Type:
Series
CCT
27
30
35
40
Single
Linear
LED
L1R2U
M100 Recessed
Linear LED Flush End
(Flanged Extrusion
/Flangeless Endcaps)
Scale = 1 : 4
2
4" (100mm)
3
5
4
1. Housing - Continuous, 6063-T6 extruded
aluminum profile up to 12 feet long. Joined
with Connector Plus Joining System for
ease of installation and to ensure a uniform
appearance. For use in insulated ceilings,
designed for direct contact with thermal insulation.
2. Driver - Electronic Class 2 driver, universal for 120V/277V. Standard driver dimmable with trailing edge dimmers, high efficiency, PFC>0.95, soft start. Lutron A -Series
(DM3/DME), 0-10V Linear (DM) and 0-10V
Logarithmic (DML) or DALI (DMD) dimming
may be specified as well.
3. LED Light Engine - High efficacy LED
light engine equipped with brand-name
LEDs, available in 2700K, 3000K, 3500K or
Selux Corp. © 2013
TEL (845) 834-1400
FAX (845) 834-1401
www.selux.us
L1RxU-0713-01 (ss-v3.1)
1 ft.
2 ft. T-Bar
3 ft.
4 ft. T-Bar
5 ft.
6 ft. T-Bar
7 ft.
8 ft. T-Bar
Finish
WH
BK
SV
SP
White
Black
Silver
Specify
Premium
Color
Voltage
120
277
RUN Create Run
Runs can be pre-configured using various combinations in 1/4” steps,
starting at 8ft.
Consult factory for less than 2 ft. fixture length. 2 3 ft. min. when using with DM, DML, DMD, or EMN. 3Not available in combination with EMN.
4" (100mm)
413/16"(122mm)
Nominal
Length
Nominal
Length
_
Mounting Diagrams
Suspension Clips (SH)
6
Pre-installed Rod (TS)
7
4000K. CCT tolerance within a 3-step
MacAdam ellipse.
4. Flange - 9/16" (15mm) wide flange
runs full lengths of both sides and is part
of the main extruded body. Specify continuous flange (L1R1U) or flush end
(L1R2U). Flush end not to be used with
T-Bar ceiling.
5. Shielding - LED Optimized white
acrylic diffuser lens.
6. Spring Steel Suspension Clips Supplied two places, located nominally
every 4 ft. Support wires supplied and
installed by others.
7. Pre-installed 1" 1/4-20 Studs Attached to fixture, see p.3 for location
details.
8. Coupling and Threaded Rod to
Structure - Supplied and installed by others.
9. Rotating Crossbar - For inaccessible
ceilings, adjustable for ceiling thicknesses
from 1/4" to 2". Supplied, (2-3) per fixture.
10. Steel Wall Bracket & 1/4-20 Rod Supplied, (2-3) per fixture, see p.3 for
Union Made Affiliated
with IBEW Local 363
NRTL Listed for Damp
Location (i.e. UL, CSA)
8
83/8"(211mm)
location details. (Fasteners to wall and
wall anchors by others.)
11. Aluminum Wallbracket - Secured to
wall (fasteners and wall anchors by others) and runs entire length of fixture. Also
supplied for width of fixtures when supplied with continuous flange. Allows for
1/8" gap between flange and wall to create
shadow line allowing for unevenness of
wall. See p.3 for location details.
12. Flex Whip -(not shown) Standard and
dimming wiring. See p.4 for details.
13. Stand-by Battery Pack - (not shown)
Mounted on top of and accessible through
fixture housing. See p.4 for details.
Linear Runs - Continuous run configurations are available in 1/4” steps, starting at
8ft. Round up length to nearest nominal
foot to generate order code. Suspension
points might not be symmetrical for certain
run length. Please consult factory if symmetrical suspension locations are
required.
Interior Luminaire Finish - Selux utilizes
a high quality Polyester Powder Coating.
