TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
•
•
•
•
•
TLC2202B Is 100% Tested for Noise
30 nV/√Hz Max at f = 10 Hz
12 nV/√Hz Max at f = 1 kHz
Low Input Offset Voltage . . . 500 µV Max
Excellent Offset Voltage Stability
With Temperature . . . 0.5 µV/°C Typ
•
Rail-to-Rail Output Swing
Low Input Bias Current
1 pA Typ at TA = 25°C
Common-Mode Input Voltage Range
Includes the Negative Rail
description
TYPICAL EQUIVALENT
INPUT NOISE VOLTAGE
vs
FREQUENCY
The TLC2202, TLC2202A, TLC2202B, and
TLC2202Y are precision, low-noise operational
amplifiers using Texas Instruments Advanced
LinCMOS process. These devices combine the
noise performance of the lowest-noise JFET
amplifiers with the dc precision available
previously only in bipolar amplifiers. The
Advanced LinCMOS process uses silicon-gate
technology to obtain input offset voltage stability
with temperature and time that far exceeds that
obtainable using metal-gate technology. In
addition, this technology makes possible input
impedance levels that meet or exceed levels
offered by top-gate JFET and expensive
dielectric-isolated devices.
V n – Equivalent Input Noise Voltage – nV/ Hz
Hz
Vn
60
The combination of excellent dc and noise
performance with a common-mode input voltage
range that includes the negative rail makes these
devices an ideal choice for high-impedance,
low-level signal-conditioning applications in either
single-supply or split-supply configurations.
VDD = 5 V
RS = 20 Ω
TA = 25°C
50
40
30
20
10
0
1
10
100
1k
10 k
f – Frequency – Hz
The device inputs and outputs are designed to withstand – 100-mA surge currents without sustaining latch-up.
In addition, internal ESD-protection circuits prevent functional failures at voltages up to 2000 V as tested under
MIL-STD-883C, Method 3015.2; however, care should be exercised in handling these devices as exposure to
ESD may result in degradation of the parametric performance.
AVAILABLE OPTIONS
PACKAGED DEVICES
TA
VIOmax
AT 25°C
Vnmax
f = 10 Hz
AT 25°C
Vnmax
f = 1 kHz
AT 25°C
0°C to 70°C
500 µV
500 µ
µV
1 mV
30 nV/√Hz
35 nV/√Hz
—
– 40°C to 85°C
500 µV
500 µ
µV
1 mV
– 55°C to 125°C
500 µV
500 µ
µV
1 mV
CHIP
FORM
(Y)
SMALL
OUTLINE
(D)
CHIP
CARRIER
(FK)
CERAMIC
DIP
(JG)
PLASTIC
DIP
(P)
12 nV/√Hz
15 nV/√Hz
—
TLC2202BCD
TLC2202ACD
TLC2202CD
—
—
—
—
—
—
TLC2202BCP
TLC2202ACP
TLC2202CP
TLC2202Y
30 nV/√Hz
35 nV/√Hz
—
12 nV/√Hz
15 nV/√Hz
—
TLC2202BID
TLC2202AID
TLC2202ID
—
—
—
—
—
—
TLC2202BIP
TLC2202AIP
TLC2202IP
—
30 nV/√Hz
35 nV/√Hz
—
12 nV/√Hz
15 nV/√Hz
—
TLC2202BMD
TLC2202AMD
TLC2202MD
TLC2202BMFK
TLC2202AMFK
TLC2202MFK
TLC2202BMJG
TLC2202AMJG
TLC2202MJG
TLC2202BMP
TLC2202AMP
TLC2202MP
—
The D packages are available taped and reeled. Add R suffix to device type (e.g. TLC2202BCDR). Chips are tested at 25°C.
Advanced LinCMOS is a trademark of Texas Instruments Incorporated.
Copyright  1994, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
On products compliant to MIL-STD-883, Class B, all parameters are
tested unless otherwise noted. On all other products, production
processing does not necessarily include testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
description (continued)
The C-suffix devices are characterized for operation from 0°C to 70°C. The I-suffix devices are characterized
for operation from – 40 °C to 85°C. The M-suffix devices are characterized for operation over the full military
temperature range of – 55°C to 125°C.
1
14
2
13
3
12
4
11
5
10
6
9
7
8
NC
NC
VDD +
2OUT
2IN –
2IN +
NC
JG OR P PACKAGE
(TOP VIEW)
NC
1IN –
NC
1IN +
NC
4
3 2 1 20 19
18
5
17
6
16
7
15
8
14
9 10 11 12 13
1OUT
1IN –
1IN +
VDD – /GND
NC
2OUT
NC
2IN –
NC
1
8
2
7
3
6
4
5
VDD +
2OUT
2IN –
2IN +
NC
VDD – /GND
NC
2IN+
NC
NC
NC
1OUT
1IN –
1IN +
VDD – /GND
NC
FK PACKAGE
(TOP VIEW)
NC
1OUT
NC
VDD+
NC
D PACKAGE
(TOP VIEW)
NC – No internal connection
equivalent schematic (each amplifier)
VDD +
Q3
Q6
Q9
Q12
Q14
Q16
IN +
OUT
C1
IN –
Q1
Q4
Q13
Q15
Q17
D1
Q7
Q8
Q10
Q11
R1
Q2
Q5
VDD – / GND
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
R2
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
TLC2202Y chip formation
This chip, when properly assembled, displays characteristics similar to the TLC2202C. Thermal compression
or ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with
conductive epoxy or a gold-silicon preform.
BONDING PAD ASSIGNMENTS
(8)
(7)
(6)
1IN +
(3)
(2)
1IN –
(5)
(7)
VDD+
(8)
+
(1)
1OUT
–
+
2OUT
–
(5)
(6)
2IN +
2IN –
(4)
80
VDD–
CHIP THICKNESS: 15 TYPICAL
BONDING PADS: 4 × 4 MINIMUM
TJmax = 150°C
(4)
TOLERANCES ARE ± 10%.
ALL DIMENSIONS ARE IN MILS.
(1)
(2)
(3)
PIN (4) IS INTERNALLY CONNECTED
TO BACKSIDE OF CHIP.
100
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VDD + (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 V
Supply voltage, VDD – . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 8 V
Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 16 V
Input voltage, VI (any input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 8 V
Input current, II (each input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 5 mA
Output current, IO (each output) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 50 mA
Duration of short-circuit current at (or below) 25°C (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . unlimited
Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range, TA: C suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
I suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 85°C
M suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 55°C to 125°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
Case temperature for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D or P package . . . . . . . . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: JG package . . . . . . . . . . . . . . . . . . . . 300°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values except differential voltages are with respect to the midpoint between VDD + and VDD – .
