Cube interior door systems Technique reddot design award winner 2004 reddot design award winner 2009 reddot design award winner 2011 reddot design award winner 2014 content Technique CUBE door and frame systems 3 - 9 CUBE door and frame systems 10 - 11 CUBE entrance doorsets 12 - 13Sous en DRESS Skirting Boards 14 - 23 Table of dimensions 24 - 34 CUBE sliding doors [PRODUCT CODE GROUP D] Light [D-LIC125] Technique 262 238 1435 Glass door in accordance with DIN 18101 for general purposes in interior construction; Toughened safety glass (TSG) glass size 8mm in accordance with DIN 1249, ground edges The glass doors are blocked out for standard rebates in accordance with DIN with standard flap hinge The glass doors are supplied with an integrated 105mm wide lock device (Cube-Nux) on the lock side Integrated branded lock in accordance with DIN 18251, blocked out to take standard handle fittings, 18mm Niro strike plate, without key hole, key hole can be drilled subsequently The glass doors are equipped for KTM stainless steel 3D flap hinges, the flap hinges are supplied separately The glass doors are packed in cardboard boxes Flush rose cut-out not possible Vision panel 125 mm wide, central for door height, 8mm ES G glazing 1135 1045 1045 238 Glass [D-CG] 1435 Plain wooden door [D-CB] Models 1435 DOORLEAVES 1045 CUBE-DOORS RE-CUBE not possible 40 40 125 Flush doors in accordance with DIN 68706 for general purposes in interior construction, non-rebated, flush edge double doors in accordance with DIN 68706 Cube door leaves with integrated branded locks in accordance with DIN 18251, luxury lock with whisper latch, 24mm strike plate, optionally with magnetic lock 18mm strike plate, without key hole, key hole can be drilled subsequently The door leaves are supplied with 2 flap hinge cut-outs for concealed flap hinges, type Cubus DX61 3D The leaf frame comprises a four-sided double-layered composite cross-beam construction with an integrated full sheet of perforated chipboard The door leaf thickness is 39/40mm The adhesive bonding of the cover panels with the frame and the core conforms to DIN EN 204, stress group D3 Cube door leaves are packed in a cardboard box positive negative positive negative Partial matting Cut matting positive= streaks matted negative= streaks clear Lumexx / NoMEXX glazing [D-LMX] / [D-NMX] RE-CUBE-door leaves [D-CBR] Flush doors in accordance with DIN 68706 for general purposes in interior construction, with jamb rebate, flush edge double doors in accordance with DIN 68706 RE-CUBE door leaves with integrated branded locks in accordance with DIN 18251, magnetic locks with 18mm strike plate, without key hole, key hole can be drilled subsequently The door leaves are supplied with 2 flap hinge cut-outs for concealed flap hinges, type Cubus DX58D The leaf frame comprises a four-sided double-layered composite cross-beam construction with an integrated full sheet of perforated chipboard The door leaf thickness is 39/40mm The adhesive bonding of the cover panels with the frame and the core conforms to DIN EN 204, stress group D3 RE-CUBE door leaves are packed in a cardboard box 350 mm 410 610 410 Type LUMEXX 630 610 640 630 641 640 641 Glass (satinated) fitted flush with the door according to design and form Thickness glass according to design and form Typ NOMEXX: Clear glass positioned centrally in the doorleaf, standard or safety glass according design and form with glass beadings flush with the door“ Thickness glass according to design and form -4- -5- CUBE-DOORS DOORLEAVES Models [PRODUCT CODE GROUP D] Technique Handing hinged doors TRIOLA [D-LTR300] Vision panel with solid wood frame: finished in dark brown, light brown or black, textured paints, varnish, double glazing with white matt glass When door is pulled, the position of the hinges determines the handing Cut Cube [D-CB-GL] Left CUT 40 [GV40] CUT 50 [GV50] CUT 60 [GV60] Right Star CUT [GVstar] Cut-outs in the door leaf, including leaf edge with varnish or structured-lacquer surface Cut-outs in frame with varnish or structured-lacquer surface Gap Cube [D-CB-VI] 4 Inlays (5mm veneer inlays), in inlay surfaces in door leaf, including leaf edge and in the frame metal plaster strips (aluminium with stainless steel look) with veneered finish in the door leaf and frame but not on the edge of door leaf Handing sliding doors opening opening DIN Left -6- DIN Right -7- CUBE FRAME SYSTEMS [PRODUCT CODE GROUP F] CUBE FRAME [F-CB] CUBE SIDELIGHT frame type wind 2 [F-CB-w2] 1083 1435 241 CUBE FRAME SYSTEMS [PRODUCT CODE GROUP F] Cube wooden frames in accordance with DIN 18111 for all standard construction dimensions in accordance with DIN 18100 and standard door leaf dimensions in accordance with DIN 18101, double shell system for flush door leaves Only high-quality multi-layer MDF sheets are used for manufacturing Material thickness: 13mm, folded The facing width of the rebate frame is 52mm. The frame is mitred The facing width of the trim frame is 65mm. The frame is mitred The trim frames have been manufactured with fixed dimension and are narrowed to the relevant wall thickness on site The corner joints are fastened using excenters and screw plugs The absorption profiles have been fixed An adjustable stainless steel lock plate is built in Flap hinge carriers preassembled, Cubus flap hinges 3DX61 3D separate in package Door frame is packed in cardboard Technique Sidelight frame type wind 2 with two fixed side elements comprising two inner jambs and two bottom sills, with glazing beads Door leaf hinging on inner jamb Inner jambs and bottom sills are folded from MDF and adapted to the frame system Fixed side elements are designed for 8mm TSG glazing, thinner glazing requires a sealing tape to be used, for thicker glass, up to max. 23mm, the glazing beads can be post-cut The vertical and horizontal posts are packaged in a cardboard box, inner jambs and bottom sills are packaged separately Optional: suitable hidden sub-frames for fitting flush with the wall CUBE hidden sub-frames made from OSB sheets incl. aluminium angular lath 20x20mm, material thickness 45mm Precise indication of finished wall thickness required With respect to delivery of original Bod‘or KTM hidden sub-frames, the associated frames are reduced to the appropriate size at the factory No re-cutting on-site 65 65 13 45 2 13 17 15 17 CUBE FRAME for CUBE glass door leaf [F-CG] 13 15 13 2 45 CUBE SIDELIGHT frame type wind 1 [F-CB-w1] Sidelight frame type wind 1 with fixed side element comprising an inner jamb, bottom sill, with glazing beads Door leaf hinging on frame, optionally also on the inner jamb Inner jamb and bottom sill are folded from MDF and adapted to the frame system Fixed side element is designed for 8mm TSG glazing, thinner glazing requires a sealing tape to be used, for thicker glass, up to max. 23mm, the glazing beads can be post-cut The vertical and horizontal posts are packaged in a cardboard box, inner jamb and bottom sill are packaged separately -8- Cube wooden frames in accordance with DIN 18111 for all standard construction dimensions in accordance with DIN 18100 and standard door leaf dimensions in accordance with DIN 18101, double shell system with standard rebate for rebated door leaves Only high-quality multi-layer MDF sheets are used for manufacturing Material thickness: 13mm, folded The facing width of the rebate frame is 52mm. The frame is mitred The facing width of the trim frame is 65mm. The frame is mitred The trim frames have been manufactured with fixed dimension and are narrowed to the relevant wall thickness on site The