FIRST ARTICLE INSPECTION REPORT
Form 1
Sheet 1 of 1
1. Part Number:
ZCC Partnumber
or own Partnumber
2. Part Name:
ZCC Partname
10. Supplier:
Company Name
11. Supplier Code
Supplier Code (if any)
12. MO/PO No.:
ZCC Purchase Order
Number
12a. Lot No.:
LOT/Batch Number
3. Serial No.:
XXXX or N/A
12b. Lot Size:
All parts per LOT
12c. Customer P/N:
Void or has to be filled in case of own
partnumber used in field 1.
ACC:
Accepted
parts per
LOT
13. Detail FAI:
(Single part drawing)
Assembly FAI:
(Assy drawing)
5a. Rev.:
DWG
Revision
4. FAIR Number:
Void or own Number
(must be unique for each
part)
19. Inspector
Stamp:
[STAMP]
20. Date
Date
REJ:
Rejected
parts per
LOT
14. Full FAI
(First FAI)
Delta FAI
(New revision)
14a. Reason for Delta FAI:
Fill in in case of Delta FAI. (e.g.: new drawing
release)
INDEX of Part Numbers or Sub-Assembly Numbers required to make the assembly noted above
15. Part Number
16. Part Name
18. FAI Report
Number
17. Part Serial
Number
18a. FAIR
Rev
N/A in case of part FAI
OR:
Part Number assy part 1
Part Name assy part 1
Part Number assy part 2
Part Name assy part 2
Part Number assy part 3
Part Name assy part 3
N/A or XXXX
N/A or XXXX
N/A or XXXX
Number - must be
unique for each
part
Number - must be
unique for each
part
Number - must be
unique for each
part
Rev. of
FAI
drawing
Rev. of
FAI
drawing
Rev. of
FAI
drawing
25. Disposition:
Any deviations from specifications/drawing to be listed here.
26. Reason For Discrepancy and Corrective Action Taken (Note Effective Date):
Reasons for discrepancy from specifications/drawing and corrective action documentation to be mentioned
here.
NOTE TO SUPPLIER:
THESE PARTS MUST BE RESUBMITTED AS A LOT WITH COPY OF THIS REPORT ACOMPANYING SHIPMENT
CAR REVIEWED BY:
27. Rework Order No.
21b. Engineering/Date
21d. QA/Date
Order No.
Sign/Date
Sign/Date (Mandatory)
28a Claim No.
No.
28b Order No.
No.
21a. Planning/Date
21c. Purchasing/Date
Sign/Date
Sign/Date
Form No. F-824-4 Revision B
23a.Govt. Insp
Sign/Date
24a. Date
23b. Customer
Sign/Date
24b. Date
2011-09-14
FIRST ARTICLE INSPECTION REPORT
1. Part Number:
ZCC Partnumber
Or own Partnumber
5. Material or Process
Name
2. Part Name:
ZCC Systems Partname
6. Specification Number
5a. Rev.:
DWG
Revision
8. Special
Process
Code
Form 2
Sheet 1 of 1
3. Serial No.:
XXXX or N/A
9.
Customer
Approval
Verification
4. FAIR Number:
Void or own
Number (must be
unique for each
part)
5b.
Acceptable
/ Deviation
10. Certification
Ref. Number
( ACC / D )
(YES / NO /
NA)
e.g. “passivating”
…
If any.
e.g. “screw”
e.g. M3x4 DIN 7985 ISO
7045
…
…
…
Yes /
No /
NA
ACC /
D
Number/Title of
cert attached.
Number/Title of
cert attached.
e.g. “washer”
Number/Title of
cert attached.
Standard parts,
materials or processes
to be filled in here.
11. Acceptance Test
Procedure Number
N/A or ATR/Test Report
Number
12.
Acceptance Report Results (Pass/No Pass), if applicable - Rejection Report No. (if any)
Results (PASS or FAIL) are to be filled in here or link to attached documentation.
13. Comments:
If any.
14.
Prepared By: Name, first Name
Form No. F-824-4 Revision B
15.
Date: XX.XX.XXXX
2011-09-14
FIRST ARTICLE INSPECTION REPORT
1. Part Number:
2. Part Name:
38200-143
Label Identification
Characteristic Accountability
5.
8. Drawing
6. B/Print
Char.
Requirement
Zone
No.
1
2
3
4
5
6
7
Square 9,5
76,2
19,0
12,0
Square 8,0
2,0
3x2,0
1.
2.
Drawing Format
3.
4.
5.
6.
7.
8.
9.
10.
11.
Letter to be News Gothic and Numbers
to be Arabic. Text height shall be 0.06
(1,5mm) minimum, Except note 6.
Dull black lettering, Borders & Lines.
Background to be dull Aluminum
MATL: Polyester overlaminate.
Dimensions of blank areas and line
thickness to be approximately as shown
Letters may be Arial Narrow and may be
smaller than 0.06 (1.5) as long as
remains legible
Serial Number, DMF and DWG REV
Information shall be filled accordingly.
Line thickness in areas indicated to be
0.010
Phantom Lines indicated are for
reference only and schall not be printed
Bar code shall be ECC 200. Bar code
shall contain following information: PNR,
SER, MFR, DMF.
Dimensions are in Millimeters,
Tolerances in accordance with DIN ISO
2768 v
12. Prepared By: Last Name, Name
Form No. F-824-4 Revision B
See Stamp
See Stamp
See Stamp
See Stamp
See Stamp
See Stamp
See Stamp
Form 3
Sheet 1 of 1
5a. Rev.:
3. Serial No:
B
N/A
Inspection/Test Results
9. Actual(s)
10. Designed Tooling
(when required)
4. FAIR Number:
141
Product Acceptance
11. Acceptance/deviation
Square 9,5
76,25
19,3
12,0
Square 8,0
-
Accepted
Accepted
Accepted
Accepted
Accepted
Accepted
Accepted
Design Requirement
Design Requirement
Accepted
Design Requirement
Accepted
Design Requirement
Design Requirement
Accepted
Accepted
Design Requirement
Accepted
Design Requirement
Accepted
Design Requirement
Accepted
Design Requirement
Accepted
Design Requirement
Accepted
Design Requirement
13. Date XX.XX.XXXX
2011-09-14