ELECTRICAL INSTALLATION OF 63 KVA TRANSFORMER
AT RRTC RUBBER BOARD HAHARA ASSAM
SPECIFICATIONS AND SCHEDULE OF QUANTITIES
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- --------------------------Item.
Description
Qty Unit
Rate Amount
No.
Rs.
Rs.
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- -------------------------1
DRAWINGS
1.01
2.00
2.01
Preparation of drawings showing site plans, physical layouts
line diagram of the equipment, switch boards, sectional
details of switch gear, sub station, supplier structure,
consumer structure, earthing arrangement etc as required
by the Assam State Electricity Board/ Electrical Inspectorate
for the technical approval of the installaton, arranging inspection,
getting sanction for energisation, charging the transformer etc
complete.
NOTE:- Statutory fees remitted to Assam state Electricity Board/
Electrical Inspectorate will be reimbursed against production of
fee receipt.
REPAIRING OF THE EXISTING 11 KV STRUCTURE
Supply and fixing / replacing the damaged air break switch (gang
operated over head switch) full set including supply of all fixing
acessories for the 63 KVA transformer.
1 Set
1 set
2.02
Supply and fixing /replacing the damaged 11 KV lightning arrestors
1 set
2.03
Supply and fixing/ replacing damaged drop out fuses ( D.O fuses).
1 set
2.04
Supply and fixing/ replacing damaged 11 KV insulators
3 Nos
2.05
Supply and fixing/ replacing damaged LT insulators
3 Nos
2.06
Supply and fixing/ replacing the damaged & rusted miscelleneous
items like nuts, bolts,tie rod,interconnecting jumber and other
connecting materials etc of the above substation structure.
1 LS
2.07
Painting of the 8 meter steel pole structure including supply of
paint etc
2 Nos
2.08
Supply and fixing HT danger board
1 No
2.09
Supply and fixing LT danger board
1 No
3.00
Supply and providing electrical grade rubber mat of minimum
6 mm thickness
1 Sq m
4.00
Supply erection testing and commissioning of 63 KVA oil cooled
aluminium wound Distribution transformer of reputed make as per
relevant Indian standards with minimum 3 star rating including
transportation, loading/ unloading in the existing foundation
including supply of all acessories, transformer oil if required,
connections etc complete and charging of the transformer.
Note:- Specification of the transformer attached.
EARTHING
Design, fabrication, supply, and erection of earth pit,
earth electrode, copper flat, copper wire etc. according to
the standards of the Kerala Electrical Inspectrate and the
relevant Indian Standards.
Note:
The quantites shown are only approximate and work has to be
done as per actual site requirement and as per the electrical
electrical inspectorate standard
Providing Earth pit with 40 mm dia. GI pipe electrode 3.0 m
long including earth work excavation, filling with charcol and
salt, providing funnel, masonry chamber and plastering,
cover plate etc. complete incuding supply of all items.
1 set
5.02
-DO- Earth pit with G.I plate earth electrode 1200X 1200 X12 mm
size and total length not less than 3 meters including earth
work excavation, erection of plate electrode, filling the plate
sides with salt and charcol, providing funnel, GI pipe,
masonry chamber and plastering, cover plate etc. Complete as
per standard.
2 Set
6
Supply and laying/fixing of earthing conductor of copper flats/
wires of following sizes including necessary benches, copper
sockets, drilling holes, tinning, fixing , jointing etc. complete as
per approved scheme laid in trenches / walls with finishing
plastering whereever required as directed.
6.01
Supply and laying Copper flat of size 25 X 3 mm
1 M
6.02
Supply and laying Copper wire SWG 6
2 M
6.03
Supply and laying Copper wire SWG 8
1 M
6.04
Supply and laying Copper wire SWG 10
1 M
6.05
Supply and laying Copper wire SWG 12
1 M
7.01
6.02
Supply and laying G.I earthing flat of size 25 X 6 mm
Supply and laying G.I flat of size 25 X 3 mm
5
5.01
1 Set
80 M
10 M
7.03
7.04
7.05
7.08
7.09
Supply and laying
Supply and laying
Supply and laying
Supply and laying
Supply and laying
G.I Earth wire SWG 4
G.I Earth wire SWG 6
G.I Earthing conductor SWG 8
G.I Earth wire SWG 10
G.I Earth wire SWG 12
TOTAL
I/We hereby tender for the execution of works refered to above
in the aforesaid documents upon the terms and conditions contained or referred to therein and in accordance in all respects
with the specifications, designs, drawings and other relevant
details at the rates quoted by me/us.
