®
Installation
Installat
Instal
allat
latiion Guide
Guid
de
for Self-Adhered Membranes
Hazleton, Pennsylvania 18202
Phone (570) 384-1230 - Fax (570) 384-3282
Toll Free (800) 894-4563
Winter Haven, Florida 33880
Phone (863) 297-5800 - Fax (863) 618-2193
Toll Free (866) 802-8017
4ADESO1 - 02/11 - 10,000- InnerWorkings
Manufacturing Facilities
Fernley, Nevada 89408
Phone (775) 575-6007 - Fax (775) 575-2314
Toll Free (800) 222-9782
ww w.polygla ss. co m
POLYGLASS® USA, Inc.
Corporate Office
1111 West Newport Center Drive
Deerfield Beach, Florida 33442
Phone (954) 233-1330 - Fax (954) 418-4453
Toll Free (888) 410-1375
e-mail: pgmarketing@polyglass.com
®
The new generation of ADESO self-adhered membranes is the
most innovative modified bitumen roofing product available in the
industry.
Index
ADESO self-adhered membranes are unique with years of
proven performance in the field as experienced by contractors,
buildings owners, architects and roofing professionals, placing
Polyglass ahead of the competition.
ADESO
ADESO self-adhered membranes comprise the latest in asphalt
adhesive technology as well as substantial, proven waterproofing
compounds available with different surfaces. Installed properly,
ADESO products will provide long lasting and durable roof coverings.
®
Technology
Features and Advantages
Special Features
FASTLap - SEALLap
®
®
Tools and Accessories
Applications
Do's and Don'ts
Details
General Recommendations
02
page 05
page 06
Acceptable Substrates
This revolutionary method of manufacturing ADESO
self-adhered membranes utilizing Polyglass’ patented dual
compound technology, makes Polyglass the industry leader in
self-adhered modified bitumen membranes for the residential and
commercial roofing markets.
page 04
page 07
page 07
page 08
page 09
page 14
page 15
page 31
03
®
Installation Guide
The new generation of ADESO self-adhered membranes is the
most innovative modified bitumen roofing product available in the
industry.
Index
ADESO self-adhered membranes are unique with years of
proven performance in the field as experienced by contractors,
buildings owners, architects and roofing professionals, placing
Polyglass ahead of the competition.
ADESO
ADESO self-adhered membranes comprise the latest in asphalt
adhesive technology as well as substantial, proven waterproofing
compounds available with different surfaces. Installed properly,
ADESO products will provide long lasting and durable roof coverings.
®
Technology
Features and Advantages
Special Features
FASTLap - SEALLap
®
®
Tools and Accessories
Applications
Do's and Don'ts
Details
General Recommendations
02
page 05
page 06
Acceptable Substrates
This revolutionary method of manufacturing ADESO
self-adhered membranes utilizing Polyglass’ patented dual
compound technology, makes Polyglass the industry leader in
self-adhered modified bitumen membranes for the residential and
commercial roofing markets.
page 04
page 07
page 07
page 08
page 09
page 14
page 15
page 31
03
®
As a manufacturer of ADESO self-adhered membrane. Polyglass
offers a wide range of ADESO self-adhered membranes which are
modified using true APP or SBS polymers on the top weathering
surface, built with a reinforced polyester and/or reinforced
fiberglass mat, and an aggressive self-adhesive formulation on
the bottom surface.
No Open Flames
ADVANTAGES
• Safe
• Easy to use
• Quick end lap application with patented FASTLap
• Quick & clean side lap with patented SEALLap
• Adhere to a variety of substrates
• Odorless
• Install with hand tools
• No open flames
Selvage Film “Factory-Applied Treatment”
Adhere to a variety of substrates
SPECIAL FEATURES
• Easy on your roofing projects, easy on you, Polyglass
EASYBOX®. Packaging is designed to open easily on the
roof.
FEATURES
• A true APP or SBS compound on the top
• Different finished surfaces (granules, reflective film or polyolefin film
with lay lines printed)
• High performance reinforced polyester or reinforced fiberglass mat
• Self-adhering compound on the bottom
• Split release film on the bottom surface
• Granule-free end lap with patented FASTLap
• Quick & clean side lap application with patented SEALLap technology
04
ADESO Technology | Features
Advantages | Special Features
05
®
Installation Guide
As a manufacturer of ADESO self-adhered membrane. Polyglass
offers a wide range of ADESO self-adhered membranes which are
modified using true APP or SBS polymers on the top weathering
surface, built with a reinforced polyester and/or reinforced
fiberglass mat, and an aggressive self-adhesive formulation on
the bottom surface.
No Open Flames
ADVANTAGES
• Safe
• Easy to use
• Quick end lap application with patented FASTLap
• Quick & clean side lap with patented SEALLap
• Adhere to a variety of substrates
• Odorless
• Install with hand tools
• No open flames
Selvage Film “Factory-Applied Treatment”
Adhere to a variety of substrates
SPECIAL FEATURES
• Easy on your roofing projects, easy on you, Polyglass
EASYBOX®. Packaging is designed to open easily on the
roof.
FEATURES
• A true APP or SBS compound on the top
• Different finished surfaces (granules, reflective film or polyolefin film
with lay lines printed)
• High performance reinforced polyester or reinforced fiberglass mat
• Self-adhering compound on the bottom
• Split release film on the bottom surface
• Granule-free end lap with patented FASTLap
• Quick & clean side lap application with patented SEALLap technology
04
ADESO Technology | Features
Advantages | Special Features
05
®
FASTLap means increased productivity
FASTLap provides a patented granule-free roll end feature.
The release film is clean and simple to remove. Minimizing the
effort and time required to achieve a perfect end seam.
2
1
• EASYBOX is precut on one side of the box.
• Easy removal of roll from side of the box – no more strain
from lifting the roll out of the box.
1. Selvage release film
2. Surfacing (granules/ sand)
3. Factory applied adhesive treatment
3
SEALLap quick waterproofing of side laps
• Easy folding process – the box is already flat – no more
work wasted breaking down boxes.
• Easy stacking of flat boxes creates simple disposal – an end
to scattered boxes littering your jobsite.
FASTLap Enhanced End Laps
The sealing of the end lap between two rolls of granular
modified bitumen membranes has long been an arduous and
troublesome operation. If granules are not heated and
embedded satisfactorily, a reliable and durable seam may
not be achieved. If the granular areas are overheated, the
reinforcement may warp, be damaged or loss of modified
adhesive may occur.
This is a unique patent-pending, factory-applied treatment on
the side lap of rolls to enhance sealability.
Advantages: Instant and Permanent bond between adjacent
membranes, even under low temperature conditions. Cost
Savings. No need for use of external caulk or mastics to ensure
lap bond. Labor Savings. Factory applied adhesive on the
selvage areas translates to less time to install roofing
membrane. Environmentally friendly. No need for external
mastics or heat, as required by competitors’ membranes.
ACCEPTABLE SUBSTRATES
Acceptable substrates for ADESO self-adhered applications:
- Polyisocyanurate
- GP Densdeck Prime (pre-primed board must still be primed)
DuraGuard® USG SecureRock®
- Asphalt impregnated, six-sided Woodfiber Board
- Primed Concrete
- New Plywood Decking or Primed Existing Plywood
- Joints must be taped (When in doubt, prime)
- Polyglass Elastobase® Poly/Sand – Base sheet, mechanically
attached, heat welded or set in hot asphalt
- Polyglass Elastoflex® SA V Base – Base sheet
Notes:
Polyglass recommends the use of Polyglass PG 500 mastic
and Polyglass PG 100 Asphalt Primer.
Contact Polyglass Technical Services for suitability of other
equal items at (866) 802-8017.
06
Special Features
FASTLap & SEALLap | Acceptable Substrates
07
®
Installation Guide
FASTLap means increased productivity
FASTLap provides a patented granule-free roll end feature.
