08.00 GENERAL
DISTRIBUTION SURGE ARRESTERS
CUTOUTS AND ARRESTERS GENERAL
08.00-01
08.00-03
08.01 CUTOUTS AND ARRESTERS
ARRESTERS, 10KV
APPLICATION OF DIRECT CONNECTED ARRESTERS ON DISTRIBUTION TRANSFORMERS
CUTOUTS AND BRACKETS
CUTOUTS AND ARRESTERS 2 OR 3 EACH ON TRIPLE MOUNTING BRACKET
CUTOUTS AND ARRESTERS SINGLE-PHASE TERMINATION ON POLE MOUNTED
"L" BRACKET
CUTOUT AND ARRESTER, (2) OR (3)-PHASE TERMINATION ON TRIPLE MOUNTING
BRACKET
SLACKSPAN WITH FUSED CUTOUT
VERTICAL DOUBLE DEADEND WITH CUTOUTS
VERTICAL CONSTRUCTION WITH LIGHTNING ARRESTER
DOUBLE CIRCUIT CONSTRUCTION WITH LIGHTNING ARRESTER
HORIZONTAL CONSTRUCTION TO HORIZONTAL DEADEND
HORIZONTAL CONSTRUCTION TO HORIZONTAL WITH CUTOUT (FLYING TAP)
HORIZONTAL CONSTRUCTION TO BRANCH LINE
HORIZONTAL CONSTRUCTION WITH LIGHTNING ARRESTER
SINGLE-PHASE CONSTRUCTION - FUSED TAP
VERTICAL CONSTRUCTION - TANGENT FUSED TAP CONSTRUCTION
08.04 SECTIONALIZERS
ELECTRONIC RESETTABLE SECTIONALIZERS
08.05 RECLOSERS - SINGLE-PHASE CONFIGURATIONS
RECLOSERS, SECTIONALIZERS, TRANSFERS AND THREE-PHASE RECLOSER
LIGHTNING ARRESTER MOUNTING DETAIL
RECLOSER IDENTIFICATION
TYPICAL SINGLE-PHASE RECLOSER DIMENSIONS, WEIGHTS AND OIL CAPACITIES
COOPER RECLOSERS OPERATING LEVERS
RECLOSER ASSEMBLY, VERTICAL CONSTRUCTION
OIL CIRCUIT RECLOSER - SINGLE-PHASE INSTALLATION BYPASS CUTOUT BRACKET
RECLOSER ASSEMBLY, VERTICAL CONSTRUCTION, FEEDER
RECLOSER ASSEMBLY, VERTICAL CONSTRUCTION, FEEDER
RECLOSER ASSEMBLY, VERTICAL CONSTRUCTION SLACK SPAN TAP
RECLOSER ASSEMBLY, VERTICAL CONSTRUCTION SLACK SPAN TAP
OIL CIRCUIT RECLOSERS, THREE-PHASE INSTALLATION, HORIZONTAL CONSTRUCTION
SINGLE-PHASE UNITS
OIL CIRCUIT RECLOSERS, THREE-PHASE INSTALLATION, HORIZONTAL CONSTRUCTION
SINGLE-PHASE UNITS
08.06 RECLOSERS - THREE-PHASE CONFIGURATIONS
RECLOSER AND FRAME, THREE-PHASE, ABB WITH VERTICAL BYPASS SWITCH
RECLOSER ASSEMBLY, THREE-PHASE, ABB WITH VERTICAL BYPASS SWITCH
ABB RECLOSER ON VERTICAL DOUBLE CIRCUIT WITH VERTICAL BYPASS SWITCH
RECLOSER AND FRAME, THREE-PHASE, VIPER ST, WITH VERTICAL BYPASS SWITCH
RECLOSER AND FRAME, THREE-PHASE, VIPER ST, WITH VERTICAL BYPASS SWITCH
RECLOSER ASSEMBLY, THREE-PHASE, VIPER ST WITH VERTICAL BYPASS SWITCH
RECLOSER AND FRAME, THREE-PHASE, VIPER ST,
WITH VERTICAL BYPASS SWITCH - 25KV CONSTRUCTION
RECLOSER AND FRAME, THREE-PHASE, VIPER ST,
WITH VERTICAL BYPASS SWITCH - 25KV CONSTRUCTION
ASSEMBLY, THREE-PHASE, VIPER ST, WITH VERTICAL BYPASS SWITCH 25KV CONSTRUCTION
DOUBLE CIRCUIT, THREE-PHASE, VIPER ST
DOUBLE CIRCUIT, THREE-PHASE, VIPER ST
VIPER RECLOSER HORIZONTAL CONSTRUCTION
VIPER RECLOSER HORIZONTAL CONSTRUCTION
WIRING DIAGRAM FOR PT CLUSTER FOR G&W VIPER
WIRING DIAGRAM FOR PT CLUSTER ABB 1PT TO 3PT CONVERSION
FUSE AND BATTERY FOR SEL 651-R2 CONTROLS (ABB & VIPER)
FUSE AND BATTERY FOR SEL 651-R2 CONTROLS (ABB & VIPER)
SPECIAL PROVISIONS - G&W VIPER ST, IPP INTERCONNECTION
ABB TO SEL 651-R2 CONTROL CONVERSION ON ABB RECLOSERS
ABB TO SEL 651-R2 CONTROL CONVERSION ON ABB RECLOSERS
RECLOSER ASSEMBLY, THREE-PHASE, VERTICAL, 600 AMP SWITCH
RECLOSER ASSEMBLY, THREE-PHASE, VERTICAL, 600 AMP SWITCH
5
4/18/16
KATIGBAK
BURLISON
ADCOCK
4
12/16/15
KATIGBAK
BURLISON
ADCOCK
3
12/19/14
KATIGBAK
GUINN
ADCOCK
0
11/30/10
CECCONI
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
08.01-01
08.01-04
08.01-10
08.01-11
08.01-12
08.01-13
08.01-14
08.01-16
08.01-28
08.01-29
08.01-32
08.01-33
08.01-36
08.01-37
08.01-38
08.01-39
08.04-02
08.05-00
08.05-01
08.05-02
08.05-06
08.05-15A
08.05-15B
08.05-16A
08.05-16B
08.05-18A
08.05-18B
08.05-114A
08.05-114B
08.06-08A
08.06-08B
08.06-10
08.06-11A
08.06-11B
08.06-11C
08.06-12A
08.06-12B
08.06-12C
08.06-13A
08.06-13B
08.06-14A
08.06-14B
08.06-15A
08.06-15B
08.06-15C
08.06-15D
08.06-15E
08.06-16A
08.06-16B
08.06-22A
08.06-22B
DEC
DEM
DEP
DEF
SECTION 8 - SWITCHES AND PROTECTIVE DEVICES
TABLE OF CONTENTS
X
08.00-00A
08.10 SWITCHES - MANUAL
BYPASS SWITCHES
SWITCH MOUNTING IN VERTICAL DOUBLE CIRCUIT
SWITCH MOUNTING IN VERTICAL DOUBLE CIRCUIT
600 AMP DOUBLE CIRCUIT TIE SWITCH
600 AMP DOUBLE CIRCUIT TIE SWITCH
SWITCH ASSEMBLY, 300 AMP, SOLID BLADE, VERTICAL
SWITCH ASSEMBLY, 600 AMP, SOLID BLADE, VERTICAL
SWITCH ASSEMBLY, 600 AMP, SOLID BLADE, VERTICAL
SWITCH ASSEMBLY, 300 AMP, SOLID BLADE HORIZONTAL
SWITCH ASSEMBLY, 600 AMP, SOLID BLADE HORIZONTAL
600 AMP INLINE DISCONNECT
VERTICAL TANGENT CROSSING WITH 600 AMP DISCONNECTS
08.10-10
08.10-12A
08.10-12B
08.10-14A
08.10-14B
08.10-16
08.10-18A
08.10-18B
08.10-20
08.10-22
08.10-24
08.10-26
08.12 SWITCHES - LOAD CONTROL
VLR LOAD CONTROL SWITCH
VLR LOAD CONTROL SWITCH
VERSAVAC LOAD CONTROL
VERSAVAC LOAD CONTROL
CONNECTION DIAGRAM FOR VERSAVAC SWITCH
LOAD CONTROL SWITCH 600 AMP
LOAD CONTROL SWITCH 600 AMP
08.12-02A
08.12-02B
08.12-04A
08.12-04B
08.12-04C
08.12-06A
08.12-06B
08.13 SWITCHES - AUTOMATED
OVERHEAD AUTOMATIC TRANSFER SCHEME
VLR TYPE S TRANSFER CONTROL
AUTOMATIC TRANSFER SWITCH ASSEMBLY, (VLR), CONTROL WIRING DETAIL
SCADA MATE CX SWITCH STANDARD MOUNTING ARRANGEMENT
SCADA MATE CX SWITCH STANDARD MOUNTING ARRANGEMENT
SCADA MATE CX SWITCH STANDARD MOUNTING ARRANGEMENT
OMNI-RUPTER SWITCH CONTROL FACEPLATE
ANTENNA INSTALLATION FOR VERTICAL OMNI-RUPTER SWITCH
08.13-01
08.13-03
08.13-05
08.13-08A
08.13-08B
08.13-08C
08.13-10D
08.13-10E
FOR MAINTENANCE ONLY DRAWINGS
THE FOR MAINTENANCE ONLY DRAWINGS LISTED BELOW ARE NOT CONTAINED
IN THE PRINTED SPEC BOOK, BUT ARE AVAILABLE ONLINE
VERTICAL CONSTRUCTION TO VERTICAL CONSTRUCTION WITH
WITH OIL SECTIONALIZER (FMO)
SECTIONALIZER ASSEMBLY, OIL TYPE, VERTICAL (FMO)
RECLOSER ASSEMBLY, HORIZONTAL CONSTRUCTION (FMO)
RECLOSER ASSEMBLY, HORIZONTAL CONSTRUCTION (FMO)
HORIZONTAL CONSTRUCTION TO HORIZONTAL CONSTRUCTION WITH
OIL SECTIONALIZER (FMO)
RECLOSER ASSEMBLY, THREE-PHASE, HORIZONTAL 600 AMP SWITCH (FMO)
LOAD CONTROL SWITCH ASSEMBLY, (VLR), THREE-PHASE HORIZONTAL
WITH 600 AMP BYPASS (FMO)
OMNI-RUPTER SWITCH STANDARD MOUNTING ARRANGEMENT (FMO)
OMNI-RUPTER SWITCH STANDARD MOUNTING ARRANGEMENT (FMO)
OMNI-RUPTER SWITCH STANDARD MOUNTING ARRANGEMENT (FMO)
OMNI-RUPTER SWITCH STANDARD STACKED
DOUBLE-CIRCUIT POLE ARRANGEMENT (FMO)
OMNI-RUPTER SWITCH STANDARD STACKED
DOUBLE-CIRCUIT POLE ARRANGEMENT (FMO)
OMNI-RUPTER SWITCH HORIZONTAL MOUNTING ARRANGEMENT (FMO)
OMNI-RUPTER SWITCH HORIZONTAL MOUNTING ARRANGEMENT (FMO)
OMNI-RUPTER SWITCH HORIZONTAL MOUNTING ARRANGEMENT (FMO)
INTELLITEAM RADIO TRANSCEIVERS (FMO)
4
1/6/16
KATIGBAK
BURLISON
ADCOCK
3
8/27/15
KATIGBAK
BURLISON
ADCOCK
2
9/26/14
KATIGBAK
GUINN
ADCOCK
0
12/1/10
CECCONI
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
08.04-06
08.04-08
08.05-17A
08.05-17B
08.04-12
08.06-12
08.12-06
08.13-10A
08.13-10B
08.13-10C
08.13-11A
08.13-11B
08.13-13A
08.13-13B
08.13-13C
08.13-15
DEC
DEM
DEP
DEF
SECTION 8 - SWITCHES AND PROTECTIVE DEVICES
TABLE OF CONTENTS
X
08.00-00B
STANDARD PROCEDURES BULLETIN
STANDARD DISTRIBUTION ARRESTERS:
THE STANDARD DISTRIBUTION ARRESTER IS A DIRECT-CONNECTED METAL OXIDE ARRESTER WITH A GROUND
LEAD DISCONNECTOR ( DWG. 08.01-04 FOR DISCONNECTOR PROCEDURES).
METAL OXIDE ARRESTERS (MOV) HAVE BEEN PURCHASED SINCE 1984 AND OFFER THE BEST AVAILABLE
PROTECTION AGAINST LIGHTNING AND SWITCHING SURGES. BY DESIGN, THE MOV ARRESTER CONDUCTS A
SMALL LEAKAGE CURRENT (MILLIAMPS) TO GROUND UNDER NORMAL VOLTAGE CONDITIONS. SINCE 1990, ALL
OF OUR MOV ARRESTERS HAVE BEEN PURCHASED WITH POLYMER HOUSINGS. THE ADVANTAGE OF THE POLYMER
HOUSING IS THAT IT IS DESIGNED TO RETAIN THE BLOCKS DURING A CATASTROPHIC FAILURE MODE. THESE
MOV ARRESTERS ARE AVAILABLE IN THREE DIFFERENT CLASSIFICATIONS AS FOLLOWS:
RISER POLE ARRESTERS ARE USED ON PRIMARY UNDERGROUND CABLE RISERS. THESE ARRESTERS NORMALLY
CONTAIN LARGER BLOCKS THAN STANDARD DISTRIBUTION ARRESTERS TO PROVIDE ADDITIONAL PROTECTION
FOR THIS APPLICATION. THESE ARRESTERS ARE LABELED WITH THE WORDS "RP" AND THE VOLTAGE CLASS.
STANDARD DISTRIBUTION ARRESTERS ARE USED FOR OVERHEAD LINE AND EQUIPMENT PROTECTION. WHILE
THEY DO NOT HAVE A SPARK OVER VOLTAGE AS LOW AS THE RISER POLE ARRESTER, THEY PROVIDE AN
ECONOMICAL BIL MARGIN OF PROTECTION EXCEEDING THE OLD SILICONE CARBIDE ARRESTER.
TRANSFORMER ARRESTERS ARE IDENTICAL TO THE STANDARD DISTRIBUTION ARRESTER. THEY ARE
CATALOGED DIFFERENTLY TO INCLUDE A CONNECTION LEAD AND A GROUND STRAP TO CONNECT IT TO A
TRANSFORMER.
SILICONE CARBIDE ARRESTERS HAVE NOT BEEN PURCHASED SINCE 1984. THESE ARRESTERS CAN BE FOUND ON
THE SYSTEM WITH INTERNAL OR EXTERNAL GAP STRUCTURES. ALL SILICONE CARBIDE ARRESTERS HAVE
PORCELAIN HOUSINGS.
INTERNAL GAP ARRESTERS CONTINUE TO PROVIDE GOOD SURGE PROTECTION FOR THE SYSTEM AND SHALL
CONTINUE TO BE USED UNTIL THEY ARE REMOVED FOR ANY REASON. ONCE REMOVED, THEY SHALL BE
SCRAPPED.
EXTERNAL GAP ARRESTERS THAT ARE REMOVED SHALL BE SCRAPPED.
INSTALLATION PRACTICES:
1. ARRESTER LEAD LENGTHS (BOTH LINE AND GROUND LEADS) SHALL BE AS SHORT AND AS STRAIGHT AS
POSSIBLE. THIS PROVIDES THE BEST PROTECTION BY MINIMIZING THE SURGE VOLTAGE DURING ARRESTER
OPERATION. DO NOT COIL TRANSFORMER RISERS.
2. GROUND RODS SHALL BE INSTALLED AT ALL POLES CONTAINING ARRESTERS ACCORDING TO THE STANDARD
PROCEDURES OUTLINED ON DWGS. 01.01-01A , 01.01-01B, 01.01-01C AND 01.01-05.
ARRESTER APPLICATIONS
1. EQUIPMENT PROTECTION (GROUND PER DWGS. 01.01-01A , 01.01-01B, 01.01-01C AND 01.01-05) ALL
TRANSFORMERS, RECLOSERS, CAPACITOR BANKS, VOLTAGE REGULATORS, AND OTHER EQUIPMENT SHALL
HAVE ARRESTERS INSTALLED AS SHOWN ON THE APPROPRIATE SPECIFICATION DRAWINGS CONTAINED
HEREIN.
2. LINE PROTECTION
A. ALL NORMAL OPEN POINTS SHALL HAVE ARRESTERS INSTALLED ON EACH PHASE ON BOTH SIDES
(NORMAL SOURCE AND LOAD). ARRESTERS MAY BE MOUNTED ON POLE ADJACENT TO SWITCHES.
B. INSTALL ARRESTERS AT DEADENDS UNLESS PROTECTED BY EQUIPMENT ARRESTER.
C. INSTALL ARRESTERS EVERY 1400' TO 1600' UNLESS THERE ARE ARRESTERS PRESENT. ALSO, AREAS
WITH TALL TREES AND/OR BUILDINGS ALONG SIDE THE LINE ARE SHIELDED AND MIGHT REQUIRE LESS
REQUIRE LESS ARRESTERS AS PER ENGINEER'S JUDGMENT.
3
DEC
DEM
DEP
DEF
2
1
3/31/15
LOOSIER
WHITE
ADCOCK
0
8/16/10
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
X
DISTRIBUTION SURGE ARRESTERS
08.00-01
GENERAL
ON WOOD POLE CONSTRUCTION USE SINGLE COIL LOCKWASHER AND SQUARE WASHERS WITH CUTOUT,
ARRESTER AND SWITCH BRACKETS.
CUTOUTS
1. BYPASS FUSE HOLDERS OR NORMALLY OPEN CUTOUT DOORS SHOULD BE HUNG BY THEIR OPERATING RINGS
SO THE BARRELS WILL NOT FILL UP WITH WATER.
2. A TRANSFORMER STEM CONNECTOR MAY BE USED WHEN 1/0 OR SMALLER ALUMINUM WIRE IS RUN DIRECTLY
INTO THE CUTOUT.
3. WHEN ADDING CUTOUTS TO EXISTING VERTICAL CONSTRUCTION, THE PHASE TO PHASE SPACING SHOULD
BE 42 INCHES FOR 23KV.
ARRESTERS
1. ARRESTERS SHALL BE INSTALLED ON BOTH SIDES OF ANY NORMAL OPEN PRIMARY SWITCH DEVICE WHICH
CAN BE SOURCE FED FROM BOTH DIRECTIONS.
2. THE PRIMARY ARRESTER TAP SHOULD BE #6 BARE SOFT DRAWN SOLID COPPER WIRE.
3. ARRESTERS SHALL BE POSITIONED SUCH THAT A BLOWN DISCONNECTOR/ISOLATOR WILL NOT AFFECT OTHER
ENERGIZED EQUIPMENT.
4. ARRESTERS SHALL BE INSTALLED ON THE SOURCE AND LOAD SIDE OF RECLOSERS AND REGULATORS.
5. AT VOLTAGE REGULATOR INSTALLATIONS, INSTALL THE LIGHTNING ARRESTERS ON THE REGULATOR, IF
POSSIBLE. IF NOT POSSIBLE, MOUNT THE ARRESTERS AS CLOSE TO THE SOURCE AND LOAD BUSHINGS AS
POSSIBLE.
6. THE PRIMARY ARRESTER TAP CONNECTION CAN BE MADE WITH ALUMINUM HOT LINE ARRESTER CLAMPS.
STIRRUPS ARE NOT REQUIRED FOR ARRESTERS.
7. KEEP ARRESTER TAP AND GROUND LEADS AS SHORT AS POSSIBLE. THIS PROVIDES GREATER EQUIPMENT
PROTECTION.
8. AN ARRESTER SHOULD BE USED TO PROTECT ANY PHASE THAT HAS A GROUND WIRE EXTENDING PAST IT,
EXCEPT ON CONCRETE OR STEEL POLES.
9. ON UNDERGROUND SUBSTATION EXITS, DISTRIBUTION CLASS RISER POLE ARRESTERS SHALL BE LOCATED
ON THE TERMINAL POLE OUTSIDE THE SUBSTATION AND ON THE TERMINAL POLE IN THE SUBSTATION.
10. RISER POLE ARRESTERS SHALL BE USED ON ALL OVERHEAD TO UNDERGROUND DIP POLES.
11. INSTALL ARRESTERS EVERY 1400' TO 1600' UNLESS THERE ARE ARRESTERS PRESENT. ALSO, AREAS WITH
TALL TREES AND/OR BUILDINGS ALONG SIDE THE LINE ARE SHIELDED AND MIGHT REQUIRE LESS ARRESTERS
AS PER ENGINEER'S JUDGMENT.
12. CONCRETE OR METAL TRANSMISSION AND DISTRIBUTION POLES: INSULATE WITH 35KV INSULATORS AND
APPLY LIGHTNING ARRESTERS ON ALL PHASES EVERY 550'.
3
DEC
DEM
DEP
DEF
X
X
X
X
2
1
3/31/15
LOOSIER
WHITE
ADCOCK
0
11/29/10
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
CUTOUTS AND ARRESTERS GENERAL
08.00-03
3
1
2
4
BILL OF MATERIALS
MACRO UNIT
-
CU
ITEM
NO.
COMPATIBLE
UNIT
QTY
REQ'D
1
AREQOH10F
1
2
BKTCOLASTLXARMF
1
3
BKTCOLASNGSTLF
1
4
BKTCOLADBLSTLF
1
CATALOG
NUMBER
193511
220202
070101
311263
152106
013264
013308
070106
152106
013264
013308
QTY
PER
CU
2
1
1
1
2
2
2
1
2
2
2
DESCRIPTION
CABLE, 600V #6 SOLID SD CU
ARRESTER, LIGHTNING, 10KV, HD MOV
BRACKET, ARRESTER AND CUTOUT
BRACKET, SINGLE MOUNT
BOLT, MACHINE, 5/8" X 10"
WASHER, SPRING COIL, 5/8"
WASHER, 2-1/4" SQUARE
BRACKET, DOUBLE LIGHTNING ARR & CO
BOLT, MACHINE, 5/8" X 10"
WASHER, SPRING COIL, 5/8"
WASHER, 2-1/4" SQUARE
NOTES:
1. CAUTION: DO NOT TIGHTEN TOP NUT ON ARRESTERS WITH AN AIR OR HYDRAULIC SPEED WRENCH.
OVER-TORQUING CAN EASILY OCCUR USING THESE WRENCHES RESULTING IN A BROKEN CONTACT
INSIDE THE ARRESTER HOUSING.
3
2
ARRESTERS, 10 KV
1
0
8/31/10
REVISED
R
HOFFMAN
GUINN
ELKINS
DWG.
BY
CK'D
APPR.
08.01-01
PRIMARY RISER
ISOLATOR
CAUTION:
MAY BE ENERGIZED
AT PRIMARY
VOLTAGE
GROUND STRAP
GROUNDED
ROTATE ARRESTER TO
BE STRAIGHT OUT FROM
TANK
PROPERLY INSTALLED ARRESTER
FAILED ARRESTER
NOTES:
1. DIRECT CONNECTED ARRESTER LEADS ARE FURNISHED WITH AN EYE TERMINAL. THE LEAD IS TO BE CONNECTED
BETWEEN THE ARRESTER AND THE PRIMARY BUSHING TERMINAL WITH THE EYE TERMINAL BETWEEN THE NUT
AND THE TERMINAL, AND ARRANGED SO AS NOT TO INTERFERE WITH THE PRIMARY RISER
2. IN THE EVENT OF AN ARRESTER FAILURE, THE ISOLATOR WILL OPERATE AND DISCONNECT THE GROUND LEAD,
THUS PREVENTING AN INTERRUPTION TO THE CIRCUIT. ALL FAILED ARRESTERS ARE TO BE REPORTED TO THE
LOCAL OPERATIONS CENTER. THE ARRESTER IS TO BE CHANGED OUT AS SOON AS POSSIBLE AFTER BEING
REPORTED.
3. ON NEW POLE MOUNTED SINGLE-PHASE TRANSFORMERS, THE TRANSFORMER IS SHIPPED WITH THE LIGHTNING
ARRESTER ROTATED UP AGAINST THE TANK. THIS IS DONE TO PREVENT BREAKAGE OF THE ARRESTER DURING
SHIPPING. BEFORE THE TRANSFORMER IS INSTALLED, THE ARRESTER MOUNTING BOLT SHOULD BE LOOSENED
AND THE ARRESTER ROTATED UNTIL IT IS STRAIGHT OUT FROM THE TANK. IF THIS IS NOT DONE AND THE
ARRESTER IS LEFT UP AGAINST THE TANK, IT WILL EVENTUALLY CAUSE MOMENTARY FEEDER OPERATIONS OR
OUTAGES.
4. CAUTION: DO NOT TIGHTEN TOP NUT ON ARRESTERS WITH AN AIR OR HYDRAULIC SPEED WRENCH. OVERTORQUING CAN EASILY OCCUR USING THESE WRENCHES RESULTING IN A BROKEN CONTACT INSIDE THE
ARRESTER HOUSING.
3
2
APPLICATION OF DIRECT CONNECTED ARRESTERS
1
0
7/11/10
REVISED
GUINN
GUINN
ELKINS
BY
CK'D
APPR.
ON DISTRIBUTION TRANSFORMERS
DWG.
08.01-04
2
3
1
5
4
C
H
A
N
C
E
CROSSARM MOUNTED CIRCUIT
POLE MOUNTED CUTOUT
FOR MAINTENANCE ONLY
BILL OF MATERIALS
MACRO UNIT
-
CU
ITEM
NO.
1
1
1
1
1
1
1
1
1
COMPATIBLE
UNIT
QTY
REQ'D
CATALOG
NUMBER
FUSE15CO100F
TFUSE15CO100F
FUSE27CO100F
FUSE27CO100PF
TFUSE27CO100F
TFUSE27CO100PF
FUSE27CO200F
SW153COSBDF
SW253COSBDF
1
1
1
1
1
1
1
1
1
2
BKTCOLASTLXARMF
1
3
BKTCOLASNGSTLF
1
4
BKTCOLADBLSTLF
1
5
5
SW153COSBDBOF
SW253COSBDBOF
1
1
221112
221112
221139
9220090063
221139
9220090063
221143
9220210916
9220210993
070101
011213
311263
013264
013308
152106
070106
013264
013308
152106
269046
269043
QTY
PER
CU
1
1
1
1
1
1
1
1
1
1
2
1
2
2
2
1
2
2
2
1
1
DESCRIPTION
CUTOUT, NONLOADBREAK, 15KV, 100A, 16KA, 110KV BIL
CUTOUT, NONLOADBREAK, 15KV, 100A, 16KA, 110KV BIL
CUTOUT, NONLOADBREAK, CUTOUT, 27KV, 100A, 12KA, 150KV BIL
CUTOUT, SILICONE, 27KV, 100A, 12KA, 150KV BIL, SILICON
CUTOUT, NONLOADBREAK, CUTOUT, 27KV, 100A, 12KA, 150KV BIL
CUTOUT, SILICONE, 27KV, 100A, 12KA, 150KV BIL, SILICON
CUTOUT, NONLOADBREAK, CUTOUT, 27KV, 200A, 10KA, 150KV BIL
CUTOUT, BLADE, BLADE,SLD,NONLOADBREAK,300A,15 KV
CUTOUT, BLADE, SLD, NONLOADBREAK BLADE,300A,25 KV, 150 KV BIL
BRACKET, LA & CO TY A
BOLT, CARRIAGE, 3/8 IN, 6 IN, CARBON STEEL, ASTM A153, CRG 3
BRACKET, .., SGL MT
WASHER, .., SPRING,COIL,STEEL,FOR,5/8",BOLT,GALV.
WASHER, SQUARE, 2-1/4",SQUARE,FLAT,13/16",HOLE,GALV.
BOLT, MACHINE, 5/8 IN, 10 IN, STEEL, A-ASTM A307, GLV, MACH,
BRACKET, .., ARSTR & CO,DBL MNTG
WASHER, .., SPRING,COIL,STEEL,FOR,5/8",BOLT,GALV.
WASHER, SQUARE, 2-1/4",SQUARE,FLAT,13/16",HOLE,GALV.
BOLT, MACHINE, 5/8 IN, 10 IN, STEEL, A-ASTM A307, GLV, MACH,
BLADE, CUTOUT, BLADE SOLID, CUTOUT, 15KV, 300A
BLADE, CUTOUT, BLADE, SOLID, CUTOUT, 27KV, 300A
NOTES:
1. USE FUSE (FUSE____F) FOR OVERHEAD AND UNDERGROUND LINE CUTOUTS. USE TFUSE ( TFUSE____F)
FOR TRANSFORMER AND CAPACITOR BANKS. THIS ENSURES PROPER ACCOUNTING IN WMIS.
2. 27KV CUTOUTS ARE REQUIRED ON THE 25KV SYSTEM IN HOLOPAW, ON ALL CONCRETE POLES AND IN
COASTAL/CONTAMINATED AREAS.
3. USE 100 AMP CUTOUT DOORS WITH 103 FUSE LINKS AND SMALLER. USE 200 AMP CUTOUT DOORS WITH
125, 150, AND 200 AMP FUSE LINKS. DO NOT USE 200 AMP CUTOUT DOORS WITH 103 OR SMALLER FUSES.
3
2
CUTOUTS AND BRACKETS
R
1
2/6/12
BURLISON
0
10/12/10
HOFFMAN
GUINN
ELKINS
DWG.
BY
CK'D
APPR.
08.01-10
REVISED
BURLISON
ELKINS
1
2
BILL OF MATERIALS
CU
ITEM
NO.