corner joints are fastened using excenters and screw plugs The absorption profiles have been fixed An adjustable stainless steel lock plate is mounted Hinge assemblies ST85 / 7.5 pre-assembled, Bod‘or KTM glass door hinges 3D stainless steel delivered separately in the box Door frame is packed in cardboard -9- CUBE FRAME SYSTEMS [PRODUCT CODE GROUP F] RE-CUBE FRAME [F-CBR] CUBE SF frame [F-CBSF] Optional: suitable hidden sub-frames for fitting flush with the wall CUBE hidden sub-frames made from OSB sheets incl. aluminium angular lath 20x20mm, material thickness 28mm Precise indication of finished wall thickness required With respect to delivery of original Bod‘or KTM hidden sub-frames, the associated frames are reduced to the appropriate size at the factory No re-cutting on-site 1435 241 RE-Cube wooden frames in accordance with DIN 18111 for expanded construction dimensions in accordance with DIN 18100 Only high-quality multi-layer MDF sheets are used for manufacturing Material thickness: 13mm, folded The facing width of the rebate frame is 65mm. The frame is mitred The facing width of the trim frame is 52mm. The frame is mitred The trim frames are cut to the wall thickness The corner joints are fastened using excenters and screw plugs The absorption profiles have been fixed Lock plate installed for magnetic lock Flap hinge carriers preassembled, Cubus flap hinges 3D separate in package Door frame is packed in cardboard 1083 1083 1435 241 CUBE FRAME SYSTEMS [PRODUCT CODE GROUP F] Technique C UBE SF wooden frames in accordance with DIN 18111 for all standard wall opening dimensions in accordance with DIN 18100 and standard door leaf dimensions in accordance with DIN 18101, double shell system for flush door leaves O nly high-quality multi-layer MDF sheets are used for manufacturing A ccurately fitting door frames for assembly including blind frame Material thickness 13mm, folded T he facing width of the rebate frame is 33mm. The frame is mitred T he facing width of the trim frame is 46mm. The frame is mitred T he trim frames are cut to wall thickness (sub-structure is absolutely necessary) T he corner joints are fastened using excenters and screw plugs T he absorption profiles have been fixed A n adjustable stainless steel lock plate is mounted F lap hinge carriers preassembled, Cubus flap hinges 3DX61 3D separate in package D oor frame is packed in cardboard Includes: suitable hidden sub-frames for fitting flush with the wall CUBE-SF hidden sub-frames made from OSB sheets incl. aluminium angular lath 20x20mm, material size 20mm Precise indication of finished wall thickness required With respect to delivery of original Bod‘or KTM hidden sub-frames, the associated frames are reduced to the appropriate size at the factory No re-cutting on-site UC-DOOR FRAME SYSTEMS [PRODUCT CODE GROUP UC] UNDER-COVER DOOR FRAMES [UC-DRS] T he UNDER COVER frame is concealed in the wall and thus assembled invisibly T he frame consists of two vertical posts (flap hinge and lock plate part) and a horizontal post Ceiling-high model can also be supplied without horizontal post T he frame is made from a special ‚UNDER COVER Composite‘. It has the same elasticity coefficients as plasterboard and is designed to complement the relevant filler compound. This enables a perfectly seamless connection to the wall. This thus avoids the danger of cracks forming, even where there are large fluctuations in temperature. The frame material is suitable for further processing depending on the adjacent walls . Application of an adhesion primer is recommended prior to painting T wo concealed, three-dimensional adjustable metal hinges M agnetic lock plate Damping profile, delivered separately W all thickness from 100mm to max. 400mm wall end thickness. Wall end thickness is always the finished wall including 2x 12.5mm plaster or plasterboard D oor leaf dimensions Door leaf width: DIN – and special widths, double doors up to max. 1934mm door leaf heights: up to max. 2800mm F loor clearance The clearance from the top of the finished floor to the bottom of the door leaf is 5mm When installing in a construction shell, the floor recess must always be taken into consideration Door leaf thickness The frame is designed for flush door leaves sized between 39 and 40mm. Door jamb rebate without damping buffer is 45 x 15mm O ptional UC- doors are availabe in reverse opening version. - 10 - - 11 - CUBE-entrance doorsets 15 13 13 15 65 Patented connector system with corresponding inner and outer angles facilitates speedy, uncomplicated and wellfitting assembly of a sub-structure for a flush skirting board. 6 52 13 15 53/54 52 65 17 52 13 52 15 Note: Different covering outside dimensions. Special hidden sub-frame required Design Hygiene Flush skirting board means that the skirting is flush with the wall and does not protrude. In addition to these aesthetic and visual benefits, pieces of furniture can also be placed flush against the wall The flushness means the top of the skirting board does not need to be dusted off which also prevents wipe marks on the walls Assembly Impact sound insulation Door leaf [D-WE] Technique SOUS SUB-STRUCTURE FOR FLUSH SKIRTING BOARD SYSTEM [SB-SOU] 65 53/54 17 65 SKIRTING BOARDS [PRODUCT CODE GROUP SB] Technique Frame [F-WE] CUBE WE door leaves in accordance with DIN 68706/18101 Flush double doors with rebate 15 x 13mm, in accordance with DIN 68706 for special requirements with respect to sound insulation, burglary protection and climate protection CUBE WE wooden door frames in accordance with DIN 18111 Double shell designed as double rebate WE wooden embracing frames For flush double doors with single rebate in accordance with DIN 18111 Sound insulation in accordance with DIN 4109, Rw, P 42 dB Climate class in accordance with RAL RG 426, Climate Class III Burglary protection in accordance with DIN EN V 1627, Resistance class WK 2/RC 2 The door leaves are supplied up to a height of 2222mm with a tested PZ Schloss, 65mm mandrel size, 24mm stainless steel double strike plate in accordance with DIN18250 and concealed door flap hinge of type Cubus DX 101 S for resistance class RC2. From doorheight 2222 mm until 2471 mm a multilock system and 3rd hinge are included. From door height 2472mm, an automatic multipoint lock must be used. The frame consists of a four-sided double-layered composite crossbeam construction with stabilizers, as well as two 3.5mm thick composite board. A multi-layer special sandwich inlay is inserted The adhesive bonding of the cover panels with the frame and the core conforms to DIN EN 204, stress group D3 The door leaves are supplied with a built-in lowerable floor seal Cube door leaves are packed in a cardboard box Only high-quality multi-layer MDF sheets are used for manufacturing. Material thickness: 13mm, folded The facing width of the rebate frame is 52mm. The frame is mitred. The facing width of the trim frame is 65mm. The frame is mitred. The corner joints are fastened using excenters and screw plugs The trim frames have been manufactured with fixed dimension and are narrowed to the relevant wall thickness on site. Stainless steel safety lock plate with stainless steel plate built in Heavy flap hinge uptake fitted, 2x Cubus-101S flap hinges supplied separately in the package Door frame is packed in cardboard Since there is no direct contact between the floor, skirting board and the masonry, the flushness supports the desired impact sound insulation. Floor vibrations are not transferred. This has been confirmed by an external testing institution. 