MVP - TCODE - PRO
Powered by ADVANCED DIAGNOSTICS USA
TOYOTA
This section contains:
• TOYOTA (ADS-125)
• TOYOTA 2007 (ADS-150)
• TOYOTA 2010 (ADS-174)
• TOYOTA 2013 (ADS-199)
(Optional software on some TCode units)
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
535
MVP - TCODE - PRO
Powered by ADVANCED DIAGNOSTICS USA
Toyota Immobilizer
TYPE 1
ALL Toyota TYPE 1 use what the industry refers to as a 4C transponder chip in
the keys.
The same 4C chip can be programmed into the car as a MASTER or as a VALET
key.
A key that is programmed as a VALET cannot be used to introduce more keys
into the system with the MVP or T-Code.
How to tell if a programmed key is a MASTER or a VALET?
Valet key- when first inserted into the ignition lock, the Security Light will stay on for 2
seconds and then stay off.
Master key- when inserted into the ignition lock, the Security Light will not illuminate at
all.
TYPE 1 SPECIAL FUNCTIONS:
RESET Immobilizer:
This function allows you to erase all keys and to place the immobilizer in the “Auto
Learn Mode”. This function is used when the customer has lost all their keys.
ADD MASTER KEY:
This function allows you to add a Master key to the car’s immobilizer system as long as
you have an existing pre-programmed Master key to start with. On Type 1 system cars
it is possible to program a key in as Valet as a Master
ADD VALET KEY:
This function allows you to add a Valet key to the car’s immobilizer system as long as
you have an existing pre-programmed Master key to start with. The vehicle’s immobilizer system cannot tell the difference between the transponder chip in the key,
so it is possible to program a Master as a Valet into the immobilizer system.
ERASE KEYS:
This function allows you to erase all keys except the key in the ignition lock at the time.
536
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
Mpowered
V P & ADVANCED DIAGNOSTICS
TOYOTA
USA
by
TCODE
TOYOTA
ADVANCED
DIAGNOSTICS USA
M V Ppowered
&
by
TCODE
RESET Immobilizer - TYPE 1
(Use this method if you have no Master Keys.)
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
VEHICLE SELECTION
> Immobilizer
REMOTE
VEHICLE SELECTION
> TYPE 1
TYPE 2
DIAGNOSTIC MENU
> RESET Immobilizer
ADD MASTER KEY
ADD VALET KEY
ERASE KEYS
Note: This will cause ALL keys to be
erased and put the Immobilizer system
into “Auto Learn Mode”
RESET Immobilizer
GAINING ACCESS
TIME REQUIRED 16:00
TIME ELAPSED 0:28
Note: Do not be impatient.
Some vehicles may go over 16 minutes.
If the timer goes over 35 minutes - stop.
Disconnect from the OBD2 port and remove the key. Wait 20 sec. and start over.
RESET Immobilizer
PROCEDURE COMPLETE
PRESS ENTER KEY
ECU IDENTIFICATION
TOYOTA/LEXUS TYPE 1
PRESS ENTER KEY
DIAGNOSTIC MENU
ECU IDENTIFICATION
FAULT CODES
> SPECIAL FUNCTIONS
Once you have PROCEDURE COMPLETE on the tester, look at the immobilizer
light.
The Security Light can be in 2 shapes:
> A small blinking red circle next to the word “Security”, or
> A blinking red light in the shape of a car.
The light should now be solid indicating that the Immobilizer system has been
Reset and the vehicle is now in Auto Learn mode Insert each key you want to
program - but do not turn the key ON, only insert and remove after 5 seconds.
The vehicle may learn up to 3 keys this way and the Auto Learn mode should close
once the 3rd key is presented. The last key presented will be programmed in as
Valet key.
If you have less than 3 keys to program You can close the Auto Learn mode early
by pressing the brake pedal 6-8 times, very fast. (You must use a Master key for
this.)
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
537
MVP &
TCODE
TOYOTA
ADVANCED DIAGNOSTICS USA
powered
by
ADD MASTER KEY - TYPE 1
Insert a Master key that is already registered into the vehicle. Turn the ignition lock to the “ON”
position. The Security Light must be out when the key is in. Connect and follow screens.