2. Differential voltages are at IN+ with respect to IN –.
3. The output may be shorted to either supply. Temperature and /or supply voltages must be limited to ensure that the maximum
dissipation rating in not exceeded.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25
25°C
C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70
70°C
C
POWER RATING
TA = 85
85°C
C
POWER RATING
TA = 125
125°C
C
POWER RATING
D
950 mW
7.6 mW/°C
608 mW
494 mW
190 mW
FK
1375 mW
11.0 mW/°C
880 mW
715 mW
275 mW
JG
1050 mW
8.4 mW/°C
672 mW
546 mW
210 mW
P
1000 mW
8.0 mW/°C
640 mW
520 mW
200 mW
recommended operating conditions
C SUFFIX
MIN
Supply voltage, VDD ±
Common-mode input voltage, VIC
Operating free-air temperature, TA
4
MAX
± 2.3
VDD –
0
±8
VDD + – 2.3
70
POST OFFICE BOX 655303
I SUFFIX
MIN
± 2.3
VDD –
– 40
• DALLAS, TEXAS 75265
MAX
±8
VDD + – 2.3
85
M SUFFIX
MIN
± 2.3
VDD –
– 55
MAX
±8
VDD + – 2.3
125
UNIT
V
V
°C
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless otherwise specified)
PARAMETER
VIO
αVIO
TEST CONDITIONS
Temperature coefficient of input offset voltage
RS = 50 Ω
VIC = 0
0,
Input offset current
RS = 50 Ω
VIC = 0
0,
IIB
Input bias current
RS = 50 Ω
C
Common-mode
d input
i p voltage
l g range
g
VOM +
Maximum positive peak output voltage swing
RL = 10 kΩ
AVD
TYP
MAX
100
1000
Full range
1150
Full range
0.001
25°C
0.5
Full range
Maximum negative peak output voltage swing
L
i
l diff
differential
i l voltage
l
amplification
lifi i
Large-signal
VO = ± 4 V,
RL = 500 kΩ
VO = ± 4 V,
RL = 10 kΩ
CMRR
Common-mode rejection ratio
VO = 0,
RS = 50 Ω
VIC = VICRmin,
kSVR
Supply-voltage rejection ratio (∆VDD ± /∆VIO)
2 3 V to ± 8 V
VDD ± = ± 2.3
IDD
Supply current
VO = 0
0,
No load
0.005
100
25°C
UNIT
µV
µV/°C
0.5
25°C
1
Full range
VICR
VOM –
TLC2202C
MIN
25°C
Input offset voltage
Input offset voltage long-term drift (see Note 4)
IIO
TA†
µV/mo
pA
A
100
F ll range
Full
g
–5
to
2.7
25°C
4.7
Full range
4.7
25°C
– 4.7
Full range
– 4.7
25°C
300
Full range
200
25°C
50
Full range
25
25°C
80
Full range
80
25°C
80
Full range
80
25°C
V
4.8
V
– 4.9
V
560
V/ V
V/mV
100
115
dB
110
1.8
Full range
dB
2.7
2.7
mA
† Full range is 0°C to 70°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150 °C extrapolated
to TA = 25 °C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
operating characteristics at specified free-air temperature, VDD± = ±5 V
PARAMETER
TEST CONDITIONS
VO = ± 2.3 V,
CL = 100 pF
SR
Slew rate at unity gain
Vn
Equivalent input noise voltage
VN(PP)
Peak-to-peak equivalent input noise voltage
In
Equivalent input noise current
Gain-bandwidth product
φm
Phase margin at unity gain
† Full range is 0°C to 70°C.
RL = 10 kΩ,
TA†
TLC2202C
MIN
TYP
25°C
1.8
2.7
Full range
1.3
MAX
UNIT
V/µs
f = 10 Hz
25°C
18
f = 1 kHz
25°C
8
f = 0.1 to 1 Hz
25°C
0.5
f = 0.1 to 10 Hz
25°C
0.7
25°C
0.6
fA/√Hz
25°C
19
1.9
MHz
25°C
48°
f = 10 kHz,
CL = 100 pF
RL = 10 kΩ,
RL = 10 kΩ,
CL = 100 pF
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
nV/√Hz
µV
5
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, VDD ± = ±5 V (unless otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature
coefficient
p
of input offset voltage
TEST CONDITIONS
25°C
0
VIC = 0,
RS = 50 Ω
Input bias current
VICR
Common-mode input
voltage range
VOM +
Maximum p
positive p
peak
output voltage swing
VOM –
AVD
Maximum negative
g
p
peak
output voltage swing
Large-signal
differential
L g ig l diff
i l
voltage amplification
Full range
MAX
80
500
RS = 50 Ω
RL = 10 kΩ
VO = ± 4 V
V,
VO = ± 4 V
V,
RL = 500 kΩ
RL = 10 kΩ
CMRR
Common-mode rejection ratio
VIC = VICRmin,,
VO = 0,
RS = 50 Ω
kSVR
Supply-voltage
pp y
g rejection
j
ratio
(∆VDD ± /∆VIO)
VDD ± = ± 2.3
2 3 V to ± 8 V
IDD
Supply current
VO = 0
0,
No load
TYP
MAX
80
500
650
0.001 0.005
0.001 0.005
0.5
0.5
Full range
100
25°C
100
1
1
100
Full
g
F ll range
–5
to
2.7
25°C
4.7
Full range
4.7
25°C
– 4.7
Full range
– 4.7
25°C
300
Full range
200
25°C
50
Full range
25
25°C
80
Full range
80
25°C
80
Full range
80
25°C
100
–5
to
2.7
4.8
4.7
– 4.7
4.8
300
– 4.9
50
pA
pA
V
560
200
100
µV/mo
V
– 4.7
560
µV
V
4.7
– 4.9
UNIT
µV/°C
05
0.5
Full range
RS = 50 Ω
MIN
05
0.5
25°C
VIC = 0
0,
TLC2202BC
TYP
650
25°C
Input offset current
IIB
TLC2202AC
MIN
Full range
Input offset voltage long-term
drift (see Note 4)
IIO
TA†
V/ V
V/mV
100
25
115
80
115
dB
80
110
80
110
dB
80
1.8
2.7
Full range
1.8
2.7
2.7
2.7
mA
† Full range is 0°C to 70°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
operating characteristics at specified free-air temperature, VDD± = ±5 V
PARAMETER
TLC2202AC
TEST CONDITIONS
TA†
MIN
TYP
3V
VO = ± 2
2.3
V,,
RL = 10 kΩ, CL = 100 pF
25°C
18
1.8
27
2.7
Full range
1.3
TLC2202BC
MAX
MIN
TYP
18
1.8
27
2.7
MAX
UNIT
SR
Sl
Slew
rate at unity
i gain
i
Vn
Equivalent
q
input
p noise voltage
g
(see Note 5)
f = 10 Hz
25°C
18
35
18
30
f = 1 kHz
25°C
8
15
8
12
VN(PP)
Peak-to-peak
p
equivalent
q
input
p
noise voltage
f = 0.1 to 1 Hz
25°C
0.5
0.5
f = 0.1 to 10 Hz
25°C
0.7
0.7
In
Equivalent input noise current
25°C
0.6
0.6
fA/√Hz
25
C
25°C
19
1.9
19
1.9
MH
MHz
G i bandwidth
Gain
b d idth product
d t
Gain-bandwidth
kHz,R RL = 10 kΩ,
f = 10 kHz,
CL = 100 pF
V/
V/µs
1.3
nV/√Hz
µV
φm
Phase margin at unity gain
RL = 10 kΩ
kΩ, CL = 100 pF
25°C
48°
48°
† Full range is 0°C to 70°C.
NOTE 5: This parameter is tested on a sample basis for the TLC2202A and on all devices for the TLC2202B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
PARAMETER
VIO
αVIO
TEST CONDITIONS
Temperature coefficient of input offset voltage
RS = 50 Ω
VIC = 0
0,
Input offset current
TYP
MAX
100
1000
Full range
1150
Full range
0.001
0.005
Full range
RS = 50 Ω
VIC = 0,
0
Input bias current
VICR
C
Common-mode
d input
i p voltage
l g range
g
RS = 50 Ω
VOH
Maximum high-level output voltage
RL = 10 kΩ
VOL
Maximum low-level output voltage
IO = 0
L
Large-signal
i
l diff
differential
i l voltage
l
amplification
lifi i
100
F ll range
Full
g
0
to
2.7
25°C
4.7
Full range
4.7
V
4.8
0
Full range
CMRR
Common-mode rejection ratio
VO = 0,
RS = 50 Ω
VIC = VICRmin,
kSVR
Supply-voltage rejection ratio (∆VDD ± /∆VIO)
VDD= 4.6
4 6 V to 16 V
IDD
Supply current
VO = 0
0,
No load
µV/mo
pA
p
A
1
25°C
VO = 1 V to 4 V,
RL = 10 kΩ
µV
100
25°C
Full range
VO =1
1 V to 4 V,
RL = 500 kΩ
UNIT
µV/°C
0.5
25°C
IIB
AVD
TLC2202C
MIN
25°C
Input offset voltage
Input offset voltage long-term drift (see Note 4)
IIO
TA†
V
50
50
25°C
150
Full range
100
25°C
25
Full range
15
25°C
75
Full range
75
25°C
80
Full range
80
mV
315
V/ V
V/mV
55
110
dB
110
25°C
1.7
Full range
dB
2.6
2.6
mA
† Full range is 0°C to 70°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using Arrhenius equation and assuming an activation energy of 0.96 eV.
operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
TEST CONDITIONS
VO = 0.5 V to 2.5 V,
RL = 10 kΩ,
CL = 100 pF
SR
Slew rate at unity gain
Vn
Equivalent input noise voltage
VN(PP)
Peak-to-peak equivalent input noise voltage
In
Equivalent input noise current
Gain-bandwidth product
φm
Phase margin at unity gain
† Full range is 0°C to 70°C.