1 2 3 4 The patented connector system complete with corresponding inner and outer corners ensure assembly is simple and speedy. No need for timeconsuming mitring. Opportunities for improvement in both dry and solid construction. The skirting board is fitted to the masonry prior to plastering. The upper edge serves as the guide for the vertical and horizontal axes. The cleaning is considerably simplified, saving costly time. Aluminium rail 60mm, Dry wall construction Aluminium rail 60mm, Solid wall construction Dress flush skirting board for sub-structure SOUS [SB-DRE] Variety of design The choice of materials and colours of the skirting board to be adhered subsequently is unlimited. Various types of wood, laminate, natural and artificial stone or background-lit materials open up new design possibilities and/or functions such as e.g. signposts, coloured guiding systems or emergency lighting. Assembly The Dress skirting board is simply and easily adhered to the substructure. (Adhesive not included in delivery) - 12 - - 13 - CUBE TABLE OF DIMENSIONS DIN 1.1 CUBE TABLE OF DIMENSIONS DIN 1.1 Flush fitting door and frame, single leaf Flush fitting door and frame, double leaf Wall opening dimension Door leaf outside dimensions in accordance with DIN18101, for flush doors Frame rebate dimension Facing outside dimension Jamb outside dimension Clearance dimension Wall opening dimension Door leaf outside dimensions in accordance with DIN18101, for flush doors Technique Frame rebate dimension Facing outside dimension Jamb outside dimension Clearance dimension Height x width Height x widthHeight x width Height x width Height x width Height x width Height x width Height x widthHeight x width Height x width Height x width Height x width ------- x ------- x ------- x ------- x ------- x ------- x 635 ------- x 584 ------- x 591 695 ------- x 616 565 1500 ------- x 1434* ------- x 1441 1545 ------- x 1466 1415 ------- x 760 ------- x 709 ------- x 716 ------- x 820 ------- x 741 ------- x 690 ------- x 1750 ------- x 1684* ------- x 1691 ------- x 1795 ------- x 1716 ------- x 1665 ------- x 885 ------- x 834 ------- x 841 ------- x 945 ------- x 866 ------- x 815 ------- x 2000 ------- x 1934* ------- x 1941 ------- x 2045 ------- x 1966 ------- x 1915 ------- x 1010 ------- x 959 ------- x 966 ------- x 1070 ------- x 991 ------- x 940 2010x------- 1972x ------- 1980x ------- 2032x------- 1992x------- 1967x------- ------- x 1135 ------- x 1084 ------- x 1091 ------- x 1195 ------- x 1116 ------- x 1065 2135x------- 2097x ------- 2105x ------- 2157x------- 2117x------- 2092x------- ------- x 1260 ------- x 1209 ------- x 1216 ------- x 1320 ------- x 1241 ------- x 1190 2260x------- 2222x ------- 2230x ------- 2282x------- 2242x------- 2217x------- 2010x------- 1972x ------- 1980x ------- 2032x------- 1992x------- 1967x------- 2385x------- 2347x ------- 2355x ------- 2407x------- 2367x------- 2342x------- 2135x------- 2097x ------- 2105x ------- 2157x------- 2117x------- 2092x------- 2510x------- 2472x ------- 2480x ------- 2532x------- 2492x------- 2467x------- 2260x------- 2222x ------- 2230x ------- 2282x------- 2242x------- 2217x------- 2635x------- 2597x ------- 2605x ------- 2657x------- 2617x------- 2592x------- 2760x------- 2722x ------- 2730x ------- 2782x------- 2742x------- 2717x------- 2385x------- 2347x ------- 2355x ------- 2407x------- 2367x------- 2342x------- 2510x------- 2472x ------- 2480x ------- 2532x------- 2492x------- 2467x------- 2635x------- 2597x ------- 2605x ------- 2657x------- 2617x------- 2592x------- 2760x------- 2722x ------- 2730x ------- 2782x------- 2742x------- 2717x------- all constructions in accordance with basic dimension indicated so no W offer sufficient space for Cube flap hinge systems Reworking or construction with a 25mm wide door opening are required * Wooden doors 2 x 722 2 x 847 2 x 972 * Fully glazed 2 x 715 2 x 840 2 x 965 Finished wall thickness incl. plaster Finished wall thickness incl. plaster 65 3 52 17 13 Covering outside dimension Jamb outside dimension Wall opening inside dimension Door jamb rebate dimension Door jamb rebate dimension Jamb outside dimension Covering outside dimension Finished floor 5 5 Jamb outside dimension All dimensions in mm - 14 - Clearance dimension Leaf door dimension Door jamb rebate dimension 17 Finished wall thickness incl. plaster Door leaf outside dimension Covering outside dimension 65 7 13 Covering outside dimension Wall opening inside dimension Jamb outside dimension Door jamb rebate dimension Finished wall thickness incl. plaster Clearance dimension 17 65 13 7 13 Door leaf outside dimension Clearance dimension 65 Clearance dimension Wall opening inside dimension 3 52 13 13 15 Wall opening inside dimension Door leaf outside dimension 13 13 15 17 Finished floor All dimensions in mm - 15 - CUBE TABLE OF DIMENSIONS DIN 1.1 CUBE TABLE OF DIMENSIONS DIN 1.1 Flush fitting door, frame and wall, single leaf Flush fitting door, frame and wall, double leaf Wall opening inside dimension Subframe outside dimension Door leaf outside dimension in accordance with DIN18101, for flush doors Frame rebate dimension Facing outside dimension Jamb outside dimension Clearance dimension Wall opening inside dimension Subframe outside dimension Door leaf outside dimension in accordance with DIN18101, for flush doors Technique Frame rebate dimension Facing outside dimension Jamb outside dimension Clearance dimension Height x width Height x widthHeight x width Height x width Height x width Height x widthHeight x width Height x width Height x widthHeight x width Height x width Height x width Height x widthHeight x width ------- x ------- x 591 ------- x 616 ------- x 565 ------- x 1591 ------- x 1561 ------- x 1434* ------- x 1441 ------- x 1545 ------- x 1466 ------- x 1415 741 ------- x 711 ------- x 584 ------- x 695 ------- x 866 ------- x 836 ------- x 709 ------- x 716 ------- x 820 ------- x 741 ------- x 690 ------- x 1841 ------- x 1811 ------- x 1684* ------- x 1691 ------- x 1795 ------- x 1716 ------- x 1665 ------- x 991 ------- x 961 ------- x 834 ------- x 841 ------- x 945 ------- x 866 ------- x 815 ------- x 2091 ------- x 2061 ------- x 1934* ------- x 1941 ------- x 2045 ------- x 1966 ------- x 1915 ------- x 1116 ------- x 1086 ------- x 959 ------- x 966 ------- x 1070 ------- x 991 ------- x 940 2060 x ------- 2040 x ------- 1972 x ------- 1980 x ------- 2032 x ------- 1992 x ------- 1967 x ------- ------- x 1241 ------- x 1211 ------- x 1084 ------- x 1091 ------- x 1195 ------- x 1116 ------- x 1065 2185 x ------- 2165 x ------- 2097 x ------- 2105 x ------- 2157 x ------- 2117 x ------- 2092 x ------- ------- x 1366 ------- x 1336 ------- x 1209 ------- x 1216 ------- x 1320 ------- x 1241 ------- x 1190 2310 x ------- 2290 x ------- 2222 x ------- 2230 x ------- 2282 x ------- 2242 x ------- 2217 x ------- 2060 x ------- 2040 x ------- 1972 x ------- 1980 x ------- 2032 x ------- 1992 x ------- 1967 x ------- 2435 x ------- 2415 x ------- 2347 x ------- 2355 x ------- 2407 x ------- 2367 x ------- 2342 x ------- 2185 x ------- 2165 x ------- 2097 x ------- 2105 x ------- 2157 x ------- 2117 x ------- 2092 x ------- 2560 x ------- 2540 x ------- 2472 x ------- 2480 x ------- 2532 x ------- 2492 x ------- 2467 x ------- 2310 x ------- 2290 x ------- 2222 x ------- 2230 x ------- 2282 x ------- 2242 x ------- 2217 x ------- 2685 x ------- 2665 x ------- 2597 x ------- 2605 x ------- 2657 x ------- 2617 x ------- 2592 x ------- 2810 x ------- 2790 x ------- 2722 x ------- 2730 x ------- 2782 x ------- 2742 x ------- 2717 