Engineering
Safety &
Productivity
PowerMate™
Drilling Pin and Sleeve Connectors
Greatest
Personnel
Safety
Improved
Rig-up &
Rig-down
Operation
Maximized
Reliability
PowerMate ™ Plugs, Receptacles and Connectors
POWERMATE DRILLING RIG
POWER CONNECTIONS
The PowerMate offering is designed to support
modularity of drilling rig systems by providing
safe and reliable power connections for riggingup and rigging-down equipment quickly and
efficiently.
This offering is the ideal rig power connection
solution providing:
• Longer product life
• Reduced maintenance
• Enhanced safety
• Easy installation
The PowerMate product offering is also
compatible with all UL 1686 listed plugs and
receptacles, including:
• Cooper Crouse-Hinds Arktite™
• Appleton Powertite®
• Killark VersaMate®
TABLE OF CONTENTS
Applications����������������������������������������������������� 2
Specifiable Features���������������������������������������� 3
Certifications��������������������������������������������������� 3
Standard Materials������������������������������������������ 3
Standard Finishes�������������������������������������������� 3
Options������������������������������������������������������������ 3
PowerMate™ Features and Benefits�������������4-5
PowerMate™ Offering:
30A������������������������������������������������������������������ 6
60A������������������������������������������������������������������ 7
100A���������������������������������������������������������������� 8
150A���������������������������������������������������������������� 9
200A and 400A Offering���������������������������������� 9
APPLICATIONS
Grounding������������������������������������������������������ 10
PowerMate Plugs, Receptacles, and
Connectors are used:
• On SCR/VFD houses to provide power to
rig equipment such as shakers, agitators,
lighting circuits, mud pumps, motors, etc.
• To quickly and efficiently connect power
during rig-ups and disconnect power during
rig-downs.
Electrical Rating Ranges������������������������������� 10
Product Dimensions�������������������������������������� 11
Replacement Parts���������������������������������������� 12
Wire Sizes������������������������������������������������������ 12
PowerMate™ Part Numbers��������������������������� 13
Plug and Receptacle Solutions
for Land-Based Drilling����������������������������14-15
2
SPECIFIABLE FEATURES
Lockout Plug
Safety Insulator
Diamond Clamp
Split Pin Contacts
STANDARD MATERIALS
• Receptacle housing, plug and cord
connector bodies - high impact strength
copper-free aluminum (less than 0.4% copper)
• Back boxes - cast aluminum
• Insulation - fiberglass reinforced polyester
• Contacts - naval brass
Type P Cable
STANDARD FINISHES
CERTIFICATIONS
• UL Standards: UL 1682, UL 1686,
NEMA 250
• CSA Standard: C22.2 No. 182.1
• Listed for use with Type P cable, flexible cord
and cables rated for extra hard usage
• NEMA 4X
• Copper-free aluminum - epoxy powder coat
• Fiberglass reinforced polyester - natural (red)
• Naval brass - natural
OPTIONS
• -RS...Reverse Service. Receptacle
assembled with plug interior and plug
assembled with receptacle interior. For
applications where plug is energized to feed
normally de-energized receptacle.
NOTE: 30, 60, and 100A interiors can be
interchanged in the field using a screwdriver.
CDR - S22 (reverse service)
PowerMate Receptacle
Transformer
Switch
CCP PowerMate
Plug
Generator
CCP - RS (reverse service)
PowerMate Plug
CDR - RS
PowerMate Receptacle
• -P4...Special Polarity. Receptacle interior
rotated 22 1⁄2 degrees to right and plug
changed to match. For use where two or
more receptacles of the same ampere rating,
style, and number of poles are to be installed
in the same area for use on different voltages
and/or frequencies. Prevents insertion of a
plug in a receptacle with different electrical
rating.
3
PowerMate ™ Features and Benefits
Specifiable Features
1
Lockout Plug (Patent Pending)
• Guarantees isolated power supply with OSHA compliant lockout/tagout.
• Ensures plug cannot be inserted into receptacle when maintenance is
being performed downstream of power supply.
2
Fixed Safety Insulator (Patent Pending)
• Prevents electrical shock and shorts with plastic barrier between insulator
body and metal housing.
• Fixed-in-place design ensures insulator will not be lost or discarded
during cable termination process.