NOTE: If you do not have an existing Master key, you must use the “Reset Immobilizer” procedure to Reset
the Immobilizer system. A Valet key will not work as a substitute for a Master Key.
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
VEHICLE SELECTION
> Immobilizer
REMOTE
VEHICLE SELECTION
> TYPE 1
TYPE 2
DIAGNOSTIC MENU
ADD MASTER KEY
ECU IDENTIFICATION
FAULT CODES
> SPECIAL FUNCTIONS
TIME ELAPSED: 2 S
DIAGNOSTIC MENU
RESET Immobilizer
> ADD MASTER KEY
ADD VALET KEY
ERASE KEYS
Note: This usually takes about 60 seconds.
If the timer goes past 120 seconds, stop.
The key is most likely now programmed.
Disconnect & try key.
ADD MASTER KEY
ADD MASTER KEY
WARNING
FOLLOW NEXT SCREENS
QUICKLY & CAREFULLY
PROCEDURE COMPLETE
PRESS ENTER KEY
TIME ELAPSED: 59 S
PRESS ENTER KEY
ADD MASTER KEY
SWITCH IGNITION ON
PRESS ENTER KEY
ECU IDENTIFICATION
TOYOTA/LEXUS TYPE 1
PRESS ENTER KEY
538
SWITCH IGNITION OFF
REMOVE MASTER KEY
WITHIN 20 Sec
AND THEN PRESS ENTER
TIME ELAPSED: 1 S
ADD MASTER KEY
INSERT NEW MASTER KEY
WITHIN 10 Sec
LEAVE IGNITION OFF
AND THEN PRESS ENTER
TIME ELAPSED: 0 S
Note: If you get an Error message screen:
disconnect from the OBD2 port and
remove the key. Wait 20 seconds and
start over. On this Type, each key must
be added separately. Disconnect from the
OBD2 port and remove the key. Wait 20
seconds and start over to add another key.
Note: Read carefully & follow the
screen prompts.
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
powered
by
ADVANCED DIAGNOSTICS USA
MVP &
TCODE
TOYOTA
ADD VALET KEY - TYPE 1
Insert a Master key that is already registered into the vehicle. Turn the ignition lock to the “ON”
position. The Security Light must be out when the key is in. Connect and follow screens.
NOTE: If you do not have an existing Master key, you must use the “Reset Immobilizer” procedure to Reset
the Immobilizer system. A Valet key will not work as a substitute for a Master Key.
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
VEHICLE SELECTION
> Immobilizer
REMOTE
VEHICLE SELECTION
> TYPE 1
TYPE 2
DIAGNOSTIC MENU
ADD VALET KEY
ECU IDENTIFICATION
FAULT CODES
> SPECIAL FUNCTIONS
TIME ELAPSED: 2 S
DIAGNOSTIC MENU
RESET Immobilizer
ADD MASTER KEY
> ADD VALET KEY
ERASE KEYS
Note: This usually takes about 60 seconds.
If the timer goes past 120 seconds, stop.
The key is most likely now programmed.
Disconnect & try key.
ADD VALET KEY
ADD VALET KEY
WARNING
FOLLOW NEXT SCREENS
QUICKLY & CAREFULLY
PROCEDURE COMPLETE
PRESS ENTER KEY
TIME ELAPSED: 59 S
PRESS ENTER KEY
ADD VALET KEY
SWITCH IGNITION ON
PRESS ENTER KEY
ECU IDENTIFICATION
TOYOTA/LEXUS TYPE 1
PRESS ENTER KEY
SWITCH IGNITION OFF
REMOVE MASTER KEY
WITHIN 20 Sec
AND THEN PRESS ENTER
TIME ELAPSED: 1 S
ADD VALET KEY
INSERT NEW VALET KEY
WITHIN 10 Sec
LEAVE IGNITION OFF
AND THEN PRESS ENTER
TIME ELAPSED: 0 S
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
Note: If you get an Error message screen,
disconnect from the OBD2 port and
remove the key. Wait 20 seconds and
start over. On this Type, each key must
be added separately. Disconnect from the
OBD2 port and remove the key. Wait 20
seconds and start over to add another key.