The release film is clean and simple to remove. Minimizing the
effort and time required to achieve a perfect end seam.
2
1
• EASYBOX is precut on one side of the box.
• Easy removal of roll from side of the box – no more strain
from lifting the roll out of the box.
1. Selvage release film
2. Surfacing (granules/ sand)
3. Factory applied adhesive treatment
3
SEALLap quick waterproofing of side laps
• Easy folding process – the box is already flat – no more
work wasted breaking down boxes.
• Easy stacking of flat boxes creates simple disposal – an end
to scattered boxes littering your jobsite.
FASTLap Enhanced End Laps
The sealing of the end lap between two rolls of granular
modified bitumen membranes has long been an arduous and
troublesome operation. If granules are not heated and
embedded satisfactorily, a reliable and durable seam may
not be achieved. If the granular areas are overheated, the
reinforcement may warp, be damaged or loss of modified
adhesive may occur.
This is a unique patent-pending, factory-applied treatment on
the side lap of rolls to enhance sealability.
Advantages: Instant and Permanent bond between adjacent
membranes, even under low temperature conditions. Cost
Savings. No need for use of external caulk or mastics to ensure
lap bond. Labor Savings. Factory applied adhesive on the
selvage areas translates to less time to install roofing
membrane. Environmentally friendly. No need for external
mastics or heat, as required by competitors’ membranes.
ACCEPTABLE SUBSTRATES
Acceptable substrates for ADESO self-adhered applications:
- Polyisocyanurate
- GP Densdeck Prime (pre-primed board must still be primed)
DuraGuard® USG SecureRock®
- Asphalt impregnated, six-sided Woodfiber Board
- Primed Concrete
- New Plywood Decking or Primed Existing Plywood
- Joints must be taped (When in doubt, prime)
- Polyglass Elastobase® Poly/Sand – Base sheet, mechanically
attached, heat welded or set in hot asphalt
- Polyglass Elastoflex® SA V Base – Base sheet
Notes:
Polyglass recommends the use of Polyglass PG 500 mastic
and Polyglass PG 100 Asphalt Primer.
Contact Polyglass Technical Services for suitability of other
equal items at (866) 802-8017.
06
Special Features
FASTLap & SEALLap | Acceptable Substrates
07
®
APPLICATION INSTRUCTIONS
1. Application
A. Remove existing materials and obsolete penetrations
down to an acceptable substrate, repair any voids or
imperfections in the substrate.
B. For steep-slope underlayments, cut the 2-square rolls
into a minimum of 3 equal sections.
C. Unroll and allow membrane to relax in the sun for a recommended 15 minutes prior to installation in final location.
Tools
1. Trowel
2. Caulking Gun
3. Metal Head Hand Roller
4. Tape Measure
5. Utility Knives- Hook Blade, Straight Blade
1
6. Claw Hammer
7. Tin Snips
8. Hand Held Hot Air Welder
9. Silicone Hand Held Roller
2. Application
A. Measure leading edge for width of first sheet and snap straight
chalk line.
B. Lay the material flat in place, starting at the lowest point.
C. Align the membrane with chalk line at the lowest edge of
the roof.
D. Install in shingle fashion from lowest point to highest point on roof.
1
2
3
4
Accessories
1. Polyglass PG 500 TROWEL Grade Mod-Bit Adhesive –
10.3 oz cartridge
2. Polyglass PG 500 TROWEL Grade Mod-Bit Adhesive –
4.75 gal. Pail
3. Polyglass PG100 ASPHALT PRIMER – 14 oz spray Can
4. 80 lb (minimum) linoleum roller
2
08
Tools & Accessories
Applications
09
®
Installation Guide
APPLICATION INSTRUCTIONS
1. Application
A. Remove existing materials and obsolete penetrations
down to an acceptable substrate, repair any voids or
imperfections in the substrate.
B. For steep-slope underlayments, cut the 2-square rolls
into a minimum of 3 equal sections.
C. Unroll and allow membrane to relax in the sun for a recommended 15 minutes prior to installation in final location.
Tools
1. Trowel
2. Caulking Gun
3. Metal Head Hand Roller
4. Tape Measure
5. Utility Knives- Hook Blade, Straight Blade
1
6. Claw Hammer
7. Tin Snips
8. Hand Held Hot Air Welder
9. Silicone Hand Held Roller
2. Application
A. Measure leading edge for width of first sheet and snap straight
chalk line.
B. Lay the material flat in place, starting at the lowest point.
C. Align the membrane with chalk line at the lowest edge of
the roof.
D. Install in shingle fashion from lowest point to highest point on roof.
1
2
3
4
Accessories
1. Polyglass PG 500 TROWEL Grade Mod-Bit Adhesive –
10.3 oz cartridge
2. Polyglass PG 500 TROWEL Grade Mod-Bit Adhesive –
4.75 gal. Pail
3. Polyglass PG100 ASPHALT PRIMER – 14 oz spray Can
4. 80 lb (minimum) linoleum roller
2
08
Tools & Accessories
Applications
09
®
3. Application
5. Application
A. Fold the aligned membrane in half, exposing the dual
release film.
A. At seam overlaps, align next sheet of application, fold sheet
back and remove split release film. Remove, from the
installed roll, the protective tape, SEALLap and apply even
pressure to the self sealing SEALLap area, while overlapping
the next sheet.
B. Peel release film at a 90 degree angle in a constant motion
ensuring to keep weight on the outer edges, as you
progress. Position the next sheet by overlapping seams
and line up the overlap of the top sheet edge with the inside
of the bottom sheet’s factory selvage SEALLap edges.
Overlap and cut end laps minimum 6”.
C. This is only one example of an application technique;
contractors may develop their own methods of application.
5
6. Application
A. Roll seams and edges firmly with a steel or other suitable
roller to ensure full adhesion.
3
4. Application
A. Press the membrane into place with firm, even pressure.
6
7. Application
A. Applications on a slope greater than 2-1/2” to 12” need to be
back nailed in the seams overlap with ring shanked metal
capped roofing nails, 6” o.c.
4
10
Applications
Applications
11
®
Installation Guide
3. Application
5. Application
A. Fold the aligned membrane in half, exposing the dual
release film.
A. At seam overlaps, align next sheet of application, fold sheet
back and remove split release film. Remove, from the
installed roll, the protective tape, SEALLap and apply even
pressure to the self sealing SEALLap area, while overlapping
the next sheet.
B. Peel release film at a 90 degree angle in a constant motion
ensuring to keep weight on the outer edges, as you
progress. Position the next sheet by overlapping seams
and line up the overlap of the top sheet edge with the inside
of the bottom sheet’s factory selvage SEALLap edges.
Overlap and cut end laps minimum 6”.
C. This is only one example of an application technique;
contractors may develop their own methods of application.
5
6. Application
A. Roll seams and edges firmly with a steel or other suitable
roller to ensure full adhesion.
3
4. Application
A. Press the membrane into place with firm, even pressure.
6
7. Application
A. Applications on a slope greater than 2-1/2” to 12” need to be
back nailed in the seams overlap with ring shanked metal
capped roofing nails, 6” o.c.
4
10
Applications
Applications
11
®
9. Application
A. Details are carried out by using a hot-air welding mastic
technique or Polyglass PG 500 SBS TROWEL Grade.
B. Heat should be applied with a flameless torch or hot-air welder.
Open flame torches are not recommended.
7
8. Application
A. After adhering rolls it is required that uniform pressure be
applied to the entire sheet area by using an 80 lb
(minimum) linoleum roller, water filled lawn roller or similar
weighted roller in a method suitable to the roof slope.
Care must be taken to prevent injury when rolling
membrane, especially on sloped surfaces.
9
8
9
8
12
Applications
Applications
13
®
Installation Guide
9. Application
A. Details are carried out by using a hot-air welding mastic
technique or Polyglass PG 500 SBS TROWEL Grade.
