March Issue 2016
Table of Contents
Heat Treat News
Used Equipment
•
•
•
•
•
•
•
•
European
Batch
Continuous
Draw
Generator
Induction
Miscellaneous
Vacuum
Employment Opportunities
Seeking Employment
If you would like the information
contained in this newsletter daily
instead of monthly, visit us at
www.themonty.com
daily & you don’t have to wait for
the most up to date, relevant Heat
Treat News in the industry.
www.themonty.com
Heat Treat News
Letter
Introduction
Best regards,
Gord
www.themonty.com
Our March 2016 issue of “The Monty” includes a wide variety of items about the
worldwide heat treating industry including trends, “people” items, press releases
and even a couple of news items which provoked some rather strong responses.
At the end of the day each and every item you read on “The Monty” has a
common denominator; it has to do with heat treating and we are proud to say
that this will always remain our focus. So send us your press releases,
announcements, photos and thoughts and as long as it is relevant to the industry
we will be glad to work with you.
News
Where are they now? Dick Wagner. We used to spend a great deal of time
with Dick Wagner a manufacturers rep for the heat treating industry who
was based in Indianapolis, Indiana. At differing times he worked with TJ
Wright and Pat Torok representing companies such as AFC-Holcroft and
Wirco. We lost touch with Dick but as it turns out he is happy and healthy
and enjoying retirement. We see that SBS Corp. of Florida has a fairly new Manufacturing
Manager a fellow by the name of Michael Rebula. SBS is best known for their line of air
cooled quench oil coolers.
www.themonty.com
Monday Morning Briefing. Recently we mentioned a fire at commercial heat treater
Advanced Heat Treating in Ridgway, PA. As a follow up to this story we now have a cause
as you can see below. There is no doubt in our minds that water in quench oil and oil build
up in furnace venting are the two major causes of heat treat fires. “RIDGWAY — A fire Feb.
17 at Advanced Heat Treating in St. Marys has been ruled accidental. Ridgway-based state
police said Wednesday the state police fire marshal and Crystal Fire Department (St. Marys)
investigated the fire, which happened at 11:50 p.m. Feb. 17, originating in a gas fueled
heat-treated furnace located in the northeast corner at the rear of the building. Police said an
operator at the furnace pulled a hot metal load and placed the metal into
quench oil used to temper the metal by cooling it down. Upon placing the
metal in the oil, the oil began to react with water that accidentally had been
mixed with the quench oil. This caused the quench oil to spill out of the
furnace and onto the floor, where it caught on fire, police said. The
estimated damage was $750,000. Police said the business did have
insurance”. Thom Coughlin is retiring from the heat treat industry-in case
you don’t know Thom he most recently worked with Plansee USA as Mid
West Sales Manager for 15 years, prior to that worked with Marathon
Monitors (Cincinnati) from 1991 through 2000 Before that he worked with
Ipsen Intl/Surface Combustion and going way back he spent many
years in the Western USA working in hard rock mines as the plant
Metallurgist for various mining companies. Quite an impressive work history.
French vacuum furnace builder B.M.I. has a new rep in Brazil, a fellow by the name of
Milton Machado. While we wish him the best of luck the Brazilian heat treating market is
not one which is exactly thriving these days so we hope he is on salary and not commission.
PhoenixTM whose banner ad can be found on this page sent us this press release.
"PhoenixTM will supply a ‘hot box’ system to a major US & European manufacturer of
aluminum extrusions for the aerospace industry. The system will be engineered to withstand
a full immersion water quench during the solution heat treatment process, and will use 2 x
20 channel data loggers to monitor temperatures throughout the furnace from up to 40
thermocouples. Their aim initially is to be able to gather as much temperature data as
possible during a profiling trial with a view to optimizing the heat treatment operation. In the
future the system may also be used to carry out regular TUS surveys as part of their ongoing
NADCAP accreditation.
www.themonty.com
Down in Mexico we hear that commercial heat treater HT-MX Tratamientos Secundarios
in Chihuahua is adding some more capacity in the form of a couple of used batch IQ
furnaces. HT-MX Tratamientos Secundarios was founded in 2012 as Procesos Térmicos HTMX SAPI de CV. in the city of Chihuahua, Mexico. An organization by the name of
Metalspain seems to regularly hold small heat treating exhibitions around the world with
one coming up in Queretaro, Mexico this year. We have never attended one of these events
and don't know of many people that have but they certainly are an aggressive bunch. A
friend of ours in the industry has now received an e-mailed invite from the organizers 417
times if you can believe it. And we thought the show in Shanghai was bad!
Business Opportunities. "The Monty" has many top notch positions available in the heat
treating industry which indicates both the shortage of good people available and also the fact
that we get results for our advertisers. A small sampling of recent offerings are listed below.
February 29, 2016.
Do you want results when it comes to filling a position within the heat treating industry?
"The Monty" is the most economical, fastest way to fill that position. Looking for a job?
Send us your ad and we will put it on the site free of charge for as long as you would like.
When it comes to filling positions within the heat treating industry "The Monty" can't be
beat. With a readership of over 20,000 heat treaters/month we will help you fill your position
or help you find a job. Just contact jordan@themonty.com.
•
•
•
•
•
Field Service Supervisor
Successful Sales Representative
Heat Treat Operator
Senior Metallurgical Engineer
Quality Manager
SECO/WARWICK. Furnace builder SECO/WARWICK has received a very significant award in
Poland as one of the most dynamic companies in the country. SECO/WARWICK (SWG),
inventor, designer and creator of heat treat solutions has just won a title from The Gazelles
of Business award as one of the most dynamic companies in Poland. This win is another
confirmation of SECO/WARWICK's stable growth, solid global market position and financial
transparency”, says Bartosz Klinowski, President of SECO/WARWICK Europe. To win The
Gazelles of Business a company needs to have a steady increase in sales and financial
stability as well as transparency in accounting followed by external audits for at least 3 years
preceding.
www.themonty.com
And from King Tester we have this item; "King Tester is expanding its product line to
include the full range of Ernst hardness testers. Customers will benefit by having a single
source for a range of Rockwell, Brinell, micro, and in-line hardness testers throughout North
America. King is working with Ernst S.A. Ernst to provide the innovative and highly popular
hardness testers marketed and previously sold by Newage Testing Instruments under
tradenames like Versitron® and AutoBrinell. “With the increasing emphasis on quality of
manufacture we are excited to take this step and broaden our product line with some of the
finest hardness testers available on the market today” said James Knight, president of King
Tester Corporation. “Ernst is a well-known brand and a company with the highest level of
commitment to quality and product integrity and we are pleased to be working closely with
them”, added Knight". February 29, 2016.
Used Equipment Available. New or relatively new additions to our list of used equipment
include these items below. Remember if you don't see what you are looking for please let us
know and we will do our best to find it for you. Feel free to contact us at;
jordan@themonty.com February 29, 2016.
A few examples include:
•
•
•
•
•
•
Georg Fischer Shot Blast System
Surface Combustion (Pifco) Roller Hearth Line
Ipsen Pusher Line P-12
1 Surface Combustion Radiant Tube and 4 supports
Marley NC Cooling Tower
Williams Temper 48x48x36
Bodycote 2015 Preliminary Financial Results. Global commercial heat treater Bodycote
has just announced their Preliminary Results for the year ended 31 December 2015. The
entire report can be found at http://www.bodycote.com/, what you see below are some
“cherry picked” items taken exactly from their report.
Highlights
• Revenue down 4% at constant currency to £567.2m
• Business improvements and restructuring actions mitigated challenging energy and general
industrial markets
• Headline operating margin sustained at 18%
• Capital investment accelerated for future growth
• Net cash of £12.3m
www.themonty.com
The title of The Gazelle of Business has been won a number of times by SECO/WARWICK.
It’s a confirmation of stable growth, investing in development, innovations, technologies and
service of our clients all over the world”, says Bartosz Klinowski, CEO of SECO/WARWICK
Europe. „I believe that a stability of the company can be assessed only after a few or a
dozen of years of operating. Our company have been around for 25 years and during that
time we have reached an international recognition and recognition on the market of heat
treat solutions”, adds Bartosz Klinowski. This year's title is the 9th one in the 25-year history
of the company” summarizes Katarzyna Sawka, SECO/WARWICK Group Marketing Director."
February 29, 2016.
• Final dividend of 10.3p
• Special dividend of 10.0p
STRATEGIC PROGRESS: To enhance our future growth we have accelerated investment in
high growth potential areas, mindful of the Group’s 20% hurdle rate for return on capital
employed. The increase in capital expenditure was driven by the number of greenfield
facilities under construction along with specific capacity expansion in Specialist Technologies
and civil aerospace. Nine greenfield sites were under construction in 2015, of which four are
for Specialist Technologies and three are in the targeted expanding markets of Eastern
Europe, Mexico and China. Additionally, capacity has been expanded at specific existing
Specialist Technologies and civil aerospace facilities. February 26, 2016.
Gas Nitriding Furnace Shipped to Texas. UK furnace manufacturer Thermserve very
recently shipped a gas nitriding furnace to a customer in Texas.
“Thermserve Ltd has shipped a large gas nitriding furnace Texas in the USA. The Gas Nitrider
is to be used for nitriding extrusion dies for extruders around the United States. A gas
nitriding furnace is used to form a very hard surface onto the extrusion dies. Both brand new
dies and used dies are nitrided between each use as they get older. This is normally carried
out a 535C in an ammonia rich atmosphere. Nitriding is initiated
when gaseous ammonia is cracked or “dissociated” using a steel
surface as the catalyst at about 480C. Active nitrogen produced
during this reaction moves into the surface of the steel and combines
with Chromium and other alloy constituents to form their respective
“nitrides”. These nitrides are extremely hard (1200Hv to 1500Hv) and
increase the average hardness of the surface layers of the steel. As a
general rule, the processes will double the (surface) hardness of the
original steel. Thermserve has built and supplied the furnace in
association with RGB Metallurgical Ltd, of Burntwood, UK. Furnace
characteristics include PLC/HMI control for fully automatic operation.
Mass flow control is incorporated for accurate nitriding potential
function; along with an accurate ammonia gas analyser. Multiprogramme recipes are included and the furnace is equipped with fast cooling, hydraulic lid
and complete dissociation control." February 25, 2016.
www.themonty.com
Commenting, Stephen Harris, Group Chief Executive said: “The Group delivered a
resilient performance in 2015. Automotive and aerospace revenues moved ahead. However,
the decline in oil price combined with downward pressures on our general industrial business
led to Group revenues falling by 4% at constant exchange rates. The speed and
effectiveness of management’s actions, in addition to the continued focus on improved mix,
enabled headline operating margins to be sustained. Recognising the Group’s net cash
position, the Board is recommending a further special dividend. The Group will continue to
follow its strategy of investing in areas of robust revenue opportunity, notably in Specialist
Technologies and in higher growth territories, as well as further enriching the mix towards
higher added value services. The Board is confident that management’s continued focus on
business improvements will generate good returns throughout the cycle.”
Derrick Company/Cincinnati, Ohio. Commercial heat treater Derrick Company is getting
into the aluminum processing business, something the company has been looking at for
some time. Derrick Company Inc. Awards Wisconsin Oven Order for New Aluminum Heat
Treating Equipment.
National Heat Treat/Houston, Texas. People are hurting in Texas with oil field suppliers
such as Haliburton and Schlumberger laying off in the thousands but life continues and there
are still some investments being made in the industry. Commercial heat treater National as
an example is within a month of installing a very large Ipsen bottom loading vacuum
furnace. As we speak Mercer Technologies (who is doing the complete top to bottom rebuild
including, new hot zone, controls and pumps) is putting the finishing touches on the furnace.
While this is not a new furnace it is certainly a new one for National (and for all intents and
purposes will be when the rebuild is completed. February 24, 2016.
Bodycote. "Bodycote, the world’s leading provider of heat treating services, held a ground
breaking ceremony for a new aluminum solution treatment capability at its Westminster,
California location in February 2016. With this new capability, Bodycote will be able to
process aluminum alloys up to 21 feet in length at 1100ºF, able to use multiple types of
quench media. This new furnace, scheduled to be in service by the end of third quarter this
year, will allow the treatment of large aerospace and commercial forgings, up to 20,000 lbs.
Bodycote continues to invest in regional aerospace manufacturing markets across the USA in
support of aerospace prime manufacturers and their supply chains." February 24, 2016.
CeraMaterials. "CeraMaterials (Port Jervis, New York) have signed on William G.
Montgomery Limited as their representatives for all of Canada focused on expanding the
customer base in the Canadian heat treat industry. CeraMaterials president, Dr. Jerry
Weinstein issued a statement, "We are very excited to have Gord Jordan Montgomery of
“The Monty”, on board representing CeraMaterials. Both men bring a wealth of experiences
and expertise to our key market areas of heat treating & manufacturing. They have already
brought to us some good opportunities. We look forward to a long and prosperous
relationship with the Montgomery family.” Ceramaterials (www.ceramaterials.com) is an
international supplier of graphite & ceramic Insulation, carbon composites, machined
graphite, ceramics and Moly products mainly for vacuum & process furnace applications in
the heat treat industry." February 24, 2016.
www.themonty.com
"Wisconsin Oven has recently been awarded an order from the Derrick Company, Inc. for a
horizontal quench furnace and industrial batch oven. The Derrick Company is a fifth
generation family owned and operated metal heat treating company located in Cincinnati,
Ohio. For over 90 years the Derrick Company has specialized in processing unique, one of a
kind, very large carbon steel fabrications, weldments, tanks, and vessels, as well as steel
and iron castings. With the addition of the equipment from Wisconsin Oven, Derrick
Company will be adding a new line of aluminum heat treating services that will include
solution treating and aging processes on small to medium size aluminum parts. The order is
scheduled to ship this summer and the Derrick Company’s new aluminum heat treating
services will be available later this year." February 25, 2016.
European Used Equipment Available. For 17 years “The Monty” has been very
successful at putting buyers and sellers of used heat treating equipment together and we
now bring this model to Europe. If you have surplus heat treating equipment we would be
very happy to help you find a buyer on a non-exclusive small commission basis. Please let us
know what questions you have and we will be happy to answer them. If you are a buyer
looking for a particular item please let us know and we should be able to find it for you.
jordan@themonty.com. February 23, 2016.
A few examples include:
•
•
•
•
•
CODERE Multi-Purpose Furnace Line
TAV 6 Bar Vacuum Furnace
JLS Redditch Gas Heated Oven
SOLO Furnace System
SOLO Furnace Line
Solar Manufacturing/ John Oakes. We'd like to welcome John Oakes to
the Solar Sales Team. If you recognize the name it might be because Jim
Oakes, (John's brother) has worked for SSi for a long time.
"Solar Manufacturing is pleased to announce the appointment of John
Oakes as their new sales representative for the Northeast US region. Mr.
Oakes will focus on vacuum furnace sales in Connecticut, Delaware, Maine,
Maryland, Massachusetts, New Hampshire, New Jersey, New York, Rhode
Island and Vermont. Mr. Oakes recently became the owner of the Edward
www.themonty.com
C.I. Hayes, a Gasbarre Furnace Group Company. "C.I. Hayes, a Gasbarre Furnace Group
Company, is please to announce the recent installationg of a Humpback Conveyor Belt
Furnace for brazing of stainless steel parts to be used in the electrical industry. The furnace
operates with low dewpoint hydrogen atmosphere and a maximum operating temperature of
2100 F. The furnace also includes a dewpoint and oxygen monitoring system and
communications that allow for remote login and troubleshooting. Located in Cranston, RI,
C.I. Hayes designs, manufactures and services industrial vacuum and atmosphere heat
treating equipment and has been delivering custom solutions to the heat treating industry
for 109 years." February 23, 2016.
A. Boll Company, Inc. (www.ebco-us.com), a well-known and well respected sales
organization who has been supplying quality products to the thermal processing industry for
over 30 years.
CeraMaterials/ Jeff Opitz. "CeraMaterials is pleased to announce that Jeff Opitz has joined
CeraMaterials as their Technical Sales Specialist in the Port Jervis
headquarters facility. Jeff has a B.A. from the University of Pittsburgh in
Economics and Communications with 10 years of sales & marketing
experience. Jeff honed his sales skills at Metrie (A Sauder Company)
marketing wood & trim products for home construction, Doskocil
Manufacturing focused on the pet product industry and most recently with
Clarion Safety Systems, focused on safety communication systems. Jeff brings
to Ceramaterials much needed sales expertise with strong technical &
marketing abilities and has already contributed to improved sales & extending
the customer base in key market areas of ceramic & graphite insulation. CeraMaterials
(www.ceramaterials.com) is an international supplier of graphite & ceramic insulation,
carbon composites, machined graphite, ceramics and Moly products mainly for vacuum &
process furnace applications." February 23, 2016.
TRW, Lebanon, TN/Outsourcing. Outsourcing is a subject which always provokes a strong
response amongst commercial heat treaters-namely are more manufacturers turning to
commercials as opposed to heat treating in house? Here is an example of an auto parts
maker who has decided to send their product out to be heat treated. TRW in Lebanon,
Tennessee (now ZF) has always done their heat treating in-house in a combination of pusher
and batch IQ furnaces. The company recently made the decision to send all the work out to
commercial heat treaters and completely shut down their rather antiquated heat treat
department. Based on the number of furnaces the company had this is a lot of heat treating
being sent out. February 22, 2016.
Lindberg/MPH. "Lindberg/MPH announced the shipment of an electric immersion aluminum
holding furnace to a large automotive die caster. The equipment provided includes three
electric immersion aluminum holding furnaces used to keep aluminum at die casting
temperature. These aluminum holding furnaces utilize Lindberg/MPH patented board lining
and high efficiency immersion tubes/heaters. A manually operated winch crane operates the
center cover for cleaning. “Repeat business based on past performance is a testament to the
quality and durability of Lindberg/MPH equipment. We work closely with our customers to
provide the best possible solution to their application needs and are pleased to be their
chosen vendor.” Andrew Paul, Sales Engineer Unique features of these aluminum holding
furnaces includes:
www.themonty.com
Pete Reh, Vice President of Sales for Solar Manufacturing, is pleased to have John as part of
the sales team. “We have known John for some time and I have always felt he would be a
valuable addition to our sales team. When the opportunity arose, we were happy to discuss
the real possibility of him joining our rep force. Not only does John possess a long
experience in our industry, but he is also a person of high character and integrity. John will
serve our customers very well.” For more information about Solar Manufacturing visit us at
www.solarmfg.com." February 23, 2016.
•
•
•
•
•
Efficient electric immersion heating.
Excellent temperature control and fast recovery.
Lindberg/MPH patented board lining.
Longer lining life.
Manually operated winch crane cover lift
Wisconsin Oven. "Wisconsin Oven Corporation announced the shipment of two (2) natural
gas fired ultimate duty walk-in batch ovens to a leading aerospace manufacturer for
composite curing of aircrafts. The customer required a compact footprint for the equipment
to maximize use of their available floor space. These two batch ovens were designed for
side-by-side installation to minimize their footprint and use of facility floor space. The walk-in
batch ovens have a maximum operating temperature of 500°F and a work chamber of 10’W
x 35’L x 10’H. The composite curing ovens feature guaranteed temperature uniformity of +/5°F at 120°F and 210°F which was verified through a nine (9) point profile test prior to
shipment. The recirculation systems utilize combination airflow which provides both
horizontal and vertical upward airflow to maximize heating rates and temperature uniformity
of the product. The batch ovens are equipped with two (2) 20,000 CFM @ 15 HP belt-driven
blowers. Supply air is delivered through fully adjustable boxed ducts and side-mounted along
the length on each side of the work chambers. “This customer needed the production
capacity of two ovens but did not have a lot of floor space to spare. Our engineering team
designed a space saving solution in which the ovens could be installed side by side to
minimize the floor area used.” Gene Vetter, Senior Applications Engineer at Wisconsin Oven.
February 22, 2016.
Advanced Heat Treating Fire/St Marys, PA. A heat treat fire always hurts. Anecdotal
stories and formal news reports from PA lead us to believe this was not a bad fire but of
course there is no such thing as a good fire in the industry. St. Marys by the way is a small
town but it is also the heart of the Powdered Metal Industry in North America if you can
believe it. "St. Marys, PA. Crystal Fire Department responded to a structure fire at Advanced
Heat Treating located at 1057 Trout Run Rd. in St. Marys around 11 p.m. Wednesday
evening. Multiple calls were received reporting the fire. Crews reported heavy smoke
www.themonty.com
About Lindberg/MPH. In addition to melting and holding furnaces for nonferrous alloys, Lindberg/MPH is a leading manufacturer of standard and custom
industrial heat treat furnaces, including pit, box, IQ, and belt type for the
ferrous and non-ferrous markets. Lindberg/MPH customers cover a wide range
of industries including aerospace/military, automotive, commercial heat
treating, energy/oil, electronics and the forging markets." February 22,
2016.
showing upon arrival. St. Marys Ambulance was also on scene at the incident. Crews
reported the fire was under control at 11:35 p.m". February 19, 2016.
Hercules Heat Treating Corp./Brooklyn, NY. While this news item concerns zoning
regulations in the NY City area, it certainly caught our attention because it is talking about a
commercial heat treater whom we are reasonably familiar with. Hercules is capable of
processing many types of parts but we know them best as one of the few commercials
around North America capable of processing aerospace landing gear. We dug through our
www.themonty.com
Ipsen. "Ipsen recently shipped a horizontal-loading MetalMaster® vacuum furnace with 2bar gas quenching to a company in the Southwest U.S. for use in manufacturing catalytic
converter products, which are then used by such industries as Aerospace,
Automotive and Power Generation. Ideal for brazing and other high
vacuum applications, this vacuum furnace line performs distinctively well
with thin section parts and lighter pieces. This customized furnace
features a 36" x 36" x 72" (914 mm x 914 mm x 1,829 mm) graphite
work zone with a carbon steel gas distribution plenum and graphite
heating elements, as well as a 3,000-pound (1,361 kg) load capacity. It
operates at temperatures of 1,000 °F to 2,400 °F (538 °C to 1,316 °C)
with ±5 °F (±3 °C) temperature uniformity. The furnace is also equipped
with a 35-inch diffusion pump and Ipsen's CompuVac® controls system.
In addition, this MetalMaster furnace is capable of meeting applicable AMS
2750E requirements and providing tight temperature tolerances with
DigiTrim® controls settings. It also features an open heating element
detection system, as well as offers a specially engineered heat exchanger
and turbine blower that are designed to optimize gas flow for more
efficient cooling. The MetalMaster furnace's design has maintained
ultimate performance and reliability for more than 45 years, with 500+
installations worldwide. It delivers the cleanliness and uniform cooling that
customers request while also providing a cost-effective, versatile and
adaptable vacuum furnace system. MetalMaster furnaces may also be
ordered with several high-productivity options, including specialized
instrumentation, increased pumping capability and material handling systems. To learn more
about
the
unique
features
of
Ipsen's
MetalMaster
furnace,
visit
www.IpsenUSA.com/MetalMaster. February 19, 2016.
photos and found a rather dated photo of Hercules and part of the Rizzo family taken about
7 years ago. Hercules has a mixture of Vaccum, Salt and Aluminum drop bottom furnaces.
February 18, 2016.
Lindberg/MPH. "Riverside, Michigan: Lindberg/MPH offers a light industrial furnace line that
is ideal for smaller-scale operations such as testing facilities, laboratories and small industrial
plants. Like all of the Lindberg/MPH products, these furnaces are designed to maintain
uniform heat distribution by utilizing the latest in heating and insulation technology. The light
industrial furnaces can be used for a variety of applications including but not limited to
annealing, aging, carbon firing, ceramic firing, hardening, sintering, brazing, preheating,
solution treating, and stress relieving. Customers will find many benefits with the light
industrial furnace line. Standard sizes are available which allows for quick delivery and
stackable models are a perfect fit for facilities with limited floor space. Available options
include furnace stands, advanced controls, and quench tanks and baskets. The light
industrial furnace line also comes with the Lindberg/MPH exclusive three-year warranty. This
warranty is one of the longest within the industry today. It provides coverage for all
components less standard wear and tear. In addition, the labor supplied is also warrantied if
there is a defect in workmanship. www.lindbergmph.com" February 18, 2016.
www.themonty.com
“At a cavernous warehouse on the edge of Clinton Hill, Brooklyn, Anthony Rizzo's 50
employees heat and cool parts for airplanes and missiles, dropping them into a 30-foot-deep,
1,600-degree salt bath and in vats of oil, rigging them with wire so they don't warp. Hercules
Heat Treating Corp., which his father started in 1949 as a tool-and-die shop, has annual
revenue of about $12 million. To keep Hercules going another 67 years, Rizzo needs his
industrial zoning and steady supply of skilled labor. What he does not need is a glitzy
streetcar route designed to jack up property taxes on the formerly gritty waterfronts of north
Brooklyn and Queens. If the pressure [on property owners] to sell is there, then the pressure
to change the zoning becomes a problem. That is what the de Blasio administration proposed
last month, spurred by the gentrification of the areas and developers there. The city plans to
fund the $2.5 billion project with the increased tax revenue it would generate by raising
property values. "I don't see the benefit to us, really, as industry," Rizzo said. "The thing
that would worry me is if the pressure [on property owners] to sell is there, and then the
pressure to change the zoning becomes a problem."