Note: Read carefully & follow the
screen prompts.
539
M
MVVPP &&
TCODE
TCODE
powered
TOYOTA
PRIUS
‘04-’09
powered
ADVANCED
ADVANCED
DIAGNOSTICS
DIAGNOSTICS
USA
USA
by
by
ERASE KEYS - TYPE 1
Insert a Master key that is already registered into the vehicle. Turn the ignition lock to the “ON”
position. The Security Light must be out when the key is in. Connect and follow screens.
NOTE: If you do not have an existing Master key, you must use the “Reset Immobilizer” procedure to Reset
the Immobilizer system. A Valet key will not work as a substitute for a Master Key.
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
VEHICLE SELECTION
> Immobilizer
REMOTE
DIAGNOSTIC MENU
ECU IDENTIFICATION
FAULT CODES
> SPECIAL FUNCTIONS
DIAGNOSTIC MENU
RESET Immobilizer
ADD MASTER KEY
ADD VALET KEY
> ERASE KEYS
PLEASE WAIT
TRYING TO COMMUNICATE
ERASE KEYS
PROCEDURE COMPLETE
PRESS ENTER KEY
VEHICLE SELECTION
> TYPE 1
TYPE 2
ERASE KEYS
WARNING
FOLLOW NEXT SCREENS
QUICKLY & CAREFULLY
PRESS ENTER KEY
Note: If you get an Error message screen,
disconnect and remove the key.
Wait 20 seconds and start over.
ERASE KEYS
SWITCH IGNITION ON
PRESS ENTER KEY
540
SWITCH IGNITION OFF
REMOVE MASTER KEY
WITHIN 10 Sec
TIME ELAPSED: 1 S
ECU IDENTIFICATION
ERASE KEYS
LEXUS TYPE 1
INSERT MASTER KEY
SWITCH IGNITION ON
PRESS ENTER KEY
PRESS ENTER KEY
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
Mpowered
V P & ADVANCED
TOYOTA USA
ADVANCEDDIAGNOSTICS
DIAGNOSTICS
USA
by
TCODE
TOYOTA
PRIUS
‘04-’09
ADVANCED
DIAGNOSTICS
USA
M V Ppowered
&
by
TCODE
Toyota Immobilizer
TYPE 2
Use the KEY LOOK UP GUIDE to determine proper key blanks to use.
There are various aftermarket version of these keys you can use.
When in doubt check with the dealer for the exact part number
for the key.
ALL Toyota TYPE 2 use what the industry refers to as a 4D transponder chip in the keys.
Factory 4D chips can come in two varieties MASTER and VALET.
Factory keys with grey plastic heads have a VALET type & chip cannot be used to perform a
RESET or to introduce more keys into the system with the MVP or T-Code.
How to tell if a programmed key is a MASTER or a VALET?
Valet key- when first inserted into the ignition lock, the Security Light will stay on for 2 seconds and then stay off.
Master key- when inserted into the ignition lock, the Security Light will not illuminate at all.
TYPE 2 SPECIAL FUNCTIONS:
“QUICK” RESET Immobilizer: (“NEW” Available on Type 2 Immobilizer)
This function allows you to erase all keys and to place the immobilizer in “Auto Learn Mode”
instantly without having to go thru the 16 or 30 minute security delay found on the older regular Reset. This function is used when the customer has lost all their Master keys.
“REGULAR” RESET Immobilizer: (Old way of resetting with security delay, now replaced
with QUICK RESET) This function allows you to erase all keys and to place the immobilizer
in the “Auto Learn Mode”. This function is used when the customer has lost all their Master
keys and the Quick Reset can’t be used (See Below)
In some cases it maybe necessary to use the old timed access reset because sometimes the
quick reset will only let you program TWO keys and no more than that. (Rare, but possible)
PROGRAM KEY: This function allows you to add a Master key to the car’s immobilizer system as long as you have an existing pre-programmed Master key to start with.
ERASE KEYS: This function allows you to erase all keys except the key in the ignition lock
at the time.