TA†
TLC2202C
MIN
TYP
25°C
1.6
2.5
Full range
1.1
MAX
UNIT
V/µs
f = 10 Hz
25°C
18
f = 1 kHz
25°C
8
f = 0.1 to 1 Hz
25°C
0.5
f = 0.1 to 10 Hz
25°C
0.7
25°C
0.6
fA/√Hz
25°C
19
1.9
MHz
25°C
47°
f = 10 kHz,
CL = 100 pF
RL = 10 kΩ,
RL = 10 kΩ,
CL = 100 pF
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
nV/√Hz
µV
7
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature
p
coefficient
of input offset voltage
TEST CONDITIONS
TLC2202AC
MIN
25°C
VIC = 0,
0
RS = 50 Ω
MAX
80
500
Full range
IIB
Input bias current
VICR
Common-mode input
voltage range
RS = 50 Ω
VOH
Maximum high-level
g
output voltage
RL = 10 kΩ
VOL
Maximum low-level
output voltage
IO = 0
AVD
Large-signal
L
g ig l diff
differential
i l
voltage amplification
RS = 50 Ω
0.001 0.005
Common-mode rejection ratio
VIC = VICRmin,,
VO = 0,
RS = 50 Ω
kSVR
Supply-voltage
pp y
g rejection
j
ratio
(∆VDD ± /∆VIO)
VDD = 4
4.6
6 V to 16 V
IDD
Supply current
VO = 2
2.5
5V
V,
No load
500
25°C
0.5
100
1
1
100
F ll range
Full
g
0
to
2
2.7
25°C
4.7
Full range
4.7
100
0
to
2
2.7
4.8
4.7
50
4.8
25°C
150
100
25°C
25
Full range
15
25°C
75
Full range
75
25°C
80
Full range
80
25°C
315
0
50
50
150
25
pA
pA
mV
315
100
55
µV/mo
V
50
Full range
µV
V
4.7
0
UNIT
µV/°C
100
25°C
CMRR
80
0.001 0.005
0.5
Full range
Full range
VO = 1 V to 4 V,,
RL = 10 kΩ
MAX
05
0.5
Full range
VO = 1 V to 4 V,,
RL = 500 kΩ
TYP
650
05
0.5
25°C
VIC = 0
0,
MIN
650
25°C
Input offset current
TLC2202BC
TYP
Full range
Input offset voltage
long-term drift (see Note 4)
IIO
TA†
V/ V
V/mV
55
15
110
75
110
dB
75
110
80
110
dB
80
1.7
2.6
Full range
1.7
2.6
2.6
2.6
mA
† Full range is 0°C to 70°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
TLC2202AC
TEST CONDITIONS
TA†
MIN
TYP
0 5 V to 2.5
2 5 V,
V,
VO = 0.5
RL = 10 kΩ, CL = 100 pF
25°C
16
1.6
25
2.5
Full range
1.1
TLC2202BC
MAX
MIN
TYP
16
1.6
25
2.5
MAX
UNIT
SR
Sl
Slew
rate at unity
i gain
i
Vn
Equivalent
input
q
p noise voltage
g
(see Note 5)
f = 10 Hz
25°C
18
35
18
30
f = 1 kHz
25°C
8
15
8
12
VN(PP)
Peak-to-peak
p
equivalent
q
input
p
noise voltage
f = 0.1 to 1 Hz
25°C
0.5
0.5
f = 0.1 to 10 Hz
25°C
0.7
0.7
In
Equivalent input noise current
25°C
0.6
0.6
fA/√Hz
25
C
25°C
19
1.9
19
1.9
MH
MHz
G i bandwidth
Gain
b d idth product
d t
Gain-bandwidth
kHz,R RL = 10 kΩ,
f = 10 kHz,
CL = 100 pF
V/
V/µs
1.1
nV/√Hz
µV
φm
Phase margin at unity gain
RL = 10 kΩ
kΩ, CL = 100 pF
25°C
47°
47°
† Full range is 0°C to 70°C.
NOTE 5: This parameter is tested on a sample basis for the TLC2202A and on all devices for the TLC2202B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, VDD ± = ±5 V (unless otherwise noted)
PARAMETER
VIO
αVIO
TEST CONDITIONS
Temperature coefficient of input offset voltage
IIO
Input offset current
IIB
Input bias current
VICR
Common-mode
C
d input
i p voltage
l g range
g
VOM +
Maximum positive peak output voltage swing
RS = 50 Ω
VIC = 0
0,
MIN
TYP
MAX
100
1000
Full range
1200
Full range
0.001
Full range
RS = 50 Ω
VIC = 0,
0
Maximum negative peak output voltage swing
VO = ± 4 V
V,
RL = 500 kΩ
VO = ± 4 V
V,
RL = 10 kΩ
VIC = VICRmin,
L
Large-signal
i
l diff
differential
i l voltage
l
amplification
lifi i
CMRR
Common-mode rejection ratio
VO = 0,
RS = 50 Ω
kSVR
Supply-voltage rejection ratio (∆VDD ± /∆VIO)
VDD = ± 2.3
2 3 V to ± 8 V
IDD
Supply current
VO = 0
0,
No load
µV
0.005
µV/mo
150
25°C
pA
p
A
1
Full range
RS = 50 Ω
UNIT
µV/°C
0.5
25°C
RL = 10 kΩ
AVD
TLC2202I
25°C
Input offset voltage
Input offset voltage long-term drift (see Note 4)
VOM –
TA†
150
Full
F ll range
g
–5
to
2.7
25°C
4.7
Full range
4.7
25°C
– 4.7
Full range
– 4.7
25°C
300
Full range
150
25°C
50
Full range
25
25°C
80
Full range
80
25°C
80
Full range
80
25°C
V
4.8
V
– 4.9
V
560
V/ V
V/mV
100
115
dB
110
1.8
Full range
dB
2.7
2.7
mA
† Full range is – 40°C to 85°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
operating characteristics at specified free-air temperature, VDD± = ±5 V
PARAMETER
TEST CONDITIONS
VO = ± 2.3 V,
CL = 100 pF
SR
Slew rate at unity gain
Vn
Equivalent input noise voltage
VN(PP)
Peak-to-peak equivalent input noise voltage
In
Equivalent input noise current
Gain-bandwidth product
φm
Phase margin at unity gain
† Full range is – 40°C to 85°C.
