Installation/Assembly Instructions
AeroLift 35 Video Conferencing Camera Closure, Environmental Air Space Housing & Ceiling Trim Kit by Draper
Installing Optional Environmental Air Space Housing
The Environmental Air Space Housing is shipped pre-assembled in its shortest position. The height of the housing can be adjusted by moving the screws
to different mounting holes in side panels. The incremental adjustment for the
top screw and bottom screw is ½"; the incremental adjustment for the rest
of the screws is 1". You can install the housing in a pre-assembled state or
as separate components, which will require that the housing be completely
disassembled prior to installation.
Please note that if the Environmental Air Space Housing is to be installed in a
space where there is no access from above the housing, then it is recommended that the AeroLift 35 be installed to the upper section prior to installing
the housing. It is also recommended that an access panel be installed to allow
future access.
Refer to Figure 1 for these instructions.
1 Install top section of housing using outer four holes located on top of
upper section. If installing large housing, make sure it is oriented properly
to allow correct placement of lift within housing.
2 Attach AeroLift 35 to upper section of housing through the inner four
holes in the upper section with the 5/16" –18 x 7/8" hex head screws, 5/16" flat
washers and lock nuts provided with housing. The lock nuts should be
used above the housing (one per screw).
3 Attach A & B (the two flat panels of the middle section across from each other) with the clinch nuts to the outside of the housing.
4 Attach C & D (the two middle section panels with the formed ends) across
from one another.
5 Attach E & F (the two larger lower section panels across from each other
with the clinch nuts to the outside of the housing. E to C and F to D.
6 Attach G & H (the two remaining lower section panels) across
from one another.
7 Attach ceiling trim kit to lower section of Environmental Air Space Housing.
Caution: Make sure bolts and nuts are completely tightened.
Small Environmental Air Space Housing, and Camera Closure Dimensions
Top View
Exploded Environmental Air Space Housing
Figure
Upper Section
Middle Section - A, B, C, D
Lower Section - E, F, G, H
Ceiling Trim Ring 23 7/8"
EASH Mounting
Holes 8¾"
Ceiling Trim Ring 14 9/16"
EASH Mounting Holes 21¼"
Lift
Mounting
Holes
Ceiling Trim Kit
Closure
Panel
15 5/8"
10 1/8”
Ø 7/16" 4x
19 3/8"
Closure Panel 25"
Lipless Closure Dims: 22 1/8" x 12 1/8"
EASH 23 ½"
EASH 14 ¼"
Side View
Front/Back View
Ceiling Trim Ring 23 7/8"
EASH 23 ½"
EASH
Ceiling Trim Ring
14 9/16"
EASH14 ¼"
EASH
Assembled Environmental Air Space Housing
Figure
Upper Section
20 /16”
3
Trim Ring 16 9/16”
EASH
12¼”
7
/16”
1511”
10”
2 /16”
13
12 5/8"
to
20 5/8"
TRIM RING
Center of Rod
21"
93/8”
to
143/8”
19/16”
Between Rod
20 / "
Space Between
11
16
9¾”
22 5 "
Closure
14 / ” Panel 25"
1”
Trim
Ring
6¾”
to
Closure
11¾”
Panel
Trim Ring 13 9/16”
EASH
12 / ”
7
16
TRIM RING
/16”
11
Center
of Rod
101/8”
Between
Rod
7½” 9
9 /16”
/8
CLOSURE PANEL
13 3/16"
9
11 / ” Panel
Closure
16
Closure Panel 167/8”
9
16
15 5/8"
Closure Panel 13 / ”
7
Middle Section
Lower Section
8
Ceiling Trim Kit
Copyright © 2016 Draper Inc.
Form AeroLift35_VCCameraClosure_Inst16
Printed in U.S.A.
If you encounter any difficulties installing your AeroLift 35 Environmental
Air Space Housing, Closure or Ceiling Trim Kit, call your dealer or Draper,
Inc. in Spiceland, Indiana, 765-987-7999 or fax 765-987-7142.
AeroLift 35 - Video Conferencing Camera Closure, Environmental Air Space Housing & Ceiling Trim Kit by Draper
Assembling Camera Closure
7 Attach trim ring (1) to closure panel using 10-16 x ½" Truss Head screws.
If your AeroLift 35 is equipped with a ceiling closure system, it can be used as is, or in
conjunction with a piece of existing ceiling tile.
Please refer to diagrams below for these instructions.
1 If installing with ceiling tile, you may need to cut tile so overall dimensions are the
same as (or slightly less than) the closure panel. Place tile into trim frame. Lay
closure panel on top (back side) of ceiling tile, and tighten screws to hold in place.
2 Determine the desired height of camera shelf opening (range: 6¾" to 11¾").
3 Assemble left and right panel brackets using ½"-20 x 5/8" screw and nylon hex nut.
4 Attach panel brackets to slots in projector plate using ¼"-20 x ¾" screws, washers
and locking nuts.
Caution: Make sure nuts are completely tightened.
8 Test unit operation to confirm that panel will stop in closed position just before
touching ceiling.
Caution: DO NOT hang from, "ride" or pull down on the unit. This
could create a failure and cause damage and/or injury.
PLEASE NOTE: Immediately upon completion of the surrounding ceiling, unit
should be operated to confirm that optional ceiling closure panel by Draper or
by others stops 1/8" short of touching ceiling in closed position. If closure panel
touches, the motor may continue operating after the lift is closed. If it continues
to cycle once the lift is closed, a failure may occur, making the unit descend
rapidly and causing damage and/or injury.
Caution: Make sure bolts and nuts attaching brackets to AeroLift are
completely tightened.
5 Attach Closure Panel (11) using ¼"-20 x 5/8" Hex Head screws, washer and locking nut.
6 Place Camera Shelf (3), on top of the closure panel between two lower sections of
panel brackets and attach with 10-32 x ½" screw (4) and #10 Helical
Spring Lock (5).
14
16
Assembled Camera Closure Dimensions
12¼”
7
11”
10”
6
3
12
10
Camera Shel
f
9¾”
15
10
93/8”
to
143/8”
13
9
4
19/16”
5
9
149/16”
8
Closure Pane
10”
5½”
11
l
167/8”
Trim Ring
2¼”
1
2
/16”
11
1
Item Qty Part Number
Description
11C028.689.08SA
Frame, VC Trim Ring
28 C020.558
Screw, 10-16 x ½" 6 Lobe Truss Head AB E
31C044.218.08SA
Panel, VC Shelf
4
4
C020.389
Screw, 10-32 x ½" PPH Zinc Machine
5
4
C013.019
Washer #10 Helical Spring Lock
6
4
C020.153
Screw, ¼"-20x¾" Grade 2 Zinc Split Lock
74 C013.028Washer ¼" ID x .365OD x .063T Zinc Split Lock
84 C020.152 Screw, ¼"-20 x 5/8" Hex Head Grade 2 Zinc Cap
98 C013.033
Washer, ¼" Wide 5/16" ID x 47/64" OD 1/16" Thk Zinc Flat
108 C018.014
Nut, ¼"-20 Nylon Inserted Hex Zinc Locking
111C044.217.08SA
Panel, VC Closure
124 C020.188
Screw, ¼"-20 x 5/8" Phillips Pan Head White Machine
131C044.221.08SA
Panel Backet, VC Lower Left Side
141C044.222.08SA
Panel Bracket, VC Upper Left Side
151C044.223.08SA
Panel Bracket, VC Lower Right Side
161C044.224.08SA
Panel Bracket, VC Upper Right Side
6¾”
to
11¾”
7½”
119/16”
137/8”
www.draperinc.com
(765) 987-7999