WAPP-15
ADMP-1
EXAMPLE
Make: TROX
Type: F-AHP-15 / 1500 x 150 / P3 / RAL9010:20%
Mill Finish Aluminium
Powder coated to RAL
9010:50% (white)
Powder coated to RAL
9006:25% (silver grey)
Standard Finish
Powder coated to RAL
9010:20% (white)
Powder coated to RAL
9005:20% (black)
Special Finish
State colour RAL..., BS...
Gloss level ...%
Blanking Plate
UKBP-AHP
Grille Type
AHP (covers WAPP)
ADMP
/
1000 x 150
/
D
LxH
(see page 3)
Foam Lining
- Not Lined
D 12mm Foam Lining
(supplied loose)
EXAMPLE
Make: TROX
Type: UKBP-AHP / 1000 x 150 / D / P4
/
P4
/
RAL9005:20%
TE
EE P0
EE
EE
EE
EE P2
EE
EE
EE P3
EE
EZE
EE
EE P4
EE
EE
EE
EE
EE P6
EE
EE
EU
Powder coated to RAL
9010:50% (white)
Powder coated to RAL
9006:25% (silver grey)
Powder coated to RAL
9010:20% (white)
Standard Finish
Powder coated to RAL
9005:20% (black)
Special Finish
State colour RAL..., BS...
Gloss level ...%
13
Order Details
AK-P Plenums (AHP, WAPP, ADMP)
AK-G-P - ZH - D - DG
Type
AK-G-P
Plenum Type
ZH
Horizontal spigot (supply)
AH
Horizontal spigot (extract)
ZV
Vertical spigot (supply)
AV
Vertical spigot (extract)
900 x 150 x 198 x 1
/
LxH
(see page 5)
Spigot Quantity
Spigot Diameter
Plenum Damper
0
No Damper.
Opposed blade damper fitted within plenum.
AG
Individually adjustable air pattern control blades fitted within plenum.
D
Opposed blade damper as ...-AG plus a set of individually adjustable
DG
air pattern control blades fitted within plenum.
Internal Lining
0
No lining.
12mm foam lining.
D
EXAMPLE
Make: TROX
Type: AK-G-P - ZH - D - DG / 900 x 150 x 198 x 1
Plaster In Slot Diffuser (ALSP)
F - ALS25P - T2 - 2
Type
- Linear Construction
F Finite Construction
E End Section
M Middle Section
Grille Type
ALS20P
ALS25P
Internal Style
S
Return (without blades)
NA
Non-active (without blades)
T2
2 blades with spreader plate
EXAMPLE
Make: TROX
Type: F-ALS25P - T2 - 2 / 1800 / P3
14
/
1800
/
P3
Diffuser Length (mm)
No. of Slots
ALS20P Slots 1 - 4
ALS25P Slots 1 - 4
/
RAL 9010:20%
TE A1
EE
EE P0
EE
EE
EE
EE P2
EE
EE
EE
P3
ZEE
EE
EE
EE
EE P4
EE
EE
EE
EE P6
EE
EU
Mill Finish Aluminium
Powder coated to RAL
9010:50% (white)
Powder coated to RAL
9006:25% (silver grey)
Standard Finish
Powder coated to RAL
9010:20% (white)
Powder coated to RAL
9005:20% (black)
Special Finish
State colour RAL..., BS...
Gloss level ...%
Order Details
ALSP Blanking Plate
UKBP-ALS25
Grille Type
ALS20
ALS25
/
2
/
1800
/
D
/ P4 / RAL9005:20%
No. of Slots
Foam Lining
- Not Lined
D 12mm Foam Lining
(supplied loose)
EXAMPLE
Make: TROX
Type: UKBP-ALS25 / 2 / 1800 / D
AK-ALSP Plenums
Type
AK-ALS20P
AK-ALS25P
No. of Slots
Plenum Type
ZH
Horizontal spigot (supply)
AH
Horizontal spigot (extract)
ZV
Vertical spigot (supply)
AV
Vertical spigot (extract)
Internal Lining
0
No lining.
12mm foam lining.
D
/
1200 x 198 x 2 x 320
Length (mm)
Overall Height including
diffuser plus any neck extension
1)
Spigot Diameter No. of Slots
Plenum Damper
0
No Damper.
M
Spigot Damper.
NOTE:
1) Overall height (including diffuser height)
= Spigot Dia. + 122 + Extension 'A'
EXAMPLE
Make: TROX
Type: AK-ALS25P - 2 - ZH - D - M / 1200 x 198 x 2 x 320
15
Subject to change · All rights reserved © TROX UK (08/2016)
AK-ALS25P - 2 - ZH - D - M