All Selux luminaires are finished in our
Tiger Drylac certified facility and undergo a
For IC and Non-IC
Construction
DM1
DML1
Voltage
Options
Dimming (0-10V) Linear
Dimming (0-10V)
Logarithmic
DME1 Lutron Eco-System
Dimming
DM31 Lutron 3-Wire Dimming
DMD1 Digital Addressable
(DALI) Dimming
CCEA3 Chicago Plenum
EMN1 Battery Pack
TB
T-Bar Length
(used for RUN only)
DL
Damp Location
Perimeter Mount (PM)
Rotating Crossbars (RC)
9
Finish
_
Scale = 1 : 8
11
10
41/2"
1
(factory installed)
RC2 Rotating
Crossbars
PM Perimeter
Mount
01
2T
03
4T
05
6T
07
8T
Mounting
_
(114mm)
L1R1U / L1R2U
1
LW LED
SH Suspension
optimized
Clips
white lens TS 1” Studs
Shielding
_
4"
(L1R2U
not to be used
with T-Bar ceiling)
2700K
3000K
3500K
4000K
Mounting
Shielding
LW
(100mm)
1L35
Options
_
CCT
4"
L1R1U
M100 Recessed
Linear LED Flanged
Extrusion
Light
Engine
Light
Engine
(100mm)
Series
_ 1L35 _
Qty:
4"
Project:
(100mm)
M100 LED
Recessed Linear LED
Flanged Extrusion
five stage intensive pretreatment process
where product is thoroughly cleaned,
phosphated, and sealed. Selux powder
coated products provide excellent salt and
humidity resistance as well as ultra violet
resistance for color retention. All products
are tested in accordance with test specifications for coatings from ASTM and PCI.
Standard interior colors are White (WH),
Black (BK), and Silver (SV). Selux premium colors (SP) are available, please specify from your Selux color selection guide.
5 Year Limited LED Luminaire Warranty
- Selux offers a 5 Year Limited Warranty to
the original purchaser that the M100
series LED luminaire shall be free from
defects in material and workmanship for
up to five (5) years from date of shipment.
This limited warranty covers the fixture,
LED driver and LED light engine when
installed and operated according to Selux
instructions. Fixture suitable for ambient
temperature of 35° C (95° F). For details
and exclusions, see “Selux Terms and
Condition of Sale.”
Listings and Ratings: Tested to
IESNA LM-79-08
and LM-80 test
standards at 25° C
ambient temperature.
For DoE Lighting
Facts labels, see p.2
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter
the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
M100 LED
Photometry
Recessed Linear LED
Flanged Extrusion
COEFFICIENTS OF UTILIZATION - Zonal cavity method
L1R1U / 350mA LED / 3500K CCT
Catalog #: L1R1U-1L35-35-LW-4T-120
Report #: LTL-23873-1
Lamp: 180 white LEDs
Total Lumens: 2705
Luminaire Efficacy: 82 lm/W
Max Candela: 948 @ 0.5o from Vertical
Spacing Criterion (0-180): 1.26
Spacing Criterion (90-270): 1.26
Spacing Criterion (Diagonal): 1.38
237
474
0
5
15
25
35
45
55
65
75
85
90
711
948
0°
90°
Vertical Plane is parallel with the lamp.
Vertical Plane is perpendicular to the lamp.
DOWNLOAD IES FILE:
CANDELA DISTRIBUTION
0
22.5
45
67.5
945
945
945 945
939
943
934 940
903
909
902 907
837
841
837 840
740
745
742 745
522
526
625 525
486
489
488 489
336
339
340 340
187
188
187 186
51
53
53
54
.08
.24
.40
.80
90
945
945
908
841
744
623
487
336
187
50
.16
ZONAL LUMEN SUMMARY
ZONE
0-30
0-40
0-60
0-90
90-180
0-180
LUMENS %LAMP
731.61
1196.47
2113.4
2704.62
.01
2704.63
N.A.
N.A.
N.A.
N.A.
N.A.
N.A.
%FIXT.