Rate quoted is inclusive of all taxes and duties inlcluding
applicable service tax
Signature of the Tenderer
Date .........
Hahara transformer
30
30
1
1
1
M
M
M
M
M
See Factory Layout, Site Plan and Electrical Schematic
18.01 Supply and erection of GI Street light pole as per attached
drawing inluding earth work escavation, plastering etc complete
with the following acessories.
(a) 3 inch size class B , GI pipe 3 M long for street light pole.
(b) 40 mm size class B , GI pipe of approximate 1.3 M
long on each street light pole for cable connection from
bottom to PVC junction box.
(c) Suitable PVC junction box of approximate size
200 X 150 X 100 mm weather proof on the street light pole with
connector strip / terminals and 6 amp SP MCB of reputed make.
18.02
-DO- Supply and erection of GI Street light pole 3 M long
with all acessories of above item.
8 Nos
4000
32000
4 Nos
3500
14000
19
LIGHTING
19.01 Supply of 1x40 Watts ordinary fluorescent tube
light fittings.
40 Nos
350
14000
19.02
- DO - 1 x 40 W box type fiting PhilipsTMC 55/140 or uquavalent make
35 Nos
550
19250
19.03
- DO - 2 x 40 W box type fitting.
30 Nos
700
21000
19.04 Fixing of above 1x40 Watts/ 2x 40 Watts fluorescent tube
light fittings to walls or to underside of roof or to bottom members
of roof truss as directed including necessary down rods,ball
and socket, bracket and fixing accessories,3 core flexible
copper cable etc complete.
105 Nos
150
15750
19.05 Supply & fixing 60 Watts angle battern fittings complete with bulb.
8 Nos
100
800
19.06 Supply and fixing 60 Watts bulk head fittings complete with
bulbs etc. including all fixing accessories.
10 Nos
300
3000
19.07 Supply and fixing 150 W High bay metal halide fittings of reputed
make in the factory complete with lamp and all fixing acessories
and should be fixed at the required height as per the machine lay out/ factory floor requirement.
30 Nos
4500 135000
19.08 Supply of 2x11 Watts CFL Street light fitting BJSLF 211 Bajaj
with 2 Nos of 11 Watts CFL Lamp and anodised aluminium reflector
and glass acrylic cover of Bajaj make or equavalent reputed.
2 Nos
1000
2000
19.09 Supply of 2x40 Watts fluorescent street light fittings with tube
4 Nos
1500
6000
19.10 Supply of street light fitting 1X 40 Watts Crompton Greaves
or equavalent reputed with tube.
2 Nos
1500
3000
19.11 Supply of 70 W HPSV light fitting Cema make ASR 70
or equavalent reputed make including lamps.
1 Nos
2600
2600
19.12 Supply of CFL street light fitting of good finish with brass bulb
holder and 18 Watts CF Lamp of reputed make and anodised
aluminium reflector etc complete.
2 Nos
800
1600
19.13 Supply of 125 W HPMV lamp fittings type Crompton
MSP 121 H or equivalent Philips
4 Nos
4000
16000
17 Nos
600
10200
30 M
30 M
2 Nos
20
15
100
600
450
200
20
Fixing of above light fittings of item 19.08 to 19.13
including supply of all acessories and
suitable size G.I pipe for fixing the light fittings on street light
poles / building walls and interconnection from street light pole
junction box/ building ceiling rose using flexible copper cable.
21.01 Supply and laying 2 X 4 sq mm weather proof aluminium wire.
21.02 Supply and laying 2 X 2.5 sq mm weather proof aluminium wire.
22
Supply and fixing calling bell of reputed make
including all fixing accessories complete.
23.01 Supply and fixing ceiling fans, 1200 mm sweep, Make Crompton
Greaves/Rallis/Polar, including all fixing accessories,
regulator etc complete.
2 Nos
1200
2400
23.02
4 Nos
100
400
100
3000
7000
7000
Fixing of 1200 MM ceiling fan (fan will be supplied )
24
Supply and fixing 5A, 3pin receptacle plug socket with
piano type control switch, Make Anchor or equavalent on
lighting switch board.
25
Fabrication, Supply, Erection, Testing and Commissioning of
TPN Sub Fuse Board, 32A X 8 way in dust and vermin
proof sheet steel enclosure with 100 A SFU with 63 A HRC fuse
incommer and 32 A fuse bases and fuselinks of adequate
capacity complete with cable entry box, door interlock and
internnections complete.
30
Nos.
1 Set
26
SAFETY ITEMS
26.01 Supply and laying 6 mm thick electrical grade rubber mats
in front of switch boards.