"In October 2015, Ultra Electronics completed the acquisition of Furnace Parts LLC. Ultra
plans to integrate the Furnace Parts business with its existing temperature measurement
business, Ultra Electronics, Nuclear Sensor & Process Instrumentation (formerly known as
Weed Instrument Company) in Round Rock, TX. Operationally for Furnace Parts, products
continue to be produced and shipped out of our Cleveland, Ohio facility, and our
knowledgeable associates will remain with the business, servicing our ever expanding
customer base. Our dedication to providing industrial thermocouples and temperature
sensors of exceptional quality, shipped in the shortest lead times in the industry and with an
emphasis on value remains a constant. Under new ownership, we will continue to enhance
those capabilities and expand the solutions that challenge temperature measurement
applications."
Wisconsin Oven. Now isn't this a really weird but interesting style of oven? It is the first
one of this style that we have ever seen but it looks rather cool-brought to you by Wisconsin
Oven.
"Wisconsin Oven Corporation announced the shipment of a natural gas fired carousel oven
used to cure urethane in molds. This carousel conveyor oven provides a single load/unload
point for the operator. The industrial oven has a maximum operating temperature rating of
275° F and a carousel conveying system that is 30" wide with and outside diameter of 144".
The design capability of the conveyor oven is based on holding various mold quantities and
sizes on the carousel. The carousel has been designed to support 1,500 pounds and has an
adjustable rotation speed of 2 to 10 revolutions per hour. The heater has been sized for
product loading of 1,000 pounds per hour. A powered air seal curtain at each oven entrance
reduces heat loss." February 17, 2016.
www.themonty.com
Furnace Parts LLC. Earlier this week we had a brief news item about industry supplier
Furnace Parts out of Cleveland so it is rather unusual that we should have a second news
item about the company the same week.
HTSU/PhoenixTM. The big name for data-loggers in the industry has always been Datapaq
but this seems to be changing quickly with companies such as Phoenix rapidly growing
market share. February 17, 2016.
PhoenixTM ‘hot box’ system for high temperature TUS
Solar Atmospheres. According to this press release commercial heat treater Solar is
helping out in the very niche area of Hot Isostatic Pressing (or HIPing). February 16, 2016.
"With the escalation of Additive Manufactured components being printed, and the increased
production of engine blade manufacturing to support newer more efficient aircraft, Hot
Isostatic Pressing (HIPing) is in more demand for the densification of many materials. Over
the years, Solar Atmospheres and Pressure Technology, Inc. have mutually understood their
complimentary synergies between the two companies. As an added value service, parts that
require heat treat processing after HIP will be picked up by Solar from the PTI Concord, Ohio
facility at no charge. Michael Johnson, Sales Manager for Solar’s Hermitage, PA facility,
states, “As both vacuum heat treating and HIPing are gaining popularity, by providing the
customer with both state-of-the-art services as one, we can offer quicker turnaround time
and savings on shipping costs.” For more information about Solar Atmospheres contact
Michael Johnson at mike@solarwpa.com
www.themonty.com
"Heat Treating Services Unlimited Inc. (HTSU), a leading US supplier of pyrometry and
Refractory services, has recently ordered a PhoenixTM ‘hot box’ system for performing
temperature uniformity surveys at their client’s plants. The system will use special high
temperature insulation to protect the 10 channel data logger, and RF telemetry will transmit
the TUS data out of the furnace to PhoenixTM ‘Thermal View Survey’ software which will
guide the technician through the process and collate the TUS report in compliance with
AMS2750 and AIGA CQI-9 specifications. “HTSU has worked with multiple In-furnace
systems in the past. We selected the PhoenixTM because of the ease of use, construction,
accuracy and dependability that they are best known for. Our Clients depend on us to keep
them in compliance and with the addition of this unit we will be able to surpass their
expectations” said HTSU President Kyle Favors. HTSU has five locations throughout the US
with customers in 30+ states and 5 countries. For more information visit
www.phoenixtm.com and www.HTSU.com To see video of PhoenixTM system surveying go
to: https://www.youtube.com/watch?v=Ff2QaRKdmHY"
Monday Morning Briefing. Stacy Harley who was Design Project Manager with alloy
company North American Cronite recently moved over to another alloy company, Alcon
Industries of Cleveland where his title is Design Engineer. Both
companies are in the Cleveland area which makes for an easy move.
Jimmy Morris who is well known fellow in the heat treating industry
recently parted ways with industry supplier Furnace Parts LLC of
Cleveland (seems to be a Cleveland day). Jimmy has been in the heat
treating business for many years doing such things as sales, installs and
calibrations. We all tend to think of the downturn in the oil and gas
industries to be a Texas or Alberta story but the ramifications stretch far
from these areas. We mentioned last week about a company in PA which
supplies components to these industries which is on the brink of closing
down. Bob Hill of Solar Atmospheres tells us what he is seeing in PA. "I
hope all is well for you. I read today's Monty regarding Ipsco and wanted
to mention to you that the western PA and north eastern Ohio areas were
truly a boom for oil and gas exploration. The shale formation that they
were successfully fracking is affectionately known as the Utica Shale. It is
estimated this rich reserve along with newer drilling methods could supply
every American's need for energy for many many decades. This area was
very active in this business until the oil prices plummeted. Today the oil
workers have capped the wells and have gone back to Oklahoma and
Texas. Restaurants and hotels that used to be full are suffering. This is why
companies affiliated with O&G like Ipsco and Parker Hannifin are closing
their doors. I am sure we would all gladly pay $3.50 per gallon at the gas
pumps again rather than lose these kind of manufacturing jobs forever".
Where are they now? From time to time at a readers request we play the “where are they
now game and see if we can locate a particular individual. A good friend asked if we could
change this slightly to find a manual. "I am looking for an owner’s manual and operating
instructions for a CVC Model PMC-32 35" diffusion pump. Could you please ask your
www.themonty.com
SSI/Southern Thermal Systems, Heat Treat Seminar. "Super Systems Inc. and
Southern Thermal Systems are pleased to present a seminar for the heat treating industry.
Topics include CQI-9, AMS 2750 E, NADCAP audit findings, and atmosphere troubleshooting.
The seminars will take place on March 16th, 2016 in Arlington, TX at the Hilton
Arlington Hotel. The seminar is $60 per person. To register, click here or call 513-7720060." February 16, 2016.
Consolidated Engineering Co. (CEC) down in Kennesaw, Ga., received an order for a fourzone gas-fired chain conveyor solution furnace. The furnace will be used for the T4 treatment
of high-pressure die castings and will be installed in a casting location in Mexico. The parts to
be heat treated are automobile shock towers. The line includes a solution furnace, air
quench, age oven, cooling unit and four load/unload gantry cranes. It will process the
castings at a rate of 90 per hour. A reader sent us this photo of a captive heat treat down in
Texas. AFGlobal is an enormous company with a number of different manufacturing
locations around the world. One of their locations in Texas supplies components to the oil
and gas industry and this picture shows part of their heat treat department, in this case
what you see are 30,000 pound capacity box furnaces with associated quenching capability.
www.themonty.com
readers for suggestions? Thanks, Bob". If anybody out there can help we would appreciate
hearing about it. In the UK we have this from commercial heat treater Wallwork. "The
Wallwork Group return to trade show MACH with a greater breadth and depth of heat
treatment and coating services to meet the exacting demands of modern engineering. In
addition to expanding capacity through investing in buildings, plant, new processes and
accreditations, the company has increased load size capability – in terms of both individual
component size or batch quantity. Vacuum brazing has been expanded substantially with a
new workshop in Manchester and a doubling in the size of the Cambridge unit. With
additional Nitride hardening facilities the company is one of only a few in the UK able to offer
salt, gas and plasma processes to provide the best technical result for each situation.
Aerospace processing of aluminium and magnesium components has also been greatly
expanded. Wallwork Birmingham is the company centre for the processing of large
components or bulk batches. The site houses modern vacuum heat treatment furnaces with
capacities of four tonnes. A new high capacity Nitrider will come into service in 2016.
Supporting these developments the company has installed the latest solvent spray/vapour
de-grease washer". The photo below shows a part of the company’s operations.
Brazil/Heat Treatment Process Seminar. If you have an interest in the Brazilian heat
treating market this story about an upcoming show in the country will be of interest. Brazil is
a very large market for captive and commercial heat treating with every single form of state
of the art heat treating processing available. Unfortunately the economy is hurting big time
with little relief on the horizon. As an added bonus to this show we see that well known
Janusz Kowalewski formerly of SECO/WARWICK, AFC-Holcroft and ALD Dynatech will be
hosting a video seminar at the event. February 15, 2016.
"The Brazilian Learning Group works with events in the area of thermal processing and will
hold the 3rd. Heat Treatment Processes Seminar on 17 and 18 March in Sorocaba (SP),
Brazil. The most important names in the area of heat treatment of the country will be
presenting speeches on topics such as FMEA, 4D Quenching, Induction Heating, HT
simulation software, CQI9, distortions, atmosphere, quenching, etc and of course news in HT
www.themonty.com
And to round things out we have this news press release from Aichelin Unitherm India.
"Aichelin Unitherm India, a JV company of AICHELIN Group and one of the
leading manufacturers of heat treatment furnaces in India, has received an
order from Hirschvogel Components India for the supply of a special double
decker roller hearth furnace line for isothermal annealing, normalizing and
stress relieving for cold forged shafts and billets. The furnace line has been
specially designed jointly with AICHELIN group companies in Austria and
China, with the low temperature furnace mounted as double deck on the
high temperature furnace to utilize vertical space, with a maximum
throughput of 1800 kg/hr. The furnace line is fully automatic from loading
till unloading of parts in the customer’s trays and will be manufactured
using only electrical components in compliance with CE standards and
safety features equivalent to European standards and will meet the
requirements of CQI 9 and AMS 2750 D. The furnace plant will be executed
on turnkey basis and is expected to start producing by June 2016. About
Unitherm; Aichelin Unitherm a Joint Venture Company founded in 2010, is
one of the technology leaders in the manufacturing of high quality industrial
equipment and systems for thermal and thermo-chemical heat treatment of
metallic components and employs 100 people. Each of our systems is
tailored to individual customer requirements. Our product range is
complemented by cleaning equipment "Flexiclean", gas generators "Endomat" and the
process control system "FOCOS" for the entire line. A broad-based after-sales service at 4
regions in India provides our customers with spare parts and other services, such as
conversions, customer training and much more". February 15, 2016.
GKN Aerospace/Orangeburg County, SC. Aerospace company GKN down in South
Carolina, USA is expanding their location, specifically the company is raising the roof and
enlarging the pits and the reason for this is to acommodate a massive aluminum drop
bottom oven.
“GKN raised the roof of its second plant in the Orangeburg County/City
Industrial Park to about 56 feet and expanded its digging pits about 20 feet
deep. A lip skin is a part of the pod-like structure that houses the aircraft’s
engine. Lip skins aim to provide the aircraft with better engine fuel economy
and reduce engine noise to meet increasingly stringent airport noise
regulations. "We are excited about the opportunity for GKN to have a
second facility," said Gregg Robinson, Orangeburg County Development
Commission executive director. “A variance was granted for the building to
go to this site, and we are excited to have inlet lip skins manufactured in
Orangeburg for Boeing,” Robinson said. The process at the Orangeburg
plant will be vertically integrated, allowing for incoming material receipt,
spin forming, machining, heat treating, chemical processing and all
inspection, certification and shipping. As part of the manufacture of the lip
skin, the product has to be heated to about 1,000 degrees Fahrenheit and
then cooled in a bath for a short period of time. The company announced in
June that it would invest more than $20 million in a new manufacturing
facility adjacent to its existing plant at the intersection of U.S. 301 and
Interstate 26. First-part production from the building is scheduled in late
2016.GKN announced in 2011 it was investing $38 million in its initial plant
at the park. This plant, which manufactures HondaJet fuselages, employs about 60”.
February 12, 2016.
www.themonty.com
processes. On the program is also planned visit to the heat treatment shop of a subsidiary of
the German company ZF located in Sorocaba. In the Industry 4.0 speech, is confirmed the
participation of Janusz Kowalewski in a video conference system. Learning Group (Grupo
Aprenda) is part of the company which publishes Industrial Heating and FORGE magazines in
Brazil and foresees to promote also for this year: 3rd. Brazilian Course of Maintenance and
Safety in Industrial Furnaces - June in Valinhos (SP) 1st. Brazilian Induction Melting Seminar
- July in Osasco (SP) 3rd. Heat Treatment and Metallography Introduction Course - August in
Valinhos (SP) 1st. Electric Power Management Seminar - September in Sorocaba (SP) 2nd.
Heat Treatment and Metallography Practical Course - November in Santa Barbara d`Oeste
(SP) 4th. Forging Technology Seminar - December in Valinhos (SP) Special Highlight for the
participation via Skype of Janusz Kovalesky with the theme Industry 4.0."
“A total of 250 employees will be laid off from Eaton Corporation,
company officials told KETV NewsWatch 7 on Thursday. Jim Michels, the
business communications manager for Eaton, says Eaton notified
employees Thursday that the company was making changes in its
transmission manufacturing facility. Michels says Eaton will move
assembly, gear and shaft machining operations out of Shenandoah, while
retaining machining of some components called "enclosures." The
transition will result in 250 jobs cut in "six months or less" sources say.
Eighty-five jobs will be retained to support ongoing operations. "Basically
just 80 people are left," said the anonymous employee. "We've had
upwards of 1,000 people in the past. In December, we let 70-plus people
go. We were then down to 330. This will take us down to 80." Michels said
that Eaton Corporation has 14 facilities in North America that support
commercial vehicles and automotive vehicles. The company saw changes
in the commercial vehicle industry, which prompted the decision to cut
250 employees, according to Michels. "Two of the manufacturers of
trucks, years ago, made a strategic decision to go to a strategy where
they make their own transmissions and engines," said Michels. "Another
reason is that the market has been moving from manual transmissions to automated -- and
the acceleration of that, within the marketplace, has gone much faster than anyone
anticipated." February 11, 2016.
HTS And IFHTSE. "The ASM Heat Treating Society (HTS) and the International Federation
of Heat Treatment and Surface Engineering (IFHTSE) have partnered to hold the 23rd
iteration of the IFHTSE Congress, an exciting global event focused on thermal processing,
heat treating and surface engineering. This show will take place this April in Savannah,
Georgia, a scenic location expected to draw attendees and exhibitors alike for record
attendance. The technical program is live for this show, and registration is open to the
public. Registration for this event includes a three-day technical program, a welcome
reception with exhibitors, a Wednesday evening dinner, dedicated networking times with
exhibitors and access to the online conference proceedings. The technical program will bring
together international experts from around the globe to present on innovations and research
in thermal processing and surface engineering. More than 125 technical sessions will be
offered over the course of three days, including a special symposium on residual stress.
www.themonty.com
Eaton Corp./Shenandoah, Iowa. This news item is of interest to us because this Eaton
location includes a large captive heat treat department which along with
the assembly operations will shortly be closed. The production from this
location will most likely be moved to San Luis Potosí in Mexico.
HTSU. We are pleased to welcome our newest advertiser HTSU. You can find their ad on this
page. From pyrometry to refractory, burner tuning to energy management, HTSU offers
smart, safe and sustainable solutions to customers worldwide. February 11, 2016.
Heat Treatment Australia Adds 25 Bar Capacity. "Heat Treatment Australia selected
SECO/WARWICK Europe as their supplier for a FineCarb™ LPC vacuum furnace with 25 bar
High Pressure Gas Quench (HPGQ), and two Vacuum Aluminum Braze furnaces. To complete
the heat treat cell, SECO/WARWICK Europe will supply two nitrogen/air
tempering furnaces. The 25 Bar HPQ and one vacuum brazing system will
be shipped to their Brisbane, Australia facility and the second vacuum
brazing system will be located in their new Los Angeles, California facility.
According the Heat Treatment Australia President, Norm Tucker, “I
purchased the first furnace from SECO/WARWICK, a 15 Bar, in 2007 and
was impressed with the quality of the equipment and the support we
received from SECO/WARWICK Europe. When we decided to expand our
operations both in Australia and open our new facility in Los Angeles,
California, SECO/WARWICK had the right combination of quality, service
and new technology.” According to SECO/WARWICK Group Vice President,
Maciej Korecki, “We are pleased to continue our ongoing partnership with
Heat Treatment Australia and support their expansion to serve the
aerospace industry with the latest technology in vacuum brazing and high
pressure quench capabilities.” Vacuum Brazing Furnaces for Aerospace.
The two 2.0VP-4045/48HVS type furnaces will be designed for the
vacuum aluminum brazing process. The furnaces are equipped with a
stainless heating chamber and six temperature control zones in order to
guarantee temperature uniformity within +/-3°C as required by
AMS2750E class 1. Both furnaces will be equipped with a diffusion pump,
and a working zone that can accommodate loads with dimensions up to
900 mm (36 inches) wide x 700 mm (28 inches) high x 1200 mm long
(48 inches1).
25 Bar High Pressure Quench. For over 20 years, SECO/WARWICK has pioneered high
pressure quench technology in the 20 Bar and above category. The 25.0VPT-4035/36NIQ –
a 25 bar VPT-series furnace will be equipped with convection heating, low pressure
carburizing, ability of high pressure gas quenching with Argon and Nitrogen with pressures
up to 25 bar. The furnace will meet AMS2750E Class 2 requirements with instrumentation
type A. It will be used to heat treat aerospace parts at Brisbane facility. Working zone
dimensions are 600 mm (24 inches) high x 600 mm (24 inches) wide x 900 mm (36 inches1)
long and it can accommodate up to 600kg (1300 pound1) loads. About Heat Treatment
Australia (HTA). Winner of the Metal Treating Institute’s (MTI) prestigious 2015 Heat Treater
www.themonty.com
Keynote speakers booked for the 23rd IFHTSE Congress include Prof. H.K.D., H. Bhadeshia,
University of Cambridge talking on “Very Short and Very Long Heat-Treatments in the
Processing of Steel.” Also appearing will be Mr. Toby Steiner covering “Alloying Element
Nitride Development in Ferritic Fe-based Materials upon Nitriding” and finally Prof. Dr.-Ing.
habil. Rolf Zenker who will speak on “Surface Treatment by Electron Beam in Combination
with Other Heat Treatment Technologies” Attendees will have many opportunities to learn
about surface engineering developments and network with industry peers. Conference
organizer Dr. Scott Mackenzie, Metallurgy Research Scientist at Houghton Int ernational,
says “Working closely with IFHTSE, we are poised to have a truly exemplary show. This
congress will be a great opportunity for anyone who is looking to increase their knowledge
about these topics. We have amassed a fantastic program from some of the brightest minds
in the field, and the exhibit will feature top companies.“ To register for this show, visit
www.asminternational.org/ifhtse." February 11, 2016.
Pyradia. “At the end of 2015, Pyradia had the pleasure to welcome Mr Sheng Li of Shanghai
Advanced Material Technology Co. Ltd., at its St-Hubert manufacturing facilities, to discuss
the beginning of a partnership between both our companies. SAMT already offers an
impressive range of high quality vacuum furnaces as well as material testing services , in
Shanghai, China. This new partnership will enable Pyradia to offer high quality heat treating
furnaces such as drop bottom ovens for aluminum heat treating to companies in China. In
December a contract for 2 drop bottom furnaces and 5 ageing ovens has already been
awarded to Shanghai Advanced Material Technology Co. Ltd by an automotive parts
manufacturer for the heat treatment of suspension parts.” February 10, 2016.
Buehler Canada Closes Their Doors. Lab equipment company Buehler, based out of
Canada, recently closed up shop. After a 38+ year career as General Manager at Buehler
Canada, Richard Blackwell has recently joined up with Precision Surfaces International, Inc.,
as the Applications Specialist in Canada. Richard’s responsibilities include: sales, service and
technical support for PSI instruments and consumables. Precision Surfaces International,
headquartered in Houston, Texas. is an international supplier of consumable products and
www.themonty.com
of the year award, given in partnership with Industrial Heating Magazine, HTA was
recognized on November 12, 2015 as the MTI member who has demonstrated a level of
excellence in quality programs, pollution/hazardous waste control, and community
involvement/leadership. HTA is an innovative company that provides solutions for a broad
range of heat-treating needs and is the largest commercial heat treater in Australia. HTA is
the only aerospace heat treater in Australia with AS9100 and Nadcap accreditations. With
over 30 years' practical experience, HTA provides a highly advanced manufacturing
capability in the Australian marketplace. Learn more at www.heat.com.au" February 10,
2016.
preparation equipment used for achieving precision surfaces. These include products for
Metallography, Industrial Superfinishing, Fiber Optic Termination Polishing and 3M
Microfinishing Products. February 9, 2016.
C.I. Hayes, a Gasbarre Furnace Group Company. "C.I. Hayes, a Gasbarre Furnace Group
Company, is pleased to announce the recent installation of a Model BA-M Atmosphere Pusher
Furnace for brazing and general heat treating of stainless steel materials by a dedicated
processor of select cutlery product lines. This is the third C.I. Hayes furnace in use by this
customer. The furnace is equipped with a rigid chain indexing drive, silicon carbide heating
elements and a controlled atmosphere system that includes an analyzer for dewpoint and
oxygen level monitoring plus purge verification. The furnace design has a maximum
operating temperature of 2100°F (1148°C). For automatic load and unload queuing of work,
the furnace is complete with a powered roll return conveyance system with right angle
transfers. Located in Cranston, RI, C.I. Hayes designs, manufactures and services industrial
vacuum and atmosphere heat treating equipment and has been delivering custom solutions
to the heat treating industry for 109 years.
For more information on how C.I. Hayes can provide custom-engineered solutions for your
specific thermal heating requirements and manufactured heat-treating equipment today,
contact Matt Marzullo at 401.467.5200 or mmarzullo@gasbarre.com. Visit our websites at
www.cihayes.com or www.gasbarrefurnacegroup.com for additional information." February
9, 2016.
www.themonty.com
"It is a pleasure to inform you, I am now representing Precision Surfaces
International, Inc. (PSI) as the Applications Specialist for Canada. In this
role, I am responsible for sales, service and technical support for PSI
instruments and consumables. Precision Surfaces International is
headquartered in Houston, Texas. We are an international supplier of
consumable products and preparation equipment used for achieving
precision surfaces. These include products for Metallography, Industrial
Superfinishing, Fiber Optic Termination Polishing and 3M Microfinishing
Products in consumer quantities. PSI has been in business since 1983.
Our entrepreneurial philosophy is to do business the "old fashioned way":
person to person with extensive product knowledge and service beyond
what our customers expect. PSI is a strong supporter of materials
engineering education through our affiliation with ASM International, the
International Metallographic Society (IMS) and the ASM Materials
Education Foundation. We at PSI take pride in sharing a philosophy of
giving back to our industry. Among our team members we boast two ASM
Fellows (FASM) and two IMS Past Presidents. My own career in the
engineering materials field spans for over 40 years: including working in a
metallography / mechanical testing lab, followed by my long career in
technical support and sales of metallographic instruments, microscopes
and hardness testers. My personal business philosophy is a great match
with that of PSI. I have always taken pride in my customer relationships,
providing technical sales expertise on a person-to-person basis. I look forward to continuing
this relationship in the future. My Canadian coordinates are listed below. I would be happy to
send you a copy of our Metallographic catalogue. I am at your service . . . Yours truly,
Richard Blackwell, C.E.T., ASM, Applications Specialist," rickblackwell@psidragon.com
Kern Liebers/Rohde GmbH. "Queretaro, Mexico is one of the fastest growing areas in the
world when it comes to heat treating and that is where this news item comes from. Rohde
GmbH of Germany http://www.rohdetherm.de has successfully carried out the installation of
a chamber furnace for gas nitriding at the Kern Liebers plant in Queretaro, Mexico. The
brand new installation can be seen below. The photo shows from left to right: Emmanuel
Cabrera, Fabian Mutschler, Mark Brennan-Whitmore (Rohde GmbH), Christian Suhling,
Michael Rott (Rohde GmbH), Gabriela Meza, Manuel Valenzuela, Daniel Alber, Luis Perez,
Marco Rodriguez and Ali Ahumada." February 8, 2016.
IPSCO. The downturn in the oil and gas industry has put a major hurt on heat treating not
only in areas such as Texas and Louisiana but all over North America and the world for that
matter. We have this example from Ohio which is not known as a region which would be
effected by the drop in oil prices.