B. Heat should be applied with a flameless torch or hot-air welder.
Open flame torches are not recommended.
7
8. Application
A. After adhering rolls it is required that uniform pressure be
applied to the entire sheet area by using an 80 lb
(minimum) linoleum roller, water filled lawn roller or similar
weighted roller in a method suitable to the roof slope.
Care must be taken to prevent injury when rolling
membrane, especially on sloped surfaces.
9
8
9
8
12
Applications
Applications
13
®
DO's
1. DO prime all concrete, masonry, metal or metallic surfaces
2.
3.
4.
5.
6.
7.
8.
9.
10.
DO apply to clean, dry, dust free surfaces
DO remove split release film at a 90 degree angle
DO roll all seams SEALLap and FASTLap to ensure 100% adhesion
DO reinforce all in/out side corners
DO back nail head laps whenever roof pitch is over 2-1/2:12
DO roll membrane when finished
DO keep material cool in summer
DO keep material warm in winter
DO sandwich all metal flashing components
ELASTOFLEX SA V Base
adhered to deck and over
nailer, below edge metal. This is
an alternative for 2 ply (or more)
systems. The starter strip method
shown in Step 1 is for one-ply
application only.
Deck
Roof nails
substrate
(staggered 4”)
2
Drip edge (fastened in
accordance with all local
building codes)
STEP 2
DON'Ts
DO NOT apply roofing membrane during inclement weather
DO NOT take ADESO roll out of box until ready to apply
DO NOT apply over shingles or similar roof coverings
DO NOT store in direct sunlight
DO NOT apply to a dirty, wet, dusty substrate
DO NOT leave out of the box overnight. Stage only a few rolls in
advance and use all rolls removed from packaging on the same day.
7. DO NOT apply in cold or wet weather or when moisture is on
deck (material substrate and ambient temperature should be at
least 40 degrees F (5 degrees C) and rising)
8. DO NOT forget to angle at 45 degrees on buried laps
9. DO NOT forget to lap 6” on granular to granular overlaps
1.
2.
3.
4.
5.
6.
TYPICAL ROOF EDGE DETAIL
ELASTOFLEX SA V starter strip cut to reqd. width, adhered to deck.
Insure the polyolefin “top film” is clean and dust free in order to
achieve the best adhesion of the following plies.
Note: For 2 or more ply systems see Step 2.
1
Deck primed with asphalt primer
(where required) - or accepted
insulation attached to deck
9-12" (may vary)
Ref. Chalk line
STEP 1
14
Do’s & Dont’s
ELASTOFLEX SA V
Strip-in 9” wide minimum, stop 1/2” from outside edge of metal
3
ELASTOFLEX SA P or POLYFLEX SA P
membrane installed over SA V Base
strip and onto primed metal.
STEP 3
Notes:
A. Factory endlaps are provided with Polyglass proprietary FASTLap
feature. These laps can be sealed in the usual way. At “BONDING
AREAS” where a seam MUST be made to the granular surface, the
following alternatives are acceptable:
Alternatives at Bonding area:
1. Granular area heated to further embed granules into SBS or APP
compound before installing subsequent flashing piece
2. Heat weld subsequent flashing seams with hot-air gun or mini-torch
3. Granular endlaps must be a 6" Mininum & FULLY ADHERED. This
can be achieved by carefully applying POLYPLUS 35 + SBS
MODIFIED TROWEL ADHESIVE in the 6” overlap area before
joining the seam surfaces
To prevent unsightly surplus adhesive on the visible area, mask the endlap
temporarily with the tape and remove when the adhesive is dry.
B. Ensure adhesion is achieved at all metal surfaces by priming with
D41 Asphalt Roof Primer and providing a 3” min. overlap.
Details
15
®
Installation Guide
DO's
1. DO prime all concrete, masonry, metal or metallic surfaces
2.
3.
4.
5.
6.
7.
8.
9.
10.
DO apply to clean, dry, dust free surfaces
DO remove split release film at a 90 degree angle
DO roll all seams SEALLap and FASTLap to ensure 100% adhesion
DO reinforce all in/out side corners
DO back nail head laps whenever roof pitch is over 2-1/2:12
DO roll membrane when finished
DO keep material cool in summer
DO keep material warm in winter
DO sandwich all metal flashing components
ELASTOFLEX SA V Base
adhered to deck and over
nailer, below edge metal. This is
an alternative for 2 ply (or more)
systems. The starter strip method
shown in Step 1 is for one-ply
application only.
Deck
Roof nails
substrate
(staggered 4”)
2
Drip edge (fastened in
accordance with all local
building codes)
STEP 2
DON'Ts
DO NOT apply roofing membrane during inclement weather
DO NOT take ADESO roll out of box until ready to apply
DO NOT apply over shingles or similar roof coverings
DO NOT store in direct sunlight
DO NOT apply to a dirty, wet, dusty substrate
DO NOT leave out of the box overnight. Stage only a few rolls in
advance and use all rolls removed from packaging on the same day.
7. DO NOT apply in cold or wet weather or when moisture is on
deck (material substrate and ambient temperature should be at
least 40 degrees F (5 degrees C) and rising)
8. DO NOT forget to angle at 45 degrees on buried laps
9. DO NOT forget to lap 6” on granular to granular overlaps
1.
2.
3.
4.
5.
6.
TYPICAL ROOF EDGE DETAIL
ELASTOFLEX SA V starter strip cut to reqd. width, adhered to deck.
Insure the polyolefin “top film” is clean and dust free in order to
achieve the best adhesion of the following plies.
Note: For 2 or more ply systems see Step 2.
1
Deck primed with asphalt primer
(where required) - or accepted
insulation attached to deck
9-12" (may vary)
Ref. Chalk line
STEP 1
14
Do’s & Dont’s
ELASTOFLEX SA V
Strip-in 9” wide minimum, stop 1/2” from outside edge of metal
3
ELASTOFLEX SA P or POLYFLEX SA P
membrane installed over SA V Base
strip and onto primed metal.
STEP 3
Notes:
A. Factory endlaps are provided with Polyglass proprietary FASTLap
feature. These laps can be sealed in the usual way. At “BONDING
AREAS” where a seam MUST be made to the granular surface, the
following alternatives are acceptable:
Alternatives at Bonding area:
1. Granular area heated to further embed granules into SBS or APP
compound before installing subsequent flashing piece
2. Heat weld subsequent flashing seams with hot-air gun or mini-torch
3. Granular endlaps must be a 6" Mininum & FULLY ADHERED. This
can be achieved by carefully applying POLYPLUS 35 + SBS
MODIFIED TROWEL ADHESIVE in the 6” overlap area before
joining the seam surfaces
To prevent unsightly surplus adhesive on the visible area, mask the endlap
temporarily with the tape and remove when the adhesive is dry.
B. Ensure adhesion is achieved at all metal surfaces by priming with
D41 Asphalt Roof Primer and providing a 3” min. overlap.
Details
15
®
SEAMING DETAIL FOR ELASTOFLEX SA P or
POLYFLEX SA P
SEAM INTERSECTION TREATMENT – FLASHINGS
PLAN VIEW OF Step 1.
1
TOP ROLL
FASTLap ROLL-END SELVAGE
PRIMED SUBSTRATE*
ELASTOFLEX SA V BASE
or OTHER ACCEPTED
BASE SHEET
45º ANGLE CUT
AT SHEET CORNERS &
POLYGLASS PG 500
OR HEAR WELD
Bonding Area
STEP 1
POLYGLASS PG 500
,
SBS MASTIC APPLIED AT
45 DEG. ANGLE CUT[S]
OR HEAT WELD
ea
PROTECTIVE SEAM TAPE SEALLap
[TO BE REMOVED PRIOR TO SEAMING]
ng
i
nd
Ar
Bo
PREVIOUSLY INSTALLED SHEET or ROLL
SEAM INTERSECTION TREATMENT – FIELD
2
45 DEG. ANGLE CUT
AT SHEET CORNERS &
POLYGLASS PG500
OR HEAT WELD
Sealant protrudes
approx 1/4"
Sequence:
A. Sheet 1 is applied to substrate.
B. Triangle piece of approx. 45º are cut off at the bottom corner of
sheet 2 (usually at the FASTLap end of the sheet) and at the top
corner of sheet 3 (the side lap selvage edge SEALLap).
