EXHIBIT B - SCOPE OF WORK
CNMCC Student Resource Building room SRC-204 (Richard Barr Boardroom)
The following information specifies audiovisual needs for the CNMCC Main Campus SRC-204 equipment
upgrade.
The total number of rooms is one (1) and the overview of the room functionality is below:


The following is intended to further describe the Work and clarify design intent and is not an
exhaustive description of the systems
A ceiling mounted front projection screen shall be provided by the selected vendor for display of
a single vendor provided video projector located on a ceiling mount. The Vendor is responsible
for all required hardware and mounts to mount the video projector in an inverted position. A
vendor provided spare projector lamp will be required.
The following sources can be displayed:

Inputs for portable devices located in the 3 existing floor pockets, comprised of VGA with 3.5mm
audio and composite video with stereo audio and controlled by the existing CRESTRON Control
Unit located in the storage closet on the SW side of the room.
Speech and program audio volume control/equalization/amplification shall be provided. This room will
be equipped with ceiling mounted pendant speakers for use as program audio reinforcement.


A mixing console, microphones and all processing equipment is provided for live audio mixing
and will be located in an area to be determined by the specified installer and CNM Audiovisual
Services within SRC-204. All microphone inputs will be routed directly to the mixing console.
Equipment rack for switchers, audio amplifiers and signal processing equipment shall be located
in the above mentioned area to be determined by the specified installer and CNM Audiovisual
Services. Sufficient cable length shall be provided to allow the rack to be pulled out for service
and maintenance.
A video capture system will be provided for recording and storage of scheduled board meetings and
other meetings as determined by CNM Administration.
The following items will need to be provided and will be the components used for the installation.
Specifications listed below are a minimum level of performance. Equipment substitutions shall be
clearly noted as part of the bid response and are subject to review and approval by CNM. The
equipment shall meet the following functional requirements:
Video Projector: Hitachi CP-WX8255 (Ceiling Mounted w/CHIEF RPA Universal Projector Mount to
existing mounting pipe)
1






5500 ANSI Lumens 16:10 WXGA LCD
Contrast 3,000:1
RJ-45 Port
Zoom Lens : 1.5 – 3.0:1 w/Standard Lens
3,000 Hour Lamp Replacement Cycle
Provide Spare lamp for projector
Screen: DaLite 87135V Cinema Contour, DM 18D 108x144 Screen
Video Capture System to consist of the following:






CRESTRON Capture-HD High-Definition Capture Recorder
CRESTRON QM-RMC Room Media Controller
CRESTRON TPMC-4SMD 4.3” Designer Touch Screen
CRESTRON TTK-4SM Table Top Kit for TPMC-4SMD
CRESTRON PWE-4803RU PoE Injector
CRESTRON Cam-IPTZ-100 PTZ Camera for Capture HD
Audio Reinforcement System to consist of the following:



















Mid Atlantic PFR2428CR Reference Series rack 42” w/24 Spaces. Cherry Rain Finish
Mid Atlantic PD915Rc20 9out, 15A, Rack mount Power Unit w/20’ cord
3 @ Mid Atlantic UD2 2space Utility Drawer
3 @ Mid Atlantic F12 2 Space Foam Inserts
10 @ Shure MX415C 15” Shock Mount Gooseneck Mics
Shure Wireless Desk Top Base (4@ MX890G4, 4@ MX890G5, 2@ MX890H5)
2 @ Shure SLX24SM58H% Handheld SM 58 Wireless systems
2 @ Shure SCM810 Mixer Audio Automatic w/Logic Control
Shure Wireless Receiver to include: 4@ SLX4LG4, 4@ SLX4LG5, 2@ SLX4LH5
4@ Shure UA844SWB Wideband UHF Active Antenna Splitter
2@ Shure UA820G10 ½ Wave Antenna for P10T, 470-524 MHz
Shure DFR22 Processor 2x2 Audio Feedback Eliminator
QSA CMX300V Power Amplifier
2 @ Shure 2320050055 SM 58 Table Top Mic Stands
18 @ Kramer CXLMXLF 3’ XLR-M to XLR-F Audio Cables
6 @ OWI M6720W Mercury Pendant Speakers – White
1000’ of 18/2 Conditioned Shielded Plenum Speaker Wire
Kramer WA1XLM XLR-M to Solder Cups
Comprehensive NC3FXX Neutrik 3 Pin XX Series F XLR
2
Control System programming:
Provide fully-functional control systems with all required control system programming. Vendor shall
have a Crestron Certified programmer assigned to this project. A certified independent programmer
is acceptable. Vendor shall provide the name, Certification level and Certification Number as part of
the bid response.
The vendor will be responsible for the fully operational installation and Crestron component
programming of the listed systems and components using all necessary and construction rated
cables. Crestron approved cable shall be provided for all Digital Media components.
The Vendor will provide all equipment and cabling required to enable these systems. Meeting all
applicable Codes is the sole responsibility of the Vendor. The data network and electrical 120V outlets
will be the provided by CNM. Vendor to extend 120V power from the wall outlet to the audio and
reinforcement system and the Video Capture system and provide Ethernet cable where applicable. All
cables shall be neatly bundled.
Vendor shall have a Crestron Certified Digital Media Engineer (DMC-E) assigned to this project on staff.
Vendor shall provide the technicians name and Certification Number as part of the bid response.
Vendors shall supply a list of all sub-contractors who will be working on this project as part of the bid
response.
The Vendor will be responsible for providing a final system design that meets CNM specifications, meets
all applicable code requirements and achieves the desired functionality. The selected Vendor will be
responsible for a complete and fully functional installation. The Vendor will test systems and
demonstrate to CNM staff (Audiovisual Services) system functionality. CNM reserves the right to accept
or deny the installed systems based on demonstrated functionality.
3