1
COMPATIBLE
UNIT
QTY
REQ'D
CATALOG
NUMBER
FUSE15CO100F
2 OR 3
2
BKTCOLATRISTLF
1
221112
070104
013264
013308
152107
QTY
PER
CU
1
1
2
2
2
DESCRIPTION
CUTOUT, 15 KV 100A, 16KA ASYMMETRICAL
BRACKET, LA, CUTOUT, 48"
WASHER, SPRING COIL, 5/8"
WASHER, 2-1/4" SQUARE
BOLT, MACHINE, SQ, NUT, 5/8" X 12"
3
2
1
4/9/13
McCONNELL
0
8/30/10
GUINN
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
DANNA
ADCOCK
CUTOUTS AND ARRESTERS
2 OR 3 EACH ON TRIPLE
MOUNTING BRACKET
DWG.
08.01-11
1
3
4
CONNECTOR STEM
INCLUDED WITH
TERMINATOR KIT
2
BILL OF MATERIALS
MACRO UNIT
CU
ITEM
NO.
1
COMPATIBLE
UNIT
QTY
REQ'D
CATALOG
NUMBER
FUSE15CO100F
1
2
ARUGTP10F
1
3
BKTCOLASNGSTLF
1
4
KHLC40N6F
1
221112
220208
153534
311263
013264
013308
152106
9220184790
CA1T15FM
OR
CA2T15FM
(TWO-PHASE)
QTY
PER
CU
1
1
1
1
2
2
2
1
DESCRIPTION
CUTOUT, LOADBREAK, 15KV, 100A, 16KA, 110KV BIL
ARRESTER, LIGHTNING, RP, 10KV, FOR TRANSITION POLES, HD
CONNECTOR, STEM, ARRESTER
BRACKET, SGL MT
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
WASHER, SQUARE, 2-1/4", SQUARE, FLAT, 13/16" HOLE, GALV.
BOLT, MACHINE, 5/8" X 10", STEEL, A-ASTM A307, GALV.
CLAMP, HOT LINE, ALUM, SMALL, 4/0
NOTES:
1. CAUTION: DO NOT TIGHTEN TOP NUT ON ARRESTERS WITH AN AIR OR HYDRAULIC SPEED WRENCH.
OVER-TORQUING CAN EASILY OCCUR USING THESE WRENCHES RESULTING IN A BROKEN CONTACT
INSIDE THE ARRESTER HOUSING.
3
2
1
6/7/13
0
11/5/10
REVISED
DANNA
ADCOCK
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
CUTOUTS AND ARRESTERS
SINGLE-PHASE TERMINATION
ON POLE MOUNTED "L" BRACKET
DWG.
08.01-12
1
3
4
2
BILL OF MATERIALS
MACRO UNIT
CU
ITEM
NO.
1
COMPATIBLE
UNIT
QTY
REQ'D
CATALOG
NUMBER
FUSE15CO100F
3
2
ARUGTP10F
3
3
BKTCOLATR1STLF
1
4
KHLC40N6F
3
221112
220208
153534
070104
013264
013308
152106
9220184790
CA3T15FM
QTY
PER
CU
1
1
1
1
2
2
2
1
DESCRIPTION
CUTOUT, LOADBREAK, 15KV, 100A, 16KA, 110KV BIL
ARRESTER, LIGHTNING, RP, 10KV, FOR TRANSITION POLES, HD
CONNECTOR, STEM, ARRESTER
BRACKET, LA AND CO TRI MNTG
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
WASHER, SQUARE, 2-1/4", SQUARE, FLAT, 13/16" HOLE, GALV.
BOLT, MACHINE, 5/8" X 10", STEEL, A-ASTM A307, GALV.
CLAMP, HOT LINE, ALUM, SMALL, 4/0
NOTES:
1. CAUTION: DO NOT TIGHTEN TOP NUT ON ARRESTERS WITH AN AIR OR HYDRAULIC SPEED WRENCH.
OVER-TORQUING CAN EASILY OCCUR USING THESE WRENCHES RESULTING IN A BROKEN CONTACT
INSIDE THE ARRESTER HOUSING.
3
2
1
6/7/13
0
11/5/10
REVISED
DANNA
ADCOCK
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
CUTOUT AND ARRESTER,
(2) OR (3) PHASE TERMINATION
ON TRIPLE MOUNTING BRACKET
DWG.
08.01-13
KHLC40N6F
OR
KHLC7933F
#2 WP COPPER
CU RCRISERN2CUF
5"
4"
4"
14"
6"
36"
14"
36"
14"
72"
4"
NEUTRAL
FRONT VIEW
NOTES:
1. SEE DWG 03.06-04 FOR POST TYPE INSULATORS.
2. SEE DWG. 03.06-08 FOR PIN TYPE INSULATORS.
3. SEE DWG. 03.03-04 FOR SLACK SPAN CLAMPS.
4. SEE DWG. 03.16-00 FOR SLACK SPAN GRIPS.
3
DEC
DEM
DEP
DEF
2
1
8/7/14
SALAS
DANNA
ADCOCK
0
11/9/12
HOFFMAN
DANNA
ADCOCK
BY
CK'D
APPR.
REVISED
X
SLACKSPAN WITH FUSED CUTOUT
08.01-14
SOURCE
LOAD
5
PLAN VIEW
5"
36"
4
3
36"
2
1
4"
6"
CL TOP BOLT OF BRACKET
72"
NEUTRAL
#6 SD BC
FRONT VIEW
BILL OF MATERIALS
MACRO UNIT
CU
ITEM
NO.
COMPATIBLE
UNIT
QTY
REQ'D
1
ISEYEBOLT5812F
3
2
3
4
5
ISEYENUT58F
DECLMP(WIRE)F
IDES(KV)F
BKTCO18FGF
3
6
6
3
-
ITEM
NUMBER
11709
13346
12210
9220275817
QTY
PER
CU
1
1
1
1
1
1
DESCRIPTION
BOLT, OVAL EYE, 5/8" X 12"
WASHER, 3" SQ., CURVED, 13/16" HOLE
INSULATOR SUPPORT EYENUT
DEADEND CLAMP (WIRE)
INSULATOR DEADEND SUSPENSION (KV) POLYMER
BRACKET, STANDOFF, 1.5" RND X 18" LG IN, FIBERGLASS
NOTES:
1. THIS DESIGN SPECIFICATION CAN ALSO BE APPLIED TO A SINGLE-PHASE CONFIGURATION.
3
DEC
DEM
DEP
DEF
2
0
X
VERTICAL DOUBLE DEADEND WITH CUTOUTS
1
8/10/15
REVISED
LOOSIER
BURLISON
ADCOCK
BY
CK'D
APPR.
08.01-16
TANGENT CONSTRUCTION
DEADEND CONSTRUCTION
CN 080212
PLAN VIEW
CN 9220184790 OR
CN 9220184794
PLAN VIEW
5"
8"
8" TYP.
#6 WP COPPER
CU ARRRISERN6CUF
CN 9220218856
36"
CN 220202
36"
4" TYP. TO
GUY ATTACHMENT
8"
36"
36"
#6 SD BC
SEE NOTE 1
SEE NOTE 1
8"
72"
72"
NEUTRAL
NEUTRAL
#6 SD BC
FRONT VIEW
#6 SD BC
FRONT VIEW
NOTES:
1. INSTALL GROUND AWAY FROM INSULATOR.
3
6/6/14
LOOSIER
DANNA
ADCOCK
2
5/24/13
McCONNELL
DANNA
ADCOCK
1
3/2/11
BURLISON
BURLISON
ELKINS
0
8/11/10
ROBESON
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
DEC
DEM
DEP
VERTICAL CONSTRUCTION
WITH LIGHTNING ARRESTER
DEF
X
08.01-28
5"
4" TYP.
36"
TOP BRACKET BOLT
36"
36" MIN.
10"
PLAN VIEW
64"
NEUTRAL
FRONT VIEW
NOTES:
1. SEE SECTION 01 FOR ADDITIONAL GROUNDING DETAILS.
3
2
DOUBLE CIRCUIT CONSTRUCTION
R
1
0
11/29/10
REVISED
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
WITH LIGHTNING ARRESTER
DWG.
08.01-29
6"
8"
18"
KHLC40N6F
OR
KHLC7933F
16"
34"
8"
6"
PLAN VIEW
PLAN VIEW
8"
34"
16"
18"
8"
6"
4"
6"
4"
36"
#2 WP COPPER
CU RCRISERN2CUF
72"
78
"G
U
YS
TI
CK
6"
72"
#6 SD BC
NEUTRAL
4"
#6 SD BC
FRONT VIEW
FRONT VIEW
NOTES:
1. CUTOUTS WILL NORMALLY BE INSTALLED ON THE TAP POLE.
3
2
DEC
8/7/14
SALAS
DANNA
1
8/31/11
BURLISON
BURLISON
ELKINS
0
8/11/10
ROBESON
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
ADCOCK
DEM
DEP
HORIZONTAL CONSTRUCTION TO
HORIZONTAL DEADEND
DEF
X
08.01-32
6"
16"
6"
16"
NEUTRAL
42"
6"
NEUTRAL
PLAN VIEW
#2 WP COPPER
CU RCRISERN2CUF
36"
KHLC40N6F
OR
KHLC7933F
62"
GU
YA
TT
AC
HM
EN
T
6"
NEUTRAL
4"
#6 SD BC
FRONT VIEW
3
2
8/7/14
SALAS
DANNA
ADCOCK
1
8/31/11
BURLISON
BURLISON
ELKINS
0
8/11/10
ROBESON
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
HORIZONTAL CONSTRUCTION TO
HORIZONTAL WITH CUTOUT
(FLYING TAP)
DEC
DEM
DEP
DEF
X
08.01-33
TANGENT CONSTRUCTION
DEADEND TO DEADEND
SOURCE
NEUTRAL
LOAD
PLAN VIEW
PLAN VIEW
KHLC40N6F
OR
KHLC7933F
6"
36"
#2 WP COPPER
CU RCRISERN2CUF
TOP BOLT OF
'L' BKT
2"
GUY ATTACHMENT
AND 78" GUY STICK
72"
78
"G
UY
ST
I
CK
4"
72"
FRONT VIEW
NEUTRAL
4"
FRONT VIEW
3
DEC
2
8/7/14
SALAS
DANNA
ADCOCK
1
8/31/11
BURLISON
BURLISON
ELKINS
0
8/11/10
ROBESON
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
DEM
DEP
HORIZONTAL CONSTRUCTION TO
BRANCH LINE
DEF
X
08.01-36
IN-LINE CONSTRUCTION
DEADEND CONSTRUCTION
GUY ATTACHMENT
PLAN VIEW
PLAN VIEW
9"
4"
9"
35"
15"
20"
9"
4"
6"
9"
9"
24"
33"
6"
9"
5"
6"
SEE
DETAIL 'A'
62"
GUY
ATTACHMENT
72"
#6 SD BC
#6 SD BC
FRONT VIEW
FRONT VIEW
#6 SD BC
NOTES:
1. SEE SECTION 01 FOR ADDITIONAL GROUNDING DETAILS.
DETAIL 'A'
3
2
HORIZONTAL CONSTRUCTION WITH
R
1
0
11/29/10
REVISED
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
LIGHTNING ARRESTER
DWG.
08.01-37
KHLC40N6F
OR
KHLC7933F
TOP
BRACKET
BOLT
5"
3"
#2 WP COPPER
CU RCRISERN2CUF
6"
12"
3"
BOTTOM
BRACKET
BOLT
4"
IDES25PF
72"
(SEE NOTE 5)
4"
4"
CL OF BOLT HOLE
#6 SD BC
FRONT VIEW
12KV
NOTES:
1. POLE GAINS ( ISGAINGRIDF FOR 15/25KV INSULATORS OR ISGAINGRID55F FOR 35KV INSULATORS) ARE REQUIRED
FOR POST INSULATOR INSTALLATIONS ON WOOD POLES WHEN THE POLE DOES NOT HAVE A SLAB GAIN FOR ALL
CONDUCTOR SIZES.WHEN THE CONDUCTOR IS 336.4 KCMIL OR LARGER, USE POLE GAIN EVEN IF SLAB GAIN
EXISTS. POLE GAINS ARE NOT REQUIRED FOR INSULATORS USED FOR JUMPERS. SLACK SPANS WITH 336 AND
795 CONDUCTORS REQUIRE A POLE GAIN.
2. TYPICAL INSTALLATION: SEE SECTION 04 FOR NEUTRAL/SECONDARY DETAILS.
3. TYPICAL INSTALLATION: SEE SECTION 02 FOR GUYING DETAILS.
4. SEE DWG. 08.01-10 FOR BILL OF MATERIALS FOR CUTOUTS.
5. 72" NEUTRAL SPACING IS PREFERRED TO ACCOMMODATE MAINTENANCE AND SHOULD BE OBTAINED ON
NEW CONSTRUCTION OR UPGRADE INVOLVING POLE REPLACEMENT. UPGRADES AND ADDITIONS ON
EXISTING POLES MAY UTILIZE 60" NEUTRAL SPACING IF 72" SPACING CANNOT BE OBTAINED WITHOUT
REPLACING THE POLE OR CAUSING CONFLICT WITH COMMUNICATION CABLES.
6. SEE DWG. 03.06-02 FOR BOLTS AND LINE CLAMPS.
3
DEC
2
8/7/14
SALAS
DANNA
ADCOCK
1
3/21/13
McCONNELL
DANNA
ADCOCK
0
11/8/12
HOFFMAN
DANNA
ADCOCK
BY
CK'D
APPR.
REVISED
DEM
DEP
DEF
X
SINGLE-PHASE CONSTRUCTION - FUSED TAP
08.01-38
KHLC40N6F
OR
KHLC7933F
TOP
BRACKET
BOLT
5"
3"
#2 WP COPPER
CU RCRISERN2CUF
6"
12"
3"
BOTTOM
BRACKET
BOLT
4"
1ST PHASE
POSITION
IN
S
UL
AT
OR
36"
12
0"
GU
Y
FUSE15CO100F
IDES25PF
2ND PHASE
POSITION
78
"G
UY
IN
SU
LA
TO
R
36"
IN
SU
L
AT
O
R
3RD PHASE
POSITION
78
"G
UY
72"
4"
4"
12 KV
NOTES:
1. MIDDLE CUTOUT CAN BE PLACED ON SAME SIDE OF POLE AS OTHER CUTOUTS.
2. FOR FEEDER TAPS, THE CUTOUTS ARE OMITTED, BUT THE SPACING FOR THE TAP IS THE SAME.
3. SEE DWG. 03.06-02 FOR BOLTS AND LINE CLAMPS.
3
DEC
2
DEM
DEP
VERTICAL CONSTRUCTION - TANGENT
1
8/7/14
SALAS
DANNA
ADCOCK
0
11/8/12
HOFFMAN
DANNA
ADCOCK
BY
CK'D
APPR.
REVISED
FUSED TAP CONSTRUCTION
DEF
X
08.01-39
TRADITIONAL NON-LOADBREAK SECTIONALIZER
USER SETABLE NON-LOADBREAK SECTIONALIZER
COLOR CODED BANDS
* SEE QUICK REFERENCE MANUAL FOR
TOP
USER OPERATING INSTRUCTIONS.
NO BAND = 2 COUNT
GREEN BAND = 3 COUNT
BOTTOM
BROWN BAND = 100 AMP
NO BAND = 200 AMP
RESETTABLE SECTIONALIZER
RESETTING TRADITIONAL SECTIONALIZERS
CAP
ELECTRONICS
LOWER
TRUNION
INSERT THE OPENING OF AN ADJUSTABLE WRENCH INTO THE HOLE
ON THE BACK OF THE TRUNION. ROTATE THE TRUNION WITH THE
WRENCH UNTIL TRUNION DOOR IS COMPLETELY SHUT. SLOWLY,
REMOVE THE WRENCH FROM THE TRUNION. THE TRUNION WILL
SNAP OPEN IF IT IS NOT FULLY CLOSED.
BILL OF MATERIALS
CU
ITEM
NO.
1
2
3
4
5
6
MACRO
UNIT
-
COMPATIBLE
UNIT
QTY
REQ'D
CATALOG
NUMBER
SECT15E100S2F
SECT15E100S3F
SECT15E200S2F
SECT15E200S3F
SECT27E100S2F
SECT15EABBF
1
1
1
1
1
1
300601
9220108582
9220108583
9220109650
9220086479
9220181861
QTY
PER
CU
1
1
1
1
1
1
DESCRIPTION
SECTIONALIZER,
SECTIONALIZER,
SECTIONALIZER,
SECTIONALIZER,
SECTIONALIZER,
SECTIONALIZER,
15KV,
15KV,
15KV,
15KV,
25KV,
15KV,
NLBK,
NLBK,
NLBK,
NLBK,
NLBK,
NLBK,
1-PH,
1-PH,
1-PH,
1-PH,
1-PH,
1-PH,
100A, 2-SHOT, NO CUTOUT
100A, 3-SHOT, NO CUTOUT
200A, 2-SHOT, NO CUTOUT
200A, 3-SHOT, NO CUTOUT
100A, 2-SHOT, NO CUTOUT
USER SETABLE, NO CUTOUT
NOTES:
1. SECTIONALIZERS WILL FIT IN A STANDARD NLB INTERCHANGEABLE CUTOUT.
2. SECTIONALIZERS HAVE NO FAULT CURRENT INTERRUPTING CAPABILITY. THEY RELY ON THE SOURCE SIDE
BREAKER OR RECLOSER TO OPEN DURING THE FAULT. THE SECTIONALIZER OPENS WHILE THE BREAKER/
RECLOSER IS OPEN. THEY DO NOT RELY ON FAULT CURRENT FOR COORDINATION; THEREFORE THEY ARE
USEFUL WHERE COORDINATION PROBLEMS EXIST.
3. SECTIONALIZER COUNTS WHEN LINE CURRENT DROPS BELOW 300 mA.
4. CONTACT YOUR SYSTEM ENGINEER PRIOR TO INSTALLATION ON MULTI-PHASE LOCATIONS.
5. ITEM 6 - SEE QUICK REFERENCE MANUAL FOR OPERATING INSTRUCTIONS.
3
2
ELECTRONIC RESETTABLE SECTIONALIZERS
R
1
6/16/11
HOFFMAN
0
9/20/10
HOFFMAN
GUINN
ELKINS
DWG.
BY
CK'D
APPR.
08.04-02
REVISED
BURLISON
ELKINS
RECLOSERS, SECTIONALIZERS, TRANSFERS
GENERAL
1. USE THE SUPPLIED GROUNDING CONNECTOR ON THE OIL SECTIONALIZER TANK AND RECLOSER TANK TO
GROUND THE UNIT TO THE ARRESTER DOWN LEAD.
2. A LOAD BREAK TOOL SHOULD BE USED TO OPEN DRY TYPE SECTIONALIZERS AND RECLOSER BYPASS
SWITCHES.
3. FOR VERTICAL CONSTRUCTION THE MINIMUM TANK CLEARANCE BETWEEN SINGLE-PHASE RECLOSER TANKS
AND ADJACENT RECLOSER BUSHINGS IS TO BE 13 INCHES.
4. FOR THREE-PHASE RECLOSERS, THE GROUND TRIP SHORTING SWITCH OPERATES AS FOLLOWS:
A. SWITCH-UP - THE GROUND TRIP IS CUT OUT
B. SWITCH DOWN - THE GROUND TRIP IS CUT IN
5. THE THREE-PHASE RECLOSER MAY BE REVERSED IN THE MOUNTING BRACKET TO ACCOMMODATE THE
SOURCE TO LOAD DIRECTION OF FEED THROUGH THE RECLOSER.
3
2
1
0
11/29/10
REVISED
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
RECLOSERS, SECTIONALIZERS, TRANSFERS AND
THREE-PHASE RECLOSER LIGHTNING ARRESTER
MOUNTING DETAIL
R
DWG.
08.05-00
SEQUENCE
2A2B
2A2C
2A2D
1A3B
1A3C
1A3D
1A2B
1A2C
1A2D
SINGLE-PHASE RECLOSERS
OPERATING SEQUENCE
TWO FAST FOLLOWED BY TWO RETARDED
TWO FAST FOLLOWED BY TWO EXTRA RETARDED
TWO FAST FOLLOWED BY TWO STEEP RETARDED
ONE FAST FOLLOWED BY THREE RETARDED
ONE FAST FOLLOWED BY THREE EXTRA RETARDED
ONE FAST FOLLOWED BY THREE STEEP RETARDED
ONE FAST FOLLOWED BY TWO RETARDED
ONE FAST FOLLOWED BY TWO EXTRA RETARDED
ONE FAST FOLLOWED BY TWO STEEP RETARDED
CURVE(S)
A AND B
A AND C
A AND D
A AND B
A AND C
A AND D
A AND B
A AND C
A AND D
TYPE - AMPS
RATING, 2"
MFG. SERIAL
NUMBER, 2"
OPERATING CURVES,
3"
INCLUDED RECLOSERS:
H, 4H, L, V4L AND E
CATALOG NUMBER,
2" UP TO 10 DIGITS
NON-PCB
CERTIFICATION, 2"
MAINTENANCE DATE, 1"
SINGLE-PHASE RECLOSERS
1 - PHASE TRIP COIL SIZE: 100, 160, 185, 225, 280, 400, 400X, 560, 560X
2 - PHASE TRIP TIME DELAY CURVE: B, C, D OR E-CURVE
3 - PHASE TRIP OPERATING SEQUENCE:
A. NUMBER OF OPERATIONS ON A-CURVE
B. NUMBER OF OPERATIONS ON DELAYED B, C, D OR E-CURVE
4 - BUSHING CT RATIO:
100 (100:5) 200(200:5) 300(300:5)
400 (400:5) 500(500:5) 600(600:5)
5 - GROUND TRIP TIME DELAY CURVE: 2 3
6 - GROUND TRIP FAST OPEN OPERATIONS: 1 2 3 4
7 - GROUND TRIP SOLENOID CONNECTION: 1 (SERIES) 2 (PARALLEL)
8 - CATALOG NUMBER (UP TO 10 DIGITS)
9 - MANUFACTURER'S SERIAL NUMBER
10 - MAINTENANCE DATE
11 - NON-PCB CERTIFICATION (ON END WITH OPERATING HANDLE)
3A
1
3B
400-2A2D
3"
CNCNCNCNCN
8
11
6
3"
9
XX-XX
4
5
10
7
INCLUDED RECLOSERS:
VW AND WV
THREE-PHASE HYDRAULIC RECLOSERS
ALL HYDRAULICS - NOT VACUUM UNITS
1
2
3
4
5
-
CATALOG NUMBER (UP TO 10 DIGITS)
MANUFACTURER'S SERIAL NUMBER
MANUFACTURER'S TYPE RECLOSER: VWE, VR3S AND OVR
FULL-LOAD CURRENT RATING (560, 630, 800)
MAINTENANCE DATE
2
NOTES:
5
1. STENCIL THE CATALOG NUMBER ON THE OUTSIDE, PADLOCK
SIDE OF THE RECLOSER ELECTRONIC CONTROL CABINET.
SNSNSNSN
VR3S-560
CNCNCNCN
3
4
1
THREE-PHASE ELECTRONIC CONTROLLED RECLOSERS
1
2
3
4
-
AMPERE RATING
COUNTS TO OPEN OR SHOTS TO LOCKOUT
MAINTENANCE DATE
CATALOG NUMBER, 2"
HANGER ON BACK SIDE
OF SECTIONALIZER
1
NOTES:
1. SEE DWG. 08.04-02 FOR ELECTRONIC SECTIONALIZERS.
3
CNCN
2
4
HYDRAULIC SECTIONALIZERS
3
2
RECLOSER IDENTIFICATION
1
0
11/29/10
REVISED
R
GUINN
GUINN
HOYT
DWG.
BY
CK'D
APPR.
08.05-01
B
B
A
A
12"
C
C
DIMENSIONS
TYPE 4H, L, V4L, E AND 4E RECLOSERS
DIMENSIONS
TYPE H RECLOSER
RECLOSER TYPE
DIMENSION
(IN.)
4H
L
V4L
E
4E
H
A
36
37
45
42
49
30
B
17
19
19
20
23
16
C
7
6
15
9
15
14
WEIGHT WITH OIL
(LBS.)
114
159
205
169
205
85
OIL CAPACITY
(GAL.)
5
7
9.5
8.2
9.5
4
NOTES:
1. THE DIMENSIONS, WEIGHTS AND CAPACITIES LISTED ABOVE ARE APPROXIMATE.
3
DEC
2
DEM
DEP
TYPICAL SINGLE-PHASE RECLOSER
1
11/17/15
LOOSIER
BURLISON
ADCOCK
0
11/29/10
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
DIMENSIONS, WEIGHTS AND OIL CAPACITIES
DEF
X
08.05-02
CLOSED
G
N N
O I
N OS
L
VIEW OF LEVER
CONTROL MECHANISM
C
RE
O
P
E
N
RETURN TO
"UP" POSITION
AFTER USE
SET LEVER IN THIS
POSITION FOR
NONRECLOSING
NON-AUTOMATIC RECLOSING LEVER
NOTES:
1. NON-AUTOMATIC RECLOSING LEVER FOR COOPER RECLOSERS PROVIDES ONE-SHOT LOCKOUT OF THE RECLOSER
WHEN TRIPPED ELECTRICALLY. IT IS CONTROLLED BY AN ADDITIONAL LEVER UNDER THE OPERATING HANDLE
HOOD WHICH, WHEN PULLED DOWN, ENGAGES THE LOCKOUT AND PLUNGER MECHANISMS, BYPASSING THE
HYDRAULIC LOCKOUT IN SUCH A MANNER THAT WHEN THE SOLENOID PLUNGER IS PULLED DOWN, THE
LOCKOUT MECHANISM IS TRIPPED. IN ORDER FOR THE RECLOSER TO RESUME NORMAL, FULL-AUTOMATIC
OPERATION, THE LEVER IS MOVED BACK TO THE "UP" POSITION. THE LEVER OPERATES ON A TOGGLE SO THAT
IT IS POSITIVELY IN THE NON-AUTOMATIC OR AUTOMATIC POSITION.
2. AFTER USE, THE NON-AUTOMATIC RECLOSING LEVER MUST BE RETURNED TO NORMAL "UP" POSITION TO
PROVIDE AUTOMATIC RECLOSING
TO CLOSE, PLACE HOTSTICK TIP
AGAINST MANUAL OPERATING
HANDLE AND PUSH UPWARD
TO OPEN, INSERT HOTSTICK
TIP INTO EYELET OF MANUAL
OPERATING HANDLE AND PULL
DOWNWARD.
3
2
COOPER RECLOSERS
1
0
7/31/14
REVISED
GUINN
GUINN
ADCOCK
BY
CK'D
APPR.
OPERATING LEVERS
DEC
DEM
DEP
DEF
X
X
X
X
08.05-06
PLAN VIEW
5"
LOAD
SOURCE
6"
3
26"
4
2
1
54"
SEE DWG. 08.05-15B
28"
6"
26"
54"
28"
#2 SD BC
6"
26"
ALL ENERGIZED
PARTS SHOULD
BE COVERED TO
GUARD AGAINST
DAMAGE CAUSED
BY ANIMALS
#2 SD BC
72"
46"
FUSES
STORED WITH
BARRELS DOWN
ON 3" STAPLE
#2 SD BC
#6 SD BC
FRONT VIEW
SIDE VIEW
BILL OF MATERIALS
MACRO UNIT
-
CU
ITEM
NO.
1
2
3
4
COMPATIBLE
UNIT
FUSE15CO100F
SW153COSBDF
KHLC40N6F
RCRISERN2CUF
QTY. REQ'D.
1
2
2
1
2
4
4
2
ITEM
NUMBER
3
6
6
3
221112
9220210916
9220184790
9220218857
QTY
PER
CU
1
1
1
12 FT.
DESCRIPTION
CUTOUT, LB, 15KV, 100A, 16KA, 110KV BIL
CUTOUT, BLADE, SLD
CLAMP, HOT LINE, ALUMINUM, SMALL
WIRE, COPPER, #2, SOLID, 600V, SD COPPER
NOTES:
1. ISSUE RECLOSER SEPARATELY. RECLOSER WILL COME WITH ARRESTERS PRE-MOUNTED.
*2. FOR ALL V4L RECLOSER INSTALLATIONS ON VERTICAL CONSTRUCTION, INCREASE THE PHASE SPACING BETWEEN THE PRIMARY
CONDUCTORS FROM 54" TO 64" AND INCREASE THE 28" DIMENSIONS TO 38".
3. SEE DWG 08.05-15B FOR BRACKET DETAILS AND BILL OF MATERIALS.
4. FOR SINGLE-PHASE AND TWO-PHASE INSTALLATIONS, USE SPACING REQUIREMENTS FROM BOTTOM UNIT CLOSEST TO NEUTRAL
TOWARDS THE TOP OF THE POLE.
5. EQUIPMENT CASE GROUND TO NEUTRAL TO BE #2 SD BC.
6. IF RECLOSERS ARE USED IN MAINLINE FEEDER (336 OR 795), USE 600 AMP RECLOSER BYPASS (SEE DWG. 08.10-10) INSTEAD OF
CUTOUTS WITH SOLID BLADES.
7. DISCONNECT CONNECTIONS MAY BE MADE WITH SOLID CONNECTION IN LIEU OF HOT LINE CLAMP AND STIRRUP.
3
11/17/15
LOOSIER
BURLISON
ADCOCK
2
4/21/15
LOOSIER
BURLISON
ADCOCK
1
3/29/11
HOFFMAN
BURLISON
ELKINS
0
10/6/10
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
DEC
DEM
DEP
DEF
RECLOSER ASSEMBLY,
VERTICAL CONSTRUCTION
X
08.05-15A
18"
12"
12"
TOP VIEW
8"
1
SIDE VIEW
BILL OF MATERIALS
MACRO UNIT
CU
ITEM
NO.
COMPATIBLE
UNIT
QTY
REQ'D
CATALOG
NUMBER
-
1
BKTEQ1824FGF
1
9220201401
13264
13308
152107
QTY
PER
CU
1
2
2
2
DESCRIPTION
BRACKET, FG, CUTOUT MTG BKT, 3 HOLE
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
WASHER, 2-1/4", SQUARE, FLAT, 13/16", HOLE, GALV.