C. Sheet 2 is aligned & applied to the substrate.
D. A bead of Polyglass PG 500 SBS mastic is applied at the angle
cuts (see inset) or heat weld.
E. Sheet 3 is applied.
F. Top sheet is carefully rolled parallel to both sides of the sealant
not on the sealant.
STEP 2
Provide POLYGLASS
approved detail termination, as required
by specification for
wall treatment
ELASTOFLEX SA P
field membrane
ELASTOFLEX SA V
base sheet
Approved substrate
Refer To Notes On Page15
Note:
The angle cut & seam sealant is to be applied at all self-adhered sheet
overlaps (base & cap)
16
Details
Details
17
®
Installation Guide
SEAMING DETAIL FOR ELASTOFLEX SA P or
POLYFLEX SA P
SEAM INTERSECTION TREATMENT – FLASHINGS
PLAN VIEW OF Step 1.
1
TOP ROLL
FASTLap ROLL-END SELVAGE
PRIMED SUBSTRATE*
ELASTOFLEX SA V BASE
or OTHER ACCEPTED
BASE SHEET
45º ANGLE CUT
AT SHEET CORNERS &
POLYGLASS PG 500
OR HEAR WELD
Bonding Area
STEP 1
POLYGLASS PG 500
,
SBS MASTIC APPLIED AT
45 DEG. ANGLE CUT[S]
OR HEAT WELD
ea
PROTECTIVE SEAM TAPE SEALLap
[TO BE REMOVED PRIOR TO SEAMING]
ng
i
nd
Ar
Bo
PREVIOUSLY INSTALLED SHEET or ROLL
SEAM INTERSECTION TREATMENT – FIELD
2
45 DEG. ANGLE CUT
AT SHEET CORNERS &
POLYGLASS PG500
OR HEAT WELD
Sealant protrudes
approx 1/4"
Sequence:
A. Sheet 1 is applied to substrate.
B. Triangle piece of approx. 45º are cut off at the bottom corner of
sheet 2 (usually at the FASTLap end of the sheet) and at the top
corner of sheet 3 (the side lap selvage edge SEALLap).
C. Sheet 2 is aligned & applied to the substrate.
D. A bead of Polyglass PG 500 SBS mastic is applied at the angle
cuts (see inset) or heat weld.
E. Sheet 3 is applied.
F. Top sheet is carefully rolled parallel to both sides of the sealant
not on the sealant.
STEP 2
Provide POLYGLASS
approved detail termination, as required
by specification for
wall treatment
ELASTOFLEX SA P
field membrane
ELASTOFLEX SA V
base sheet
Approved substrate
Refer To Notes On Page15
Note:
The angle cut & seam sealant is to be applied at all self-adhered sheet
overlaps (base & cap)
16
Details
Details
17
®
PGSA01_ADESO® SA RAISED EDGE METAL DETAIL
PGSA02_ADESO® SA EDGE AND GUTTER DETAIL
032 min. edge metal, by others (primed with Polyglass PG 100, ASTM D-41 primer)
Sheet metal edge flashing prime flange before stripping (required),
with Polyglass PG 100 asphalt primer
Fasten base flashing max. 8” (203 mm) O.C.
Fastener & sealing washer at min. 8” O.C. approved by metal manufacturer
Polyglass SA P CAP, flashing ply
Polyglass ELASTOFLEX SA V BASE ply sheet, set to roof edge
Set flange in Polyglass PG 500
Polyglass ELASTOFLEX SA V BASE ply flashing to cover base sheet
Multiplte-ply Polyglass SA V & SA P
roofing system plies
Fastener & stress plate, 6” O.C.
Polyglass PG 650 mastic adhesive
Fasteners at Approx. 6”
O.C., staggered
Polyglass SAP CAP sheet
Polyglass ELSTOFLEX SA V
BASE sheet
Gutter spacer alternately spaced from brackets
Roof deck
Coverboard insulation
(by others), where required.
Optional: flexible Polyglass SA
membrane closure; extend in to gutter
Wood nailers
Thermal insulation
Continuous cleat *(fastened max. 12” O.C.)
Roof Deck
Wood cant fasten to blocking
Wood Nailers (see note 1)
Continuous cleat max. 12” O.C.
Notes:
1. Attach wood nailer and edge metal to wall/deck in
accordance with ANSI/SPRI ES-1.
2. Refer to SMACNA recommendations & details regarding
metal thickness & cleat requirements.
3. Membrane endlaps must be 6” minimum & fully adhered at
all membrane in all locations where FASTLap is not present.
4. All acceptance substrates must be primed with Polyglass
PG 100 primer.
5. Thermal insulation must be of suitable type & density to
accept ADESO self-adhered membranes.
6. Mechanically attached thermal insulation is to be fastened
in accordance with insulation manufacturer’s approved
fastening pattern for project conditions.
18
Details
Continuous sheet metal closure
fastened approx. 18” 457mm O.C.
Extend one ply or a separate membrane, ELASTOFLEX SA V,
sheet to overlay metal closure mechanically attached 8” O.C. to fascia
Gutter bracket support at 12” to 24”
O.C. depending upon conditions
Sheet metal gutter
Optional: turn-down
Notes:
1. Attach wood nailer to wall/deck in accordance with ANSI/SPR1
ES-1.
2. Wood blocking may be slotted for venting of wet-fill decks or
other applicable constructions.
3. This detail should be used only where the deck is supported by
the outside wall.
4. Refer to SMACNA recommendations & details regarding metal
thickness & cleat requirements.
5. Membrane endlaps must be 6” minimum & fully adhered to all
membrane in all locations where FASTLap is not present.
*Continuous cleat is recommended to be at least one gauge
heavier than edge flashing metal.
Details
19
®
Installation Guide
PGSA01_ADESO® SA RAISED EDGE METAL DETAIL
PGSA02_ADESO® SA EDGE AND GUTTER DETAIL
032 min. edge metal, by others (primed with Polyglass PG 100, ASTM D-41 primer)
Sheet metal edge flashing prime flange before stripping (required),
with Polyglass PG 100 asphalt primer
Fasten base flashing max. 8” (203 mm) O.C.
Fastener & sealing washer at min. 8” O.C. approved by metal manufacturer
Polyglass SA P CAP, flashing ply
Polyglass ELASTOFLEX SA V BASE ply sheet, set to roof edge
Set flange in Polyglass PG 500
Polyglass ELASTOFLEX SA V BASE ply flashing to cover base sheet
Multiplte-ply Polyglass SA V & SA P
roofing system plies
Fastener & stress plate, 6” O.C.
Polyglass PG 650 mastic adhesive
Fasteners at Approx. 6”
O.C., staggered
Polyglass SAP CAP sheet
Polyglass ELSTOFLEX SA V
BASE sheet
Gutter spacer alternately spaced from brackets
Roof deck
Coverboard insulation
(by others), where required.
Optional: flexible Polyglass SA
membrane closure; extend in to gutter
Wood nailers
Thermal insulation
Continuous cleat *(fastened max. 12” O.C.)
Roof Deck
Wood cant fasten to blocking
Wood Nailers (see note 1)
Continuous cleat max. 12” O.C.
Notes:
1. Attach wood nailer and edge metal to wall/deck in
accordance with ANSI/SPRI ES-1.
