RIGID INDUSTRIES
®
™
Diagram A
A
E D
F
Rigid Industries® warrants that this product will be free from defects in
material and workmanship. If you believe your Rigid Industries product is
defective, it must be returned to Rigid Industries for inspection by our
warranty claims department. If, after inspection, Rigid Industries verifies that
the defect was not caused by negligence, abuse, unauthorized repair or
disassembly, Rigid Industries will determine whether the product will be
repaired or replaced in accordance with Rigid Industries Limited Lifetime
Warranty*.
Warranty Periods:
PRODUCT INSTRUCTIONS
™
™
C
• Flashlights – 2 year • All LED Light bars – Limited Lifetime
• Accessories and Mounts – 2 years • Batteries – 90 days
D
Warranty Coverage:
To begin your warranty claim, you must have a Return Merchandise
Authorization (RMA) number. To get your RMA number, please contact
our warranty department by phone at 855-760-5337 ext. 1008, or by
filling out the Return Merchandise Authorization Form on our website.
B
Diagram B
A
E
F
B
All of the following will immediately void all warranties:
A - RDS Light Bar
B - Mount Bushing (2)
C - Mount Bracket (2)
D - 1/4” Nylon Locknut (4)
E - 1/4” Flat Washer (4)
F - 1/4” Hex Head Screw (4)
• Customer negligence – The customer has modified the light and/or is not using it
for the recommend application. DO NOT OPEN YOUR LIGHT
• Customer abuse – Damage to the light beyond normal wear and tear.
• Repair work done by unauthorized personnel without Rigid Industries’ approval.
• If the light has been opened or any screws have been removed.
C
All warranties are non-transferable. Warranty terms and policies are subject to
change without notice.
*For all information regarding the Rigid Industries Limited Lifetime Warranty
please call 855-760-5337 ext. 1008, email warranty@RigidIndustries.com, or
visit our warranty page online at RigidIndustries.com/Warranty.
www.RigidIndustries.com
A - RDS Light Bar
B - Mount Bushing (2)
C - Mount Bracket (2)
D - 1/4” Nylon Locknut (4)
E - 1/4” Flat Washer (4)
F - 1/4” Hex Head Screw (4)
™
PKG-IS-002-Rev03
RIGID INDUSTRIES
®
™
Diagram A
A
E D
F
Rigid Industries® warrants that this product will be free from defects in
material and workmanship. If you believe your Rigid Industries product is
defective, it must be returned to Rigid Industries for inspection by our
warranty claims department. If, after inspection, Rigid Industries verifies that
the defect was not caused by negligence, abuse, unauthorized repair or
disassembly, Rigid Industries will determine whether the product will be
repaired or replaced in accordance with Rigid Industries Limited Lifetime
Warranty*.
Warranty Periods:
PRODUCT INSTRUCTIONS
™
Diagram B
A
™
• Flashlights – 2 year • All LED Light bars – Limited Lifetime
• Accessories and Mounts – 2 years • Batteries – 90 days
C
D
Warranty Coverage:
To begin your warranty claim, you must have a Return Merchandise
Authorization (RMA) number. To get your RMA number, please contact
our warranty department by phone at 866-760-LEDS ext. 1008, or by
filling out the Return Merchandise Authorization Form on our website.
B
B
All of the following will immediately void all warranties:
A - RDS Light Bar
B - Mount Bushing (2)
C - Mount Bracket (2)
D - 1/4” Nylon Locknut (4)
E - 1/4” Flat Washer (4)
F - 1/4” Hex Head Screw (4)
C
• Customer negligence – The customer has modified the light and/or is not using it
for the recommend application. DO NOT OPEN YOUR LIGHT
• Customer abuse – Damage to the light beyond normal wear and tear.
• Repair work done by unauthorized personnel without Rigid Industries’ approval.
• If the light has been opened or any screws have been removed.
All warranties are non-transferable. Warranty terms and policies are subject to
change without notice.
*For all information regarding the Rigid Industries Limited Lifetime Warranty
please call 855-760-5337 ext. 1008, email warranty@RigidIndustries.com, or
visit our warranty page online at RigidIndustries.com/Warranty.