x ------- 2435 x ------- 2415 x ------- 2347 x ------- 2355 x ------- 2407 x ------- 2367 x ------- 2342 x ------- 2560 x ------- 2540 x ------- 2472 x ------- 2480 x ------- 2532 x ------- 2492 x ------- 2467 x ------- 2685 x ------- 2665 x ------- 2597 x ------- 2605 x ------- 2657 x ------- 2617 x ------- 2592 x ------- 2810 x ------- 2790 x ------- 2722 x ------- 2730 x ------- 2782 x ------- 2742 x ------- 2717 x ------- Minimum wall thickness 100mm * Wooden doors 2 x 722 2 x 847 2 x 972 * Fully glazed 2 x 715 2 x 840 2 x 965 Finished wall thickness incl. plaster Finished wall thickness incl. plaster 65 6 2 Wall opening inside dimension Wall opening inside dimension Subframe outside dimension Subframe outside dimension Clearance dimension 65 6 2 Covering outside dimension 5 Jamb outside dimension Covering outside dimension Finished floor All dimensions in mm Jamb outside dimension Clearance dimension Subframe outside dimension Door jamb rebate dimension Jamb outside dimension Wall opening inside dimension Door jamb rebate dimension Finished wall thickness incl. plaster Covering outside dimension Leaf door dimension Door jamb rebate dimension Door leaf outside dimension 5 45 15 15 Door leaf outside dimension 13 17 Wall opening inside dimension Subframe outside dimension Jamb outside dimension Covering outside dimension Clearance dimension Door jamb rebate dimension 17 Finished wall thickness incl. plaster Door leaf outside dimension Clearance dimension 65 6 2 13 2 45 15 13 - 16 - 65 6 2 17 3 52 6 2 45 2 0 3 52 6 2 45 20 17 Finished floor All dimensions in mm - 17 - RE-CUBE TABLE OF DIMENSIONS DIN 1.1 RE-CUBE TABLE OF DIMENSIONS DIN 1.1 Flush fitting door and frame, single leaf Flush fitting door and frame, double leaf Wall opening inside dimension Door leaf outside dimension in accordance with DIN 18101, for flush doors Door jamb rebate dimension Covering outside dimension Jamb outside dimension Clearance dimension Wall opening inside dimension Door leaf outside dimension in accordance with DIN 18101, for flush doors Door jamb rebate dimension Technique Covering outside dimension Jamb outside dimension Clearance dimension Height x width Height x widthHeight x width Height x width Height x width Height x width Height x width Height x widthHeight x width Height x width Height x width Height x width ------- x ------- x ------- x ------- x ------- x ------- x 660 ------- x 584 ------- x 591 695 ------- x 650 565 1510 ------- x 1434* ------- x 1441 1545 ------- x 1500 1415 ------- x 785 ------- x 709 ------- x 716 ------- x 820 ------- x 775 ------- x 690 ------- x 1760 ------- x 1684* ------- x 1691 ------- x 1795 ------- x 1750 ------- x 1665 ------- x 910 ------- x 834 ------- x 841 ------- x 945 ------- x 900 ------- x 815 ------- x 2010 ------- x 1934* ------- x 1941 ------- x 2045 ------- x 2000 ------- x 1915 ------- x 1035 ------- x 959 ------- x 966 ------- x 1070 ------- x 1025 ------- x 940 2015x------- 1972x ------- 1980x ------- 2032x------- 2006x------- 1967x------- ------- x 1160 ------- x 1084 ------- x 1091 ------- x 1195 ------- x 1150 ------- x 1065 2140x------- 2097x ------- 2105x ------- 2157x------- 2131x------- 2092x------- ------- x 1285 ------- x 1209 ------- x 1216 ------- x 1320 ------- x 1275 ------- x 1190 2265x------- 2222x ------- 2230x ------- 2282x------- 2256x------- 2217x------- 2015x------- 1972x ------- 1980x ------- 2032x------- 2006x------- 1967x------- 2390x------- 2347x ------- 2355x ------- 2407x------- 2381x------- 2342x------- 2140x------- 2097x ------- 2105x ------- 2157x------- 2131x------- 2092x------- 2515x------- 2472x ------- 2480x ------- 2532x------- 2506x------- 2467x------- 2265x------- 2222x ------- 2230x ------- 2282x------- 2256x------- 2217x------- 2640x------- 2597x ------- 2605x ------- 2657x------- 2631x------- 2592x------- 2765x------- 2722x ------- 2730x ------- 2782x------- 2756x------- 2717x------- 2390x------- 2347x ------- 2355x ------- 2407x------- 2381x------- 2342x------- 2515x------- 2472x ------- 2480x ------- 2532x------- 2506x------- 2467x------- 2640x------- 2597x ------- 2605x ------- 2657x------- 2631x------- 2592x------- 2765x------- 2722x ------- 2730x ------- 2782x------- 2756x------- 2717x------- For fitting frame on the wall, the wall opening should have at least these dimensions Re-Cube frames are produced according finish wall thickness and cannot be adjusted on site * Wooden doors 2 x 722 2 x 847 2 x 972 For fitting frame on the wall, the wall opening should have at least these dimensions Re-Cube frames are produced according finish wall thickness and cannot be adjusted on site Finished wall thickness Finished wall thickness Finished wall wall thickness thickness Clearance dimension Covering outside dimension Wall opening inside dimension Finished Jamb outside dimension 17 Door leaf outside dimension Clearance dimension Wall opening inside dimension Clearance dimension Jamb outside dimension Jamb outside dimension Covering outside dimension Covering outside dimension Finished floor All dimensions in mm - 18 - Door leaf outside dimension Covering outside dimension Wall opening inside dimension 17 Door leaf outside dimension Clearance dimension Wall opening inside dimension Jamb outside dimension 17 Door leaf outside dimension 17 Finished floor All dimensions in mm - 19 - RE-CUBE TABLE OF DIMENSIONS DIN 1.1 RE-CUBE TABLE OF DIMENSIONS DIN 1.1 Flush fitting door, frame and wall, single leaf Flush fitting door, frame and wall, double leaf Technique Frame dimension also apply to Frame dimension also apply to passing frames type 2.0 Glass swing doors passing frames type 2.0 Glass swing doors Wall opening inside dimension Subframe outside dimension Door leaf outside dimension in accordance with DIN18101, for flush doors Frame rebate dimension Facing outside dimension Jamb outside dimension Clearance dimension Wall opening inside dimension Subframe outside dimension Door leaf outside dimension in accordance with DIN18101, for flush doors Frame rebate dimension Facing outside dimension Jamb outside dimension Clearance dimension Height x width Height x widthHeight x width Height x width Height x width Height x widthHeight x width Height x width Height x widthHeight x width Height x width Height x width Height x widthHeight x width ------- x ------- x 591 ------- x 650 ------- x 565 ------- x 1591 ------- x 1561 ------- x 1434* ------- x 1441 ------- x 1545 ------- x 1500 ------- x 1415 741 ------- x 711 ------- x 584 ------- x 695 ------- x 866 ------- x 836 ------- x 709 ------- x 716 ------- x 820 ------- x 775 ------- x 690 ------- x 1841 ------- x 1811 ------- x 1684* ------- x 1691 ------- x 1795 ------- x 1750 ------- x 1665 ------- x 991 ------- x 961 ------- x 834 ------- x 841 ------- x 945 ------- x 900 ------- x 815 ------- x 2091 ------- x 2061 ------- x 1934* ------- x 1941 ------- x 2045 ------- x 2000 ------- x 1915 ------- x 1116 ------- x 1086 ------- x 959 ------- x 966 ------- x 1070 ------- x 1025 ------- x 940 2060 x ------- 2040 x ------- 1972 x ------- 1980 x ------- 2032 x ------- 2006 x ------- 1967 x ------- ------- x 1241 ------- x 1211 ------- x 1084 ------- x 1091 ------- x 1195 ------- x 1150 ------- x 1065 2185 x ------- 2165 x ------- 2097 x ------- 2105 x ------- 2157 x ------- 2131 x ------- 2092 x ------- ------- x 1366 ------- x 1336 ------- x 1209 ------- x 1216 ------- x 1320 ------- x 1275 ------- x 1190 2310 x ------- 2290 x ------- 2222 x ------- 2230 x ------- 2282 x ------- 2256 x ------- 2217 x ------- 2060 x ------- 2040 x ------- 1972 x ------- 1980 x ------- 2032 x ------- 2006 x ------- 1967 x ------- 2435 x ------- 2415 x ------- 2347 x ------- 2355 x ------- 2407 x ------- 2381 x ------- 2342 x ------- 2185 x ------- 2165 x ------- 2097 x ------- 2105 x ------- 2157 x ------- 2131 x ------- 2092 x ------- 2560 x ------- 2540 x ------- 2472 x ------- 2480 x ------- 2532 x ------- 2506 x ------- 2467 x ------- 2310 x ------- 2290 x ------- 2222 x ------- 2230 x ------- 2282 x ------- 2256 x ------- 2217 x ------- 2685 x ------- 2665 x ------- 2597 x ------- 2605 x ------- 2657 x ------- 2631 x ------- 2592 x ------- 2810 x ------- 2790 x ------- 2722 x ------- 2730 x ------- 2782 x ------- 2756 x ------- 2717 x ------- 2435 x ------- 2415 x ------- 2347 x ------- 2355 x ------- 2407 x ------- 2381 x ------- 2342 x ------- 2560 x ------- 2540 x ------- 2472 x ------- 2480 x ------- 2532 x ------- 2506 x ------- 2467 x ------- 2685 x ------- 2665 x ------- 2597 x ------- 2605 x ------- 2657 x ------- 2631 x ------- 2592 x ------- 2810 x ------- 2790 x ------- 2722 x ------- 2730 x ------- 2782 x ------- 2756 x ------- 2717 x ------- Minimum wall thickness 100 mm thickness Clearance dimension Clearance dimension Jamb outside dimension Jamb outside dimension Facing outside dimension Facing outside dimension Finished floor Finished floor All dimensions in mm - 20 - Blind frame outside dimension wall thickness Clearance dimension Finished Wall opening inside dimension Trim jamb inside dimension Door leaf outside dimension 17 Blind frame outside dimension Wall opening inside dimension wall Jamb outside dimension Finished Clearance dimension 17 Door leaf outside dimension Facing outside dimension Blind frame outside dimension Trim jamb inside dimension Wall opening inside dimension Blind frame outside dimension Jamb outside dimension Wall opening inside dimension Finished wall thickness Jamb outside dimension 17 Facing outside dimension Finished wall thickness Jamb outside dimension 17 Trim jamb inside dimension * Wooden doors 2 x 722 2 x 847 2 x 972 Trim jamb inside dimension When applying wall-embracing assembly without a hidden sub-frame, the inside wall opening dimension must be adapted to the jamb outside dimension. Height of jamb outside dimension + 5mm Width of jamb outside dimension + 10mm When applying wall-embracing assembly without a hidden sub-frame, the inside wall opening dimension must be adapted to the jamb outside dimension. Height of jamb outside dimension + 5mm Width of jamb outside dimension + 10mm All dimensions in mm - 21 - CUBE SF TABLE OF DIMENSIONS DIN 1.1 CUBE SF TABLE OF DIMENSIONS DIN 1.1 Flush fitting wall/frame single leaf Flush fitting surface wall/frame double leaf Wall opening inside dimension Subframe outside dimension Door leaf outside dimension in accordance with DIN18101, for flush doors Height x width Height x width Height x width Frame rebate dimension Facing outside dimension Jamb outside dimension Height x width Height x width Clearance dimension Height x width Height x width Wall opening inside dimension Subframe outside dimension Door leaf outside dimension in accordance with DIN18101, for flush doors Height x width Height x width Height x width Technique Frame rebate dimension Facing outside dimension Jamb outside dimension Height x width Height x width Clearance dimension Height x width Height x width ------- x 635 ------- x 625 ------- x 548 ------- x 555 ------- x 621 ------- x 580 ------- x 529 -------x1500 -------x 1491 -------x1412* -------x1419 -------x 1485 -------x1444 -------x 1393 ------- x 760 ------- x 750 ------- x 673 ------- x 680 ------- x 746 ------- x 705 ------- x 654 -------x1750 -------x 1741 -------x1662* -------x1669 -------x 1735 -------x1694 -------x 1643 ------- x 885 ------- x 875 ------- x 798 ------- x 805 ------- x 871 ------- x 830 ------- x 779 -------x2000 -------x 1991 -------x1912* -------x1919 -------x 1985 -------x1944 -------x 1893 ------- x 1010 ------- x 1000 ------- x 923 ------- x 930 ------- x 996 ------- x 955 ------- x 904 2010 x------- ------- x 1135 ------- x 1125 ------- x 1048 ------- x 1055 ------- x 1121 ------- x 1080 ------- x 1029 2135 x------- 2125x ------- 2082x------- 2090x------- 2123x ------- 2102x------- 2078x ------- ------- x 1260 ------- x 1250 ------- x 1173 ------- x 1180 ------- x 1246 ------- x 1205 ------- x 1154 2260 x------- 2250x ------- 2207x------- 2215x------- 2248x ------- 2227x------- 2203x ------- 2000x ------- 1957x------- 1965x------- 1998x ------- 1977x------- 1953x ------- 2010 x ------- 2000 x ------- 1957 x ------- 1965 x ------- 1998 x ------- 1977 x ------- 1953 x ------- 2385 x------- 2375x ------- 2332x------- 2340x------- 2373x ------- 2352x------- 2328x ------- 2135 x ------- 2125 x ------- 2082 x ------- 2090 x ------- 2123 x ------- 2102 x ------- 2078 x ------- 2510 x------- 2500x ------- 2457x------- 2465x------- 2498x ------- 2477x------- 2453x ------- 2260 x ------- 2250 x ------- 2207 x ------- 2215 x ------- 2248 x ------- 2227 x ------- 2203 x ------- 2635 x------- 2625x ------- 2582x------- 2590x------- 2623x ------- 2602x------- 2578x ------- 2385 x ------- 2375 x ------- 2332 x ------- 2340 x ------- 2373 x ------- 2352 x ------- 2328 x ------- 2760 x------- 2750x ------- 2707x------- 2715x------- 2748x ------- 2727x------- 2703x ------- 2510 x ------- 2500 x ------- 2457 x ------- 2465 x ------- 2498 x ------- 2477 x ------- 2453 x ------- 2635 x ------- 2625 x ------- 2582 x ------- 2590 x ------- 2623 x ------- 2602 x ------- 2578 x ------- 2760 x ------- 2750 x ------- 2707 x ------- 2715 x ------- 2748 x ------- 2727 x ------- 2703 x ------- Minimum wall thickness 100mm * Wooden doors 2 x 711 2 x 836 2 x 961 * Fully glazed 2 x 704 2 x 829 2 x 954 Finished wall thickness Finished wall thickness Wall opening inside dimension Blind frame outside dimension Clearance dimension Wall opening inside dimension Door leaf outside dimension Door jamb rebate dimension Jamb outside dimension Jamb outside dimension Covering outside dimension Blind frame outside dimension Jamb outside dimension Covering outside dimension Clearance dimension Door jamb rebate dimension Door leaf outside dimension Jamb outside dimension Covering outside dimension Door leaf outside dimension Door jamb rebate dimension Covering outside dimension Finished wall thickness Finished floor Finished floor All dimensions in mm - 22 - Clearance dimension Blind frame outside dimension thickness Clearance dimension wall Door jamb rebate dimension Finished Door leaf outside dimension Blind frame outside dimension All dimensions in mm - 23 - UC-DOORS Under-Cover TABLE OF DIMENSIONS DIN 1.1 UC-DOORS Under-Cover TABLE OF DIMENSIONS DIN 1.1 Wall covering frame, single leaf Wall covering frame, double leaf Construction shell opening dimension Door leaf outside dimension in accordance with DIN18101, for flush doors Frame rebate dimension Facing outside dimension Clearance dimension Construction shell opening dimension Door leaf outside dimension in accordance with DIN18101, for flush doors Frame rebate dimension Technique Facing outside dimension Clearance dimension Height x width Height x widthHeight x width Height x width Height x width Height x width Height x widthHeight x width Height x width Height x width ------- x 670 ------- x 584 ------- x 591 ------- x 761 ------- x 561 ------- x 1525 ------- x 1434* ------- x 1441 ------- x 1611 ------- x 1411 ------- x 795 ------- x 709 ------- x 716 ------- x 886 ------- x 686 ------- x 1175 ------- x 1684* ------- x 1691 ------- x 1861 ------- x 1661 ------- x 920 ------- x 834 ------- x 841 ------- x 1011 ------- x 811 ------- x 2025 ------- x 1934* ------- x 1941 ------- x 2111 ------- x 1911 ------- x 1045 ------- x 959 ------- x 966 ------- x 1136 ------- x 936 2030x------- 1972x------- 1980x------- 2065x------- 1965x------- 2030x------- 1972x ------- 1980 x ------- 2065 x ------- 1965x ------- 2155x------- 2097x------- 2105x------- 2190x------- 2090x------- 2155x------- 2097x ------- 2105 x ------- 2190 x ------- 2090x ------- 2280x------- 2222x------- 2230x------- 2315x------- 2215x------- 2280x------- 2222x ------- 2230 x ------- 2315 x ------- 2215x ------- 2405x------- 2347x------- 2355x------- 2440x------- 2340x------- 2405x------- 2347x ------- 2355 x ------- 2440 x ------- 2340x ------* Wooden doors 2 x 722 2 x 847 2 x 972 Construction shell opening dimension Construction shell opening dimension 12,5 Minimum 80 85 13 100 15 15 3 Net door leaf width (NDLW 1) Minimum 80 Door jamb rebate dimension Width (DJRMW)= NDLW 1 + NDLW 2 - 3mm Covering outside dimension Height (COMH) = DLOMH + DLFC + 88mm Non-active leaf 12,5 Active leaf Door leaf outside dimension Height (DLOMH) Net door leaf width (NDLW 2) 40 45 Wall thickness (WS) =X (0/-4mm) 100 Construction shell Height (CSH) = DLOMH + DLFC + 60mm (±5mm) Minimum 80 Construction shell dimension Width (CSW) = NDLW 1 + NDLW 2 + 80mm (±5mm) Door leaf floor clearance (DLFC) Door jamb rebate dimension Width (DJRMW) Covering outside dimension Width (COMW) = NDLW 1 + NDLW 2 + 167mm Door jamb rebate dimension Height (DJRMH) = DLOMH + DLOMH + 3mm Door leaf outside dimension Width (DLOMW) Covering outside dimension Height (COMH) = DLOMH + DLFC + 88mm 85 Construction shell Height (CSH) = DLOMH + DLFC + 60mm (±5mm) 40 15 12,5 Minimum 80 45 Jaw space (X) Wall thickness (WT) =X (0/-4mm) 100 Door leaf floor clearance (DLFC) Construction shell width (CSW) = DLOMW + 90mm (±5mm) Door leaf outside dimension Height (DLOMH) Covering outside dimension Width (COMW) = DLOMW + 177mm Door jamb rebate dimension Height (DJRMH) = DLOMH + DLOMH + 3mm 15 85 100 85 12,5 (with 13mm rebate/counter-rebate) 10-02-2012 All dimensions in mm - 24 - All dimensions in mm - 25 - RE-UC-DOORS (UNDER-COVER REVERSE) TABLE OF DIMENSIONS DIN 1.1 RE-UC-DOORS (UNDER-COVER REVERSE) TABLE OF DIMENSIONS DIN 1.1 Flush fitting door and frame, single leaf fitting door and frame, double leaf Construction shell opening dimension Door leaf outside dimension in accordance with DIN 18101, for flush doors Door jamb rebate dimension Covering outside dimension Clearance dimension Construction shell opening dimension Door leaf outside dimension in accordance with DIN 18101, for flush doors Door jamb rebate dimension Covering outside dimension Technique Clearance dimension Height x width Height x widthHeight x width Height x width Height x width Height x width Height x widthHeight x width Height x width Height x width ------- x 670 ------- x 584 ------- x 591 ------- x 761 ------- x 561 ------- x 1525 ------- x 1434* ------- x 1441 ------- x 1611 ------- x 1411 ------- x 795 ------- x 709 ------- x 716 ------- x 886 ------- x 686 ------- x 1175 ------- x 1684* ------- x 1691 ------- x 1861 ------- x 1661 ------- x 920 ------- x 834 ------- x 841 ------- x 1011 ------- x 811 ------- x 2025 ------- x 1934* ------- x 1941 ------- x 2111 ------- x 1911 ------- x 1045 ------- x 959 ------- x 966 ------- x 1136 ------- x 936 2030x------- 1972x------- 1980x------- 2065x------- 1965x------- 2030x------- 1972x ------- 1980 x ------- 2065 x ------- 1965x ------- 2155x------- 2097x------- 2105x------- 2190x------- 2090x------- 2155x------- 2097x ------- 2105 x ------- 2190 x ------- 2090x ------- 2280x------- 2222x------- 2230x------- 2315x------- 2215x------- 2280x------- 2222x ------- 2230 x ------- 2315 x ------- 2215x ------- 2405x------- 2347x------- 2355x------- 2440x------- 2340x------- 2405x------- 2347x ------- 2355 x ------- 2440 x ------- 2340x ------* Wooden doors 2 x 722 2 x 847 2 x 972 All dimensions in mm - 26 - All dimensions in mm - 27 - Technique CUBE SLIDING DOOR SYSTEMS - 28 - - 29 - CUBE SLIDING DOOR SYSTEMS MODELS [PRODUCT CODE GROUP UC] [PRODUCT CODE GROUP S] System NIXX / UC Sliding [UC-DRS-SLW] System TUBE Front [S-TFR] Freeliner wall-mounted system with guide rail embedded in the door leaf, incl. Soft-Close mechanism and wall-mounting board. Maximum door leaf weight 40kg. Freeliner wall-mounted system with round stainless steel guide rail, including two rollers on the door leaf, made from stainless steel with anti-lift-out protection, for wooden doors and glass doors. B D rechts öffnend 20 E 250 Leaf size calculation, double leaf DOOR LEAF MINIMUM HEIGHT Wall opening height + Guide rail space – Floor clearance = Door leaf minimum height D A 130 mm B 5 mm C D DOOR LEAF MINIMUM HEIGHT D Wall opening height A + Guide rail space 130 mm B – Floor clearance 5 mm C = Door leaf minimum height D DOOR LEAF MINIMUM WIDTH Wall opening width + Roller catch + Opening overlap = Door leaf minimum width H E 285mm F 30 mm G H DOOR LEAF MINIMUM WIDTH H 1/2 wall opening width E + Roller catch 285 mm F = Door leaf minimum width H A C 5 mm 30 G Leaf size calculation, single leaf 15 H NIXX Türblätter mit Soft-close-Funktion werden immer gegen die Öffnungsrichtung auf die Rollen geschoben. Bitte den notwendigen Platzbedarf prüfen. Ohne Soft-close-Funktion kann das Türblatt auch in Öffnungsrichtung aufgeschoben werden. Single leaf Double leaf Wall opening maximum 2300 x 900mm 2300 x 1840mm Door leaf surface weight 13.5kg/m2 (special central position) 13.5kg/m2 (special central position) Door leaf minimum height 125mm above wall opening size 125mm above wall opening size Door leaf minimum width see calculation above see calculation above Maximum door leaf height Dependent on height and width Dependent on height and width Maximum door leaf width 1215mm 1215mm Wall distance 16.1mm 16.1mm Opening options A A Cube sliding door leaves in accordance with DIN 68706 for general interior usage The sliding door leaves are flush on four sides with a rail slot and built-in stainless steel grabbers, 50mm diameter 4-sided solid wood frame construction The sliding door leaves come with a recessed guide rail inside the door leaf. Cube sliding doors are packaged in a cardboard box NIXX door leaves with soft-close function are always to be slid on the runners in the direction of the opening. Therefore, please check the space required. Please indicate the direction of opening when ordering Not available in conjunction with Bod‘or KTM High Gloss and Piano lacquer - 30 - Wood Glass Wall opening maximum Variable depending on structural circumstances Variable depending on structural circumstances Door leaf surface weight 21kg/m2 25kg/m2 Door leaf minimum height 20mm above wall opening size 20mm above wall opening size Door leaf minimum width Same covering outside dimensions or 100mm wider than wall opening Same covering outside dimensions or 100mm wider than wall opening Maximum door leaf height Variable depending on structural circumstances Variable depending on structural circumstances Maximum door leaf width Depending on surface up to 2000mm 1500mm Wall distance 5mm 5mm Opening options A, B A, B Passing frame Type passing frame 1.17B Type passing frame 1.25B OKFF F Türblattgewicht maximal 40 kg. Technique Only high-quality laminated MDF sheets are used in frame manufacture Material thickness: 13mm, folded The facing width of the frame is 52mm/65mm. The frame is mitred The corner joints are fastened using excenters and screw plugs The trim frames are cut to the fixed wall thickness, the