RL = 10 kΩ,
TA†
TLC2202I
MIN
TYP
25°C
1.8
2.7
Full range
1.2
MAX
UNIT
V/µs
f = 10 Hz
25°C
18
f = 1 kHz
25°C
8
f = 0.1 to 1 Hz
25°C
0.5
f = 0.1 to 10 Hz
25°C
0.7
25°C
0.6
fA/√Hz
25°C
19
1.9
MHz
25°C
48°
f = 10 kHz,
CL = 100 pF
RL = 10 kΩ,
RL = 10 kΩ,
CL = 100 pF
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
nV/√Hz
µV
9
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, VDD ± = ±5 V (unless otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature
p
coefficient
of input offset voltage
TEST CONDITIONS
25°C
VIC = 0,
0
RS = 50 Ω
Input bias current
VICR
Common-mode input
voltage range
VOM +
Maximum p
positive p
peak
output voltage swing
VOM –
Maximum negative
g
p
peak
output voltage swing
AVD
Large-signal
L
g ig l diff
differential
i l
voltage amplification
Full range
MAX
80
500
RS = 50 Ω
RL = 10 kΩ
VO = ± 4 V,,
RL = 500 kΩ
VO = ± 4 V,,
RL = 10 kΩ
MAX
80
500
700
0.001 0.005
0.5
150
25°C
150
1
1
150
F ll range
Full
g
–5
to
2
2.7
25°C
4.7
Full range
4.7
25°C
– 4.7
Full range
– 4.7
25°C
300
Full range
150
25°C
50
Full range
25
25°C
80
Common-mode rejection ratio
VIC = VICRmin,,
VO = 0,
RS = 50 Ω
Full range
80
kSVR
Supply-voltage
pp y
g rejection
j
ratio
(∆VDD ± /∆VIO)
VDD ± ± 2
2.3
3 V to ± 8 V
25°C
80
Full range
80
IDD
Supply current
VO = 0
0,
25°C
150
–5
to
2
2.7
4.8
4.7
– 4.7
4.8
300
– 4.9
50
pA
pA
V
560
150
100
µV/mo
V
– 4.7
560
µV
V
4.7
– 4.9
UNIT
µV/°C
0.001 0.005
0.5
Full range
CMRR
No load
TYP
05
0.5
Full range
RS = 50 Ω
MIN
05
0.5
25°C
VIC = 0
0,
TLC2202BI
TYP
700
25°C
Input offset current
IIB
TLC2202AI
MIN
Full range
Input offset voltage long-term
drift (see Note 4)
IIO
TA†
V/ V
V/mV
100
25
115
80
115
dB
80
110
80
110
dB
80
1.8
2.7
Full range
1.8
2.7
2.7
2.7
mA
† Full range is – 40°C to 85°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
operating characteristics at specified free-air temperature, VDD± = ±5 V
PARAMETER
TLC2202AI
TEST CONDITIONS
TA†
MIN
TYP
3V
kΩ,
VO = ± 2
2.3
V,, RL = 10 kΩ,
CL = 100 pF
25°C
18
1.8
27
2.7
Full range
1.2
TLC2202BI
MAX
MIN
TYP
18
1.8
27
2.7
MAX
UNIT
SR
Sl
Slew
rate at unity
i gain
i
Vn
Equivalent
input
q
p noise voltage
g
(see Note 5)
f = 10 Hz
25°C
18
35
18
30
f = 1 kHz
25°C
8
15
8
12
VN(PP)
Peak-to-peak
p
equivalent
q
input noise voltage
f = 0.1 to 1 Hz
25°C
0.5
0.5
f = 0.1 to 10 Hz
25°C
0.7
0.7
In
Equivalent input noise current
25°C
0.6
0.6
fA/√Hz
25
C
25°C
19
1.9
19
1.9
MH
MHz
G i bandwidth
Gain
b d idth product
d t
Gain-bandwidth
kHz,R RL = 10 kΩ,
f = 10 kHz,
CL = 100 pF
V/
V/µs
1.2
nV/√Hz
µV
φm
Phase margin at unity gain
RL = 10 kΩ
kΩ, CL = 100 pF
25°C
48°
48°
† Full range is – 40°C to 85°C.
NOTE 5: This parameter is tested on a sample basis for the TLC2202A and on all devices for the TLC2202B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
PARAMETER
VIO
αVIO
TEST CONDITIONS
Temperature coefficient of input offset voltage
RS = 50 Ω
VIC = 0
0,
Input offset current
TYP
MAX
100
1000
Full range
1200
Full range
0.001
Full range
RS = 50 Ω
VIC = 0,
0
Input bias current
VICR
C
Common-mode
d input
i p voltage
l g range
g
RS = 50 Ω
VOH
Maximum high-level output voltage
RL = 10 kΩ
VOL
Maximum low-level output voltage
IO = 0
L
Large-signal
i
l diff
differential
i l voltage
l
amplification
lifi i
Common-mode rejection ratio
VO = 0,
RS = 50 Ω
VIC = VICRmin,
kSVR
Supply-voltage rejection ratio (∆VDD ± /∆VIO)
VDD= 4.6
4 6 V to 16 V
IDD
Supply current
VO = 2
2.5
5V
V,
No load
µV/mo
pA
p
A
150
F ll range
Full
g
0
to
2.7
25°C
4.7
Full range
4.7
V
4.8
0
Full range
CMRR
0.005
1
25°C
VO = 1 V to 4 V,
RL = 10 kΩ
µV
150
25°C
Full range
VO =1
1 V to 4 V,
RL = 500 kΩ
UNIT
µV/°C
0.5
25°C
IIB
AVD
TLC2202I
MIN
25°C
Input offset voltage
Input offset voltage long-term drift (see Note 4)
IIO
TA†
V
50
50
25°C
150
Full range
100
25°C
25
Full range
15
25°C
75
Full range
75
25°C
80
Full range
80
25°C
mV
315
V/ V
V/mV
55
110
dB
110
1.7
Full range
dB
2.6
2.6
mA
† Full range is – 40°C to 85°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
SR
Slew rate at unity gain
Vn
Equivalent input noise voltage
VN(PP)
Peak-to-peak equivalent input noise voltage
In
Equivalent input noise current
Gain-bandwidth product
φm
Phase margin at unity gain
† Full range is – 40°C to 85°C.
TEST CONDITIONS
TA†
VO = 0.5 V to 2.5 V,
RL = 10 kΩ,
CL = 100 pF
Full range
25°C
TLC2202I
MIN
TYP
1.6
2.5
1
MAX
UNIT
V/µs
f = 10 Hz
25°C
18
f = 1 kHz
25°C
8
f = 0.1 to 1 Hz
25°C
0.5
f = 0.1 to 10 Hz
25°C
0.7
25°C
0.6
fA/√Hz
25°C
19
1.9
MHz
25°C
47°
f = 10 kHz,
CL = 100 pF
RL = 10 kΩ,
RL = 10 kΩ,
CL = 100 pF
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
nV/√Hz
µV
11
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature
coefficient of
p
input offset voltage
TEST CONDITIONS
25°C
0
VIC = 0,
RS = 50 Ω
IIB
Input bias current
VICR
Common-mode input
voltage range
RS = 50 Ω
VOH
Maximum high-level
g
output
p
voltage
RL = 10 kΩ
VOL
Maximum low-level output
p
voltage
IO = 0
Large-signal
differential
L g ig l diff
i l
voltage amplification
Full range
MAX
80
500
RS = 50 Ω
CMRR
Common-mode rejection ratio
kSVR
Supply-voltage
pp y
g rejection
j
ratio
(∆VDD ± /∆VIO)
VDD = 4
4.6
6 V to 16 V
IDD
Supply current
VO = 2
2.5
5V
V,
No load
80
500
0.5
150
25°C
150
1
1
150
Full
g
F ll range
0
to
2
2.7
25°C
4.7
Full range
4.7
150
0
to
2
2.7
4.8
4.7
50
4.8
150
Full range
100
25°C
25
Full range
15
25°C
75
Full range
75
25°C
80
Full range
80
25°C
315
0
50
50
150
25
pA
pA
mV
315
100
55
µV/mo
V
50
25°C
µV
V
4.7
0
UNIT
µV/°C
0.001 0.005
0.5
Full range
25°C
VIC = VICRmin,,
VO = 0,
RS = 50 Ω
MAX
700
0.001 0.005
Full range
VO =1 V to 4 V,,
RL = 10 kΩ
TYP
05
0.5
Full range
VO = 1 V to 4 V,,
RL = 500 kΩ
MIN
05
0.5
25°C
Input offset current
TLC2202BI
TYP
700
25°C
VIC = 0
0,
AVD
TLC2202AI
MIN
Full range
Input offset voltage long-term
drift (see Note 4)
IIO
TA†
V/ V
V/mV
55
15
110
75
110
dB
75
110
80
110
dB
80
1.7
2.6
Full range
1.7
2.6
2.6
2.6
mA
† Full range is – 40°C to 85°C
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
TLC2202AI
TEST CONDITIONS
TA†
MIN
TYP
0 5 V to 2.5
2 5 V,
V,
VO = 0.5
RL = 10 kΩ, CL = 100 pF
25°C
16
1.6
25
2.5
Full range
TLC2202BI
MAX
MIN
TYP
16
1.6
25
2.5
MAX
UNIT
SR
Sl
Slew
rate at unity
i gain
i
Vn
Equivalent
q
input
p noise voltage
g
(see Note 5)
f = 10 Hz
25°C
18
35
18
30
f = 1 kHz
25°C
8
15
8
12
VN(PP)
Peak-to-peak
p
equivalent
q
input noise voltage
f = 0.1 to 1 Hz
25°C
0.5
0.5
f = 0.1 to 10 Hz
25°C
0.7
0.7
In
Equivalent input noise current
25°C
0.6
0.6
fA/√Hz
25°C
25
C
19
1.9
19
1.9
MHz
MH
G i bandwidth
Gain-bandwidth
Gain
b d idth product
d t
f = 10 kHz,
kHz,R RL = 10 kΩ,
CL = 100 pF
1
V/
V/µs
1
nV/√Hz
µV
φm
Phase margin at unity gain
RL = 10 kΩ
kΩ, CL = 100 pF
25°C
47°
47°
† Full range is – 40°C to 85°C
NOTE 5: This parameter is tested on a sample basis for the TLC2202A and on all devices for the TLC2202B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, VDD ± = ±5 V (unless otherwise noted)
PARAMETER
VIO
αVIO
TEST CONDITIONS
Temperature coefficient of input offset voltage
RS = 50 Ω
VIC = 0
0,
MAX
100
1000
1250
Full range
VICR
C
Common-mode
d input
i p voltage
l g range
g
VOM +
Maximum positive peak output voltage swing
Maximum negative peak output voltage swing
L
Large-signal
i
l diff
differential
i l voltage
l
amplification
lifi i
VO =1
1 V to 4 V,
RL = 500 kΩ
VO = 1 V to 4 V,
RL = 10 kΩ
CMRR
Common-mode rejection ratio
VO = 0,
RS = 50 Ω
VIC = VICRmin,
kSVR
Supply-voltage rejection ratio (∆VDD ± /∆VIO)
VDD= ± 2
2.3
3 V to ± 8 V
IDD
Supply current
VO = 0
0,
No load
µV/mo
pA
p
A
1
500
F ll range
Full
g
–5
to
2.7
25°C
4.7
Full range
RL = 10 kΩ
µV
500
25°C
Full range
RS = 50 Ω
UNIT
µV/°C
0.5
0.001 0.005*
Full range
RS = 50 Ω
VIC = 0,
0
Input bias current
AVD
TYP
Full range
25°C
Input offset current
IIB
VOM –
TLC2202M
MIN
25°C
Input offset voltage
Input offset voltage long-term drift (see Note 4)
IIO
TA†
V
4.8
V
4.7
25°C
– 4.7
Full range
– 4.7
25°C
300
Full range
100
25°C
50
Full range
25
25°C
80
Full range
80
25°C
80
Full range
80
– 4.9
V
560
V/ V
V/mV
100
115
dB
110
25°C
1.8
Full range
dB
2.7
2.7
mA
* On products compliant to MIL-STD-883, Class B, this parameter is not production tested.
