GRAY MANUFACTURING
GRY/2431/2432
Heavy Duty Shop Equipment
HIGH-RISE AUTOMOTIVE TRANSMISSION JACK
•2 stage design: 1st stage 100% air operated for speed; 2nd stage hydraulic for precise control
•Swivel casters make for easy maneuverability •Nylon Speed-Strap™ quickly and conveniently
secures the load •Heavy duty ACME threaded screws provide greater bearing surface for easier tilt
adjustments •1,000 lbs. capacity.
ACCESSORIES
Part No. 41, All-purpose adapter kit - enables removal of transmission and transfer
case as one unit and allows for easy removal of front wheel drive transaxles.
Part No. 45, #45 Adapter - 4 ratcheting adapters stabilize irregular-shaped
transmission pans allowing one-person removal and installation.
Part No. 102, 2” Height adapter.
Part No. 120, #90 Adapter - designed for the vehicle where the exhaust passes next
to the transmission pan prohibiting easy transmission removal.
Part No. 121, 4T80E adapter.
Part No. 275-01027, Nipple pipe.
Part No. 310-31004, 4” gland nut.
Part No. 310-31010, 4” gland nut.
Part No. 312-01005, Air valve.
Part No. 353-43044, 2” gland nut.
Part No. 353-40121, Hydraulic/Power unit.
45
Part No. 848-04024, Spacer.
Part No. 8826-01013, Complete plunger kit.
Part No. 8848-01001, Complete seal kit.
Part No. 8848-01006, Caster without brake kit.
Part No. 8848-01007, Caster with brake Kit.
Part No. 8848-01009, Release knob and o-ring.
Part No. 8848-01011, Strap kit.
Min. Start Max. Lift
Height
Height
HTJ-1000 34-1/2”
72”
Part No.
120
Shop Tools & Equipment
HEAVY DUTY FORKLIFT JACKS
•Hold-to-Run™ Release Knob provides slower descent rate with precise operator control
•Two-Position Lift Pad adjusts to handle flat or edged surfaces •Low starting height
ght of 2-1/4”
2 1/4
Part No.
Capacity
FLJ-400C
FLJ-400A/H
FLJ-770B
FLJ-770A/H
8,000 lbs.
8,000 lbs.
15,442 lbs.
15,442 lbs.
Reach
Required Air
Max. Lift
Power
Pressure (Raised Position))
Height
16”
Hydraulic
N/A
7”
16”
Air/Hydraulic 155 psi
7”
16”
Hydraulic
N/A
7”
16”
Air/Hydraulic 155 psi
p
7”
ACCESSORIES
Part No. 480-01007, Wheel for FLJ-400C.
Part No. 8831-01002, Complete Seal Kit for FLJ-400C.
Part No. 8831-01003, Complete Plunger Kit for FLJ-400C.
Part No. 8890-01002, Complete Seal Kit for FLJ-770B.
HYDRAULIC WHEEL DOLLIES
•Offset column allows for open work space when removing wheel assemblies •3 swivel casters
provide great portability when moving wheel assemblies throughout the shop •Flexible design
both super single and dual wheel assemblies
works with bo
•Handles a variety
v
of tire and wheel assemblies including truck, aircraft,
airc
ground support, and farm equipment
applications •Internal bearings provide smooth rotation
of the arms for
fo aligning wheel assemblies to hubs
WD-150S, Floor Model.
Part No. WD
WDH-12, High Rise Model - Combines Fore/
Part No. WD
Aft with sideside-to-side tilting adjustments, air assisted
hydraulic power
pow system.
Overall
Length
WD-150S
39”
WDH-12 552-1/4”
Part No.
Max. Lift
Capacity
Height
8”
1,500 lbs.
51”
1,200 lbs.
ACCESSO
ACCESSORIES
Part No. 82, Adapter Arm, for small wheels.
PORTABLE AIR POWERED FLUID HANDLERS
•3 swivel casters to provide easy portability •Welded body construction •Air pressurized
system, no pump to wear out, uses shop air •12 psi factory set air regulator and 15 psi “popoff” valve •Low profile design of 9” •Manual valve creates an air tight seal to evacuate the fluid
•15 gallon capacity
Part No. AH-15, Anti-Freeze Handler.
Part No. OH-15, Oil Handler.
Part No. 16, High Rise Adapter.
HEAVY DUTY QUICPAC® SPIN-ON OIL FILTER CRUSHERS
•Accommodates up to 4 automotive spin-on oil filters •Interlocking feature prevents
door from opening until the ram is fully retracted •Removable catch basin allows
crusher to be cleaned periodically •100% air operated •Mounting stand included and
no complicated set-up or installation required •1/4 female NPT air inlet •3/4 female
NPT catch basin connection
Part No. QP-50, Automotive model, crushes filters up to 9” tall.
Part No. QP-160, Truck model, crushes filters up to 16” tall.
Specifications
QP-50
QP-160
Height ......................69-1/2” ....................85-1/2”
Width ..........................15” .......................20-1/2”
Depth .......................16-3/4” .........................
16-3/4” ..........................
Crushing Chamber
Height ..........................9” ........................16-1/4”
Width ...........................8” ...........................10”
Depth ...........................8” ............................8”
Air Pressure ....... 100 to 160 psi ........ 100 to 200 psi
ACCESSORIES
Part No. 232-20119, Vise Action T-Handle (2 small screws).
Part No. 232-20143, Vise Action T-Handle (large nut).
Part No. 312-01010, Exhaust Valve.
Part No. 859-01001, Air Valve.
QP-50
AH-15
OH-15
QP-160
E60
Extracts up to 95% of used oil from the filter
Gregg Distributors Ltd. - A Red, White & True Canadian Company!