2. Refer to SMACNA recommendations & details regarding
metal thickness & cleat requirements.
3. Membrane endlaps must be 6” minimum & fully adhered at
all membrane in all locations where FASTLap is not present.
4. All acceptance substrates must be primed with Polyglass
PG 100 primer.
5. Thermal insulation must be of suitable type & density to
accept ADESO self-adhered membranes.
6. Mechanically attached thermal insulation is to be fastened
in accordance with insulation manufacturer’s approved
fastening pattern for project conditions.
18
Details
Continuous sheet metal closure
fastened approx. 18” 457mm O.C.
Extend one ply or a separate membrane, ELASTOFLEX SA V,
sheet to overlay metal closure mechanically attached 8” O.C. to fascia
Gutter bracket support at 12” to 24”
O.C. depending upon conditions
Sheet metal gutter
Optional: turn-down
Notes:
1. Attach wood nailer to wall/deck in accordance with ANSI/SPR1
ES-1.
2. Wood blocking may be slotted for venting of wet-fill decks or
other applicable constructions.
3. This detail should be used only where the deck is supported by
the outside wall.
4. Refer to SMACNA recommendations & details regarding metal
thickness & cleat requirements.
5. Membrane endlaps must be 6” minimum & fully adhered to all
membrane in all locations where FASTLap is not present.
*Continuous cleat is recommended to be at least one gauge
heavier than edge flashing metal.
Details
19
®
PGSA03_ ADESO® SA BASE FLASHING DETAIL
PGSA04_ADESO® SA PARAPET CAP DETAIL
Continuous through- wall flashing (by others)
Sheet metal parapet cap (by others)
Tooled polyurethane sealant (by others)
Sheet metal reglet (by others)
Fasteners approx. 18” O.C.
Removable sheet metal counterflashing (by others)
Termination fastened 6” O.C. (required at ›18” vertical appl.)
2” (51mm) wide clip approx. 30” (762mm) O.C. (not shown for clarity)
Extension of field plies above head of cant, required (not shown for clarity)
Polyglass SA P flashing sheet adhered to Polyglass
ELASTOFLEX SA P in full bedding of Polyglass PG 500
Polyglass ELASTOFLEX SA V flashing sheet
Continuous sheet membrane liner (by others)
Wood nailer
Continuous sheet tapered wood shim
(E.G. beveled cedar siding)
Seal top of flashing with a 3-course of vertical grade roof cement and reinforcement fabric (by others), or extension of Polyglass SA
flashing plies over top of wall
Fastener & sealing washer fastened at
(approx. 18” (457mm) O.C. depending upon
wind zone and local conditions)
Termination fastened 6” O.C.
Extension of Polyglass field plies above head
of cant. Required (not shown for clarity)
Polyglass SA P flashing sheet adhered to
Polyglass ELASTOFLEX SA P in full bedding of
Polyglass PG 500 mastic.
Polyglass ELASTOFLEX SA V
flashing sheet
Polyglass PG 500 mastic
Polyglass SA P field sheet
Polyglass ELASTOFLEX SA V
Coverboard insulation,
where required
PolyglassPG 500 mastic
Polyglass SA P field sheet
Polyglass ELASTOFLEX SA V
Coverboard insulation, where required
Thermal insulation
Roof deck
Wood cant fastened to nailers
Thermal insulation
Roof deck
Wood cant fastened to nailers
Continuous cleat (see note 3)
Wood blocking mechanically fastened
Notes:
1. Acceptable masonry, metal & wood substrates must be primed
with Polyglass PG 100 asphalt primer prior to application of
ADESO self-adhered membranes.
2. Flashing plies installed over granular field sheet must be set in
full bedding of Polyglass PG 500 mastic to assure a watertight
seal over the granules or heat welded.
3. All wood blocking is to be attached per ANSI/SPRI ES-1 recommendations.
4. Thermal insulation must be of suitable type & density to accept
ADESO self-adhered membranes.
5. Metal flashing (by others) to be fabricated and installed following
NRCA & SMACNA guidelines and recommendations.
20
Details
Notes:
1. Acceptable masonry, metal & wood substrates must be primed
with Polyglass PG 100 prior to application of ADESO self-adhered
membranes.
2. Flashing plies installed over granular field sheet must be heat
seamed or set in full bedding of Polyglass PG 500 mastic to assure
a watertight seal over the granules.
3. All wood blocking to be attached per ANSI/SPRI ES-1 recommendations.
4. Thermal insulation must be of suitable type & density to accept
ADESO self-adhered membranes.
5. Metal flashing (by others) to be fabricated and installed following
NRCA & SMACNA guidelines and recommendations.
Details
21
®
Installation Guide
PGSA03_ ADESO® SA BASE FLASHING DETAIL
PGSA04_ADESO® SA PARAPET CAP DETAIL
Continuous through- wall flashing (by others)
Sheet metal parapet cap (by others)
Tooled polyurethane sealant (by others)
Sheet metal reglet (by others)
Fasteners approx. 18” O.C.
Removable sheet metal counterflashing (by others)
Termination fastened 6” O.C. (required at ›18” vertical appl.)
2” (51mm) wide clip approx. 30” (762mm) O.C. (not shown for clarity)
Extension of field plies above head of cant, required (not shown for clarity)
Polyglass SA P flashing sheet adhered to Polyglass
ELASTOFLEX SA P in full bedding of Polyglass PG 500
Polyglass ELASTOFLEX SA V flashing sheet
Continuous sheet membrane liner (by others)
Wood nailer
Continuous sheet tapered wood shim
(E.G. beveled cedar siding)
Seal top of flashing with a 3-course of vertical grade roof cement and reinforcement fabric (by others), or extension of Polyglass SA
flashing plies over top of wall
Fastener & sealing washer fastened at
(approx. 18” (457mm) O.C. depending upon
wind zone and local conditions)
Termination fastened 6” O.C.
Extension of Polyglass field plies above head
of cant. Required (not shown for clarity)
Polyglass SA P flashing sheet adhered to
Polyglass ELASTOFLEX SA P in full bedding of
Polyglass PG 500 mastic.
Polyglass ELASTOFLEX SA V
flashing sheet
Polyglass PG 500 mastic
Polyglass SA P field sheet
Polyglass ELASTOFLEX SA V
Coverboard insulation,
where required
PolyglassPG 500 mastic
Polyglass SA P field sheet
Polyglass ELASTOFLEX SA V
Coverboard insulation, where required
Thermal insulation
Roof deck
Wood cant fastened to nailers
Thermal insulation
Roof deck
Wood cant fastened to nailers
Continuous cleat (see note 3)
Wood blocking mechanically fastened
Notes:
1. Acceptable masonry, metal & wood substrates must be primed
with Polyglass PG 100 asphalt primer prior to application of
ADESO self-adhered membranes.
2. Flashing plies installed over granular field sheet must be set in
full bedding of Polyglass PG 500 mastic to assure a watertight
seal over the granules or heat welded.
3. All wood blocking is to be attached per ANSI/SPRI ES-1 recommendations.
4. Thermal insulation must be of suitable type & density to accept
ADESO self-adhered membranes.
5. Metal flashing (by others) to be fabricated and installed following
NRCA & SMACNA guidelines and recommendations.
20
Details
Notes:
1. Acceptable masonry, metal & wood substrates must be primed
with Polyglass PG 100 prior to application of ADESO self-adhered
membranes.
2. Flashing plies installed over granular field sheet must be heat
seamed or set in full bedding of Polyglass PG 500 mastic to assure
a watertight seal over the granules.
3. All wood blocking to be attached per ANSI/SPRI ES-1 recommendations.
4. Thermal insulation must be of suitable type & density to accept
ADESO self-adhered membranes.
5. Metal flashing (by others) to be fabricated and installed following
NRCA & SMACNA guidelines and recommendations.