† Full range is – 55°C to 125°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using Arrhenius equation and assuming an activation energy of 0.96 eV.
operating characteristics at specified free-air temperature, VDD± = ±5 V
PARAMETER
TEST CONDITIONS
VO = ± 2.3 V,
CL = 100 pF
SR
Slew rate at unity gain
Vn
Equivalent input noise voltage
VN(PP)
Peak-to-peak equivalent input noise voltage
In
Equivalent input noise current
Gain-bandwidth product
φm
Phase margin at unity gain
† Full range is – 55°C to 125°C.
RL = 10 kΩ,
TA†
TLC2202M
MIN
TYP
25°C
1.8
2.7
Full range
1.1
MAX
UNIT
V/µs
f = 10 Hz
25°C
18
f = 1 kHz
25°C
8
f = 0.1 to 1 Hz
25°C
0.5
f = 0.1 to 10 Hz
25°C
0.7
25°C
0.6
fA/√Hz
25°C
19
1.9
MHz
25°C
48°
f = 10 kHz,
CL = 100 pF
RL = 10 kΩ,
RL = 10 kΩ,
CL = 100 pF
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
nV/√Hz
µV
13
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, VDD ± = ±5 V (unless otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature
coefficient
p
of input offset voltage
TA†
TEST CONDITIONS
RS = 50 Ω
VICR
Common-mode input
voltage range
Maximum p
positive p
peak
VOM +
output voltage swing
VOM –
AVD
Maximum negative
g
p
peak
output voltage swing
Large-signal
differential
L g ig l diff
i l
voltage amplification
Common-mode rejection
j
CMRR
ratio
kSVR
Supply-voltage
pp y
g rejection
j
ratio (∆VDD ± /∆VIO)
500
Full range
RS = 50 Ω
RL = 10 kΩ
VO = ± 4 V,,
RL = 500 kΩ
VO = ± 4 V,,
RL = 10 kΩ
MAX
80
500
0.001 0.005*
0.5
Full range
0.5
500
25°C
500
1
1
500
Full
g
F ll range
–5
to
2.7
25°C
4.7
Full range
4.7
25°C
– 4.7
Full range
– 4.7
25°C
300
Full range
100
25°C
50
Full range
25
VO = 0,, VIC = VICRmin,,
RS = 50 Ω
25°C
80
Full range
80
VDD ± = ± 2.3
2 3 V to ± 8 V
25°C
80
Full range
80
500
–5
to
2.7
4.8
4.7
– 4.7
4.8
– 4.9
– 4.7
560
300
50
µV/mo
pA
pA
V
V
560
100
100
µV
V
4.7
– 4.9
UNIT
µV/°C
05
0.5
0.001 0.005*
Full range
RS = 50 Ω
TYP
750
05
0.5
25°C
VIC = 0
0,
Input bias current
80
MIN
750
25°C
Input offset current
IIB
MAX
25°C
0
VIC = 0,
TLC2202BM
TYP
Full range
Input offset voltage
long-term drift (see Note 4)
IIO
TLC2202AM
MIN
100
V/ V
V/mV
25
115
80
115
80
110
80
80
110
dB
dB
25°C
1.8
2.7
1.8
2.7
mA
Full range
2.7
2.7
* On products compliant to MIL-STD-883, Class B, this parameter is not production tested.
† Full range is – 55°C to 125°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
IDD
14
Supply current
VO = 0
0,
No load
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
operating characteristics at specified free-air temperature, VDD± = ±5 V
PARAMETER
SR
Sl
Slew
rate at unity
i gain
i
TLC2202AM
TEST CONDITIONS
TA†
MIN
TYP
VO = ± 2
2.3
3V
V,
RL = 10 kΩ
kΩ,
CL = 100 pF
25°C
18
1.8
27
2.7
Full range
1.1
TLC2202BM
MAX
MIN
TYP
18
1.8
27
2.7
MAX
UNIT
V/
V/µs
1.1
Vn
Equivalent input noise voltage
(see Note 5)
f = 10 Hz
25°C
18
35*
18
30*
f = 1 kHz
25°C
8
15*
8
12*
VN(PP)
Peak to peak equivalent input
Peak-to-peak
noise voltage
f = 0.1 to 1 Hz
25°C
0.5
0.5
f = 0.1 to 10 Hz
25°C
0.7
0.7
In
Equivalent input noise current
25°C
0.6
0.6
fA/√Hz
25°C
19
1.9
19
1.9
MHz
MH
25°C
48°
48°
G i b d id h product
Gain-bandwidth
p d
φm
Phase margin at unity gain
f = 10 kHz,
RL = 10 kΩ,,
CL = 100 pF
RL = 10 kΩ,,
CL = 100 pF
nV/√Hz
µV
* On products compliant to MIL-STD-883, Class B, this parameter is not production tested.
† Full range is – 55°C to 125°C.
NOTE 5: This parameter is tested on a sample basis for the TLC2202A and on all devices for the TLC2202B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
15
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperatures, VDD = 5 V (unless otherwise noted)
PARAMETER
VIO
αVIO
TEST CONDITIONS
Temperature coefficient of input offset voltage
RS = 50 Ω
VIC = 0
0,
Input offset current
TYP
MAX
100
1000
Full range
1250
Full range
0.001 0.005*
Full range
RS = 50 Ω
VIC = 0,
0
Input bias current
VICR
C
Common-mode
d input
i p voltage
l g range
g
RS = 50 Ω
VOH
Maximum high-level output voltage
RL = 10 kΩ
VOL
Maximum low-level output voltage
IO = 0
L
Large-signal
i
l diff
differential
i l voltage
l
amplification
lifi i
500
F ll range
Full
g
0
to
2.7
25°C
4.7
Full range
4.7
V
4.8
0
Full range
CMRR
Common-mode rejection ratio
VIC = VICRmin
min, RS = 50 Ω
kSVR
Supply-voltage rejection ratio (∆VDD ± /∆VIO)
VDD = 4.6
4 6 V to 16 V
IDD
Supply current
VO = 2
2.5
5V
V,
No load
µV/mo
pA
p
A
1
25°C
VO = 1 V to 4 V,
RL = 10 kΩ
µV
500
25°C
Full range
VO = 1 V to 4 V,
RL = 500 kΩ
UNIT
µV/°C
0.5
25°C
IIB
AVD
TLC2202M
MIN
25°C
Input offset voltage
Input offset voltage long-term drift (see Note 4)
IIO
TA†
V
50
50
25°C
150
Full range
75
25°C
25
Full range
10
25°C
75
Full range
75
25°C
80
Full range
80
25°C
mV
315
V/ V
V/mV
55
110
dB
110
1.7
Full range
dB
2.6
2.6
mA
* On products compliant to MIL-STD-883, Class B, this parameter is not production tested.