“The oil and gas downturn caught up with TMK IPSCO in Brookfield, Ohio this past week as
employees learned the pipe-threading mill could close in two months unless market
conditions greatly improve. TMK IPSCO is the latest manufacturer in the Mahoning Valley to
www.themonty.com
Marty Benegalia Joins Solar Manufacturing. "Solar Manufacturing is
pleased to announce that Marty Benegalia, President of Southern Thermal
Systems, will assume the role of a sales representative focusing on the
areas in Texas, Oklahoma, Kansas, Arkansas, and Louisiana. Marty joins
Solar Manufacturing with a technical background of 20 years in metallurgy
and heat treating as well as experience in the petrochemical and oilfield
equipment industries. In making this announcement, Pete Reh, VP of Sales
remarked, “Marty brings a wealth of experience to our Sales Team. He is
well known in the industry and his customers have confidence in him. And
being centrally located in Granbury, Texas in the Dallas-Fort Worth area,
Marty will continue to serve this region of the country well for Solar Manufacturing.” Marty
added, “The vast technical and process expertise that Solar offers to our industry is truly
unequaled. The diverse product offerings and outstanding quality of manufacturing makes
this new partnership truly exciting for our company.” For more information about Solar
Manufacturing, please contact Pete Reh at 267-384-5040 x1509, or via email
pete@solarmfg.com and visit us at www.solarmfg.com." February 9, 2016.
ALD. Earlier this week we told you how ALD of Hanau, Germany had
bought out their partner in North America, AFC-Holcroft. We asked the
President and CEO of AFC-Holcroft for his thoughts. February 5, 2016.
"What I can add to the official AMG press release is that we have enjoyed
more than 10 years as partners with ALD, growing the ALD-Holcroft
presence in the North American Market. It has been exciting being
involved with the cycle of vacuum carburizing and gas quench technology.
It has been a great experience and success for both ALD and AFCHolcroft. We had objectives when we started many years ago and the
Team at ALD-Holcroft has done a great job meeting and exceeding the
goals. Although we will miss having Jason Sisler (President of ALDHolcroft) and his team in our building day to day, we understand ALD's
desire and need to make these changes in the organization to align with
their corporate strategies.
We have grown many professional and
personal relationships with the folks at ALD in Germany as well as the ALDHolcroft team in Wixom and I am sure that those relationships will
continue. This is a planned and organized change with coordinated efforts
from both ALD and AFC-Holcroft to make the transition as smooth as
possible. With regard to AFC-Holcroft, the joint venture has long operated
as a separate entity so business will continue as always with our focus remaining more on
the atmosphere side of heat treatment equipment. We have several interesting new
products and technologies coming down the pipeline that I believe will interest the
marketplace. We have had a significant focus on new technology development as we have
approached and entered 2016, the 100th Anniversary of AFC-Holcroft. I am excited about
the future for AFC-Holcroft and our industry."
Bodycote. "As part of Bodycote’s international brazing network, the Stockport, UK plant is
recognised as a centre of excellence for vacuum brazing honeycomb seal components for
both aerospace and power generation applications. To meet growing requirements from civil
aerospace engine manufacturers, power generation OEMs and their supply chains, the
brazing department has been enlarged, new welding and inspection equipment has been
installed, and new vacuum brazing capacity has been added.
www.themonty.com
suffer the collapse of demand from companies drilling for oil and gas in the nation’s shale
plays. And like Vallourec and Exterran, the opening of TMK’s plant here in 2010 was heralded
as indicative of the shale-drilling boom. By November 2011, TMK was running “pretty much”
around the clock, said its president, as the plant hosted a news crew from CNBC preparing a
report on the resurgence of manufacturing in the Midwest. TMK IPSCO manufacturers oil
country tubular goods, or OCTG, used in oil and natural gas exploration. The Brookfield plant
makes threaded connections and then adds them to pipe produced at TMK plants in Koppel,
Pa., and processed in Ambridge, Pa. TMK IPSCO is a division of OAO TMK, Russia’s largest
manufacturer and of steel pipes and one of “the global top-three pipe producers,” according
to the company’s website. Worldwide more than 258,000 workers lost their jobs in 2015 as a
result of rock-bottom oil prices, according to industry consultant Graves & Co., and more job
losses are expected this year”. February 8, 2016.
Ipsen. "When working with vacuum heat-treating systems, a number of maintenance
questions can arise. One of Ipsen’s most common Ask an Expert questions
(www.IpsenUSA.com/Ask-An-Expert) concerns finding leaks and their effect on the process
and furnace. The newest post in Ipsen’s Finding Leaks in Your Vacuum Furnace blog series
takes a close look at how to determine whether the furnace or the pumping system is the
root cause of any vacuum-related issues. Oftentimes, one might immediately assume there
is something wrong with the furnace when it begins to present signs of outgassing, dirty
parts, performance issues, etc. While it’s possible that the furnace could be the source of the
problem, it is important to avoid wasting valuable time going through all the steps of leak
checking the furnace only to realize there’s actually something wrong with the capabilities
and performance of the pumping system. As such, Ipsen experts outlined a few simple steps
for determining whether the furnace or the pumping system is the guilty party in their
newest Finding Leaks in Your Vacuum Furnace blog post; find out what these steps are at
http://bit.ly/LeakCheck-10.” Ipsen’s blog, The Ipsen, Harold, also features informative
videos, expert tips, throwback photos and useful resources, such as A Daily Checklist for
Preventive Maintenance and their ongoing series, A Look Inside the Furnace (which examines
hot zone types, best practices and maintenance). Focused on sharing tips of the trade, as
well as breaking down technical and complex material, this blog provides readers with
valuable, up-to-date thermal processing information. When it comes to valuable resources,
Ipsen is your partner in success. February 5, 2016.
www.themonty.com
When it comes to safety critical components, Bodycote’s Stockport plant
has over 50 years of brazing heritage, from brazing Concorde’s heat
exchangers to abradable felt-metal seals for modern wide body aircraft.
Bodycote was one of the first subcontract heat treatment companies to
provide metal joining services to industry, and has extensive experience in
every generation of material including the latest single crystal alloys and
super alloys. Honeycomb brazing is used to join critical honeycomb seals
in jet engines, essential to the efficiency of gas flow through the engine.
Brazing is a cost-effective process that eliminates the risks associated with
standard welding. Brazing can be used to repair surfaces that are
susceptible to corrosion, erosion and cracking. As demand increases for
improved aircraft engine performance, the use of vacuum brazed feltmetal abradable seals is increasingly being adopted by major gas turbine
manufacturers for flow path efficiency improvements. Bodycote’s vacuum
brazed felt-metal seals provide superior clearance control in blade tip and
labyrinth seal applications up to 760˚C, while minimising or eliminating
wear on expensive rotating parts. Technical customer service is extremely
important for brazing projects, and Bodycote’s engineers around the globe
have the required knowledge and experience to advise customers from
design to brazing manufacture. Bodycote operates brazing centres of
excellence throughout Europe and North America. As a quality-led and
customer-focused business, Bodycote has repeatedly been awarded
Nadcap accreditation for heat treatment, brazing and Electron Beam Welding." February 5,
2016.
Ipsen Insights. "One of the newest things we are working on here at Ipsen is our
PdMetrics™ advanced predictive maintenance software platform. As you can probably tell,
we are extremely excited about being able to offer this product to our customers. It’s already
available as a retrofit or with the purchase of a new furnace. In addition, it functions as a
furnace add-on that is not integrated with the furnace PLC, meaning we can easily and
quickly retrofit it to the global installed base, including non-Ipsen brand furnaces. One of the
things that our customers in the heat treatment industry mention is that they are always
looking for ways to reduce unplanned downtime and unexpected costs. Now, imagine that
your furnace has the ability to notify you before it needs maintenance, or if some other
actions are required. Imagine you have a tool that allows you to anticipate disruption; a tool
that gives you the power to optimize equipment performance and production efficiency. This
is what the PdMetrics software platform does – it offers the power of possibilities. Building
upon your existing maintenance and PM programs, it provides an automatic maintenance
reminder that is based on how your furnace is performing. For example, rather than
replacing your hot zone components or checking for discoloration based on how much time
has gone by, the PdMetrics algorithms running in the background analyze a variety of data
www.themonty.com
J.L. Becker Company News. "J.L. Becker, a Gasbarre Furnace Group company, is pleased
to announce the appointment of Jeff Schlais as Sales Representative for the State of Illinois.
Over the past 20 years, while working in the heat treat and automation
industries, Jeff has developed a unique blend of technical, managerial and
sales skills that will prove beneficial to J.L. Becker Company’s growing
customer base. Since the start of his career, Jeff has worked his way from
the ground-up, where he held positions as electrical/robot technician,
controls engineer, sr. controls engineer, electrical project engineer,
electrical/software engineering manager and president. In 2008, Jeff
founded Absolute Machine Controls Technologies Inc. to provide
engineering services, such as electrical and software design for industrial
machine controls and furnaces. Then, in 2014, Jeff founded Absolute
Furnace Controls, Inc. to provide process control systems and retrofit
upgrades for industrial furnace controls used specifically in the heat treat
industry. In fact, Absolute Furnace Controls, Inc. currently assists J.L.
Becker Co. with furnace controls and electrical design, so Jeff and his team
of engineers have a working knowledge of the J.L. Becker heat treat
product lines. Jeff holds a Bachelor of Science in Computer Science from
American Sentinel University in Birmingham, AL. He also holds an
Associates of Applied Science in Electromechanical Technologies from
Northcentral Technical College in Wausau, WI. J.L. Becker Co. is excited to
welcome another well-established individual into its sales force and plans
to continue this growth with experienced and knowledgeable personnel.
Located in Plymouth, MI, J. L. Becker has manufactured industrial heat
treating equipment for over 40 years, providing excellence in design, construction and
service. The company custom designs and manufactures heat-treating equipment for the
specific needs of our customers." February 4, 2016.
points to let you know at the earliest possible time that a negative deviation has started.
However, PdMetrics doesn’t stop there. It also:
•
•
•
•
•
Of course, PdMetrics is more than just what it’s able to do. What you’re getting by
integrating predictive maintenance with your heat treatment equipment is a smart,
connected furnace that monitors your equipment in real time and captures data that helps
you refine your furnace operations. It also provides you with the ability to:
• Anticipate future furnace problems
• Reduce unplanned downtime
• Achieve better furnace performance through proactive maintenance
• Leverage Ipsen’s vast experience through automated analysis
performed by the PdMetrics algorithms
• Experience real-time furnace visibility for faster, better decision
making – from viewing dashboards at the furnace, office PC, smartphone or
tablet to sending urgent alerts by text or email
• Achieve smart factory integration with furnace fleet analytics,
allowing you to see the health of all furnaces at all of your facilities
• Analyze data surrounding failures to determine the root cause
We also analyze the data in our secure Diagnostic Support Center where
we look for anomalies and trends that may indicate the need for further
actions. We then contact you directly with suggested next steps when
needed. If a customer selects the Platinum Protection Plan, we will also
immediately send a qualified technician and any needed parts to help
resolve
the
issue.
In the end, our goal is to provide innovative solutions that help our
customers optimize their operations. PdMetrics not only provides predictive
maintenance, but it is also a tool that helps our customers to efficiently,
and cost-effectively, reduce unnecessary downtime. A tool that helps them gain more control
and harness the power of possibilities. PdMetrics is now released for use in North America on
all horizontal furnaces with up to a 48 x 48 inch cross section, or bottom-loading furnaces
with up to a 60-inch diameter. Global roll out will take place by mid-year. For more insights
into Ipsen and our newest products and technology, visit www.IpsenUSA.com. February 4,
2016.
www.themonty.com
•
Analyzes pumping performance, trending vacuum levels and compares them to
ambient humidity conditions and leak-up rate
Tracks the cooling motor vibration to provide early warning of motor bearing failure
Monitors and compares several hot zone data points, looking for trends that may
produce failures or reduced uniformity
Checks for trend changes of numerous real-time data points that are early indicators
of component or furnace problems
Pushes algorithm improvements automatically to the entire PdMetrics installed base
Checks argon or nitrogen quench gas purity before every backfill or partial pressure
cycle (this is an optional feature)
www.themonty.com
Lights Out Heat Treating. Heat treating is heat treating in all areas of the world. Granted
there are some small differences in the types of products heat treated, in some areas
electrically heated furnaces make more sense than gas and sure furnaces in North America
might tend to be larger than in India but these are all pretty small differences- a Batch IQ
furnace is a Batch IQ furnace no matter where it is located. However visits to regions such as
Europe and Japan reveal a difference which is perhaps subtle at first glance. The Japanese
and the Europeans tend to have a far larger % of completely automated or “lights out”
installations than in other parts of the world (the basic concept is a completely automated
line requiring no operators whatsoever to load/unload or transfer). Where lights out
installations are relatively common in Europe and Japan they are quite uncommon in North
America-as a matter of fact only two come to mind. Why the difference? In Japan we were
told that with the oldest population of any country in the world they just can’t find operators
and automation picks up the slack. Makes sense. That’s not the reason though in Europe and
the most common explanation we have heard has to do with hiring and firing workers.
Namely that companies are reluctant to hire any more workers than they have to because
the costs and difficulties of letting an employee go when production slows down are
enormous. Again makes sense to us. North America with relatively young labor available and
relaxed laws about letting employees go makes the choice fairly simple people are still
cheaper than automation (we will temper these thoughts by saying that it depends upon
which areas of North America we are talking about, the southern US is benefitting in
particular because of low labor costs, weak unions and relaxed laws about laying off
employees). The first two employees below are courtesy of Dowa and show a completely
automated plant. The third photo, compliments of Ipsen show a completely automated batch
IQ installation. February 3, 2016.
ALD Vacuum Technologies Acquires ALD Holcroft. Now this is an interesting
development, but one which probably will not result in any substantial changes. Speaking
from experience I can say that the partnership was a successful one.
Carlos Torres Jr./Mattsa Crio Interview. Carlos Torres of Mattsa/Crio in Mexico
represents what I would consider to be the younger generation who is starting to take over
the heat treating industry. We spoke with Carlos recently and these are his thoughts on the
heat treating industry.
1) Carlos to start off why don’t you tell us who Mattsa Crio is and what the
companies do?
"MATTSA is a Furnace Company , we design, manufacture, service and retrofit Heat treat
Furnaces in Mexico under AFC-Holcroft Licensing. CRIO is a Commercial Heat Treat Company
with serveal locations in Mexico specialized in Hardening, Carburizing, Annealing and
Nitriding processes."
2) Which are you most involved with and which do you prefer?
"I like both companies, they are very different in many ways but I must say that I have been
learning how to run a Commercial Heat Treat and I enjoy it very much, but MATTSA has
been growing in the past years which makes it a great experience to handle all kind of
challenging projects. I can tell you that building and installing furnaces is way more time
demanding than commercial heat treating since every project is unique and always under
tight deliveries. Commercial Heat Treating on the other hand requires more long term
planning and strategy."
3) And how did you get involved with the industry?
"When my father started the company years ago I started to work in the shop doing piping
and service work on furnaces. This exposed me to the building and servicing of furnaces but
not to the overall industry. For some time I continued to work part time on projects. Years
later when I was about to drop school, Steve Thompson from SSI offered me a job in
Cincinnati where I became really exposed to the Heat Treat market outside of just the
manufacturing. My job was doing service calls and installations. One day Steve took me to a
Heat Treat Show in Detroit where I met many Commercial Heat Treaters like Jim Canton
www.themonty.com
AMG Advanced Metallurgical Group is pleased to announce that ALD Vacuum Technologies of
Hanau, Germany, has acquired the remaining 50% share of their joint venture company,
ALD-Holcroft Co. Inc. of Wixom, MI, USA from AFC-Holcroft LLC of Wixom, MI, USA. ALDHolcroft, formed in 2005, acts as the exclusive sales agent for ALD's heat treatment product
lines in the NAFTA region. The acquisition will enable AMG to streamline its heat treatment
and metallurgy furnace marketing operations in North America, Canada and Mexico. About
AMG. With approximately 3,000 employees, AMG operates globally with production facilities
in Germany, the United Kingdom, France, Czech Republic, United States, China, Mexico,
Brazil and Sri Lanka, and has sales and customer service offices in Russia and
Japan. February 3, 2016.
from Flame Metals, Chip Keough from Applied process and John Hubbard of Bodycote (I
even met you during that show Gord). I had the opportunity to talk to them and and they
were all very encouraging when I told them that my father was building a Commercial Heat
Treat company from scratch. Then I decided to go back to school and subsequently started
to work full time for MATTSA and CRIO." Continue Reading February 2, 2016.
Key Features
•
•
•
•
•
•
•
Centralized location to define and manage all Customer Part and Vendor Product Risk
Analyses
Use RA Templates to build and manage unlimited risk and responses
Security Roles control who has the authority for Level 1 and Level 2 signoff, as well as
filling out a RA
Stop Quotes from being printed or emailed if there are missing Part RA’s
Generate Work Order Notes and Notifications if a risky part has been added
Decide a Date as to when Customer Parts and Quotes should be tested. If before the
specified dates, the RA will not be required.
Assign default RA Templates to use for specific Customers and Vendors
BLUESTREAK™ Suite is designed exclusively for a service-based manufacturing environment,
where the primary focus is processing and not inventory management. Find out more at gobluestreak.com ." February 2, 2016.
www.themonty.com
THROUGHPUT I BLUESTREAK™. "A leading provider of Manufacturing Execution System
(MES) software, is pleased to announce Bluestreak I Risk Analysis™, (RA), is available as an
add-on license to Bluestreak I Advanced Quality™, designed for the demanding quality
requirements of Nadcap, AS, TS and ISO accredited companies." “The ultimate goal of risk
analysis is risk mitigation. With risk, there is potential gain as well as the possibility of a loss.
When managing risks, a company must be aware of both the gains and losses incurred in
their day-to-day business operations. Bluestreak | Risk Analysis™ is a key component of the
overall risk management process, with the goal of mitigating the negative impact of external
and internal disturbances in order to avoid interruptions in production, product quality issues
and financial losses,” states Todd Wenzel, CEO of Throughput IBluestreak™.
One of the largest captive heat treaters in the US is Caterpillar, Inc.,
with a number of manufacturing locations including a very large location
in East Peoria, Illinois. With sales down the company is laying off 670
employees and closing five plants including Building HH in East Peoria.
This certainly got our attention as Caterpillar does a great deal of heat
treating in Building HH. No word yet on how this will effect Caterpillar’s
overall heat treating. Last week we told you how Conrad Knerr of
commercial heat treater Metlab had passed away. Here are some further
details. "Conrad Hering Knerr, 91, of Blue Bell, an engineer, business
executive, and entrepreneur, died Thursday, Jan. 21, at his home in
Whitpain Farm of complications from a fall in September. Mr. Knerr served
in the Navy before emerging into the workforce to run Metlab Co., a firm
founded in 1928 by his father, an expert in metallurgy. Over the years, he taught classes in
metallurgy at Temple University and Spring Garden College. He served as a consultant to
heat-treatment firms and was president of the Metal Treating Institute, an industry
advocacy group. A celebration of life will be at 2 p.m. Friday, Jan. 29, at St. Thomas' Church,
Whitemarsh, Bethlehem Pike at Camp Hill Rd., Fort Washington. Interment is private".
We told you a little while back how furnace builder and commercial heat treater Dowa based
in Japan was building a new commercial heat treat in Queretaro, Mexico. Work is
www.themonty.com
Monday Morning Briefing. We will start off in Ohio where it appears “alloy” company
Qual-Fab has made an acquisition. “Qual-Fab, Inc. of Avon, Ohio announces the recent
acquisition of all of the drawings and records of LEE WILSON ENGINEERING COMPANY
and LEE WILSON INC. Lee Wilson Engineering Company, Cleveland, Ohio, formerly a
major player in the bell annealing market supplying thousands of furnaces for the Steel and
Wire Industries over the past 75 years dating back to the 1930s. Many of the major
innovations involving radiant tube furnaces and high convection annealing have roots going
back to the Lee Wilson Engineering Company. Most drawings, records, and designs are now
the property of Qual-Fab, a major supplier of stainless and alloy fabrications to the metals
industry. Qual-Fab has a strong emphasis on bell annealing equipment and can fabricate
equipment to exact Lee Wilson designs and specifications, as required by the customer. As a
major supplier currently to many OEM furnace builders, Qual-Fab supplies radiant tubes,
high temperature fans, and a wide variety of stainless and high alloy fabrications to their
custom designs. If we can be of service, please do not hesitate to call Qual-Fab, or contact
us at www.qual-fab.net. From Retech Systems we have this story; "Eric Petereit was
promoted to the position of Managing Director of Retech Systems LL, effective January 15,
2016. It is with great pleasure that Retech Systems LLC and SECO/WARWICK formally
announce the promotion of Eric Petereit to the position of Managing Director of Retech. Eric’s
time at Retech began in September of 2007 as a Program Manager. Most
recently he held the position of Director of Operations, where he was
responsible for engineering and design, program management,
purchasing, fabrication and assembly, as well as shipping. Concurrently,
Jim Goltz, Retech’s former owner, will be stepping down after 12 years
as the President of Retech Systems LLC. Jim will continue to support the
organization as Senior Advisor at Retech and will likewise continue his
involvement as a member of SECO/WARWICK Group’s Supervisory
Board.
Hightemp is the largest commercial heat treater in India with 5 Heat
treat plants across India processing 9000 tons per month. Well the
company will soon be getting larger with two new plants scheduled to be
in operation by the end of 2017. The plant in Bidadi (Karnataka) is being
set up primarily for a large German manufacturing company and the
second in Ahmedabad (Gujarat) will be the largest in the state. The total investment for
the two new plants is approx. $18 million USD. Please, please just make it stop! I swear
every single heat treater around the world must be receiving daily e-mails from Sean Chen
with the organizing committee of CIHTE2016 who has a heat treat show coming up in
Shanghai this year. On any given day we must receive 2 or 3 e-mails from Sean, generally
from different e-mail addresses. Well Sean I am not going to your silly show just because of
all the e-mails. February 1, 2016.
Notice: We have attempted to describe all equipment accurately from the information we have
available. Any mistakes are unintentional. We do not guarantee the accuracy of the information, nor
can we guarantee the performance of the equipment or suitability to your application. The equipment is
sold as-is, where-is. We strongly encourage your personal inspection of the equipment before
purchase.
www.themonty.com
progressing and the plant is planned to open April 2016. Dowa is building the facility to
support the local Toyota plant. Commercial heat treater Accurate Steel Treating out in
Southgate, CA is adding some more capacity in the form of a vacuum oil
quench furnace. Accurate is one of the larger commercials on the US west
coast. Coatings is an industry long associated to some extent with heat
treating which is why we mention a new company in Virginia who recently
installed two large capacity chemical vapor deposition (CVD) coating
reactors. "Hardide Coatings, headquartered in Bicester, Oxfordshire,
UK, has announced the opening of a new $7million production facility in
Virginia, USA. The expansion has been driven by increased demand from
North American customers, with sales to the US and Canada more than
doubling during 2015. The new factory is expected to create up to 29 jobs
over the next three years. The site in Martinsville-Henry County will
service existing and new customers for the company’s patented range of
hard wearing tungsten carbide coatings in the oil and gas and flow control
markets. In addition, the company also plans to expand in the aerospace
and advanced engineering sectors and develop applications for its newlypatented coating for diamonds".
Used Equipment
Listing Used Equipment
Want to get true market value for your used heat treating equipment?
themonty.com is the only way to do this! Unlike used equipment dealers we work
on a commission basis meaning no high overheads, no buy and resells, no high
expenses which means that you as a seller get what your equipment is worth-not
what a used equipment dealer will pay you for it. Not sure what your equipment is
worth or how saleable it is? Let us know and we can give you a free appraisal and an
honest answer about market conditions-no BS. Before listing we will require a signed
copy of the "Terms and Conditions". Please use our Contact Form or email Dale
at dale@themonty.com all pertinent information including asking price (which we
strongly recommend) age, condition and if possible photos. When selling please
keep in mind that we do NOT ask for an exclusive sales agreement - if we don't sell
it we don't get paid - PERIOD. You can’t lose by listing with themonty.com we sell
your equipment or we don’t get paid-period.
Notice: We have attempted to describe all equipment accurately from the
information we have available. Any mistakes are unintentional. We do not guarantee
the accuracy of the information, nor can we guarantee the performance of the
equipment or suitability to your application. The equipment is sold as-is, where-is.
We strongly encourage your personal inspection of the equipment before purchase.
www.themonty.com
At "themonty.com" you are guaranteed of finding the best priced used equipment
in the industry due to the fact that we do not buy and resell and have no associated
costs. Instead we put buyers and sellers together on a small commission basis
meaning that at the end of the day you are paying what equipment is worth-not
equipment with a huge mark up attached! In addition you generally can see the
equipment installed, running and talk to the actual operator far better than seeing a
used furnace in the back of a dingy warehouse. Don’t see what you are looking for?