3
8-Point Diamond Cable Clamps (Patent Pending)
• 8 points of contact around diameter of cable for increased grip and even
distribution of pressure.
• Cable jacket does not get pinched, eliminating potential for damage
to internal conductors.
4
Split Pin Contact Design
• Provides nearly 360° of contact at every insertion, ensuring protection
against heat rise and eliminating arcing on critical surfaces.
• Self-wiping at every insertion to remove foreign particles that create
electrical resistance and product failure.
5
Extended Cable Range
• Industry’s largest cable diameter range.
• Specifically designed, third party tested and certified for use with Type P
cable.
• Sealing system utilizes industry standard bushings.
6
Enhanced Nomenclature and Nameplate
• Easily understandable nomenclature increases ease of part configuration
identification.
• Mechanically attached nameplate ensures that critical information is
permanently fixed to product.
7
Spring and Threaded Cover
• Each receptacle comes with both spring cap and threaded cap to provide a
variety of cover options.
8
Combination Drive Stainless Steel Hardware
• Increases ease of installation by allowing for more than one option for
installation tools.
• Stainless steel external hardware eliminates corrosion on critical
components and extends product life.
9
Handle Body
• Thick epoxy powder coating is standard finish on PowerMate products.
• Coating reduces corrosion and increases life of product.
• Industry standard profile increases ease of plugging and unplugging.
10
Combination Slot and Hex Mechanical Lugs*
• Increases ease of installation by allowing for more than one option for
installation tools.
• Hex head allows for easy achievement of specified torque value.
11
Insulator Assemblies
• Unimpeded, easy-access phase and ground terminals make wire
termination quick and easy.
• Molded-in-place markings for phase/ground and conductor strip lengths
reduce installation errors.*
Lockout Plug
Safety Insulator
Diamond Clamp
Split Pin Contacts
Type P Cable
Compatible
with all UL 1686
listed plugs and
receptacles.
Type P Cable
Lockout Compliant
*60, 100, and 150A offering.
4
5
60 AMP
30 AMP
Receptacles, Plugs and Connectors
Receptacles, Plugs and Connectors
NEMA 4X Watertight
600 VAC / 250 VDC
50 - 400 Hz
NEMA 4X Watertight
600 VAC / 250 VDC
50 - 400 Hz
DESCRIPTION AND
CONFIGURATION:
2 Wire
2 Pole
Style 1
CDR3022
CABLE
RANGE
CAT.
NO.
.390-1.375” CCP3022BC .390-1.375” CRC3022BC
GR
GR
3 Wire
4 Pole
Style 2
GR
CDR3034
.390-1.375”
CRC3033BC
CCP3034BC .390-1.375” CRC3034BC
GR
CDR3044
.390-1.375” CCP3044BC .390-1.375” CRC3044BC
GR
CABLE
RANGE
CAT.
NO.
CABLE
RANGE
CAT.
NO.
CDR6022
.440-1.375” CCP6022BC 0.440-1.375” CRC6022BC
CDR6023
.440-1.375” CCP6023BC 0.440-1.375” CRC6023BC
CDR6033
.440-1.375” CCP6033BC 0.440-1.375” CRC6033BC
CDR6034
.440-1.375”
CDR6044
.440-1.375” CCP6044BC 0.440-1.375” CRC6044BC
CCP6034BC 0.440-1.375” CRC6034BC
GR
Back Boxes (for Receptacles)
HUB SIZE
CEE
CERH
CERC
⁄2”
CEE13
CERH13
CERC13
3
⁄4”
CEE23
CERH23
1”
CEE33
CERH33
6
4 Wire
4 Pole
Style 1
CORD CONNECTOR
PLUG
GR
3 Wire
3 Pole
Style 1
.390-1.375” CCP3033BC .390-1.375”
RECEPTACLE
GR
GR
GR
.390-1.375” CCP3023BC .390-1.375” CRC3023BC
Back Boxes (for Receptacles)
1
2 Wire
2 Pole
Style 1
GR
CDR3033
3 Wire
4 Pole
Style 2
CAT.
NO.