brush seal is supplied separately Door frame is packed in cardboard Cube wooden sliding door leaves in accordance with DIN 68706 for general interior usage The sliding door leaves run floor to ceiling The sliding door leaves are flush with a rail slot and built-in stainless steel grabbers, 50mm diameter Full sheet of perforated chipboard and 4-sided double composite cross-beam construction The sliding door leaves come with drilled holes for an open guide rail system made from stainless steel with roller blocks on the wooden doors Cube wooden sliding doors leaves are packaged in a cardboard box Optional door leaf designs: CUT-CUBE, TRIOLA, LUMEXX, NOMEXX, CUBE-LICHT and GAP-CUBE Please indicate the direction of opening when ordering CUBE glass sliding doors (TSG) Glass size 10mm in accordance with DIN 1249 Designed for an open guide rail system made from stainless steel with roller block on the glass door leaf 50mm drill hole for grabbers, polished edges Please indicate the direction of opening when ordering - 31 - CUBE SLIDING DOOR SYSTEMS MODELS [PRODUCT CODE GROUP S] Technique System TUBE RAT [S-TOD] System TUBE TOP [S-TTB] Freeliner wall-mounted system with round stainless steel guide rail, including two rollers on the door leaf, made from stainless steel with anti-lift-out protection for wooden and glass doors. Freeliner wall-mounted system with round stainless steel guide rail, including two rollers on the door leaf, made from stainless steel with anti-lift-out protection for wooden doors Maximum door leaf weight 135kg. Wood Glass Wall opening maximum Variable depending on structural circumstances Variable depending on structural circumstances Wall opening maximum Variable depending on structural circumstances Door leaf surface weight 21kg/m2 25kg/m2 Door leaf surface weight 21 kg/m2 Door leaf minimum height 250mm above wall opening size 250mm above wall opening size Door leaf minimum height 20mm above wall opening size Door leaf minimum width Same covering outside dimensions or 100mm wider than wall opening Same covering outside dimensions or 100mm wider than wall opening Door leaf minimum width Same covering outside dimensions or 100mm wider than wall opening Maximum door leaf height Recommendation is max. 500mm above construction shell opening Recommendation is max. 500mm above construction shell opening Maximum door leaf height Variable depending on structural circumstances Maximum door leaf width Depending on surface up to 2000mm Maximum door leaf width Depending on surface up to 2000mm 1500mm Wall distance 15mm Wall distance 40mm 40mm Opening options A, B Opening options A, B A, B Passing frame Type passing frame 1.17B Passing frame Passing frame 1.33B Passing frame 1.33B Wood Only high-quality laminated MDF sheets are used in frame manufacture Material thickness: 13mm, folded The facing width of the frame is 52mm/65mm. The frame is mitred The corner joints are fastened using excenters and screw plugs The trim frames are cut to the fixed wall thickness, the brush seal is supplied separately Door frame is packed in cardboard Only high-quality laminated MDF sheets are used in frame manufacture Material thickness: 13mm, folded The facing width of the frame is 52mm/65mm. The frame is mitred The corner joints are fastened using excenters and screw plugs The trim frames are cut to the fixed wall thickness, the brush seal is supplied separately Door frame is packed in cardboard - 32 - Cube wooden sliding door leaves in accordance with DIN 68706 for general interior usage The sliding door leaves run from floor to ceiling The sliding door leaves are flush on four sides with a rail slot and built-in stainless steel grabbers, 50mm diameter Full sheet of perforated chipboard and 4-sided double composite cross-beam construction The sliding door leaves come with drilled holes for an open guide rail system made from stainless steel with roller blocks on the wooden doors Cube wooden sliding door leaves are packed in a cardboard box Optional door leaf designs: CUT-CUBE, TRIOLA, LUMEXX, NOMEXX, CUBE-LICHT and GAP-CUBE Please indicate the direction of opening when ordering Cube wooden sliding door leaves in accordance with DIN 68706 for general interior usage The sliding door leaves are flush on four sides with a rail slot and built-in stainless steel grabbers, 50mm diameter Full sheet of perforated chipboard and 4-sided double composite cross-beam construction The sliding door leaves come with cut-outs for an open guide rail system made from stainless steel with roller blocks above the wooden doors Cube wooden sliding door leaves are packed in a cardboard box Optional door leaf designs: CUT-CUBE, TRIOLA, LUMEXX, NOMEXX, CUBE-LICHT and GAP-CUBE Please indicate the direction of opening when ordering C UBE glass sliding doors (TSG) Glass size 10mm in accordance with DIN 1249 Designed for an open guide rail system made from stainless steel with roller block on the glass door leaf 50mm drill hole for grabbers, polished edges Optional door leaf designs: CUT-CUBE Please indicate the direction of opening when ordering - 33 - CUBE SLIDING DOOR SYSTEMS MODELS [PRODUCT CODE GROUP S] Technique System RAIL RÜT [S-RBW] System Rail Rit [S-RID] Freeliner wall-mounted system clad with real wood metal runners in natural ash, brown, black/brown or finished in a RAL colour, including 2 over-sized rollers made from brushed stainless steel with anti-lift-out protection. Freeliner wall-mounted system clad with real wood metal runners in natural ash, brown, black/brown or finished in a RAL colour, including 2 over-sized rollers made from brushed stainless steel with anti-lift-out protection. Optionally with Soft-Stop/Soft-Close design Wood Glass Wall opening maximum Variable depending on structural circumstances Variable depending on structural circumstances Wall opening maximum 1100mm Door leaf surface weight 21 kg/m2 25kg/m2 Door leaf surface weight 21kg/m2 Door leaf minimum height Same covering outside dimensions or 50mm higher than wall opening Same covering outside dimensions or 50mm higher than wall opening Door leaf minimum height Variable (depends on weight) Door leaf minimum width Same covering outside dimensions or 100mm wider than wall opening Door leaf minimum width Same covering outside dimensions or 100mm wider than wall opening Same covering outside dimensions or 100mm wider than wall opening Maximum door leaf height Variable depending on structural circumstances Maximum door leaf height Variable depending on structural circumstances Variable depending on structural circumstances Maximum door leaf width 1200mm Maximum door leaf width Depending on surface up to 2000mm 1500mm Wall distance 4mm Wall distance 4mm without frame/with flush frame 20mm with closed frame and/or skirting board 4mm without frame/with flush frame 20mm with closed frame and/or skirting board Opening options A, B Passing frame Passing frame 2.0 Opening options A, B A, B Passing frame Passing frame 2.0 Passing frame 2.0 Only high-quality laminated MDF sheets are used in frame manufacture Material thickness: 13mm, folded The facing width of the frame is 52mm/52mm. The frame is mitred The corner joints are fastened using excenters and screw plugs The trim frames are cut to the fixed wall thickness, the brush seal is supplied separately Door frame is packed in cardboard Cube wooden sliding door leaves in accordance with DIN 68706 for general interior usage The sliding door leaves are flush on four sides with a rail slot and built-in stainless steel grabbers, 50mm diameter Full sheet of perforated chipboard and 4-sided