Product Description Sheet
Zeta® 7760 UV Wand System
1001 Trout Brook Crossing
Rocky Hill, CT 06067-3910
Telephone: (860) 571-5100
FAX: (860) 571-5465
Part # 98450
North American Engineering Center, July 2005
PRODUCT DESCRIPTION
The ZETA® 7760 UV Wand System is a high performance system designed for spot curing applications. The typical
cure area is 1/2" in diameter. The system utilizes an autoranging (90-265 VAC, 50-60 Hz) solid state power supply, a
200-watt high-pressure mercury arc lamp, a universal power supply, and a liquid light guide (sold separately) to deliver
16 – 20# W/cm2 of UV light at 250-410 nm. The extreme high-energy output results in extremely fast cure cycles,
particularly when tack-free surfaces are required.
The unit operates by engaging a foot switch that opens an internal shutter. The UV energy produced by the lamp is
immediately transmitted through a flexible light guide. The time required to complete the curing process depends
primarily on the distance from the end of the light guide to the surface of the adhesive and the type of adhesive used.
The exposure time can be controlled in either a manual or timed mode. Depressing the foot switch operates both
modes. In manual mode, the shutter will remain open as long as the foot switch is depressed. In timed mode, a
momentary actuation of the foot switch starts the exposure cycle. The duration of exposure will depend on the setting
of the new and improved timer that can range from 0-99.9 seconds. The Loctite® Zeta® 7760 can also be actuated by
external devices.
PRODUCT FEATURES
• 16 to 20# W/cm2 UV output with primary peak at 365 nm.
• UV spectral range of 250 – 410 nm.
• 200-Watt high-pressure mercury arc lamp.
• Hour meter for monitoring accumulated lamp life
• 1,000 hours of expected UV lamp life with proper handling
and maintenance.
• Manual or timed shutter light exposure, 0 to 99.9 seconds.
• Provides excellent depth-of-cure capabilities due to its
high UV output.
• Provides excellent tack free surface cure with optional enhanced
UVC light guides.
• Green “lamp on” indicator on front panel shows when lamp is on.
• Extremely cost effective when using multiple pole light guides.
(See next page).
o Provides for up to four (4) separate cure areas with a single UV source.
o No need to purchase additional UV sources and light guides.
• Provides 3-D curing capabilities.
Technical Data
• Dimensions: 11.0" wide x 12.5" deep x 7.6" high
• Weight: 19.5 lbs
• Power Supply: 90-265 V, 50/60 Hz input
Loctite® Zeta® 7760 System Includes:
• Operation Manual
• Ultraviolet Protection Glasses, P/N 97210
• AC Power Cord
• Foot Switch
Loctite® Brand Accessories (not included):
•
•
•
•
Dual Wand Adapter Kit, P/N 985045
UVC Enhanced Filter Kit, P/N 98598
Zeta® 7021 Spot Radiometer, P/N 98048
Light Guides (see below)
NOT FOR PRODUCT SPECIFICATIONS
Loctite is a TM of Henkel Corporation, U.S.A. © Copyright 2004. Henkel Corporation. All rights reserved
Product Description Sheet
Zeta® 7760 UV Wand System
1001 Trout Brook Crossing
Rocky Hill, CT 06067-3910
Telephone: (860) 571-5100
FAX: (860) 571-5465
Part # 98450
North American Engineering Center, July 2005
Loctite® Brand UV Light Guide Options:
Description
Standard
Enhanced
UVC output *
Dimensions
3 mm diameter x
1000 mm long
5 mm diameter x
1000 mm long
5 mm diameter x
1500 mm long
3 mm diameter x
1000 mm long
5 mm diameter x
1000 mm long
5 mm diameter x
1500 mm long
Single Pole
N/A
Item Numbers
2 Pole
3 Pole
983684 **
98596 **
4 Pole
98597 **
983677
N/A
N/A
N/A
983800
N/A
N/A
N/A
N/A
97328 **
98593 **
98594 **
97326
N/A
N/A
N/A
98543
N/A
N/A
N/A
* Enhanced UVC wands require optional UVC enhanced filter kit (P/N 98598) to optimize tack free surface.
** Requires the balancing adapter (P/N 985045) on initial set-up of light guides.
# - NOTE: Typical intensity as measured with a new lamp and new Loctite 5 mm x 1000 mm lightguide using a Loctite® Radiometer, item # 98048.
Recommendations
UV cure rate is dependent on lamp intensity, distance from the light source, depth of cure needed or bondline gap and
the light transmittance of the substrate through which the radiation must pass. Henkel Corporation recommends that
you test all adhesive applications under simulated or actual end use conditions to ensure the adhesive meets or
exceeds all required product specifications. Refer to the Loctite® Light Cure Product Selector Guide and product
Technical Data Sheets for curing specifications and performance.
NOT FOR PRODUCT SPECIFICATIONS
Loctite is a TM of Henkel Corporation, U.S.A. © Copyright 2004. Henkel Corporation. All rights reserved