Thyristor
AC/DC
TIG Arc
.,'"
~
~-ISO14001
~/i.I.\iE~~
Controlled
Pulse
Welder
~
DCTIG
Automatic
DCTIG
TIG Filler
TIG
Arc spot
w/Robot
FEATURES
i
1, It has good output characteristics,
stable arcing
performance
from the small current to rat~d '"
current
for welding of various thic'knesses
of
plates,
especially suitable for thin plates.
High quality welding, constant penetration and stable
welding bead can be obtained
by the good arc
concentration.
2, Very useful as power source for Butt welding of
thick plate and pipe which needs high quality and
penetration bead.
4, Very easy to operate vertical welding,
TIG filler
welding operation, tack welding for thin plate and
repeated short length welding, etc... by heat capacity
control of pulse current. So, high efficiency welding
can be done.
SPECIFICATIONS
5, Fine treatment and increase the weld quality of
welding start / finish with Up-slope control and Downslope control.
6, Precisely controls the arc conditions
for AC/DC
manual welding of stainless-steel, special steel such
as Cr-Mo steel by means of refined electronics
techniques so that optimum dynamic characteristics
can be obtained.
7, By using cleaning width adjustor, more oxide can be
effectively removed at low welding current while the
loss of tungsten electrode can by reduced at high
welding current.
8. Equipped with advanced reactor control technology,
its AC square wave output becomes very stable and
stability is thus enhanced considerably, thereby high
welding quality is obtainable.
Current
'-/
The * mark shows
in case of DC manual
welding,
DC TIG welding
TIG welding which is adjusted to [WIDE] side of cleaning
Please inform us of primary voltage.
[JJ
3.
Automatic
and AC
width control.
Unstable arc
Stable arc
.."'\
.Initial
current control
.Pulse
current
control
.Able to choose any pulse current as you like.
I
Current
Time
-
[~~:::=~f -
.To prevent burn through for thin plate welding.
For confirmation of arc start point.
I,I
prevent
incomplete
~nnM
penetration
1 I
~J={=
CurrentI large iniliai current
.To
Small bead
J li~
lime
for thick
I
Penetration
(shallow)
.Pulse
plate welding.
ratio control
.Penetration control is easy, because it can
control average current keeping strong and
stable arc with pulse TIG welding.
.Up-slope
time control
.To improve the weld quality at welding start by
smooth changing from initial current to welding
current with Up-slope time control.
.Pulse
frequency control
.To change number of welding bead ripples and
bead breadth.
1.-
.Down-slope
time control
.Smooth ending of welding with Down-slope
time control.
Frequency
.Three
.Gas
kinds of crater treatment
afterflow time control
control
.Arc
spot welding
time
control
~
~
TIG WELDING TORCH
ARGON GAS REGULATOR WITH FLOW METER
High durable against heat.
Perfectly airtight and watertight.
Small, light and easy to manipulate.
For reducing pressure of Argon in
high pressure gas cylinder to the
proper secondary pressure and for
adjusting flow rate.
I
Max Pressure 200 kg/cm2
Flow rate range 1-25 /min
YT -208T
f
YX-251 A
.COOLING
WATER TANK
YX-O9KBA1
.REMOTE
.Pistol
type
"Cooling
water flow rate 0.71/min pressure 1.0-3.0
kg/cm2
CONTROLLER
YC-304URW
Optional Nozzles for TIG Welding
NOZZLE WITH GASLENS
BIG CALIBER NOZZLE
.Use in combination with Collet
body w/gas lens and adaptor
LONG NOZZLE
ARC SPOT NOZZLE
Adaptor for arc spot
Arc spot nozzle
* Use in combination
with
adaptor for Arc Spot.
.Electrodes for TIG Welding
A little consume of electrode,
good arc
startability and stability. Increase the working
efficiency of TIG welding.
c~"*'
2% ThoMIed
CERIUMED TUNGSTEN
ELECTRODE r
1
Lan"'"me
"'...e'
2%
e_IDC
--TIG)Low
llG)low
(DCllG)
.~~m-
.~e~mp'?,
-.ze(mm)
"am
"'actu,.o
","e
by
l
Mao"actuc,"
plam
lathe
by
!
Mao"a,,",,"
p"m
Ie'"
VN-10T2S
YN-10C2S
VN-10C2S
fN-18T2S
YN-16l2S
VN-16l2S
fN-20T2S
YN-2(H-2S
YN-2Ol2S
,IN-24T2SI
YN-24t2S
VN-..LOS
-.S
ELECTRODE
subject to change
2%",.,Ie,
Ce',mod
electrodelACIDC
I
.
THORIATED TUNGSTEN
ELECTRODE
Specifications
1
",.-
fN.-aT2S
without notice.
I
~~~
IYN-=
YN~
YN-48L2S
I ~YN-4<H.2S
.-L2S
YN-48L2S
2004.06