BOLT, MACH, SQ. NUT, 5/8" X 12"
NOTES:
1. SEE DWG 08.05-15A FOR RECLOSER INSTALLATION DETAILS.
2. USE ONE CU PER RECLOSER INSTALLED.
3
2
1
0
10/11/10
REVISED
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
OIL CIRCUIT RECLOSER SINGLE-PHASE INSTALLATION
BYPASS CUTOUT BRACKET
R
DWG.
08.05-15B
5"
4"
11"
SEE NOTE 3
2
16"
60"
(SEE NOTE 2)
3
1
60"
4
72"
NOTES:
1. SEE DWG. 08.05-16B FOR BILL OF MATERIALS.
2. FOR ALL V4L RECLOSER INSTALLATIONS ON VERTICAL CONSTRUCTION, INCREASE THE
PHASE SPACING BETWEEN THE PRIMARY CONDUCTORS FROM 60" TO 64".
3. RISER SIZE SHOULD MATCH PRIMARY CONDUCTOR SIZE.
5
11/17/15
LOOSIER
BURLISON
ADCOCK
4
8/27/15
LOOSIER
BURLISON
ADCOCK
3
4/21/15
LOOSIER
BURLISON
ADCOCK
0
9/28/11
BURLISON
BURLISON
ELKINS
BY
CK'D
APPR.
REVISED
DEC
DEM
DEP
DEF
RECLOSER ASSEMBLY,
VERTICAL CONSTRUCTION, FEEDER
X
08.05-16A
BILL OF MATERIALS
CU
MACRO UNIT
ITEM
NO.
COMPATIBLE
UNIT
QTY REQ'D
1
SW156BYPF
1
2
3
2
KLC2H50ALF
2
4
6
3
KLC2H50AL90DF
2
4
6
4
RCRISER500ALF
2
4
6
-
CATALOG
NUMBER
QTY
010928
0012277
013128
013264
013308
013407
152107
260123
010928
012277
PER
CU
8
8
8
2
2
16
2
1
2
2
DESCRIPTION
BOLT, MACHINE, 1/2 IN, 2 IN, STAINLESS STEEL, 304, HEX HEAD
NUT, HEX, 1/2 IN, A304, STAINLESS STEEL, 304, ALLOY, COARSE THRD.
WASHER, ROUND, BELLEVILLE SPRING, FOR 1/2" BOLT
SPRING, DOUBLE COIL, STEEL, FOR, 5/8", BOLT, GALV.
WASHER, SQUARE, 2-1/4", FLAT, 13/16" HOLE, GALV.
WASHER, ROUND, FLAT, STAINLESS, STEEL, 304, ALLOY, FOR, 1/2"
BOLT, MACH, SQ, NUT, 5/8" X 12"
SWITCH, BYPASS, 3-SLD BLADE DISC, 15KV, LBK, HOOKS, 600A, LEFT
BOLT, MACHINE, 1/2 IN, 2 IN, STAINLESS STEEL, 304, HEX HEAD
NUT, HEX, 1/2 IN, A304, STAINLESS STEEL, 304, ALLOY, COARSE THRD.
013163
155326
10542504
010928
012277
013163
10542504
9220068102
202112
4
1
2
2
2
4
2
1
12
WASHER, FLAT, 1/2 IN, SILICON BRONZE, FLAT, ROUND
LUG, COMPRESSIN, 2H-795AL
WASHER, ROUND, RD, 1/2, SS, 1.375" OD
BOLT, MACHINE, 1/2 IN, 2 IN, STAINLESS STEEL, 304, HEX HEAD
NUT, HEX, 1/2 IN, A304, STAINLESS STEEL, 304, ALLOY, COARSE THRD.
WASHER, FLAT, 1/2 IN, SILICON BRONZE, FLAT, ROUND
WASHER, ROUND, 1/2, SS, 1.375" OD
LUG, 2-HOLE, TIN-PLATED, NEMA
CABLE, XLP UG AL 500
NOTES:
1. ISSUE RECLOSER SEPARATELY. RECLOSER WILL COME WITH ARRESTERS PREMOUNTED.
2. SEE DWG. 08.05-16A FOR DESIGN SPECIFICATIONS.
3
DEC
DEM
DEP
DEF
RECLOSER ASSEMBLY,
2
X
1
0
5/28/14
REVISED
LOOSIER
DANNA
ADCOCK
BY
CK'D
APPR.
VERTICAL CONSTRUCTION, FEEDER
08.05-16B
5"
6"
1
26"
2
54"
28"
3
6"
26"
4
SEE DWG. 08.05-15B
54"
ALL ENERGIZED
PARTS SHOULD
BE COVERED TO
GUARD AGAINST
DAMAGE CAUSED
BY ANIMALS
28"
6"
26"
72"
#2 SD BC
#2 SD BC
46"
FUSES
STORED WITH
BARRELS DOWN
ON 3" STAPLE
#6 SD BC
SIDE VIEW
FRONT VIEW
NOTES:
1. SEE DWG. 08.05-18B FOR PLAN VIEW, BILL OF MATERIALS AND NOTES.
3
DEC
2
11/17/15
LOOSIER
BURLISON
ADCOCK
1
4/21/15
LOOSIER
BURLISON
ADCOCK
0
12/6/13
SALAS
DANNA
ADCOCK
BY
CK'D
APPR.
REVISED
DEM
DEP
DEF
RECLOSER ASSEMBLY, VERTICAL CONSTRUCTION
SLACK SPAN TAP
X
08.05-18A
5
SOURCE
8
6
7
PLAN VIEW
LOAD
BILL OF MATERIALS
MACRO UNIT
-
CU
ITEM
NO.
1
2
3
4
5
6
7
8
QTY REQ'D
COMPATIBLE
UNIT
FUSE15CO100F
SW153COSBDF
KHLC40N6F
RCRISERN2CUF
SCLMP10AAACF
IDES25PF
DECLMP10AAACF
MIDSPANTAPF
1
2
3
1
1
1
1
1
2
4
6
2
2
2
2
2
ITEM
NUMBER
3
6
9
3
3
3
3
3
0000221112
9220210916
9220184790
9220218857
0000090306
080577
0000100708
0000115428
QTY
PER
CU
1
1
1
12FT.
1
1
1
1
DESCRIPTION
CUTOUT, LB, 15KV, 100A, 16KA,100KV BILL
CUTOUT, BLADE, BLADE,SLD,NONLOADBREAK,300A,15 KV
CLAMP, HOT LINE, ALUMINUM, SMALL
WIRE, COPPER, #2 SOLID, COPPER, 600V, SD COPPER
CLAMP, ANGLE, SUSPENSION,ANGLE,ALUMINUM,0.25-0.75"
INSULATOR, POLYMER, 25KV, DE, SI, RATED 15KV
CLAMP, DEADEND, DE,SO,6-4/0 ACSR,6-4/0 CU, 4-4/0 AL
LINK, CHAIN,TWISTED,90,25M,3-3/8",LONG
NOTES:
1. ISSUE RECLOSER SEPARATELY. RECLOSER WILL COME WITH ARRESTERS PRE-MOUNTED.
2. FOR ALL V4L RECLOSER INSTALLATIONS ON VERTICAL CONSTRUCTION, INCREASE THE PHASE SPACING
BETWEEN THE PRIMARY CONDUCTORS FROM 54" TO 64" AND INCREASE THE 28" DIMENSIONS TO 38".
3. SEE DWG 08.05-15B FOR BRACKET DETAILS AND BILL OF MATERIALS.
4. SEE DWG 03.18-03 FOR ALTERNATE SLACK SPAN CONSTRUCTION DETAILS.
5. SEE DWG. 08.05-18A FOR DESIGN SPECIFICATIONS.
6. FOR SINGLE-PHASE AND TWO-PHASE INSTALLATIONS, USE SPACING REQUIREMENTS FROM BOTTOM UNIT
CLOSEST TO NEUTRAL TOWARDS THE TOP OF THE POLE.
7. EQUIPMENT CASE GROUND TO NEUTRAL TO BE #2 SD BC.
8. IF RECLOSERS ARE USED IN MAIN LINE FEEDER (336 OR 795), USE 600 AMP RECLOSER BYPASS (SEE
DWG. 08.10-10 ) INSTEAD OF CUTOUTS WITH SOLID BLADES.
9.DISCONNECT CONNECTIONS MAY BE MADE WITH SOLID CONNECTION IN LIEU OF HOT LINE CLAMP AND STIRRUP.
3
DEC
DEM
DEP
DEF
RECLOSER ASSEMBLY, VERTICAL CONSTRUCTION
2
1
11/17/15
LOOSIER
BURLISON
ADCOCK
0
12/6/13
SALAS
DANNA
ADCOCK
BY
CK'D
APPR.
REVISED
SLACK SPAN TAP
X
08.05-18B
9"
15
LOAD
6"
SOURCE
5"
9"
5"
3
SOURCE
6"
9"
9
12"
1
2
BYPASS
CUTOUTS
7 10
12"
LOAD
20"
3"
15"
12"
30"
12"
30"
15"
3"
12"
8
3
11 16
SOURCE
LOAD
SOURCE
LOAD
10' ARM
7
LOAD
12"
10
SOURCE
4" MIN.
2
6
14
5
SLEET HOOD
SEE
NOTE 9
10-1/4"
4
#2 CU TANK
GROUND
17
12"
#2 CU FRAME GROUND
12
#6 CU POLE
GROUND
BYPASS FUSE
BARRELS
13
FRONT VIEW
SIDE VIEW
NOTES:
1. ALL SWITCHING SHALL BE DONE WITH TELESCOPIC STICK AS PER WORK STANDARDS. SOURCE AND LOAD
CUTOUTS ARE TO HAVE SOLID BLADES.
2. HANG FUSE BARRELS FROM BY-PASS CUTOUTS ON A DRIVE HOOK OR LAG SCREW NEAR THE NEUTRAL. HANG
BARRELS BY THE PULL RING SO WATER AND DEBRIS CANNOT COLLECT INSIDE BARREL.
3. ARRESTERS ARE TO BE CONNECTED TO BOTH SOURCE AND LOAD SIDE BUSHINGS AND INSTALLED ON THE
RECLOSER BRACKET DIRECTLY BEHIND THE RECLOSER BUSHING AS SHOWN.
4. SOURCE BUSHING IS LOCATED OVER THE MANUAL (YELLOW) HANDLE. ROTATE HEAD TO HAVE THE HANDLE
VISIBLE FROM NORMAL APPROACH (TYPICALLY ROAD SIDE).
5. BOND RECLOSERS TO THE RECLOSER MOUNTING BRACKET WITH #2 CU AND CONNECT TO SYSTEM NEUTRAL.
6. SINGLE-PHASE RECLOSERS HAVE DIFFERENT OPERATING CURVES: 2A2B, 2A2C, ETC. WHEN INSTALLING OR
REPLACING A RECLOSER, BE SURE THE UNIT HAS THE CORRECT OPERATING CURVES AS WELL AS THE CORRECT
AMPERE RATING TYPE.
7. SEE DWG. 08.05-114B FOR TABLES FOR RECLOSER TAP CONDUCTOR AND SWITCH SIZING AND BILL OF
MATERIALS.
8. SEE SYSTEM PROTECTION FOR BY-PASS SWITCH DETAILS.
9. SEE DWG. 08.05-02 FOR RECLOSER HEIGHT MEASUREMENT.
3
2
1
12/16/15
LOOSIER
BURLISON
ADCOCK
0
11/17/15
BRUINS
BURLISON
ADCOCK
BY
CK'D
APPR.
REVISED
OIL CIRCUIT RECLOSERS, THREE-PHASE INSTALLATION,
DEC
DEM
DEP
DEF
HORIZONTAL CONSTRUCTION
SINGLE-PHASE UNITS
X
X
X
X
08.05-114A
BILL OF MATERIALS
BUBBLE
NUMBER
COMPATIBLE
UNIT
CU
QTY
1
ARMSDE120HFF
1
2
2
2
3
3
4
RCRISERN2CUF
RCRISER10ALF
RCRISER40ALF
FUSE15CO100F
SW153COSBDF
RCL(VARIES)
6
6
6
3
6
3
5
BKTTFMRSMALF
1
WGEQBUSHSNAPF
IHPTT35F
6
6
3
ISSTUDBOLT5812F
3
8
ARMS120FF
1
6
7
9
BKTCOLASTLXARMF
3
10
10
-
1
1
11
BKTCOLASTLXARMF
6
12
-
1
GOWE2F
1
GRODFRF
1
GAR1F
3
AREQOH10F
IDES25PF
DECLMP(VARIES)
-
6
6
6
6
13
14
15
16
ITEM
NUMBER
9220272389
152122
13346
13265
9220218857
54008800
202111
202112
9220210916
12912507
152122
13346
13265
152104
470114
9220284709
80217
72367
13264
9220201451
152107
13346
13264
70101
11213
9220284739
9220284740
70101
11213
14114
9220162221
15280
153111
160182
162205
160123
9220192319
60136
9220192319
220202
80577
-
ITEM
QTY/
CU
1
2
2
2
12
12
12
1
1
3
1
2
2
2
6
1
1
1
1
1
1
2
2
2
1
2
1
1
1
2
1
40
40
1
2
2
1
1
1
1
1
1
1
1
DESCRIPTION
CROSSARM, DEADEND, HD, FIBERGLASS
BOLT, HEX, 3/4 IN, 10"X12 STEEL, A307
WASHER SQUARE, RB, CRV, 3"X3"
WASHER, LOCK, 3/4 IN DBL COIL
CONDUCTOR, COPPER, WP #2 AWG
CONDUCTOR, AAAC, 1/0, AAAC, 7-STR, 6201-T81 ALUMINUM ALLOY
CABLE, XLP UG AL 4/0
CUTOUT, NON LOADBREAK, 15KV,100A
CUTOUT, BLADE, BLADE,SLD,NONLOADBREAK,300A,15 KV
RECLOSER TYPE L (VARIABLE AMP AND CURVE)
BRACKET, MOUNTING, MTG,RACK,TF,SM THREE POS, 5-50KVA
BOLT, SQUAREHEAD, 3/4 IN, 12 IN, S, A307, GLV, 10, UNC
WASHER SQUARE, RB, CRV, 3"X3"
WASHER, LOCK, 3/4 IN DBL COIL
BOLT, MACHINE, 5/8 IN, 2 IN, ASTM A307, A, GALVANIZED, SQ
GUARD, ANIMAL, 9 INCH HT
GUARD, ANIMAL, 5 1/2 INCH HT
INSULATOR, POST, LINE, 35KV ROUND BASE TIE TOP
STUD, LINE POST, LP 5/8 INCH X 12 INCH
WASHER, LOCK, 5/8 IN, STEEL, GLV, LK,5/8,COIL,DBL,GLV
CROSSARM, TANGENT, 10 FT, FIBERGLASS, BRACELESS, TANGENT
BOLT, MACHINE, 5/8 IN, 11 INX 12 IN, STEEL
WASHER SQUARE, RB, CRV, 3"X3"
WASHER, LOCK, 5/8 IN, STEEL, GLV, LK,5/8,COIL,DBL,GLV
BRACKET, MOUNTING, 8 7/8 IN X 2 1/2 IN IN, GALVANIZED STEEL
BOLT, CARRIAGE, 1/2 IN, 6 IN, STEEL, GLV
TIE, COMPOSITE FOR #2 TO #2/0
TIE, COMPOSITE FOR #2/0 TO #4/0
BRACKET, MOUNTING, 8 7/8 IN X 2 1/2 IN IN, GALVANIZED STEEL
BOLT, CARRIAGE, 1/2 IN, 6 IN, STEEL, GLV
SCREW, LAG, 1/4 IN X 2 IN, STEEL, GLV, LAG,HX,1/4-INCH O.D.
CONDUCTOR, COPPER, #2 SOLID, SOFT DRAWN, BARE
STAPLE, DIAMOND POINT, GALV STL 2X5/8X3/16
CONNECTOR, COMPRESSION, COMP, AL
CONNECTOR, GROUND, TF,GND,EYEBOLT
CONNECTOR, VISE TYPE 2 CU
CLAMP, GROUND, GRD,BRN,5/8 CAST BRONZE GROUND ROD CLAMP
ROD, GROUND, 5/8 X 60 IN, COPPER CLAD, THREADLESS 5/8" X 5'
COUPLING, ROD, 5/8 IN, COPPER PLATED STEEL, ROD,GRD,5/8
ROD, GROUND, 5/8 X 60 IN, COPPER CLAD, THREADLESS 5/8" X 5'
ARRESTER, METAL OXIDE, 10KV,METOX DIST CLASS, METAL OXIDE
INSULATOR, DEADEND, POLYMER,28KV,DEADEND,SILICONE
DEADEND CLAMP (VARIES WITH WIRE SIZE)
BLADES COME WITH SW253COSBDC
NOTES:
1. SEE DWG. 08.05-114A FOR DESIGN SPECIFICATIONS AND NOTES.
3
2
1
12/16/15
LOOSIER
BURLISON
ADCOCK
0
11/17/15
BURLISON
EANES
ADCOCK
BY
CK'D
APPR.
REVISED
OIL CIRCUIT RECLOSERS, THREE-PHASE INSTALLATION,
HORIZONTAL CONSTRUCTION
SINGLE-PHASE UNITS
DEC
DEM
DEP
DEF
X
08.05-114B
LOAD
SOURCE
6"
6
7
10
48"
48"
5
4
11
48"
PT
35"
9
8
76"
L1
TERMINAL L1
L2
#6 SD BC
37"
#2 SD BC
1
BLACK
GREEN - GROUND
3
BLACK
4"
SECONDARY
ARRESTER
4"
12
SECONDARY ARRESTER CONNECTION
#6 SD BC
4 HOLE
SPADE ON
RECLOSER
2
38"
LOCKWASHER
1/2" SS
BOLT
NUT
#6 BC
BOLT ON TAMPER
GUARD FOR
CONTROL CABLE
PLUG
ROUND
WASHER
48" MIN.
ROUND
BOLT
#6 BC
DETAIL "B"
FRONT VIEW
SIDE VIEW
NOTES:
1.
2.
3.
4.
5.
6.
7.
8.
SWITCHES TO BE ON ROAD SIDE.
PT TO BE LOCATED ON SOURCE SIDE. RELOCATE ON RECLOSER FRAME IF NECESSARY.
SIX ARRESTERS REQUIRED: 3 ON EACH SIDE. CONNECT TO TERMINALS OF RECLOSER WITH CONNECTOR UNDER WILDLIFE PROTECTORS.
A 45' CLASS 4 POLE IS THE MINIMUM TO BE USED FOR THIS INSTALLATION.
TOTAL WEIGHT OF THE RECLOSER AND FRAME IS 850 LBS.
ISSUE TAPS TO SWITCHES SEPARATELY (WIRE, CONNECTORS, AND LUGS). BOLTS WILL BE ON SWITCH.
ALL BOLTS ON PRIMARY CONNECTIONS ARE TO BE TORQUED TO 40 FT-LBS. DO NOT EXCEED!
SEE DWG. 08.06-08B FOR BILL OF MATERIALS.
4
12/19/14
BURLISON
GUINN
ADCOCK
3
5/28/14
GUINN
GUINN
ADCOCK
2
11/8/12
HOFFMAN
DANNA
ADCOCK
0
10/12/10
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
DEC
DEM
DEP
DEF
RECLOSER AND FRAME, THREE-PHASE, ABB
WITH VERTICAL BYPASS SWITCH
X
08.06-08A
BILL OF MATERIALS
MACRO UNIT
-
CU
ITEM
NO.
COMPATIBLE
UNIT
QTY
REQ'D
CATALOG
NUMBER
9220090147
152107
013308
013264
013128
013407
010928
012277
9220069244
9220087550
9220100429
013264
013308
152107
260123
9220087868
9220091018
9220068094
220202
010928
012277
013163
155326
10542504
9220068102
202112
323422
434122
434142
220139
9220102212
9220102213
9220102214
1
RCOVR630E15V1F
1
2
3
RCCNTLPCDABBF
RCOVRCAB40F
1
1
4
SW156BYPF
3
5
6
7
8
BKTFBGPIN15138F
IPIN25PF
TTIEF500COVALPF
AREQOH10F
4
4
4
6
9
KLC2H50ALF
6
10
11
KLC2H50AL90DF
RCRISER500ALF
6
6
12
CRIS1UGPVC225CF
2
13
14
15
16
AREQSC120F
WGRCTERMGSF
WGRCLSHPF
WGRCPTTRF
1
3
3
3
COMPATIBLE
UNIT
QTY
REQ'D
CATALOG
NUMBER
RCOVR630E27V1F
RCCNTLPCDABBNSF
RCCNTLPCDRFF
RCPCDLCMF
-
1
1
1
1
1
-
9220087177
9220085219
9220087633
9220085231
9220087552
9220102215
9220087542
9220100256
9220085226
9220102547
9220127574
9220127570
9220127579
9220127587
9220127588
9220127589
9220127564
9220085231
9220087168
QTY
PER
CU
1
16
17
15
75
72
36
36
4
1
1
2
2
2
1
1
1
1
1
2
2
4
1
2
1
12
1
0.2
3
1
1
1
1
DESCRIPTION
RECLOSER TYPE OVR 630 AMP ELEC. 15KV VRT MNTG W/1PT
BOLT, MACHINE, SQ, NUT, 5/8" X 12"
WASHER, SQUARE, 2-1/4", FLAT, 13/16" HOLE, GALV.
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
WASHER, ROUND, BELLEVILLE SPRING, FOR 1/2" BOLT
WASHER, ROUND, FLAT, STAINLESS STEEL, 304 ALLOY
BOLT, MACHINE, STAINLESS STEEL, HEX HEAD, 1/2" X 2"
NUT, STAINLESS STEEL, HEX, 304 ALLOY, COARSE THREAD
WIRE, TIE, #4 SD BC, SLD
RECLOSER CONTROL PCD 2000 FOR ABB RECL
RECLOSER CONTROL CABLE FOR ABB VR3 AND OVR, 40FT
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
WASHER, SQUARE, 2-1/4", FLAT, 13/16" HOLE, GALV.
BOLT, MACHINE, SQ, NUT, 5/8" X 12"
SWITCH, BYPASS, 3-SLD BLADE DISCONNECT, 15KV, LBK
BRACKET, FIBERGLASS STAND-OFF, 1-3/8" THREAD
INSULATOR, 25 KV POLYMER, 1-3/8" THREAD
PLASTIC TIE WRAP FOR 2-7/8" F-NECK INSULATOR
ARRESTER, LIGHTNING, 10KV HD MOV W/SILICONE RUBBER POLY
BOLT, MACHINE, STAINLESS STEEL, HEX HEAD, 1/2" X 2"
NUT, STAINLESS STEEL, HEX, 304 ALLOY, COARSE THREAD
WASHER, FLAT, ROUND, SILICON, BRONZE, FOR 1/2" BOLT
LUG, COMP 2H 500 AL
WASHER, ROUND, RD, 1/2, SS, 1.375" OD
LUG, 2-HOLE, TIN-PLATED, NEMA, 90 DEGREE
CABLE, XLP UG AL 500
GUARD, PVC, CABLE, 2-1/4" X 10'
BANDING, STAINLESS STEEL, 316, 3/4" WIDE, .030 TH
BANDING, BUCKLE, SS, 3/4", FOR BANDING
ARRESTER, LIGHTNING, SEC 120-240 3 WIRE
GUARD, ANIMAL, TERMINAL GUARD, STRAIGHT
GUARD, ANIMAL, L-SHAPED, GUARD
GUARD, ANIMAL, PT OR VOLTAGE TRANSFORMER
ADDITIONAL PARTS FOR REPLACEMENT
MACRO UNIT
-
CU
ITEM
NO.
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
QTY
PER
CU
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
DESCRIPTION
RECLOSER, ABB OVR-630 AMP, 12KA, 27KV-HV EDGEMOUNT COASTAL
RECLOSER, PCD,CONTROL,LV,MODULE,WITHOUT,SINGLE-PHASE,TRI
RECLOSER, CONTROL, PCD 2000 COOPER RETROFIT
TRANSFORMER, POTENTIAL, 15KV,7200V
MODULE, LOOP CONTROL, RECLOSER, ABB, FOR PCD CONTROL.
CABLE LOCKING SLEEVE - ABB RECL. CTRL CABLE CONNECTOR
BATTERY, RECLOSER, PCD CNTRL, 48VDC (SET OF 4-12VDC)
CABLE-PT, ABB RECLOSER, 8 FOOT, W/2-5-PRONG CONNECTORS
ABB PCD SINGLE-PHASE TRIP CARD
COM5 MODULE/CARD FOR ABB PCD CONTROL (SLOT-E)
ABB PCD UPS CARD TYPE 3, 48VDC (SLOT-A)
ABB PCD UPS CARD TYPE 2, 48VDC (SLOT-A)
ABB PCD DIO-2B I/O CARD (SLOT-B)
ABB PCD DIO-1 I/O CARD (SLOT-C)
ABB PCE CPU-2 CARD (SLOT-D)
ABB PCD COM-2A CARD (SLOT-E)
ABB PCD PT/CT 600:1 CARD (SLOT-F)
EXTERNAL PT FOR ABB OVR RECL, 13.8V, 110BIL, VOG-11, 60:1
COASTAL EXT. PT- ABB OVR RECL, 13.8 KV, 125 KV BIL, W/60:1 RATIO
NOTES:
1.
2.
3.
4.
5.
6.
GROUND RESISTANCE TO BE 15 OHMS OR LESS.
A 45' CLASS 4 POLE IS THE MINIMUM TO BE USED FOR THIS INSTALLATION.
TOTAL WEIGHT OF RECLOSER ASSEMBLY IS 850 LBS.
ISSUE TAPS TO SWITCHES SEPARATELY (WIRE, CONNECTORS, AND LUGS). BOLTS WILL BE ON SWITCH.
ALL BOLTS ON PRIMARY CONNECTIONS ARE TO BE TORQUED TO 40 FT-LBS: DO NOT EXCEED!
SEE DWG. 08.06-08A DESIGN SPECIFICATIONS.
4
12/19/14
BURLISON
GUINN
ADCOCK
3
11/14/12
HOFFMAN
DANNA
ADCOCK
2
3/28/12
HOFFMAN
BURLISON
ELKINS
0
11/9/10
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
DEC
DEM
DEP
DEF
RECLOSER ASSEMBLY, THREE-PHASE, ABB
WITH VERTICAL BYPASS SWITCH
X
08.06-08B
5"
36"
36"
EXTRA CAUTION SHOULD
BE TAKEN WHEN BOLTING
CONNECTIONS OR
TRAINING LEADS TO
BUSHINGS. SEE NOTE 4
ON DWG. 08.06-08B.
LOAD
SOURCE
36"
6"
48"
48"
48"
SEE DETAIL "A"
SEE DETAIL "B"
35"
76"
#6 SD BC
37"
#2 SD BC
CN 153109
CN 9220102212
4"
4"
USE WILDLIFE GUARDS
CN 9220102213
#6 SD BC
38"
BOLT ON TAMPER
GUARD FOR CONTROL
CABLE PLUG
48" MIN.
DETAIL "A"
DETAIL "B"
CN 9220102214
FRONT VIEW
NOTES:
SIDE VIEW
1. SEE DWG. 08.06-08B FOR BILL OF MATERIALS AND REPLACEMENT PARTS FOR RECLOSER INSTALLATION.
2. A 55' CLASS 3 POLE IS THE MINIMUM TO BE USED FOR THIS INSTALLATION.
3. SEE DWG. 08.06-08A FOR MORE DETAILS ON RECLOSER INSTALLATION, INCLUDING SECONDARY AND PRIMARY
ARRESTER CONNECTIONS.
3
2
DEC
12/19/14
BURLISON
GUINN
ADCOCK
1
11/8/12
HOFFMAN
DANNA
ADCOCK
0
10/12/10
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
DEM
DEP
ABB RECLOSER ON VERTICAL DOUBLE CIRCUIT W/
VERTICAL BYPASS SWITCH
DEF
X
08.06-10
5"
USE WILDLIFE GUARDS
SOURCE
6"
LOAD
3
4
5
24"
48"
DETAIL "A"
9
48"
2
(2) 9220252997
(4) 9220102213
24"
8
10
16
DETAIL "B"
VIPER ST JUNCTION
BOX PANEL; SEE NOTE 4
ON 08.06-11C
56"
7
SOURCE
SEE DETAIL "A"
56"
17
SEE
DETAIL "C"
LOAD
108"
L1
6
#2 CU
TERMINAL L1
1
L2
BLACK
12
SEE DETAIL "B"
GREEN - GROUND
BLACK
NEUTRAL
SECONDARY
ARRESTER
14 15
11
SECONDARY ARRESTER CONNECTION
IN CONTROL BOX
#6 SD BC
4 HOLE
SPADE ON
RECLOSER
LOCKWASHER
1/2" SS
BOLT
13
38"
NUT
#6 WP
ROUND
WASHER
#6 WP
48" MIN.
BOLT ON TAMPER
GUARD FOR
CONTROL CABLE
PLUG
ROUND
BOLT
DETAIL "C"
FRONT VIEW
SIDE VIEW
NOTES:
1. SEE DWG. 08.06-11C FOR BILL OF MATERIALS AND NOTES.
2. BRACKET IS REVERSIBLE AND CAN BE INSTALLED ON EITHER SIDE OF POLE TO SUIT FIELD CONDITIONS.
3. IN COASTAL AREAS, USE DWG. 08.06-12A FOR 25KV CONSTRUCTION.
6
8/10/15
LOOSIER
BURLISON
ADCOCK
5
7/1/15
LOOSIER
BURLISON
ADCOCK
4
2/17/14
McCONNELL
DANNA
ADCOCK
0
10/12/12
HOFFMAN
BURLISON
ADCOCK
BY
CK'D
APPR.