† Full range is – 55°C to 125°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
TEST CONDITIONS
VO = 0.5 V to 2.5 V,
RL = 10 kΩ,
CL = 100 pF
SR
Slew rate at unity gain
Vn
Equivalent input noise voltage
VN(PP)
Peak-to-peak equivalent input noise voltage
In
Equivalent input noise current
Gain-bandwidth product
φm
Phase margin at unity gain
† Full range is – 55°C to 125°C.
16
TA†
TLC2202M
MIN
TYP
25°C
1.6
2.5
Full range
0.9
f = 10 Hz
25°C
18
f = 1 kHz
25°C
8
f = 0.1 to 1 Hz
25°C
0.5
f = 0.1 to 10 Hz
25°C
0.7
MAX
UNIT
V/µs
nV/√Hz
µV
25°C
0.6
fA/√Hz
f = 10 kHz,
CL = 100 pF
RL = 10 kΩ,
25°C
19
1.9
MHz
RL = 10 kΩ,
CL = 100 pF
25°C
47°
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature coefficient of
input offset voltage
RS = 50 Ω
VIC = 0
0,
80
500
Full range
RS = 50 Ω
Input bias current
VICR
Common mode input
Common-mode
voltage range
RS = 50 Ω
VOH
high-level
Maximum high
level output
voltage
RL = 10 kΩ
VOL
Maximum low
low-level
level output
voltage
IO = 0
Full range
Common mode rejection
Common-mode
ratio
VO = 0, VIC = VICRmin,
RS = 50 Ω
kSVR
Supply-voltage
Supply
voltage rejection
ratio (∆VDD ± /∆VIO)
6 V to 16 V
VDD = 4
4.6
IDD
Supply current
VO = 2
2.5
5V
V,
No load
80
500
25°C
0.5
500
1
1
500
F ll range
Full
g
0
to
2.7
25°C
4.7
Full range
4.7
500
0
to
2.7
4.8
4.7
50
4.8
0
50
25°C
150
Full range
75
25°C
25
Full range
10
25°C
75
Full range
75
25°C
80
Full range
80
25°C
Full range
315
50
25
pA
pA
mV
315
75
55
µV/mo
V
50
150
µV
V
4.7
0
UNIT
µV/°C
0.001 0.005*
500
25°C
CMRR
MAX
05
0.5
0.5
Full range
VO = 1 V to 4 V,
RL = 10 kΩ
TYP
750
0.001 0.005*
Full range
VO = 1 V to 4 V,
RL = 500 kΩ
MIN
05
0.5
25°C
IIB
L
Large-signal
i
l diff
i l
Large
signal
differential
voltage amplification
MAX
750
25°C
Input offset current
TLC2202BM
TYP
Full range
VIC = 0
0,
AVD
TLC2202AM
MIN
25°C
Input offset voltage
long-term drift (see Note 4)
IIO
TA†
TEST CONDITIONS
V/ V
V/mV
55
10
110
75
110
dB
75
110
80
110
dB
80
1.7
2.6
2.6
1.7
2.6
2.6
mA
* On products compliant to MIL-STD-883, Class B, this parameter is not production tested.
† Full range is – 55°C to 125°C
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
SR
Sl
Slew
rate at unity
i gain
i
TLC2202AM
TEST CONDITIONS
TA†
MIN
TYP
VO = 0.5
0 5 V to 2
2.5
5V
V,
kΩ
RL = 10 kΩ,
CL = 100 pF
25°C
16
1.6
25
2.5
Full range
0.9
TLC2202BM
MAX
MIN
TYP
16
1.6
25
2.5
MAX
V/
V/µs
1.1
Vn
Equivalent input noise voltage
(see Note 5)
f = 10 Hz
25°C
18
35*
18
30*
f = 1 kHz
25°C
8
15*
8
12*
VN(PP)
Peak to peak equivalent input
Peak-to-peak
noise voltage
f = 0.1 to 1 Hz
25°C
0.5
0.5
f = 0.1 to 10 Hz
25°C
0.7
0.7
In
Equivalent input noise current
φm
UNIT
nV/√Hz
µV
25°C
0.6
0.6
fA/√Hz
G i b d id h product
Gain-bandwidth
p d
f = 10 kHz,
RL = 10 kΩ,,
CL = 100 pF
25°C
19
1.9
19
1.9
MHz
MH
Phase margin at unity gain
RL = 10 kΩ,,
CL = 100 pF
25°C
47°
47°
* On products compliant to MIL-STD-883, Class B, this parameter is not production tested.
† Full range is – 55°C to 125°C
NOTE 5: This parameter is tested on a sample basis for the TLC2202A and on all devices for the TLC2202B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
18
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
electrical characteristics, VDD = 5 V, TA = 25°C (unless otherwise noted)
PARAMETER
VIO
TEST CONDITIONS
Input offset voltage
Input offset voltage long-term drift (see Note 4)
IIO
IIB
TLC2202Y
MIN
Input offset current
RS = 50 Ω
VIC = 0
0,
Input bias current
VICR
C
Common-mode
d input
i p voltage
l g range
g
RS = 50 Ω
0
to
2.7
VOH
VOL
Maximum high-level output voltage
RL = 10 kΩ
4.7
Maximum low-level output voltage
AVD
Large-signal differential voltage amplification
IO = 0
VO = 1 V to 4 V,
CMRR
Common-mode rejection ratio
VO = 1 V to 4 V,
VO = 0, VICRmin,
TYP
MAX
UNIT
100
1000
µV
0.001
0.005
µV/mo
0.5
pA
1
pA
V
4.8
0
RL = 500 Ω
150
315
RL = 10 Ω
25
55
RS = 50 Ω
75
110
V
50
mV
V/mV
dB
kSVR
Supply-voltage rejection ratio (∆VDCC /∆VIO)
VDD = 4.6 to 16 V
80
110
dB
IDD
Supply current
VO = 2.5 V,
No load
1.7
2.6
mA
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
operating characteristics at VDD = 5 V, TA = 25°C
PARAMETER
TEST CONDITIONS
VO = 0.5 V to 2.5 V,
CL = 100 pF
SR
Positive slew rate at unity gain
Vn
Equivalent input noise voltage
VN(PP)
Peak-to-peak equivalent input noise voltage
In
Equivalent input noise current
RL = 10 kΩ,
TLC2202Y
MIN
TYP
1.6
2.5
f = 10 Hz
18
f = 10 kHz
8
f = 0.1 to 1 Hz
0.5
f = 0.1 to 10 Hz
0.7
B1
Gain-bandwidth product
f = 10 kHz,
CL = 100 pF
φm
Phase margin at unity gain
RL = 10 kΩ,
POST OFFICE BOX 655303
MAX
UNIT
V/µs
nV/√Hz
µV
0.6
pA/√Hz
RL = 10 kΩ,
1.9
MHz
CL = 100 pF
47°
• DALLAS, TEXAS 75265
19
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
PARAMETER MEASUREMENT INFORMATION
10 kΩ
VDD +
2 kΩ
VI
VDD +
–
+
VO
VDD –
VO
CL
(see Note A)
VDD – /GND
20 Ω
20 Ω
–
+
100 Ω
RL
NOTE A: CL includes fixture capacitance.