18 M2
1000
18000
26.02 Supply and fixing LT metal danger boards.
1 Nos
100
100
26.03 Supply and fixing HT metal danger boards.
1 Nos.
100
100
26.04 Supply and fixing LT sticker danger boards.
20 Nos
50
1000
26.05 Supply and fixing LT fire extinguishers 5 Kg as per regulations.
(Dry chemical powder type).
6 Nos
3000
18000
26.06 Supply and fixing 2 Nos fire bucket with MS stand as per std
4 Sets
950
3800
26.07 Supply and fixing statutory display boards like artificial
respiration charts in photo framed display
1 No
400
400
26.08 Supply of 4.5 Kg Carbon dioxidefire extinguisher with ISI mark.
6 Nos
2500
15000
26.09 Supply of electrical grade rubber gloves.
26.3 Supply and fixing 9 litre capacity fire bucket with river sand.
2 Sets
6 Nos
600
750
1200
4500
27
Wiring of light points of factory building for group control
(4 to 6 points as directed) using PVC insulated copper cable
1.5 sq.mm. of Finolex make and 16 SWG copper earthing
conductor in ISI mark rigid PVC conduits complete with
piano type control switches in sheet steel enclourse from
Sub MCB Distribution Board upto and including ceiling rose.
Note:(4 to 6 Nos of light in single control considered as one group point)
35 points
650
22750
28
Wiring of light and fan points of factory building/ office
for independant control using PVC insulated copper cable of
1.0 sq.mm. of Finolex make and 16 SWG copper earthing
conductor in ISI Marked rigid PVC conduits with independent
switches in sheet steel enclosure from lighting Sub MCB DB
upto and including ceiling rose.
20 Nos
350
7000
1 Nos
500
500
60 Nos
900
54000
4 Nos
100
400
45
112500
29.01 Supply and fixing of remote Locable Stop push button station
in dust and vermin proof sheet steel enclosure,including all
fixing accessories complete.
29.02 Supply and fixing of a remote start & stop locable push
button station in dust and vermin proof sheet steel
enclosure including all fixing accessories complete.
29.03 Fixing of the dismantled push button stations.
30
Fabrication, supply and erection of steel supports made
2500 Kg
out of MS angles and flats as supports for starters,switches
push button stations, capacitors and cables as directed
including one coat of metal primer after fabrication and two
or more coats of smoke grey enamel paint after erection.
31
Supply and fixing 20 A 3 pin industrial power socket and
plug with 20 A MCB control in sheet steel enclosure with
accessories complete.
8 Sets
600
4800
32
Supply and fixing 15 A 3 pin power socket and plug with 15 A
piano type control switch (Anchor make or equivalent) on MS
boxes including all fixing accessories complete.
10 Nos
250
2500
33.01 Supply and laying PVC insulated single core 2.5 sq mm copper
cable make Finolex TWO runs with 14SWG copper earthing
conductor in ISI marked rigid PVC pipes of suitable size for
cicuit mains and for connecting 20 A / 15 A plug socket.
450
RM
90
40500
Note. For payment, one run will be measured.
33.02
- DO - THREE RUNS
1
RM
100
100
33.03
- DO - FOUR RUNS
150
RM
130
19500
33.04
- DO - FIVE RUNS
1
RM
140
140
33.05
- DO - SIX RUNS
60
RM
150
9000
33.06
- DO - EIGHT RUNS
60
RM
180
10800
60
RM
120
7200
34.01 Supply and laying PVC insulated single core 4.0 sq mm copper
cable make Finolex TWO runs with 14SWG copper earthing
conductor in ISI marked rigid PVC pipes of suitable size for
connecting 32 Amp D P switvh/ industrial plug socket.
Note. For payment, one run will be measured.
34.02
- DO - THREE RUNS
1
RM
135
135
34.03
- DO - FOUR RUNS
40
RM
140
5600
34.04
- DO - SIX RUNS
15
RM
160
2400
35.01 Earth work excavation for cable trenches in all classes of
soil including backfilling.
140 M3
200
28000
35.02 Laying bricks in cable trenches after laying of cables and
covering with 150 mm thick layer fine soil.
130 M2
220
28600
400
3200
300
9000
35.03 Supply outdoor LT cable markers and fixing them in concrete.
36.01 Supply and laying class B GI Pipe at road crossing, wall
8 Nos
30 M
crossing etc. as directed - size 63 mm dia.