REVISED
DEC
DEM
DEP
DEF
RECLOSER AND FRAME, THREE-PHASE, VIPER ST,
WITH VERTICAL BYPASS SWITCH
X
08.06-11A
16
59.62"
SOURCE SIDE
LOAD SIDE
6
17
19
55.76"
44.75"
6
16.5"
27.66"
47.7"
ATTACH GROUND
STIRRUP TO FRAME
1
PT JUNCTION
BOX
29.74"
LOWER SUPPORTS
SHIPPED UNATTACHED
RIGHT VIEW
BACK VIEW
(ANIMAL GUARD NOT SHOWN FOR CLARITY)
#6 CU WP
SHIPPED WITH UNIT
ALUMINUM POLE
MOUNTING FRAME
MODULE CABLE
ACCESS IN THE
J-BOX
INTERNAL CURRENT
TRANSFORMER
#6 CU WP
SEE DETAIL C
ON DWG. 08.06-11A
JUNCTION BOX
RECLOSER CONTROL
CABLE AND HARDWARE
2.13"
20"
1.27"
3.02"
SPACING AVAILABLE
FOR 3 ADDITIONAL
PTS IF NECESSARY
52.06"
LEFT VIEW
NOTES:
(ANIMAL GUARD NOT SHOWN FOR CLARITY)
1. SEE DWG. 08.06-11A FOR DESIGN SPECIFICATIONS.
2. SEE DWG. 08.06-11C FOR BILL OF MATERIALS AND NOTES.
3. BRACKET IS REVERSIBLE. DEPENDING ON HOW UNIT IS INSTALLED IN FIELD, DIAGRAMS
ABOVE MAY BE REVERSED.
3
7/1/15
LOOSIER
BURLISON
ADCOCK
2
7/21/14
LOOSIER
DANNA
ADCOCK
1
2/17/14
McCONNELL
DANNA
ADCOCK
0
6/7/13
McCONNELL
DANNA
ADCOCK
BY
CK'D
APPR.
REVISED
DEC
DEM
DEP
DEF
RECLOSER AND FRAME, THREE-PHASE, VIPER ST,
WITH VERTICAL BYPASS SWITCH
X
08.06-11B
BILL OF MATERIALS
MACRO UNIT
CU
ITEM
NO.
1
COMPATIBLE
UNIT
RCVST800E27V1F
QTY
REQ'D
ITEM
NUMBER
1
9220244274
152107
013308
013264
013128
013407
010928
012277
9220069244
QTY
PER
CU
1
16
17
15
75
72
36
36
4
8
8
8
2
2
16
2
1
2
2
2
1
1
1
1
2
2
4
1
2
2
2
SW156BYPF
3
3
BKTFBGPIN15138F
4
4
5
6
IPIN25PF
TTIEF500COVALPF
AREQOH10F
4
4
-
7
KLC2H50ALF
5
8
KLC2H50AL90DF
7
9
KLC2H79ALF
6
10
RCRISER500ALF
6
11
CRIS1UGPVC225WF
2
12
13
RCVIPCAB40F
RCCNTL651GWF
1
1
010928
0012277
013128
013264
013308
013407
152107
260123
013264
013346
152107
9220087868
9220091018
9220068094
220202
010928
012277
013163
155326
10542504
010928
012277
013163
10542504
9220068102
010928
012277
013163
10542504
155331
202112
014111
323422
9220244739
9220244823
14
-
-
9220267667
1
15
16
17
18
19
WGRCSLDSVF
WGRCLSHPF
WGRCPTTRF
-
2
4
3
-
PRECHARGE
9220252997
9220102213
9220102214
9220085231
1
1
1
3
-
2
4
2
1
2
2
4
2
1
12
15
1
1
1
DESCRIPTION
RECLOSER TYPE VST 800 AMP ELEC. 27KV VRT MNTG
BOLT, MACHINE, SQ, NUT, 5/8" X 12"
WASHER, SQUARE, 2-1/4", FLAT, 13/16" HOLE, GALV.
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
WASHER, ROUND, BELLEVILLE SPRING, FOR 1/2" BOLT
WASHER, ROUND, FLAT, STAINLESS STEEL, 304 ALLOY
BOLT, MACHINE, STAINLESS STEEL, HEX HEAD, 1/2" X 2"
NUT, STAINLESS STEEL, HEX, 304 ALLOY, COARSE THREAD
WIRE, TIE, #4 SD BC, SLD
BOLT, MACHINE, 1/2 IN, 2 IN, STAINLESS STEEL, 304, HEX HEAD
NUT, HEX, 1/2 IN, A304, STAINLESS STEEL, HEX
WASHER, ROUND, BELLEVILLE SPRING, FOR 1/2" BOLT
WASHER, LOCK, 5/8 IN, STEEL, GLV, SPRING, DOUBLE COIL, F
WASHER, SQUARE, 2-1/4", FLAT, 13/16" HOLE, GALV.
WASHER, ROUND, FLAT, STAINLESS, STEEL, 304, ALLOY, FOR, 1/2"
BOLT, MACH, SQ, NUT, 5/8" X 12"
SWITCH, BYPASS, 3-SLD BLADE DISC, 15KV, LBK, HOOKS, 600A, LEFT
WASHER, LOCK, 5/8 IN, STEEL, GLV, SPRING, DOUBLE COIL, F
WASHER,3", SQUARE, CURVED, 13/16", HOLE
BOLT, MACH, SQ, NUT, 5/8" X 12"
BRACKET, FIBERGLASS STAND-OFF, 1-3/8" THREAD
INSULATOR, 25 KV POLYMER, 1-3/8" THREAD
PLASTIC TIE WRAP FOR 2-7/8" F-NECK INSULATOR
ARRESTER (INCLUDED FROM MANUFACTURER)
BOLT, MACHINE, STAINLESS STEEL, HEX HEAD, 1/2" X 2"
NUT, STAINLESS STEEL, HEX, 304 ALLOY, COARSE THREAD
WASHER, FLAT, ROUND, SILICON, BRONZE, FOR 1/2" BOLT
LUG, COMP 2H 500 AL
WASHER, ROUND, RD, 1/2, SS, 1.375" OD
BOLT, MACHINE, 1/2 IN, 2 IN, STAINLESS STEEL, 304, HEX HEAD
NUT, HEX, 1/2 IN, A304, STAINLESS STEEL, HEX
WASHER, FLAT, ROUND, SILICON, BRONZE, FOR, 1/2", BOLT
WASHER, ROUND, 1/2, SS, 1.375" OD
LUG, 2-HOLE, TIN-PLATED, NEMA
BOLT, MACHINE, 1/2 IN, 2 IN, STAINLESS STEEL, 304, HEX HEAD
NUT, HEX, 1/2 IN, A304, STAINLESS STEEL, HEX
WASHER, FLAT, ROUND, SILICON, BRONZE, FOR, 1/2", BOLT
WASHER, ROUND, 1/2, SS, 1.375" OD
LUG, COMPRESSION, 2H-795AL
CABLE, XLP UG AL 500
SCREW, LAG, HX, 1/4" X 2", STEEL, GALV.
GUARD, PVC, CABLE, 2-1/4" X 10"
VIPER ST CONTROL CABLE
SEL 651 CONTROL
CONTROL CABLE, 40' ARMORED 8 PIN FOR PT
(INCLUDED FROM MANUFACTURER)
1" CONDUIT, FLEX, AND FITTING
GUARD, ANIMAL, SOLID COVER, STRAIGHT, VERTICAL
GUARD, ANIMAL, L-SHAPED
GUARD, ANIMAL, PT OR VOLTAGE TRANSFORMER
TRANF, POTENTIAL (INCLUDED FROM MANUFACTURER)
NOTES:
1. SEE DWG. 08.06-11A FOR DESIGN SPECIFICATIONS.
2. GROUND RESISTANCE TO BE 15 OHMS OR LESS.
3. CONNECT ENDS OF POWER AND CONTROL CABLES WITH PROTECTIVE ARMORED FLEX TO CONTROL.
4. WHEN INSTALLING UNIT, OPEN JUNCTION BOX PANEL BY REMOVING SCREWS, RECORD 3 PT CORRECTION FACTORS LISTED AND PLACE
ON INSIDE DOOR OF CONTROL. CLOSE JUNCTION BOX PANEL.
5. A 45' CLASS 4 POLE IS THE MINIMUM TO BE USED FOR THIS INSTALLATION. IF JOINT USE ON POLE, CLEARANCES MAY REQUIRE 50' POLE.
6. ISSUE TAPS TO SWITCHES SEPARATELY (WIRE, CONNECTORS, AND LUGS). BOLTS WILL BE ON SWITCH.
7. ALL BOLTS ON PRIMARY CONNECTIONS ARE TO BE TORQUED TO 40 FT-LBS: DO NOT EXCEED!
8. PT'S TO BE LOCATED ON SOURCE SIDE. POWER SOURCE FOR PT'S FROM UNIT 1.
9. SIX ARRESTERS REQUIRED: 3 ON EACH SIDE. CONNECT TO TERMINALS OF RECLOSER AS SHOWN ON DETAIL C ON DWG. 08.06-11A.
10. USE #6 CU WP FOR ARRESTER SECONDARY CONNECTIONS.
11. TOTAL WEIGHT OF THE RECLOSER AND FRAME IS 750 LBS DOES NOT INCLUDE PT'S OR LA'S.
12. NEUTRAL MAY BE DOUBLE DEADENDED OR STRAIGHT THROUGH ON SPOOL AS NEEDED.
13. ARRESTORS, PT'S and 8 PIN PT CONTROL CABLE COME WITH RECLOSER FROM MANUFACTURER.
4
7/1/15
LOOSIER
BURLISON
ADCOCK
3
10/17/14
LOOSIER
DANNA
ADCOCK
2
5/2/14
LOOSIER
DANNA
ADCOCK
0
6/7/13
DANNA
ADCOCK
CK'D
APPR.
REVISED
BY
DEC
DEM
DEP
DEF
RECLOSER ASSEMBLY, THREE-PHASE, VIPER ST
WITH VERTICAL BYPASS SWITCH
X
08.06-11C
5"
USE WILDLIFE GUARDS
SOURCE
6"
LOAD
3
4
5
24"
48"
DETAIL "A"
9
48"
2
(2) 9220252997
(4) 9220102213
24"
8
10
16
DETAIL "B"
VIPER ST JUNCTION
BOX PANEL; SEE NOTE 4
ON 08.06-12C
56"
7
SOURCE
SEE DETAIL "A"
56"
17
SEE
DETAIL "C"
LOAD
108"
L1
6
#2 CU
TERMINAL L1
1
L2
BLACK
12
SEE DETAIL "B"
GREEN - GROUND
BLACK
NEUTRAL
SECONDARY
ARRESTER
14 15
11
SECONDARY ARRESTER CONNECTION
IN CONTROL BOX
#6 SD BC
4 HOLE
SPADE ON
RECLOSER
LOCKWASHER
1/2" SS
BOLT
13
38"
NUT
#6 WP
ROUND
WASHER
#6 WP
48" MIN.
BOLT ON TAMPER
GUARD FOR
CONTROL CABLE
PLUG
ROUND
BOLT
DETAIL "C"
FRONT VIEW
SIDE VIEW
NOTES:
1. SEE DWG. 08.06-12C FOR BILL OF MATERIALS AND NOTES.
2. BRACKET IS NOT REVERSIBLE. WILL NEED TO MOUNT UNIT ROAD SIDE OR FIELD SIDE DEPENDING ON
DIRECTION OF SOURCE.
3
8/10/15
LOOSIER
BURLISON
ADCOCK
2
7/17/15
LOOSIER
BURLISON
ADCOCK
1
11/6/13
SALAS
DANNA
ADCOCK
0
10/7/13
SALAS
DANNA
ADCOCK
BY
CK'D
APPR.
REVISED
RECLOSER AND FRAME, THREE-PHASE, VIPER ST,
WITH VERTICAL BYPASS SWITCH
- 25KV CONSTRUCTION -
DEC
DEM
DEP
DEF
X
08.06-12A
16
59.62"
SOURCE SIDE
LOAD SIDE
6
17
19
55.76"
44.75"
6
16.5"
27.66"
47.7"
ATTACH GROUND
STIRRUP TO FRAME
1
PT JUNCTION
BOX
29.74"
LOWER SUPPORTS
SHIPPED UNATTACHED
RIGHT VIEW
BACK VIEW
(ANIMAL GUARD NOT SHOWN FOR CLARITY)
#6 CU WP
SHIPPED WITH UNIT
ALUMINUM POLE
MOUNTING FRAME
MODULE CABLE
ACCESS IN THE
J-BOX
INTERNAL CURRENT
TRANSFORMER
#6 CU WP
SEE DETAIL C
ON DWG. 08.06-12A
JUNCTION BOX
RECLOSER CONTROL
CABLE AND HARDWARE
2.13"
20"
1.27"
3.02"
SPACING AVAILABLE
FOR 3 ADDITIONAL
PTS IF NECESSARY
52.06"
LEFT VIEW
(ANIMAL GUARD NOT SHOWN FOR CLARITY)
NOTES:
1. SEE DWG. 08.06-12A FOR DESIGN SPECIFICATIONS.
2. SEE DWG. 08.06-12C FOR BILL OF MATERIALS AND NOTES.
3
2
7/17/15
LOOSIER
1
7/21/14
LOOSIER
DANNA
ADCOCK
0
10/7/13
SALAS
DANNA
ADCOCK
BY
CK'D
APPR.
REVISED
BURLISON
ADCOCK
RECLOSER AND FRAME, THREE-PHASE, VIPER ST,
WITH VERTICAL BYPASS SWITCH
- 25KV CONSTRUCTION -
DEC
DEM
DEP
DEF
X
08.06-12B
BILL OF MATERIALS
MACRO UNIT
CU
ITEM
NO.
COMPATIBLE
UNIT
QTY
REQ'D
ITEM
NUMBER
9220244274
152107
013308
013264
1
RCVST800E27V1F
1
2
SW256BYPF
3
3
BKTFBGPIN15138F
4
4
5
6
IPIN25PF
TTIEF500COVALPF
AREQOH18F
4
4
6
7
KLC2H50ALF
5
8
KLC2H50AL90DF
7
9
KLC2H79ALF
6
10
RCRISER500ALF
6
11
CRIS1UGPVC225CF
2
12
13
14
15
16
17
18
19
RCVIPCAB40F
RCCNTL651GWF
WGRCSLDSVF
WGRCLSHPF
WGRCPTTRF
-
1
1
40
2
4
3
-
-
QTY
PER
CU
1
16
17
15
013264
013346
152107
9220087868
9220091018
9220068094
220207
010928
75
72
36
36
4
8
8
8
2
2
16
2
1
2
2
2
1
1
1
1
2
012277
013163
155326
10542504
010928
012277
013163
10542504
9220068102
010928
012277
013163
10542504
155331
202112
323422
434122
434142
9220244739
9220244823
192324
PRECHARGE
9220252997
9220102213
9220102214
0020800983
2
4
1
2
2
2
4
2
1
2
2
4
2
1
12
1
0.2
3
1
1
1
1
1
1
3
013128
013407
010928
012277
9220069244
010928
0012277
013128
013264
013308
013407
152107
260552
DESCRIPTION
RECLOSER TYPE VST 800 AMP ELEC. 27KV VRT MNTG
BOLT, MACHINE, SQ, NUT, 5/8" X 12"
WASHER, SQUARE, 2-1/4", FLAT, 13/16" HOLE, GALV.
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
WASHER, ROUND, BELLEVILLE SPRING, FOR 1/2" BOLT
WASHER, ROUND, FLAT, STAINLESS STEEL, 304 ALLOY
BOLT, MACHINE, STAINLESS STEEL, HEX HEAD, 1/2" X 2"
NUT, STAINLESS STEEL, HEX, 304 ALLOY, COARSE THREAD
WIRE, TIE, #4 SD BC, SLD
BOLT, MACHINE, 1/2 IN, 2 IN, STAINLESS STEEL, 304, HEX HEAD
NUT, HEX, 1/2 IN, A304, STAINLESS STEEL, HEX
WASHER, ROUND, BELLEVILLE SPRING, FOR 1/2" BOLT
WASHER, LOCK, 5/8 IN, STEEL, GLV, SPRING, DOUBLE COIL, F
WASHER, SQUARE, 2-1/4", FLAT, 13/16" HOLE, GALV.
WASHER, ROUND, FLAT, STAINLESS, STEEL, 304, ALLOY, FOR, 1/2"
BOLT, MACH, SQ, NUT, 5/8" X 12"
SWITCH, BYPASS, 3-SLD BLADE DISC, 25KV, LBK HOOKS, 600A, LEFT OPENING
WASHER, LOCK, 5/8 IN, STEEL, GLV, SPRING, DOUBLE COIL, F
WASHER,3", SQUARE, CURVED, 13/16", HOLE
BOLT, MACH, SQ, NUT, 5/8" X 12"
BRACKET, FIBERGLASS STAND-OFF, 1-3/8" THREAD
INSULATOR, 25 KV POLYMER, 1-3/8" THREAD
PLASTIC TIE WRAP FOR 2-7/8" F-NECK INSULATOR
ARRESTER, LIGHTNING, 18KV HD MOV W/SILICONE RUBBER POLY
BOLT, MACHINE, STAINLESS STEEL, HEX HEAD, 1/2" X 2"
NUT, STAINLESS STEEL, HEX, 304 ALLOY, COARSE THREAD
WASHER, FLAT, ROUND, SILICON, BRONZE, FOR 1/2" BOLT
LUG, COMP 2H 500 AL
WASHER, ROUND, RD, 1/2, SS, 1.375" OD
BOLT, MACHINE, 1/2 IN, 2 IN, STAINLESS STEEL, 304, HEX HEAD
NUT, HEX, 1/2 IN, A304, STAINLESS STEEL, HEX
WASHER, FLAT, ROUND, SILICON, BRONZE, FOR, 1/2", BOLT
WASHER, ROUND, 1/2, SS, 1.375" OD
LUG, 2-HOLE, TIN-PLATED, NEMA
BOLT, MACHINE, 1/2 IN, 2 IN, STAINLESS STEEL, 304, HEX HEAD
NUT, HEX, 1/2 IN, A304, STAINLESS STEEL, HEX
WASHER, FLAT, ROUND, SILICON, BRONZE, FOR, 1/2", BOLT
WASHER, ROUND, 1/2, SS, 1.375" OD
LUG, COMPRESSION, 2H-795AL
CABLE, XLP UG AL 500
GUARD, PVC, CABLE, 2-1/4" X 10'
BANDING, STAINLESS STEEL, 316, 3/4" WIDE, .030 TH
BANDING, BUCKLE, SS, 3/4", FOR BANDING
VIPER ST CONTROL CABLE
SEL 651 CONTROL
CABLE, CONTROL, #10, 4 WIRE
1" CONDUIT, FLEX, AND FITTING
GUARD, ANIMAL, SOLID COVER, STRAIGHT, VERTICAL
GUARD, ANIMAL, L-SHAPED
GUARD, ANIMAL, PT OR VOLTAGE TRANSFORMER
TRANF, POTENTIAL, 25KV, 14400V
NOTES:
1. SEE DWG. 08.06-12A FOR DESIGN SPECIFICATIONS.
2. GROUND RESISTANCE TO BE 15 OHMS OR LESS.
3. CONNECT ENDS OF POWER AND CONTROL CABLES WITH PROTECTIVE ARMORED FLEX TO CONTROL.
4. WHEN INSTALLING UNIT, OPEN JUNCTION BOX PANEL BY REMOVING SCREWS, RECORD 3 PT CORRECTION FACTORS LISTED AND PLACE
ON INSIDE DOOR OF CONTROL. CLOSE JUNCTION BOX PANEL.
5. A 45' CLASS 4 POLE IS THE MINIMUM TO BE USED FOR THIS INSTALLATION. IF JOINT USE ON POLE, CLEARANCES MAY REQUIRE 50' POLE.
6. ISSUE TAPS TO SWITCHES SEPARATELY (WIRE, CONNECTORS, AND LUGS). BOLTS WILL BE ON SWITCH.
7. ALL BOLTS ON PRIMARY CONNECTIONS ARE TO BE TORQUED TO 40 FT-LBS: DO NOT EXCEED!
8. PT'S TO BE LOCATED ON SOURCE SIDE. POWER SOURCE FOR PT'S FROM UNIT 1.
9. SIX ARRESTERS REQUIRED: 3 ON EACH SIDE. CONNECT TO TERMINALS OF RECLOSER AS SHOWN ON DETAIL C ON DWG. 08.06-12A.
10. USE #6 CU WP FOR ARRESTER SECONDARY CONNECTIONS.
11. TOTAL WEIGHT OF THE RECLOSER AND FRAME IS 750 LBS DOES NOT INCLUDE PT'S OR LA'S.
12. NEUTRAL MAY BE DOUBLE DEADENDED OR STRAIGHT THROUGH ON SPOOL AS NEEDED.
13. RECLOSER COMES WITH 10KV ARRESTERS AND 7200 PT'S, REPLACE WITH 18KV ARRESTERS AND 14400 PT'S
AS SHOWN IN THE BILL OF MATERIALS.
3
10/26/15
LOOSIER
BURLISON
ADCOCK
2
7/17/15
LOOSIER
BURLISON
ADCOCK
1
2/10/14
McCONNELL
DANNA
ADCOCK
0
10/7/13
SALAS
DANNA
ADCOCK
BY
CK'D
APPR.
REVISED
RECLOSER ASSEMBLY, THREE-PHASE, VIPER ST
WITH VERTICAL BYPASS SWITCH
- 25KV CONSTRUCTION -
DEC
DEM
DEP
DEF
X
08.06-12C
SOURCE
LOAD
USE WILDLIFE GUARDS
5"
24"
3
4
5
48"
48"
24"
4" MIN. (TYP.)
DETAIL "A"
(2) 9220252997
(4) 9220102213
24"
48"
48"
24"
8
9 10
DETAIL "B"
VIPER ST JUNCTION
BOX PANEL; SEE NOTE 2
ON DWG. 08.06-13B
14
60"
7
4 HOLE
SPADE ON
RECLOSER
14"
LOCKWASHER
1/2" SS
2
6
13
SEE
DETAIL "C"
72"
NUT
#6 WP
ROUND
WASHER
#6 WP
ROUND
BOLT
20
21
11
22 23 24
DETAIL "C"
SEE DETAIL 'A'
27-3/4"
12 SEE NOTE 3
4" MIN.
6"
17
#2 SD BC TANK
GROUND TO
SYSTEM NEUTRAL
1
16
15
#6 SD BC
SEE NOTE 4
18
L1
TERMINAL L1
L2
48" MIN.
BLACK
GREEN - GROUND
BLACK
SIDE VIEW
(TANGENT PHASE OMITTED FOR CLARITY)
SECONDARY
ARRESTER
SECONDARY ARRESTER CONNECTION
IN CONTROL BOX
FRONT VIEW
19
NOTES:
1.
2.
3.
4.
SEE DWG. 08.06-13B FOR BILL OF MATERIALS AND NOTES.
LEADS TO RECLOSER MUST BE A MINIMUM OF 14 INCHES CLEARANCE FROM THROUGH CIRCUIT.
USE COLA CROSSARM BRACKET FOR OUTER TWO SOURCE SIDE ARRESTERS. THIS WILL SHORTEN JUMPER LENGTH.
MOUNT PT JUNCTION BOX (INCLUDED WITH RECLOSER UNIT) ON PT BRACKET. WHOLE PT ASSEMBLY CAN BE BUILT
ON GROUND PRIOR TO INSTALLATION.
3
DEC
2
8/10/15
LOOSIER
BURLISON
ADCOCK
1
4/10/15
LOOSIER
BURLISON
ADCOCK
0
2/13/15
LOOSIER
GUINN
ADCOCK
BY
CK'D
APPR.
REVISED
DEM
DEP
DEF
X
DOUBLE CIRCUIT, THREE-PHASE, VIPER ST
08.06-13A
BILL OF MATERIALS
MACRO UNIT
BUBBLE
NUMBER
COMPATIBLE
UNIT
CU
QTY
ITEM
NUMBER
1
RCVST800E27HF
1
2
SW256RECBYPF
1
3
BKTFBGPIN15138F
6
4
5
IPIN25PF
TTIEF500COVALPF
6
6
6
KLC2H50ALF
6
7
KLC4H79ALF
6
8
IHPTT15F
6
9
BKTFPIS30F
6
10
11
STIE795ALF
AREQOH10F
6
6
12
BKTCOLASTLXARMF
2
13
14
15
16
RCRISER500ALF
JUMP795ALF
RCVIPCAB40F
6
12
1
17
CRIS1UGPVC225WF
2
18
19
20
RCCNTL651GWF
AREQSC120F
RCPTREC15F
1
1
3
21
BKT3PTRCTRISTLF
1
22
23
24
WGRCSLDSVF
WGRCLSHPF
WGRCPTTRF
3
3
3
9220248295
152107
13308
13264
9220248288
13264
13346
152107
9220087868
9220091018
9220068094
10928
12277
13163
155326
10542504
10928
12277
13163
10542504
155464
80212
13264
13346
70431
72361
152107
121434
220202
11213
70101
202112
9220218861
9220267667
9220244739
323422
14111
9220244823
220139
9220085231
9220224674
152107
9220132411
13264
9220252997
9220102213
9220102214
-
ITEM
QTY/
CU
1
2
2
2
1
2
2
2
1
1
1
2
2
4
1
2
2
2
4
2
1
1
2
2
1
1
2
1
1
2
1
12
8
1
1
15
1
1
1
1
2
2
2
1
1
1
DESCRIPTION
RECLOSER, ELECTRONIC, G&W VIPER-ST, HORIZ MOUNT, 27 KV, 800
BOLT, MACHINE, SQ, NUT, 5/8"X12"
WASHER, SQUARE, 2-1/4",SQUARE,FLAT,13/16",HOLE,GALV.
WASHER, LOCK, 5/8 IN, STEEL, GLV, SPRING,DOUBLE COIL
SWITCH, RECLOSER BY-PASS, THREE-PHASE HORIZONTAL
WASHER, LOCK, 5/8 IN, STEEL, GLV, SPRING,DOUBLE COIL
WASHER, 3",SQUARE, CURVED, 13/16" HOLE
BOLT, MACHINE, SQ, NUT, 5/8"X12"
BRACKET, STANDOFF, FIBERGLASS STAND-OFF, 1-3/8" THREAD
INSULATOR, 25 KV POLYMER, 1 3/8" THREAD
TIE, PLASTIC, 2-7/8",F-NECK,INSULATOR
BOLT, MACHINE, 1/2 IN X 2 IN, STAINLESS STEEL, HEX HEAD
NUT, HEX, 1/2 IN, STAINLESS STEEL
WASHER, FLAT, 1/2 IN, SILICON BRONZE, ROUND
LUG, COMPRESSION, 2H 500 AL
WASHER, ROUND, 1/2", SS,1.375" OD
BOLT, MACHINE, 1/2 IN X 2 IN, STAINLESS STEEL, HEX HEAD
NUT, HEX, 1/2 IN, STAINLESS STEEL
WASHER, FLAT, 1/2 IN, SILICON BRONZE, ROUND
WASHER, ROUND, 1/2", SS,1.375" OD
LUG, COMPRESSION, 4HOLE,795,AAC
INSULATOR, POST, TIE, TOP, 25KV
WASHER, LOCK, 5/8 IN, STEEL, GLV, SPRING,DOUBLE COIL
WASHER, 3",SQUARE, CURVED, 13/16" HOLE
BRACKET, STANDOFF, 30 IN, FIBERGLASS
STUD, LINE POST, 5/8"X1-3/4"
BOLT, MACHINE, SQ, NUT, 5/8"X12"
TIE, E-Z, SIDE, F-NECK, 795,AAC
ARRESTER, LIGHTNING, 10KV HD MOV W/SI RUBBER POLY HOUSING
BOLT, CARRIAGE, 3/8 IN, 6 IN, CARBON STEEL
BRACKET, ARRESTOR, LIGHTNING AND CUTOUT TYPE A
CABLE, XLP UG AL 500
CONDUCTOR, ALUMINUM, AAC
PT CONTROL CABLE (INCLUDED FROM MANUFACTURER)
VIPER ST CONTROL CABLE
GUARD, PVC, CABLE, 2-1/4" X 1-'
SCREW, LAG, HX, 1/4' X 2', GALV
SEL 651 CONTROL
ARRESTER, LIGHTNING, SEC 120-240 3 WIRE
TRANSFORMER, POTENTIAL, 15KV, 7200V
BRACKET, MOUNTING, 42 IN, GALVANIZED STEEL, 3 PT MOUNTING
BOLT, MACHINE, SQ, NUT, 5/8"X12"
WASHER, SQUARE, 5/8 INCH SS, 2-1/4 INCH X 2-1/4 INCH
WASHER, LOCK, 5/8 IN, STEEL, GLV, SPRING,DOUBLE COIL
GUARD, ANIMAL, SOLID COVER, STRAIGHT, VERTICAL
GUARD, ANIMAL, L-SHAPED,GUARD
GUARD, ANIMAL, PT OR VOLTAGE TRANSFORMER
NOTES:
1. SEE DWG. 08.06-13A FOR DESIGN SPECIFICATIONS.
2. WHEN INSTALLING UNIT, OPEN JUNCTION BOX PANEL BY REMOVING SCREWS, RECORD 3 PT CORRECTION
FACTORS LISTED AND PLACE ON INSIDE DOOR OF CONTROL. CLOSE JUNCTION BOX PANEL.
