TQP4M0011
Low Loss SP3T Reflective Switch
Applications
•
•
•
•
•
•
•
WLAN
Cellular Infrastructure
Test and Measurement
Smart Energy
UHF/VHF
LMR
General Purpose Broadband Wireless
12-pin 3x3 mm QFN Package
Product Features
•
•
•
•
•
•
Functional Block Diagram
General Purpose
Broadband: 100-6000 MHz
Low Insertion Loss: 0.6 dB at 2 GHz
High Input IP3: +55 dBm at 2 GHz
CMOS Compatible Triple Voltage Control
Lead Free, RoHS Compliant QFN Package
Pin 1 Reference Mark
Topside View
N/C
RFC
N/C
12
11
10
V3
1
9
V1
RF3
2
8
RF1
GND
3
7
GND
4
5
6
GND
RF2
V2
Backside Paddle - RF/DC GND
Pin Configuration
General Description
The TQP4M0011 is GaAs FET single-pole, three throw
(SP3T) switch with control signals from three
independent control bias lines. Signal path (switch)
states may be controlled using DC voltages operating
from 1.8 to 5 Volts. The TQP4M0011 has 100 to 6000
MHz broadband performance
The TQP4M0011 is packaged in a RoHS-compliant,
compact 12-pin 3x3 mm QFN package.
The TQP4M0011 is an ideal choice for wireless
infrastructure and test & measurement applications
requiring low insertion loss and high input IP3. It can
also be used for any general purpose RF application
where isolation is critical.
Pin No.
Symbol
1
2
3, 4, 7
5
6
8
9
10, 12
11
Backside Paddle
V3
RF3
GND
RF2
V2
RF1
V1
N/C
RFC
RF/DC GND
Ordering Information
Part No.
TQP4M0011
TQP4M0011-PCB
Description
SP3T Reflective Switch
0.1- 6.0 GHz Evaluation Board
Standard T/R size = 2500 pieces on a 7” reel
Datasheet: Rev. C 05-01-14
© 2014 TriQuint
- 1 of 6 -
Disclaimer: Subject to change without notice
www.triquint.com
TQP4M0011
Low Loss SP3T Reflective Switch
Absolute Maximum Ratings
Recommended Operating Conditions
Parameter
Parameter
Rating
Storage Temperature
RF Input Power, CW, 50Ω, T = 25°C
Control Voltage (V1/V2/V3)
-65 to 150°C
+33 dBm
+6 V
Operation of this device outside the parameter ranges
given above may cause permanent damage.
Min Typ Max Units
V1/V2/V3 High State
Operating Temp. Range
1.8
-40
3.3
5.0
+85
V
°C
Electrical specifications are measured at specified test
conditions. Specifications are not guaranteed over all
recommended operating conditions.
Electrical Specifications
Test conditions unless otherwise noted: Temp.=+25°C, 50 Ω system
Parameter
Operational Frequency Range
Control Voltage
Insertion Loss
Isolation
Return Loss – RFC Port
Input P1dB
Input IP3
Switching Speed
Control Voltage Bias Current
Conditions
Low
High
0.1 – 1.0 GHz
1.0 – 2.5 GHz
2.5 – 3.0 GHz
3.0 – 4.5 GHz
4.5 – 6.0 GHz
0.1 – 1.0 GHz
1.0 – 2.5 GHz
2.5 – 3.0 GHz
3.0 – 4.5 GHz
4.5 – 6.0 GHz
0.1 – 1.0 GHz
1.0 – 2.5 GHz
2.5 – 3.0 GHz
3.0 – 4.5 GHz
4.5 – 6.0 GHz
f = 2 GHz
f = 2 GHz ,
Pout=+15 dBm/tone, Δf=1 MHz
Low
High
6000
0.4
5.0