Details
21
®
PGSA05_ADESO® SA SKYLIGHT, SCUTTLE & CURB, DETAIL
PGSA06_ADESO® SA VENT PIPE FLASHING DETAIL
Double dome skylight/hatch (by others)
Polyplus 35 premium SBS sealant
Skylight frame with weep holes
Fasteners & sealing washers at maximum
18” O.C. or as required by skylight/hatch
manufacturer
Sheet metal counterflashing (by others)
Termination fastened 6” O.C.
Extension of Polyglass field plies above head
of cant, required (not shown for clarity)
Polyglass PG 100, asphalt primer,
Polyglass PG 500 adhesive
(dependant on application method)
Flare-cut Polyglass membrane
flashing collar with “fingers”
or lead jack
Coverboard insulation, where required
Stainless steel drawband
Polyglass membrane flashing to
extend 8” min. beyond opening
Polyglass ELASTOFLEX SA P
Polyglass ELASTOFLEX SA V BASE
8” min. (TYP)
4” min. (TYP.)
Polyglass SA P flashing sheet adhered to
Polyglass ELASTOFLEX SA V in full bedding
of Polyglass PG 500
Polyglass ELASTOFLEX SA V flashing sheet
Polyglass PG 500 adhesive
Polyglass SA P field sheet
Polyglass ELASTOFLEX SA V
Coverboard insulation, where required
Thermal insulation
Roof deck
Deck
Wood cant
Rigid insulation or approved substrate
Wood nailers and curb
Notes:
1. Acceptable masonry, metal & wood substrates must be primed
with Polyglass PG 100 asphalt primer prior to application of
ADESO self-adhered membranes.
2. Flashing plies installed over granular field sheet must be heat
seamed or set in full bedding of Polyglass PG 500 adhesive to
assure a watertight seal over the granules.
3. All wood blocking to be attached per ANSI/SPRI ES-1 recommendations.
4. Thermal insulation must be of suitable type & density to accept
ADESO self-adhered membranes.
5. Metal flashing (by others) to be fabricated and installed following
NRCA & SMACNA guidelines and recommendations.
22
Details
Notes:
1.Details are carried out by using a hot-air welding technique or
Polyglass PG 500 TROWEL Grade Adhesive, in combination with
the ADESO self-adhered membranes.
Details
23
®
Installation Guide
PGSA05_ADESO® SA SKYLIGHT, SCUTTLE & CURB, DETAIL
PGSA06_ADESO® SA VENT PIPE FLASHING DETAIL
Double dome skylight/hatch (by others)
Polyplus 35 premium SBS sealant
Skylight frame with weep holes
Fasteners & sealing washers at maximum
18” O.C. or as required by skylight/hatch
manufacturer
Sheet metal counterflashing (by others)
Termination fastened 6” O.C.
Extension of Polyglass field plies above head
of cant, required (not shown for clarity)
Polyglass PG 100, asphalt primer,
Polyglass PG 500 adhesive
(dependant on application method)
Flare-cut Polyglass membrane
flashing collar with “fingers”
or lead jack
Coverboard insulation, where required
Stainless steel drawband
Polyglass membrane flashing to
extend 8” min. beyond opening
Polyglass ELASTOFLEX SA P
Polyglass ELASTOFLEX SA V BASE
8” min. (TYP)
4” min. (TYP.)
Polyglass SA P flashing sheet adhered to
Polyglass ELASTOFLEX SA V in full bedding
of Polyglass PG 500
Polyglass ELASTOFLEX SA V flashing sheet
Polyglass PG 500 adhesive
Polyglass SA P field sheet
Polyglass ELASTOFLEX SA V
Coverboard insulation, where required
Thermal insulation
Roof deck
Deck
Wood cant
Rigid insulation or approved substrate
Wood nailers and curb
Notes:
1. Acceptable masonry, metal & wood substrates must be primed
with Polyglass PG 100 asphalt primer prior to application of
ADESO self-adhered membranes.
2. Flashing plies installed over granular field sheet must be heat
seamed or set in full bedding of Polyglass PG 500 adhesive to
assure a watertight seal over the granules.
3. All wood blocking to be attached per ANSI/SPRI ES-1 recommendations.
4. Thermal insulation must be of suitable type & density to accept
ADESO self-adhered membranes.
5. Metal flashing (by others) to be fabricated and installed following
NRCA & SMACNA guidelines and recommendations.
22
Details
Notes:
1.Details are carried out by using a hot-air welding technique or
Polyglass PG 500 TROWEL Grade Adhesive, in combination with
the ADESO self-adhered membranes.
Details
23
®
PGSA07_ADESO® SA LIGHT/MEDIUM WEIGHT
EQUIPMENT CURB DETAIL
PGSA09_ADESO® ELASTOFLEX SA & POLYFLEX SA
VERTICAL WALL DETAIL
Sheet metal cover with receiver for
counterflashing (by others)
Set bolts in sealant
Polyglass acceptable fastners 6” O.C.
Fastener & sealing washer at
maximum 18” O.C. or the spacing
required by metal manufacturer
Neoprene pad
Removable sheet metal
counterflashing (by others)
Fasteners approx. 8” (203mm) O.C.
Extension of field plies above
head of cant, required (not
shown for clarity)
Wood cant fastened to
nailers
Multiple-ply Polyglass
membrane base flashing
(8” min. height) (ref. note #5)
Wood curb
Wood nailers
Details
Embed granules or use
POLYGLASS PG 500 adhesive
ELASTOFLEX SA (P)
ELASTOBASE (Poly/Sand)
or ELASTOFLEX SA V BASE
Multiple-ply Polyglass
ELASTOFLEX SA roof system
Coverboard insulation.
Where required
Thermal insulation
Roof deck
Notes:
1. Attach wood nailer to wall/ deck in accordance with FMRC
guidelines, as per section 1-28, regarding windloads to roof
systems & deck securement.
2. Wood blocking may be slotted for venting of wet-fill decks or
other applicable constructions.
3. This detail should be used only where the deck is supported
by outside wall.
4. Refer to SMACNA recommendations & details regarding metal
thickness & cleat requirements.
5. Membrane endlaps must be 6” minimum & fully adhered to all
membrane in all locations where FASTLap is not present.
24
Polyglass 2000MB+ caulk
Notes:
1. Intermittent fastening is to be at 6” O.C.
2. Maximum wall height without intermittent fastening is 24” unless
accepted in writing by Polyglass Technical Services, prior to
application.
3. All areas where salvage edge is not present shall have granules
embedded by utilizing heat, prior to overlapping.
An alternative application is to use Polyglass POLYPLUS 35 cold adhesive.
Details
25
Installation Guide
®
PGSA07_ADESO® SA LIGHT/MEDIUM WEIGHT
EQUIPMENT CURB DETAIL
PGSA09_ADESO® ELASTOFLEX SA & POLYFLEX SA
VERTICAL WALL DETAIL
Sheet metal cover with receiver for
counterflashing (by others)
Set bolts in sealant
Polyglass acceptable fastners 6” O.C.
Fastener & sealing washer at
maximum 18” O.C. or the spacing
required by metal manufacturer
Neoprene pad
Removable sheet metal
counterflashing (by others)
Fasteners approx. 8” (203mm) O.C.
Extension of field plies above
head of cant, required (not
shown for clarity)
Wood cant fastened to
nailers
Multiple-ply Polyglass
membrane base flashing
(8” min. height) (ref. note #5)
Wood curb
Wood nailers
Details
Embed granules or use
POLYGLASS PG 500 adhesive
ELASTOFLEX SA (P)
ELASTOBASE (Poly/Sand)
or ELASTOFLEX SA V BASE
Multiple-ply Polyglass
ELASTOFLEX SA roof system
Coverboard insulation.
Where required
Thermal insulation
Roof deck
Notes:
1. Attach wood nailer to wall/ deck in accordance with FMRC
guidelines, as per section 1-28, regarding windloads to roof
systems & deck securement.
