1.877.817.6028
www.DiodeLED.com
®
MATTONE™ DIRECT-WIRE LED STEP LIGHT FIXTURE
WARNING
INSTALLATION GUIDE
Read all warnings and installation instructions thoroughly.
Safety & Warnings
• Install in accordance with the National Electric Code, and local
regulations.
• The MATTONE Support Housing must be grounded. Ensure to attach
earth ground to the MATTONE Support Housing.
• This product is intended to be installed and serviced by a qualified,
licensed electrician.
• Do not install this product in an environment outside the listed ambient
temperature.
• This product is IP65 rated for outdoor applications when installed with
MATTONE Support Housing (housing box sold separately).
• Do not modify or disassemble this product beyond instructions or the
warranty will be void.
• Ensure applicable wire is installed between driver, fixture, and any
controls in between. When choosing wire, factor in voltage drop,
amperage rating, and type (in-wall rated, wet location rated, etc.).
Inadequate wire installation could overheat wires, and cause a fire.
120V
AC
Dry/Wet Location
Quick Specs
Input Voltage
100-277VAC, 50/60Hz
Environment
Outdoor / wet location / IP65
Power Consumption
3W / .025A
Mounting
Mounts in the MATTONE Support Housing
(sold separately). Support Housing can be
installed with the MATTONE Mounting
Brackets (also sold separately).
Ambient Temperature
-4° ~ 122°F (-20° ~ 50°C)
Certifications
cULus Listed (USA & Canada) Surface
Mount Luminaire, UL # E336778.
For full specifications, see the ‘Specification Sheet’ available at the online
product page.
Installation
Install in accordance with the NEC and local regulations.
WARNING
Shock Hazard. May result in serious injury or death.
1.Turn off 120-277VAC power at circuit breaker.
2.Mount MATTONE Support Housing (DI-MATB-HOUS) to studs with
MATTONE Mounting Brackets (DI-MATB-HANG).
3.Pull main power cable through MATTONE Support Housing and attach
earth Ground to housing chassis.
4.Attach AC Hot to MATTONE light engine Hot (black). Attach AC Neutral
to light engine Neutral (white).
5.Insert light engine into support housing and attach faceplate with
included Allen screws (use included #3 Allen key).
6.Turn on 120-277VAC power at circuit breaker.
See next page for wiring and mounting diagram.
IG100214-1.2
info@DiodeLED.com
1 OF 2
www.DiodeLED.com
1.877.817.6028
www.DiodeLED.com
®
MATTONE™ DIRECT-WIRE LED STEP LIGHT FIXTURE
INSTALLATION GUIDE
Wiring & Mounting Diagram
13.5“- 25.5” adjustable arms
for wall stud mounting.
Use 2x screws on each side of arm to secure
Mounting Bracket to stud (8x wood screws included).
2x MATTONE Mounting Brackets (DI-MATB-HANG)
(Sold Separately by the pair)
Utilize guide nail to
fasten arm to stud.
MATTONE Support Housing
(DI-MATB-HOUS)
(Sold Separately)
120-277VAC~
50/60Hz
Y/G
Neutral (White)
Hot (Black)
MATTONE Light Engine
STUD
MATTONE Faceplate
When installing
mounting
brackets, note
that elbow of
cleat will
partially bend or
recess based on
firmness of
surface.
STUD
2x Faceplate Allen Screws
(use #3 Allen key)
2x Screw Caps
Additional Resources
Visit the on-line product page at www.DiodeLED.com for additional product specifications & warranty information.
• MATTONE™ DIRECT-WIRE LED STEP LIGHT FIXTURE SPECIFICATION SHEET
For full specifications.
QUESTIONS?
Visit www.DiodeLED.com or contact Customer Support at info@DiodeLED.com
or 1.877.817.6028 Monday through Friday, 7:00am - 5:00pm PST.
IG100214-1.2
info@DiodeLED.com
2 OF 2
www.DiodeLED.com