36.02
- DO - 50 mm . dia
6 M
280
1680
36.03
- DO - 40 mm . dia
30 M
270
8100
36.04
- DO - 25 mm . dia
6 M
250
1500
37.01 Supply and fixing suitable terminal boxes in dust and vermin
proof sheet steel enclosure for motors from 1 HP upto and
including 5 HP.
4 No
200
800
37.02 Supply and fixing suitable terminal boxes in dust and vermin
proof sheet steel enclosure for motors from 7.5HP upto and
including 15 HP.
1 No
350
350
37.03 Supply and fixing suitable terminal boxes in dust and vermin
proof sheet steel enclosure for motors from 20 HP upto and
including 30 HP.
2 Nos.
500
1000
37.04 Supply and fixing suitable terminal boxes for motors from 40 hp
including 60 hp.
4 Nos.
900
3600
140
560
38
supply and fixing Electronic fan regulator 300/ 400 Watts for the 1200 mm
4
sweep ceiling fan.
39.01 Supply and fixing 63 A three phase ELCB of L&T
Hagger/MDS/Dattar/GEC or equavalent reputed make in the
MCB DB and interconnections inluding all fixing acessories.
1 Set
2500
2500
39.02
2 Sets
2000
4000
1600 M
50
80000
- DO - Supply and fixing 32 A three phase ELCB
40.01 Supply and laying of 32 mm PVC pipe(10 kg/cm2) at 60cm
below the factory floor for drawing under ground cable.
40.02
-DO- Supply and laying 50 mm PVC pipe(10 kg/cm2)
380 M
65
24700
40.03
-DO- Supply and laying 75 mm PVC pipe (6 Kg/cm2)
300 M
110
33000
40.04
40.05
-DO- Supply and laying 100 mm PVC pipe (4 kg/cm2)
-DO- Supply and laying 110 mm PVC pipe (4 kg/cm2)
500 M
60 M
150
170
75000
10200
41
CAPACITORS
1
1
1
1
9000
8000
4000
2000
9000
8000
4000
2000
Supply and fixing suitable capacitors for individual motors with all
fixing acessories and interconnections complete with motors/
motor starters.
41.01
41.02
41.03
41.04
25 KVAR
20KVAR
10 KVAR
5 KVAR
No
No
No
No
41.05 2 KVAR
41.06 1 KVAR
1 No
1 No
800
400
800
400
42
APFC CAPACITOR PANEL
42.01
Supply of 125 KVAR (125+25)centralized power factor
panel with L&T make MD-XL type low watt loss capacitors
in completely factory assembled condition with components of
L&T, Crompton Greaves or equavalent reputed make
incorporating the following acessories.
1. Incomer L&T make 250A MCCB
2. Current limiting contactor specially designed for capacitor
switching, GE or equavalent make.
3. HRC fuses for rack protection
4. Discharge resistors
5. Micro processor based APFC relay with programmable
switching programmes- 8 stage. ( Make- Belook or equavalent
reputed)
6. Provision for top and bottom cable entry.
7. Cooling fans.
8. Low loss MD-XL capacitors of L&T make in double
layer configuration in impregenated oil sealed container. This
shall be in 6 to 8 steps.
25-20–20 –20-15-10 -10--5 ratings.
9. Safety devices, controls etc pre wired and tested.
10. Powder coated cabinet using 14 swg sheet steel
11. Protection and cut off against leading PF
12. Provision for manual operation.
NOTE:At present 125 KVAR capacitor only to be provided for
automatic pf correction. But contactors , fuses, wiring etc to
be done for 150 KVAR now itself. 25 KVAR capacitor will
be provided by society in future if required.
1 Set
2E+05 160000
42.02
Supply and fixing additional 20 KVAR L&T make MD-XL
capacitor in the above APFC panel and directly connected for
the no load compensation of the 400 KVA transformer.
1 Set
16500
16500
42.03 Supply and fixing 63 Amp switch L&T make FN 63 with 50 A HRC fuses 1 No
in the above APFC panel for the 20 kvar capacitor for the
transformer no load compensation and connections etc complete.
1650
1650
42.04 Erection of the 125 KVAR APFC panel and inteconnections ,
minor civil works/ grouting etc complete.
2000
2000
1 Set
43.00 Supply and fixing MS box 6 X 4 inch size and providing connector
strip and covering with hylam sheet.
2 Nos
75
150
44.01 Supply and laying 1 inch size PVC pipe.
44.02 Chipping of floor/ wall for laying 1 inch size PVC pipe and
replastering.