double composite cross-beam construction The sliding door leaves come with cut-outs for an open guide rail system with over-sized wheels made from stainless steel above the wooden door C UBE glass sliding doors (TSG) Glass size 10mm in accordance with DIN 1249 Designed for running wheels across the glass door leaf on open guide rails 5 0mm drill hole for grabbers, polished edges Optional door leaf designs: CUT-CUBE P lease indicate the direction of opening when ordering Wood Only high-quality laminated MDF sheets are used in frame manufacture Material thickness: 13mm, folded The facing width of the frame is 52mm/52mm. The frame is mitred The corner joints are fastened using excenters and screw plugs The trim frames are cut to the fixed wall thickness, the brush seal is supplied separately Door frame is packed in cardboard Cube wooden sliding door leaves in accordance with DIN 68706 for general interior usage The sliding door leaves are higher than the wall opening The sliding door leaves are flush on four sides with a rail slot and built-in stainless steel grabbers, 50mm in diameter Full sheet of perforated chipboard and 4-sided double composite cross-beam construction The sliding door leaves are supplied with a guide box incl. rollers on the inside of the door leaf Cube wooden sliding doors leaves are packaged in a cardboard box Optional door leaf designs: CUT-CUBE, TRIOLA and GAP-CUBE Please indicate the direction of opening when ordering leaf Cube wooden sliding doors leaves are packaged in a cardboard box Optional door leaf designs: CUT-CUBE, TRIOLA, CUBE-LICHT and GAP-CUBE Please indicate the direction of opening when - 34 - ordering - 35 - CUBE SLIDING DOOR SYSTEMS MODELS [PRODUCT CODE GROUP S] Technique System Floor [S-FW] System Ceiling [S-CEI] Freeliner ceiling-mounted system, with stainless steel lead profile, including two wheels in the door leaf , made from stainless steel with floor guide rail. Maximum door leaf weight 135kg. Aluminium ceiling-mounted guide rail system incl. mounting rail or suspension slots and 2-roller guiding mechanism for wooden and glass doors. Maximum door leaf weight 80kg. Wood Wood Glass Wall opening maximum Variable depending on structural circumstances Wall opening maximum Variable depending on structural circumstances Variable depending on structural circumstances Door leaf surface weight 21kg/m2 Door leaf surface weight 21kg/m2 25kg/m2 Door leaf minimum height Variable depending on structural circumstances Door leaf minimum height Variable depending on structural circumstances Variable depending on structural circumstances Door leaf minimum width 500mm Door leaf minimum width Variable depending on structural circumstances Variable depending on structural circumstances Maximum door leaf height Variable depending on structural circumstances Maximum door leaf height Dependent on height and width Dependent on height and width Maximum door leaf width Depending on surface up to 2000mm Maximum door leaf width Depending on surface up to 2000mm 1500mm Wall distance 11mm Wall distance Depending on where installed Depending on where installed Opening options A, B Opening options A, B A, B Passing frame Variable Passing frame Variable Variable Only high-quality laminated MDF sheets are used in frame manufacture Material thickness: 13mm, folded The facing width of the frame is 52mm/65mm. The frame is mitred The corner joints are fastened using excenters and screw plugs The trim frames are cut to the fixed wall thickness, the brush seal is supplied separately Door frame is packed in cardboard Cube wooden sliding door leaves in accordance with DIN 68706 for general interior usage The sliding door leaves are flush on four sides with a rail slot and built-in stainless steel grabbers, 50mm diameter Full sheet of perforated chipboard and 4-sided double composite cross-beam construction These sliding door leaves come with cut-outs to accommodate the wheels Cube wooden sliding doors leaves are packaged in a cardboard box Optional door leaf designs: CUT-CUBE, TRIOLA, LUMEXX, NOMEXX, CUBE-LICHT and GAP-CUBE Please indicate the direction of opening when ordering - 36 - Only high-quality laminated MDF sheets are used in frame manufacture Material thickness: 13mm, folded The facing width of the frame is 52mm/65mm. The frame is mitred The corner joints are fastened using excenters and screw plugs The trim frames are cut to the fixed wall thickness, the brush seal is supplied separately Door frame is packed in cardboard Cube wooden sliding door leaves in accordance with DIN 68706 for general interior usage The sliding door leaves run from floor to ceiling The sliding door leaves are flush on four sides with a rail slot and built-in stainless steel grabbers, 50mm diameter Full sheet of perforated chipboard and 4-sided double composite cross-beam construction These sliding door leaves come with cut-outs to accommodate the sliding mechanism Cube wooden sliding door leaves are packed in a cardboard box Optional door leaf designs: CUT-CUBE, TRIOLA, LUMEXX, NOMEXX, CUBE-LICHT and GAP-CUBE Please indicate the direction of opening when ordering CUBE glass sliding doors (TSG) Glass size 10mm in accordance with DIN 1249 50mm drill hole for grabbers, polished edges Optional door leaf designs: CUT-CUBE Please indicate the direction of opening when ordering - 37 - CUBE SLIDING DOOR SYSTEMS MODELS [PRODUCT CODE GROUP S] Technique Sliding doorset DOOR RUNNING IN THE WALL [S-IW] Wood Glass Wall opening maximum Variable depending on structural circumstances Variable depending on structural circumstances Door leaf surface weight 21 kg/m2 25kg/m2 Door leaf minimum height Variable depending on structural circumstances Variable depending on structural circumstances Door leaf minimum width Variable depending on structural circumstances Variable depending on structural circumstances Maximum door leaf height Variable depending on structural circumstances Variable depending on structural circumstances Maximum door leaf width Depending on surface up to 2000mm 1500mm Wall distance 4mm 4mm Passing frame Frame fitted on the wall / optionally flush with Frame fitted on the wall / optionally flush with the wall incl. subframe. Minimum wall thickness the wall incl. subframe. Minimum wall thickness 160 mm 160 mm Four shell closed frame with guide profile on one side/no guide profile in double door Design Only high-quality laminated MDF sheets are used in frame manufacture Material thickness: 13mm, folded The facing width is 65mm The corner joints are fastened using excenters and screw plugs The concealed guide rail system can be used for door leaves running right or left The brush seal is supplied separately Door frame is packed in cardboard Cube wooden sliding door leaves in accordance with DIN 68706 for general interior usage The sliding door leaves are flush on four sides with a rail slot and built-in stainless steel grabbers, 50mm diameter Full sheet of perforated chipboard and 4-sided double composite cross-beam construction The guide rail and the carriage incl. accessories are supplied separately Cube wooden sliding door leaves can be cut down above 40mm Cube wooden sliding door leaves are packed in a cardboard box - 38 - CUBE glass sliding doors (TSG) Glass size 10mm in accordance with DIN 1249 Designed for a guide rail system with clamping plate made from matt light metal alloy 50mm drill hole for grabbers, polished edges - 39 - Bod’or KTM GmbH 46395 Bocholt (Germany), Benzstraße 17 Telefon: +49 (0) 28 71 - 21 45 0 Fax: +49 (0) 28 71 - 18 44 00 www.bodor-ktm.com info@bodor-ktm.com