Let us know and we will find it for you. Please feel free to Contact Us.
European
See something you need, scroll through all the items for sale. Searching for something we
don’t have listed, fill out our Contact Form.
•
•
•
•
•
Borel Fluidized Bed Furnace
CODERE Multi-Purpose
Furnace Line
Ipsen TQ-5-EM Furnaces (2
available)
JLS Redditch GAS HEATED
OVEN
Gebruder Hammer
Endothermic Generator
SOLO Continous Furnace
SOLO Furnace Line
•
•
•
•
•
•
SOLO Furnace System
SOLO Second Hand Continous
Furnace
SOLO Second Hand Quenching
Machine
Somet Vacuum Furnace
Somet Vertical Vacuum
Furnace
TAV 6 Bar Vacuum Furnace
Item E025 CODERE Switzerland System 250 42/100. This installation was
manufactured in 2005 and is situated in Switzerland. Due to the reduction of inhouse heat treatment, customer decided to sell this line and use commercial heat
treaters. Austenitizing, carburising and carbonitriding furnace with operating
temperature of 1050°C. The main voltage is 3 x 400V - 50Hz. The maximum weight
per load is 250 kg with loading dimensions consisting of 420 mm x 1000 mm.
System consists of a Salt quench tank – 2x Austenitizing furnace – Tempering
furnace under protective atmosphere (N2) – Washing machine x 2 (Pre & post wash)
with salt recuperator – Semi automatic manipulator with gas cabinet - Loading/
Unloading table (Suitable for 3 loads). Carbomanagement software recording all
history and cycle parameters with the necessary controllers. 1 N2 gas cooling unit
(0.2 bar). Possiblity of adding additonal quenching mediums to the line (Water &/ or
oil) Codere confirm this installation will be dispatched back to supplier in order to
undertake retrofit of retorts before dispatch and overall insepction of line. Well
maintained and has been shut down since June 2015. Visit possible until beginning
of Febraury 2016.
www.themonty.com
•
•
Item #E023 JLS REDDITCH GAS HEATED OVEN. Year of manufacture, 200.
S/N:00/4665. Completely refurbished. Internal size: 900w x 500d x 450h. Operating
750C. Asking £9,500 ex works.
Item # E022 Solo Furnace System. Model SOLO 202-30/30/30. System consists
of a Water quench tank – Austenitizing furnace – Salt quench tank – Tempering
furnace – Washing machine with salt recuperator – Forklift – Switch and control
panel and gas distribution cabinet – Computer management system for process
control. Line is capable of Austenitizing – Carburizing – Carbonitriding – Tempering
– Water/Salt quenching – Washing. Excellent condition. Asking 65 000 € HT
Year of manufacture : 1990
Max. temperature : 1100°C
Main voltage : 3 x 400 V - 50 Hz
Max. weight of a load (gross weight) : 50 kg
Effective loading dimensions : 300 x 300 mm
Max. loading height : 300 mm
www.themonty.com
Item E024 TAV 6 BAR VACUUM FURNACE. . Model TP600 built in 1999. Working
dimensions of 600mm W X 600mm H X 900mm D. Footprint of 4.5 m W X 3.5 H X
6.5 D. Maximum operating temperature of 1300C. Temperature uniformity of +-5C.
Maximum gross weight 600kg. 150kw. Operating vacuum of 10-2mbar. Kinney
mechanical pump Model KT150C. Booster pump Hick Hargreaves. Nitrogen
quenching up to 6 bar. SSI/VAS control system. Graphite insulation and heating
elements. Gross weight 15 tons. Excellent condition. Asking £150,000 ex works
UK
Year of manufacture : 1992
Max. temperature : 1000°C
Main voltage : 3 x 400 V - 50 Hz
Max. weight of a load (gross weight) : 80 kg
Effective loading dimensions : 300 x 300 mm
Max. loading height : 600 mm
Item # E019 Somet Vertical Vacuum Furnace. Weight capacity 250 Kgs.
Working dimensions of 700 mm X 900mm high. Power Input 415 V, 3 Phase 50 Hz
with Brendford regulating auto transformer Serial No. 89.0331 type RDOAQ 240/415
KVA52 Brendford regulating transformer. Serial No.89.0331 Type RDOQIM 110/4
KVA 104.5. With EUROTHERM 2404 Programmable Controller, with 6180XIO Data
controller and 2500 series input/ output module, Edwards 1150 vacuum control with
Pirani and Penning passive gauges, Eurotherm 2208e excess temperature control
with over temp. alarm. Individual digital display phase voltmeters and ammeters,
water flow alarm indicators. Maximum temperature 1250 deg C, Operating
temperature 1200 deg C. Vacuum ultimate 10-5 mb range, typical operating
vacuum 10-4 mb range. Complete plant with Edwards Diffusion pump model No.
ED400, Stokes MICROVAC vacuum pump model 412H-10. Hot zone Graphite
elements, graphite insulation lined 40mm fibreboard foil faced. Load weight approx.
250 Kgs - with pumps, water cooling manifolds and pipework for water cooling (to
be connected to cooling system - not included). Pillar jib crane available at separate
negotiation 500Kgs. Asking price £130,000 net - Disassembly, transport,
assembly and start-up at buyer’s site not included, but could be offered separately.
Excellent condition. Refurbished and can be shown working.
www.themonty.com
Item # E021 Solo “Bell Type” Furnace Line. Built by Solo of Switzerland this is a
Model SOLO 202-30/30/60. Line consists of an oil quenching tank – Austenitizing
furnace – Nitriding furnace – Washing machine – Forklift – Switch and control panel
and gas distribution cabinet – Computer management system for process control :
Easytherm CarboBELL Pro. This can be used for Austenitizing – Carburizing –
Carbonitriding – Nitriding – Oil quenching – Washing. Very good condition. All
manuals included. Asking 75 000 € HT
Item #E016 Borel Fluidized Bed Furnace. Model LF-1. An ascending gas
stream, which can be neutral or reactive, makes fluid a sand bed. The gas is
introduced regularly in the sand bed through a porous metal special plate. Can be
used for Heating before hardening - Annealing - Carburizing. Cover in 2 parts Control panel - Gas distribution panel. Very good condition, entirely revised,
delivered with the manufacturer's instruction manual. Manufactured in 1981.
Maximum operating temperature 1900F. Power input 15Kw. Inside diameter
250mm, depth 400mm, weight capacity 700kg. Asking €6’500 Euros
Item # E015 SOLO Swiss Continous Furnace. Model 322-10-80C. Entry frame
with loading area - Heating part with frame - Cooling part with frame and exit
chimney - Exit frame with unloading area - Belt drive and conveyor belt Distribution for treatment and cabinet gas - NH3 cracker 3m3/h - Electric control
cabinet. Used for Annealing under cracked ammonia - Brazing – Hardening.
Manufactured in 1990. Maximum operating temperature 1800F-2,000F. Main voltage
www.themonty.com
Item # E018 SOMET VACUUM FURNACE. Weight capacity of 250Kgs, working
dimensions of 700 X 700mm. Maximum operating temperature of 1250C. Horizontal
loading. Power Input 415 V, 3 Phase 50 Hz with Brendford Transformer, onload
regulating transformer unit type RDOQM 90/04 oil cooled. With EUROTHERM
Programmable Controller, with pumps and some pipework for water cooling.
Maximum temperature 1300 deg C, Operating temperature 1250 deg C. Vacuum
ultimate 10-6 mb range, typical operating vacuum 10-5 mb range. Complete plant
with Varian Diffusion pump K4816-326 VHS-400, Stokes MICROVAC vacuum pump
model 412H-16. Hot zone: Graphite foil elements, graphite insulation lined 40mm
foil faced. Load weight approx. 250 Kgs. Asking price GBP 130,000 Disassembly,
transport, assembly and start-up at buyer’s site not included, but could be offered
separately. Excellent condition.
3 X 380V-50Hz. Maximum weight of a load (gross weight) 80 kg. Effective loading
dimensions 300 X 300 mm. Maximum loading height 600mm. Good condition,
entirely revised, delivered with the manufacturer's instruction manual. Mounting,
commissioning and training worldwide upon request. Asking €24’000 Euros.
Item # E012 SOLO Swiss Furnace. Model 321-7-90. Loading frame - Heating
part with frame - Cooling part with frame - Unloading frame - Driving system Conveyor belt - NH3 cracker 3m3/h - Distribution for treatment and cabinet gas Operator panel. Annealing under cracked ammonia - Brazing – Hardening.
Manufactured in 1990. Maximum operating temperature 1800F. Main voltage 3 X
380V-50Hz. Power input 10.5 Kw. Gas generated; 75% H2 and 25% N2 (NH3),
Heated length 900mm, cooled length 1500mm, channel section 80 X 40mm.
Effective height with belt 30mm. Conveyor belt width 70mm. External dimensions
Length 5300mm X 1800mm X 1250mm height. Perfect condition, entirely revised,
delivered with manufacturer’s instruction manual. Mounting, commissioning and
training worldwide upon request. Asking €26’000 Euros
Item # E011 SOLO Swiss Quenching Machine. Model 209-30/30. Quenching
machine for self-hardening and oil quenching. System consists of a Quenching Bell
furnace - Nitrogen quenching unit - Tempering furnace - Oil quenching unit Controller / programmer - Operator panel - Temperature controller - Hydraulic
www.themonty.com
Item # E013 GEBRUDER HAMMER Endothermic Generator. GEBRUDER
HAMMER Endogas Generation Plant. Model Endogen 120-1.05-G, with dew point
controller. Size;120 m3/hour (3600 CFH) or manually adjusted to 60 m3(1800 CFH)
Shipping weight 4.000 kg. Dimensions ; LxWxH. 3600x2400x2800 mm. Year Built;
2001 Condition; Operational, very good. Asking Price : 43.000 euro (58.500
usd).
Item #E004 Ipsen TQ-5-EM Furnaces (2 available). Located in the UK. Two
Ipsen TQ-5-EM straight through batch IQ furnaces, with loading system, tempering
furnace and washing machine. Load size 610mm (w) x 610mm (h) x 910mm (d),
rated at 350kg's each and operating temperature up to 1050C. Uniformity +-10C.
Electrically heated 172A. 380 volts, 3 phase, 50hz. Set up for Endo Atmosphere.
Ipsen "Carbo Prof" control system. Control panels missing and heating elements
missing. Brickwork in good condition. Asking £55,000. New in 1987. Total
refurbishment can be offered, new control panel, gas or electric heating etc.
www.themonty.com
control. Can be used for Austenitizing - Annealing - Tempering - Oil quenching Quenching under nitrogen. Manufactured in 1991. Maximum operating temperature
of 2100F. Main voltage 3 X 400V-50Hz. Power input; 10kW. Working dimensions of
300mm diameter X 300mm high. Maximum loading weight 20kg. Protective gas; N2
or mixture N2 to max. 5 % H2. Overall dimensions of 2200mm high X 2070 wide X
2250mm deep. Good condition, entirely revised, delivered with the manufacturer's
instruction manual. Mounting, commissioning and training worldwide upon request.
Asking price: €35’000 Euros
Batch
See something you need, click on the link or scroll through all the items for sale.
Searching for something we don’t have listed, fill out our Contact Form.
•
•
•
•
•
•
•
•
•
•
Atmosphere Box Furnace
Atmosphere Box Furnace
Batch IQ Line
Beavermatic Batch IQ
Furnace
Dow Batch IQ Furnace
Dow Batch IQ Furnace
Electric Box Furnace
Fluidized Bed Furnace
High Temperature Tube
Atmosphere Furnace
Hydrogen Atmosphere Box
Furnace
Hydrogen Atmosphere
Furnace
Ipsen T-11 Batch IQ Furnace
Ipsen Batch IQ Installation
Lindberg Batch IQ Furnace
•
•
•
•
•
•
•
•
•
•
Lindberg Electric Pit Type
Cyclone Furnace
McLaughlin Services Test
Furnace
Pacific Scientific Box Furnace
Plasma Nitriding System
Sauder “Auto-Tilt” Car
Bottom Furnace
Selas Batch IQ Furnace
Sunbeam AF-10 Batch IQ
Furnaces (3 available)
SURFACE COMBUSTION
BATCH IQ FURNACE LINE
Surface Combustion Batch
IQ Furnace
Super 30 Allcase Line
Item # B395 Ipsen Batch IQ Installation. This 5 year old installation consists of
2 Ipsen carburizing furnaces with working dimensions of 36" X 48" X 36", both gas
fired. Four (4) gas fired Ipsen tempers 36" X 48" X 36" capable of 1400F, an Ipsen
dunk/spray washer and 2 charge cars. Carburizing furnaces are a "flow through
design" using endothermic atmosphere. Atmosphere control is through an oxygen
probe/Siemens 3 gas IR system. The entire installation is designed for "lights out
operation" meaning it is completely automated. Included is over $100,000 worth of
spare parts along with 15 base trays and baskets. The equipment is currently
installed but not in use and is in immaculate condition. New the system was $3.5
million USD, asking price is $1.4 million USD.
www.themonty.com
•
•
•
•
A Lindberg 1000 CFH Gas Fired Endothermic Generator is included with the system
along with multiple spare parts including radiant tubes, roller rails, chain guide and
fan assembly. In addition to the spare parts all the alloy baskets and grids are
included. The equipment can be shown in operation by appointment until the end of
the year. The asking price of $45,000.00 includes the removal and loading of the
equipment on to the buyers transportation. The equipment is being offered “As
Shown”.
Item # B393 McLaughlin Services Test Furnace. Working dimensions of 19”W x
20”H x 18”D. Can run electrically or with natural gas. Capable of 3000 F. Natural
Gas: 75 CFH @ 5 psi. Nitrogen: 60 CFH @ 5 psi. Electrical: 480/3/60, 60 Amp.
Purge Volume: 25 cubic feet. This is a state of the art furnace which can be run
remotely. Anything iron related needs this type of furnace for testing. This furnace
should be considered brand new as it was used only once for testing. New $150,000
USD, Asking $45,000 USD.
www.themonty.com
Item # B394 Dow Batch IQ Line. Internal Quench With Top Cool, Model DW243622-GRQ S/N HG-20-21. Working dimensions of 24”W x 36”L x 22”H. Gas Fired
Radiant Tube – 800,000 Btu/hr. 1750°F Max. Temp. Voltage 460/3/60. Footprint
9’W x 14’L x 12’H. Controls: SSI Model 9200 Programmable Dual-loop Controller,
SSI VR12 Digital Chart Recorder, Honeywell UDC-2500 over temperature controller.
A Nema12 double door panel houses all furnace control hardware. Carbon control is
provided by the SSI 9200. The furnace heating chamber is fiber lined, with four
vertical U-Tubes, two on each sidewall heated by Eclipse Therm-Thief recuperative
burners. A rear handling system is used to transfer the workload. The quench tank
has variable speed agitation and an oil cooled top cool chamber. Quench tank
capacity is 1200 gallons and utilizes an SBS air to oil cooling system. The
atmosphere system consists of Waukee Tronic flowmeters for endothermic, nitrogen,
air and natural gases. Carbon is controlled by an SSI Gold Probe.
Item # B390 Dow Batch IQ Furnace. Gas fired with working dimensions of 30” X
48” X 30”. Excellent condition with new Eclipse burners, side cool option, new
brickwork and new SSI atmosphere and temperature controls-touch screen. Also
comes with spare alloy including base trays, cast baskets and radiant tubes.
Available immediately.
Item # B388 Hydrogen Atmosphere Furnace. Manufacturer:
CM
Furnaces.Type: Hydrogen Atmosphere Box. Work Zone Size: 12" x 12" x 12". Max.
Temperature: 2000ºF. Uniformity: Full work zone, prob. +/- 50ºF. Lower 6": prob.
+/- 20ºF. Atmosphere: Wet or Dry Hydrogen or Nitrogen Purge. Controls: PLC Automatic with Proface touch screen. Price: $5,000 USD.
www.themonty.com
Item # B391 Ipsen T-11 Batch IQ Furnace. Model T-11 gas fired batch IQ
furnace with an operating temperature of 2000F. Working dimensions of 36"W x
24"H x 48". Voltage 460/3/60. External dimensions of 9’W x 14’7”H (Assembled) x
22’L – Approx. Standard T-11 Ipsen batch type atmosphere furnace with integral hot
oil quench. Furnace has "Waukee" flow meters for Ammonia, Endo, Air and Natural
Gas. There are a total of twelve (12) Eclipse (SER) single ended recuperative
burners with Kanthal APM (Advanced Powdered Metallurgical) vertical radiant tubes.
Controls mounted and wired in an enclosure attached to the right hand side of the
furnace includes the following a Yokogawa digital temperature control, Yokogawa
digital over temp control, Yokogawa digital oil temp control, Yokogawa digital over
temp (oil) control, three (3) A.C. Amp meters, one for each quench agitator and all
necessary pushbuttons, signal lights, etc. Quench tank is gas fired with an Eclipse
burner package. This furnace includes a stationary loader, gas fired Dunk & Spray
washer, manuals & drawings. Good condition, just moved to indoor heated storage.
Asking $75,000 USD.
Item # B387 Hydrogen Atmosphere Box Furnace. Manufacturer: Pathways
Thermal Technology. Type: Inconel Retort Atmosphere Box Furnace. Work Zone
Size: 12"W x 16"D x 12"H. Atmosphere: Any, but set up now for Argon. Max.
Temperature: 2100ºF. Heating: Electric, Globar elements. Cooling: External
retort forced gas cooling system. Price: $10,000 USD.
Item # B385 Lindberg electric pit type cyclone furnace / nitriding furnace
type: 12-ec-1620-12, 480 volts, 27 kw, 3 phase, 1-1/2 h.p. fan motor,max
opperating temp: 1250 f, working dimention: 16” dia. X 20” deep, aprox. Weight:
1700 lbs., heating elements: helical coil type nichrome v, this furnace is equipt with
a sealed retort and fan assembly for gas nitriding. $9,800.00 USD.
Item # B384 Plasma Nitriding System. Made by Plateg of Germany this is a
pulse Plasma Nitriding unit with working dimensions of 39.37” diameter (1000mm)
and 47.24” high (1200mm). Maximum workload of 4409 pounds (2000kg).
Maximum operating temperature of 1112F (600 C). Photos below show the system
as installed, recently it was dismantled and is in heater storage. Complete and in
good condition although it does require a high frequency control module for the
pulse plasma supply. Asking $49,000 USD.
www.themonty.com
Item
#
B386
High
Temperature
Tube
Atmosphere
Furnace.
Manufacturer: Blue-M.
Type: Atmosphere
Vertical
Tube
Furnace.
Max.
Temperature: 2500ºF. Work Zone Size: 2" Diameter x 12"High. Heating: Electric,
Globar elements. Tube: Ceramic. Atmosphere: Air or Any Suitable Purge Gas. Last
Use: Thermocouple Calibration. Price: $2,500 USD.
1.)For thermal diffusion of Vanadium
2.)For DST process (license required)
3.)Austenizing
4.)Tempering
carbides on to high carbon
of Chromium nitrides on to
steel.
steel.
System consists of high heat furnace sand quench, transfer hood, HCL safety
cabinet and controls and scrubber. Used Argon, Nitrogen and HCL gases. Comes
with Full touch screen controls with remote access via ethernet and wifi. The photos
below show the Scrubber and safety cabinet, Quench, Furnace hot zone and 3x
control/gas/electrical cabinet in the background and the transfer hood. Excellent
condition, currently installed and used for only 50 cycles. New over $300,000 USD,
asking $95,000 USD.
Item # B378 Batch IQ Line. This is a complete line consisting of the batch IQ,
Model FC-364830, washer Model FCW-364830, temper Model FCT-384830, charge
car, load table and control cabinet. Manufactured by CEC in 2007. Working
dimensions of the batch IQ, temper and washer is 36” wide X 48” deep X 32” high.
Batch IQ is electrically heated and uses Moly-D (molybdenum disilicide) heating
elements. High heat is set up for endothermic atmosphere. All the equipment is in
excellent condition and virtually unused. Located in the US northwest. New this was
over $1 million USD. Asking $275,000 USD.
www.themonty.com
Item # B382 Fluidized Bed Furnace. Manufactured by Applied Heat Technologies
in Australia and designed by HARD Technologies. Working dimensions of 12”
diameter x 36” work. 1860F maximum temperature. Built in 2012. This system is
capable of multiple uses including;
Item # B373 Lindberg Car Bottom Kiln. Lindberg Hevi-Duty Kiln/Division of Sola
Basic, Model 277236-ECB-26A, Serial No. 20049. This Kiln is electric with a max
temp of 2600° F. Car approximate dimensions 8′ long x 4′ wide x 4′ high. Asking
Price $35,000(US) or Best Offer
Item # B371 Sauder “Auto-Tilt” Car Bottom Furnace. Working dimensions;
ID: 8’ wide x 30’ long x 5’ high, electric, 480/3/60, 325kw; 1400F, complete with
ceramic fiber lining, 3 zones of control each with top mounted alloy recirculating fan,
powered car with cast deck and 60,000# load capacity, hydraulic pump set for lifting
cylinders, control panel with digital controls. Super clean and in operation. Asking
$179,000.00 USD including disconnecting and loading onto trucks.
www.themonty.com
Item # B374 ATMOSPHERE BOX FURNACE. Manufacturer: R&G Services, Inc.
Inside Dimensions: 18" high x 32" wide x 36" deep. Heated: Electric, 230/3/60, 60
KW. Temperature: 2100 deg. F Model Number: EB-183236 Serial Number: 77021
Temperature Controls: Updated indicating controller and overtemp. Description &
Features: Air operated vertical rising door. Slanted face plate. Brick lined with silicon
carbide hearth. Heated by heavy Nichrome ribbon heating elements. Atmosphere
inlet and burn-off. Flame curtain with controls and safeties. Condition: Very good.
Furnace will be cleaned & painted, repaired as necessary, checked out & test fired
prior to shipment. SALE PRICE: $18,000.00 USD.
Item #B358 Surface Combustion Batch IQ Furnace. (2 available). S/N 121561. Working dimensions of 62” wide X 62” long X 36” high. Quench tank 18’ wide X
10’ long X 7’ deep. Capacity 9500 US gallons. Power 480 Volt, 3 phase, 60 cycle.
Gas fired-4.6 million BTU/Hour. Maximum operating temperature 1850F. Two top
mounted alloy re-circulating fans. 2 Nitrogen flow meters, 2 for natural gas, 2 for
air, 2 for propane and 1 for endothermic atmosphere. All have Waukee-Tronic
process controls. Allen Bradley Panelview PLC-5. Yokogawa Controls. Four 30 hp
gold standard agitators (28” props), 4 U Style radiant tube burners (bottom), 2
Trident tube burners (top), 2 zones with temperature controls, 2 zones with carbon
control, 2 rear handlers, 1 common drive, Eclipse recuperated burners, atmosphere
sample system. Complete and in good condition. Asking $250,000 USD Each.
www.themonty.com
Item #B367 Atmosphere Box Furnace. Manufactured by McLaughlin Services.
S/N MS-11-604-01. Natural gas heated-2.8 MBTU’s/hour. Maximum operating
temperature of 2000F. Voltage 480/3/60/100 Amps. Work area 166"W x 20"H top of
piers to door arch, 32"H opening x 120"L. External dimensions; 16'W x 13'H x 14'L Approx. Controls; Mounted and wired in a free standing panel includes an "Super
Systems, Inc." (SSi) control system with HMI touchscreen interface. Front loading
box furnace with an air operated vertical lift door. Furnace lining consists of ceramic
fiber modules on the walls, roof and door. The floor is insulated with "IFB" Industrial
Fire Brick. The furnace hearth consists of HT alloy rails and is designed to handle
4000 pounds @ 2000°F. There are two (2) roof mounted fans in this furnace to
circulate heat and atmosphere. This furnace is equipped with two (2) Waukee FloTronic Nitrogen Flowmeters. There are a total of ten (10) Kromschröder pulse firing
recuperative burners that fire into "P" type radiant tubes. There are four (4) zones
of control in this furnace. Excellent condition-like new. Asking $165,000 USD.
Item #B352 Pacific Scientific Box Furnace. Working dimensions of 72" wide X
120" long X 48" high, Gas fired radiant tube, maximum operating temperature of
2050F. Air operated vertical lift door, fiber lines, new refractory piers (12), hi-temp
horizontal radiant tubes (6 above, 6 below), full safeties, side exhaust guard. Free
standing control panel-prewired panel with Honeywell Tru-Trend circular chart and
Honeywell digital controllers and overtemp. Atmosphere capable. Comes with spare
radiant tubes. Very good condition. Asking $70,000 USD.