6 M
6 M
15
30
90
180
45
3 Sets
200
600
10 M2
2000
20000
10 M2
500
5000
Supply and fixing 5A, 3pin receptacle plug socket 3 Nos with
3 Nos piano type control switch, Make Anchor or equavalent on
MS box.
46.01 Supply of 6 mm thick chequared plate with 2 coats of primer and
one coat of grey paint.
46.02 Laying of 6 mm thick chequared plate over the masonary duct
including cutting, grinding and providing flush type hooks to pull
out/ lift the plate easily.
(For angle iron supports rate will be given as per item No.30)
2.10
Supply and fixing voltmeter with selector switch.
2 Sets
1000
2000
2.11
Supply and fixing suitable FASD starter contactors, O/L relays,
push buttons etc of L&T make suitable for 50 Hp motor and
interconnections etc complete in the above 125 A feeder.
1 Sets
20000
20000
2.12
-DO- Supply and fixing suitable FASD starter contactors, etc
suitable for 40 Hp motor and interconnections etc complete
in the above 125/ 100 A feeder.
2 Sets
19000
38000
2.13
-DO- suitable for 30 HP in the 100A feeder.
2 Sets
18000
36000
2.14
-DO- suitable for 60 HP in the 125A feeder.
1 Sets
26350
26350
2.15
-DO- suitable for 25 HP in the 100A/ 63A feeder.
2 Sets
17000
34000
2.16
-DO- suitable for 20 HP in the 63A feeder.
2 Sets
14000
28000
2.17
-DO- suitable for 15 HP in the 63A feeder.
2 Sets
12000
24000
2.18
-DO- suitable for 10 HP in the 63A feeder.
1 Sets
10000
10000
2.19
-DO- suitable FASD starter for 7.5 HP in the 63A/ 32A feeder.
1 Sets
7000
7000
2.20
2.21
2.22
-DO- suitable D.O.L starter for 7.5 HP in the 63A/ 32A feeder.
-DO- suitable D.O.L starter for 5 HP in the 63A/ 32A feeder.
-DO- suitable D.O.L starter for 3/2/1 HP in the 32A feeder.
1 Sets
1 Sets
1 Sets
5000
3500
2500
5000
3500
2500
2.23
Supply & fixing variable speed D.O.L starters for 5/3/1.5 Hp motors
8 Sets
4000
32000
3.00
3.01
MCC -3
Fabricate, supply,erection testing and commissioning of MCC 3
cubicle type, floor mounting with 40X6 mm aluminium busbar for
phases and neutral with provision for fixing following acessories,
interconnections, earthing etc complete as per drawing.
Note:Panel MCC3 should be fabricated with space for
providing suitable FASD / D.O.Lstarter contactors, O/L relays,
push buttons etc in each feeder as per feeder ratings.
1 set
20000
20000
3.02
Supply & fixing 125 A TPN switch L&T make FN 125 incommer.
1 No
6700
6700
3.03
Supply and fixing 100 A HRC fuse for the above switch.
3 Nos
300
900
3.04
Supply and fixing 63 A TPN switch L&T make FN 63 with
50 /32A HRC fuse as outgoings.
2 Nos
3700
7400
3.05
Supply and fixing 100 A TPN switch L&T make FN 100 with
63A HRC fuse as outgoings.
1 Nos
4800
4800
3.05
Supply and fixing 32 A TPN switch L&T make FN 32 with
25 /20/16 A HRC fuse as outgoins.
10 Nos
3000
30000
3.06
Supply and fixing suitable FASD starter contactors, etc
suitable for 15 Hp motor and interconnections etc complete
in the above 63 A feeder.
1 Sets
12000
12000
3.07
-DO- suitable FASD starter for 7.5 HP in the 63A/ 32A feeder.
1 Sets
7000
7000
3.08
-DO- suitable D.O.L starter for 5 HP/ 3/ 2HP in the 32A feeder.
9 Sets
3500
31500
3.09
Supply and fixing RYB indications.
1 Set
700
700
3.10
Supply and fixing voltmeter with selector switch.
1 Set
1000
1000
4
4.01
MODIFICATION OF THE EXISTING MSB
Modification of the existing MSB by extending one side with
2X 50X10 mm aluminium busbar for phases and 1 X 50 X 10 mm
1 set
27000
27000
Al. busbar for neutral for fixing following additional switches/
acessories, interconnections, earthing etc complete.
(Existing MSB size:- Length- 3.85m, height-2.2m, width-0.50m )
4.02
Supply and fixing 250 A TPN switch L&T make FN 250 with
200/ 160 A HRC fuse as outgoings.
3 Sets
9700
29100
4.03
Supply and fixing 250 A four pole MCCB of L&T make.