DESCRIPTION AND
CONFIGURATION:
2 Wire
3 Pole
Style 2
CDR3023
3 Wire
3 Pole
Style 1
CORD CONNECTOR
PLUG
CABLE
RANGE
GR
GR
GR
GR
2 Wire
3 Pole
Style 2
4 Wire
4 Pole
Style 1
RECEPTACLE
• The back boxes at left are standard with
Corro-Free™ epoxy powder coat finish for
increased corrosion resistance.
• For optional reversed interior, use suffix
-RS (see page 3).
• For optional rotated interior, use suffix
-P4 (see page 3).
• For dimensions, see page 11.
• Maximum conductor size (wire well) 0.281”
(see page 12).
HUB SIZE
CEE
CERH
CJA
CERC
⁄2”
CEE36
CERH36
CJA310
CERC36
CERC23
1-1⁄4”
CEE46
CERH46
CJA410
CERC46
CERC33
1-1⁄2”
CEE56
CERH56
CJA510
CERC56
2”
----
----
CJA610
----
1
• The back boxes at left are standard
with Corro-Free™ epoxy powder
coat finish for increased corrosion
resistance.
• For optional reversed interior, use
suffix -RS (see page 3).
• For optional rotated interior, use
suffix -P4 (see page 3).
• For dimensions, see page 11.
• Maximum conductor size (wire well)
0.312” (see page 12).
7
150 AMP
100 AMP
Receptacles, Plugs and Connectors
Receptacles, Plugs and Connectors
NEMA 4X Watertight
600 VAC / 250 VDC
50 - 400 Hz
NEMA 4X Watertight
600 VAC / 250 VDC
50 - 400 Hz
DESCRIPTION AND
CONFIGURATION:
2 Wire
2 Pole
Style 1
GR
GR
GR
GR
2 Wire
3 Pole
Style 2
CDR1022
CORD CONNECTOR
PLUG
CABLE
RANGE
CDR1023
CAT.
NO.
CABLE
RANGE
CAT.
NO.
.875-1.906” CCP1022CD .875-1.906” CRC1022CD
.875-1.906” CCP1023CD
.875-1.906” CRC1023CD
GR
3 Wire
3 Pole
Style 1
CDR1033
.875-1.906” CCP1033CD
.875-1.906” CRC1033CD
DESCRIPTION AND
CONFIGURATION:
3 Wire
4 Pole
Style 2
4 Wire
4 Pole
Style 1
GR
CDR15044
GR
CAT.
NO.
CABLE
RANGE
CAT.
NO.
.875-1.906” CCP15034CD .875-1.906” CRC15034CD
1.250-2.190” CCP15034DE 1.250-2.190” CRC15034DE
.875-1.906” CCP15044CD .875-1.906” CRC15044CD
1.250-2.190” CCP15044DE 1.250-2.190” CRC15044DE
200 AMP and 400 AMP Arktite ™
CDR1034
.875-1.906”
CCP1034CD
.875-1.906” CRC1034CD
GR
Receptacles, Plugs and Connectors
200A and 400A options available as part of our Cooper Crouse-Hinds Arktite™ Series
CDR1044
.875-1.906” CCP1044CD
.875-1.906” CRC1044CD
GR
HUB SIZE
CJA
⁄2”
CJA310
1-1⁄4”
CJA410
1-1⁄2”
CJA510
2”
CJA610
8
CABLE
RANGE
CDR15034
CORD CONNECTOR
PLUG
Back Boxes (for Receptacles) - see page 8.
AMPERAGE AND
CONFIGURATION:
Back Boxes (for Receptacles)
1
RECEPTACLE
GR
3 Wire
4 Pole
Style 2
4 Wire
4 Pole
Style 1
RECEPTACLE
CJA ADAPTER ONLY
CJA100
• The back boxes at left are standard with
Corro-Free™ epoxy powder coat finish for
increased corrosion resistance.
• For optional reversed interior, use suffix -RS
(see page 3).
• For optional rotated interior, use suffix -P4
(see page 3).
• For dimensions, see page 11.
• Maximum conductor size (wire well) 0.390”
(see page 12).
200A
2 Wire 3 Pole - Style 2
3 Wire 3 Pole - Style 1
3 Wire 4 Pole - Style 2
4 Wire 4 Pole - Style 1
400A
2 Wire 3 Pole - Style 2
3 Wire 3 Pole - Style 1
3 Wire 4 Pole - Style 2
4 Wire 4 Pole - Style 1
RECEPTACLE
PLUG
CORD CONNECTOR
For detailed part numbers and technical information, please refer to section 1P of the Cooper Crouse-Hinds catalog.