3. MINIMUM 55' POLE REQUIRED. WHEN DESIGNING, CONSIDER VERTICAL TENSION ON ADJACENT POLES.
4. ALL BOLTS ON PRIMARY CONNECTIONS ARE TO BE TORQUED TO 40 FT-LBS: DO NOT EXCEED!
5. PT'S TO BE LOCATED ON SOURCE SIDE. POWER SOURCE FOR PT'S FROM UNIT 1.
6. NEUTRAL MAY BE DOUBLE DEADENDED OR STRAIGHT THROUGH ON SPOOL AS NEEDED.
3
DEC
DEM
DEP
DEF
2
1
4/10/15
LOOSIER
BURLISON
ADCOCK
0
2/13/15
LOOSIER
GUINN
ADCOCK
BY
CK'D
APPR.
REVISED
X
DOUBLE CIRCUIT, THREE-PHASE, VIPER ST
08.06-13B
5'-0" MAX.
SOURCE
LOAD
4"
2
6
14"
5
7
SEE
DETAIL "A"
72"
CL BOLT HOLE
SEE NOTE 2
17
13 14 15
16
3
27-3/4"
4
4" MIN.
6"
SEE NOTE 3
SEE NOTE 4
#2 SD BC TANK
GROUND TO
SYSTEM NEUTRAL
1
10
12
8
#6 SD BC
#6 SD BC POLE
GROUND
SIDE VIEW
11
L1
TERMINAL L1
4 HOLE
SPADE ON
RECLOSER
L2
BLACK
GREEN - GROUND
LOCKWASHER
1/2" SS
BOLT
ROUND
WASHER
SECONDARY
ARRESTER
9
38"
NUT
#6 WP
BLACK
MOUNT CONTROL
ON OPPOSITE
SIDE OF POLE
FROM RECLOSER
ROUND
BOLT
#6 WP
SECONDARY ARRESTER CONNECTION
IN CONTROL BOX
BOLT ON TAMPER
GUARDS FOR CONTROL
CABLE PLUG AND
POWER CABLE
5'-0"
DETAIL "A"
NOTES:
1. SEE DWG. 08.06-14B FOR BILL OF MATERIALS AND NOTES.
FRONT VIEW
2. POSITION JUMPERS TO ENSURE MINIMUM OF 10" CLEARANCE BETWEEN THEM.
3. MOUNT PT JUNCTION BOX (INCLUDED WITH RECLOSER UNIT) ON PT BRACKET. WHOLE PT
ASSEMBLY CAN BE BUILT ON GROUND PRIOR TO INSTALLATION.
4. USE COLA CROSSARM BRACKET FOR OUTER TWO SOURCE SIDE ARRESTERS. THIS WILL
SHORTEN JUMPER LENGTH.
3
DEC
DEM
DEP
DEF
2
1
4/10/15
LOOSIER
BURLISON
ADCOCK
0
3/31/15
LOOSIER
BURLISON
ADCOCK
BY
CK'D
APPR.
REVISED
X
VIPER RECLOSER HORIZONTAL CONSTRUCTION
08.06-14A
BILL OF MATERIALS
MACRO UNIT
CU
ITEM
NO.
1
COMPATIBLE
UNIT
QTY
REQ'D
CATALOG
NUMBER
RCVST800E27HF
1
2
SW256RECBYPF
1
3
AREQOH10F
6
4
BKTCOLASTLXARMF
2
5
KLC2H50ALF
6
6
KLC4H79ALF
6
7
RCRISER500ALF
6
8
CRIS1UGPVC225WF
2
9
10
11
12
13
14
15
AREQSC120F
RCVIPCAB40F
RCCNTL651GWF
WGRCSLDSVF
WGRCLSHPF
WGRCPTTRF
1
1
1
3
3
3
16
BKT3PTRCTRISTLF
1
17
RCPTREC15F
3
9220248295
013264
013308
152107
9220248288
220202
011213
070101
010928
012277
013163
155326
10542504
010928
012277
013163
10542504
155464
202112
323422
014111
220139
9220244739
9220244823
9220267667
9220252997
9220102213
9220102214
9220224674
152107
9220132411
013264
9220085231
-
QTY
PER
CU
1
2
2
2
1
1
2
1
2
2
4
1
2
2
2
4
2
1
12
1
15
1
1
1
1
1
1
1
2
2
2
1
DESCRIPTION
RECLOSER, ELECTRONIC, G&W VIPER-ST, HORIZ MOUNT, 27 KV, 800 A
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
WASHER, SQUARE, 2-1/4", FLAT, 13/16" HOLE, GALV.
BOLT, MACHINE, SQ, NUT, 5/8" X 12"
SWITCH, RECLOSER, RECLOSER BY-PASS, THREE-PHASE HORIZONTAL
ARRESTER, LIGHTNING, 10KV HD MOV W/SILICONE RUBBER POLY
BOLT, CARRIAGE, 3/8 IN, 6 IN, CARBON STEEL
BRACKET, ARRESTOR, LIGHTNING AND CUTOUT TYPE A
BOLT, MACHINE, STAINLESS STEEL, HEX HEAD, 1/2" X 2"
NUT, STAINLESS STEEL, HEX, 304 ALLOY, COARSE THREAD
WASHER, FLAT, ROUND, SILICON, BRONZE, FOR 1/2" BOLT
LUG, COMP 2H 500 AL
WASHER, ROUND, RD, 1/2, SS, 1.375" OD
BOLT, MACHINE, STAINLESS STEEL, HEX HEAD, 1/2" X 2"
NUT, STAINLESS STEEL, HEX, 304 ALLOY, COARSE THREAD
WASHER, FLAT, ROUND, SILICON, BRONZE, FOR 1/2" BOLT
WASHER, ROUND, 1/2", SS, BRONZE, FOR 1/2" BOLT
LUG, COMP. 4H, 795 AL
CABLE, XLP UG AL 500
GUARD, PVC, CABLE, 2-1/4" X 10'
SCREW, LAG, HX, 1/4" X 2", GALV.
ARRESTER, LIGHTNING, SEC 120-240 3 WIRE
VIPER ST CONTROL CABLE
SEL 651 CONTROL
PT CONTROL CABLE (INCLUDED FROM MANUFACTURER)
WILDLIFE GUARD RECL SOLID STRAIGHT VERTICAL COVER
WILDLIFE GUARD RECL L-SHAPED COVER
GUARD, ANIMAL, PT OR VOLTAGE TRANSFORMER
BRACKET, MOUNTING, 42 IN, GALVANIZED STEEL, 3 PT MOUNTING
BOLT, MACHINE, 5/8", 11" X 12", STEEL, ANSI C135.1., M
WASHER, SQUARE, 2-1/4 X 2-1/4 X 3/16, GALV
WASHER, LOCK, 5/8", STEEL, GLV, LK, 5/8, COIL, DBL
TRANSFORMER, POTENTIAL, 15KV, 7200V
NOTES:
1. SEE DWG. 08.06-14A FOR RECLOSER DESIGN SPECIFICATIONS.
2. WHEN INSTALLING UNIT, OPEN JUNCTION BOX PANEL BY REMOVING SCREWS, RECORD 3 PT CORRECTION
FACTORS LISTED AND PLACE ON INSIDE DOOR OF CONTROL. CLOSE JUNCTION BOX PANEL.
3. A 45' CLASS POLE IS THE MINIMUM TO BE USED FOR THIS INSTALLATION.
4. ALL BOLTS ON PRIMARY CONNECTIONS ARE TO BE TORQUED AT 40 FT-LBS: DO NOT EXCEED!
5. PT TO BE LOCATED ON THE SOURCE SIDE.
6. USE GROUNDING LUGS ON RECLOSER AND FRAME TO PROPERLY GROUND RECLOSER.
7. NEUTRAL MAY BE DOUBLE DEADEND OR STRAIGHT THROUGH ON SPOOL AS NEEDED.
3
DEC
DEM
DEP
DEF
2
0
X
VIPER RECLOSER HORIZONTAL CONSTRUCTION
1
3/31/15
REVISED
LOOSIER
BURLISON
ADCOCK
BY
CK'D
APPR.
08.06-14B
7.2 OR 14.4 KV
SOURCE
7.2 OR 14.4 KV
SOURCE
BLK
BLK
GRN
X1
BLK
GRN
X2
GND
7.2 OR 14.4 KV
SOURCE
GRN
X1
GND
WHT
X2
WHT
X1
X2
GND
WHT
PT JUNCTION BOX
PT 1
PT 2
PT 3
TO CONTROL BOX
NOTES:
1. X1 WIRE IS BLACK, X2 WIRE IS WHITE, GROUND WIRE IS GREEN.
3
DEC
2
DEM
DEP
DEF
WIRING DIAGRAM FOR PT CLUSTER
X
1
0
12/19/14
REVISED
BURLISON
GUINN
ADCOCK
BY
CK'D
APPR.
FOR G&W VIPER
08.06-15A
POLE
C PHASE
SOURCE
B PHASE
SOURCE
A PHASE
SOURCE
ORANGE
GRN
BLUE
GRN
RED
GRN
WHT
GRN
X1
GRN
X2
X1
GND
X2
X1
GND
WHT
BLACK
BLK
X2
GND
BLK
BLK
BLK
SEE NOTE 5
WHT
BLK
RED
WIRE NUT
YELLOW
WIRE NUT
NOT USED
TO ANPHONAL CONNECTOR
AT BOTTOM OF RECLOSER
ALTERNATE COLOR SCHEME FOR
CONTROL CABLE WITH BLUE,
BLACK, RED, ORANGE AND
YELLOW CONDUCTORS
NOTES:
WIRING DIAGRAM WOULD BE REVERSED IF POLE IS TO THE RIGHT. FOLLOW THIS CONVENTION:
X2 ON ALL PHASES IS GREEN
CAREFULLY REMOVE THE SECONDARY CABLE FROM THE B PHASE. THIS CABLE WILL NEED TO BE REINSTALLED
ON THE C PHASE PT.
BE GROUNDED TO THE LUG ON THE BACK OF THE PT IN ONE OF THESE TWO METHODS.
4. PT CONVERSION KITS HAVE BEEN CREATED AND INCLUDE: 4 STRESS RELIEF CONNECTORS, WIRE NUTS,
5. INSTALL JUMPER FROM THE X2 BUSHING TO THE GROUND BUSHING IN THE "A" PHASE PT.
3
DEC
2
DEM
DEP
DEF
WIRING DIAGRAM FOR PT CLUSTER
X
1
0
12/19/14
REVISED
BURLISON
GUINN
ADCOCK
BY
CK'D
APPR.
ABB 1PT TO 3PT CONVERSION
08.06-15B
F201 - 30A
BATTERY/ BATTERY
CHARGER CIRCUIT
1
F202 - 5A
12 VDC AUX
SUPPLY
2
F412 - 10A
120 VAC POWER
MODULE PROTECTION
3
BILL OF MATERIALS
MACRO UNIT
BUBBLE COMPATIBLE
NUMBER
UNIT
1
2
3
-
-
CU
QTY
ITEM
NUMBER
-
9220273322
9220237204
9220273356
ITEM
QTY/
CU
1
1
1
DESCRIPTION
CONTROL, BATTERY CHARGER CKT, SEL 651 RECLOSER CONTROL - F201-30A
CONTROL, 12VDC AUX SUPPLY, SEL 651 RECLOSER CONTROL - F202-5A
CONTROL, 120VAC POWER MODULE, SEL 651 RECLOSER CONTROL - F412-10A
3
DEC
2
DEM
DEP
DEF
FUSE AND BATTERY FOR SEL 651-R2 CONTROLS
X
1
0
12/19/14
REVISED
BURLISON
GUINN
ADCOCK
BY
CK'D
APPR.
(ABB & VIPER)
08.06-15C
F404 - F406 6A
SOURCE SIDE
PT FUSES
F401 - F403 6A
LOAD SIDE PT FUSES
F-408 AND F410
COPPER PLUG
DUMMY FUSES IN
NEUTRAL CIRCUITS
F407 - 30A
120 VAC POWER
MODULE PROTECTION
F411 15A
120 VAC GFCI
PROTECTION
BILL OF MATERIALS
MACRO UNIT
BUBBLE COMPATIBLE CU
NUMBER
UNIT
QTY
1
2
3
4
-
-
-
ITEM
NUMBER
1028160
9220226465
9220237208
9220284497
ITEM
QTY/
CU
1
1
1
1
DESCRIPTION
CONTROL, PT VOLTAGE, SEL 651 RECLOSER CONTROL - F401-F406-6A
CONTROL, AC POWER SUPPLY & HEATER, SEL 651 RECLOSER CONTROL - F407-F410-30A
CONTROL, GFCI OUTLET, SEL 651 RECLOSER CONTROL - F411-15A
BATTERY, LEAD ACID SEALED, 16 A H, SEL 651R CONTROL
3
2
DEC
2/19/16
LOOSIER
BURLISON
ADCOCK
1
7/17/15
LOOSIER
BURLISON
ADCOCK
0
12/19/14
BURLISON
GUINN
ADCOCK
BY
CK'D
APPR.
REVISED
DEM
DEP
DEF
FUSE AND BATTERY FOR SEL 651-R2 CONTROLS
(ABB & VIPER)
X
08.06-15D
SPECIAL PROVISIONS FOR G&W VIPER ST INSTALLATIONS AT INTERCONNECTIONS WITH IPPS (INDEPENDENT
POWER PRODUCERS):
1. IN DWG. 08.06-11A , THE SIDE OF THE RECLOSER REFERENCED AS THE SOURCE VERTICAL BUSHING SIDE
2. IN DWG. 08.06-11A , THE SIDE OF THE RECLOSER REFERENCED AS THE LOAD HORIZONTAL BUSHING
ITEM # 260123 ) MUST BE
UNBOLTED AND REMOVED FROM THE SWITCH BEFORE IT IS MOUNTED. (EACH PHASE HAS SOURCE AND
LOAD DISCONNECT BLADES THAT ARE PARALLEL TO EACH OTHER, AND THESE ARE LEFT ALONE. ONLY
THE BYPASS BLADE, HORIZONTAL TO THE OTHERS, IS TO BE REMOVED. WHEN READY, THE SWITCHES
WILL HAVE 6 BLADES INSTEAD OF 9. THIS IS DONE BECAUSE AN IPP INTERTIE RECLOSER MUST NEVER BE
BYPASSED, SINCE THERE IS NO BACKUP PROTECTION TO ASSURE PROPER OPERATION OF THE IPP WITH
OPERATION OF THE IPP WITH THE UTILITY.)
4. SEL 651R RELAYS AT IPP INTERCONNECTIONS HAVE SETTINGS, DISPLAY PANELS, AND BUTTONS THAT
ARE NOT THE SAME AS A REGULAR LINE RECLOSER. THE PROPER SETTINGS AND FACEPLATE LABELS ARE
AVAILABLE FROM THE COMPANY PROTECTION ENGINEER AND ARE TO BE APPLIED AT TIME OF RELAY
PROVISIONING.
5. SEE DWGS. 11.09-10 OR 11.09-20 FOR CONSTRUCTION DETAILS FOR THE IPP PRIMARY METERING POLE
LOCATED ONE SPAN AWAY, CLOSER TO THE IPP.
3
DEC
2
DEM
DEP
DEF
SPECIAL PROVISIONS -
X
1
0
4/18/16
REVISED
BRAVO
BURLISON
ADCOCK
BY
CK'D
APPR.
G&W VIPER ST, IPP INTERCONNECTION
08.06-15E
BRACKET - CN 9220272934
ANTENNA - CN 9220272935
INSTALLATION NOTES:
1. FOLLOWING STANDARD OPERATING PROCEDURES AND SAFETY MEASURES, BYPASS THE ABB RECLOSER AND
OPEN ALL THREE SOURCE AND LOAD SIDE DISCONNECTS TO COMPLETELY DE-ENERGIZE THE RECLOSER.
2. DISCONNECT THE BATTERY IN THE EXISTING CONTROL.
3. UNPLUG THE CONTROL CABLE AND SAFELY MOVE IT OUT OF THE WAY.
4. DISCONNECT THE GROUNDING CONNECTION TO THE EXISTING CONTROL.
5. LOOSEN BOLTS AND REMOVE CONTROL FROM POLE.
6. MOUNT THE NEW CONTROL. USE THE SAME TOP BOLT, THE BOTTOM BOLT WILL NEED TO BE REDRILLED.
7. CONNECT GROUND TO CONTROL BOX.
8. PLUG THE CONTROL CABLE INTO THE NEW CONTROL. INSTALL PLUG GUARD OVER THE PLUG
10. INSTALL ANTENNA AND CONDUIT WITH ANTENNA WIRE INSIDE. SECURE CONDUIT TO POLE WITH STRAPS.
11. REMOVE COVER FROM 1" PREDRILLED HOLE IN BOTTOM OF CONTROL. FEED CABLE THROUGH 1" HOLE AND
ATTACH CONDUIT.
12. CONNECT THE 3 ANTENNA WIRES TO THE MODEM INSIDE CONTROL. SEE DWG. 08.06-16B FOR DETAIL.
13. CLOSE THE SOURCE SIDE DISCONNECTS. CONTROL AND MODEM SHOULD COME TO LIFE.
14. FOLLOW INSTRUCTIONS FOR COMMISSIONING CONTROL.
15. WHEN GIVEN OK - CLOSE LOAD SIDE DISCONNECTS AND FOLLOW STANDARD PROCEDURES TO RESTORE
RECLOSER TO SERVICE.
16. WHEN RELOCATING THE CONTROL BOX, IF IT REMAINS ON THE SAME FEEDER, IT WILL
RETAIN THE SAME EQUIPMENT ID. IF THE DEVICE IS RELOCATED TO A DIFFERENT FEEDER,
THEN THE DEVICE WILL REQUIRE A NEW EQUIPMENT ID AND WILL REQUIRE NEW
SETTINGS TO BE UPLOADED.
3
DEC
2
DEM
DEP
DEF
ABB TO SEL 651-R2 CONTROL CONVERSION ON
X
1
0
12/19/14
REVISED
BURLISON
GUINN
ADCOCK
BY
CK'D
APPR.
ABB RECLOSERS
08.06-16A
THERE ARE THREE CABLES COMING FROM THE ANTENNA. THE SMALL CABLE IS THE GPS AND MUST BE SCREWED
INTO THE MIDDLE SPOT ON THE BACK OF THE MODEM. THE TWO LARGER CABLES ARE INTERCHANGEABLE.
SCREW THEM INTO THE OTHER TWO SPOTS.
MODEM - CN 9220272933
MODEM MUST BE CONFIGURED BY TELECOM
3
DEC
2
DEM
DEP
DEF
ABB TO SEL 651-R2 CONTROL CONVERSION ON
X
1
0
12/19/14
REVISED
BURLISON
GUINN
ADCOCK
BY
CK'D
APPR.
ABB RECLOSERS
08.06-16B
5"
6"
2"
11"
4
48"
1
31"
6"
2
3
8
48"
6
35"
5
72"
L1
NEUTRAL
12"
SECONDARY
L2
BLACK
#6 SD BC
TERMINAL L1
GREEN - GROUND
9
BLACK
SECONDARY
ARRESTER
SECONDARY ARRESTER CONNECTION
38"
4 HOLE
SPADE ON
RECLOSER
LOCKWASHER
1/2" SS
BOLT
48" MIN.
BOLT ON TAMPER
GUARD FOR
CONTROL CABLE
PLUG
NUT
#6 BC
ROUND
WASHER
ROUND
BOLT
#6 BC
FRONT VIEW
SIDE VIEW
DETAIL "B"
NOTES:
1.
2.
3.
4.
5.
SEE DWG. 08.06-22B FOR BILL OF MATERIALS.
CONTROL BOX AND SECONDARY REQUIRED FOR ELECTRONIC RECLOSER ONLY.
ISSUE RECLOSER AND ELECTRONIC CONTROL SEPARATELY.
RECLOSER MAY BE REVERSED IN HANGER TO ACCOMMODATE SOURCE AND LOAD POSITION.
WHEN END MOUNTING THREE-PHASE RECLOSER, USE A MINIMUM OF A 45 FT. CLASS 4 WOOD POLE.
3
RECLOSER ASSEMBLY, THREE-PHASE, VERTICAL
2
1
11/6/13
SALAS
0
10/19/10
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
DANNA
ADCOCK
600 AMP SWITCH
DWG.
08.06-22A
BILL OF MATERIALS
MACRO UNIT
CU
ITEM
NO.
COMPATIBLE
UNIT
QTY
REQ'D
1
SW156BYPF
3
2
3
4
5
BKTFBGPIN15138F
IPIN25PF
TTIEF500COVALPF
AREQOH10F
4
4
4
6
6
KLC2H50ALF
6
7
8
KLC2H50AL90DF
RCRISER500ALF
6
6
9
CRIS1UGPVC225CF
2
10
AREQSC120F
1
11
GOCE6F
1
-
CATALOG
NUMBER
013264
013308
152107
260123
9220087868
9220091018
9220068094
220202
010928
012277
013163
155326
10542504
9220068102
202112
323422
434122
434142
220139
013264
013308
152107
153111
160123
190404
QTY
PER
CU
2
2
2
1
1
1
1
1
2
2
4
1
2
1
12
1
0.2
3
1
2
2
1
1
1
4
DESCRIPTION
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
WASHER, SQUARE, 2-1/4", FLAT, 13/16" HOLE, GALV.
BOLT, MACH, SQ, NUT, 5/8" X 12"
SWITCH, BYPASS, 3-SLD BLADE DISC,, 15KV, LBK
BRACKET, FIBERGLASS STAND-OFF, 1-3/8" THREAD
INSULATOR, 25 KV POLYMER, 1 3/8" THREAD
PLASTIC TIE WRAP FOR 2-7/8" F-NECK INSULATOR
ARRESTER, LIGHTNING, 10KV HD MOV W/SILICONE RUBBER POLY
BOLT, MACHINE, STAINLESS, STEEL, HEX, HEAD, 1/2" X 2"
NUT, STAINLESS, STEEL, HEX, 304, ALLOY, COARSE THREAD
WASHER, FLAT, ROUND, SILICON, BRONZE, FOR 1/2" BOLT
LUG, COMP 2H 500 AL
WASHER, ROUND, RD, 1/2, SS, 1.375" OD
LUG, 2-HOLE, TIN-PLATED, NEMA, 90 DEGREE
CABLE, XLP UG AL 500
GUARD, PVC, CABLE, 2-1/4" X 10'
BANDING, STAINLESS STEEL, 316, SS, 3/4" WIDE, .030 TH
BANDING, BUCKLE, SS, 3/4", FOR BANDING
ARRESTER, LIGHTNING, SEC 120-240 3 WIRE
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
WASHER, SQUARE, 2-1/4", FLAT, 13/16" HOLE, GALV.
BOLT, MACH, SQ, NUT, 5/8" X 12"
CONNECTOR, COMP, AL, A=2/0STR-2SOL, B=2STR-6SOL
CONNECTOR, GND, 5/8, ROD, 2, CU
WIRE, COPPER, #6, SOFT DRAWN, CU, BR, SDW, SLD, #6
ADDITIONAL MATERIALS FOR ELECTRONIC RECLOSER ONLY
MACRO UNIT
-
CU/CN
ITEM
NO.
16
17
18
19
20
21
22
COMPATIBLE
UNIT
QTY
REQ'D
CATALOG
NUMBER
-
-
220133
323422
373379
372172
381674
372102
-
QTY
PER
CU
1
2
2
1
1
1
1
DESCRIPTION
ARRESTER, SECONDARY, 650V
CABLE GUARD, PLASTIC, 2-1/4" X 10"
ADAPTER, PVC, MALE, SCH 40
NUT, 1", STEEL CONDUIT
CONDUIT, 1", PVC, SCH 40
CONTROL, ELECTRONIC (ISSUE SEPARATELY)
NOTES:
1. SEE DWG 08.06-22A FOR DESIGN SPECIFICATIONS.
2. SEE DWG 03.06-04 FOR PIN INSULATOR DETAILS.
3
RECLOSER ASSEMBLY, THREE-PHASE, VERTICAL,
2
R
1
0
10/19/10
REVISED
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
600 AMP SWITCH
DWG.
08.06-22B
SWITCH, BYPASS, SINGLE-PHASE
1
2
15 KV SWITCH, BYPASS, SINGLE-PHASE
BRACKET IS INCLUDED WITH SWITCH
25 KV SWITCH, BYPASS, SINGLE-PHASE
BRACKET IS INCLUDED WITH SWITCH
BILL OF MATERIALS
CU
ITEM
NO.
MACRO UNIT
COMPATIBLE
UNIT
QTY
REQ'D
1
SW156BYPF
1
2
SW256BYPF
1
-
CATALOG
NUMBER
013264
013308
152107
260123
013264
013308
152107
260552
QTY
PER
CU
2
2
2
1
2
2
2
1
DESCRIPTION
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
WASHER, SQUARE, 2-1/4", SQUARE, FLAT
BOLT, MACH, SQ, NUT, 5/8" X 12"
SWITCH, BYPASS, 600A, 15KV, W/ BRACKET
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
WASHER, SQUARE, 2-1/4", SQUARE, FLAT
BOLT, MACH, SQ, NUT, 5/8" X 12"
SWITCH, BYPASS, 600A, 25KV, W/ BRACKET
NOTES:
1. THE FACE OF POLE SHOULD BE LEFT CLEAR FOR OPERATION OF VERTICAL MOUNTED SOLID BLADE SWITCHES.
AVOID MOUNTING STREET LIGHT BRACKETS AND OTHER SIMILAR EQUIPMENT ON THESE POLES.
3
2
BYPASS SWITCHES
1
0
8/23/10
REVISED
R
GUINN
GUINN
ELKINS
DWG.
BY
CK'D
APPR.
08.10-10
5"
9"
NEUTRAL
4"
4"
28-3/4"
44"
SEE NOTE 4
15-1/4"
2
4"
4"
28-3/4"
4
1
SEE NOTE 3
44"
6
3
15-1/4"
4"
4"
28-3/4"
5
PLAN VIEW
72"
#6 SD BC
FRONT VIEW
NOTES:
1. THIS POLE SHOULD BE OFFSET WHEN POSSIBLE SO THAT CONDUCTORS STAY IN LINE.
2. SEE DWG. 08.10-12B FOR BILL OF MATERIALS.
3. ARRESTERS APPLIED ONLY IN NORMAL OPEN CONFIGURATION.
4. CAN USE EITHER 20" OR 30" STANDOFF BRACKET AS REQUIRED BY FIELD CONDITIONS.
3
7/1/15
LOOSIER
BURLISON
ADCOCK
2
3/31/15
LOOSIER
WHITE
ADCOCK
1
1/23/13
DANNA
DANNA
ADCOCK
0
11/29/10
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
DEC
DEM
DEP
DEF
X
SWITCH MOUNTING IN VERTICAL DOUBLE CIRCUIT
08.10-12A
BILL OF MATERIALS
MACRO UNIT
CU
ITEM
NO.
COMPATIBLE
UNIT
QTY
REQ'D
1
SW156SBDF
3
2
BKTLASWBKTSTLF
3
3
BKTSBDSWSTLF
3
4
AREQOH10F
9
5
BKTCOLASNGSTLF
3
6
KHLC7933F
6
-
CATALOG
NUMBER
010928
012277
013128
013407
152074
260136
010928
012277
070283
10542504
013264
013308
070282
152107
220202
193511
013264
013308
152106
311263
9220184794
QTY
PER
CU
4
4
4
8
2
1
2
2
1
2
2
2
1
2
1
2
2
2
2
1
1
DESCRIPTION
BOLT, MACHINE, STAINLESS, STEEL, HEX, HEAD,1 /2"X2"
NUT, HEX, 1/2 IN, A304, STAINLESS STEEL
WASHER, ROUND, BELLEVILLE SPRING, FOR 1/2" BOLT
WASHER, ROUND, FLAT, STAINLESS STEEL, 304, ALLOY, FOR,1/2"
BOLT, MACH, HEX, HD, 1/2"X2"
SWITCH, DISCONNECT, SOLID BLADE, 15KV, 600A, 1PH, SWITCH
BOLT, MACHINE, STAINLESS, STEEL, HEX, HEAD, 1/2" X 2"
NUT, STAINLESS, STEEL, HEX, 304, ALLOY, COARSE, THREAD
BRACKET, MNTG SWITCH ARSTR
WASHER, RD, 1/2, SS, 1.375" OD
WASHER, SPRING, COIL, STEEL, 5/8", BOLT, GALV
WASHER, SQUARE, 2-1/4", SQUARE, FLAT, 13/16
BRACKET, MNTG WD/CNCR POLE
BOLT, MACH, SQ, NUT, 5/8" X 12"
ARRESTER, LIGHTNING, 10KV HD MOV W/SILICONE RUBBER P
CABLE, 600V, #6 SD BC
WASHER, SPRING, COIL, STEEL, FOR 5/8", BOLT, GALV.
WASHER, 2-1/4", SQUARE, FLAT, 13/16", HOLE, GALV.
BOLT, MACH, SQ, NUT, 5/8" X 10"
BRACKET, SGL MT
CONNECTOR, HOT LINE CLAMP, 795 MCM TO 336 MCM
NOTES:
1. SEE DWG. 08.10-12A FOR DESIGN SPECIFICATIONS.
3
2
4/9/13
McCONNELL
DANNA
ADCOCK
1
1/6/12
HOFFMAN
BURLISON
ELKINS
0
11/29/10
HOFFMAN
GUINN
ELKINS
DWG.
BY
CK'D
APPR.
08.10-12B
REVISED
SWITCH MOUNTING IN VERTICAL DOUBLE CIRCUIT
3
DETAIL "A"
PLAN VIEW
2
3" TYP.
5"
CL BOLT HOLE (TYP.)
8"
3" TYP.
28-3/4"
22"
SEE DETAIL "A"
1
44"
15-1/4"
22"
SEE NOTE 4
28-3/4"
22"
16" MIN. TYP.