1 Sets
9900
9900
4.04
Supply and fixing 250 A four pole MCCB of L&T make.
1 Sets
9900
9900
4.05
Erection of the above modified MSB and grouting etc complete.
(For angle iron supports /channels provided on the floor rate
will be given as per item No.30)
1 Sets
1000
1000
5
5.01
MODIFICATION OF THE EXISTING SUB SWITCH BOARDS
Modification of the existing SSB1 of 1.75m X 1.6m X 0.3m size by
extending the cable alley portion at both ends of the switch board
for fixing the seperately mounted FASD / D.O.L starter contactors,
O/L relays, push buttons to the respective feeders shown in the
drawing.
1 set
18000
18000
5.02
-DO- Modification of the existing SSB 2 of 1.6m X 1.6m X 0.3m
size with feeders shown in the drawing for fixing the starter
components.
-DO- Modification of the existing SSB 6 of 1.0m X 1.45m X 0.25m
size with feeders shown in the drawing for fixing the starter
components.
-DO- Modification of the existing SSB 7 of 1.5m X 1.5m X 0.3m
size with feeders shown in the drawing for fixing the starter
components.
1 set
16000
16000
1 set
12000
12000
1 set
14000
14000
5.05
Dismantling of existing FASD starter contactors, O/L relays of
40/ 30/25 HP motors from the existing starter panels and
fixing in the above modified switch boards and interconnections
etc complete with respective feeders.
8 Sets
1500
12000
5.06
-DO- Dismantling and fixing starter for 20/15/ 10/7.5 HP. motor
in the modified SSB's.
6 Sets
1000
6000
5.07
-DO- Dismantling and fixing D.O.L starter for 5/3/2/1 Hp motor
in the modified SSB's.
6 Sets
700
4200
6.00
Erection of the old / modified Sub Switch Boards of approximate
size 1.6 m X 1.5 m X 0.3 M in the new switch board room
and grouting etc complete.
Note:The switch boards, FASD/ D.O.L starters, DB's, cables etc are
dismantled and kept in the nearby genset room at a
distance of approximate 10 meters.
9 sets
450
4050
7.00
Erection of the old 8 way/ 6 way/ 4 way MCB DB Three phase/
3 sets
250
750
5.03
5.04
single phase wall mounting type.
8.00
Erection of the dismantled Fuse DB 8 way/ 6 way/ 4 way on the
wall/ floor of the new factory building and grouting etc complete.
3 sets
300
900
9.01
Fixing of the old FASD starter in ss enclosures of 7.5/ 15 HP
motors and connections.
(For steel supports if required separate rate will be given as per
item No. 30 )
-DO- Erection of the old FASD starter panels for 20/30 HP in
the new switch board room.
2 sets
125
250
2 sets
250
500
9.03
-DO- Erection of the old FASD starter panels for 40/50 HP .
2 sets
250
500
9.04
-DO- Erection of the old Auto transformer panels for 60 HP
motor the new switch board room.
1 sets
300
300
9.05
Fixing of the D.O.L starters for 5/3/2 HP motors and connections.
2 sets
50
100
9.02
10
MOTOR STARTERS
10.01 Supply & fixing of FASD starter in dust and vermin proof
1 SET
sheet steel enclosure make L&T with suitable over load relay,
isolator, single phasing preventor, cable entry boxes and interconnections
with isolator using copper cables etc for 60 HP motors - complete.
40000
40000
10.02 Supply & fixing of DOL starter in dust and vermin proof
sheet steel enclosure make L&T type MK1 with over load
relay, isolator,cable entry boxes and interconnections with isolator
using copper cables for 5 HP motor - complete.
1 Nos
3500
3500
10.03 Supply & fixing of DOL starter in dust and vermin proof
sheet steel enclosure make L&T type MK1 with over load
relay, isolator, cable entry boxes and interconnections with isolator
using copper cables for 3/2/1 HP motors - complete.
1 Nos
2500
2500
SWITCHES AND ISOLATORS
Supply and fixing switches/SFUs of the following rates.
11.01 63 A TPN fuse switch in S/S enclosure.
11.02 32 A TPN fuse switch in S/S enclosure.
11.03 32 A DP switch in M/S enclosure.
1 No
1 No
10 Nos
2000
1800
300
2000
1800
3000
11.04 Fixing of the old 63 /32A fuse switch in S/S enclosure.
1 No
2000
2000
12
3 sets
6000
18000
1 sets
6000
6000
11
Supply, Erection, Testing and Commissioning of
TPN MCB DB, 8 way for lighting ,of reputed mke in dust
and vermin proof sheet steel enclosure with 32 A 4 pole ELCB
cum MCB as incomer with 24 SP MCB outlet (6A/10A/16A)
with cable entry box,door interlock and interconnections
etc complete.