9
PowerMate ™ Plugs, Receptacles and Connectors
Grounding
Product Dimensions
Style 1
Receptacle, Plug, Cord Connector
CDR Receptacle
Style 1 units complete the grounding circuit through the metallic plug shell, receptacle housing, or connector shell.
Style 2
CCP Plug†
CRC Cord Connector†
a
b
a
b
a
b
30A
2-7⁄8”
3-3⁄8”
6-1⁄2”
2-5⁄16”
6-3⁄5”
2-9⁄16”
60A 3p
4-1⁄4”
4-1⁄2”
8-1⁄6”
3-5⁄8”
8-3⁄10”
2-5⁄16”
60A 4p
1
4- ⁄4”
4- ⁄2”
1
8- ⁄6”
3- ⁄4”
3
8- ⁄10”
2- ⁄16”
100A 3p
5-1⁄4”
4-1⁄4”
10-4⁄5”
3-3⁄4”
11-1⁄2”
3-3⁄16”
100A 4p
5-1⁄4”
4-1⁄4”
10-4⁄5”
4-1⁄8”
11-1⁄2”
3-7⁄16”
150A (CD)
1
5- ⁄4”
1
4- ⁄4”
10- ⁄5”
1
4- ⁄8”
11- ⁄2”
3-7⁄16”
150A (DE)
5-1⁄4”
4-1⁄4”
10-4⁄5”
4-1⁄8”
11-1⁄2”
3-7⁄16”
a
1
b
4
a
3
b
1
a
5
b
†Dimensions are approximate and vary with cable size.
CEE Back Boxes
Style 2 metallic units with metal housing have a separate designated ground contact that is bonded to the metallic
housing. The metallic housing of the plug, receptacle, or connector forms a parallel ground circuit through the receptacle
or connector detent spring.
Electrical Rating Ranges
• Voltage - 600 VAC, 50 to 400 Hz; 250 VDC*
• Amperes - 30, 60, 100, 150
10
Rating
Size
CEE13
30A
1
a
CEE23
30A
CEE33
⁄2
1- ⁄32”
11
3
⁄4
1-27⁄32”
13
30A
1
1-31⁄32”
15
CEE36
60A
1
2- ⁄16”
15
CEE46
60A
1-1⁄4”
2-5⁄8”
1-3⁄16”
CEE56
60A
1-1⁄2”
2-11⁄16”
1-5⁄16”
9
60A
30A
b
27
⁄16”
⁄16”
⁄16”
⁄16”
CJA
Maximum Horsepower for Plug and Receptacle Combinations by Input Voltage**
The following values are typical horsepower ratings based on NEC Article 430 tables. HP Ratings are based on the
largest conductor size for each plug and receptacle combination per the Wire Size table below.
Ampere Rating Plug
and Receptacle
Cat. No.
Motor Horsepower **
240
Volts
480
Volts
600
Volts
30
15
30
40
60
20
40
50
100
30
60
75
150
40
75
100
200
60
125
150
* This guide is for reference only. Consult your local
electrical codes before installation.
** Cooper Crouse-Hinds recommends circuit breaking
use be limited to emergency conditions only and that
a horsepower rated switch or Cooper Crouse-Hinds
Interlocked Receptacle be used for making and breaking
under load.
With 60, 100 and 150A Angle Adapters
Cat. No.
Hub Size
a
b
c
d
e
f
CJA310
1”
7
5- ⁄8”
8”
7
7- ⁄16”
7
4- ⁄8”
7”
15°
CJA410
1
1- ⁄4”
7
5- ⁄8”
8”
7
7- ⁄16”
7
4- ⁄8”
7”
15°
CJA510
1-1⁄2”
5-7⁄8”
8”
7-7⁄16”
4-7⁄8”
7”
15°
CJA610
2”
5- ⁄8”
8”
8”
4- ⁄8”
7”
15°
7
7
• Back boxes are standard with Corro-Free™ epoxy powder coat finish for increased corrosion resistance.
• Thru-feed back boxes are furnished with one close-up plug in bottom recessed hub.
• CJA back boxes are recommended when additional wiring space is required.