Item #B349 Beavermatic Batch IQ Furnace. 1995 Beavermatic Atmosphere
Integral Quench Furnace with 45" Tall Parts Capability. Model: 64-45E1
S/N:
695-89/1. Condition: Overall - Fair to Good (Brick good, Inner hearth recent
www.themonty.com
Item #B357 SURFACE COMBUSTION BATCH IQ FURNACE LINE.Serial
Number: 12155-1. Working Dimensions: 87” WIDE X 87” LONG X 36” HIGH. Quench
Tank Dims.: 20’ WIDE X 12’ LONG X 7’ DEEP. Quench Tank Volume: 12,500
GALLONS. Power: 480 VOLT, 3 PHASE, 60 CYCLE Fuel: NATURAL GAS - 4,600,000
BTU/HOUR. Maximum Temperature: 1,850°F. Fans: TWO TOP MOUNTED ALLOY RECIRCULATING FANS. Flow Meters: 2 NITROGEN, 2 AIR, 2 NATURAL GAS, 2
PROPANE, 1 ENDOTHERMIC. ALL HAVE WAUKEE-TRONIC PROCESS CONTROLS.
Controls: ALLEN BRADLEY PANELVIEW PLC-5. YOKAGAMA INSTRUMENTS. General:
SIX 30 HP GOLD STANDARD AGITATORS (28” PROPS), 4 “U” STYLE RADIANT TUBE
BURNERS (BOTTOM), 2 TRIDENT TUBE BURNERS (TOP), 2 ZONES WITH
TEMPERATURE CONTROLS, 2 ZONES WITH CARBON CONTROLS, 3 REAR HANDLERS,
1 COMMON DRIVE, ECLIPSE BURNERS & RECUPERATIVE, ATMOSPHERE SAMPLE
SYSTEM. ATMOSPHERE TEMPER: Load Dimensions: 87” WIDE X 87” LONG X 36”
HIGH. Power: 480 VOLT, 3 PHASE, 60 CYCLE. Fuel: 1,500 CFH (1,500,000/HOUR), 4
U TUBES, ECLIPSE BURNERS & RECUPERATORS. Maximum Temperature: 1,350°F.
Controls: ALLEN BRADLEY PANELVIEW PLC-5, YOKAGAMA INSTRUMENTS. General:
ONE COMUSTION BLOWER, ONE (1) COMMON DRIVE, TWO (2) RE-CIRCULATING
FANS. LOADED AND UNLOADED BY CHARGE CAR. PARTS WASHER; HEATED
(FORCED AIR) RINSE/DRY. Load Dimensions: 87” WIDE X 87” LONG X 36” HIGH.
Power: 480 VOLT, 3 PHASE, 60 CYCLE. Fuel: 1,500,000/HOUR. Maximum
Temperature: 180°F. Controls: INCLUDED. General: INCLUDES OIL SKIMMER &
FILTERS. CHARGE CAR IS ALSO INCLUDED. LINE IS COMPLETE AND IN GOOD
CONDITION. ASKING $650,000 USD FOR EVERYTHING.
Item #B342 Electric Box Furnace. Working dimensions of 36” wide X 30” high X
54” deep. Electrically heated; Electric coil heating elements on side walls and under
hearth – 90 KW. 12” Ceramic Fiber insulation. Honeywell Controls – High Limit –
Chart Recorder 2 pin. Max Temp. 1850F. Hearth is being rebuilt. Unit is in very
good condition and is currently under power. Asking $18,500.00 USD.
Item #B336 Lindberg Batch IQ Furnace. Hevi-Duty, Clean Line, Model H66GH,
S/N 102350. Working dimensions of 24” x 36” deep X 24” high. Maximum operating
temperature 1850F. Gas fired 745,000 BTU’s. PLC controlled with oxygen probe.
Air/Oil heat exchanger. Straight through design. Alloy and brickwork in great
condition. Asking $29,900.00.
Item #B331 Selas Batch IQ Furnace. Model 50. Working dimensions of 24" X 36"
X 18" high. 500 pound capacity. Electrically heated. Endo atmosphere. Complete
and in good condition although some elements will need to be replaced. Installed
but not in use. Asking $19,500.00 USD. A dunk washer is also available.
www.themonty.com
rebuild, Radiant Tubes good.) Work Zone: 36"W x 54"L x 45"H. Atmosphere:
Endothermic (generator not included). Carbon Control System (Honeywell UDC
Controller, Probe is SSI Gold Probe. Max. Temperature: 1850˚F Uniformity: +/25˚F from 1300˚F to 1750˚F. OEM Load Rating: 4,000 Pounds Gross Wt. (Discuss
with owner for history of loading). Heating: Electric Elements, 460V/3Ph/60Hz,
runs approx. 100 kW at 70% power setting. Breaker Size: 400 Amp for elements,
150 Amps for controls. Quench Heater and Quench Cooler Included. Air-cooled fan
bearings. Footprint: 13ft W x 19ft L x 15ft H. Pit Required: Currently in pit of 13ft
W x 13ft L x 22in D, but could be only 11-12ft L. Load Cart: Not included with
furnace. Currently in operation and can be demonstrated on your parts. Immediate
Availability. Asking Price: $50,000.00 USD ****New Price****
www.themonty.com
Item #B309 Sunbeam AF-10 Batch IQ Furnaces (2 available). S/N F-06-70-K.
Working dimensions of 24" high X 30" wide X 48" deep. Gas fired, operating
temperature of 1850F. Standard Sunbeam straight through design with automatic
transfer mechanism (pusher type) in front. Heated by ten alloy vertical radiant tubes
with spark ignition. 1000 pound capacity, no pit required. Quench oil agitation and
cooling is achiever by recirculating the oil through a tube and shell type heat
exchanger then through manifolds in the quench tank. Electric immersion heaters.
ACM water detection system. Partlow controls for heating and cooling oil. GM
surplus. Free standing 3 section control panel with updated controls. Barber Colman
model 560 controller and strip chart recorder for temperature and carbon. L & N
overtemp, Barber Colman undertemp control. Barber Colman oxygen probe and
control. 10 sequence timers. Good condition. Asking $35,000.00 USD Each.
Continuous
See something you need, click on the link or scroll through all the items for sale. Searching
for something we don’t have listed, fill out our Contact Form.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Ipsen Pusher Line
Ipsen Pusher Line P-12
Mesh Belt Furnace Line
Mesh Belt Austemper Lines (2
available)
Pacific Scientific Rotary Retort
Furnace
Rotary Hearth Furnace
SECO/WARWICK Roller
Hearth Furnace
Sunbeam Pusher Carburizer
Sunbeam Rotary Hearth
Furnace
Surface Combustion (Pifco)
Roller Hearth Line
Surface Combustion Rotary
Hearth Furnace Line
Wellman Mesh Belt
Brazing/Annealing Furnace
Item # C312 Surface Combustion (Pifco) Roller Hearth Line. 60" x 60" Trays
capable of 4000 lbs per tray. This line is gas fired and includes an SSi datalogging
system. Also includes SBS Heat Exchangers and has waulkeetronic flow meters.
Asking Price: $450,000 USD.
Item # C311 Ipsen Pusher Line P-12. Rebuilt by JL Becker Company. This is a
complete line which includes; a Pre-wash, Hardening Furnace, Oil Quench, Post
Wash, and Temper. It's setup for endothermic atmoshere and is currently installed
www.themonty.com
•
2150˚F Rotary Hearth
Furnace System
AFC-Holcroft Atmosphere
Pusher Furnace System
ABBOTT Model Furnace
Cast Link Belt Quench and
Temper Line
CI Hayes Continuous
Humpback Furnace
C.I. Hayes High Temperature
Tube Furnace
CI Hayes Mesh Belt
Brazing/Sintering Furnace
and operating. Gas Fired, 30" x 30" x 30" Trays. Good overall condition. Asking
Price $250, 000 USD.
Item # C309 Ipsen Pusher Line. Model T-22 GM, S/N 54499, manufactured
1969. High heat furnace consists of a pre-heat, 2 separate zones and an internal oil
quench. Gas fired capable of 1750 F. Endo atmosphere. Straight through vertical
radiant tubes. Used for carburizing. High heat will hold three trays each 36 X 48 with
30" clearance. Each tray can handle at least 2,000 pounds. Also included is a
transfer car, 1250F gas fired temper and dunk/spray washer. Currently installed but
not in use. Alloy and brickwork are in good shape however all controls will need to
be replaced. Overall complete and in in reasonable condition. Asking $49,000
USD.
Item # C308 AFC Mesh Belt Hardening Furnace. Manufactured by Atmosphere
Furnace Company this furnace has working dimensions of 6" high x 54" wide x 12'
long (heated section). Gas fired with radiant tubes. Operating temperature of 1800F.
S/N 6948. Temperature Controls: Free standing enclosed panel. Honeywell solid
state digital readout indicating controllers, L&N overtemps. L&N strip chart
temperature & carbon recorder. Marathon Monitors Carb-Pro carbon control.
Description & Features: Fiber lined. Heated by (9)North American 4724-2-E burners
www.themonty.com
Item # C310 Mesh Belt Furnace Line. Manufactured by San Yun Electric Heat of
Taiwan this gas fired mesh belt line is capable of 2,000 pounds per hour. System
consists of high heat furnace with endothermic atmosphere and pre wash, oil
quench, post wash and 1400F mesh belt temper. Line is complete and installed but
not in use. Comes with over $150,000 worth of spare parts. 4 years old. Like new
condition. New the furnace line was approximately $1.3 million USD. Asking
$600,000 USD.
firing into recuperated U-tubes. Two zones of control. Rear zone has a roof mounted
recirculating fan. Cold belt return. Furnace has a flame curtain and complete
combustion controls and safeties. Includes quench tank and conveyer. Asking
$75,000 USD.
Item # C304 Rotary Hearth Furnace (Atmosphere). Model #DT-53, Serial
number 840-932. Built by IVA in 1990 rebuilt in 2009. Working dimensions; 36”
Wide Rotating Table; Door Opening 20” Wide x 12” High. Electric 480/3/60 – 115
KW. Operating temperature of 1850 Degrees F. Recently Rebuilt Ceramic Fiber
Lined, Atmosphere Capable Rotary Hearth Furnace complete with Vertically Hung
Heating Elements Inside Single-Ended Alloy Radiant Tubes, Brick Hearth, (3) Zones
of Control, Motor Driven Rotating Hearth, (3) Step-Down Transformers, Atmosphere
Flow Panel (for Endo, Natural Gas, and Nitrogen), SSI Carbon Probe, (2) Vertical
Rising Pneumatic Access-Doors, and Atmosphere Burn-Off Flare. Free-Standing
Control Panel complete with Super Systems Series 7 Digital Temperature Controller
(1 Per Zone), Eurotherm High & Low Temperature Limits, Super Systems AC-20
Digital Carbon Controller, and Chessel 6” Strip Chart Recorder. Overall dimensions
of 11’ 10” diameter X 10’ high. Approximate weight 30,000 pounds. Excellent
condition. Asking $91,500.00 USD.
www.themonty.com
Item # C307 Pacific Scientific Rotary Retort Furnace. Electrically heated
Pacific Scientific rotary retort furnace line including loader, weigh scale, high heat
furnace, quench tank, post wash and mesh belt temper. Retort is 13 ½’ long with an
ID of 18”. Retort is 4 years old and has seen little use. Endo atmosphere and rated
for 1700F. Quench tank is currently being used for polymer. Post wash is not
complete. Mesh belt temper 36” wide also made by Pacific Scientific and is rated for
1,000F. 440 volt. Honeywell controls. Furnace is complete and in operation. Overall
in good condition. Please note that the spare retort in one of the pictures below is
NOT included. Asking $75,000.00.
Item # C302 Mesh Belt Austemper Lines (2 available). Built by AFC-Holcroft
these are mesh belt, gas fired austemper lines. Parts to be processed are metered
on to the variable speed, 30” wide mesh belt, travel through an 8” long high heat
zone, drop into an electrically heated salt quench tank then are carried on a
conveyor out of the quench tank and into a washer. A circulating fan distributes heat
and atmosphere evenly though the heating area. Heat is supplied by two U shaped
radiant tubes that are recuperated. SSI controls monitor and control the atmosphere
gases. Furnaces were in operation until March 2015. One furnace is 1989 vintage
the other is a 2000 vintage. Both are complete, in very good condition and currently
in storage. Please contact us for pricing.
www.themonty.com
Item # C303 SECO/WARWICK Roller Hearth Furnace. This is a
SECO/WARWICK natural gas fired, roller hearth continuous atmosphere annealing
furnace with a controlled cooling section and exit purge vestibule manufactured in
2009. The furnace was designed for a net capacity of 367 pounds per hour of wound
transformer cores arranged on trays. The chamber length is based on processing
36” wide x 36” long trays with an average loading of 1100 pounds of cores/tray.
With an additional tray weight of 104 pounds for a gross load per tray of
approximately 1204 pounds. Nominal charge rate will be (1) one tray every 180
minutes. The heat/soak chamber is designed for a maximum operating temperature
of 870ºC (1600ºF), however normal operating temperature will be 825ºC (1520ºF).
The chamber will measure 5’-6” in length inside the insulation. The chamber will
have a nominal rating of 600,000 Btuh in a single zone of temperature control.
Following the heating and soak chamber there will be a controlled cool chamber with
a length sufficient to accommodate two loaded trays. The chamber will be kept at an
elevated temperature appropriate to achieve a cooling rate averaging 60ºC (114ºF)
per hour. Designed for a nitrogen-hydrogen protective gas atmosphere. The unit is
still fully operational but is currently mothballed. Asking $74,000 USD. Vendor will
dismantle and package for shipping.
Tempering/Anneal Furnace: 60"W mesh belt with support rollers. Furnace has a 35'L
heating section. Four (4) zones of control with four (4) roof mounted fans. Maximum
operating temperature is 1700°F. Total BTU's for the tempering/annealing furnace
3,790,000 BTU/HR. Please note that this furnace has two (2) different modes of
operation. Click on 'PDF" below for more information on the different modes of
operation.
The sequence of this furnace is as follows:
-
Load parts into pre-wash dump loader
Pre-Wash, 190°F, Gas Heat
Parts vibrate onto mesh (soft load) then onto cast link belt.
High heat cycle
Quench cycle, 200°F, Gas Heat, 8000 Gallon
Wash cycle, 190°F, Gas Heat
Temper cycle
Oil blackening cycle
Includes:
- 5600 CFH Air Cooled Endothermic Gas Generator
- SBS Air to Oil Heat Exchanger which consists of three (3) 5 H.P. fans.- Manuals &
Drawings
Very good condition, available immediately. Asking $650,000 USD.
www.themonty.com
Item # C301 Cast Link Belt Quench and Temper Line. Manufactured by Rogers
Engineering 4,000 pounds/hour cast link belt furnace line consisting of a 1750F high
heat furnace and 1700F temper furnace. Serial # CC-3977-0 (1997). High Heat
Furnace: 48"W Omega Cast Link Belt, 4" pitch, 3" sides. Furnace has a 30'L heating
section. Four (4) zones of control with three (3) roof mounted in the last three (3)
zones. Maximum operating temperature of the hardening furnace is 1750°F. Furnace
is radiant tube heated with recuperators. Furnace is currently set up for Endothermic
w/Enriching Natural Gas & Air. Total BTU's for hardeneing furnace is 3,180,000
BTU/HR. Controls; All mounted in a free standing panel includes Allen Bradley PLC
w/HMI Touchscreen, Honeywell UDC Digital Temperature Controls, SSi Carbon
Controls. Voltage 480/3/60/200kW.
Item # C296 C.I. Hayes High Temperature Tube Furnace. Model MY0002.528, 2-1/2" ID Tube x 28" Long Heating Chamber. Operating temperature of
1700ºC, 10.5 KW, Single Zone Control with overtemp protection. Overall dimensions
of 75" H x 32" W x 91"L. Hydrogen Atmosphere. Included is an automatic loader.
Asking Price $18,000.00 OBO
Item #C286 Wellman Mesh Belt Brazing/Annealing Furnace. Catalogue No:
40D411369AB61. Two zone heating (electric heating). High Heat 10' long, 1,120º
Celsius (2,050º F). 24'-0" open top water jacketed cooling. 12" clear height over the
belt. Overall dimensions: 69 ft x 5.7 ft x 7 ft. Silicon Carbide solid hearth with New
Stainless Steel mesh belt. Belt width 18", furnace hearth opening 20", furnace
hearth height 12". 3 phase 440 Volts; 150 KVA (for both zones). 6 GE transformers
(refurbished). 230 V – 10 A variable speed chain drive. The entrance vestibule has
been recently rebricked. Globars & silicon carbide hearth plates are excellent. Spare
globars are available. Good complete condition. Asking $29,000 USD.
www.themonty.com
Item # C299 Sunbeam Rotary Hearth Furnace. Working diameter of 6’, 8
station hearth, each station is 12” wide x 18” deep x 12 “ high. The door opening is
1’-6” wide X 10” high. Gas fired, 620,000 BTU’s, 3 radiant tubes and an operating
temperature of 1750F. Built in 1977 and used for neutral hardening. Also included
is a robotic arm for loading/unloading. The furnace is installed and in running
condition, brand new radiant tubes and a rebuilt fan. All manuals and drawings are
included. Good overall condition. Asking $40,000 USD.
Item # C284 CI Hayes Continuous Humpback Furnace. Built by CI Hayes in
1970 this furnace was rebuilt and rewired in 1986. Belt is 12” wide, 6” height
clearance over belt and has a heated length of 72”. Electrically heated, operating
temperature of 2100F. Two water jacketed cooling chambers, Molecular Dryer, 2
Ammonia Dissociators, Muffle is Inconel 600 as is the spare mesh belt. Currently
installed and can be started for a demonstration. Good operating condition. Asking
$60,000 USD.
Item # C283 Denton Thermal Systems (O'Brien & Gere) 2150˚F Rotary Hearth
Furnace System. Includes high temperature furnace, Nitrogen-Methanol Panel and
Quench Press. Working Zone: 6 ft Diameter Hearth, Door Opening is 14"W x 13"H
Overall Size: 9ft-8in Diameter x 10ft-10"Tall. Heating: Electric, 125 kW, 1 Zone,
Globar Heating Elements. Power Requirement: 200 Amps, 480V/3Ph/60Hz.
Temperature Rating: 2150˚F. Water Requirement: 3 GPM. Air Requirement: 100
www.themonty.com
Item #C285 AFC-Holcroft Atmosphere Pusher Furnace System. This system
was designed for hardening bearing races(up to 9” diameter). Built in 2000 is was
used for a little over 1 year before being shut down. This Furnace System is gas
fired, radiant tube, 4 zones, complete with alloy trays, atmosphere flowmeter panel,
oil quench press with air cooled oil and robotic handler, wash-off section, and belt
tempering furnace. The pusher is overall 15’ wide x 30’ long x 10’ high (ships in 3
sections). ID is 4’ wide x 50’ heated length (in “U” shape) x 10” high. Also included
is 3000cfh endothermic generator, a number of spare parts (including new radiant
tubes), robot handler, quench press and washer. Thi is a “single row” design but
the trays move inside the furnace in a “U” shape with an internal wall inside the
furnace (trays go up and back inside furnace and each length is 25’---- so there is
50’ total heated length). Each tray is 8.5” wide x 42.5” long x 2” thick---cast alloy.
Consider this in "mint"condition. Asking $395,000 USD which includes loading.
PSI. Controls: GE90 PLC. Honeywell Temperature Controller and Overtemp (missing
but will be replaced). Marathon Monitors Carbon Control System. Includes Quench
Press that was handling up to 5" Diameter bearings. Prior user reference available
upon request. Asking price: $79,000.00 USD. Location: Northeastern USA
Item #C265 Sunbeam Pusher Carburizer. This is a very unusual style of furnace
and perfect for carburizing of large gears, bearings or races. Working dimensions of
50" X 50" X 34" high. Operating temperature of 1750F. 3,000 pound capacity. Gas
fired 12 Honeywell composite single ended recuperated tubes (recently replaced).
Surface Casemate controls. 1800 gallon quench tank. System does not need a pit.
Comes with a spray washer, temper and an oversized IHRE air cooled quench oil
cooler. System is installed but not currently in use. Very good condition. Asking
$40,000 USD
www.themonty.com
Item # C269 CI Hayes Mesh Belt Brazing/Sintering Furnace.Working
dimensions of 5" over belt, 12” wide X 120” of heated length. Electrically heated
230/3/60, operating temperature of 2100F. Model LAC. Temperature controls are
new state of the art, control panel with Honeywell sold state digital readout
controller and overtemp for each of three zones, includes volt and amp meters. Full
alloy muffle in hot zone. 20’ long sealed water jacketed cooling. Globar heating
elements over and under the belt. (3) zones of control. (4) argon flowmeters.
Dayton AC inverter provides adjustable belt speed. Updated SCR controls. Muffle
and belt are new. Very good condition. Asking $39,000 USD.
Item #C219 ABBOTT MODEL 6ZSCR-18-432HH6-VC-2150. 18" wide belt, 3"+
opening over the belt, 432" heating chamber (silicon carbide muffles), six zones, 36"
long vari-cool with 162" of additional cooling including two curtain boxes. 2150
deg.F. max temp., piped for dissociated ammonia atmosphere and nitrogen purge,
335 kw @ 480/3/60,Honeywell UMO 800 controller/programmer, OAD: 84" w x 90"
h x 720" l. Currently used for annealing knife blades but with a little effort a metallic
muffle in the front half of the heating chamber could be added for debinding and
sintering of PM parts. Asking price: $77,000 USD OBO.
www.themonty.com
Item #C256 Surface Combustion Rotary Hearth Furnace Line. This system
was designed for heat treating and straightening crankshafts and consists of a
rotary hearth furnace, 2 Gleason straightening presses and a robot for
loading/unloading. The furnace is S/N CC11590-1 with an outside diameter of 17'
3", inside 15', inside height of 2' 11" with an overall height of 8" 6". Built August
1979. Gas fired with 8 trident tubes. Atmosphere is Endo/Natural gas. Nominal tray
size is 5" X 21", number of tray positions 60, tray loader/unloader length 10' 6".
Hearth has ceramic tray support and guide tiles and embedded in 12" thick
insulating firebrick. Sidewalls consist of 9" of insulating firebrick backed with 4 1/2"
of insulating block. Alloy and brickwork are both excellent. Gleason straightening
presses are Model 140 units, oil quench machines with 6' cabinet, indexing table,
S/N's 107902 and 118701 with chilling system consisting of C/C tank, 5' X 5' X 3', 3
7 hp pumps, controls and cooling tower. Also included is a ASEA Model S2 robotic
loading arm, with robot controls, joystick touch pad controls. S/N 4955-8127-001.
System is complete, installed but not in operation. Asking $150,000 USD for the
furnace.
Draw/Temper
See something you need, click on the link or scroll through all the items for sale. Searching
for something we don’t have listed, fill out our Contact Form.
•
•
•
•
•
Aluminum Aging Oven
Aluminum Drop Bottom Dual
Oven System
AOV Small Aluminum Drop
Bottom Oven
Grieve Electric Oven
Grieve Electric Oven
Large Box Tempering Ovens
(4 available)
Lindberg Box Draw Furnace
•
•
•
•
•
•
•
Leads & Northrup Steam
Tempering Furnace
Lucifer Furnace
Pifco Temper Furnace
Recirculating Walk-In Oven
Rolock Box Temper Furnace
Tempering Ovens 36" X 48" X
36" (2 available)
Williams Temper 48" x 48" x
36"
Item # T319 Temper 48" W X 48" D X 36" H. Manufactured by Williams in
1999. Gas fired, burner box, operating temperature of 1500F. Fan included but
needs to be installed. Some misc., components missing and minor repair required.
Asking $29,000 USD.
Item # T318 Large Box Tempering Ovens (4 available). Built by Eisenmann in
2002, Model # HN-FNC-002. Working dimensions of 108” Wide x 96” Deep x 64”
High. Natural gas fired, 3.2 million BTU’s per hour. Operating temperature of 1200F.
Description; Stainless Steel Lined Recirculating Box Tempering Oven complete with
Top-Mounted Alloy Recirculating Fan (20 HP – 13,000 CFM), Rear-Mounted Heater
Box with Eclipse Burner System, Alloy Skid Hearth, Forced Cool Down Fan System
(7,333 CFM), Vertical Rising Motor Driven Front Door, and Stationary Loading Table.
www.themonty.com
•
•
Instrumentation; Free Standing Control Panel with Eurotherm Digital Set Point
Programmable Temperature Controller, High Limit, Chessel Strip Chart Recorder,
and Honeywell Flame Safety System.
Item # T317 Aluminum Aging Oven, Manufactured by Oliver Machinery
Company, Model B-9650. Working dimensions of 50’ long X 9’ wide X 6’ high.
Natural gas heating, 2.5 BTUH with an operating temperature of 365F and a
maximum operating temperature of 500F. Temperature uniformity of +-15F.
Maximum oven load is 15,000 pounds. Doors at either end to allow for
loading/unloading. Currently installed and in very good condition. Asking $29,000
USD plus removal costs.
