LUCENSURFACE
TM
2X2, 2X4, and 1X4 Architectural Recessed
T5, T8 and Biax
Project Name
Date
Catalog Number
Type
CONSTRUCTION Prepainted formed 22 gauge cold rolled steel housing. Highly reflective die-formed white painted
reflector. Wiring access available on both sides and top of housing.
OPTICS Single piece extruded acrylic lens with convex wings and articulated center spine creating a fully luminous
housing with optimal glare control. High reflective white reflectors maintain uniform lens brightness.
ELECTRICAL T5, T5HO: Program start 120/277 volt integral electronic ballast with less than 10% THD. T8: Instant
start 120/277V electronic ballast with less than 10% THD. Standard single circuit. Each ballast provided with disconnects to meet luminaire disconnect code requirement.
MOUNTING LucenTM is designed to install into acoustical grid and inaccessible ceilings. Specify G1, G9 or GS for
acoustical grid ceiling. Specify FL for inaccessible ceilings. Consult factory for detailed installation instructions.
FINISH Prepainted white polyester polymer finish on exposed trim. Optional Paint After Fabrication available if speci-
FLUORESCENT CROSSfied.
SECTIONS
LABELS UL and cUL Listed, approved for dry/damp location. Pre-painted fixtures are to be used in dry locations only.
Patent No: D671,258
For damp location, must specify Paint After Fabrication (PAF) in the Options section of the Luminaire Specification.
MADE
IN USA
Efficiency
LFL
Convertible
LED
Shielding Options
LFL
Convertible
LED
Satine Lens (A)
Lucen 1x4 Surface Mount
Lucen 2x2, 2x4 Surface Mount
TM
TM
PowerDensity
4-3/4”
4-3/4”
LED
Convertible
13-1/2"
25-1/2"
LFL
Side View
LED
4-3/4”
Convertible
LFL
White Trim (W)
25-1/2” (2x2)
49-1/2" (2x4 and 1x4)
Silver Trim (S)
L U M I N A I R E S P E C I F I C AT I O N
LU__HOUSING
LU22A- LucenT M 2x2
Recessed, Satine Lens
LU22W- LucenT M 2x2
Recessed, Satine Lens
with white trim
LU22S- LucenT M 2x2
Recessed, Satine Lens
with silver trim
LU24A- LucenT M 2x4
Recessed, Satine Lens
LU24W- LucenT M 2x4
Recessed, Satine Lens
with white trim
LU24S- LucenT M 2x4
Recessed, Satine Lens
with silver trim
LU14A- LucenT M 1x4
Recessed, Satine Lens
LU14W- LucenT M 1x4
Recessed, Satine Lens
with white trim
LU14S- LucenT M 1x4
Recessed, Satine Lens
with silver trim
Sample Catalog #: LU22A-2T5HO-S-120-1C-W
LED_T___CROSS SECTIONSSMOUNTING
LAMPS
1
2x2 only
1BX40- (1) 40W Biax
2BX40- (2) 40W Biax
1BX55- (1) 55W Biax
2BX55- (2) 55W Biax
2x2, 2x4, 1x4
1T52T53T51T5HO
2T5HO3T5HO1T82T83T8-
(1) T5
(2) T5
(3) T57
(1) T5HO
(2) T5HO
(3) T5HO7
(1) T8
(2) T8
(3) T87
___-
__-
__-
___
VOLTAGE
CIRCUITING
FINISH
OPTIONS
TM
Single Circuit
S- Surface
StepMount
Switching5
Mount
Surface
LucenTM 1x4SWLucen
2x2, 2x4 Surface1CMount
2C- Dual Circuit3,5
GLR- Internal Fast-Blow Fuse
1D- Single Circuit Dimming5
AM- Antimicrobial Paint
3,5
4-3/4”
2D- Dual Circuit Dimming
4-3/4”
DSM- Daylight Sensor
Master 4,5
1B- Single Circuit with Battery Pack
Sensor included5,6
2B- Dual Circuit with Battery Pack3,4,5
DSS- Daylight Sensor Satellite
13-1/2"
25-1/2" 1E- Single Circuit with Emergency Circuit4,5
- Sensor not included5,6
Side View
4-3/4”
120277347UNV-
120 V
277 V
347 V1,2
UNV2
(120/277)
W- Matte
White (2x2)
25-1/2”
49-1/2" (2x4 and 1x4)
Consult factory for 347 volt ballast. 2Not available for use with a battery pack. 3Dual circuit available for 2 (side-by-side) and 3 (inboard/outboard) lamp configurations. 4Emergency circuit or battery pack to
be on center lamp with 3 lamp configurations. 5Some LucenT M configurations will not accommodate all options. Consult factory. 6See back page for ordering information. Requires 0-10 volt dimming. 73 lamp
T5, T5HO and T8 are not available on 1x4 luminaire.