2. Wood blocking may be slotted for venting of wet-fill decks or
other applicable constructions.
3. This detail should be used only where the deck is supported
by outside wall.
4. Refer to SMACNA recommendations & details regarding metal
thickness & cleat requirements.
5. Membrane endlaps must be 6” minimum & fully adhered to all
membrane in all locations where FASTLap is not present.
24
Polyglass 2000MB+ caulk
Notes:
1. Intermittent fastening is to be at 6” O.C.
2. Maximum wall height without intermittent fastening is 24” unless
accepted in writing by Polyglass Technical Services, prior to
application.
3. All areas where salvage edge is not present shall have granules
embedded by utilizing heat, prior to overlapping.
An alternative application is to use Polyglass POLYPLUS 35 cold adhesive.
Details
25
®
PGSA15_ADESO® SA BASE FLASHING PARAPET
WALL - 2PLY DETAIL
Notes:
Flashing membranes to be set in bed of Polyglass PG 500 or
approved equal, modified asphalt adhesive (trowel grade)
PGSA16_ADESO® SA CLOSED VALLEY FLASHING
DETAIL
Lap joint set in bed of Polyglass PG 500 + (trowel grade) mod. bit. Adhesive
“L” metal flashing, by others (set in mastic)
Wall siding, by others
Polyglass SA CAP membrane
ELASTOFLEX SA V BASE
.
d)
min
12” dge en
ee
g
a
lv
(se
Polyglass
ELASTOFLEX SA P
flashing membrane
Polyglass ELASTOFLEX SA V
flashing membrane
ELASTOFLEX SA V BASE
m
imu f
min
o
18” width A V)
S
(half FLEX
O
T
S
A
L
E
Approved substrate
Polyglass ELASTOFLEX SA P
Polyglass ELASTOFLEX SA V
BASE
Primed substrate (see note 3) mechanically fastened,
per specification
Existing substrate
Notes:
Notes:
1. Refer to SMACNA recommendations & details regarding
metal thickness & cleat requirements.
2. Membrane endlaps must be 6” minimum & fully adhered to
all membrane in all locations where FASTLap is not
present.
3. Polyglass USA requires all metal surfaces to be cleaned
and primed with Polyglass PG 100 asphalt primer or an
ASTM #D-41 equal.
1. Closed valley to be lined with ELASTOFLEX SA V BASE and
an ADESO self-adhered CAP sheets to run parallel through
the valley.
2. Finish membranes to overlay flashing membrane creating
the closed valley, overlap joints, which occur over
granulated materials, are to be set in bed of Polyglass PG
500 or approved trowel grade, modified asphalt adhesive.
3. Valleys can be lined using the Polyglass header roll or metal
flashing by others, consult Polyglass Technical Services at
(866) 802-8017 for such applications.
Details
26
Details
Details
27
®
Installation Guide
PGSA15_ADESO® SA BASE FLASHING PARAPET
WALL - 2PLY DETAIL
Notes:
Flashing membranes to be set in bed of Polyglass PG 500 or
approved equal, modified asphalt adhesive (trowel grade)
PGSA16_ADESO® SA CLOSED VALLEY FLASHING
DETAIL
Lap joint set in bed of Polyglass PG 500 + (trowel grade) mod. bit. Adhesive
“L” metal flashing, by others (set in mastic)
Wall siding, by others
Polyglass SA CAP membrane
ELASTOFLEX SA V BASE
.
d)
min
12” dge en
ee
g
a
lv
(se
Polyglass
ELASTOFLEX SA P
flashing membrane
Polyglass ELASTOFLEX SA V
flashing membrane
ELASTOFLEX SA V BASE
m
imu f
min
o
18” width A V)
S
(half FLEX
O
T
S
A
L
E
Approved substrate
Polyglass ELASTOFLEX SA P
Polyglass ELASTOFLEX SA V
BASE
Primed substrate (see note 3) mechanically fastened,
per specification
Existing substrate
Notes:
Notes:
1. Refer to SMACNA recommendations & details regarding
metal thickness & cleat requirements.
2. Membrane endlaps must be 6” minimum & fully adhered to
all membrane in all locations where FASTLap is not
present.
3. Polyglass USA requires all metal surfaces to be cleaned
and primed with Polyglass PG 100 asphalt primer or an
ASTM #D-41 equal.
1. Closed valley to be lined with ELASTOFLEX SA V BASE and
an ADESO self-adhered CAP sheets to run parallel through
the valley.
2. Finish membranes to overlay flashing membrane creating
the closed valley, overlap joints, which occur over
granulated materials, are to be set in bed of Polyglass PG
500 or approved trowel grade, modified asphalt adhesive.
3. Valleys can be lined using the Polyglass header roll or metal
flashing by others, consult Polyglass Technical Services at
(866) 802-8017 for such applications.
Details
26
Details
Details
27
®
PGSA17_ADESO ® SA TIE IN JOINT FLASHING
DETAIL
Residential roofing system, by others
Fastener at 6” O.C.
if over 2.5 : 12
6” Lap set in bed of
Polyglass PG 500 adhesive
(se
Polyglass SA cap,
finish membrane
ELASTOFLEX SA V BASE
membrane to membrane seams, and 3” minimum where
overlapped and adhered to a primed metal surface.
PGSA23_ADESO® SA INSIDE CORNER FLASHING
DETAIL
.
d)
min
12” dge en
ee
g
a
lv
6” min
Notes:
1. Membrane end laps must be a minimum 6” & fully adhered at all
Vertical wall
Polyglass PG 100
asphalt primer 8or
ASTM D-41 equal
m
imu f
min
o
18” width A V)
S
(half FLEX
O
T
S
ELA
See note 1
Approved substrate
Notes:
1. ADESO Polyflex SAP or Elastoflex SAP membrane to tie in
under residential roofing system, Polyglass recommends
sealing tie in with bed of Polyglass PG 500 or approved
trowel grade modified asphalt adhesive.
PGSA22_ADESO® SA OUTSIDE CORNER FLASHING
DETAIL
Vertical wall
Polyglass
membrane flashing
Polyglass reinforcing
membrane
corner piece
Polyglass SA CAP
field membrane
(2) layers Polyglass
ELASTOFLEX SA V
BASE ply
Fire retardant cant
strip req. (covered
with base sheet)
Polyglass PG 100
asphalt primer (TYP)
1,5” min. rigid
insulation 8or
approved substrate)
Polyglass
flashing pieces turned around wall end
Deck
Polyglass self adhered
membrane & baseplys
turned up wall over cant
min 6” vertical height
Polyglass reinforcing
membrane corner pieces
Polyglass
ELASTOFLEX SA P
field membrane
Notes:
1. Membrane end laps must be a minimum 6” and fully adhered at
all membrane to membrane seams and a minimum 3” where
overlapped and adhered to primed metal surface.
(2) layers Polyglass
ELASTOFLEX SA V
BASE ply
1.5” min rigid
insulation
(or approved
substrate)
Deck
28
Details
Details
29
®
Installation Guide
PGSA17_ADESO ® SA TIE IN JOINT FLASHING
DETAIL
Residential roofing system, by others
Fastener at 6” O.C.
if over 2.5 : 12
6” Lap set in bed of
Polyglass PG 500 adhesive
(se
Polyglass SA cap,
finish membrane
ELASTOFLEX SA V BASE
membrane to membrane seams, and 3” minimum where
overlapped and adhered to a primed metal surface.