• The angle adapter on CJA back boxes can be installed at 90° rotations, making it possible to enter hub from several
directions.
11
PowerMate ™ Plugs, Receptacles and Connectors
Replacement Parts
PowerMate™ Part Numbers
Standard Replacement Parts
CCP
Replacement Interiors 30, 60, 100, 150A
Complete insulator
and contact assembly
2W2P
2W3P
3W3P
3W4P
4W4P
30A
60A
100A
150A
CRI Receptacle &
Connector Interior
CDR-CRC
CRI-3022
CRI-6022
CRI-1022
---
CCP
CPI-3022
CPI-6022
CPI-1022
---
CDR-CRC
CRI-3023
CRI-6023
CRI-1023
---
CCP
CPI-3023
CPI-6023
CPI-1023
---
CDR-CRC
CRI-3033
CRI-6033
CRI-1033
---
CCP
CPI-3033
CPI-6033
CPI-1033
---
CDR-CRC
CRI-3034
CRI-6034
CRI-1034
CRI-15034
CCP
CPI-3034
CPI-6034
CPI-1034
CPI-10534
CDR-CRC
CRI-3044
CRI-6044
CRI-1044
CRI-15044
CCP
CPI-3044
CPI-6044
CPI-1044
CPI-15044
CPI Plug Interior
Miscellaneous Replacement Parts
Amperage Configuration
Center
Center
CDR
Spring
Cover
CDR
Threaded
Cover
CCP
Fastening
Ring
Bushings Kits
Center
30A
2-pole, 3-pole
4-pole
PTSC30
PTTC30
CLMPR30
PTGB30
60A
2-pole, 3-pole
4-pole
PTSC60A
PTSC60B
PTTC60A
PTTC60B
CLMPR23P60
CLMPR4P60
PTGB60
100A
2-pole, 3-pole
4-pole
PTSC100A
PTSC100B
PTTC100A
PTTC100B
CLMPR23P100
CLMPR4P100
PTGBCD
CLMPR4P150
PTGBCD (CD Size)
PTGBCD (DE Size)
150A
4-pole
PTSC150B
PTTC150B
Spring Cover
Threaded Cover
Diameter of Wire Recess in Plug & Receptacle Contacts
Amperage Rating
Contact Type
Diameter of Recess
Wire Size †† Extra Flex
30 (2, 3, & 4-pole)
Pressure
.281”
#10-#8
60 (2, 3, 4-pole)
Pressure
.312”
#8-#4
100 (2, 3, & 4-pole)
Pressure
.390”
#4-#2
150 (4-pole)
Pressure
.390”
#2-1/O
3
4
BC
RS
PRODUCT TYPE
CCP - Plug
CDR - Receptacle
CRC - Connector
CDRE - Receptacle with CEE Back Box
CDJA - Receptacle with CJA Back Box
AMPERAGE
30 - 30 Amp
60 - 60 Amp
10 - 100 Amp
150 - 150 Amp
(200 & 400 Amp options avail. as part of Arktite Series)*
WIRE
2 - 2-Wire
3 - 3-Wire
4 - 4-Wire
Wire Sizes
The table below lists the diameter of the wire recess in PowerMate plug and receptacle
contacts so that maximum size of bare conductor can be determined. Range of wire
sizes shown in table are intended only as a guide. Depending on type of wire used
(building wire, flexible or extra flexible cable) and its construction (number and size of
strands), bare copper diameters vary widely.
30
Bushing Kit
POLE
2 - 2-Pole
3 - 3-Pole
4 - 4-Pole
CABLE RANGE **
(plug and connector only)
BC - 0.390” to 1.375”
CD - 0.875” to 1.906”
DE - 1.250” to 2.190”
E - 1.875” to 2.500”
F - 2.500” to 3.000”
G - 3.000” to 3.500”
OPTIONS
RS - Reverse Service
P4 - Special Polarity
HUB SIZE***
(receptacle with back box only)
50 - 1⁄2”
75 - 3⁄4”
100 - 1”
125 - 1-1⁄4”
150 - 1-1⁄2”
200 - 2”
250 - 2-1⁄2”
300 - 3”
350 - 3-1⁄2”
400 - 4”
500 - 5”
* Refer to section 1P of the Cooper Crouse-Hinds catalog.