Item # T316 Grieve Model# HX-1000 Electric Oven. Max. Temp: 1000ºF, +/10ºF Uniformity. Circulated Air: 1000 CFM, 3/4 H.P. Fan Motor. Insulation
Thickness: 8". Single door. Rated Work Zone: 38"W x 20"D x 26"H (Measures
36"W x 19"D x 25"H). Power Rating: 20 kW. New Upgraded Controls: Temperature
- SSI Series 7 7EK (Super Systems, Inc.) Hi-Limit - SSI 7SL. Outside Dimensions:
62"W x 40"D x 61-1/2"H (new dim.). Approx. Shipping Wt.: 2740 lb. Asking
price: $8,900
www.themonty.com
OVERALL DIMENSIONS: Oven: 13’ Wide x 20’ Long x 17’8” High (includes Door
Structure. (Shipping Dimensions: 12’6” Wide x 20’ Long x 10’8” High). Loader:
9’6” Wide x 12” Long x 4’ High. Approximate weight 20,000 pounds. Excellent
condition, operational. Asking $62,500 USD each.
Item # T315 Grieve Model# HX-1250-E, Electric Oven, Max. Temp: 1250ºF,
+/- 10ºF Uniformity. Circulated Air: 1400 CFM, 1 H.P. Fan Motor. Insulation
Thickness: 10". Single door. Rated Work Zone: 38"W x 20"D x 26"H (Measures
36"W x 19"D x 25"H). Power Rating: 30 kW. New Upgraded Controls: Temperature
- SSI Series 7 7EK (Super Systems, Inc.) Hi-Limit - SSI 7SL. Outside Dimensions:
66"W x 44"D x 65-1/2"H (new dim.). Approx. Shipping Wt.: 3300 lb. Asking
price: $ 10,900
Item # T310 Leads & Northrup Steam Tempering Furnace, Cat # 9512-15,
Work Zone: 11.5” Dia. X 15” Deep, RA 330 S.S Retort, Nichrome Heating Elements,
Max Operating Temperature 1250 F, Complete With One Basket / RA 330 S.S. With
Three Trays, Chart Recorder Panel, 10 LBS./ HR Steam Required, 240 Volt, 1 H.P, 3
Phase Motor, 240 Volt, 15 KW, 1 Phase Heating Elements. $8,900 USD.
www.themonty.com
Item # T312 Recirculating Walk-In Oven. Manufacturer: Despatch. Inside
Dimensions: 66”high x 54”wide x 68”deep. Heated: Gas fired. DG-300 Heater.
Temperature: 650 deg.F. Model Number: V-41. Serial Number: 96267. Temperature
Controls: Partlow indicating controller and overtemp. Description & Features: Double
swing open doors, horizontal air flow, insulated floor with tracks for a cart, powered
exhaust blower, top mounted combustion and fan chamber. Atmospheric type
burner system. Complete combustion controls and safeties. Oven will be cleaned
and painted, checked out and test fired prior to shipment. Asking Price:
$16,500.00.
Item # T301 Lucifer Furnace, Model Number 46GT-R36, Serial Number 6418,
Working Dimensions of 24” w x 36” d x 24” h. Insulation and elements are in good
shape. Front lift door with a foot actuator. Controls: Honeywell round chart recorder,
Honeywell overtemp, No controller. Power: 460/3/60 28 Kw 35 Amps, Temperature:
Max 1650° F. Nitrogen Atmosphere. Price: $14,500.00 USD as is, where is.
Item #T290 Tempering Ovens 36" X 48" X 36" (2 available). Working
dimensions of 36"W x 48"D x 36"H. Shells have just been completed and buyer has
the option of Gas-Fired or Electric, Hearth Height, Burner Locations (Left or Right)
and Panel Location. These can be completed, fully tested and ready to ship to your
facility in 8-9 weeks at a very attractive price. Please call for pricing.
www.themonty.com
Item # T303 Pifco Temper Furnace. S/N 8177 built in 1988. Working
dimensions of 126" long x 60" wide x 40" high. Overall dimensions of 13’ x 11’ x 11’
high. Comes with load and unload discharge tables and combustion fan. Maximum
operating temperature 950 deg. F. Rated for 250 pound net weight x 37.4in long
tray loaded every 15 minutes. Furnace holds three (3) trays. Approximate nineteen
(19) minutes to operating temperature. Forty-five minutes in furnace @ 15 minute
load cycle. Heated by one gas burner approximate rating 600,000 BTU/hour. Utilities
required: 1000 BTU natural gas @ 5PSI, 480v 3Ph 60Hxz. Water 80 deg. F
maximum @ 20PSI. Compressed air 60PSIG minimum. Adequate drain for water.
Good condition. Asking $38,000 USD.
Item #T288 AOV Small Aluminum Drop Bottom Oven: AOV Model: DBF-3X3E, Electric Heat, Work Zone undefined, but is probably 3ft Dia. x 3ft H based on
model number. Includes Quench tank. 1200˚F. Asking price: $ 18,000 USD.
Offers Considered. Location: Western U.S.
Item #T286 Lindberg Box Temper. Model 11-7212048-G14, S/N 24947. Working
dimensions of 72” wide X 120” long X 48” high. Gas fired with a maximum operating
temperature of 1200F. Vertical lift-air operated door, brick lined, 5 course refractory
hearth, alloy roof baffles, alloy side wall ducts, dual zone burners-roof mounted
combustion chambers with dual belt driven fans. Free standing prewired control
panel. Good condition. Asking $65,000 USD
Item # T282 Rolock Box Temper Furnace. Model 1515. S/N 8697.7.92. Working
dimensions of 36'W x 30"H x 60"L. Electrically heated 480/3/60/120 kW. Operating
temperature of 1400F. External Dimensions: 91"W x 96"L x 109"H without stand.
Controls: Controls are located in a separate NEMA 12 single door enclosure with
flange mounted disconnect handle. Honeywell UDC 3000 digital temperature
controller, a Honeywell UDC 2000 digital high limit and a Honeywell DR-4500 "Truline" round chart recorder are flush mounted in the door of the enclosure. Control
switches with indicating lights are also flush mounted in the door of the enclosure.
Non fused disconnect switch, Halmar SCR power controller, high limit contactor,
motor starter etc. are mounted inside the enclosure. Description: Air operated
www.themonty.com
Item #T287 Aluminum Drop Bottom Dual Oven System: Wisconsin Oven, Dual
Oven Aluminum Drop Bottom Solution Treating System, 2 Ovens, Quench Tank,
Rinse Tank, Platforms, Doors, Chiller, Power Supplies, Controls, Work Zone: 8ft W x
8ft D x 8ft H each oven, Temp. 800-1200˚F, 30 H.P. Recirculation Fan, Electric, 288
kW each, 346 Amps each.Price: $ 105,000 for all Offers Considered
www.themonty.com
vertical lift door with counterweight assist opens to allow full access to the interior.
Door is operated by push button controls in the control panel. Furnace is lined with
ceramic fiber and has a stainless steel air duct shroud to direct the air and protect
the heating elements which are located on both side walls. Belt driven circulating fan
is mounted through the top of the furnace. Heated air is circulated down both sides,
under the hearth rails and returns through the roof for good uniform heating. Three
hearth rails on the floor support the work load. Nitrogen atmosphere inlet tube is
mounted through the rear wall. Two finned heat exchanger pipes are mounted on
both sides with a blower to provide faster cooling. Good condition. Asking
$42.500.00 USD.
Generator
See something you need, click on the link or scroll through all the items for sale. Searching for
something we don’t have listed, fill out our Contact Form.
•
•
•
•
•
•
•
•
•
3600 CFH Endothermic Gas
Generator
3600 CFH Endothermic Gas
Generator
Ammonia Dissociators (4
Available)
Can-Eng Endothermic
Generator
Endothermic Generator 9,000
CFH
Exo Generators (2 available)
Gasbarre.Sinterite Endo
Generator
Lindberg Endo Generator
Lindberg Heavy-Duty Endo
Generator
Pacific Scientific Endothermic
Gas Generator
•
•
•
•
•
•
•
Surface Combustion 3600 CFH
Endo Generator
Surface Combustion Endo
Generator
Surface Combustion 2400CFH
Endo Generator
Surface Combustion 5600 CFH
Generators (3 available)
Surface "Multi-Bottle" Endo
Generator 6000 CFH
Surface "Multi-Bottle" Endo
Generators
Surface 2400 CFH Endo
Generator
Item # G194 Endothermic Generator 9,000 CFH. Manufactured by the JL
Becker company this is a 3 retort, 9,000 CFH endothermic generator. Designed so
that each retort can be shut down independent of the others. Air cooling. Control via
PLC with touch screen interface. Currently installed but not in operation. Complete,
in good shape and ready to operate. Asking $75,000 USD.
Item # G193 Pacific Scientific Endothermic Gas Generator. Natural gas, Model
# PGF 3000-EN, Serial #416417, Max Temp 1950°F, Voltage 460/3/60, Work Area
3000 CFH, Dimensions: 42'W x 86"H x 106"L - Approx. Standard "Pacific Scientic"
design Endothermic Gas Generator with water cooled shell & tube heat exchanger,
Waukee vane pump, Waukee flow meters, atmospheric type ring burner. Generator
just removed from service on 4/2015. Controls:Mounted and wired in an enclosure
attached to the generator includes a Honeywell programmable logic controller (PLC)
which controls all functions of the generastor. The PLC also monitors/controls
www.themonty.com
•
temperature, dewpoint and flow. There is a Honeywell digital high limit mounted in
the same enclosure. This generator has a "Waukee" rotary vane pump and
"Waukee" ratio tronic digital flow controls. This generator is also equipped with a
"Nova" dewpoint system. Available immediadely and in very good condition FOB
East Chicago, IN. Please call for pricing.
Item # G191 McLaughlin Services 3600 CFH Endothermic Generator. 3600 CFH
Endo generator manufactured by McLaughlin Services in 2014. Natural Gas: 4,000
CFH, 5 psi maximum, Electricity: 40 Amps, 480V/3Ph. Base unit includes framing for
central equipment for the following components, supporting up to (2) additional
expansion cells, 3,600 CFH each: control panel, mixer assembly, burn-out blower,
main NFPA gas train, fire check valve, Vent Burn-Off, and 3-way valve to direct gas
to the heat treat furnaces. Additionally, the shell is constructed to support a single
air cooler, sized for 3,600 CFH Endo gas. The shell design features a low headroom
requirement for retort removal and replacement. Inside shell plate is a 12” ceramic
fiber lining, providing an average outside skin temperature of 150°F. Generator is
equipped with (1) cast HU alloy retort. The retort incorporates a simple, easy to
remove end plates for fast catalyst replacement. Atmosphere Engineering
EndoInjector™ system. This mixer design features electronic flow measurement and
control. The EndoInjector has a large turn-down capacity for an economical ondemand production of gas and precision Dew Point control. The mixer is sized for
quick conversion for system expansion. A Maxon manual safety valve is used to
supply natural gas to the mixer. This arrangement helps ensure operator visual
check of equipment before starting the generator. SBS End-o-Cooler air cooled gas
cooler cools the gas exiting the generator. The air cooled design eliminates water
fouling of the tubes, leaks, and potential damage to the generator. The cooler
features a straight-thru design for easier carbon clean out. Asking $92,000 USD.
www.themonty.com
Item # G192 Lindberg Hevi-Duty Endo Generator. Lindberg endothermic
generator. 1500 CFH. Fair condition but complete. Asking $7,000 USD.
Item # G189 Surface Combustion 2400 CFH Endo Generator. Two retort
"multi-bottle" configuration allowing one retort to operate while the other is shut
down for maintenance. New in 1995. S/N AC-43349-1. 2400 CFH capacity.
Casemate controls, air cooling. Good condition. Currently installed and in operation
but will be available shortly. Asking $59,000 USD.
Item # G188 Surface Combustion 2400CFH Endo Generator. Size S-2N, S/N
413E. Maximum operating temperature of 1950F. Natural gas heated. 575 volts/3
phase. 1970’s vintage. SBS Endotherm cooler and SSI atmosphere controls. Catalyst
and retorts are in good condition. Overall in very good condition. Currently in
storage. Asking Price: $25,000 USD
Item # G187 Surface Combustion 3600 CFH Endo Generator. Size S-3.
Maximum operating temperature 1950F. Built October 1978. 575V/3phase/60 cycle.
Three tube unit with fairly new catalyst and retorts. SBS Endothern air cooler for gas
www.themonty.com
Item # G190 Surface Combustion “Multi-Bottle” Endo Generator. Built in
20015. 6,000 CFH, 2 retorts. Model # RX-2T-ABES, S/N CU-12592. Excellent
condition with new catalyst. Also included is a brand new spare mixing pump.
Asking $50,000 USD as is or $75,000 repainted with a new SSI atmosphere
control system and new retorts.
and SSI atmosphere controls. Currently in storage. Overall in good condition.
Asking $29,000.00 USD.
Item # G182 Manufactured by Surface Combustion this is a gas fired 3600 CFH
Endothermic Gas Generator. New catalyst recently and comes with 4 spare new
North American burners. Ser. No. C-3875-1. Max. Temp.: 2050˚F. 720 cu. ft/hr
fuel usage@ 5 PSI Pressure. Super Systems Carbon Probe on carbon control system.
Operating condition. Asking $24,900.00 USD.
Item #G178 Ammonia Dissociators (4 available). Built by Sargeant & Wilbur,
4 electrically heated Ammonia Dissociators. Model GAD3000E. 3,000 CFH capacity.
Maximum temperature 1759F. Voltage 480/3/60/60 kW. External dimensions of 5'W
x 6'H x 8'L. Controls: Mounted and wired in a free standing panel includes the
following:
- Yokogawa UT 350 digital control for dissociator undertemp.
- Yokogawa UT 350 digital control for dissociator overtemp.
- Yokogawa UT 350 digital control for dissociator temperature control.
- Two(2)Yokogawa UT 350 digital controls for vaporizer lower/upper zone.
- Yokogawa UT 350 digital control for vaporizer overtemp.
- All necessary signal lights, timers etc.
Mounted in the same control cabinet are three (3) SCR's. Two (2) "Halmar Robicon"
and one (1). "Ametek". One is for dissociator heating elements and the other two
are for vaporizer lower/upper zone heaters.
www.themonty.com
Item # G183 Can-Eng Endothermic Generator. Single retort 3600 CFH capacity.
Unit is complete and installed. SSI controls with AC-20 controller. Also includes air
cooling. Good condition. Asking $5,000 USD or best offer.
Item # G177 Surface Combustion Endo Generator. Model TI-RX Gas Generator.
S/N J467E. 1200 CFH capacity. Manufactured in 1980. Reasonable condition.
Asking $4,900.00.
Item # G176 Surface "Multi-Bottle" Endo Generators. Manufactured by
Surface Combustion. Natural gas heated 675 CFH/HR. Model # RX 35-75-3V.
Maximum temperature 1950F. 7500 CFH capacity. Controls are complete, water
cooled. SSi atmosphere controls and Atmosphere Engineering "EndoInjector". Very
good condition, ready to go. Asking $75,000 USD.
www.themonty.com
Description: Electrically heated Ammonia Dissociator suitable for supplying up to
3000 CFH of atmosphere with a composition of 75% Hydrogen and 25% Nitrogen.
This atmosphere is obtained by cracking anhydrous ammonia vapor in a catalyst
filled vessel maintained at a temperature of 1700°F to 1850°F. Incoming ammonia
pressure is reduced before retort entry. At the outlet of the retort the hot
dissociated ammonia passes through a dry cooler where the gas is cooled to near
room temperature. It then passes through a flowmeter and on to the consuming
device. This dissociator includes a Sargeant & Wilbur Ammonia vaporizer. This
dissociator is provided with two (2)catalyst filled heat resisting alloy retorts. The
retorts are mounted within the insulated dissociator heating chamber. The heating
chamber consists of heavy Mullite T-Slot tiles. Retorts are heated with Sinuouswound Nichrome Ribbon Heating elements which are mounted in the tile slots. The
element tails and studs extend through the rear wall of the dissociator. Elements
can be removed throught the rear wall without having to unpack furnace insulation
etc. A step-down transformer (480V to 240V 112.5 KVA) is included. Manuals and
drawings are also included. Very good condition. Asking $29,500.00 USD each.
Item # G174 Exo Generators (2 available). Model 9328312-G2, manufactured
by General Electric. Gas fired, 1500 CFH capacity. Standard rich exo design. Units
have newer Waukee flow meters. Selas pump, burner and fire check valve. Updated
Honeywell digital controls for temperature, water and alarms. Good condition.
Asking $9,500 USD each.
Item #G172 Surface Combustion 5600 CFH Generators (3 available). Model
T3N-RX. Gas fired, 5600 CFH capacity. Operating temperature of 1950F. Standard
Surface Endothermic Generator complete with 3 retorts, Spencer Blower, Waukee
flowmeters, Roots pumps and water cooling. Control panel with Barber Coleman 560
Digital Temperature Controller and L & N Strip Chart Recorder. Overall dimensions of
8' wide X 11' long X 11' 6" high. Approximate weight 12,000 pounds. Very good
condition. Asking $33,500.00 USD each.
Item #G169 Gasbarre/Sinterite Furnace Division Endo Generator. 3000 CFH,
electrically heated 460/3/60/63 Amps/50kW. New in 2006. External dimensions of
106" wide x 75" deep x 116" high. Controls are enclosed in a panel attached to the
side of the generator. Honeywell UDC 3200 digital temperature controller and
www.themonty.com
Item #G173 Lindberg Endo Generator. 4500 CFH, gas fired. Retorts and
brickwork are in excellent condition however it requires temperature controls and an
air cooler (vendor has partially completed changing from water cooling to
air).Asking $17,500.00 USD.
www.themonty.com
Honeywell UDC 2500 digital high limit safety. Control switches with indicating lights
are flush mounted in the enclosure. Flange mounted fused disconnect switch for
control power. Separate non fused disconnect for the main power. Waukee flow
meters are manifold mounted for incoming and outgoing gases. Flow meters
include: Natural Gas 0-1000 CFH, Air 0- 2500 CFH, (3) Mixed Gas 0-1500 CFH and
Endo 0- 3500 CFH. Step down transformer for reduced voltage to the heating
elements. Electrically heated 3 retort generator. Refractory lined shell with vertically
mounted retorts. Total of twelve (12) silicon carbide heating elements, 6 on each
side are mounted through the chamber for good uniform heating of the alloy retorts.
The natural gas and air pass through a Waukee "mixor" valve then into the Waukee
gas pump. Mixed gas enters the 3 "mixed gas" flow meters, through the Selas fire
checks and enters the top of the retorts. The gas travels through the catalyst filled
heated retorts and exits at the bottom. The exiting Endothermic gas passes through
water cooled chambers then finned cooled air heat exchangers then through the
Endothermic flow meter. A pressure regulator is supplied on the exiting gas piping.
Good condition. Asking $29,500.00 USD.
Induction
See something you need, click on the link or scroll through all the items for sale. Searching
for something we don’t have listed, fill out our Contact Form.
•
•
•
•
•
AEG Elotherm Induction Billet
Heater
Ajax Tocco Power Supply
Ajax Tocco Power Supply
(unused)
Induction Furnaces
Induction Power Supply
Induction Hardening/Press
Quench System
•
•
•
Induction Power Supply
Induction Press Quench
System
Raydyne Induction Heating
System
Item # I169 Induction Power Supply. Pillar Mark 11 100 kW, 10 kHz Induction
Power Supply. Manufacturer: Pillar. Input Voltage: 480/3/60/133 Amps/111
KVA/.95 P.F. Output:100 kW, 10 kHz. Output Voltage: 440V or 800V . Model:
AB7104-108/MK11. Serial Number: 6414 IAT. Includes a full set of spare boards.
Good condition and ready to go. Asking $19,500.00 USD.
Item # I168 AEG Elotherm Induction Billet Heater. Type BTH 2/6005 NC, S/N
4022226, Year of Construction 1999. 2400 KW Nominal Output. Complete and in
good condition. Used for inductive heating of ferromagnetic material to forging
temperatures of about 1250C. Able to handle billets 95-350mm long X 60-115mm.
Asking $59,000 USD.
www.themonty.com
•
Power Supply:
•
•
•
•
Ajax / Tocco Model # Pacer T ; 400 KW, 1000 HZ solid state power supply,
Manual control; Serial numbers: manufactured in 2012, 2 power lead taps
per power supply.
Water cooled power leads, 2 sets per power supply; 1 set at 25’ and 1 set at
35’per power supply.
Each power supply has its own cooler system for the power supply
Water flow requirements 456 GPM at 30 psi.
Coil Information:
•
Coils are 88 “ in height and 58 “ in ID, were used in a free standing
application
Silica Carbide Rings:
•
•
6 SiC Super Rings support each coil; each ring is 56 “ OD x 54 “ ID x 16 3/4 “
Tall
Rings were purchased from Allied Mineral Products , are defined as Micron
56”x52”x16” tall; rated to support 2700 0 C process temperature
Susceptor, Graphite Tile:
•
A multi-piece graphite tile susceptor supports each coil. Installed working
zone of furnace is 40 “ I.D. x 80 “ tall.
Water Recovery System:
www.themonty.com
Item # I167 FMI currently has 8 each complete Induction Furnaces with 4 power
supplies each supporting two furnace coils. Each power supply has two sets of
power leads to connect to the coils. Coils are free standing units that have never
been grouted, they are used with silica carbide rings, 6 rings support each coil. A
graphite tile susceptor is used within the silica carbide rings, insulated with carbon
black insulation. A technical description of the furnace systems follows.
•
•
Baltimore Air Cooling water recovery cooling system, model no. 3527C, serial
number U123074701-01, belt # BR-B128 (Larger System)
Baltimore Air Cooling water recovery cooling system, model no. 15219, serial
number U1147792901-01-01, belt # 3R-B120 (Smaller System)
Input Ratings:
Volts Min./Max. : 432/528
Amps.Max. : 291
Freq.Hz. : 60Hz
Output Ratings:
Volts : 512
Amps. : 389
Freq.Hz. : 3/10 KHz
P.F. : 82
KVA : 220
Phase : 3
KW : 150
Phase : 1
This unit was sold new to Caterpillar in 2006 and never installed and never used.
Excellent condition. Asking $33,000 USD.
Item #I162 Induction Press Quench System. EDMS Industrial Induction
Heating and Die Quench, New in 2003, 400kW Output Supply, 3kHz Frequency. This
machine is currently being used to reheat and die quench spiral bevel ring gears up
to 500mm in diameter. Installed to replace the rotary furnace and isolated die
quench processes. This machine is designed with an automatic conveyor and loading
system to continuously heat, die quench, and temper 500mm rings. This unit has an
EFD 400kW output supply with a 1.7-3.0 kHz frequency designed for deep and fast
heat penetration which allows rings to be heated and die quenched in just minutes.
This system has an added setup to convey quenched parts to and through a
continuous Apar IPSEN tempering and preheat electric furnace with a 36" x 48"
opening with a 3,000 lb load capacity. This unit also comes complete with its own
outside cooling system and monitoring to ensure flow, min/max pressure, and
www.themonty.com
Item # I164 Ajax Tocco Induction Power Supply. Model #OL-426-150-3/1000M. Manufactured 12/06. Serial Number: 46-1128-11. Wiring Diag.: WD-287513.
CKT.BKR.AMPS. : 400.
min/max temperature. This fully integrated system allows the flexibility to handle
parts from 125mm to 500mm diameter. The transfer time is presently 5-6 seconds
from induction to quench. The pick and place system can be upgraded by purchasing
and utilizing a robot to allow for faster transfer time, for thin wall parts. Thus
allowing the induction and quenching of bearings, cones, and cups, as well as, outer
rings and end rings.
Item #I160 Ajax Tocco Power Supply (unused). Ajax Tocco Inductron PT
power supply, capacity: 450kW. Frequency: 3-10 kHZ. Output Voltage: 400 *. Year
of manufacture: 2006. This unit was never installed and is unused. *Price quoted
from Ajax Tocco to convert output voltage from 400 to 800 including parts and labor
is
$15,230.
http://www.ajaxtocco.com/applications/documentlibrary/Inductron%20PT_092003.p
df New this unit was $86,000 USD, asking $49,000.00 USD.
Item #I158 Induction Power Supply. Manufacturer Inductoheat /Elphiac.
Model Number: DC18T+HF08. S/N 2177DC. 335 kW, 200 kHz, 750V Output.
www.themonty.com
Conversion available to make this unit a Heat and Quench station with variable high
frequency independant of the Die Quench.
MACHINE SPECIFICATIONS:
* Output Supply
400kW
* Frequency
1.7-3kHz
* Max Diameter
500 mm
* EFD Power Supply
* Power Requirements
3 x 480v - 60Hz - 570KVA
* Dimensions (L x W x H) 1790mm x 1200mm x 1730mm
* Weight
15500 kg
*Customer paid over $1,500,000.00 in 2003
Input Voltage: 460/3/60/448 KVA/562 Amps. Output Voltage: 335 kW/750V/200
kHz. Very good condition. Asking $39,500.00 USD.