3.3
0.4
0.6
0.8
1.2
1.5
36
34
33
31
30
29
19
16
12
10
+34
Units
MHz
V
V
dB
dB
dB
dBm
+55
dBm
110
15
ns
uA
Switch Control Truth Table
Control Voltages
Signal Path State
V1
V1
V3
RFC to RF1
RFC to RF2
RFC to RF3
Off (isolation)
Off (isolation)
On (insertion loss)
Low Low High
Off (isolation)
On (insertion loss)
Off (isolation)
Low High Low
Off (isolation)
Off (isolation)
High Low Low On (insertion loss)
All Other States
Datasheet: Rev. C 05-01-14
© 2014 TriQuint
Max
V1 or V2 or V3=5 V
Bias Condition
≤ 0.4 V
≥ 1.8 V
Typ
100
0
1.8
tON,tOFF (50% CTL to 10/90% RF)
Digital Control Voltages
State
Min
- 2 of 6 -
N/A
N/A
N/A
Disclaimer: Subject to change without notice
www.triquint.com
TQP4M0011
Low Loss SP3T Reflective Switch
J1
Reference Design (TQP4M0011-PCB)
J1
RFC
J7
V3
J5
J7
100 pF
C
5
J4
12
C
7
C2
C7
U1
J2
C3
RF3
C
6
C4
C4
J4
2.2 pF
100 pF
11
C5
10
1
9
2
8
C3
2.2 pF
100 pF
7
3
J6
J5
J2
RF1
6
5
C1
4
J8
J8 GND
J5
V1
C2
J6
V2
C1
C6
100 pF
2.2 pF
J3
RF2
J3
Notes:
1. See Evaluation Board PCB Specifications section for material and stackup.
Typical Performance - (TQP4M0011-PCB)
Test conditions unless otherwise noted: Temp=25°C, 50 Ω system
Conditions
Parameter
Frequency
Insertion Loss
RFC Port Return Loss
Isolation
Input P1dB
Input IP3
1
0.5
29
36
+34
+53
RFC Port to RF1 or RF2 or RF3
RFC Port to RF1 or RF2 or RF3
Pout= +15 dBm/tone, Δf=1 MHz
Typical Value
2
0.6
25
35
+34
+55
Units
3
0.8
16
33
+33.5
+56
GHz
dB
dB
dB
dBm
dBm
Performance Plots - (TQP4M0011-PCB)
Test conditions unless otherwise noted: Temp=+25°C, 50 Ω system
RFC to RF1/2 Insertion Loss vs. Freq.
0.0
RFC Port Return Loss Vs. Frequency
0
Temp.=+25°
-0.5
RFC to RF1/2 Isolation vs. Freq.
0
Temp.=+25°
Temp.=+25°
-10
-10
-1.5
|S21| (dB)
-20
|S11| (dB)
|S21| (dB)
-1.0
-20
-2.0
-30
-40
-30
-2.5
-3.0
-50
0
1
2
3
Frequency (GHz)
Datasheet: Rev. C 05-01-14
© 2014 TriQuint
4
5
6
-40
0
1
2
3
Frequency (GHz)
- 3 of 6 -
4
5
6
-60
0
1
2
3
Frequency (GHz)
4
5
6
Disclaimer: Subject to change without notice
www.triquint.com
TQP4M0011
Low Loss SP3T Reflective Switch
Pin Configuration and Description
Topside View
Pin No.
Symbol
1
Description
V3
Switch state control voltage
2
RF3
RF Input/Output port 3
3, 4, 7
GND
Ground
5
RF2
RF Input/Output port 2
6
V2
8
RF1
9
V1
Switch state control voltage
10, 12
N/C
No electrical connection. Provide grounded land pads for PCB mounting integrity.
11
Backside
Paddle
RFC
Antenna port
RF/DC Ground. Use recommended via pattern and ensure good solder attach for
best thermal and electrical performance.
Switch state control voltage
RF Input/Output port 1
RF/DC GND
Evaluation Board PCB Specifications
PCB 1093782 Material and Stack-Up
0.014"
0.062" ± 0.006"
Finished Board
Thickness
Nelco N-4000-13
εr=3.7 typ.