** Cable Range only applies to specific plug part numbers.
*** Hub size only applies to specific receptacle part numbers.
††Do not use wire size smaller than minimum size recommended.
12
13
It’s about knowing your challenges inside out
Plug and Receptacle Solutions for Land-Based Drilling
Drilling Rig Locations
1
Derrick/Mast
2
VFD/Generator(s)
3
Product Photo
Environmental
Conditions
Fuel Tank
1
4
5
Doghouse/
Operator’s House
6
Power/Pump Station
7
Shale Shaker
8
9
10
Industrial
Motor Control/VFD/
SCR House(s)
Areas prone to dust, dirt,
grime, vibration, hard use and
abuse.
Wet Locations
Protection from
wind-blown dust and rain,
splashing and hose-directed
water and external formation
of ice.
Mud Tanks/Pumps
Vibration
Locations that need products
designed to withstand
continuous movement and
may require maintenance and
repair.
Drawworks & Top Drive
Drilling Floor
Corrosive Areas
Protection for areas with
corrosive chemicals,
atmospheres and water.
3
Space Constraints
2
5
4
Areas with low ceilings, tight
spaces and limited footprint
potential.
Class I, Div 1/Zone 1
10
6
9
7
8
Explosion protection for
areas with flammable gases
or vapors normally in the
atmosphere.
Class I, Div 2/Zone 2
Explosion protection for
areas where flammable gases
or vapors are not normally
present.
Class II, Zone 21 & 22
Protection for areas where
ignitable dusts may be
present.
Please refer to your own company documentation for exact specifications and environmental conditions.
14
Product Solutions
Env. Conditions
Rig
Location
PowerMate Series
• Supplies power to portable devices such as motor generator sets, compressors, heating/cooling, welders
and lighting from 30 to 150A
• NEMA 4X copper-free aluminum construction with epoxy powder coat finish is ideal for harsh environments
• Arc-snuffing design enables large power loads to be disconnected under load without an arc flash (up to
100 amps)
• 360° split pin contact reduces heat rise and eliminates arcing
• Lockout/tagout hole in plug to ensure it cannot be inserted into receptacle when maintenance is being
performed downstream
Industrial
Wet Locations
Vibration
Corrosive Areas
Space Constraints
ENR & ENP Series
• Explosionproof outlet for convenience and lighting connections, 20A MAX
• Factory-sealed chamber encloses potential arcing components between two explosionproof threaded
joints
• Frustration-free ENP with captive set screws assures ease of installation and reduces likelihood of losing
critical components in the field
• ENRM4 Series with gasketed screw cap cover offers features that protect interior from harsh environments,
provide time saving saddle clamp terminals, and improved safety with lockout/tagout hole
Industrial
Vibration
Space Constraints
Class I, Div 1/Zone 1
Class I, Div 2/Zone 2
FSQC & EBBR Series
• Interlocked units with dead front receptacles ensure connection cannot be made or broken under load,
increasing safety and protection
• PowerMate plugs can be used with both FSQC (30-60A) & EBBR (30-100A) Series to provide ultimate
flexibility of portable equipment used throughout the rig
• FSQC units are interlocked with switches and the EBBR Series is interlocked with circuit breakers for
added protection
Industrial
Wet Locations
Vibration
Corrosive Areas
Space Constraints
Class I, Div 1/Zone 1
Class I, Div 2/Zone 2
4, 7, 8, 10
CES & CPH Series
• Equipped with a delayed action rotating sleeve which prevents complete withdrawal of CPH plug in one
continuous movement
• The delayed action feature permits the plug to be used as an emergency push-pull switch
• Receptacles are factory sealed to simplify installation and eliminate the need for external seals
• Available in 30 and 60A
• CPH also mates with FSQC, EPC, and EBBR receptacles of matching configuration
Industrial
Wet Locations