27.10
44.20
78.10
100.0
0
100.0
http://www.selux.us/fileadmin/us/interior/ies_file/L10_IES.zip
Fixture Length
Energy Consumption for Non-Dimming Luminaires
Standard Driver
1ft
2ft
3ft
4ft
5ft
6ft
7ft
8ft
RUN
(approximate)
8.4W 15.9W 24.3W 33.0W 40.1W 50.8W 63.4W 69.7W 8.75 W/ft.
DM3/DME Drivers at 277V 17.7W 26.6W 38.0W 44.3W 56.9W 70.8W 77.2W 10.1W/ft.
DM/DMD Driver
Selux Corp. © 2013
L1RxU-0713-02 (ss-v3.1)
17.3W 25.9W 37.1W 43.2W 55.6W 69.2W 75.4W
9.9W/ft.
LED CCT Prorate Table
(Values based on 4ft. 1L35 Light Engine.)
CCT
3000K
3500K
4000K
Lumens
2507
2705
2639
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the
function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
M100 LED
Recessed Linear LED
Flanged Extrusion
Layout Dimensions
L1R1U and T-Bar Ceilings (TS, SH)
L1R1U and L1R2U Suspensions (TS, RC, PM, SH)
Nominal (4 foot shown) - Side view
Nominal (4 foot shown) - Side view
Outside Flange
Fixture Housing
Suspensions
Feed
Fixture Length (including endcaps)
2' typical
Nominal (4 foot shown) - Bottom view
413/16
(122mm)
C
L to CL of T-Bar
1L35 Single Linear LED
1’ individual
2’ individual
3’ individual
4’ individual
5’ individual
6’ individual
7’ individual
8’ individual
Outside Flange
L1R1U/L1R2U
Fixture Housing
12 11/16" (323mm) 11 13/16" (301mm)
L1R1U
C
L to CL of T-Bar
34"
11
(865mm) 32 /8" (836mm)
7
1 5/8” (41mm)
N/A
6 /8” (155mm)
47 /8" (1215mm) 46 /16" (1187mm) 48" (1219mm)
7
11
55 /16" (1403mm) 54 /8" (1375mm) N/A
3
1
71 /8" (1825mm) 70 /16" (1797mm) 72" (1829mm)
7
11
87 /8" (2225mm) 86 /2" (2196mm)
5
1
N/A
95 /8" (2435mm) 94 /16" (2406mm) 96" (2438mm)
7
11
L10U
Suspensions
N/A
23 /8" (606mm) 22 /16" (577mm) 24" (607mm)
7
Suspensions
Feed into 7/8" hole
Nominal (4 foot shown) - Bottom view
L1R1U
Equal
1 /8” (41mm)
5
1
6 /8” (155mm)
1
6 /8” (155mm)
1
6 /8” (155mm)
1
6 /8” (155mm)
1
6 /8” (155mm)
Suspension clips (SH) located nominally every 4ft. Location can be adjusted in field.
1
L1R1U
Feed
3” (76mm)
4” (102mm)
2” (51mm)
2” (51mm)
2” (51mm)
2” (51mm)
2” (51mm)
2” (51mm)
For other lengths, lamping, continuous runs or configurations please specify overall length (in feet), accessories desired and sketch/drawing of
configuration. Selux will detail project drawings upon order and supply submittal drawings for approval. Individual fixtures cannot be field joined.
If you have any questions please contact Selux customer service or applications engineering for assistance (1-800-SELUX-CS).
Selux Corp. © 2013
L1RxU-0713-03 (ss-v3.1)
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the
function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
M100 LED
Recessed Linear LED
Flanged Extrusion
EMN Option / Flex Whips
M100 LED EMN Option
Stand-by Battery Packs mounted to top of fixture and can be maintained through fixture from below the ceiling.
For RUNS, please specify location of lit section (approx. 2ft.).
For Individual fixtures, the lit section will be located on the feed end of the luminaire.