44"
15-1/4"
22"
28-3/4"
TO STRAIGHT
THROUGH
CIRCUIT
(FAR SIDE
CONDUCTOR
NOT SHOWN
FOR CLARITY)
4
72"
NEUTRAL
FRONT VIEW
SIDE VIEW
NOTES:
1. SEE DWG 08.10-14B FOR BILL OF MATERIALS.
2. THIS POLE SHOULD BE OFFSET WHEN POSSIBLE SO THAT CONDUCTORS STAY IN LINE.
3. MAINTAIN A MINIMUM CLEARANCE OF 16" BETWEEN JUMPERS AND PHASES.
4. CAN USE EITHER 20" OR 30" STANDOFF BRACKET AS REQUIRED BY FIELD CONDITIONS.
3
2
DEC
6/17/15
LOOSIER
BURLISON
ADCOCK
1
11/6/13
SALAS
DANNA
ADCOCK
0
8/23/10
GUINN
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
DEM
DEP
DEF
600 AMP DOUBLE CIRCUIT
TIE SWITCH
X
08.10-14A
BILL OF MATERIALS
MACRO UNIT
CU/CN
ITEM
NO.
COMPATIBLE
UNIT
QTY
REQ'D
1
SW156SBDF
3
2
BKTSBDSWSTLF
3
3
4
KWP4H79F
-
3
-
-
CATALOG
NUMBER
260136
012277
013128
010928
013407
152074
070282
013264
152107
013308
165288
9220068328
QTY
PER
CU
1
4
4
4
8
2
1
2
2
2
1
2
DESCRIPTION
SWITCH, SOLID BLADE 600 AMP
NUT, SS, HEX
WASHER, ROUND, BELLEVILLE, SPRING
BOLT, MACHINE, SS, HEX HEAD, 1/2" X 2"
WASHER, ROUND, FLAT, SS
BOLT, MACHINE, HEX HEAD, 1/2" X 2"
BRACKET, MOUNTING WD/CONCRETE POLE
WASHER, SPRING, COIL, FOR 5/8", STL, GALV.
BOLT, MACHINE, SQ, 5/8" X 12"
WASHER, 2-1/4", SQUARE FLAT, 13/16" HOLE
CONNECTOR, WEDGE, 4-HOLE, 795 AAC
SIGN, CAUTION FEEDER TIE SWITCH
NOTES:
1. SEE DWG 08.10-14A FOR DESIGN SPECIFICATIONS.
3
2
600 AMP DOUBLE CIRCUIT
1
4/9/13
McCONNELL
0
8/23/10
GUINN
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
DANNA
ADCOCK
TIE SWITCH
DWG.
08.10-14B
5"
LOAD
LINE
2" TYP.
36"
4
5
3
2
SEE NOTE 2
36"
1
72"
NEUTRAL
#6 SD BC
#6 SD BC
FRONT VIEW
SIDE VIEW
BILL OF MATERIALS
MACRO UNIT
CU
ITEM
NO.
1
1
COMPATIBLE
UNIT
QTY
REQ'D
CATALOG
NUMBER
SW153COSBDF
SW253COSBDF
3
3
2
BKTCOLADBLSTLF
3
3
BKTCOLASNGSTLF
3
4
AREQOH10F
KHLC40N6F
KHLC7933F
6
6
6
9220210916
9220210993
013264
013308
070106
152107
013264
013308
152106
311263
220202
9220184790
9220184794
-
-
5
QTY
PER
CU
1
1
2
2
1
2
2
2
2
1
1
1
1
DESCRIPTION
15KV CUTOUT WITH 300A SOLID DOOR
25KV CUTOUT WITH 300A SOLID DOOR
WASHER, LOCK, 5/8", STEEL, GLV, SPRING, DOUBLE COIL, STEEL, F
WASHER, SQUARE, 2-1/4", FLAT, 13/16" HOLD, GLV
BRACKET, ARRESTER AND CUTOUT, DBL MNTG
BOLT, MACHINE, SQUARE, NUT, 5/8" X 12"
WASHER, SPRING, COIL, STEEL, FOR 5/8", BOLT, GALV.
WASHER, SQUARE, 2-1/4", FLAT, 13/16" HOLE, GALV.
BOLT, MACHINE, 5/8" X 10", STEEL, A-ASTM A307, GALV
BRACKET, SINGLE MOUNT
ARRESTER, LIGHTNING, 10KV HD MOV W/SILICONE RUBBER POLY
CLAMP, HOT LINE, ALUM, SMALL, 4/0
CLAMP, HOT LINE, ALUM, LARGE, 336-795
NOTES:
1. 300 AMP DISCONNECT IS AVAILABLE 15KV AND 25KV (COASTAL AND HOLOPAW).
2. ARRESTERS APPLIED ONLY IN NORMAL OPEN CONFIGURATION.
5
3/31/15
4
5/31/13
3
4/15/13
0
8/23/10
REVISED
LOOSIER
WHITE
ADCOCK
DANNA
ADCOCK
DANNA
ADCOCK
GUINN
GUINN
ELKINS
BY
CK'D
APPR.
DEC
DEM
DEP
SWITCH ASSEMBLY, 300 AMP,
SOLID BLADE, VERTICAL
DEF
X
08.10-16
5
PLAN VIEW
3
CL BOLT HOLE (TYP.)
8"
5"
28-3/4"
1
6
44"
15-1/4"
28-3/4"
2
4
44"
SEE NOTE 2
15-1/4"
28-3/4"
72"
1
NEUTRAL
#6 SD BC
FRONT VIEW
SIDE VIEW
NOTES:
1. SEE DWG. 08.10-18B FOR BILL OF MATERIALS.
2. ARRESTERS APPLIED ONLY IN NORMAL OPEN CONFIGURATION.
5
6/17/15
LOOSIER
BURLISON
ADCOCK
4
3/31/15
LOOSIER
WHITE
ADCOCK
3
10/29/14
LOOSIER
DANNA
ADCOCK
0
11/29/10
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
DEC
DEM
DEP
DEF
SWITCH ASSEMBLY, 600 AMP,
SOLID BLADE, VERTICAL
X
08.10-18A
BILL OF MATERIALS
MACRO UNIT
CU
ITEM
NO.
-
COMPATIBLE
UNIT
QTY
REQ'D
1
SW156SBDF
3
2
BKTLASWBKTSTLF
3
3
BKTSBDSWSTLF
3
4
5
AREQOH10F
KHLC7933F
6
6
6
KLC4H79ALF
6
CATALOG
NUMBER
010928
012277
013128
013407
152074
260136
010928
012277
070283
10542504
013264
013308
070282
152107
220202
9220184794
10928
12277
13163
155464
10542504
QTY
PER
CU
4
4
4
8
2
1
2
2
1
2
2
2
1
2
1
1
4
4
8
1
4
DESCRIPTION
BOLT, MACHINE, STAINLESS, STEEL, HEX, HEAD,1 /2"X2"
NUT, HEX, 1/2 IN, A304, STAINLESS STEEL
WASHER, ROUND, BELLEVILLE SPRING, FOR 1/2" BOLT
WASHER, ROUND, FLAT, STAINLESS STEEL, 304, ALLOY, FOR,1/2"
BOLT, MACH, HEX, HD, 1/2"X2"
SWITCH, DISCONNECT, SOLID BLADE, 15KV, 600A, 1PH, SWITCH
BOLT, MACHINE, STAINLESS, STEEL, HEX, HEAD, 1/2" X 2"
NUT, STAINLESS, STEEL, HEX, 304, ALLOY, COARSE, THREAD
BRACKET, MNTG SWITCH ARSTR
WASHER, RD, 1/2, SS, 1.375" OD
WASHER, SPRING, COIL, STEEL, 5/8", BOLT, GALV
WASHER, SQUARE, 2-1/4", SQUARE, FLAT, 13/16
BRACKET, MNTG WD/CNCR POLE
BOLT, MACH, SQ, NUT, 5/8" X 12"
ARRESTER, LIGHTNING, 10KV HD MOV W/SILICONE RUBBER P
CONNECTOR, HOT LINE CLAMP, 795 MCM TO 336 MCM
BOLT, MACHINE, 1/2 IN, 2 IN, STAINLESS STEEL, 304, HEX HEAD
NUT, HEX, 1/2 IN, A304, STAINLESS STEEL, 304, ALLOY, COARSE
WASHER, FLAT, 1/2 IN, SILICON BRONZE, FLAT, ROUND, SILICON
LUG, COMPRESSION, 4 HOLE, 795, AAC
WASHER, ROUND, 1/2, SS, 1.375" OD
3
2
DETAIL
SWITCH BRACKET
NOTES:
1. SEE DWG. 08.10-18A FOR DESIGN SPECIFICATIONS.
5
6/17/15
LOOSIER
BURLISON
ADCOCK
4
3/31/15
LOOSIER
WHITE
ADCOCK
3
7/16/14
LOOSIER
DANNA
ADCOCK
0
11/29/10
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
DEC
DEM
DEP
DEF
SWITCH ASSEMBLY, 600 AMP,
SOLID BLADE, VERTICAL
X
08.10-18B
PLAN VIEW
KHLC40N6F
OR
KHLC7933F
6" TYP.
6"
24"
6"
60"
FRONT VIEW
SIDE VIEW
NOTES:
1. IN LOCATIONS WHERE THE SWITCH COULD BE USED TO TRANSFER LOAD AND COULD BE LEFT IN THE
OPEN POSITION FOR AN EXTENDED PERIOD OF TIME, ENGINEERING SHOULD CALL FOR LIGHTNING
ARRESTERS ON BOTH SIDES OF THE SWITCH.
3
SWITCH ASSEMBLY, 300 AMP, SOLID BLADE
2
1
8/31/11
BURLISON
0
11/5/10
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
BURLISON
ELKINS
HORIZONTAL
DWG.
08.10-20
10"
2
SEE NOTE 3
20"
14"
20"
18"
38"
14"
10"
34"
14"
4
5"
3
1
72"
#6 SD BC
FRONT VIEW
SIDE VIEW
BILL OF MATERIALS
MACRO UNIT
CU
ITEM
NO.
COMPATIBLE
UNIT
QTY
REQ'D
1
SW156UHSBDF
3
1
SW256UHSBDF
3
2
AREQOH10F
6
3
ARMD8LW36FSF
1
4
KHLC7933F
6
-
CATALOG
NUMBER
260136
070793
260547
070793
220202
011209
011313
013264
013308
014114
031113
071306
9220184794
QTY
PER
CU
1
1
1
1
1
4
3
1
10
2
2
4
1
DESCRIPTION
SWITCH, DISCONNECT, SOLID BLADE, 15KV, 600A, SINGLE-PHASE
PLATE, SW BACKING
SWITCH, DISCONNECT, SOLID BLADE, 25KV, 600A, SINGLE-PHASE
PLATE, SW BACKING
ARRESTER, LIGHTNING, 10KV HD MOV W/SILICONE RUBBER POLY
BOLT, CARRIAGE, 3/8" X 4-1/2"
BOLT, DOUBLE ARMING, 5/8", 20", STEEL, WITH 4 NUTS
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
WASHER, SQUARE, 2-1/4", FLAT, 13/16" HOLE, GALV.
SCREW, LAG, 1/2" X 4", STEEL, GALV.
CROSSARM, WOOD, 8', MS-121-F, LIGHT
BRACE, FLAT, GALV, STEEL, 36"
CONNECTOR, HOT LINE CLAMP, 795 MCM TO 336 MCM
NOTES:
1. 600 AMP SWITCH IS AVAILABLE FOR 15KV AND 25KV (COASTAL AND HOLOPAW).
2. SEE DWG. 03.11-01B FOR REQUIRED CROSSARM.
3. ARRESTERS APPLIED ONLY IN NORMAL OPEN CONFIGURATION.
3
DEC
2
3/31/15
1
5/31/13
0
8/23/10
REVISED
LOOSIER
WHITE
ADCOCK
DANNA
ADCOCK
GUINN
GUINN
ELKINS
BY
CK'D
APPR.
DEM
DEP
SWITCH ASSEMBLY, 600 AMP, SOLID BLADE
HORIZONTAL
DEF
X
08.10-22
25"
4"
17"
PLATED TERMINAL
PADS
DEAD-ENDING
HOLE
2
3
4
4"
BLADE STOP PIN
1
2-3/8"
11/16" DIA.
PULL-OFF-HOLE
1-1/4" DIA.
LOADBREAK HOOK
15-13/16"
BILL OF MATERIALS
MACRO UNIT
CU
ITEM
NO.
COMPATIBLE
UNIT
QTY
REQ'D
1
SW156ILSBDF
1
DECLMP(WIRE)F
IDES25PF
KLC2H(WIRE)ALF
2
2
2
2
3
4
CATALOG
NUMBER
0000010928
0000012277
0000013128
0000013407
0000434241
0000080577
-
QTY
PER
CU
4
4
4
8
1
1
1
1
DESCRIPTION
BOLT, MACHINE, 1/2 IN, 2 IN, SS, 304, HEX HEAD
NUT, HEX, 1/2 IN, A304, STAINLESS STEEL, HEX
WASHER, ROUND, BELLEVILLE SPRING, FOR 1/2" BOLT
WASHER, ROUND, ROUND,FLAT,SS,304,ALLOY,FOR,1/2"
SWITCH, DISCONNECT TEMP
DEADEND CLAMP
INSULATOR, DEADEND, POLYMER,25KV,DE,SILICONE, 15KV
LUG, COMPRESSION, 2 HOLE
NOTES:
1. SEE DWG. 08.10-18A FOR THE PREFERRED 600 AMP SWITCH INSTALLATION. INLINE SWITCHES MAY BE USED
TO FACILITATE CONSTRUCTION, RESTORATION OR REPAIR. WHEN USED FOR THESE PURPOSES, THEY SHOULD
BE REMOVED AT THE COMPLETION OF WORK. INLINE SWITCHES MAY BE USED FOR A PERMANENT INSTALLATION
WHEN THE PREFERRED INSTALLATION IS IMPRACTICAL OR IMPOSSIBLE.
3
DEC
2
9/4/14
LOOSIER
DANNA
ADCOCK
1
11/21/11
ROBESON
BURLISON
ELKINS
0
11/5/10
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
DEM
DEP
DEF
X
600 AMP INLINE DISCONNECT
08.10-24
5"
LINE
4"
12"
28-3/4"
44"
44"
LOAD
3
15-1/4"
44"
44"
2
PLAN VIEW
TANGENT CONSTRUCTION
1
72"
NEUTRAL
4"
FRONT VIEW
BILL OF MATERIALS
MACRO UNIT
CU
ITEM
NO.
COMPATIBLE
UNIT
QTY
REQ'D
1
SW156SBDF
3
2
BKTSBDSWSTLF
3
3
KWP4H79F
3
-
CATALOG
NUMBER
260136
012277
013128
010928
013407
152074
070282
013264
152107
013308
165288
QTY
PER
CU
1
4
4
4
8
2
1
2
2
2
1
DESCRIPTION
SWITCH, SOLID BLADE 600 AMP
NUT, SS, HEX
WASHER, ROUND, BELLEVILLE, SPRING
BOLT, MACHINE, SS, HEX HEAD, 1/2" X 2"
WASHER, ROUND, FLAT, SS
BOLT, MACHINE, HEX HEAD, 1/2" X 2"
BRACKET, MOUNTING WD/CONCRETE POLE
WASHER, SPRING, COIL, FOR 5/8", STL, GALV.
BOLT, MACHINE, SQ, 5/8" X 12"
WASHER, 2-1/4", SQUARE FLAT, 13/16" HOLE
CONNECTOR, WEDGE, 4-HOLE, 795 AAC
NOTES:
1. THE INTENT OF THIS DRAWING IS TO SHOW PHASE SPACING AND CIRCUIT ARRANGEMENT. PRIMARY SUPPORT
CONFIGURATION MAY VARY.
2. POLE GAINS ( ISGAINGRIDF FOR 15/25KV INSULATORS OR ISGAINGRID55F FOR 35KV INSULATORS) ARE REQUIRED
FOR POST INSULATOR INSTALLATIONS ON WOOD POLES WHEN THE POLE DOES NOT HAVE A SLAB GAIN FOR ALL
CONDUCTOR SIZES.WHEN THE CONDUCTOR IS 336.4 KCMIL OR LARGER, USE POLE GAIN EVEN IF SLAB GAIN
EXISTS. POLE GAINS ARE NOT REQUIRED FOR INSULATORS USED FOR JUMPERS. SLACK SPANS WITH 336 AND
795 CONDUCTORS REQUIRE A POLE GAIN.
3. SEE SPECIFIC CONFIGURATION DRAWINGS FOR ADDITIONAL DETAILS.
3
2
4/9/13
McCONNELL
DANNA
ADCOCK
1
3/21/13
McCONNELL
DANNA
ADCOCK
0
1/23/13
ROBESON
GUINN
ADCOCK
BY
CK'D
APPR.
REVISED
VERTICAL TANGENT CROSSING
WITH 600 AMP DISCONNECTS
DWG.
08.10-26
7
8
5"
6"
24"
48"
10
24"
6"
9
48"
4
35"
6
72"
2
7
8
14
#6 SD BC
3
#6 SD BC
#2 SD BC
13
1
120/208V
PT SOURCE
15 16 17 18 19 20
11
LASH 200' CT & SW
CABLE TO AERIAL
QUADRUPLEX
(COIL EXCESS)
21
#6 SD BC
12 22
20-1/8"
48" MIN.
FRONT VIEW
SIDE VIEW
NOTES:
1. ENGINEER MUST SPECIFY JUMPER AND PRIMARY CONNECTOR SIZE.
2. REFER TO DWG. 08.12-01 FOR WIRING DIAGRAM.
3. SEE DWG. 08.12-02B FOR BILL OF MATERIALS.
4. BOND TANK AND FRAME WITH #2 SD BC TO SYSTEM NEUTRAL.
5. WHEN USING AS LOAD CONTROL ON A PRIMARY METERED CUSTOMER, PLACE THE VLR SWITCH ON THE LOAD
SIDE OF THE PRIMARY METERING INSTALLATION.
3
2
11/11/13
1
5/24/13
0
11/29/10
REVISED
DANNA
DANNA
ADCOCK
DANNA
ADCOCK
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
VLR LOAD CONTROL AND
AUTO TRANSFER CONTROL SWITCH
DWG.
08.12-02A
BILL OF MATERIALS
CU
ITEM
NO.
MACRO UNIT
COMPATIBLE
UNIT
QTY
REQ'D
CATALOG
NUMBER
QTY
PER
CU
DESCRIPTION
VLR VERTICAL FRAMING - ORDER SWITCH, CONTROL AND CABLES SEPARATELY
SWOVLRFRMFM
1
BKTOSVLREPF
1
2
3
4
AREQOH10F
BKTCOLASTLXARMF
KHLC40N6F
6
6
6
5
BKTFPIS20F
4
6
ISSTUDBOLT5814F
2
7
8
9
IHPTT15F
HTIEN4AACF
RCRISER40ALF
6
6
6
10
SW156BYPF
3
11
12
13
AREQSC120F
SWOSCADACNTKITF
FUSESEC30F
1
1
1
070467
013229
013264
013346
152094
152107
220202
070101
9220184790
070430
072361
152107
013346
013264
013264
072368
080212
200306
202111
260123
013264
013308
152107
010928
013128
013407
012277
220139
263165
230464
1
12
2
2
6
2
1
1
1
1
1
2
2
2
1
1
1
5
8
1
2
2
2
8
8
16
8
1
1
1
BRACKET, RCLSR 3PH TY 3H E-P
WASHER, ROUND, FLAT, 1/2", BOLT
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
WASHER, 3", SQUARE, CURVED, 13/16", HOLE
BOLT, MACHINE, 1/2" X 3-1/2"
BOLT, MACH, SQ, NUT, 5/8" X 12"
ARRESTER, LIGHTNING, 10KV HD MOV W/SILICONE RUBBER POLY
BRACKET, LA & CO TY A
CLAMP, HOT LINE, ALUMINUM
BRACKET, FIBERGLASS, STAND-OFF, 20"
STUD, LINE POST, 5/8" X 1-3/4"- 3/4 X 1
BOLT, MACH, SQ, NUT, 5/8" X 12"
WASHER, 3", SQUARE, CURVED, 13/16", HOLE
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
STUD, LINE POST, 5/8" X 14"
INSULATOR, POST, TIE TOP, 15/25KV, WITHOUT STUD
WIRE, AL, SLD, BR, SDW, #4, TIEWIRE
CABLE, XLP UG AL 4/0
SWITCH, BY-PASS, 3-SLD BLADE DISC, 15KV, LBK HOOKS, 600A
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
WASHER, SQUARE, 2-1/4", FLAT, 13/16", HOLE, GALV.
BOLT, MACH, SQ, NUT, 5/8" X 12"
BOLT, MACHINE, STAINLESS, STEEL, HEX, HEAD, 1/2" X 2"
WASHER, ROUND, BELLEVILLE SPRING, FOR 1/2" BOLT
WASHER, ROUND, STAINLESS STEEL, 304 ALLOY, FOR 1/2" BOLT
NUT, HEX, 1/2 IN, A304, STAINLESS STEEL, COARSE, THREAD, 1
ARRESTER, LIGHTNING, SEC 120-240 3 WIRE*
RISER, KIT-SCADA CONTROL
FUSE, SEC INS 30 AMP
VLR SWITCH USED FOR LOAD CONTROL - SWITCH AND CONTROL CABLE
14
-
SW154VLRF
1
263138
264219
192281
200306
470114
1
1
30
5
6
SWITCH, OIL 15KV 3 RC 400A8
CABLE, IS1 VLR SW CNTRL 35
CABLE, CONTROL, #10, 2 - CONDUCTOR
WIRE, AL, SLD, BR, SDW, #4, TIEWIRE
GUARD, TRANSFORMER, WILDLIFE, ROUND, GRAY MIN. 9"
VLR SWITCH USED FOR AUTO SOURCE TRANSFER SCHEME - SWITCH ONLY - ORDER CABLES SEPARATELY
-
14
15
16
17
18
19
20
SW154VLRFBF
SWOS1CAB35F
SWOS1CAB45SWF
SWOS1CAB45CTF
SWOS1CAB200CTF
SWOS1CAB200SWF
SWOS1CAB45FBF
1
1
1
1
1
1
1
-
21
CRIS1UGPVC225CF
1
-
22
SWOHASTCNTLSF
1
263136
264219
264210
264208
264211
264212
264209
323422
434122
434142
1
1
1
1
1
1
1
1
0.2
3
SWITCH, AUTO, XFER FAULT BL
CABLE, IS1 VLR SW CNTRL 35'
CABLE, CNTL, TYPE S, 45' SW
CABLE, CNTL, TYPE S, 45' CT
CABLE, CNTL, TYPE S, 200' CT
CABLE, CNTL, TYPE S, 200' SW
CABLE, CNTL, TYPE S, 45' FB
GUARD, PVC, CABLE, 2-1/4"X10'
BANDING, STAINLESS STEEL, 316, SS, 3/4", WIDE, .030, TH
BANDING, BUCKLE, SS, 3/4", FOR BANDING
TYPE S CONTROL - SPECIAL ORDER
264207
1
CONTROL, OILSW TYPE S 3PH
NOTES:
1. SEE DWG. 08.12-02A FOR DESIGN SPECIFICATIONS.
2. SEE DWG. 08.13-05 FOR AUTO TRANSFER WIRING DETAIL.
3
2
VLR LOAD CONTROL AND
1
5/24/13
0
11/29/10
REVISED
DANNA
ADCOCK
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
AUTO TRANSFER CONTROL SWITCH
DWG.
08.12-02B
4
5
5"
6"
24"
3
4"
4
5
48"
7
24"
2
6"
6
48"
42"
72"
1
24"
#2 SD BC
6"
9
11
8
#6 SD BC
9
20-1/8"
48" MIN.
FRONT VIEW
SIDE VIEW
NOTES:
1. ENGINEER MUST SPECIFY JUMPER AND PRIMARY CONNECTOR SIZE.
2. REFER TO DWG. 08.12-04C FOR WIRING DIAGRAM.
3. SEE DWG. 08.12-04B FOR BILL OF MATERIALS.
4. BOND TANK AND FRAME WITH #2 SD BC TO SYSTEM NEUTRAL.
5. ON A PRIMARY METERED CUSTOMER, PLACE THE VERSAVAC SWITCH ON THE LOAD SIDE
OF THE PRIMARY METERING INSTALLATION.
3
DEC
DEM
DEP
DEF
2
0
X
VERSAVAC LOAD CONTROL
1
5/1/15
REVISED
DANNA
BURLISON
ADCOCK
BY
CK'D
APPR.
08.12-04A
BILL OF MATERIALS
MACRO UNIT
CU
ITEM
NO.
1
COMPATIBLE
UNIT
QTY
REQ'D
ITEM
NUMBER
BKTLCVVACEPF
1
2
BKTFBFGPIN15138F
4
9220278631
013264
013346
152107
9220087868
QTY
PER
CU
1
2
2
2
1
3
ISSTUDBOLT5814F
8
4
5
6
IPIN25PF
TTIEF500COVALPF
RCRISER40ALF
4
4
6
7
SW156BYPF
3
8
9
10
AREQSC120F
SWOSCADACNTKITF
FUSESEC30F
1
1
1
013264
072368
9220091018
9220068094
202111
260123
013264
013308
152107
010928
013128
013407
012277
220139
263165
230464
1
1
1
5
8
1
2
2
2
8
8
16
8
1
1
1
SWOVLRFRMFM
DESCRIPTION
BRACKET, VERSAVAC, 3PH TY 3H E-P
WASHER, LOCK, 5/8 IN, STEEL, GLV, SPRING, DOUBLE COIL, F
WASHER,3", SQUARE, CURVED, 13/16", HOLE
BOLT, MACH, SQ, NUT, 5/8" X 12"
BRACKET, FIBERGLASS STAND-OFF, 1-3/8" THREAD
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
STUD, LINE POST, 5/8" X 14"
INSULATOR, 25 KV POLYMER, 1-3/8" THREAD
PLASTIC TIE WRAP FOR 2-7/8" F-NECK INSULATOR
CABLE, XLP UG AL 4/0
SWITCH, BY-PASS, 3-SLD BLADE DISC, 15KV, LBK HOOKS, 600A
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
WASHER, SQUARE, 2-1/4", FLAT, 13/16", HOLE, GALV.
BOLT, MACH, SQ, NUT, 5/8" X 12"
BOLT, MACHINE, STAINLESS, STEEL, HEX, HEAD, 1/2" X 2"
WASHER, ROUND, BELLEVILLE SPRING, FOR 1/2" BOLT
WASHER, ROUND, STAINLESS STEEL, 304 ALLOY, FOR 1/2" BOLT
NUT, HEX, 1/2 IN, A304, STAINLESS STEEL, COARSE, THREAD, 1
ARRESTER, LIGHTNING, SEC 120-240 3 WIRE*
RISER, KIT-SCADA CONTROL
FUSE, SEC INS 30 AMP
VERSAVAC SWITCH USED FOR LOAD CONTROL - SWITCH AND CONTROL CABLE
11
SW152VVACF
1
12
13
AREQOH10F
KHLC40N6F
6
6
-
SW154VLRF
SWOHASTCNTLAKF
1
1
-
9220278629
264219
192281
0011060100
470114
220202
9220184790
1
1
30
5
6
1
1
SWITCH, VACUUM, 15KV 200A
CABLE, IS1 VLR SW CNTRL 35
CABLE, CONTROL, #10, 2 - CONDUCTOR
WIRE, TIE, #4 ALUMINUM, SLD
GUARD, TRANSFORMER, WILDLIFE, ROUND, GRAY MIN. 9"
ARRESTER, LIGHTNING, 10KV, HD MOV
CLAMP, HOT LINE, ALUM, SMALL, 4/0
VLR SWITCH - FOR REMOVAL ONLY
-
263138
263136
1
1
SWITCH, OH, 15KV, 400A, COOPER VLR, LD BRK
SWITCH, OH, 15KV, 400A, COOPER VLR, W/FAULT BLOCK, LD BRK
NOTES:
1. SEE DWG. 08.12-04A FOR DESIGN SPECIFICATIONS.
3
DEC
DEM
DEP
DEF
2
1
12/2/15
LOOSIER
BURLISON
ADCOCK
0
5/1/15
DANNA
BURLISON
ADCOCK
BY
CK'D
APPR.
REVISED
X
VERSAVAC LOAD CONTROL
08.12-04B
N
SECONDARY
SERVICE
120V
VLR
SWITCH
SECONDARY ARRESTER
SECONDARY INDICATING FUSE
TERMINAL STRIP IN VLR
SWITCH CONTROL CABINET
WHITE
TWO WIRE
CABLE
4
BLACK
3
BLACK
RED
G 2
WHITE
1
GREEN
0
6 PIN
PLUG
120V
N
GREEN
RED
GREEN
1
FOUR
WIRE
CABLE
WHITE
WHITE
G
RED
2
BLACK
BLACK
3
TERMINAL STRIP IN
RADIO SWITCH
ALTERNATE CONSTRUCTION
TERMINAL
WIRE
FUNCTION
120V
BLACK
120V FROM SOURCE
N
WHITE
NEUTRAL FROM SOURCE
1
GREEN
POWER TO SWITCH
G
WHITE
NEUTRAL TO SWITCH
2
RED
3
BLACK
CLOSE
TIP
3
DEC
2
DEM
DEP
DEF
CONNECTION DIAGRAM FOR
X
1
0
5/1/15
REVISED
DANNA
BURLISON
ADCOCK
BY
CK'D
APPR.
VERSAVAC SWITCH
08.12-04C
9"
5"
4
4"
5"
CL BOLT HOLE
(TYP.)
40"
1
117-7/8"
40"
10
72"
9
3
7
8
#6 SD BC
5
SIDE VIEW
2
NOTES:
1. SEE DWG. 08.12-06B FOR PLAN VIEW, NOTES AND
BILL OF MATERIALS.
48" MIN.