13.00 MCB DB POWER VERTICAL
13.01 Supply, Erection, Testing and Commissioning of vertical
TPN MCB DB, 12 way of reputed mke in dust and vermin
proof sheet steel enclosure with door interlock and following
acessories and interconnections etc complete.
13.02
13.03
13.04
13.05
13.06
13.07
Supply and fixing 4 pole 100 A MCCB set at 63A as incommer.
Supply and fixing 63 A ELCB Four pole..
Supply and fixing 32 A / 20/16A TP MCB outgoings.
Supply and fixing 32 A TP MCCB outgoings.
Supply and fixing 32 A / 25A DP MCB outgoings.
Supply and fixing 10/16/ 25A SP MCB outgoings.
14
LT POWER CABLES
1
1
2
1
2
24
Nos
Nos
Nos
Nos
Nos
Nos
4000
4000
900
2000
400
150
4000
4000
1800
2000
800
3600
1
60
1
62
RM
RM
RM
RM
1000
900
800
30
1000
54000
800
1860
Supply and laying 650/1100 V armoured PVC aluminium under
ground cables of (make.Universal/ Incab/Fort Gloster/ Torrent/
CCI/Tropodur/NICCO of the following sizes & laying
through PVC pipes provided 60 cm below the factory floor, in
built up trenches, steel members of roof, walls,floors,
including fixing identification tags, chipping of floors
or walls and all fixing accessories and materials etc.
as directed complete.
Note.
1. The quantity shown is only approximate and the successful
tenderer should measure the lengths at site for procurement.
2. Use solid core cables only upto 10 sq.mm.
14.01
14.02
14.03
14.04
3 1/2 X 400 Sq.mm Supply
3 1/2 x 300 Sq.mm Supply
3 1/2 x 240 Sq.mm Supply
3 1/2 x 400/ 300 / 240 Sq.mm Laying
14.05
14.06
3 1/2 x 185 Sq.mm Supply
3 1/2 x 185 Sq.mm Laying
400 RM
540 RM
650
25
260000
13500
14.07
14.08
14.09
3 1/2 x 150 Sq.mm supply
3 1/2 x 120 Sq.mm supply
3 1/2 x 120 Sq.mm Laying
1 RM
1 RM
2 RM
500
430
25
500
430
50
14.1
14.12
14.13
3 1/2 x 95 Sq.mm supply
3 x 95 Sq.mm supply
3 1/2 x 95 / 3 x 95 Sq.mm Laying
100 RM
100 RM
200 RM
300
270
20
30000
27000
4000
14.14
14.15
3 1/2 x 70 Sq.mm supply
3 1/2 x 70 Sq.mm Laying
120 RM
120 RM
250
20
30000
2400
14.16
14.17
3 x 70 Sq.mm supply
3 x 70 Sq.mm Laying
180 RM
180 RM
230
20
41400
3600
14.18
14.19
14.2
3 1/2 x 50 Sq.mm supply
3 x 50 Sq.mm supply
3 x 50 Sq.mm Laying
1 RM
60 RM
61 RM
200
190
20
200
11400
1220
14.21
14.22
3 1/2 x 35 Sq.mm supply
3 1/2 x 35 Sq.mm Laying
55 RM
55 RM
180
20
9900
1100
14.23
14.24
3 x 35 Sq.mm supply
3 x 35 Sq.mm Laying
200 RM
200 RM
175
20
35000
4000
14.25
14.26
3 1/2 x 25 Sq.mm Supply
3 1/2 x 25 Sq.mm Laying
200 RM
200 RM
170
20
34000
4000
14.27
14.28
3 x 25 Sq.mm Supply
3 x 25 Sq.mm Laying
700 RM
750 RM
165
20
115500
15000
14.29
14.3
4 x 16 Sq.mm
4 x 16 Sq.mm
- Supply
- Laying
20 RM
20 RM
150
20
3000
400
14.31
14.32
3 x 16 Sq.mm
3 x 16 Sq.mm
- Supply
- Laying
150 RM
180 RM
140
20
21000
3600
14.33
14.34
4 x 10 Sq.mm
4 x 10 Sq.mm
- Supply
- Laying
750 RM
790 RM
100
20
75000
15800
14.35
14.36
3 x 10 Sq.mm
3 x 10 Sq.mm
- Supply
- Laying
210 RM
210 RM
90
20
18900
4200
14.37
14.38
4 x 6 Sq.mm
4 x 6 Sq.mm
- Supply
- Laying
50 RM
50 RM
85
20
4250
1000
14.39
14.4
3 x 6 Sq.mm
3 x 6 Sq.mm
- Supply
- Laying
450 RM
484 RM
75
15
33750
7260
14.41
14.42
14.43
4 x 4 Sq.mm
3 x 4 Sq.mm
3 x 4 Sq.mm
- Supply
- Supply
- Laying
1 RM
1400 RM
1500 RM
70
65
15
70
91000
22500
15
Supply & laying 650/1100 V armoured PVC copper under ground
control cables of (make.Universal/CCI /Fort Gloster/ Torrent/
Incab/Tropodur/NICCO) of the following sizes and laying
through PVC pipes provided 60 cm below the factory floor, in
built up trenches, steel members of roof, walls,floors,
including fixing identification tags, chipping of floors
or walls and all fixing accessories and materials etc.