Item #I153 Raydyne Induction Heating System. Input Voltage: 480V/3
Phase/60 Cycles/110 Amps, Output Voltage: 40 kW, 450 kHz, Year Built: 1985,
Model of Power Supply: EI-40, Serial Number of Power Supply: 41408901-B. Please
note the RF Tube is missing. Includes a dual heat station with quench. Model of
Heating/Quench Station: 10228201, Serial Number of Heating/Quench Station:
10228201B. This system is Government Surplus and appears to be fairly clean
inside power supply cabinet. The power supply has a "Control Concepts" SCR power
controller. Asking $7,500.00 USD.
www.themonty.com
Item #I154 Induction Hardening/Press Quench System. Manufactured by
Robotron (now part of EFD Induction) this system was designed to heat treat
synchronizer sleeves. Parts are heated with Induction and with a pick and place
unit placed in a die, where they are quenched in a die and quenched. Parts maintain
perfect shape. 100 Kw 10KHz Robotron power supply. System is complete and in
good operating condition. Best offer.
Miscellaneous
See something you need, click on the link or scroll through all the items for sale. Searching
for something we don’t have listed, fill out our Contact Form.
•
•
•
•
•
•
•
•
AFC Charge Car
Berg Water Chiller
Cryogenic Unit (3)
Cryogenic Unit
Dry Coolers Pumping Station
Dual Lane Conveyor Washer
Dunk/Spray Washer
Electric 4 Stage Conveyor
Washer
Endothermic Generator
Retorts
Gibson Tumblast
Georg Fischer Shot Blast
System
Goff Tumblast
Guyson Table Blast
Guyson Shot/Grit Blast
Machine
Holcroft Dunk/Spray Washer
Hunterdon VRT
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Ipsen Automatic Dunk/Spray
Washer
Liquid Nitrogen Tanks (two
available)
Marley NC Cooling Tower
NU-BIT Cryomersion 1500
Pangborn Rotoblast
Pit Furnace Fixturing
SBS Unit
SBS Quench Air
SBS Quench Airs (2 Available)
SBS Quench Airs
Shot Peen System
Spectra-Tech 0044-003
Infrared Microscope
Surface Combustion Parts
Washer
1 Surface Combustion Radiant
Tube and 4 Supports
Wheelabrator Rubber Belt
Tumblast
Item #M379 Georg Fischer Shot Blast System. This unit is currently installed
and in very good condition. Included are $10,000 worth of spare parts. Asking
$20,000 USD.
Item #M378 1 Surface Combustion Radiant Tube and 4 supports. Brand New
the cost was $1,844 for the tube and $448 each for the supports for a total of
$3,636 in 2014. The radiant tube is Surface Combustion inventory # 850628 and
the support is part # 70R64/L. They are a set for a Standard Allcase furnace. One
www.themonty.com
•
•
•
•
•
•
•
•
leg of the tube is 3/12 inches in diameter and 62 inches long. The other is 4 ½
inches in diameter and 60 inches long. Asking $3,000 USD.
Item #M376 Dunk/Spray Washer. Manufactured by Williams in 1999. Electrically
heated with working dimensions of 24" X 36" X 20" high. Allen Bradley PlC control.
Asking Price: $2,000 USD.
Item #M375 Goff Tumblast. 6 Cubic foot capacity. Rubber Belt Tumblast
w/Integrated Dust Collector. No loader. Asking $20,000 USD.
Item # M374 Guyson Table Blast. Model GWB-401T. 40” diameter x 16”H.
Includes Integrated Dust Collector and Allen Bradley PLC Controls. Asking
$12,500.00 USD.
www.themonty.com
Item #M377 Marley NC Cooling Tower with SPX Cooling Technology: Two
cell unit SPX NC8400 (each cell has 540 Tons of cooling for a total of 1080 Tons of
cooling). Marley is the premium brand in the cooling tower industry. Very good
condition with only two years of operation, and were sold when the furnaces it was
supporting were sold. The Marley Cooling towers are currently ready for immediate
delivery. Priced to sell. Sale price for one cell unit: $22,500. Sale price for both
units: $40,000
Item # M372 Pangborn Rotoblast. Pangborn® Rotoblast® Barrel Model 12GN.
12 Cubic Feet Rubber Belt Tumblast w/Loader & Dust Collector. Good condition.
Asking $30,000 USD.
Item # M371 Dry Coolers Pumping Station. Medium sized Dry Coolers closed
loop water cooling system. Installed and complete. More details to come. Asking
$7,500 USD.
Item # M370 SBS Quench Airs (2 available). Manufactured by SBS Corp., these
are air/oil quench oil coolers. Each is a 3 fan unit with disconnect and 480 volt.
Suitable for a large continuous line. Installed indoors. Very good condition. Asking
$12,500 USD each.
www.themonty.com
Item # M373 Gibson Tumblast. 6 Cubic Feet Rubber Belt Tumblast. No loader or
dust collector. Good condition. Asking $15,000 USD.
Item # M369 Guyson Shot/Grit Blast Machine. Machine Model RXS-400, rotary
system, Serial Number M53868, Model 75/12 Cyclone Media reclaimer and D-1000
Dust collector. Purchased news in 2011 and put into service in 2012. System is
complete and in excellent condition. New thiswas $83,000 USD, asking $32,000
USD.
Item # M366 Wheelabrator Rubber Belt Tumblast. Model # TBR-12, Serial #
A142403, Voltage 480/3/60, 12 cubic feet, Controls - complete. Available
Immderiately, very good condition. Please call for pricing.
Item # M365 Manufacturer: Grapar. Type: Dual Lane Conveyor Washer.
Heated: Natural Gas. Dual Lane Washer Serial Number: 08-010 (2008). Max
www.themonty.com
Item # M367 Electric 4 Stage Conveyor Washer. This washer has four (4)
stages which consists of 4' wash, 3' rinse, 2' rinse, 5' dry off. All stages are
electrically heated. Each tank has a 300 gallon capacity. Washer is constructed of
stainless steel and has spray nozzles located on top, both sides and bottom.
Stainless steel mesh type conveyor belt is rod reinforced and has 1-1/2"H guard
edges to keep parts from falling off the belt. A 10'L discharge conveyor with variable
speed is included with this washer. Manuals and drawings are included. Model
#PDW-49, Serial #2419, Voltage 460/3/60/145 FLA, Work area 21 -1/2"w x 15"h,
Dimensions 65"w x 96"h x 21'l. Controls: Mounted and wired in an enclosure
attached to the washer includes automatic digital heat timer, master power light,
low level light, heaters on light, pump selector switch for agitate/auto spray, master
power on button, selector switch for skimmer on/off, selector switch for heat mode
"auto/manual", start push button for pump, master power off button, stop push
button for pumps, "E-Stop Button. Dial to control conveyor speed. Available
immediately and in very good condition FOB River Rouge, MI. Please call for
pricing.
Item # M364 Hunterdon VRT - This Variable Reactance transformer consists of a
set of (3) individual transformers that were connected to power a Surface
Combustion Super Allcase furnace to produce a 120 KVA output to heat the
elements in the furnace. The units are water cooled with a primary input of 480
Volt, three phase,. The power is regulated with a Halmar DPA – 1 30 amp that is
SCR controlled and uses a 0-10 volt input that is provided a separate controller, for
example, a Honeywell 2000. Gross weight 3-4000 lb. Asking $2,500.00 USD.
Item # M363 SBS Unit. Specs: S/N: 4926. Year: 2007. Three (3) Fans with side
mounted disconnects. Overall Size: 6'w x 6'h x 21'l. W-RES, MAWP 75 psi @ 450°F,
MBMT -20°F, 75 psi. Price: $17,500.00.
Item # M362 Liquid Nitrogen Tanks (two available). Excellent condition
asking $1,000.00 USD each.
www.themonty.com
Temperature: N/A. Voltage: 480/3/60. Work Area: 11"W x 7"H. Each Lane External
Dimensions: 8'W x 10'6H x 30'L - approx. Controls: Mounted and wired in an
enclosure attached to the washer. Includes an Allen Bradley MicroLogix 1200 PLC
and an Allen Bradley "Powerflex 4" VFD to control conveyor belt speed. Description:
This washer has three (3) stages, wash/rinse/blow-off. This washer is gas fired
using Eclipse burner and gas train with a Honeywell UDC digital temperature control.
Spray nozzles are located on top, both sides and bottom. Condition: Very Good.
Please call for pricing.
Item # M360 SBS Quench Airs (2 available). Model 3085-4, Serial numbers
2450 and 2451, 575 volt. Both in very good condition. Best offer.
Item # M357 Shot Peen System. USF Surface Preperation single station, 10 gun
(up to 10 nozzle) suction blast/ shot peen cabinet. This unit is in fantastic working
condition as we have used it on many applications to blast parts that required
special attention and to avoid the parts from "banging" together as they would in a
tumble blast or vibratory machine. The unit 480 VAC 3 phase with a control voltage
of 110 VAC. The rotary platform and vertical is a 24VDC variable speed drive motor.
The controller is an Allen Bradley for timed processes and vertical feed changes. A
dust collector unit is included. All guns (nozzles) are on individual arms that can be
articulated in many different positions for whatever application you may be doing.
Machine takes up a footprint of 8 foot by 6 foot and is 12 foot tall. Cabinets internal
blast are dimensions are 28'' wide by 42'' tall by 36'' deep. All door safety switches
and air solenoid equipment are in proper working order. Control cabinet is in safe
working order as well. It was once FAA approved to run jet turbines. Shipping
weight is approx. 1500-2500 lbs. Good condition. Asking $42,000 USD.
Item # M351 Surface Combustion Parts Washer. Suitable for use with a "Super
36" batch IQ furnace. Spray only. Electrically heated. Installed, in use and in good
condition. Asking $15,000 USD.
www.themonty.com
Item # M359 Spectra-Tech 0044-003 Infrared Microscope, Model WHK 10X
201, Reflected & Transmitted light, multiple objectives, Polaroid 4x5 attachment.
$6,500.00 USD.
Item # M346 SBS “QuenchAir”. SBS Corporation air/oil quench oil cooler. Single
fan unit model 5084-Q4. Serial number: 2365, 230/460 voltage, overall size:
74"wide X 104"long X 55"high. Comes with disconnects. Very good condition.
Asking $5,500.00 USD.
Item # M342 Pit Furnace Fixturing. Pit basket fixture. RA330 material. Fixture is
74” tall when put together. Baskets are 63” tall, each one is 20”deep. They have 2”
grid bottoms with mesh liners. These are of a hair pin design so that they can be
picked up when nested together. They can also be used individually. They are 54” in
diameter and have never been used. Asking $21,000.00 US dollars.
Item # M341 AFC Charge Car. Drawing # MT-237014. Voltage 480/3/60. Suited
for a 36” wide X 48” tray. External dimensions of 100” wide X 84” deep X 84” high.
www.themonty.com
Item # M348 Ipsen Automatic Dunk/Spray Washer. Model #WRD-11, Serial
Number 57690. Working dimensions of 36" wide X 48" deep X 24"+ high, 2200
pound capacity. Electrically heated, 72KW. Companion washer-In/Out or straight
through design. Door each end, Cal Rod element bundle. 12" wide belt oil skimmer,
air operated-full width elevator rack for submerged oscillation, overhead spray rinse.
Overall dimensions of 7' 5" wide X 5' 4" long X 11' 8" high. Rebuilt, excellent
condition asking $35,000 USD.
Side mounted control panel with Allen Bradley SLC 500 PLC Logic Control. Double
ended chain driven powered charge car with roller rail top. Excellent condition.
Asking $28,500.00 USD.
Item # M336 Cryogenic Unit. NU-BIT Cryomersion Model 1500, S/N 9911119.
This is a liquid nitrogen cryogenic unit used for treating material to -310 degrees
Fahrenheit. Working dimensions of 40” X 30” high X 30” wide. Maximum load 1500
pounds, normal load 800 pounds. 230 volts AC-20 amps., 3 phase, 60 HZ. Overall
dimensions 14’ long X 11’ wide X 13’ high. Manufactured in 1999. Good operating
condition with all manuals and drawings included. Asking $10,000 USD.
Item # M334 Berg Water Chiller. This is a BERG Air Cooled portable Chiller,
Model PA-1.5-1P capable of supplying 1.5 tons of cooling capacity at 15 degrees F
leaving and 95 degrees F ambient temperature. Used for only 3 days (low hours),
and is in nearly new condition. Electrics are 460/3/60 and it comes with a 575-460
transformer. Asking $7,500.00.
www.themonty.com
Item # M337 Endothermic Generator Retorts. RA-330 RX endothermic tubes,
four pieces, unused and in nearly new condition. Not sure what equipment these
came from, possibly an older Surface unit. Tubes measure 100" long, 11" OD, 10"
ID. Flanges on ends measure 14" x 15-1/2". Weight of each piece is approximately
480lb. Asking $2,350 USD each.
Item #M286 Cryogenic Unit. 2 chamber, each chamber 43" wide X 48" high, X
48" deep. Manufactured by MEI, Model #98-128. Capable of -310F to + 500F. 128
cubic foot capacity. Load capacity 10,000 pounds. Interior 10 gauge SS. Exterior 16
gauge SS (painted. Front Loading. Watlow-F4 Series controller. 2 circulating fans
and motors. Convection heating. Controls 120V, fan & heater 208 V. Pneumatic
100PSI. Control Panel side mounted. Front loading with two doors, swing from front.
Temperature range -310F to +500F (+-3F). Exteriors dimensions of 119" long X 90"
high (plus 24" for motors), depth 79" (plus 6 1/2" for electrical boxes. 700,000 BTU
gas heating has been added to unit. Massive industrial heavy grade
units. Completely rewired and painted. Like new condition but approximately half
the price of new. Asking $97,000 USD.
www.themonty.com
Item #M314 Holcroft Dunk/Spray Washer. Model GPWS 24-36-24. Electrically
heated, 480/3/60/50 amps. Working dimensions of 24" wide X 24" high X 36" deep.
External dimensions of 96"W X 143" high X 124" long (91" without skimmer
attached). This is a standard dunk/spray washer with 4 Warren Electric immersion
heaters. Spray nozzles are arranged over and all sides of the wash area. Load height
is 51" from floor to top of rollers. Wheel centres are 14-1/2". Controls are mounted
and wired on the right hand side of the washer and includes all necessary
pushbuttons and signal lights. There is a dunk cycle timer and spray cycle timer. A
Honeywell UDC 2000 digital temperature controller controls wash temperature.
Good condition. Asking $18,500.00 USD.
www.themonty.com
Item #M285 Cryogenic Units (3 Available). Manufactured by MEI, Model #98128. Capable of -310F to + 500F. 128 cubic foot capacity. Internal dimensions of
96" long X 48" deep X 48" high. Load capacity 10,000 pounds. Interior 10 gauge SS.
Exterior 16 gauge SS (painted. Front Loading. Watlow-F4 Series controller. 2
circulating fans and motors. Convection heating. Controls 120V, fan & heater 208 V.
Pneumatic 100PSI. Control Panel side mounted. Front loading with two doors, swing
from front. Temperature range -310F to +500F (+-3F). Exteriors dimensions of 119"
long X 90" high (plus 24" for motors), depth 79" (plus 6 1/2" for electrical boxes.
700,000 BTU gas heating has been added to each unit. Massive industrial heavy
grade units. Completely rewired and painted. Like new condition but approximately
half the price of new. Asking $97,000 USD Each.
Vacuum
See something you need, click on the link or scroll through all the items for sale. Searching
for something we don’t have listed, fill out our Contact Form.
•
•
•
•
•
•
•
20" Right Angle Poppet Valves
Abar Vacuum Furnace
AVS Vacuum
Debinding/Sintering Furnace
C.I. Hayes 6-Bar SemiContinuous Vacuum Furnace
Diffusion Pump "35"
Diffusion Pump "35"
Edwards Stokes 1722 Skid
Edwards Stokes 1722 Skid
GH Vacuum Induction Furnace
Ipsen Vacuum Aluminum
Brazing Furnace
•
•
•
•
•
•
•
•
•
•
•
•
•
Ipsen Vacuum Temper
Furnace
MD Blower
Kinney 75 CFM Vacuum Pump
Roots Gas Blower
Semi-Continuous Titanium
Diffusion Bonding Hot Press
Stokes 149H-11 80 CFM
Vacuum Pump
Sintering/De-Wax Furnace
Small Top Load Vacuum
Furnace
Surface Combustion Vacuum
Furnace
GCA-Vacuum Furnace
Vac Aero 2 Bar Vacuum
Furnace
Varian HS-20 Diffusion Pumps
(4 available
Vacuum Annealing Furnace
Item # VF294 Vacuum Annealing Furnace. Manufactured by Thermionics this is
a custom designed vacuum annealing furnace designed to heat treat wire up to 210
cm long. The vacuum chamber has an 8” Dia. X 90” effective working length. The
operating temperature was developed for a maximum operating temp of 1200° F,
The vacuum nominal level (continuous) duty was developed as 1 X 10-6 Torr.
Maximum vacuum level to operate in continuous duty is 5 X 10-8 Torr. The unit was
designed to use N2 gas. The unit was an R & D unit that was built in 1998, but has
had little to no use. Excellent condition. New this was $90,000 USD. Asking price
$29,000.00 USD.
www.themonty.com
•
•
•
Item #
Furnace,
x 10"H.
Pumped.
VF291 Small Top Load Vacuum Furnace. Brew Top Load Vacuum
Condition: Rebuilt by Pathways Thermal Technology. Work Zone: 10" Dia.
Max. Temp.: 2000F. Hot Zone: All Molybdenum. Vacuum: Diffusion
Power: 480V/3Ph/60Hz, 75 Amps. Price: $10,000
Item # VF289 Ipsen Vacuum Temper Furnace. Built in 1981. Working
dimensions of 280 mm high X 420 mm wide X 590 mm deep (11" X 16.5" X 23.2").
Maximum load 100kg (220 pounds). Minimum operating temperature 150C,
maximum operating temperature 700C. Input power 94 KVA, heating 71Kw, 575
volts, 60Hz. Type K T/C's, Honeywell controls. Vacuum contact point 1.0 X 10-1
www.themonty.com
Item # VF293 Abar Vacuum Furnace. Model HR50X48, S/N BM-817. Working
dimensions of 36” Wide x 48” Deep x 30” High Electric – 460/3/60 – 395 (Hot Load
Amps). Maximum operating temperature 2400° F. Horizontal Loading Moly Lined
Vacuum Furnace complete with Stokes 212 H Vacuum Pump (10 HP), United
Vacuum Booster Pump (7 1/2 HP), Varian Diffusion Pump (20” Diam), 315 KVA
Power Control Transformer, 50 HP Cooling Blower, “Big Joe” Type Loader, Single
Swing-Out Front Door and Spare Parts Include New 20” Diffusion Pump. NOTE: New
Hot Zone and New Super Systems Control System installed in 2008. Furnace last
run in October 2014. Free-Standing Control Panel complete with Super Systems
Digital Set Point Programmer, SSI High Limit, and Televac Vacuum Gauges. Very
good condition. Overall dimensions: 14’ Wide x 9’ Deep x 10’ High (Shipping
Dimensions). Approximate weight 20,000 pounds. Asking $155,000 USD.
mbar, operating pressure 1000 mbar. Maximum vacuum level 5.0 X 10-2 mbar.
Circulated nitrogen atmosphere gas. Elements Cr-Ni Steel. Stokes model 149H
vacuum pump. SS hot zone. Class 3 furnace with a temperature uniformity of +- 8C.
Used in an aerospace heat treat until it was shut down 2 months ago. Currently
being dismantled. Complete although missing the temperature recorder. Included
are a manual loader and 3 baskets. Excellent condition.
Item # VF285 20" Right Angle Poppet Valves (4 available). 20" Right Angle
Poppet Valves to mate to Varian HS-20 Diffusion Pumps. Removed from service in
good operational condition by a company converting to cryo pumps. Offered in AsIs or Standard Rebuilt As-Is Price: $ 1,800.00 (working, but no warranty, 30 Day
Return). Std. Rebuilt Price:
$ 3,150.00 (1 year warranty). Valves are
awaiting rebuild now. (2-3 weeks required ARO). Photo shows another
representative RAV prior to rebuild.
www.themonty.com
Item # VF286 Varian HS-20 Diffusion Pumps (4 available). Varian HS-20
Diffusion Pumps. Removed from service in good operational condition by a company
converting to cryo pumps. Offered in As-Is, Standard Rebuilt or Fully Rebuilt
conditions: As-Is Price: asking $ 4,750.00 (working, but no warranty, 30 Day
Return). Standard Rebuild Price: $ 7,500.00 (1 year warranty, re-use working
heating elements). Full Rebuild Price: $9,450.00 (1 year warranty, new heating
elements). Photos show another representative finished, rebuilt HS-20.
Item # VF281 Surface Combustion Vacuum Furnace. Model: IHVP-364830-2,
S/N: VC-42202-1. Work Zone Size: 42"W x 60"L x 30"H. Hot Zone: All graphite,
including hearth and elements. Vacuum System: Requires Stokes 1722 Skid (412H
mechanical pump and Stokes 615-1 vacuum blower. Both are missing), 16" Port for
diffusion pump, but no pump. Power Supply: 250 kW
460V/3Ph/60Hz. Max.
Temp.: 2400F. Max. Load: 3000 lb at 1900F. Cooling Gases: Nitrogen, Argon,
Helium. Gas Quench Capability: +12 PSI positive pressure. Cooling Fan: Top
mounted. Controls: Honeywell DCP-7700 Temp. Controller. Eclipse EMC-560 HiLimit. Honeywell Strip Chart Recorder. Philips Model 316 Vacuum Controller. Control
Thermocouple: Ni/Ni-Mo. Fair condition. Location: Southern California. Asking
$29,000 USD.
www.themonty.com
Item # VF282 AVS Vacuum Debinding/Sintering Furnace. This is a horizontal
graphite vacuum debinding sintering furnace for steel MIM parts completely rebuilt
from top to bottom by AVS in 2010. Working volume – approximately 18 cubic feet,
28” wide x 26” high x 42” long graphite retort, 1500# capacity. Temperature rated for continuous operation at 1400°C ±10°C in vacuum, 1450°C burn-out. 50µ
ultimate vacuum; leak rate <10µ / hour, CEDORT (Clean, Empty, Dry, Outgassed,
Room Temperature). De-bind system - nitrogen or argon sweep gas, 0 - 100 torr
differential pressure controlled by PLC and automatic I-to-P modulating vacuum
valve, binder trap, condenser assembly; options available for hydrogen gas and
burn-off. De-bind lines heated to keep vapor from condensing in vacuum lines. Fast
cooling with circulation fan and automatic gas re-circulation ports. Control system AVS ACE™ control/data acquisition system. Estimated cold-to-cold cycle time of 16
to 20 hours with AVS “Fast Cool” option. Horizontal jacketed chamber - 60" dia. x
80" long, nominal dimensions, flanged, on legs. SA-516-70 mild steel construction
on water jackets and door + body flanges. Stainless Steel inner jacket & dished
head plus all power ports Front-loading chamber with 2 doors - both doors on
adjustable hinges, with buna o-rings, manual clamps, for operation from 50 millitorr
vacuum to 3 psig positive pressure; rear door opens for service. Ports - rough line
on side of chamber, delube line from bottom, fan housing flange on rear door
Additional PORTS added to the system to accommodate future system modifications
for processing ‘sinter-hard’ P/M materials – a total of up to 7 additional ports
ranging from 18” in diameter down to 1” in diameter will be added. Further details
available upon request. Currently installed and in excellent condition. Asking
$209,000 USD.
Item #VF275 Ipsen Vacuum Aluminum Brazing Furnace, Model: VC36X48X36(14)RS, Ser. No.: 59213. New Approx. 1984. Work Zone: 36"W x 48"D x
36"H. Electric Heat, 225 kW, Power: 460V/3Ph/60Hz Zones of Control: 10. Hot
Zone: Alloy Lined Interior and Alloy Hearth and Elements. Vacuum System:
Mechanical Pumps: Stokes 412 Mechanical with Stokes 615 Blower, Diffusion
Pump: Varian "30 inch" (probably 32"). Holding Pump: Welch Power Supply:
Water-cooled VRT Transformers. Water Cooling System: Included - with cooling
tower and expansion/storage tank. Spare Parts: 2 crates of new, spare heating
elements. (probably Ni-Chrome). Controls: Panel with programmable Honeywell
and LFE digital controllers. Includes: Disconnecting and Loading are included in this
price. Condition: Excellent. This furnace was only used to run test samples over its
use "career" and is in excellent shape. Demonstration: In service and operational at
this time. Asking Price: $215,000 USD
www.themonty.com
Item # VF 280 Vac Aero 2 Bar Vacuum Furnace. 1998 Vac Aero Model VAH
1220 HV-2, 2400ºF Max. Temp., 2-Bar Gas Quench, Work Zone: 8"W x 9"H x
20"D. Hydrogen or inert gas partial pressure capability. Has had only very light
use. Set up for hydrogen (partial Pressure only) , argon or nitrogen gases. Vacuum
System: Edwards E2M80 Roughing Mechanical Pump, Varian VHS6 6" Diffusion
Pump, and Varian DS102 Holding Pump. Gas Cooling: Vac Aero 10HP Turbine, 600
CFM, 2-Bar maximum quench pressure. Max. Burn-out Temperature is 2450ºF.