FRONT VIEW
3
DEC
2
DEM
DEP
DEF
LOAD CONTROL SWITCH
1
1/26/16
LOOSIER
BURLISON
ADCOCK
0
8/27/15
LOOSIER
BURLISON
ADCOCK
BY
CK'D
APPR.
REVISED
600 AMP
X
08.12-06A
9
10
4
1
PLAN VIEW
(CONTROL OPERATOR REMOVED FOR CLARITY)
BILL OF MATERIALS
MACRO UNIT
BUBBLE
NUMBER
-
COMPATIBLE
UNIT
ITEM
NUMBER
CU
QTY
1
SW2512ALDF
1
2
SWOHASTCNTLAKF
1
2
SWOHASTCNTLAF
1
3
4
-
-
5
CRIS1UGPVC10WF
15
6
7
8
CABGRP1X125F
WUSNGDPXRF
-
1
1
-
9
SW156SBDF
3
10
BKTSBDSWSTLF
3
9220270022
013264
13307
152107
9220269976
013264
13307
152107
9220279778
013264
13307
152107
152107
155331
014111
323421
320452
202107
010928
012277
013128
013407
152074
260136
013264
013308
070282
152107
ITEM
QTY/
CU
1
2
2
2
1
2
2
2
1
2
2
2
2
6
15
1
1
30
4
4
4
8
2
1
2
2
1
2
DESCRIPTION
SWITCH, OVERHEAD, 15KV 1200A, 3PH, ALDUTI-RUPTER, FBGLASS
WASHER, SPRING, COIL, STEEL, 5/8", BOLT, GALV
WASHER, 2-1/4",SQUARE,FLAT,11/16",HOLE
BOLT, MACHINE, SQ NUT, 5/8" X 12"
SWITCH, CONTROL, OPERATOR, ALDUTI-RUPTER SWITCH, KIRK KEY
WASHER, SPRING, COIL, STEEL, 5/8", BOLT, GALV
WASHER, 2-1/4",SQUARE,FLAT,11/16",HOLE
BOLT, MACHINE, SQ NUT, 5/8" X 12"
SWITCH, CONTROL, OPERATOR, ADULTI-RUPTER, W/O KIRK KEY
WASHER, SPRING, COIL, STEEL, 5/8", BOLT, GALV
WASHER, 2-1/4",SQUARE,FLAT,11/16",HOLE
BOLT, MACHINE, SQ NUT, 5/8" X 12"
BOLT, MACHINE, SQ NUT, 5/8" X 12"
LUG, COMPRESSION, 2H - 795 AL
SCREW, LAG, 1/2" X 2"
1" X 10 FT U GUARD
CABLE GRIP, SINGLE EYE
#6 DPX 600V SL CABLE
#6 CU GND
BOLT, MACHINE, STAINLESS, STEEL, HEX, HEAD,1 /2"X2"
NUT, HEX, 1/2 IN, A304, STAINLESS STEEL
WASHER, ROUND, BELLEVILLE SPRING, FOR 1/2" BOLT
WASHER, ROUND, FLAT, STAINLESS STEEL, 304, ALLOY, FOR,1/2"
BOLT, MACH, HEX, HD, 1/2"X2"
SWITCH, DISCONNECT, SOLID BLADE, 15KV, 600A, 1PH, SWITCH
WASHER, SPRING, COIL, STEEL, 5/8", BOLT, GALV
WASHER, SQUARE, 2-1/4", SQUARE, FLAT, 13/16
BRACKET, MNTG WD/CNCR POLE
BOLT, MACH, SQ, NUT, 5/8" X 12"
NOTES:
1. SEE DWG. 08.12-06A FOR DESIGN SPECIFICATIONS.
2. JUMPERS SHALL MATCH CONDUCTOR SIZE.
3. USE AS A LOAD CONTROL SWITCH WHERE A KIRK KEY SYSTEM IS IN PLACE.
4. PLACE SWITCH ON LOAD SIDE OF PRIMARY METERED CUSTOMERS.
5. FOR SWITCH OPERATOR WITHOUT KIRK KEY, USE ITEM # 9220279778 .
3
DEC
2
DEM
DEP
DEF
LOAD CONTROL SWITCH
1
12/2/15
LOOSIER
BURLISON
ADCOCK
0
8/27/15
LOOSIER
BURLISON
ADCOCK
BY
CK'D
APPR.
REVISED
600 AMP
X
08.12-06B
TAP CUSTOMER
TO THIS POLE
120/208V
120/208V
PRIMARY
400A VLR SWITCH
SW
CT
CT
N
SECONDARY
SW
PT
PT
TYPE
"S"
CONTROL
AN OVERHEAD AUTOMATIC TRANSFER SCHEME IS SHOWN IN THE ABOVE DRAWING. A MINIMUM OF FIVE POLES
ARE REQUIRED FOR THE INSTALLATION. THE TWO OUTSIDE POLES EACH HAVE A THREE-PHASE WYE-WYE
120/208V TRANSFORMER STATION. THESE STATIONS ARE CONSTRUCTED WITH SMALL KVA TRANSFERS AND
ARE CONNECTED TO A SMALL QUADRUPLEX CABLE WHICH RUNS TO THE NEUTRAL POSITION OF THE POLE WITH
THE TYPE "S" AUTOMATIC TRANSFER CONTROL. THE QUADRUPLEX CABLE IS OPENED AT THIS POLE AND SPLICED
TO THE TWO 45' PT CABLES WHICH CONNECT TO THE TYPE "S" CONTROL. THE 45' CT AND 45' SW CABLES ARE
CONNECTED TO THE 400A VLR SWITCH ON THE SAME POLE AS THE TYPE "S" CONTROL. THE 200' CT AND THE
200' SW CABLE ARE INSTALLED UP THE POLE WITH THE TYPE "S" CONTROL AND THEN LASHED TO THE
QUADRUPLEX CABLE GOING TO THE OTHER 400A VLR SWITCH. THE LOAD IS CONNECTED TO THE CIRCUIT
BETWEEN THE TWO VLR SWITCHES. THE TRANSFER SWITCHES WILL MAKE AN OPEN TRANSFER (OPEN & THEN
CLOSE) UPON LOSS OF ONE OR MORE PHASE VOLTAGES (THREE-PHASE SENSING) ON THE PREFERRED SOURCE
PROVIDED THE FAULT IS NOT ON THE TRANSFERRED CIRCUIT (FAULT BLOCK FEATURE). EITHER SOURCE CAN BE
CHOSEN AS THE PREFERRED SOURCE FROM THE CONTROL SELECTIONS. THE RETRANSFER TIME AND OPEN OR
CLOSE TRANSITION IS SELECTABLE. IT IS ALSO POSSIBLE TO SELECT NO PREFERRED SOURCE IN WHICH CASE
NO RETRANSFER OCCURS.
3
2
OVERHEAD AUTOMATIC TRANSFER SCHEME
1
0
8/25/10
REVISED
R
HOFFMAN
GUINN
ELKINS
DWG.
BY
CK'D
APPR.
08.13-01
LAMP TEST SWITCH (S6)
LATCH RELAY STATUS
TEST TERMINALS (T-1, T-2,
T-3)
SWITCH I OPEN AND
CLOSED LAMPS
SWITCH II OPEN AND
CLOSED LAMPS
PREFERRED-TOALTERNATE TIMER
ALTERNATE-TOPREFERRED TIMER
OPERATION SELECTOR
SWITCH (S3)
SOURCE I ENERGIZED
LAMP
SOURCE II ENERGIZED
LAMP
MANUAL OPERATION
SOURCE I AND SOURCE II
SWITCHES (S1, S2)
SOURCE-PREFERENCE
AND RETURN MODE
SELECTOR SWITCH (S4)
CONTROL MODE SWITCH (S5)
LOCKING TAB
FUSES
STOP SCREW
INSTRUCTION TAG
16"
8"
12-13/16"
(2) MTG HOLES FOR
5/8" MAX BOLT DIA.
1-1/2"
20-1/8"
22-5/32"
17-7/8"
5/8" HOLE PROVIDED
FOR CUSTOMER LOCK
GROUNDING TERMINAL LUG
(14 TO 4 STRANDED)
11"
13-1/2"
2-1/2" 2-1/2"
2-1/2" 2-1/2"
3"
STD CONTROL
5-1/4"
CONTROL WITH FAULT BLOCK
3
2
VLR TYPE S TRANSFER CONTROL
1
0
9/7/10
REVISED
R
GUINN
GUINN
ELKINS
DWG.
BY
CK'D
APPR.
08.13-03
5"
6"
24"
48"
24"
6"
48"
35"
#6 SD BC
72"
#6 SD BC
#2 SD BC
120/208V
PT SOURCE I
120/208V
PT SOURCE II
LASH 200' CT & SW
CABLE TO AERIAL
QUADRUPLEX
(COIL EXCESS)
#6 SD BC
SEE DETAIL 'A'
48" MIN.
48" MIN.
FRONT VIEW
SIDE VIEW
SOURCE II
SOURCE I
CT
PT
SW
SW
PT
CT
DETAIL "A"
NOTES:
1. SEE DWG. 08.13-01 FOR OVERVIEW OF ENTIRE OVERHEAD AUTOMATIC TRANSFER SCHEME.
2. SEE DWG. 08.12-02B FOR BILL OF MATERIALS.
3. BOND TANK AND FRAME WITH #2 SD BC TO SYSTEM NEUTRAL.
4. THE OTHER POLE IN TRANSFER SCHEME WILL BE IDENTICAL, EXCEPT NO S TRANSFER CONTROL.
3
AUTOMATIC TRANSFER SWITCH ASSEMBLY, (VLR),
2
R
1
0
11/29/10
REVISED
GUINN
GUINN
ELKINS
BY
CK'D
APPR.
CONTROL WIRING DETAIL
DWG.
08.13-05
SOURCE
LOAD
5"
11"
10"
42"
10"
9 13 14
64"
42"
1
4"
SEE NOTE 1
2
35"
72"
#2 SD BC
11
12
12"
31'-8" MAX.
FOR CONTROL
CABLE
4
#6 SD BC
19
30"
4' ABOVE
GROUND
FRONT VIEW
SIDE VIEW
(LOOKING FROM LOAD SIDE)
NOTES:
1. ROTATE B PHASE STANDOFF AS NECESSARY TO CLEAR THE CONTROL BOX.
2. SEE DWG. 08.13-08B FOR PLAN VIEW.
3. SEE DWG. 08.13-08C FOR BILL OF MATERIALS.
3
2
SCADA MATE CX SWITCH
1
5/24/13
0
11/29/10
REVISED
DANNA
ADCOCK
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
STANDARD MOUNTING ARRANGEMENT
DWG.
08.13-08A
34-3/8"
23-1/16"
SOURCE
LOAD
3
8
15
PLAN VIEW
NOTES:
1. SEE DWG. 08.13-08A FOR DESIGN SPECIFICATIONS.
2. SEE DWG. 08.13-08C FOR BILL OF MATERIALS.
3
2
SCADA MATE CX SWITCH
1
5/24/13
0
11/29/10
REVISED
DANNA
ADCOCK
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
STANDARD MOUNTING ARRANGEMENT
DWG.
08.13-08B
BILL OF MATERIALS
CU
ITEM
NO
MACRO UNIT
-
COMPATIBLE
UNIT
QTY
REQ'D
1
SW15S6VRTSATSF
(SEE NOTE 1)
1
1
SW15S9VRTSATSF
(SEE NOTE 1)
1
2
SW156BYPF
3
3
AREQOH10F
6
4
CRIS1UGPVC225CF
2
5
AREQSC120F
1
6
KLC2H79ALF
12
7
KLC4H79ALF
6
8
9
10
KHLC7933F
TTIEF795ALF
WOCN6CU1CF
6
6
6
11
SWOSANTKITF
1
12
SWOSANTBRKF
1
13
BKTFPIS20F
3
14
15
IHPTT15F
IDES25PF
3
12
16
ISEYEBOLT5810F
6
17
18
DECLMP795AACF
WOP795AACF
6
60
19
SWOS5201CTRF
1
CATALOG
NUMBER
013265
013308
152122
9220179952
013264
152107
152123
011708
013128
013407
152122
266178
013265
013308
013264
152107
152123
011708
013128
013407
152122
013264
013308
152107
260123
220202
323422
434122
434142
220139
010928
012277
013163
155331
10542504
010928
012277
013163
155464
10542504
9220184794
121418
190204
9220109491
390122
402179
013264
013308
152106
240306
013264
013346
070430
072361
152107
080212
080577
011708
013346
101125
200238
9220109490
013264
013308
152107
QTY
PER
CU
2
46
2
1
21
15
2
3
1
1
2
1
2
46
21
15
2
3
1
1
2
2
2
2
1
1
1
0.2
3
1
2
2
4
1
2
2
2
4
1
2
1
1
1
1
1
1
2
2
2
1
2
2
1
1
2
1
1
1
1
1
1
1
1
1
2
DESCRIPTION
WASHER, SPRING, COIL, STEEL, FOR 3/4" BOLT
WASHER, SQUARE, 2-1/4", FLAT, 13/16" HOLE, GALV.
BOLT, SQUAREHEAD, 3/4 IN, 12 IN, S, A307, GLV, 10, UNC
SWITCH, VRT, AUTO, 14.4KV, 630A, SCADA-MATE CX
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
BOLT, MACH, SQ, NUT, 5/8"X12"
BOLT, SQUAREHEAD, 3/4 IN, 14 IN, S, A307, GALV., 10, UNC
BOLT, 5/8 IN, 10 IN, STEEL, GALV., OVAL EYE
WASHER, ROUND, BELLEVILLE SPRING, FOR 1/2" BOLT
WASHER, ROUND, FLAT, STAINLESS STEEL, 304, ALLOY, FOR 1/2"
BOLT, SQUAREHEAD, 3/4 IN, 12 IN, S, A307, GLV, 10, UNC
SWITCH, SCADAMATE UPRIGHT MTG
WASHER, SPRING, COIL, STEEL, FOR 3/4" BOLT
WASHER, SQUARE, 2-1/4", FLAT, 13/16" HOLE, GALV.
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
BOLT, MACH, SQ, NUT, 5/8"X12"
BOLT, SQUAREHEAD, 3/4 IN, 14 IN, S, A307, GLAV., 10, UNC
BOLT, EYE, 5/8 IN, 10 IN, STEEL, GALV., OVAL EYE
WASHER, ROUND, BELLEVILLE SPRING, FOR 1/2" BOLT
WASHER, ROUND, FLAT, STAINLESS STEEL, 304, ALLOY, FOR 1/2"
BOLT, SQUAREHEAD, 3/4 IN, 12 IN, S, A307, GLV, 10, UNC
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
WASHER, SQUARE, 2-1/4", SQUARE, FLAT, 13/16" HOLE, GALV.
BOLT, MACH, SQ, NUT, 5/8"X12"
SWITCH, BY-PASS, SWITCH, BYPASS, 3-SLD BLADE DISC, 15KV, LBK H
ARRESTER, LIGHTNING, 10KV HD MOV W/SILICONE RUBBER POLY
GUARD, PVC, CABLE, 2-1/4"X10'
BANDING, STAINLESS STEEL, 316, SS, 3/4", WIDE, .030, TH
BANDING, BUCKLE, SS, 3/4", FOR BANDING
ARRESTER, LIGHTNING, SEC 120-240 3 WIRE
BOLT, MACHINE, STAINLESS STEEL, HEX HEAD, 1/2"X2"
NUT, 1/2 IN, A304, STAINLESS STEEL, HEX HEAD
WASHER, FLAT, ROUND, SILICON, BRONZE, FOR 1/2" BOLT
LUG, COMP 2H-795AL
WASHER, ROUND, RD, 1/2, SS, 1.375" OD
BOLT, MACHINE, STAINLESS STEEL, HEX HEAD, 1/2"X2"
NUT, HEX, 1/2 IN, A304, STAINLESS STEEL
WASHER, FLAT, ROUND, SILICON, BRONZE, FOR 1/2" BOLT
LUG, COMP 4HOLE 795 AAC
WASHER, ROUND, 1/2, SS, 1.375" OD
CLAMP, HOT LINE, ALUMINUM, EXTRA LARGE 795
TIE, TOP F NECK 795 AL
WIRE, COPPER, #6, HARD DRAWN, BR
KIT, ANTENNA, UTILI-NET
TAPE, ELECTRICAL, ELEC, 3/4X66'X.007
COMPOUND, INSUL, SEAL, PAD, 3-3/4"
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
WASHER, SQUARE, 2-1/4", FLAT, 13/16" HOLE, GALV.
BOLT, MACHINE, 5/8 IN, 10 IN, STEEL, A-ASTM A307, GALV., MACH,
BRACKET, STREET LIGHT, 6 ',W/30", RISE, GALV-STL
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
WASHER, 3", SQUARE, CURVED, 13/16" HOLE
BRACKET, FIBERGLASS, STAND-OFF, 20"
STUD, LINE POST, 5/8"X1-3/4", INSULATOR STUD
BOLT, MACH, SQ, NUT, 5/8"X12"
INSULATOR, POST, TIE, TOP, 15/25KV, WITHOUT STUD
INSULATOR, DEADEND, POLYMER, 25KV, SILICONE, RATED 15K
BOLT, EYE, 5/8 IN, 10 IN, STEEL, GALV, OVAL EYE
WASHER, 3", SQUARE, CURVED, 13/16",HOLE
CLAMP, DE, SO, 336.4-954 ACSR, 397.5-1000 AL, COND RANGE
WIRE, AAC, AAC 37STR 795 66 REE
SWITCH, CTRL, AUTOMATED, INTELLI-TEAM-II
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
WASHER, SQUARE, 2-1/4", FLAT, 13/16" HOLE, GALV.
BOLT, MACH, SQ, NUT, 5/8"X12"
NOTES:
1. CHOOSE EITHER THE 900A OR 600A SCADA-MATE VERTICAL LOAD BREAK SWITCH.
2. SEE DWGS. 08.13-08A AND 08.13-08B FOR DESIGN SPECIFICATIONS.
3
2
SCADA MATE CX SWITCH
1
5/24/13
0
11/29/10
REVISED
DANNA
ADCOCK
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
STANDARD MOUNTING ARRANGEMENT
DWG.
08.13-08C
NOTES:
1. TO EXTEND BATTERY CARRYOVER TIME, THE SWITCH TURNS OFF POWER TO THE LEDS AND LCD ON THE FACEPLATE WHEN THE
CONTROL CABINET DOOR IS CLOSED.
LEDS
OVERCURRENT FAULT - COMES ON WHEN A, B OR C PHASE HAS AN OVERCURRENT CONDITION.
A. IF OMNI-RUPTER IS CLOSED, LED TURNS OFF WHEN THREE-PHASE LINE VOLTAGE IS SENSED AND AFTER 45 MINUTES.
B. IF OMNI-RUPTER SWITCH IS OPEN, LED TURNS OFF WHEN THE SWITCH IS CLOSED AND REMOTE/LOCAL IS TOGGLED MANUALLY
OR VIA SCADA.
C. IF OMNI-RUPTER SWITCH IS NORMALLY OPEN, LED TURNS OFF WHEN REMOTE/LOCAL IS TOGGLED MANUALLY OR VIA SCADA OR
WHEN THE SWITCH IS CLOSED.
REMOTE COMMUNICATIONS RCV/XMIT - BLINK WHEN COMMUNICATION SIGNALS ARE RECEIVED OR SENT.
ERROR DETECTED - COMES ON FOR ANY OF THE FOLLOWING CONDITIONS:
A. BATTERY CHARGER OVER-VOLTAGE.
B. OPEN/CLOSE CONTACTS ARE BOTH OPEN OR BOTH CLOSED.
C. TEMPERATURE SENSOR FAILURE.
D. SWITCH ERROR SUCH AS BYPASS SWITCHES OPEN AND OMNI-RUPTER SWITCH IS BYPASSED.
PROCESSOR STATUS - BLINKS ONCE PER SECOND WHEN CONTROL HAS POWER AND SOFTWARE IS RUNNING NORMALLY.
BATTERY LOW - OFF WHEN BATTERY CHARGER WORKING NORMAL. ON WHEN BATTERY VOLTAGE DROPS BELOW A PRESET LIMIT. IF
ON WITH AC POWER ON TO CONTROL, BATTERY MAY BE DEFECTIVE. BLINKS DURING ANY BATTERY TEST.
3
2
OMNI-RUPTER SWITCH
R
1
0
8/11/10
REVISED
GUINN
GUINN
ELKINS
BY
CK'D
APPR.
CONTROL FACEPLATE
DWG.
08.13-10D
AREA MUST BE
WATERPROOF
COAX CONNECTION
HOW TO WATERPROOF THE ANTENNA COAX CONNECTION:
1. SCREW THE ANTENNA COAX CONNECTOR TOGETHER SO THAT IT IS TIGHT.
2. WRAP ELECTRICAL TAPE AROUND THE COAX CONNECTOR COVERING ONE INCH EITHER SIDE OF THE
CONNECTION.
3. PLACE THE AQUA SEAL PAD ( CN 402179) SQUARELY OVER THE COAX CONNECTION AND WRAP IT SECURELY
AROUND TO WATERPROOF THE CONNECTION.
4. WRAP ELECTRICAL TAPE AROUND THE AQUA SEAL WATERPROOFING PAD TO COVER THE ENTIRE AREA OF AQUA
SEAL PLUS ONE INCH ABOVE AND BELOW THE SEAL.
NOTES:
1. SEE DWG. 08.13-10A FOR DESIGN SPECIFICATIONS.
2. SEE DWG. 08.13-10C FOR BILL OF MATERIALS.
3
2
ANTENNA INSTALLATION
R
1
0
11/29/10
REVISED
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
FOR VERTICAL OMNI-RUPTER SWITCH
DWG.
08.13-10E
TANGENT TO DEADEND
5"
12"
2"
4" TYP.
18"
#6 SD BC
36"
#2 SD BC
2"
18"
#2 SD BC
TANK GROUND
TO SYSTEM
NEUTRAL
36"
2"
AT
TA
C
HM
EN
T
18"
GU
Y
72"
#2 SD BC
NEUTRAL
#6 SD BC
FRONT VIEW
4"
SIDE VIEW
DEADEND TO DEADEND
2"
18"
36"
2"
4"
#6 SD BC
#2 SD BC
TANK GROUND TO
SYSTEM NEUTRAL
2"
18"
36"
2"
18"
4"
2"
72"
2"
4"
#2 SD BC
#6 SD BC
FRONT VIEW
SIDE VIEW
NOTES:
1. SEE SECTION 01 FOR ADDITIONAL GROUNDING DETAILS.
3
2
1
0
10/13/10
REVISED
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
VERTICAL CONSTRUCTION TO
VERTICAL CONSTRUCTION
WITH OIL SECTIONALIZER (FMO)
R
DWG.
08.04-06
1
8"
3
2
#6 SD BC
30"
#6 SD BC
NEUTRAL
#6 SD BC
FRONT VIEW
SIDE VIEW
BILL OF MATERIALS
MACRO UNIT
-
CU
ITEM
NO.
COMPATIBLE
UNIT
QTY
REQ'D
1
AREQOH10F
2
2
3
SECT_
BKTCOLASTLXARMF
1
2
CATALOG
NUMBER
220202
193511
070101
QTY
PER
CU
1
2
1
1
DESCRIPTION
ARRESTER, LIGHTNING, 10KV HD MOV W/SILICONE
CABLE, 600V #6 SOLID SD CU
SECTIONALIZER
BRACKET, LA AND CO TY A
NOTES:
1. SEE SECTION 01 FOR ADDITIONAL GROUNDING DETAILS.
2. ARRESTERS TO BE MOUNTED ON SOURCE AND LOAD SIDE.
3
SECTIONALIZER ASSEMBLY,
2
R
1
O
10/13/10
REVISED
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
OIL TYPE, VERTICAL (FMO)
DWG.
08.04-08
DEADEND TO DEADEND
9"
14"
34"
16"
23"
LOAD
2"
#2 SD BC
2"
6"
10"
24"
6"
#2 SD BC
10"
20"
6"
10"
72"
#2 SD BC
#6 SD BC
SIDE VIEW
FRONT VIEW
TANGENT TO DEADEND
SOURCE
10"
4"
16"
4"
4"
LOAD
#6 SD BC
8"
BOND CASE GROUND
WITH CONNECTOR
SUPPLIED ON BRACKET
6"
12"
12"
18"
12"
22"
6"
14"
72"
#2 SD BC
#2 SD BC
4"
#6 SD BC
SIDE VIEW
FRONT VIEW
NOTES:
1. SEE SECTION 01 FOR ADDITIONAL GROUNDING DETAILS.
2. RUN #2 SD BC UNDER CROSSARM TO B0ND SECTIONALIZERS TO SYSTEM NEUTRAL.
3
2
1
0
10/13/10
REVISED
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
HORIZONTAL CONSTRUCTION TO
HORIZONTAL CONSTRUCTION
WITH OIL SECTIONALIZER (FMO)
R
DWG.
08.04-12
SOURCE
LOAD
6"
1
4
24"
#2 WP COPPER
CU RCRISERN2CUF
3
33"
2
5
27"
#2 SD BC
SEE NOTE 3
NEUTRAL
FUSES
STORED WITH
BARRELS DOWN
ON 3" STAPLE
#6 SD BC
FRONT VIEW
SIDE VIEW
NOTES:
1. ISSUE RECLOSER SEPARATELY. RECLOSER WILL COME ARRESTERS PRE-MOUNTED.
2. SEE DWG. 08.01-11 FOR CUTOUT MOUNTING DETAILS
3. EQUIPMENT CASE GROUND TO NEUTRAL TO BE #2 SD BC.
4. SEE DWG. 08.05-17B FOR BILL OF MATERIALS AND DETAILS ON ALUMINUM CROSSARM.
5. FOR TWO-PHASE HORIZONTAL INSTALLATIONS, ONLY INSTALL RECLOSERS AND SWITCHES ON OUTSIDE TWO
PHASES.
3
1/6/16
LOOSIER
BURLISON
ADCOCK
2
11/17/15
LOOSIER
BURLISON
ADCOCK
1
8/7/14
SALAS
GUINN
ADCOCK
0
10/6/10
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
DEC
DEM
DEP
DEF
RECLOSER ASSEMBLY,
HORIZONTAL CONSTRUCTION (FMO)
X
08.05-17A
5
1
2
3
FRONT VIEW
BILL OF MATERIALS
CU
ITEM
NO.
MACRO UNIT
-
COMPATIBLE
UNIT
QTY
REQ'D
1
BKTCOLA8AALF
1
1
2
FUSE15CO100F
2
3
3
SW153COSBDF
4
6
4
5
KHLC40N6F
RCRISERN2CUF
4
2
6
3
ITEM
NUMBER
9220205263
10034908
10540102
10544005
221112
221112
269046
9220184790
193513
QTY
PER
CU
1
2
2
2
1
1
1
1
1
DESCRIPTION
BRACKET, CUTOUT, BYPASS CUTOUT, 9 POSITION, AL, 97-1/2"
BOLT, MCH, SQ, GLV, 5/8" X 12"
WASHER, SQ., RB, CRV, 3" X 3"
WASHER, LK, 5/8", COIL, DBL, GLV.
CUTOUT, LB, 15KV, 100A, 16KA, 110KV BIL
CUTOUT, LB, 15KV, 100A, 16KA, 110KV BIL
BLADE, SOLID, CUTOUT, 15KV, 300A
CLAMP, HOT LINE, ALUMINUM, SMALL
CABLE, 600V, #2 SD CU, 7 STR.
NOTES:
1. SEE DWG. 08.05-17A FOR DESIGN SPECIFICATIONS AND NOTES.
3
DEC
DEM
DEP
DEF
RECLOSER ASSEMBLY,
2
1
1/6/16
LOOSIER
BURLISON
ADCOCK
0
10/6/10
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
HORIZONTAL CONSTRUCTION (FMO)
X
08.05-17B
5"
10"
20"
18"
38"
10"
42"
60"
44"
12"
12"
#2 SD BC BOND
TANK AND FRAME
TO SYSTEM NEUTRAL
NEUTRAL
SECONDARY
#6 SD BC
12"
SECONDARY
#6 SD BC
FRONT VIEW
SIDE VIEW
NOTES:
1. CONTROL BOX AND SECONDARY REQUIRED FOR ELECTRONIC RECLOSER ONLY.
2. ISSUE RECLOSER AND ELECTRONIC CONTROL SEPARATELY.
3. RECLOSER MAY BE REVERSED IN HANGER TO ACCOMMODATE SOURCE AND LOAD POSITION.
4. SEE SECTION 01 FOR ADDITIONAL GROUNDING DETAILS.
3
RECLOSER ASSEMBLY, THREE-PHASE,
2
R
1
0
10/11/10
REVISED
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
HORIZONTAL, 600 AMP SWITCH (FMO)
DWG.
08.06-12
10"
20"
18"
38"
10"
55"
NEUTRAL
SEE NOTES 2 & 3
SIDE VIEW
FRONT VIEW
NOTES:
1. ENGINEER MUST SPECIFY JUMPER AND PRIMARY CONNECTOR SIZE.
2. REFER TO DWG. 08.12-01 FOR WIRING DIAGRAM.
3. RADIO SWITCH MUST BE SET FOR PURCHASE BY INSTALLING JUMPER PINS AS SPECIFIED IN CONTROL BOX.
3
2
1
0
11/29/10
REVISED
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
LOAD CONTROL SWITCH ASSEMBLY, (VLR),
THREE-PHASE
HORIZONTAL WITH 600 AMP BYPASS (FMO)
R
DWG.
08.12-06
LOAD
SOURCE
6
5"
6"
15
18-3/4"
43"
42"
11"
7
5"
26"
26"
41"
42"
14
5
26"
97"
97"
26"
6"
25
34"
21"
34"
SURGE
ARRESTER
MOUNTING
BRACKETS
2
29-1/8"
72"
3
1
LOCKOUT/TAGOUT
BRACKET FOR SWITCH
OPEN POSITION
4
MANUAL OPEN
PULL-RING
#2 SD BC
31'-8" MAX.