Vibration
Corrosive Areas
Space Constraints
Class I, Div 1/Zone 1
Class I, Div 2/Zone 2
7, 8
eXLink® Connectors
• Signal and power connections can be switched under load
• Reduces installation time, providing maintenance and labor savings
• Can be factory installed and pre-wired with Cooper Crouse-Hinds industry leading light fixtures
• Rated up to max. 16A and up to 400V
Industrial
Wet Locations
Vibration
Corrosive Areas
Space Constraints
IEC 309 GHG 51 Series
• Supplies power to portable devices with requirements of 16-125A
• Reinforced polyester construction offers reliability from -20° to +55°C
• Integrated AC3 rated disconnect switch
Wet Locations
Vibration
Corrosive Areas
Class I, Div 2/Zone 2
Roughneck™ Connectors
• For use with single conductor 313-777 MCM cable, 1000 volts AC/DC, rated up to 1135A
• Designed for heavy abuse - resistant to rain, mud and oil
• Quickly connects and disconnects without any tools
• Superior safety protection with totally shielded contacts
• Color-coded insulators for easy identification to prevent reverse phasing in AC and cross polarization in DC
• Mated assemblies are lockout/tagout compatible
Industrial
Wet Locations
Vibration
Corrosive Areas
Space Constraints
Pauluhn™ 80/86/96/wd (NRL) Connectors
• Watertight ANSI NEMA type receptacle
• Accepts standard ANSI NEMA type plugs
• Mating plugs with integral threaded ring maintain a watertight seal
• Available in seven different voltage configurations up to 20A
• Captive threaded receptacle cap
Industrial
Wet Locations
Vibration
Corrosive Areas
Space Constraints
Pauluhn™ PPR Series Connectors
• Watertight non-metallic construction including water shedding receptacle design
• Corrosion and impact resistant closure
• Captive threaded receptacle cap
• 2P3W and 3P4W available in single or double gang types and with an in-line connector set up to 20A
• Double gang receptacle provided with pre-stripped leads
• Inter-mateable with other brands
Industrial
Wet Locations
Corrosive Areas
2, 4, 5
1, 2, 3, 4,
5, 6, 7, 8,
9, 10
1, 10
7, 8, 9
2, 4, 5, 6,
9, 10
1, 2, 4, 5,
7*, 8
2, 4, 5
* On enclosed rigs.
15
For more information:
If further assistance is required, contact your local Cooper Crouse-Hinds Representative. Call customer service at 866-764-5454, or email crouse.customerctr@cooperindustries.com
U.S. (Global Headquarters):
Cooper Crouse-Hinds
Wolf & Seventh North Streets
Syracuse, NY 13221
(866) 764-5454
FAX: (315) 477-5179
FAX Orders Only: (866) 653-0640
crouse.customerctr@cooperindustries.com
Canada:
Cooper Crouse-Hinds Canada
Toll Free: 800-265-0502
FAX: (800) 263-9504
FAX Orders Only: (866) 653-0645
Mexico/Latin America/Caribbean:
Cooper Crouse-Hinds, S.A. de C.V.
52-555-804-4000
FAX: 52-555-804-4020
mxmercadotecnia@cooperindustries.com
Europe (Germany):
Cooper Crouse-Hinds GmbH
49 (0) 6271 806-500
49 (0) 6271 806-476
sales.CCH.de@cooperindustries.com
Middle East (Dubai):
Cooper Crouse-Hinds LLC
971 4 4272500
FAX: 971 4 4298521
Singapore:
Cooper Crouse-Hinds Pte. Ltd.
65-6297-4849
FAX: 65-6297-4819
chsi-sales@cooperindustries.com
China:
Cooper Crouse-Hinds Pte. Ltd.
86-21-2899-3600
FAX: 86-21-2899-4055
cchsales@cooperindustries.com
Australia:
Cooper Electrical Australia
61-2 8787-2777
FAX: 61-2-9609-2342
CEASales@cooperindustries.com
Colombia:
+(57.1) 670 0315
FAX: +(57.1) 670 0376
ventascic@cooperindustries.com
Brazil:
+55 15 3238 3970
FAX: +55 15 3238 3976
vendasbrasil@cooperindustries.com
Saudi Arabia:
966 3 812 2236
FAX: 966 3 812 1291
www.crouse-hinds.com
Cooper Crouse-Hinds is a registered
trademark of Cooper Industries, Ltd.
©2012 Cooper Industries, Ltd.
Your Authorized Cooper Crouse-Hinds Distributor is:
Cooper Industries, Ltd.
600 Travis, Ste. 5800
Houston, TX 77002-1001
P: 713-209-8400
www.cooperindustries.com
5022-0112
Printed in USA