1 oz. Cu top layer
1 oz. Cu inner layer
Core
1 oz. Cu inner layer
0.014"
Nelco N-4000-13
1 oz. Cu bottom layer
50 ohm line dimensions: width = .028”, spacing = .028”
Datasheet: Rev. C 05-01-14
© 2014 TriQuint
- 4 of 6 -
Disclaimer: Subject to change without notice
www.triquint.com
TQP4M0011
Low Loss SP3T Reflective Switch
Mechanical Information
Package Marking and Dimensions
Marking: Product Code – XXXXX
Year/Week - YYWW
Assembly Code - XXXXX
1.45±0.05 Exp.DAP
Pin 1 Locator
3.00±0.05
XXXXX
YYWW
XXXXX
PIN #1 IDENTIFICATION
SQ. 0.434
0.50 Bsc
3.00±0.05
1.45±0.05 Exp.DAP
0.23±0.05
0.40±0.05
Top View
1.00
Ref.
GND/Thermal Pad
Bottom View
0.85±0.05
0.000-0.050
Side View
.20 Ref.
Notes:
1. All dimensions are in millimeters . Angles are in degrees.
2. Dimension and tolerance formats conform to ASME Y14.4M-1994.
3. The terminal #1 identifier and terminal numbering conform to JESD 95-1 SPP-012.
PCB Mounting Pattern
Pin 1 Locator
1.50
Package Outline
0.31
5X 3
0.38
0.16
12X 0.52
12X 0.32
0.76
1.50
0.50 Pitch 12X
0.38
0.76
COMPONENT SIDE
Notes:
1. All dimensions are in millimeters. Angles are in degrees.
2. Use 1 oz. copper minimum for top and bottom layer metal.
3. Drill via holes as required for a final plated thru diameter of 0.152 mm (0.006”).
4. Ensure good package backside paddle solder attach for reliable operation and best electrical performance.
Datasheet: Rev. C 05-01-14
© 2014 TriQuint
- 5 of 6 -
Disclaimer: Subject to change without notice
www.triquint.com
TQP4M0011
Low Loss SP3T Reflective Switch
Product Compliance Information
ESD Sensitivity Ratings
Solderability
Compatible with both lead-free (260°C max. reflow
temperature) and tin/lead (245°C max. reflow
temperature) soldering processes.
Caution! ESD-Sensitive Device
Package contact plating: NiPdAu
ESD Rating: Class 1B (RF Ports)
Value:
≥ 500 volts to < 1,000 volts
ESD Rating:
Value:
Test:
Standard:
RoHs Compliance
Class 0B (DC Lines)
≥ 125 V to < 250 volts
Human Body Model (HBM)
ESDA/JEDEC Standard JS-001-2012
MSL Rating
MSL Rating: Level 1
Test:
260°C convection reflow
Standard:
JEDEC Standard IPC/JEDEC J-STD-020
This part is compliant with EU 2002/95/EC RoHS
directive (Restrictions on the Use of Certain Hazardous
Substances in Electrical and Electronic Equipment).
This product also has the following attributes:
• Lead Free
• Halogen Free (Chlorine, Bromine)
• Antimony Free
• TBBP-A (C15H12Br402) Free
• PFOS Free
• SVHC Free
Important Notice
For the latest specifications, additional product information, worldwide sales and distribution locations, and information
about TriQuint:
Web:
www.triquint.com
Tel:
+1.503.615.9000
Email: info-sales@triquint.com
Fax:
+1.503.615.8902
For technical questions and application information:
Email: sjcapplications.engineering@triquint.com
Contact Information
The information contained herein is believed to be reliable. TriQuint makes no warranties regarding the information
contained herein. TriQuint assumes no responsibility or liability whatsoever for any of the information contained
herein. TriQuint assumes no responsibility or liability whatsoever for the use of the information contained herein. The
information contained herein is provided "AS IS, WHERE IS" and with all faults, and the entire risk associated with
such information is entirely with the user. All information contained herein is subject to change without notice.
Customers should obtain and verify the latest relevant information before placing orders for TriQuint products. The
information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any
patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or
anything described by such information.
TriQuint products are not warranted or authorized for use as critical components in medical, life-saving, or lifesustaining applications, or other applications where a failure would reasonably be expected to cause severe personal
injury or death.
Datasheet: Rev. C 05-01-14
© 2014 TriQuint
- 6 of 6 -
Disclaimer: Subject to change without notice
www.triquint.com