PGSA23_ADESO® SA INSIDE CORNER FLASHING
DETAIL
.
d)
min
12” dge en
ee
g
a
lv
6” min
Notes:
1. Membrane end laps must be a minimum 6” & fully adhered at all
Vertical wall
Polyglass PG 100
asphalt primer 8or
ASTM D-41 equal
m
imu f
min
o
18” width A V)
S
(half FLEX
O
T
S
ELA
See note 1
Approved substrate
Notes:
1. ADESO Polyflex SAP or Elastoflex SAP membrane to tie in
under residential roofing system, Polyglass recommends
sealing tie in with bed of Polyglass PG 500 or approved
trowel grade modified asphalt adhesive.
PGSA22_ADESO® SA OUTSIDE CORNER FLASHING
DETAIL
Vertical wall
Polyglass
membrane flashing
Polyglass reinforcing
membrane
corner piece
Polyglass SA CAP
field membrane
(2) layers Polyglass
ELASTOFLEX SA V
BASE ply
Fire retardant cant
strip req. (covered
with base sheet)
Polyglass PG 100
asphalt primer (TYP)
1,5” min. rigid
insulation 8or
approved substrate)
Polyglass
flashing pieces turned around wall end
Deck
Polyglass self adhered
membrane & baseplys
turned up wall over cant
min 6” vertical height
Polyglass reinforcing
membrane corner pieces
Polyglass
ELASTOFLEX SA P
field membrane
Notes:
1. Membrane end laps must be a minimum 6” and fully adhered at
all membrane to membrane seams and a minimum 3” where
overlapped and adhered to primed metal surface.
(2) layers Polyglass
ELASTOFLEX SA V
BASE ply
1.5” min rigid
insulation
(or approved
substrate)
Deck
28
Details
Details
29
®
PGSA32_ADESO ® SA ROOF DRAIN DETAIL –
ALTERNATE
Drain strainer
Cast iron clamping ring
30” square minimum, lead or 16 oz.
copper flashing set in tooled Polyglass
PG 500 + sealant prime top surface
before stripping
Polyglass ELASTOFLEX SA
roofing membranes
(2 plies, SA V + 1 ply SA P)
Polyglass SA multiple-ply
roof membrane system
SURFACE PREPARATION & PRECAUTIONS
ADESO self-adhered membranes are to be applied directly
to approved insulations, Polyglass base sheets, and roof
decks. Do not apply to shingles, shakes or other residential
finished roof coverings.
1. Apply only when the weather is dry and all material
interface temperatures (air, roof deck, membrane) are 40
degrees F (5 degrees C) and rising. Roofing installation
shall not be conducted when water is in any form i.e. rain,
dew, ice, frost, snow. Use of hot air gun or SBS cold
adhesive, may be required under low temperature conditions.
Tapered insulation
ELASTOFLEX SA P
membrane field plies, metal
flashing and stripping plies
all extend under clamping ring
Roof deck
Thermal insulation
Drain bowl
Under deck clamp
Coverboard insulation, where required
Notes:
1. Attach wood nailer to wall/deck in accordance with
ANSI/SPRI ES-1.
2. Wood blocking may be slotted for venting of wet-fill decks
or other applicable constructions.
3. This detail should be used only where the deck is supported
by the outside wall.
4. Refer to SMACNA recommendations & details regarding
metal thickness & cleat requirements.
5. Membrane endlaps must be 6” minimum & fully adhered to
all membrane in all locations where FASTLap is not present.
STORAGE
ADESO self-adhered membranes should be stored at room
temperature whenever possible. Avoid storing out of the box
for prolonged periods. Do not take the roll out of the box
until it is ready for application. Do not store unpacked roll in
direct sunlight and in bright sunshine or in hot weather.
Removal of release film may cause static electricity
discharge.
30
Details | General Recommendations
2. All roof deck application areas shall have positive
drainage, continuous support and structurally sound to
support the live and dead load requirements of the roofing
system and sufficiently rigid to support construction traffic.
3. Apply only over clean, dry and dust-free surfaces. For
best results, wood, concrete, masonry, metal or metallic
surfaces and acceptable smooth surface BUR and other
acceptable substrates are to be primed with Polyglass PG
100 Asphalt Roof Primer prior to the application of the
membrane. The primed substrate should be fully dry prior
to installation.
4. Masonry or concrete supported by steel frame or other
steel structure shall be provided with suitable expansion
joint designs and detailed for movement.
5. Ensure that installation of any ADESO self-adhered
product does not prevent or interfere with ventilation of
existing construction.
General Recommendations
31
Installation Guide
®
PGSA32_ADESO ® SA ROOF DRAIN DETAIL –
ALTERNATE
Drain strainer
Cast iron clamping ring
30” square minimum, lead or 16 oz.
copper flashing set in tooled Polyglass
PG 500 + sealant prime top surface
before stripping
Polyglass ELASTOFLEX SA
roofing membranes
(2 plies, SA V + 1 ply SA P)
Polyglass SA multiple-ply
roof membrane system
SURFACE PREPARATION & PRECAUTIONS
ADESO self-adhered membranes are to be applied directly
to approved insulations, Polyglass base sheets, and roof
decks. Do not apply to shingles, shakes or other residential
finished roof coverings.
1. Apply only when the weather is dry and all material
interface temperatures (air, roof deck, membrane) are 40
degrees F (5 degrees C) and rising. Roofing installation
shall not be conducted when water is in any form i.e. rain,
dew, ice, frost, snow. Use of hot air gun or SBS cold
adhesive, may be required under low temperature conditions.
Tapered insulation
ELASTOFLEX SA P
membrane field plies, metal
flashing and stripping plies
all extend under clamping ring
Roof deck
Thermal insulation
Drain bowl
Under deck clamp
Coverboard insulation, where required
Notes:
1. Attach wood nailer to wall/deck in accordance with
ANSI/SPRI ES-1.
2. Wood blocking may be slotted for venting of wet-fill decks
or other applicable constructions.
3. This detail should be used only where the deck is supported
by the outside wall.
4. Refer to SMACNA recommendations & details regarding
metal thickness & cleat requirements.
5. Membrane endlaps must be 6” minimum & fully adhered to
all membrane in all locations where FASTLap is not present.
STORAGE
ADESO self-adhered membranes should be stored at room
temperature whenever possible. Avoid storing out of the box
for prolonged periods. Do not take the roll out of the box
until it is ready for application. Do not store unpacked roll in
direct sunlight and in bright sunshine or in hot weather.
Removal of release film may cause static electricity
discharge.
30
Details | General Recommendations
2. All roof deck application areas shall have positive
drainage, continuous support and structurally sound to
support the live and dead load requirements of the roofing
system and sufficiently rigid to support construction traffic.
3. Apply only over clean, dry and dust-free surfaces. For
best results, wood, concrete, masonry, metal or metallic
surfaces and acceptable smooth surface BUR and other
acceptable substrates are to be primed with Polyglass PG
100 Asphalt Roof Primer prior to the application of the
membrane. The primed substrate should be fully dry prior
to installation.
4. Masonry or concrete supported by steel frame or other
steel structure shall be provided with suitable expansion
joint designs and detailed for movement.
5. Ensure that installation of any ADESO self-adhered
product does not prevent or interfere with ventilation of
existing construction.
General Recommendations
31
®
Installation Guide
for Self-Adhered Membranes
Hazleton, Pennsylvania 18202
Phone (570) 384-1230 - Fax (570) 384-3282
Toll Free (800) 894-4563
Winter Haven, Florida 33880
Phone (863) 297-5800 - Fax (863) 618-2193
Toll Free (866) 802-8017
4ADESO1 - 02/11 - 10,000- InnerWorkings
Manufacturing Facilities
Fernley, Nevada 89408
Phone (775) 575-6007 - Fax (775) 575-2314
Toll Free (800) 222-9782
ww w.po lygla ss. co m
POLYGLASS® USA, Inc.
Corporate Office
1111 West Newport Center Drive
Deerfield Beach, Florida 33442
Phone (954) 233-1330 - Fax (954) 418-4453
Toll Free (888) 410-1375
e-mail: pgmarketing@polyglass.com