as directed - complete.
Note:
The quantity shown is only approximate and the successful
tenderer should measure the lengths at site for procurement.
15.01
15.02
15.03
12 X 1.5 Sq.mm - Supply
6 X 1.5 Sq.mm - Supply
12 X 1.5 / 6 X 1.5 Sq.mm - Laying
150 RM
1 RM
151 RM
200
150
15
30000
150
2265
15.04
15.05
4 X 1.5 Sq.mm - Supply
4 X 1.5 Sq.mm - Laying
1900 RM
1900 RM
100
15
190000
28500
15.06
15.07
3 X 1.5 Sq.mm - Supply
3 X 1.5 Sq.mm - Laying
1000 RM
1000 RM
80
15
80000
15000
15.08
15.09
15.10
2 X 2.5 Sq.mm - Supply
3 X 2.5 Sq.mm - Supply
3X 2.5/ 2 x 2.5 Sq.mm - Laying
300 RM
10 RM
310 RM
85
95
15
25500
950
4650
15.11
15.12
16
2 X 1.5 Sq.mm - Supply
2x 1.5 Sq.mm - Laying
2 RM
2 RM
70
15
140
30
CABLE GLANDING AND TERMINATION
Glanding and termination of the following sizes of power
and control cables including supply of glands, lugs, and all
materials tools and accessories with crimping etc.complete.
16.01
3 1/2 X 400 / 3 1/2 x 300 Sq.mm Aluminium
2 Nos
900
1800
16.02
3 1/2 X 240 Sq.mm Aluminium
1 Nos
800
800
16.03
3 1/2 X 185 Sq.mm Aluminium
22 Nos.
500
11000
16.04
3 X 150 / 120 Sq.mm Aluminium
1 Nos.
300
300
16.05
3 1/2 X 95 Sq.mm Aluminium
2 Nos.
150
300
16 Nos
140
2240
16.06
3X70 or 3 1/2 X 70 Sq.mm Aluminium
16.07
3x50 or 3 1/2 X 50 Sq.mm Aluminium
4 Nos
140
560
16.08
3x35 or 3 1/2 X 35 Sq.mm Aluminium
10 Nos
140
1400
16.09
3x25 or 3 1/2 X 25 Sq.mm Aluminium
44 Nos.
130
5720
16.1
4 X 16 or 3 X 16 Sq.mm Aluminium
12 Nos
120
1440
16.11
4 X 10 or 3 X 10 Sq.mm Aluminium
38 Nos.
110
4180
16.12
3x6 or 4 X 6 Sq.mm Aluminium
50 Nos
100
5000
16.13
3x4 or 4 X 4 Sq.mm Aluminium
80 Nos
60
4800
16.14
12 X 1.5 Sq.mm Copper
6 Nos
60
360
16.15
4 X 1.5 Sq.mm Copper
18 Nos.
60
1080
16.16
3 X 1.5 Sq.mm Copper
124 Nos.
60
7440
16.17
2 X 2.5 Sq.mm Copper
6 Nos.
60
360
2 Sets
7000
-DO- Earth pit with copper plate electrode 600 X 600 X 3 mm
size including supply of all items complete.
excavation, erection of plate electrode, filling the plate
sides with salt and charcol, providing funnel, GI pipe,
masonry chamber and plastering, CI cover plate etc.complete.
14000
-------------------Amount
-------------------
#REF!
#REF!
#REF!
#REF!
#REF!
#REF!
#REF!
#REF!
#REF!
#REF!
#REF!