Uniformity per AMS 2750C. Max. Load: 60 lb. @ 2400ºF. Power Input for Heating:
35 KVA Hunterdon V.R.T. Hot Zone Insulation: Graphite Felt with Graphite Foil
Face. Heating Elements: Molybdenum. Controls: Honeywell DCP-551, UDC 3300
Overtemp (Type S/C). Edwards Model AGC Vacuum Gauges (T/C and Cold
Cathode.
Honeywell DPR-250 Chart Recorder. Footprints:
Furnace Control
Cabinet 30"W x 30"D x 84"H. Vacuum System: 75"W x 126"L x 95"HTransformers
(2 Ea.): 25"W x 25"D x 25"H. Controls and Vacuum Equipment skid mounted.
Transformers currently on wall above furnace. Excellent condition. Asking $89,500
USD.
Item #VF267 SEMI-CONTINUOUS Titanium Diffusion Bonding Hot Press.
System consists of; Load Chamber. Rated for 2720 kg load Moly Pin walking
system rated for 2720 kg load 44” w x 54” d x 6.5” high product size in semi
continuous mode Stokes 612/300 pump/blower Mounted on roll out frame for easy
maintenance
Preheat Chamber. 35” diffusion pump / 100 CFM holding pump Moly Pin walking
system rated for 2720 kg load 44” w x 54” d x 6.5” high product size in semi
continuous mode Stokes 300 CFM mechanical pump 5 x 10-5 Torr in 20 minutes 300
kW heater power (Hunterdon) Moly Hot Zone Mounted on roll out frame
Bonding Chamber. 20” diffusion pump / 100 CFM holding pump Moly Pin walking
system rated for 2720 kg load 44” w x 54” d x 20” high product size in batch mode
44” w x 54” d x 6.5” high product size in semi continuous mode Constant 1100°C
Heated Platens, Moly pressing surface 1000 tons of force, up pressing ram 300 kW
heater power (Hunterdon) Moly Hot Zone Mounted on roll out frame
Cooling Chamber. 20” diffusion pump. Stokes 612/300 pump/blower Moly Pin
walking system rated for 2720 kg load 44” w x 54” d x 6.5” high product size in
semi continuous mode Fast Cool 60°F /min argon. 1750F to 1200F. 25°F variation
over part 5 x 10-5 Torr in 20 minutes Fast Backfill Port Mounted on roll out frame
www.themonty.com
Item #VF271 SINTERING/DE-WAX FURNACE. Horizontal sintering furnace with
wax condenser 1470°C operating temperature. Water cooled 304 stainless steel
chamber with mild steel flanges. Graphite hot zone - 24” wide x 18” high x 36”
deep, with hearth rails. Graphite retort - 4 to 5 cubic foot work space, shelves,
graphite rollers, de-wax tube and -cooling. 5 HP recirculation cooling fan system cooling flaps in insulation and retort. Wax condenser assembly with hot water
circulation system and removable wax receiver pot. Power supply - transformertype, low voltage secondary, nominal 250 kW. Vacuum pumps - Stokes 212-H, 150
cfm rough pump, Roots 615, 1600 cfm booster. Dynamic partial pressure gas
system. Unit can be seen in operation and is available for immediate delivery.
Asking $299,000 USD.
Item #VF266 Kinney 75 CFM Vacuum Pump: Warranty Rebuilt Kinney Model
KTC-75, Part No. 804982-D, S/N 1105-Y 7710-5 mechanical vacuum pump. 12
Month warranty on rebuild. Will be repainted at rebuilder's shop. Running without
problems when removed from service. Price: $ 5,700
F.O.B. West Coast U.S.
Item #VF265 Stokes 149H-11 80 CFM Vacuum Pump: Rebuilt Stokes Model
149H-11, Lot# CD-81004 Mechanical Vacuum Pump, Rebuilt by Evey Vacuum in
2002 and stored in heated, dry area since then. Asking Price; $ 5,500.00 USD
with 30 Day Right of Return if not satisfied.
Item #VF263 Edwards Stokes 1722 Skid: Warranty rebuilt Stokes 1722 Skid.
Stokes Model 900-412-014 Mechanical Pump (Newer Style). S/N: 069035063
Date: 2006-12. Motor: 10 H.P. Stokes 615-1 Blower. S/N: 865850X0696
Lot:
79894-15. Motor: 7.5 H.P. Skid Mounted. Interconnecting Pipe and Fittings. Stokes
Demister. Allow 2-3 Weeks ARO for Rebuild of pumps. Asking Price: $ 22,500.00
USD in rebuilt condition with Rebuilder's 12 Month Warranty. May be purchased As-
www.themonty.com
This system is ideal for any company wanting to develop process for diffusion
bonding of any materials which are capable of being processed within the
specifications of the furnace. The system is available as a batch or semi-continuous,
as the system can be set up in Batch mode for development purposes and semi
continuous mode for production. The system is available for inspection as
warehoused in the Northeastern USA. New Price for this system is over USD
$16,000,000. This system is available in almost any configuration. As is
$890,000.00 cash and carry with support available from the original manufacturer
at a reduced rate, or reconfigured to match your specific requirement at a price
TBD. Immediate delivery.
Is if done prior to the rebuild. Location: U.S. West Coast. Photo shown is before
rebuild. Will be repainted after rebuild.
Item #VF260 C.I. Hayes 6-Bar Semi-Continuous Vacuum Furnace: 1998 C.I.
Hayes Model CVPQ-202436, 6-Bar Pressure Quench Semi-Continuous Vacuum
Furnace, (75 PSIG vessel rating). Work Zone: 24"W x 36"L x 20"H, with Graphite
Insulation and elements 460V/3Ph/60Hz, 125 kW, 2400˚F max. Temp. rating.
Designed for 250 lb/hr Throughput. 300 CFM Mechanical Vacuum Pump, Water
Cooling Requirement: 113 GPM (130 GPM max. at 95˚F-105˚F, 15 PSI). Overall
Space Requirement: 13 ft Wide x 51 ft Long. Allen-Bradley SLC-500 PLC, Honeywell
DCP-551 Temperature Controller, Upgraded with addition of Super System, Inc.
Model 9010 Programmable. Controller for recipes. Data communications capability.
Excellent Condition, Hot zone new 2 years ago and has had very light use since.
Operational, but only for another week or two. Owner is removing it soon to make
room for new furnace equipment. Asking price: $230,000 USD for quick sale.
Item # VF256 GCA-Vacuum Industries Vacuum Furnace. Model Series 3700242436. S/N 41293 LV. Working dimensions of 24" wide X 36" deep X 24" high.
460/3/60-207KW. Maximum temperature 2400F. Horizontal loading vacuum furnace
www.themonty.com
Item #VF262 Edwards Stokes 1722 Skid: Warranty rebuilt Stokes 1722 Skid.
Stokes
Model
900-412-014
Mechanical
Pump
(Newer
Style).
S/N:
069034482, Date: 2006-11. Motor: 10 H.P. Stokes 615-1 Blower. S/N:
813770X0898
Lot: 78315-38. Motor: 7.5 H.P. Skid Mounted. Interconnecting
Pipe and Fittings. Stokes Demister. Allow 2-3 Weeks ARO for Rebuild of pumps.
Price: $ 22,500 USD in rebuilt condition with Rebuilder's 12 Month Warranty. May
be purchased As-Is if done prior to the rebuild. Location: U.S. West Coast. Photo
shown is before rebuild. Will be repainted after rebuild.
complete with graphite lining, graphite heating elements, Stokes 212H vacuum
pump, Roots booster pump, rear mounted cooling fan, heat exchanger (6 months
old) and 200 KVA transformer. Also included is a new spare hot zone (still in crate).
Free standing control panel complete with BC 570 set point programmable
temperature controller, BC Series 10 High Limit controller and Teledyne vacuum
gauge. Overall dimensions 95" wide X 12' deep X 96" high (shipping dimensions).
Approximate weight 12,000 pounds. Very good condition. Asking $119,000 USD.
Item # VF254 MD Blower, 350 CFM: Rebuilt (per owner) M.D. Pneumatics 350
CFM gas blower, Model 11-3210, S/N 1735R A23, on skid but needs motor.
Location: Pacific North-western U.S. Asking Price: $3,000.00 USD. 30 Day Right
of Return, if unhappy.
Item # VF253 Vacuum Induction Furnaces (2 available). Built by GH
Induction Atmospheres in 2008. Model VF-40. Working dimensions of 12" diameter
X 17" high. Overall dimensions of 86" wide X 86" long X 96" high. S/N 018/VF40/173. 2100F. 400-480 Volts, 200 amps., 3 phase, 50/60 HZ. Honeywell UDC
Digital temperature control, hi-limit control and strip chart recorder along with GE
Fanuc Quick panel and Televac vacuum gauge. SS vessel mounted vertically above
load platform. Interior of vessel has induction coil, 15" diameter. Ceramic sleeve and
14" diameter graphite susceptor. Parts to be heated are loaded on the work platform
and raised (hydraulically) into hot zone which is heated by a 100KW, 50 Khz power
supply. Vacuum pump is a Pfeiffer Model DUO35 21 CFM (36 cubic metres/hour). At
www.themonty.com
Item # VF255 Roots Gas Blower: Rebuilt (per owner), Roots Model 2510J
Whispair Max gas blower, 372 CFM, Roots I.D. 847-485-20, S/N 76 54846 with 5
H.P. Motor mounted on skid. Location: Pacific North-western U.S. Asking
Price:$3,500.00 USD. 30 Day Right of Return, if unhappy.
completion of heat cycle furnace is back filled with Argon and cooled by external
blower and heat exchanger. Water chiller is available and will be quoted upon
request. Excellent condition. Asking $125,000 USD each.
Item #VF242 " 35" Diffusion Pump: CVC Model PMC-32C, 35" Diffusion Pumps
(Today this is the Varian HS-35. Varian purchased CVC rights to this pump.) Can
be purchased either in As-Is condition or in Rebuilt condition with a warranty. 35"
Throat Diameter. Bolt Circle is approx. 38-3/4" with 14 Holes on approx. 8-9/16"
Centers. Flange O.D. is 41-3/4". O-Ring Center Diameter is 36-1/8". Approx. 723/4" Overall Height (79" on 48" x 48" shipping pallet). Note: Mating 35" CryoBaffle is also available for improved low-range vacuum and elimination of
backstreaming (See Item# 3161 Below). 6" Foreline with approx. 9-1/2" Bolt Circle
with 8 Holes on approx. 3-5/8" Centers. 1/4" dia. O-ring is approx. 8-7/8" diameter
to center. Shipping Wt. with pallet approx. 2050 lb. Price in As-Is Condition: $
6,400.00 USD Price in Warranty Rebuilt Condition, Painted: $ 12,250.00 (with
existing working elements. Add $4,500 if you want brand new elements.)
www.themonty.com
Item #VF243 35" Diffusion Pump: CVC Model PMC-32C, 35" Diffusion Pumps
(Today this is the Varian HS-35. Varian purchased CVC rights to this pump.)
Rebuilt condition with a 12 Month warranty. 35" Throat Diameter. Bolt Circle is
approx. 38-3/4" with 14 Holes on approx. 8-9/16" Centers. Flange O.D. is 413/4". O-Ring Center Diameter is 36-1/8". Approx. 72-3/4" Overall Height (79" on
48" x 48" shipping pallet). Note: Mating 35" Cryo-Baffle is also available for
improved low-range vacuum and elimination of backstreaming (See Item# 3161
Below). 6" Foreline with approx. 9-1/2" Bolt Circle with 8 Holes on approx. 3-5/8"
Centers. 1/4" dia. O-ring is approx. 8-7/8" diameter to center. Shipping Wt. with
pallet approx. 2050 lb. Price in Warranty Rebuilt Condition, Painted: $ 12,250.00
(with existing working elements. Add $6,000 if you want brand new elements.)
Location: Coeur d'Alene, Idaho 83814
www.themonty.com
Employment Opportunities
•
Senior Metallurgical Engineer
Quality Manager
Experienced Regional Sales
Manager
Sales Engineer
•
•
•
Quality Control Manager
Wanted
Metals Processing Commercial
Technology Engineer
Manufacturer’s Sales
Representatives
Item #0288
Senior Metallurgical Engineer Wanted. “ALD Thermal
Treatment, Inc., Port Huron, MI, the leader in LPC/HPQ to the automotive industry,
seeks both a senior level Metallurgical Engineer as well as a more recent graduate
to support our R & D activities. Applicants should send Resume/CV and cover letter
to HR@ALDTT.net “
Primary Duties of Position:
•
•
•
•
•
•
•
•
Responsible for the design of metallurgical processes and product
engineering.
Analyze product failure data and laboratory test results to determine causes
of problems and develop solutions.
Perform root cause analysis of failures.
Manage Metallurgical Laboratory and all Quality Control functions.
Provide technical support of heat treat process and to the metallurgical lab on
daily basis.
Assist in the design and development of heat treat parameters for new
products and processes including continual improvement of existing
methodologies.
Perform required metallurgical testing analysis, evaluates mounted samples
and analysis of microstructures.
Research metallurgical properties of current and proposed materials.
www.themonty.com
•
•
•
•
•
•
•
•
•
•
Necessary Knowledge, Skills and Abilities:
•
•
•
•
•
•
•
•
•
•
•
•
Project Management and group presentation skills and experience.
Computer proficiency including Microsoft Office Suite. Previous experience
working within Quality Software and ERP systems.
Excellent problem solving and trouble shooting skills.
Lean manufacturing concepts.
The ability to multi-task handling multiple projects simultaneously without
sacrificing quality of work.
The ability to independently do deep dives on technical issues and to present
findings clearly to customers in difficult situations.
Excellent written and verbal communication skills with the ability to clearly
communicate complex technical information to diverse audiences.
The ability to effectively interact with all members of the organization and
work well with cross-functional teams.
Strong attention to detail.
The ability to work independently with little to no supervision.
Must be able to read and understand documents written in English, and be
able to speak and write in English as it pertains to the position.
A strong understanding of automotive quality requirements including but not
limited to TS 16949, QS 9000 and AS 9100.
Travel: Occasional travel to customer sites, to ALD Ramos, MX and to ALD in
Europe.
Required Education: Bachelor degree in Materials Engineering or equivalent
required. Master degree in Metallurgy preferred.
Experience: 5 years experience as Metallurgist. Previous heat treating experience in
case hardening, LPC and/or gas nitriding preferably in Automotive.
Item #0287 Quality Manager Wanted. Solar Atmospheres of California is looking
to hire a site Quality Manager. The ideal candidate would have a minimum 5 years’
www.themonty.com
•
•
Conduct metallurgical failure test analysis and propose
corrective/preventative actions.
Read and interpret engineering drawings and technical specifications.
Develop process simulations and heat treat/carburization models.
Develop recipes for implementation in heat treat furnaces.
Program recipes in heat treat furnaces.
Perform test cycles and apply appropriate requirements to meet customer
specifications for heat treat protocols as well as capability and risk
assessments.
Assists in Contract Review, APQP, PPAP process and changes, etc.
Communicates with customers as necessary in regards to all research and
development projects as well as customer complaints and requests including
technical requirements.
Responsible for ensuring all deviant or suspect products is identified and
quarantined.
Interested? Please contact: Mike Moffit VP of Operations mikem@solaratm-ca.com
Item #0286 Al-Fe Heat Treating, a multi-state heat treating company based in
Fort Wayne, Indiana, is searching for an experienced Regional Sales Manager to
cover a five state territory which includes Indiana, Illinois, Michigan, Wisconsin, and
Kentucky.
Responsibilities include but are not limited to:
•
•
•
•
•
•
Management and oversight of all pricing / prospecting information for their
assigned region
Maintain contact and relations with all existing customers
Obtain new customers
Develop regional and divisional sales forecasts on a periodic basis
Manage the quoting process for all prospect & customer quotes for their
assigned region
Assist the Director of Sales and Marketing with marketing plan and activities
Qualified applicants MUST possess the following:
•
Bachelor’s degree in business management, sales or marketing
www.themonty.com
experience in Quality Assurance and Heat Treatment. Proficient in reviewing and
comprehending regulations, guidelines and standards of Quality Assurance and
materials processing. AS9100/ISO9001 and Nadcap experience are highly desirable.
This position may require some travel. The following are some of the responsibilities
of the position:
· Ensures the Quality system is in conformance with the corporate quality system
· Maintaining the pyrometry and calibration systems
· Responsible for preparation and hosting registration and customer-conducted
audits
· Manages the customer compliant resolution and nonconformance report activities
on site
· Makes adjustments to the on-site quality system to meet regional market demands
for the site after the review of executive management
· Responds to quality and technical requests
· Communicates regularly with site Managment
· Responsible for ensuring that the state of the Quality System is reported to
management and other pertinent personnel
Requirements:
· Knowledge of Quality System ISO9001-bases standards, AS9100, and NADCAP
requirements for heat treating and brazing
· An understanding of metallurgy
· Must work efficiently with little to no supervision
· Must work well with other employees and management
· Must be detail oriented
· Must possess basic computer skills
· Must be able to travel
•
•
•
•
•
Minimum of five years of outside sales experience
Neat, clean, professional appearance
Ability to communicate effectively, both orally and in writing
Above average organizational skills
Willingness to travel, including overnight travel
Item #0285 Sales Engineer Wanted. Due to continued growth, Paulo is looking
for a Sales Engineer in the Nashville, TN area. If you’re interested in working for
an industry leader that provides employment which is satisfying and gives you a
sense of accomplishment and pride, then this is the job for you. With a company
this size, you will enjoy exposure to a range of industries including automotive,
medical, military, aerospace, and agricultural to name a few. In this role, you will
get to learn more about these industries as you meet with Customers to see how
their products and materials are made and determine what Paulo can do to help
them succeed. No two days will be the same. Each day will offer up something new,
interesting and challenging. As the Sales Engineer, you will sell Paulo’s service, not
products. That means that your focus will be on the Customer and how you can help
them save money and improve their products. Gain satisfaction from helping people,
and avoid a sales career that focuses only on the number of products sold. You will
be in the business of providing superior service to new and existing Customers. If
you are a self-starter who enjoys working in a fast paced environment, join the
Paulo team now.
Some of the benefits to you:
· Competitive compensation
· An excellent benefits package including medical, dental, 401k, pension
· Company paid vacation and holidays.
· Potential opportunity for advancement, especially for those with strong work ethic,
flexibility, and willing to relocate
The ideal candidate will have a degree in business or sales and marketing, and
experience in industrial, manufacturing, or technical sales. Take advantage of this
opportunity to turn up the heat on your sales career. Join the Paulo team today.
About the company: Paulo delivers innovative engineered heat treating, brazing,
and metal finishing solutions that provide superior metallurgical results. Paulo
remains a leader in the heat treating industry by developing new technologies and
refining our processes to meet our Customer's needs. Visit us at www.paulo.com
Employment No phone calls please.
Item #0284 Quality Control Manager Wanted for a Heat Treating facility.
Seeking Quality Manager. An established Heat Treating Company is looking for a full
www.themonty.com
This position does not have responsibility for any direct reports. Al-Fe Heat Treating
offers a competitive salary (non-commission position); medical insurance with a
health savings account with employer match; dental, vision, short-term disability,
and life insurance; 401(k) with employer match; education assistance and more.
time Quality Manager. This position is based in the northeast. Applicant will
coordinate the Quality Management System and Continuous Improvement initiatives
to meet customer expectations. Major customers include aerospace, military,
nuclear, automotive and agriculture. Compensations will be commensurate with
experience. Full time position.
Job Requirements:
Bachelor's degree in a technical field or a minimum of 3 years experience in quality
management.
Heat treat experience preferred.
Must be organized and motivated.
Plan, prioritize and organize work with appropriate timeliness.
Must be a Team player and communicate well with others.
Manage Metallurgical Lab.
Must have strong verbal, written communication and interpersonal skills. Calm
under pressure.
Proficient in Microsoft Office software including Excel, Power Point and Word
Qualified applicants are encouraged to send resume to heattreatquality@yahoo.com
Item #0283
CAREER OPPORTUNITY - METALS
PROCESSING COMMERCIAL TECHNOLOGY ENGINEER: Air Products is a
manufacturer of Industrial gases and chemicals. This position can be based in
California, Washington or Arizona. This individual will play a role in the growth of our
business, focusing primarily on applications for gas atmospheres in metals heat
treating, such as autoclaves and is focused on providing value-added solutions
requiring industrial gases (nitrogen, hydrogen, argon, helium, and oxygen) with an
emphasis on the aerospace segment. To apply for this position, please visit the Air
Products Career Center at www.airproducts.com/careers. You can apply specifically
to Job Req #17994BR.
www.themonty.com
Responsibilities:
Maintain Quality system that meets customer Quality requirements.
Maintain Quality manual and related procedures per Nadcap standards.
Host/participate in audits performed by Customers.
Host/participate in audits performed by PRI/Nadcap registrar.
Maintain a Pyrometry system as required in AMS 2750D.
Coordinate and conduct quarterly management Review Meetings.
Manage a calibration recall system for periodic testing including Pyrometry and
Hardness testing equipment.
Perform external and internal audits.
Write and review Heat Treat procedures from customer drawings, procedures and
quotations.
Ensure timely responses to corrective action requests to customers.
Support the Production Department with quality issues.
Other Skills/Abilities: Language Skills – Ability to read and comprehend
instructions, multiple correspondences and memos. Ability to write correspondence
and effectively present information in one-on-one and small group situations.
Second language is a plus. Reasoning Skills – Ability to apply common sense
(understanding) to carry out instructions furnished in written, oral and diagram
form. Ability to prioritize and solve multiple issues/tasks concurrently. Send line card
and resume to: Mark Heninger, Ipsen, 984 Ipsen Road, Cherry Valley, IL 61016. Or
email: Mark.Heninger@IpsenUSA.com
www.themonty.com
Item # 0281 Manufacturer’s Sales Representatives Wanted. Ipsen, a leading
furnace manufacturer with locations worldwide, is currently looking for skilled,
motivated Manufacturer’s Sales Representatives or Agencies to serve areas
within Canada; Latin America (emphasis in Mexico); and the Northwest and
Southwest U.S. Ipsen services multiple industries, including Automotive, Aerospace,
Energy, Commercial Heat Treating and Tool & Die. Our Representatives are
responsible for building and maintaining relationships with our customers, as well as
positively representing our brand in all interactions and settings. Customer service is
a priority. Reps must reside within the sales region. Qualified candidates must be
familiar with thermal processing equipment, as well as possess a minimum of five
years of experience in capital equipment sales and be proficient in CRM. Extensive
travel is also a must for this position. An advanced technical degree or a
combination of education and experience will be considered.
Seeking Employment
See something you need, click on the link or scroll through all the items for sale. Searching
for something we don’t have listed, fill out our Contact Form.
Experienced Brazing
Individual
Item # E128 Experienced Brazing Individual is looking for a position as either
a General Manager/Production Manager/Operations Manager/Sales. Over 20 yrs
experience in all aspects of an exothermic and bulk gas (hydrogen/nitrogen)
continuous belt brazing facility. Responsible for day to day operations with hands on
involvement. Forecasting, budgeting, scheduling all included in previous duties.
Customer relations as well as supplier coordination included. Troubleshooting issues
with equipment and resolving braze issues included. P&L mgmt essential to
responsibilities. Direct reporting to regional operations manager. Supervised and led
over 100 employees on 3 shift operation that supplied directly to OEM. Brazed
product that included torque converters, fuel rails, brake hose ends, fluid transfer
tubes, pressure canisters, etc. Key characteristics entail being driven for success,
hard working, integrity, learn new processes, and able to adapt to any environment.
Currently reside in Coldwater Michigan. Upon right opportunity would be willing to
relocate. I can be reached at: ttell@outlook.com or by phone at 5176171705
www.themonty.com
•
In Parting,
We always enjoy comments, feedback and constructive criticism. Thanks for your
feedback and don’t hesitate to let us know your thoughts. Don’t forget to visit us
daily at www.themonty.com.
Email: gord@themonty.com
www.themonty.com
Gord Montgomery,
W.G. Montgomery Limited
Phone: 905 271-0033 Fax: 905 271-9324