FOR CONTROL
CABLE
13
#6 SD BC
30"
9" MINIMUM
RADIUS ON CABLE
4' ABOVE
GROUND
#6 SD BC
FRONT VIEW
NOTES:
SIDE VIEW
(LOOKING FROM LOAD SIDE)
1. SEE DWG. 08.13-10B FOR PLAN VIEW AND BILL OF MATERIALS. SEE DWG. 08.13-10C FOR OPTIONAL CONSTRUCTION BILL OF
MATERIALS AND ADDITIONAL NOTES.
2. SEE DWG. 08.13-10D FOR CONTROL FACEPLATE.
3. SEE DWG. 08.13-10E FOR ANTENNA INSTALLATION.
4. ARRESTERS SHOULD BE INSTALLED ON MOUNTING PADS PROVIDED ON BOTH SIDES OF THE OMNI-RUPTER SWITCH. THE ARRESTER
SOURCE LEAD SHOULD BE CONNECTED TO THE 795 JUMPER JUST BEYOND THE OMNI-RUPTER 2-HOLE HIGH-VOLTAGE TERMINAL ON
EITHER SIDE OF THE OMN-RUPTER SWITCH TO KEEP THE LEADS AS SHORT AS POSSIBLE. THE GROUND LEAD SHOULD BE RUN FROM
THE GROUNDING CONNECTION ON THE ARRESTER INTERRUPTER TO THE OMNI-RUPTER SUPPORT FRAME. THIS LEAD MUST BE LONG
ENOUGH FOR THE INTERRUPTER TO OPERATE, BUT SHORT ENOUGH TO CLEAR ADJACENT CONDUCTORS. ALL
GROUND CONNECTIONS MUST BE VERY SECURE, ESPECIALLY THE #2 BC CONNECTION AT THE BASE OF THE
OMNI-RUPTER SWITCH.
3
2
DEC
8/5/14
1
5/24/13
0
11/29/10
REVISED
EANES
EANES
ADCOCK
DANNA
ADCOCK
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
DEM
DEP
DEF
OMNI-RUPTER SWITCH
STANDARD MOUNTING ARRANGEMENT (FMO)
X
08.13-10A
34-3/8"
23-1/16"
SOURCE
LOAD
2
5
15
6
25
7
14
PLAN VIEW
MACRO UNIT
CN/CU
ITEM
NO
1
QTY
REQ'D
CATALOG
NUMBER
-
1
2
-
1
3
-
1
4
-
1
5
-
6
6
-
6
7
8
9
10
-
-
11
-
6
12
-
12
13
-
3
14
-
3
15
-
3
16
17
18
-
3
1
35
6
19
20
21
22
23
24
25
BILL OF MATERIALS
QTY
PER
COMPATIBLE
UNIT
DESCRIPTION
9220109487
9220109490
CU
1
1
SW, VRT, AUTO, 14.4KV, 900A, 35' CONTROL CABLE
SW, CONTROL, AUTO, INTELLI-TM-II, WITH RADIO
013264
013308
152107
9220109491
390122
402179
013264
013308
152107
240306
220202
080577
011708
013308
013346
013264
101125
152123
152107
011708
155464
012277
013163
010928
10542504
155331
012277
013163
010928
10542504
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
6
2
15
3
1
4
8
4
4
1
2
4
2
2
WASHER, SPG, CO, S, FOR 5/8" BOLT
WASHER, 2-1/4", SQ, FLT, 13/16" HOLE
BOLT, MACHINE, 5/8" X 12"
KIT, ANTENNA, UTILI-NET, MA-30-AB RADIO
TAPE, ELECTRICAL, 3/4" X 66' X .007 MIL
COMPOUND, INSUL, SEAL, PAD, 3-3/4"
WASHER, SPG, CO, S, FOR 5/8" BOLT
WASHER, 2-1/4", SQ, FLT, 13/16" HOLE
BOLT, MACHINE, 5/8" X 12"
BRACKET, ST. LIGHT, 6', WITH 30" RISE, GALV. STEEL
ARRESTER, 10KV, HD-MOV, SILICONE/RUBBER/POLYMER
INSULATOR, 25KV, DEADEND, POLYMER
BOLT, OVAL EYE, 5/8" X 10"
WASHER, 2-1/4" SQUARE, FLAT, 13/16" HOLE
WASHER, 3" SQUARE, CURVED, 13/16" HOLE
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT
CLAMP, DE, SO, 336-1000 AL
BOLT, MACHINE, 3/4" X 14"
BOLT, MACHINE, 5/8" X 12"
BOLT, OVAL EYE, 5/8" X 10"
LUG, COMPR, 795 AAC, 4-HOLE (BOTTOM OF PKR SW)
NUT, SS, HEX, COARSE THREAD
WASHER, FLAT, ROUND, SILICON, BRONZE, FOR 1/2" BOLT
BOLT, MACHINE, SS, HEX, HEAD, 1/2" X 2"
WASHER, RD, 1/2", SS, 1-3/8" OD
LUG, COMPR, 795 AL, 2-HOLE
NUT, SS, HEX, COARSE THREAD
WASHER, FLAT, ROUND, SILICON, BRONZE, FOR 1/2" BOLT
BOLT, MACHINE, SS, HEX, HEAD, 1/2" X 2"
WASHER, RD, 1/2", SS, 1-3/8" OD
323422
434122
434142
260123
152107
013308
013264
080212
072361
070430
014114
152107
013264
190204
121418
220139
190204
190312
013308
013264
013128
013407
9220184794
1
0.2
3
1
2
2
2
1
1
1
1
1
GUARD, CABLE, PVC 2-1/4" X 10'
BANDING, 316, SS, 3/4" WIDE, .030 THICKNESS, 100', RL
BANDING, BUCKLE, SS, 3/4",FOR BANDING
SWITCH, 600 AMP BYPASS TYPE
BOLT, MACH, SQ, NUT, 5/8" X 12"
WASHER, SQUARE, 2-1/4", FLAT, 13/16", HOLE, GALV.
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
INSULATOR, POST, TIE-TOP, 15/25KV, W/O STUD
STUD, LINE POST, 5/8" X 1-3/4"
BRACKET, FIBERGLASS, STAND-OFF, 20"
SCREW, LAG, 1/2" X 4"
BOLT, MACHINE, SQ, NUT, 5/8" X 12"
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT
#6 BC, HDW
TIE, PF, TOP F NECK 795 AL
ARRESTER-SECONDARY, 120/240 3-WIRE
WIRE, CU, BR, HRD, DRN, #6 (FOR ARRESTER GND)
WIRE, #2 CU, BR, SDW, 7, STR, #2 (FOR POLE GND)
WASHER, SQUARE FLAT, 5/8"
WASHER, SPRING COIL, FOR 5/8"
WASHER, SPRING, BELLEVILLE
WASHER, STAINLESS STEEL, ROUND, FLAT, 1/2"
HLC, 336 TO 795
1
1
6
1
2.4
1
42
21
1
1
1
NOTES:
1. SEE DWG. 08.13-10A FOR DESIGN SPECIFICATIONS AND DWG. 08.13-10C FOR OPTIONAL OPERATION/
INSTALLATION BILL OF MATERIALS AND ADDITIONAL NOTES.
3
2
OMNI-RUPTER SWITCH
1
5/24/13
0
11/29/10
REVISED
DANNA
ADCOCK
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
STANDARD MOUNTING ARRANGEMENT (FMO)
DWG.
08.13-10B
MATERIALS NEEDED FOR
OPTIONAL OPERATION/INSTALLATION
MACRO UNIT
CU
ITEM
NO.
COMPATIBLE
UNIT
QTY
REQ'D
CATALOG
NUMBER
QTY
PER
CU
1
-
1
9220109493
1
2
-
1
9220109494
1
12
010928
012277
013163
10542504
155408
2
2
4
2
1
1
2
4
2
2
1
4
8
4
4
1
4
8
4
4
1
1
1
1
1
1
1
1
1
3
-
-
4
-
12
5
-
6
6
-
6
7
8
-
6
1
9
-
1
10
11
-
1
1
155331
012277
013163
010928
10542504
155457
012277
013163
010928
10542504
155464
012277
013163
010928
10542504
9220184794
012210
011708
013264
013308
013346
080577
101119
101125
DESCRIPTION
RADIO, REPLACEMENT, UTILI-NET, SERIES II WANGATE RADIO
FOR MOUNTING INSIDE CONTROL PANEL
RADIO, REPEATER/RELAY, UTILI-NET, WANGATE, AC/DC,
WEATHERIZED, SELF-CONTAINED
BOLT, MACHINE, SS, HX, HD, 1/2" X 2"
NUT, SS, HX, 304 ALLOY, COARSE, THREAD, 1/2"
WASHER, FLT, RD SIL, BRN, FOR 1/2" BOLT
WASHER, RD, 1/2", SS, 1-3/8" O.D.
LUG, COMP 2H 336 AAC
LUG, COMP 2H-795AL
NUT, SS, HEX, COARSE THREAD
WASHER, FLAT, ROUND, SILICONE, BRONZE, FOR 1/2" BOLT
BOLT, MACHINE, SS, HEX HEAD, 1/2" X 2"
WASHER, RD, 1/2", SS, 1-3/8" OD
LUG, COMP, 4 HOLE, 336.4 AAC
NUT, SS, HX, 304 ALLOY, COARSE, THREAD, 1/2"
WASHER, FLT, RD SIL, BRN, FOR 1/2" BOLT
BOLT, MACHINE, SS, HX, HD, 1/2" X 2"
WASHER, RD, FLT, SS, 304 ALLOY, FOR 1/2" BOLT
LUG, COMP, 4 HOLE, 795 AAC
NUT, SS, HX, 304 ALLOY, COARSE, THREAD, 1/2"
WASHER, FLT, RD SIL, BRN, FOR 1/2" BOLT
BOLT, MACHINE, SS, HX, HD, 1/2" X 2"
WASHER, RD, FLT, SS, 304 ALLOY, FOR 1/2" BOLT
HLC, 336 TO 795
NUT, OVAL EYE, 5/8"
BOLT, OVAL EYE, 5/8" X 10"
WASHER, SPG, CO, S, FOR, 5/8" BOLT
WASHER, 2-1/4", SQ, FLT, 13/16" HOLE
WASHER, 3", SQ, CRV, 13/16" HOLE
INSULATOR, POLYMER, 25KV, DEADEND, SILICONE, RATED 15K
CLAMP, DE, SO, 2/0-556.5 ACSR, 2/0-556.5 AL, COND RANG
CLAMP, DE, SO, 336.4-954 ACSR, 397.5-1000 AL, COND RANG
NOTES:
1. SEE DWG. 08.13-10A FOR DESIGN SPECIFICATIONS AND DWG. 08.13-10B FOR PLAN VIEW.
2. SEE DWG. 08.13-10D FOR CONTROL FACEPLATE AND DWG. 08.13-10E FOR ANTENNA CONSTRUCTION.
3. REPLACEMENT BATTERY FOR THE INTELLITEAM CONTROL IS CN 9220176380 . THESE ARE NOT KEPT IN STORES
DUE TO SHELF LIFE. CONTACT PURCHASING FOR ORDERING AND LEAD TIME.
4. SEE DWG. 08.13-10D FOR CONTROL FACEPLATE AND DWG. 08.13-10E FOR ANTENNA INSTALLATION.
5. BLADE CONTACTS ARE GREASELESS AND SELF-LUBRICATING SO NO GREASE IS NEEDED.
6. SHORTING BLOCKS FOR SENSOR SECONDARIES ARE SHIPPED INSTALLED IN SWITCH CONNECTOR. REMOVE
AND SAVE SHORTING BLOCKS TO ALLOW SENSOR CABLE CONNECTION.
7. IF OPERATING SPRING IS CHARGED, ONLY A SINGLE PULL ON THE MOTOR OPERATOR PULL-RING IS REQUIRED.
IF POWER IS LOST AND THE OPERATING SPRING IS FULLY DISCHARGED, USE A HOOK STICK TO PULL ON THE
THE PULL-RING 7 TO 9 TIMES TO EFFECT A CHANGE OF STATE.
8. THE VT AND CT SENSORS SHOULD ALWAYS BE ORIENTED TOWARD THE SOURCE SIDE OF THE SWITCH.
3
2
OMNI-RUPTER SWITCH
R
1
0
11/29/10
REVISED
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
STANDARD MOUNTING ARRANGEMENT (FMO)
DWG.
08.13-10C
ONE-LINE
5"
SUB
FDR1
NOTE: IF YOU NEED AUTOMATED
OMNI-RUPTER IN FDR2,
FDR1 MUST BE RAISED
TO POSITION OF DOTTED
STACKED TOP CIRCUIT.
FDR2
AOR
36"
19
LOAD
SOURCE
6
36"
19
6"
25-1/4"
6"
14
18-3/4"
43"
42"
11"
19
7
5"
#6 SD BC
26"
26"
41"
42"
13
5
26"
#2 SD BC
97"
97"
26"
6"
MANUAL OPEN
PULL-RING
LOCKOUT/TAGOUT
BRACKET FOR SWITCH
OPEN POSITION
34"
21"
34"
SURGE
ARRESTER
MOUNTING
BRACKETS
2
29-1/8"
60"
3
#2 SD BC
1
4
#2 SD BC
#2 SD BC
#6 SD BC
12
#6 SD BC
FRONT VIEW
SIDE VIEW
(LOOKING FROM LOAD SIDE)
NOTES:
1. SEE DWG. 08.13-11B FOR PLAN VIEW AND BILL OF MATERIALS. SEE DWG. 08.13-10A FOR OMNI-RUPTER CONTROLLER.
2. SEE DWG. 08.13-10D FOR CONTROL FACEPLATE.
3. SEE DWG. 08.13-10E FOR ANTENNA INSTALLATION.
4. ARRESTERS SHOULD BE INSTALLED ON MOUNTING PADS PROVIDED ON BOTH SIDES OF THE OMNI-RUPTER SWITCH. THE ARRESTER
SOURCE LEAD SHOULD BE CONNECTED TO THE 795 JUMPER JUST BEYOND THE OMNI-RUPTER 2-HOLE HIGH-VOLTAGE TERMINAL ON
EITHER SIDE OF THE OMN-RUPTER SWITCH TO KEEP THE LEADS AS SHORT AS POSSIBLE. THE GROUND LEAD SHOULD BE RUN FROM
THE GROUNDING CONNECTION ON THE ARRESTER INTERRUPTER TO THE OMNI-RUPTER SUPPORT FRAME. THIS LEAD MUST BE LONG
ENOUGH FOR THE INTERRUPTER TO OPERATE, BUT SHORT ENOUGH TO CLEAR ADJACENT CONDUCTORS. ALL GROUND CONNECTIONS
MUST BE VERY SECURE, ESPECIALLY THE #2 BC CONNECTION AT THE BASE OF THE OMNI-RUPTER SWITCH.
3
DEC
2
8/5/14
1
5/24/13
0
4/22/10
REVISED
EANES
EANES
ADCOCK
DANNA
ADCOCK
GUINN
GUINN
ELKINS
BY
CK'D
APPR.
DEM
DEP
DEF
OMNI-RUPTER SWITCH STANDARD STACKED
DOUBLE-CIRCUIT POLE ARRANGEMENT (FMO)
X
08.13-11A
34-3/8"
23-1/16"
2
SOURCE
5
LOAD
6
14
13
7
PLAN VIEW
BILL OF MATERIALS
MACRO UNIT
CU
ITEM
NO.
1
-
COMPATIBLE
UNIT
QTY
REQ'D
CATALOG
NUMBER
-
1
2
-
1
3
-
1
4
-
1
5
-
6
6
-
6
7
8
9
-
6
2
15
10
-
6
11
-
12
12
-
3
13
-
3
14
-
6
15
16
17
18
19
20
21
22
23
24
-
3
1
35
-
9220109487
9220109490
013264
013308
152107
9220109491
390122
402179
013264
013308
152107
240306
220202
080577
011708
013264
013308
013346
101125
152123
152107
155464
010928
012277
013163
10542504
155331
010928
012277
013163
10542504
323422
014111
260123
152107
013308
013264
013264
014114
070431
072361
080212
152107
190204
121418
220139
190204
190312
013308
013264
013128
013407
9220184794
QTY
PER
CU
1
1
2
4
2
1
1
2
2
4
2
1
1
1
1
1
1
1
1
1
1
1
4
4
8
4
1
2
2
4
2
1
15
1
2
2
2
1
1
1
1
1
1
1
6
1
2.4
1
42
21
6
DESCRIPTION
SW, VRT, AUTO, 14.4KV, 900A, 35' CONTROL CABLE
SW, CONTROL, AUTO, INTELLI-TM-II, WITH RADIO
WASHER, SPRING COIL, FOR 5/8"
WASHER, SQUARE FLAT, 5/8"
BOLT, MACHINE, 5/8" X 12"
KIT, ANTENNA, UTILI-NET, MA-30-AB RADIO
TAPE, ELECTRICAL, 3/4" X 66' X .007 MIL
COMPOUND, INSUL, SEAL, PAD, 3-3/4"
WASHER, SPG, CO, S, FOR 5/8" BOLT
WASHER, 2-1/4", SQ, FLT, 13/16" HOLE
BOLT, MACHINE, 5/8" X 12"
BRACKET, ST. LIGHT, 6', WITH 30" RISE, GALV. STEEL
ARRESTER, 10KV, HD-MOV, SILICONE/RUBBER/POLYMER
INSULATOR, 25KV, DEADEND, POLYMER
BOLT, OVAL EYE, 5/8" X 10"
WASHER, SPRING COIL, FOR 5/8"
WASHER, SQUARE FLAT, 5/8"
WASHER, 3" SQUARE, CURVED, 13/16" HOLE
CLAMP, DE, SO, 336-1000 AL
BOLT, MACHINE, 3/4" X 14"
BOLT, MACHINE, 5/8" X 12"
LUG, COMPR, 795 AAC, 4-HOLE (BOTTOM OF PKR SW)
BOLT, MACHINE, SS, HEX HEAD, 1/2" X 2"
NUT, SS, HEX, 304 ALLOY, COARSE THREAD
WASHER, FLAT, ROUND, SI, BRONZE, FOR 1/2" BOLT
WASHER, RD, 1/2, SS
LUG, COMPR, 795 AL, 2-HOLE
BOLT, MACHINE, SS, HEX HEAD, 1/2" X 2"
NUT, SS, HEX, 304 ALLOY, COARSE THREAD
WASHER, FLAT, ROUND, SI, BRONZE, FOR 1/2" BOLT
WASHER, RD, 1/2, SS
GUARD, CABLE, PVC 2-1/4" X 10'
SCREW, LAG, 1/4" X 2"
SWITCH, 600 AMP BYPASS TYPE
BOLT, MACH, SQ, NUT, 5/8" X 12"
WASHER, SQUARE, 2-1/4", FLAT, 13/16", HOLE, GALV.
WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV.
WASHER, SPRING COIL, FOR 5/8"
SCREW, LAG, 1/2" X 4"
BRACKET, FIBERGLASS, STAND-OFF, 30"
STUD, LINE, POST, 5/8" X 1-3/4"
INSULATOR, POST, TIE TOP, 15/25KV, W/O STUD
BOLT, MACHINE, SQ, NUT, 5/8"X12"
#6 BC, HDW
TIE, PF, TOP F NECK 795 AL
ARRESTER-SECONDARY, 120/240 3-WIRE
WIRE, CU, BR, HRD, DRN, #6 (FOR ARRESTER GND)
WIRE, #2 CU, BR, SDW, 7, STR, #2 (FOR POLE GND)
WASHER, SQUARE FLAT, 5/8"
WASHER, SPRING COIL, FOR 5/8"
WASHER, SPRING, BELLEVILLE
WASHER, STAINLESS STEEL, ROUND, FLAT, 1/2"
HLC, 336 TO 795
NOTES:
1. SEE DWG. 08.13-11A FOR DESIGN SPECIFICATIONS AND DWG. 08.13-10A FOR OMNI-RUPTER CONTROLLER.
3
2
OMNI-RUPTER SWITCH STANDARD STACKED
1
5/24/13
0
11/29/10
REVISED
DANNA
ADCOCK
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
DOUBLE-CIRCUIT POLE ARRANGEMENT (FMO)
DWG.
08.13-11B
30" MIN.
5'-0" MAX.
2
LOAD
SOURCE
9-7/8"
SOURCE
LOAD
13
LOAD
18" MIN.
24"
SOURCE
SOURCE
LOAD
6"
11"
24"
9
7
12
15"
14"
18" MIN.
4-1/2"
6
8
4
1
3
#6 SD BC
24"
#2 SD BC
#2 SD BC
MANUAL OPEN
PULL-RING
NEUTRAL
5
30"
9" MINIMUM
RADIUS ON
CABLE
#6 SD BC
4' ABOVE
GROUND
MACROS
SA90HS_M
FRONT VIEW
SIDE VIEW
NOTES:
1. SEE DWG. 08.13-13B FOR PLAN VIEW AND NOTES. SEE DWG. 08.13-13C FOR BILL OF MATERIALS.
2. SEE DWG. 08.13-10C FOR OPTIONAL CONSTRUCTION BILL OF MATERIALS.
3. SEE DWG. 08.13-10D FOR CONTROL FACEPLATE.
4. SEE DWG. 08.13-10E FOR ANTENNA INSTALLATION.
3
DEC
2
DEM
DEP
DEF
OMNI-RUPTER SWITCH
1
8/5/14
EANES
EANES
ADCOCK
0
11/29/10
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
HORIZONTAL MOUNTING ARRANGEMENT (FMO)
X
08.13-13A
13
2
SOURCE
12
SOURCE
LOAD
SOURCE
LOAD
SOURCE
LOAD
6
7
5
1
LOAD
8
3
PLAN VIEW
NOTES:
1. SEE DWG. 08.13-13A FOR FRONT AND SIDE VIEWS.
2. SEE DWG. 08.13-13C FOR BILL OF MATERIALS. SEE DWG. 08.13-10C FOR OPTIONAL CONSTRUCTION BILL OF
MATERIALS.
3. SEE DWG. 08.13-10D FOR CONTROL FACEPLATE.
4. SEE DWG. 08.13-10E FOR ANTENNA INSTALLATION.
5. ARRESTERS SHOULD BE INSTALLED ON MOUNTING PADS PROVIDED ON BOTH SIDES OF THE OMNI-RUPTER
SWITCH. THE ARRESTER SOURCE LEAD SHOULD BE CONNECTED TO THE 795 JUMPER JUST BEYOND THE
OMNI-RUPTER 2-HOLE HIGH-VOLTAGE TERMINAL ON EITHER SIDE OF THE OMNI-RUPTER SWITCH TO KEEP THE
LEADS AS SHORT AS POSSIBLE. THE GROUND LEAD SHOULD BE RUN FROM THE GROUNDING CONNECTION ON
THE ARRESTER INTERRUPTER TO THE OMNI-RUPTER SUPPORT FRAME. THIS LEAD MUST BE LONG ENOUGH FOR
THE INTERRUPTER TO OPERATE, BUT SHORT ENOUGH TO CLEAR ADJACENT CONDUCTORS. ALL GROUND
CONNECTIONS MUST BE VERY SECURE, ESPECIALLY THE #2 BC CONNECTION AT THE BASE OF THE OMNI-RUPTER
SWITCH.
3
DEC
2
DEM
DEP
DEF
OMNI-RUPTER SWITCH
1
8/5/14
EANES
EANES
ADCOCK
0
11/29/10
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
REVISED
HORIZONTAL MOUNTING ARRANGEMENT (FMO)
X
08.13-13B
BILL OF MATERIALS
CU
ITEM
NO.
MACRO UNIT
1
SA90HS M
COMPATIBLE
UNIT
-
QTY
REQ'D
1
2
-
1
3
-
1
4
-
1
5
-
1
6
-
6
7
-
1
8
-
1
9
-
1
10
-
1
11
-
6
12
13
14
-
6
6
1
15
-
3
16
-
35
013128
013265
013308
152122
QTY
PER
CU
4
2
2
2
9220110451
1
080577
101125
013264
013308
152107
9220109490
390122
402179
9220109491
013264
013308
152107
240306
220202
013264
013308
152107
9220087868
9220091018
190204
9220117302
013264
152107
013308
013128
012277
010928
013407
010928
012277
013163
155464
10542504
010928
012277
013163
155331
10542504
9220184794
165277
220139
323422
014111
190312
3
6
2
4
2
1
1
2
1
2
4
2
1
1
1
1
1
1
1
1
1
2
2
2
4
12
12
24
6
6
6
6
6
2
2
4
1
2
1
1
1
1
45
1
CATALOG
NUMBER
DESCRIPTION
WASHER, ROUND, BELLEVILLE, FOR 1/2" BOLT
WASHER, SPRING COIL, FOR 3/4" BOLT
WASHER, SQUARE FLAT, 5/8"
BOLT, MACH, SQ, 3/4" X 12"
SW, HORIZ, AUTO, 14.4KV, 900A, G35' SHIELDED
CTRL CABLE IN LIQUIDTITE FLEXIBLE CONDUIT
INSULATOR, 27KV, POLYMER DEADEND
CLAMP, DEADEND, 795 AL
WASHER, SPRING COIL, FOR 5/8" BOLT
WASHER, SQUARE FLAT, 2-1/4"
BOLT, MACH, SQ, 5/8" X 12"
SWITCH, CTRL, AUTO
TAPE, ELEC, 3/4"
COMPOUND, INSUL, 3-3/4"
KIT, ANTENNA, UTILI-NET
WASHER, SPRING COIL, FOR 5/8" BOLT
WASHER, SQUARE FLAT, 2-1/4"
BOLT, MACH, SQ, 5/8" X 12"
BKT, STREET-LIGHT, 6' WITH 30" RISE, GALV STL
ARRESTER, LIGHTNING, 10KV
WASHER, SPRING COIL, FOR 5/8" BOLT
WASHER, SQUARE FLAT, 2-1/4"
BOLT, MACH, SQ, 5/8" X 12"
BKT, FBG, STAND-OFF
INSUL, 25KV, POLYMER
#6 BC, HDW
SWITCH, BYPASS, 3 PHASE, 600A, 15KV, HORIZONTAL
WASHER, SPRING COIL, FOR 5/8" BOLT
BOLT, MACHINE, SQ. NUT, 5/8" X 12"
WASHER, SQUARE FLAT, 5/8"
WASHER, SPRING, BELLEVILLE
NUT, SS, 1/2"
BOLT, MACHINE, SS, 1/2" X 2"
WASHER, SS, ROUND FLAT, 1/2"
BOLT, MACHINE, SS, HEX HEAD, 1/2" X 2"
NUT, SS, HEX, COARSE
WASHER, FLAT, ROUND, BRONZE, 1/2" BOLT
LUG, COMPRESSION, 4 HOLE 795 AL
WASHER, ROUND,1/2",SS
BOLT, MACHINE, SS, HEX HEAD, 1/2" X 2"
NUT, SS, HEX, COARSE
WASHER, FLAT, ROUND, BRONZE, 1/2" BOLT
LUG, 2 HOLE, 795 AL
WASHER, ROUND,1/2",SS
HLC, 336 TO 795
CONNECTOR, WEDGE, 795-795 STR.
ARR LIGHTNING SEC, 120/240V
CABLE GUARD, 2-1/4" X 10"
LAG SCREWS, 1/4" X 2"
GROUND WIRE, 7 STR, #2 CU, 1 LB.
NOTES:
1. SEE DWG. 08.13-13A FOR FRONT AND SIDE VIEWS. SEE DWG. 08.13-13B FOR PLAN VIEW AND NOTES.
2. SEE DWG. 08.13-10C FOR OPTIONAL CONSTRUCTION BILL OF MATERIALS.
3
2
OMNI-RUPTER SWITCH
R
1
0
11/29/10
REVISED
HOFFMAN
GUINN
ELKINS
BY
CK'D
APPR.
HORIZONTAL MOUNTING ARRANGEMENT (FMO)
DWG.
08.13-13C
NOTES:
1. METRICOM EQUIPMENT MOUNTED
ABOVE THE NEUTRAL POSITION SHALL
BE INSTALLED AND MAINTAINED ONLY
BY PERSONS QUALIFIED TO WORK IN
THE SUPPLY SPACE, PER SECTION
224 IN THE NESC.
POLE TOP
FRAMING
AS REQUIRED
2. INSTALL ONLY ON POLES LOCATED
ON PUBLIC RIGHT OF WAY. DO NOT
INSTALL ON PRIVATE AREA LIGHTS NOR
DECORATIVE POLES.
O
. T SE
IN HA
P
M
"
T
43 ES
S
O
CL
PREFERRED NEUTRAL
LOCATION
40" MIN.
TO CLOSEST SECONDARY, SERVICE
OR NEUTRAL
40" MIN.
TO CLOSEST SECONDARY,
SERVICE OR NEUTRAL
LEVELING WEDGE
SEE ANTENNA
MOUNTING BRACKET
DETAIL BELOW
ANTENNA
POWER CABLE
METRICOM RADIO TRANSCEIVER
USED TO SUPPORT
WIRELESS MODEMS
10"
40" MIN.
TO CLOSEST SECONDARY,
SERVICE OR NEUTRAL
POWER CABLE
ALTERNATE NEUTRAL
LOCATION
LIGHTING
BRACKETS PER
DWG. 30.02-25
MOUNTING BRACKETS
SUPPLIED BY METRICOM
LEVELING WEDGE
SUPPLIED BY METRICOM
6.8"
4"
3"
12"
ANTENNA
3"
MOUNTING BRACKET DETAIL
3
2
INTELLITEAM RADIO TRANSCEIVERS (FMO)
1
0
4/22/10
REVISED
R
GUINN
GUINN
ELKINS
DWG.
BY
CK'D
APPR.
08.13-15