Figure 1. Noise-Voltage Test Circuit
Figure 2. Phase-Margin Test Circuit
VDD +
VI
–
+
VO
Ground Shield
VDD –
CL
(see Note A)
VDD +
–
+
RL
VO
VDD – /GND
pA
pA
NOTE A: CL includes fixture capacitance.
Figure 3. Slew-Rate Test Circuit
Figure 4. Input-Bias and OffsetCurrent Test Circuit
typical values
Typical values presented in this data sheet represent the median (50% point) of device parametric performance.
input bias and offset current
At the picoamp bias current level of the TLC2202, TLC2202A, and TLC2202B, accurate measurement of the
bias current becomes difficult. Not only does this measurement require a picoammeter, but test socket leakages
can easily exceed the actual device bias currents. To measure these small currents, Texas Instruments uses
a two-step process. The socket leakage is measured using picoammeters with bias voltages applied but with
no device in the socket. The device is then inserted in the socket, and a second test measuring both the socket
leakage and the device input bias current is performed. The two measurements are then subtracted
algebraically to determine the bias current of the device.
noise
Texas Instruments offers automated production noise testing to meet individual application requirements. Noise
voltage at f = 10 Hz and f = 1 kHz is 100% tested on every TLC2201B device, while lot sample testing is
performed on the TLC2202A. For other noise requirements, please contact the factory.
20
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
VIO
Input offset voltage
Distribution
5
IIB
Input bias current
vs Common
Common-mode
mode input voltage
vs Free-air temperature
6
7
VOM
Maximum peak output voltage
vs Output current
vs Free-air temperature
VO(PP)
Maximum peak-to-peak output voltage
vs Frequency
11
VOH
High l
High-level
l output
p voltage
l g
vs Frequency
vs Current
vs Free-air temperature
12
13
14
VOL
Low-level output voltage
vs Output current
vs Free-air temperature
15
16
AVD
Large-signal differential voltage amplification
vs Frequency
vs Free-air temperature
17
18
IOS
Short-circuit output current
vs Supply voltage
vs Free-air temperature
19
20
CMRR
Common-mode rejection ratio
vs Frequency
IDD
Supply current
vs Supply voltage
vs Free-air temperature
Pulse response
Small signal
Large signal
Slew rate
vs Supply voltage
vs Free-air temperature
29
30
Noise voltage (referred to input)
0.1 to 1 Hz
0.1 to 10 Hz
31
32
Gain-bandwidth product
vs Supply voltage
vs Free-air temperature
33
34
Phase margin
vs Supply voltage
vs Free-air temperature
35
36
Phase shift
vs Frequency
17
SR
φm
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
8,9
10
21, 22
23
24
25, 26
27, 28
21
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS†
TLC2202
DISTRIBUTION OF
INPUT OFFSET VOLTAGE
INPUT BIAS CURRENT
vs
COMMON-MODE INPUT VOLTAGE
16
12
VDD ± = ± 5 V
TA = 25°C
8
6
IIIB
IB – Input Bias Current – pA
Percentage of Units – %
14
10
1726 Amplifiers Tested From 1 Wafer Lot
VDD ± = ± 15 V
TA = 25°C
P Package
10
8
6
4
4
2
0
–2
–4
–6
2
–8
0
–1000
– 600
– 200
200
600
1000
– 10
–5
VIO – Input Offset Voltage – µV
–4
–3
–2
Figure 5
150
100
50
0
45
65
85
105
125
VVOM
OM+ – Maximum Positive Peak Output Voltage – V
I IB – Input Bias Current – pA
200
25
1
2
3
4
5
VDD ± = ± 5 V
TA = 25°C
4
3
2
1
0
0
TA – Free-Air Temperature – °C
1
2
3
|IO| – Output Current – mA
Figure 7
Figure 8
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
22
5
MAXIMUM POSITIVE PEAK
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
VDD ± = ± 5 V
VO = 0
VIC = 0
250
0
Figure 6
INPUT BIAS CURRENT
vs
FREE-AIR TEMPERATURE
300
–1
VIC – Common-Mode Input Voltage – V
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
4
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS†
MAXIMUM PEAK OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
6
–5
VDD ± = ± 5 V
TA = 25°C
VOM – Maximum Peak Output Voltage – V
VOM
VOM – Maximum Negative Peak Output Voltage – V
MAXIMUM NEGATIVE PEAK
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
– 4.5
–4
– 3.5
–3
0
2
4
6
8
4
2
VDD ± = ± 5 V
RL = 10 kΩ
0
–2
–4
–6
– 75
10
– 50
|IO| – Output Current – mA
– 25
0
25
50
75 100
TA – Free-Air Temperature – °C
Figure 9
Figure 10
MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE
vs
FREQUENCY
HIGH-LEVEL OUTPUT VOLTAGE
vs
FREQUENCY
10
5
VOH – High-Level Output Voltage – V
V0H
VO(PP) – Maximum Peak-to-Peak Output Voltage – V
125
8
TA = – 55°C
6
TA = 125°C
4
2
VDD ± = ± 5 V
RL = 10 kΩ
0
10 k
30 k
100 k
300 k
1M
4
TA = – 55°C
3
TA = 125°C
2
1
VDD = 5 V
RL = 10 kΩ
0
10 k
30 k
100 k
f – Frequency – Hz
f – Frequency – Hz
Figure 11
Figure 12
300 k
1M
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
23
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS†
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
HIGH-LEVEL OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
VDD
6
VDD = 5 V
RL = 10 kΩ
VDD – 2
V OH – High-Level Output Voltage – V
VOM
V OH – High-Level Output Voltage – V
VOM
TA = 25°C
VDD = 5 V
VDD – 4
VDD – 6
VDD = 10 V
VDD – 8
VDD – 10
VDD – 12
VDD = 16 V
VDD – 14
VDD – 16
0
1
2
3
4
5
4
3
2
1
0
– 75
5
– 50
IOH – High-Level Output Current – mA
– 25
0
25
50
75 100
TA – Free-Air Temperature – °C
Figure 13
Figure 14
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
LOW-LEVEL OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
1.5
2
VDD = 5 V
VDD = 10 V
VDD = 5 V
VOL
VOL – Low-Level Output Voltage – V
TA = 25°C
VOL
VOL – Low-Level Output Voltage – V
125
VDD = 16 V
1.5
1
0.5
IOL = 5 mA
1
0.5
IOL = 1 mA
0
0
2
4
6
8
IOL – Low-Level Output Current – mA
10
0
– 75
– 50
Figure 15
– 25
0
25
50
75 100
TA – Free-Air Temperature – °C
Figure 16
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
24
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
125
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS†
LARGE-SIGNAL DIFFERENTIAL VOLTAGE
AMPLIFICATION AND PHASE SHIFT
vs
FREQUENCY
30°
120
VDD ± = ± 5 V
RL = 10 kΩ
CL = 100 pF
TA = 25°C
50°
80
70°
60
90°
Phase Shift
ÁÁ
ÁÁ
ÁÁ
40
110°
20
130°
150°
0
– 20
10
100
1k
10 k
100 k
AVD
A
VD – Large-Signal Differential
Voltage Amplification – dB
AVD
130
Phase Shift
100
AVD
AVD – Large-Signal Differential
Voltage Amplification – dB
LARGE-SIGNAL DIFFERENTIAL VOLTAGE
AMPLIFICATION
vs
FREE-AIR TEMPERATURE
ÁÁ
ÁÁ
ÁÁ
170°
1M
VDD ± = ± 5 V, RL = 500 kΩ
120
110
VDD = 5 V, RL = 500 kΩ
VDD ± = ± 5 V, RL = 10 kΩ
100
90
80
– 75
VDD = 5 V, RL = 10 kΩ
– 50
f – Frequency – Hz
Figure 17
SHORT-CIRCUIT OUTPUT CURRENT
vs
FREE-AIR TEMPERATURE
15
VO = 0
TA= 25°C
IIOS
OS – Short-Circuit Output Current – mA
IIOS
OS – Short-Circuit Output Current – mA
12
4
VID = – 100 mV
0
–4
–8
VID = 100 mV
– 12
0
1
2
125
Figure 18
SHORT-CIRCUIT OUTPUT CURRENT
vs
SUPPLY VOLTAGE
8
– 25
0
25
50
75 100
TA – Free-Air Temperature – °C
3
4
5
6
|VDD ±| – Supply Voltage – V
7
8
VDD ± = ± 5 V
VO = 0
10
5
VID = – 100 mV
0
–5
VID = 100 mV
– 10
