Complete Installation Guide
Ethernet Media Converter
Model Number: OT-PLC601
Product Description
Product Features
OT-PLC601 is a high-speed Ethernet transmission
◆ Long distance transmission up to 2,000m over RG59.
device. It supports both a point-to-point and point to
◆ Duplex network, maximum physical bandwidth up to
multi-point. It is used to transmit data network signal over
240Mbps.
any pair of two-wire such as CAT5, coaxial cable, power
◆ Transmit high-speed data network signal over any pair of
line, etc. The maximum distance is up to 2000 meters.
two-wire.
The largest physical bandwidth is up to 240Mbps.
◆ Support the power with cable transmission using EOC
technology.
Additionally, this product can support the power with
◆ Simple device configuration, transparent transmission, no
cable transmission (need an external power adapter for
need adjustment.
220VAC power supply). So you can use the existing
◆
power line to transmit data network signal. This product
correction coding technology.
can be widely used for network extension system,
◆ Easy installation, plug and play, fast Ethernet connection.
Low
network security system, network information publishing
system, network renovation and expansion systems,
railway, urban traffic, mining and telecommunication, etc.
Page 1 of 6
power consumption,
high performance error
Complete Installation Guide
Connection Diagram
Application Ⅰ:
Application Ⅱ:
Terminal Instructions
Page 2 of 6
Complete Installation Guide
Installation Instructions
1.Connect the remote Ethernet Media Converter LAN port
4. Connect the low-voltage power supply (DC12V) to the port
to the network equipment RJ45 output. COAX
CABLE port
of local side, POWER indicator
LAN indicator
is connected to two-wire by BNC
lights,
lights, then the COAXIAL indicators
of both remote and local sides lights.
connector.
2.Connect the low-voltage power supply (DC12V) to the port
of remote side, POWER indicator
lights,
5.SLAVE/MASTER switch
is used to set remote/local
device. On one network signal transmission line, there is only
LAN indicator
lights.
one local device. Its switch should be set in MASTER side.
MASTER indicator
3.Connect the other end of the two-wire cable to the local
Ethernet Media Converter BNC port
,
will be on. All other remote devices
should be set in SLAVE side, and MASTER indicators will be
on in power-on moment, then be off.
LAN port
is connected to the network equipment
(such as PC) through network patch cord.
Product Applications
Technical Parameters
CAT5
◆ IP cameras system based on coaxial cable or telephone line
1 meter
92Mbps
◆ Visual doorbell intercom system based on coaxial cable or
1000 meters
65Mbps
1500 meters
42Mbps
2000 meters
25Mbps
telephone line.
◆ Smart home, POS machine, broadband smart grid.
RG59 (SYV75-5)
1 meter
91Mbps
2 nodes, 1000 meters
81Mbps
2 nodes, 2000 meters
35Mbps
8 nodes, 1 meter
91Mbps
8 nodes, 1000 meters
50Mbps
◆ Railway, telecommunications, oil exploration and coal
mining and other industrial fields.
Page 3 of 6
Complete Installation Guide
Cable Spec and Transmission Characteristics
Category
Description
Available Voltage Range
12VDC
Power Consumption
1.5W
Standard Compliance
IEEE1901, IEEE802.3
Up down agreement
CSMA/CA
Physical speed
240Mbps
Encryption way
128-bit AES Encryption
MTBF
30000 hours
Dimensions (L × W × H)
105mm×65mm×25mm
(including the terminal length)
Material
Aluminum
Net weight
120g/PC
Power
Transmission/ Rate
Reliability
Product Physical Characteristic
Working Temperature
-45℃ ⊥ 85℃
Storage Temperature
-55℃ ⊥ 125℃
Working Humidity
20 ⊥ 85%
Storage Humidity
10 ⊥ 90
Operating Environment
The above data for TCP throughput, is the measured data in the actual environment. The maximum physical layer data is
240Mbps. For coaxial cable transmission, performance is more stable, but it also affected by the cable and terminal matching
methods. On 1000 meters cable, accessing eight nodes, the distance between two nodes is 100 meters apart; The above tests
are all finished in the field test.
Page 4 of 6
Complete Installation Guide
Accessory and Cable Tips
Use EIA/TIA568B standard to
make RJ45 terminal
Power Adapter: DC12V/1A (Optional)
Cables
Telephone Line: CAT3 telephone
Power Line Choose two-wire of RVV RVS RVVP RVB
Twisted Pair: CAT5 or above
Coaxial Cable: RG 59 or above
Product Use Notes
1. Signal transmission cable must be the copper cable. Other material cables will cause the decrease of signal transmission
quality and distance.
2. Transmitting data network signal by mixing twisted pair, telephone line, coax cable or Power Line connection is available
3. This device has no waterproof design. Please use the product in dry environment.
4. Please choose matching power supply specification (DC12V/1A) to supply power for devices respectively.
5. Please do careful setting before using: Let Local switch in MASTER side, other remote devices in SLAVE side. There is only
one Local in a line, otherwise it can not transmit network signal.
6. Long-distance cable connections must be standard connection method, such as welding or use connectors.
7. If the devices fail, you do not disassemble or repair, please contact us timely.
Page 5 of 6
Complete Installation Guide
Application Field Cases
Digital visual intercom Application:
Now within IP development, digital visual intercom is replacing analog non-visual intercom. Using Ethernet Media Converter can
realize multi-signal transmission via any two-wire copper line, optimize arrangement of wires and testing of equipments problem.
Elevator System Application:
It is widely used in elevator system. We can transmit data network signals with two-wire in traveling cables. The only thing
customers do is to install Ethernet Media Converter at both sides of the cables. It is perfect for IP surveillance and analog system
upgrade in elevator. Besides, network information publishing platforms in the elevator also need the support of Ethernet Media
Converter.
Attentions: The device may be a little hot at work. It is normal phenomenon. Specifications are subject to change
without notice.
Page 6 of 6