1
®
Pinnacle Architectural Lighting 12655 East 42nd Avenue, Suite 50 Denver, CO 80239
Phone 303.322.5570
Fax 303.322.5568 www.pinnacle-ltg.com
© 2014 Pinnacle Architectural Lighting®
April 2014
Specifications and dimensions subject to change without notice. Specification sheets that appear on pinnacle-ltg.com are the most recent version and supersede all other previously printed or electronic versions.
PHOTOMETRICS
LUCEN SUFACE
981
1468976
753933
1445
723
1413
736
491
1101725
734 484
565700
1084
376467
723
542
1060
491
706
245
367 242
188233
361
181
353
Test # 204530
Part # LU22A-2T5HO
Total Luminaire Efficiency: 80%
# 204560
TestTest
# 204535
# LU22W-2T5HO
PartPart
# LU24A-2T5
Luminaire
Efficiency:
TotalTotal
Luminaire
Efficiency:
83%77%
# 204590
TestTest
204523
Test
##204565
# LU22S-2T5HO
PartPart
LU14A-1T5
Part
##LU24W-2T5
Total
Luminaire
Efficiency:
75%
Total
Luminaire
Efficiency:
81%
Total
Luminaire
Efficiency:
82%
F E AT U R E S A N D O P T I O N S
INTEGRAL DAYLIGHT SENSOR
1468
1101
734
367
Test # 204535
Part # LU24A-2T5
LAMP MAINTENANCE
Total Luminaire Efficiency: 83%
APPLICATION: Daylight sensor is a turn key solution for lighting control. Integral sensor is wired to the 0-10
volt dimming ballast at the factory. No additional wiring is required by the contractor.
1445
1413
DAYLIGHT SENSOR: Daylight sensor dims lights based on electric light and presence of daylight. Sensor can
1084
1060
control up to
20 dimming ballasts. Sensor is factory calibrated to 45 footcandles
(fc), adjustable by 1/3 to 3 times
753 723
723 706
the default
setting by rotating the aperture.
565 361INFORMATION: Specify “DSM” or “DSS” in the Options
542 353section of the part number when orderORDERING
376 Daylight Sensor. Daylight Sensor Master (DSM) includes491
ing Integral
the fixture with sensor and dimming ballast.
Controls188
DSS units. Daylight Sensor Satellite (DSS) includes the fixture
181 with a sensor compatible dimming ballast
only. Must be used in conjunction with a DSM unit. (0-10v) dimming must be utilized.
(Sample Catalog #: LU22A-1T5-S-120-1D-W-DSM)
Test # 204565
Test # 204595
Part # LU24W-2T5
Part # LU24S-2T5
BALLAST MAINTENANCE
Luminaire Efficiency: 82%
Luminaire Efficiency: 79%
TestTotal
# 204523
TestTotal
# 204553
Part # LU14A-1T5
Part # LU14W-1T5
Total Luminaire Efficiency: 81%
Total Luminaire Efficiency: 78%
Plunger
Pull off
ballast cover
Lamps
Door Frame
OPENING THE 753
LENS: Push lens up to locate plungers. Plungers are above 723
the lens on the inside
565 of the fixture. Depress both plunger heads with fingers 542
and simultaneously
pull door frame down.
376
491
188
#8-32 Screw
705
REMOVING BALLAST SCREWS:
Remove screw holding the ballast
529
cover to fixture.
353
181
Test # 204523
Part # LU14A-1T5
Lamps
Total Luminaire Efficiency: 81%
176
Test # 204553
Part # LU14W-1T5
Ballast
Total Luminaire Efficiency: 78%
ACCESSING THE LAMPS: Lamps are
accessible once lens is open. Door frame
remains captive to fixture housing during
lamp maintenance.
®
Plunger
Test # 204583
# LU14S-1T5
BallastPart
Cover
Total Luminaire Efficienc: 74%
REMOVING BALLAST TRAY: Ballast
cover easily comes off. Ballast is now
accessible from room side of fixture.
Pinnacle Architectural Lighting 12655 East 42nd Avenue, Suite 50 Denver, CO 80239
Phone 303.322.5570
Fax 303.322.5568 www.pinnacle-ltg.com
© 2014 Pinnacle Architectural Lighting®
April 2014
Specifications and dimensions subject to change without notice. Specification sheets that appear on pinnacle-ltg.com are the most recent version and supersede all other previously printed or electronic versions.
Door Frame
#8-32 Screw
Pull driver
705
529
353
176