– 15
– 75
– 50
Figure 19
– 25
0
25
50
75 100
TA – Free-Air Temperature – °C
125
Figure 20
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
25
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS†
COMMON-MODE REJECTION RATIO
vs
FREQUENCY
COMMON-MODE REJECTION RATIO
vs
FREQUENCY
120
VDD ± = ± 5 V
TA = 25°C
CMRR – Common-Mode Rejection Ratio – dB
CMRR – Common-Mode Rejection Ratio – dB
120
100
80
60
40
20
0
VDD = 5 V
TA = 25°C
100
80
60
40
20
0
10
100
1K
10K
100K
10
1M
100
f – Frequency – Hz
Figure 21
10K
100K
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
2.5
2.5
VO = 0
No Load
VO = VDD + /2
No Load
2
IIDD
DD – Supply Current – mA
2
1.5
TA = 125°C
TA = 25°C
TA = – 55°C
1
0.5
VDD ± = ± 5 V
VDD = 5 V
1.5
1
0.5
0
0
1
2
3
4
5
6
7
8
0
– 75
– 50
|VDD ±| – Supply Voltage – V
Figure 23
– 25
0
25
50
75 100
TA – Free-Air Temperature – °C
Figure 24
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
26
1M
Figure 22
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
IIDD
DD – Supply Current – mA
1K
f – Frequency – Hz
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
125
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS
VOLTAGE-FOLLOWER
SMALL-SIGNAL
PULSE RESPONSE
VO – Output Voltage – mV
VO
75
50
160
VDD ± = ± 5 V
RL = 10 kΩ
CL = 100 pF
TA = 25°C
VDD = 5 V
RL = 10 kΩ
CL = 100 pF
TA = 25°C
140
120
VO – Output Voltage – mV
VO
100
VOLTAGE-FOLLOWER
SMALL-SIGNAL
PULSE RESPONSE
25
0
– 25
– 50
–75
100
80
60
40
20
0
–100
0
1
2
3
4
5
6
– 20
7
4
1
2
3
t – Time – µs
0
t – Time – µs
Figure 25
5
VDD = 5 V
RL = 10 kΩ
CL = 100 pF
TA = 25°C
4
4
VO – Output Voltage – V
VO
3
VO – Output Voltage – V
VO
7
VOLTAGE-FOLLOWER
LARGE-SIGNAL
PULSE RESPONSE
5
2
1
0
–1
–2
VDD ± = ± 5 V
RL = 10 kΩ
CL = 100 pF
TA = 25°C
–4
6
Figure 26
VOLTAGE-FOLLOWER
LARGE-SIGNAL
PULSE RESPONSE
–3
5
3
2
1
0
–1
–5
0
5
10
15
20
25
30
35
0
40
t – Time – µs
5
10
15
20
25
30
35
40
t – Time – µs
Figure 27
Figure 28
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
27
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS†
SLEW RATE
vs
SUPPLY VOLTAGE
SLEW RATE
vs
FREE-AIR TEMPERATURE
4
4
SR –
RL = 10 kΩ
CL = 100 pF
TA = 25°C
SR –
3
SR – Slew Rate – V/µ s
SR – Slew Rate – V/µ s
3
SR +
2
SR +
2
1
1
0
– 75
0
0
1
2
3
4
6
5
7
8
VDD ± = ± 5 V
RL = 10 kΩ
CL = 100 pF
– 50
|VDD ±| – Supply Voltage – V
– 25
0
25
50
75 100
TA – Free-Air Temperature – °C
Figure 29
Figure 30
NOISE VOLTAGE
(REFERRED TO INPUT)
OVER A 10-SECOND INTERVAL
NOISE VOLTAGE
(REFERRED TO INPUT)
OVER A 10-SECOND INTERVAL
1
1
VDD ± = ± 5 V
f = 0.1 to 1Hz
TA= 25°C
0.75
125
VDD ± = ± 5 V
f = 0.1 to 10 Hz
TA= 25°C
0.8
0.6
0.5
V
Noise Voltage – µ
uV
V
Noise Voltage – µ
uV
0.4
0.25
0
– 0.25
0.2
0
– 0.2
– 0.4
– 0.5
– 0.6
– 0.75
–1
0
– 0.8
1
2
3
4
5
6
7
8
9
10
–1
0
1
t – Time – s
2
3
4
5
6
7
8
9
t – Time – s
Figure 31
Figure 32
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
28
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
10
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS†
GAIN-BANDWIDTH PRODUCT
vs
SUPPLY VOLTAGE
GAIN-BANDWIDTH PRODUCT
vs
FREE-AIR TEMPERATURE
2.5
f = 10 kHz
RL = 10 kΩ
CL = 100 pF
TA = 25°C
Gain-Bandwidth Product – MHz
Gain-Bandwidth Product – MHz
2.1
2
1.9
1.8
0
1
2
3
4
5
6
|VDD ±| – Supply Voltage – V
7
f = 10 kHz
RL = 10 kΩ
CL = 100 pF
VDD ± = ± 5 V
2
VDD = 5 V
1.5
1
– 75
8
– 50
– 25
0
25
50
75 100
TA – Free-Air Temperature – °C
Figure 33
Figure 34
PHASE MARGIN
vs
SUPPLY VOLTAGE
50°
PHASE MARGIN
vs
FREE-AIR TEMPERATURE
50°
RL = 10 kΩ
CL = 100 pF
TA = 25°C
VDD ± = ± 5 V
48°
φom
m – Phase Margin
48°
φom
m – Phase Margin
125
46°
44°
42°
VDD = 5 V
46°
44°
42°
RL = 10 kΩ
CL = 100 pF
40°
0
1
2
3
4
5
6
|VDD ±| – Supply Voltage – V
7
8
40°
– 75
– 50
– 25
0
25
50
75
100
125
TA – Free-Air Temperature – °C
Figure 35
Figure 36
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
29
TLC2202, TLC2202A, TLC2202B, TLC2202Y
Advanced LinCMOS LOW-NOISE PRECISION
DUAL OPERATIONAL AMPLIFIERS
SLOS056A – MAY 1990 – REVISED AUGUST 1994
APPLICATION INFORMATION
latch-up avoidance
Because CMOS devices are susceptible to latch-up due to their inherent parasitic thyristors, the TLC2202,
TLC2202A, and TLC2202B inputs and outputs are designed to withstand – 100-mA surge currents without
sustaining latch-up; however, techniques reducing the chance of latch-up should be used whenever possible.
Internal protection diodes should not be forward biased in normal operation. Applied input and output voltages
should not exceed the supply voltage by more than 300 mV. Care should be exercised when using capacitive
coupling on pulse generators. Supply transients should be shunted by the use of decoupling capacitors
(0.1 µF typical) located across the supply rails as close to the device as possible.
electrostatic discharge protection
These devices use internal ESD-protection circuits that prevent functional failures at voltages at or below
2000 V. Care should be exercised in handling these devices as exposure to ESD may result in degradation of
the device parametric performance.
30
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments (TI) reserves the right to make changes to its products or to discontinue any semiconductor
product or service without notice, and advises its customers to obtain the latest version of relevant information
to verify, before placing orders, that the information being relied on is current.
TI warrants performance of its semiconductor products and related software to the specifications applicable at
the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are
utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each
device is not necessarily performed, except those mandated by government requirements.
Certain applications using semiconductor products may involve potential risks of death, personal injury, or
severe property or environmental damage (“Critical Applications”).
TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED, OR WARRANTED
TO BE SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS.
Inclusion of TI products in such applications is understood to be fully at the risk of the customer. Use of TI
products in such applications requires the written approval of an appropriate TI officer. Questions concerning
potential risk applications should be directed to TI through a local SC sales office.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards should be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance, customer product design, software performance, or
infringement of patents or services described herein. Nor does TI warrant or represent that any license, either
express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property
right of TI covering or relating to any combination, machine, or process in which such semiconductor products
or services might be or are used.
Copyright  1995, Texas Instruments Incorporated