franklinfueling.com
VENT & FILL LINES
A COMPLETE DIESEL EXHAUST FLUID SYSTEM SOLUTION
A fully DEF/AdBlue® compatible system from a single manufacturer.
7
The included ½"
compression fitting
allows you to thread
the temperature
sensor into the
pipework system to
collect the temperature
of the DEF liquid.
6
1
3
4
AdBlue
SYSTEM
4
• All products are composed of DEF/AdBlue®
compatible materials including stainless
steel and various compatible elastomers.
• Diesel exhaust fluid will freeze at
approximately -11 °C (12 °F). To prevent
freezing of fluid in colder climate
installations, we suggest the recirculation
system detailed here. A TS-550 evo™ tank
gauge paired with temperature sensors
installed using the recirculation tee
assembly will ensure automated
recirculation and prevent freezing.
• X in part number = variable product length.
10
9
5
3
13
14
15
16 17
36 35 34
27
18
10
31
5
33
32
19
32 mm PRIMARY VENT LINE
110/90 mm FILL LINE
TANK PROBES, SENSORS & CONTROLS
41
TANK SUMP DISCHARGE LINE DETAIL
This line discharges the DEF liquid out to the dispenser sump.
2
SITE
STARTER
IMPORTANT NOTES
5
1
21
RETURN LINE
8
9
FEATURING THE DEF
RECIRCULATION SYSTEM
& UPP™ BRAND PIPE
Use this system setup diagram to help
you place your next order for a complete
diesel exhaust fluid compatible system.
11
This tee setup is
used inside the
dispenser sump to
connect the
discharge and return
lines. The setup also
facilitates adequate
exposure of the
temperature sensor
to the DEF liquid for
an accurate
temperature reading.
2
3
®
DISPENSER SUMP
RECIRCULATION
TEE ASSEMBLY
28 29 30
26
This line returns the DEF liquid back to the tanks.
TEMPERATURE
SENSOR DETAIL
SUBMERSIBLE
SYSTEMS
THE TOTAL
SYSTEMPUMPING
SOLUTION
TANK SUMP RETURN LINE DETAIL
11
10
9
5
3
20
12
22
23
10
24
11
Description
40
12
8
R
39
DISCHARGE LINE
10
37
11
38
1. 6" temperature sensor with ½" NPT
compression fitting
Model
FMP-TEM
2. 1" BSPT male x ½" NPT female bushing
408143001
3. 32 mm BSPT female termination fitting
82.032 SS BSPT
4. 32 mm electrofusion tee fitting
5. 32 mm electrofusion coupler
08-032-EIF
02-032-L
Description
19. 1½" NPT close nipple
20. 1" NPT x 2" NPT quick disconnect
coupler with ball valve
21. ½" NPT plug
22. ½" NPT female x 2" NPT male bushing
23. 2" NPT tee
6. 1 ½" BSPT male x 1" BSPT male bushing
408142001
24. 2" NPT close nipple
7. 1½" BSPT shear valve (1" outlet)
663100021*
25. Variable length, three phase, 50Hz
submersible turbine pump kit
8. 32 mm electrofusion 90° elbow coupler
9. 40/32 mm electrofusion reducer (test port)
10. 40 mm electrofusion entry seal
11. 40 mm electrofusion secondary coupler
407423002
LL2-XXX-I
41. 4" probe install kit
TSP-K4AS*
SSSHP-050
SST-200
407423001
46
45
25
104” - 168”
(2,640 mm - 4,265 mm)
43
47
403476901***
26. 40/32 mm electrofusion reducer
49-040-032
27. 32 mm primary pipe, 100 m coil
001-032-100-E
28. 32 mm stub
45
SSHB-200-050
48
44
05-032-L
29. 32 mm round flange
06.32
Model
Description
Model
30. 32 mm gasket for stub
07.32
42. ¾" automatic nozzle
DURADEF-LB
46. ¾" break away valve
BRK34SS-N
43. ¾" automatic nozzle
with miss-filling
prevention spout
DURADEF-MPD
47. ¾" BSPP x 1" BSPP
swivel break away
valve
OMNIDEF1X34P
DEF-MPD
48. ¾" NPT x 1" BSPP hose
FLDEF2XXXXX-2N-3P
12. 40/32 mm secondary contained pipe
001-040-032-XXX-E**
13. 1" NPT male x 1" BSPT transition nipple
408144001
31. 90 mm primary pipe, 6 m stick / 110
mm secondary sleeve, 6 m stick
001-090-006-E /
110-006-SC-E
100965A
32. 110/90 mm electrofusion entry seal
304-110-090-TP
14. 1" ball valve
TSP-SSP
40. Inventory probe
42
DEF10SSBVKIT
03-032-EIF
302-040
401220966
HANGING HARDWARE
Model
49-040-032-TP
02.40(SC)
38. Three-phase 380-415 Volt
control box, 220 Volt coil
*Includes TSP-UVPK probe head protective cover (shown).
12
Description
T550EDP/C
39. Stainless steel float
9
Model
37. TS-550 evo, conditions
15. 1" NPT EZ male x 1" NPT EZ female flex
DEF10XXXEFMXEZF
33. 90 mm electrofusion coupler
16. 1" NPT male x 1½" NPT reducing nipple
408141001
34. 90 mm stub
17. 1½" NPT check valve
403408931
35. 90 mm round flange
06.90
18. 1½" NPT 90° elbow
SSE90-150
36. 90 mm gasket for stub
07.90
*Requires mounting bracket (P/N 66320000) and stabilizer bar kit based on dispenser model.
**For XXX, use 050 for 50 m coil, or 100 for 100 m coil.
***Several other STP kits are available to meet the needs of specific markets and applications.
02.90
05-090-L
Description
44. Miss-filling
prevention device
45. ¾" NPT hose
FLDEF2XXXXX-2N-2N
FFS-0400 04-16
AdBlue® is a registered trademark of the German Association of the Automotive Industry (VDA).