PKG-IS-002-Rev03
www.RigidIndustries.com
A - RDS Light Bar
B - Mount Bushing (2)
C - Mount Bracket (2)
D - 1/4” Nylon Locknut (4)
E - 1/4” Flat Washer (4)
F - 1/4” Hex Head Screw (4)
™
E
F
Figure 1
1. Install mounting brackets onto light as shown in Diagram A or
B. Secure hardware to a snug position and mount your light in
desired location.
Battery Eyelets
+ Red to 12V positive
- Black to ground
2. Disconnect the negative battery cable from the battery.
40 amps - All Sizes
Switch Wiring
4. Route wires from light to desired location to connect to wires
from switch. See Figure 1.
For 20” and 30” RDS light bars, connect Deutsch plug
on light to Deutsch plug on wire harness.
Roof Mounts
Coming Soon for
your make and model.
5. When installing Rigid lights on a 24V DC system be
sure to use a 24V relay. When installing multiple lights
be sure to have adequate fusing.
For 40”, 50” and 54” RDS light bars, no plugs are used.
To connect wiring, slide heat shrink tubing over wires
before connecting. Use supplied butt connectors to
connect the wires, then apply heat to the connectors
to shrink around wires. Slide heat shrink tubing into
place, centered over butt connector, then apply heat
to shrink around wires.
6. Finally, test lights to ensure proper function and then
secure mounting hardware according to your desired
light beam angle.
Weld-On Tabs
For technical support call us at 855-760-5337.
Visit RigidIndustries.com for more accessories!
Figure 1
Battery Eyelets
+ Red to 12V positive
- Black to ground
4. Route wires from light to desired location to connect to wires
from switch. See Figure 1.
For 20” and 30” RDS light bars, connect Deutsch plug
on light to Deutsch plug on wire harness.
For technical support call us at 855-760-5337.
* Rigid Industries always recommends installation from an
industry professional. Be sure to read warranty information on back.
40 Amps - All sizes
Roof Mounts
Coming Soon for
your make and model.
Weld-On Tabs
DESIGNE
D
For 40”, 50” and 54” RDS light bars, no plugs are used.
To connect wiring, slide heat shrink tubing over wires
before connecting. Use supplied butt connectors to
connect the wires, then apply heat to the connectors
to shrink around wires. Slide heat shrink tubing into
place, centered over butt connector, then apply heat
to shrink around wires.
GINEERED, AS
, EN
BLED
SEM
*NOTE: Using mounting hardware or wiring other than what is supplied
by Rigid Industries can result in damage and possible void of warranty.
Available
RDS-Series™
Switch Wiring
6. Finally, test lights to ensure proper function and then
secure mounting hardware according to your desired
light beam angle.
Accessories
Minimum Fusing
Requirements
3. Attach red terminal eyelet to battery positive or any
12V DC source. Secure black terminal eyelet to suitable ground
or battery negative. Route harness to desired switch and
mounting locations, secure with zip ties. Beware of sharp
edges, abrasive surfaces and heat sources when wiring.
5. When installing Rigid lights on a 24V DC system be
sure to use a 24V relay. When installing multiple lights
be sure to have adequate fusing.
Security Kit
IN T H U S A
E
* Rigid Industries always recommends installation from an
industry professional. Be sure to read warranty information on back.
2. Disconnect the negative battery cable from the battery.
Bar Clamps
GINEERED, AS
, EN
BLED
SEM
*NOTE: Using mounting hardware or wiring other than what is supplied
by Rigid Industries can result in damage and possible void of warranty.
1. Install mounting brackets onto light as shown in Diagram A or
B. Secure hardware to a snug position and mount your light in
desired location.
Available
RDS-Series™
3. Attach red terminal eyelet to battery positive or any
12V DC source. Secure black terminal eyelet to suitable ground
or battery negative. Route harness to desired switch and
mounting locations, secure with zip ties. Beware of sharp
edges, abrasive surfaces and heat sources when wiring.
Congratulations on your purchase of Rigid™ Lights!
Accessories
Minimum Fusing
Requirements
DESIGNE
D
Congratulations on your purchase of Rigid™ Lights!
Bar Clamps
Security Kit
IN T H U S A
E
Visit RigidIndustries.com for more accessories!