Spectra i.Net®
Quick Wiring and Installation Manual
RJ45 Audio Out OP
Important Safety Instructions
WARNING – To reduce the risk of fire or electric shock, do not expose this equipment
to rain or moisture.
Equipment should not be exposed to dripping or splashing and no objects filled with
liquids should be placed on the equipment.
1. This manual is not a substitute for the complete Spectra i.Net® manual. Please read
the entire Spectra i.Net® installation manual. Always use common sense!
2. Read these instructions.
3. Keep these instructions.
4. Heed all warnings.
5. Follow all instructions.
6. Do not use this apparatus near water.
7. Clean only with dry cloth.
8. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
9. Do not install near any heat sources such as radiators, heat registers, stoves, or other
equipment (including amplifiers) that produce heat.
10. Only use attachments/accessories specified by the manufacturer.
11. Unplug this equipment during lightning storms or when unused for long periods of time.
12. Refer all servicing to qualified service personnel. Servicing is required when the
equipment has been damaged in any way, such as if the power-supply cord or plug is
damaged; liquid has been spilled or objects have fallen into the equipment; the
equipment has been exposed to rain or moisture; does not operate normally; or has
been dropped.
13. Follow COMPLETE instructions for wiring the sound masking system and ALL system
checks before powering the system on for the first time, to avoid irreversible damage
to the components. Ensure proper polarity for wiring with regard to power, data and
audio output.
14. Do NOT plug any Spectra i.Net® devices into a computer or network or like equipment
other than Spectra i.Net® devices unless specifically asked to do so in the installation
manual.
1
1.
2.
3.
4.
5.
6.
7.
8.
9.
Makesureyouhavethecorrectdrawings.
MakesureyouhavereceivedandreviewedtheSpectrai.Net®installationmanual.
Makesureyouhavereviewedallsafetyinstructions.
SecureOPs,i.LON®,Routers,Hubs,andMPIimmediatelyastheyareexpensiveitems.
ReadthroughtheSpectrai.Net®installationmanualcompletelyforallproperprocedures,
hookups,andinstallationinstructions.
Verifyallapplicablelocalandfederalcodes.
Forpower,use16gauge,2conductorwire.ObservepolarityoryouwillDAMAGEtheOP
equipmentirreversibly.
Reviewallaudioanddatawiringandconnectionsbeforebeginninginstallationof
equipment.
Usecommonsense.
RJ45
AudioOutOP
WiringReview
x USE568BWiringStandardsforDataWiring
x WIREMUSTBEPLENUMRATED
x FollowAllApplicableCodes
AUDIOWireConnection(RJ45)DATAWireConnection(RJ45)568B 8CONDUCTOR8CONDUCTOR
UseplenumratedCat5e,8conductorwith
RJ45connectors.
UseplenumratedCat5e,8conductorwith
RJ45connectors.
The information contained herein is proprietary to Lencore Acoustics Corp. and copyright protected. No part of this manual can be copied, used or distributed
without prior authorization from Lencore Acoustics Corp. © Copyright 2008-2011
Page 2
2
AudioCable(Straight)8Conductor
CableisrunfromOPtospeakersandfrom
speakertospeaker.
ThepinoutontheRJ45isstraight.Useonly8
conductor!
HelpfulHint:
UseadifferentcolorforyourCat5e/5Ecablesto
easilyidentifyaudiovs.datacableruns.
RJ45
AudioOutOP
AudioCable
NOTE:Lencorerecommends“longthroat”connectorsforintegrityandeasyuse.
DataCable(Straight)–8Conductor
CableisrunfromMPItothe1stOPorfromi.Lontothe
1stOP.CablesaretherunfromOPtoOP.
ThepinoutontheRJ45isstraight.
TIA/EIA–568Bwiringisstandard.
RJ45
Pin1andPin2arethenetworkwires(orange\whiteand
orangewires).
Pin3andPin6areforinitialization(green/whiteand
greenwires).
Pin4andPin5areforpaging(blueandblue/whitewires).
Pin 7 and Pin 8 are for music (brown/white and brown
wires).
NOTE:Lencorerecommends“longthroat”connectorsforintegrityandeasyuse.
To request a complete installation manual or for more information contact Lencore at
info@lencore.com Š www.lencore.com Š PH: 516.682.9292
3
Install OP’s sequentially. Follow drawing for
OP sequence and placement.
4
Schematic2
Spectrai.Net®SoundMasking
ConnectingSystemtoMPI
5
6
7
5
Spectra i.Net® Sound Masking
Additional Power Supplies with Common Ground Between Power Zones
Original Power Supply
Notice the common ground
between power zones.
8
Schematic 6
Spectra i.Net® Sound Masking
Continuity Testing Diagram
9
10
NOTES:
(Mark Any or All Changes on Drawings)
(NOTE Any Unexpected Field Conditions)
11
LENCORE ACOUSTICS CORP.
1 Crossways Park Drive West Woodbury, NY 11797
516-682-9292
info@lencore.com www.lencore.com
The information contained herein is proprietary to Lencore Acoustics Corp. and copyright protected.
No part of this manual can be copied, used or distributed without prior authorization from Lencore Acoustics
Corp. © Copyright 2015 REV 5001-15-05
12