23/4" (70mm)
Input
EMN-model #
ILB-2412
EMN Battery Pack
2.5W
Operation
Duration
90min
Fixture Lumen
Output
800 lm
M100 LED Flex Whip
For wiring diagram, see below.
3/8" Flexible Metal Conduit, 6' long
6" leads
Straight Conduit
Fitting on free end
90° Elbow Conduit Fitting
into 7/8" hole
Wiring
STANDARD
Standard
Wiring
FEED
DRIVER(s)
(xx WATTS-LED)
GREEN
WHITE
BLACK
DME
Lutron 3-Wire
Dimming
FEED
DRIVER(s)
(xx WATTS-LED)
GREEN
WHITE
BLACK
VIOLET
VIOLET/WHITE
Lutron
Eco-System
Dimming
Standard
Wiring
DM3
DME
DM, DML &
DMD
DM3
DM/DML/DMD
FEED
GREEN
WHITE
BLACK
ORANGE
FEED
GREEN
WHITE
BLACK
GREY (-)
PURPLE (+)
DRIVER(s)
(xx WATTS-LED)
DRIVER(s)
(xx WATTS-LED)
Dimming and
Digital Addressable
(DALI) Dimming
GREEN = Ground (Green) / WHITE = Neutral (White)
BLACK = Hot (Black)
*Where Applicable, these wire(s) are added to the STD. Above.
ORANGE = 3-Wire Dimming Control
VIOLET = ‘E1’ Digital Link Dimming Control
VIOLET / WHITE = ‘E2’ Digital Link Dimming Control
GREY = ‘E1’ Digital or 0-10V Dimming Control
PURPLE = (+) DALI or 0-10V Dimming Control
Selux Corp. © 2013
L1RxU-0713-04 (ss-v3.1)
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the
function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
M100 LED
Recessed Linear LED
Flanged Extrusion
Compatible Dimmers
Standard Drivers:
Compatible with reverse phase control, also known as “trailing edge” dimmers. Minimum dimming level down to 10%. Inrush current per driver is
4A/20µs. Please consult factory for details and compatibility.
Reverse phase control or “trailing edge.”
With reverse phase control, the dimmer starts to provide power immediatedly after the zero cross. Dimming is achieved by delaying the time
at which the dimmer stops conducting.
DM3/DME Drivers:
Equipped with Lutron Hi-lume A-Series. Please visit Lutron’s website at www.lutron.com for further information regarding dimmer and controller
compatibility. Minimum dimming level down to 1%.
DM Drivers:
Equipped with 0-10V dimming drivers for linear dimming curve. Minimum dimming level preset to 0.1%. Driver manufacturer recommends the
following dimmers, switches or dimming control systems.
Dimmer & Switches
Manufacturer
Lutron Electronics
Control Systems
Manufacturer
Lutron Electronics
Website
Type
Nova T - NTFTV
www.lutron.com/LEDtool Diva - DVTV
Diva - NFTV
GraphicEye - GRX-TVI w GRX3503
www.lutron.com/LEDtool Energy Savr Node - QSN-4T16S
TVM2 Module
DML Drivers:
Recommended Driver
Dimming Curve
Linear
Linear
Equipped with 0-10V dimming drivers for logarithmic dimming curve. Minimum dimming level preset to 0.1%. Driver manufacturer recommends
the following dimmers, switches or dimming control systems.
Dimmer & Switch
Manufacturer
Website
Type
Busch-Jaeger
www.busch-jaeger.de
2112U-101
Leviton Lighting Controls
www.leviton.com
IllumaTech - IP710-DLX
Jung
Lightolier Controls
Merten
Pass & Seymour
The Watt Stopper
Selux Corp. © 2013
L1RxU-0713-05 (ss-v3.1)
www.gb.jung.de
www.lightolier.com
www.merten.de
www.legrand.us
www.wattstopper.com
240-10
ZP600FAM120
5729
Recommended Driver
Dimming Curve
Logarithmic
CD4FB-W
DCLV1
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the
function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.