Lytespan® Track Lighting
Page 1 of 2
6273B
Sof-Tech® Low Voltage Enclosed Spot MR16
5
4
6
3
3 3/ 8 "
Pivot
10
2
3 3/ 4 "
4 5/ 8 "
9
2 5/ 8 "
1
8
4 5/ 8 "
7
2 1/ 4 "
Ordering Information
Catalog No. Finishes
Track Mountings
Lamps
6273B WH
6273B BK
6273B AL
All Lytespan Track
Systems
MR16 50W Max.
Matte White
Matte Black
Metallic Aluminum
Features
Electrical/Dimming
1. Ring: Die-cast aluminum with cool grip insulation band, a high temperature
silicone rubber which allows aiming adjustments while fixture is on.
2. Socket: Bi-pin ceramic socket wired with 18 ga. stranded Teflon leads with
fiberglass outer sleeve.
3. Transformer: Electronic low voltage transformer with integral radio
frequency interference filter and anti-crossover circuit for increased
reliability; housed in extruded aluminum.
4. Track Attachment Fitting: Molded polycarbonate, rotates into track and
locks on with push tab; integral polarity key guard.
5. Push Tab: Locks and detaches unit from track.
6. Brass Contacts: Extends for connection to second circuit in Advent®
Lytespan track.
7. Tension Pivot Mounts: Die-cast aluminum. Allows for 180° horizontal
rotation and 180° vertical rotation.
8. Lamp Guard: Tempered glass.
9. Spring: Steel springs hold lamp and housing in place.
10. Housing: Aluminum, fully encloses lamp back and socket. Vents dissipate
lamp heat.
Dimming controls: Use only dimmers specifically designed for use with
electronic transformers, like Lightolier SunriseTM and Neptune Momentum QETM
series. Low voltage fixtures may produce audible sound when used with
dimmers, which may be objectionable in acoustically critical areas.
Options & Accessories
Accessory Holder
2” Dia. Series
7662
Lenses and Louver
Labels
UL; Patent Pending
Job Information
Type:
Job Name:
Cat. No.:
Lamp(s):
Notes:
Lightolier a Genlyte Thomas Company
www.lightolier.com
631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710
We reserve the right to change details of design, materials and finish.
© 2002 Genlyte Thomas Group LLC (Lightolier Division) • A0902
6273B
Lytespan® Track Lighting
Page 2 of 2
Sof-Tech® Low Voltage Enclosed Spot MR16
Lighting Data
Aiming Angle
L
W
C
D
A
FC
0˚
30˚, 45˚ or 60˚ Horizontal
D
Beam Length
Beam Width
Distance to center beam
Distance
Aiming Angle
Footcandles
A
C
D
D
FC L
A
L and W are the outer points where the candle
power drops to 50% of the maximum. FC are the
initial footcandles at the center of the beam.
L
LAMP
30˚, 45˚ or 60˚ Vertical
FC
FC
W
L
0˚ AIMING ANGLE
A=30˚ AIMING ANGLE
W
C
A=45˚ AIMING ANGLE
Job Information
A=60˚ AIMING ANGLE
Type:
Lightolier a Genlyte Thomas Company
www.lightolier.com
631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710
We reserve the right to change details of design, materials and finish.
© 2002 Genlyte Thomas Group LLC (Lightolier Division) • A0902
Y
READAND UNDERSTAND THESE INSTRUCTIONS BEFOREINSTALLING FIXTURE
“his fixture is intended for installation in accordance with the National Electrical Code and local regulations.
“oassure full compliance with local codes and regulations, check with your local electrical inspector before
mtallation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
b
INSTRUCTIONS
INSTRUCTIONS
INSTRUCTION SHEET NO.
IS:6273
1094
Page 1 of 2
FOR ATTACHING SOF-TECH” LOW VOLTAGE TO LYTESPAN”
FOR USE WITH LYTESPANiTRACK SYSTEMS ONLY
FOR ATTACHING
SOF-TECH”
TRACK
LOW VOLTAGE TO SINGLE CIRCUIT TRACK SYSTEM
1. Insert into LYTESPAN TRACK (see Fig. 1). LOCKING I-EVER must be in same side of track as BEAD.
2. Rotate FllllNG
90” clockwise (see Fig. 2).
3. Rotate FITTING until LOCKING LEVER snaps and locks in place (see Fig. 3).
4. To remove: depress LOCKING LEVER, then rotate FITTING 90” counterclockwise.
~=_=&;_Q/-’’’’’’~~TRACK
‘-%2
r
—
BEAD
45
~}1
Ii-.
~;~p,,
., Fi
—_—_–:=
.4–,’:,
\, ,:\yil
.;.
-~
~
== — d
“
i---:--+
1-””
LOCKING1
LEVER
‘“-
~ 1.,
\,,,—
-.
.-’
J
TO
REMOVE
[!
INSTRUCTIONS
ATTACHMENT
FIG.3
FIG.2
FIG.1
FOR CONVERTING SOF-TECH@ LOW VOLTAGE
FITTING TO OPERATE ON 2 CIRCUIT TRACK
(See Fig. 4) BRASS CONTACT can be raised or lowered. Broken line indicates position
for 1 circuit track system or lower circuit of 2 circuit track system.
To convert attachment FITTING for upper circuit of. 2 circuit track, raised BRASS
CONTACT to high position by lifting CONTACT as high as stop permits and CONTACT
clicks into place.
.,,
BRASS CONTACT
./>
q-
*L
(~’,
G-
&:.;=s
,,=LOCKING
LEVER
[1
SEE BACK FOR LAMPING
w—FIG.4
@
1E 1? MONTREAL,
QUEBEC
CANADA
FALL RIVER, MASSACHUSETTS,
M
c>
H
Tcx
02720
d
I
INSTRUCTION
SHEET NO.
INSTRUCTIONS
FOR LAMPING AND
ADJUSTING SOF-TECH@ LOW VOLTAGE
1S:6273
-----
1094
_..
Page z or z
1. Check to see that power is OFF when Iamping or relamping.
2. For 6273B insert the two I-AMP PINS into the SOCKET HOLES (Fig. 5a);
For 6273T insert the two LAMP STUDS into the SOCKET HOLES and
twist clockwise (Fig. 5b).
3. Insert COVER with LAMP into RING until (3) LAMP SPRINGS engage
fully with the RING (Fig. 6).
(- ‘-’)
SOCKETHOLES
4. To aim fixture, rotate as shown (Fig. 7)
—
,.
@
—
k
t“q-
FIG.5b
(6273T)
FIG.5a
(6273b)
C-Eg$il
“1“y
L..
&..__&[.
(cc
. ..[+]-
RING
A. . ..—.
..g
———
/<
6
~T:
,/
~
LAMP GLASS SHIELD
(WITH 6273B ONLY)
=>.
-.
‘“
\:__
-
-...,
.<__ /.
..__ .__-:/’
——
—1
.:=-—
1
.-—
LAMP SPRING
FIG.6
r
180”
VERTICAL
ROTATION
0“
v“
FIG.7
HORIZONTAL
ROTATION
180”
d