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
541
M
M
MV
VVP
PP &
&&
TCODE
TCODE
TCODE
TOYOTA
TOYOTA
PRIUS
‘04-’09
powered
powered
powered
ADVANCED
DIAGNOSTICS
USA
by
ADVANCED
ADVANCED
DIAGNOSTICS
DIAGNOSTICS
USA
USA
by
by
Quick” RESET Immobilizer - TYPE 2
(Use this method if you have no Master Keys.)
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
DIAGNOSTIC MENU
RESET Immobilizer
PROGRAM KEY
ERASE KEYS
> QUICK RESET Immobilizer
QUICK RESET IMMOBILIZER
This will RESET the immobilizer and place
the system in “AUTO LEARN MODE”
Within just seconds.
VEHICLE SELECTION
> Immobilizer
REMOTE
VEHICLE SELECTION
TYPE 1
> TYPE 2
TYPE 3
TYPE 4
TYPE 5
TRYING TO COMMUNICATE
RESET Immobilizer
PROCEDURE COMPLETE
RESET Immobilizer
OR
PRESS ENTER KEY
COMMUNICATION FAILED
PRESS ENTER KEY
Both are OK
SWITCH IGNITION ON
WATCH THE SECURITY LIGHT!
PRESS ENTER KEY
ECU IDENTIFICATION
TOYOTA/LEXUS TYPE 2
PRESS ENTER KEY
DIAGNOSTIC MENU
ECU IDENTIFICATION
FAULT CODES
LIVE DATA
ACTUATORS
> SPECIAL FUNCTIONS
542
Most of the time you will see PROCEDURE COMPLETE message on the tester.
However, sometimes the car does not signal the tester that the immobilizer has been
reset and you may see COMMUNICATION FAILED on the screen.
DO NOT WATCH THE TESTER,
WATCH THE CARS SECURITY LIGHT!
Auto Learn mode is indicated by the steady illumination of the Security Light.
Once you see a solid immo light. Insert each key you want to program - but do not turn
the key ON - only insert and remove after 5 seconds. The vehicle may learn up to 4 keys
before the Auto Learn cycle is shut down.
You can close the cycle early by turning the ignition lock from Off to On and back to Off
6-8 times, very fast, with a Master key. Remove the key and re-insert it and the Security
Lite should be out when there is a programmed key in the ignition.
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
Mpowered
V P & ADVANCED
TOYOTA USA
ADVANCEDDIAGNOSTICS
DIAGNOSTICS
USA
by
TCODE
TOYOTA
PRIUS
‘04-’09
ADVANCED
DIAGNOSTICS
USA
M V Ppowered
&
by
TCODE
“Regular” RESET Immobilizer - TYPE 2
Old way of doing a Type 2 Reset, (use only in rare instances, see notes)
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
The quick reset on the previous page can be used
99% of the time and the old method shown here
is almost NEVER needed. However in some rare
instances the quick reset may only allow TWO keys
to be programmed. In these cases you can still use
the old method with the security delay, after which 3
or 4 keys can be introduced successfully.
VEHICLE SELECTION
> Immobilizer
REMOTE
DIAGNOSTIC MENU
> RESET Immobilizer
PROGRAM KEY
ERASE KEYS
Note: This will cause ALL keys to be
erased and the Immobilizer system to
reset itself.
VEHICLE SELECTION
TYPE 1
> TYPE 2
RESET Immobilizer
Note: Do not be impatient.
Some vehicles may go over 30 minutes.
If the timer goes over 40 minutes - stop.
Disconnect from the OBD2 port and remove the key. Wait 20 sec. and start over.
GAINING ACCESS
TIME REQUIRED 30:00
TIME ELAPSED 0:28
RESET Immobilizer
SWITCH IGNITION ON
PROCEDURE COMPLETE
PRESS ENTER KEY
ECU IDENTIFICATION
TOYOTA/LEXUS TYPE 2
PRESS ENTER KEY
DIAGNOSTIC MENU
ECU IDENTIFICATION
FAULT CODES
LIVE DATA
ACTUATORS
> SPECIAL FUNCTIONS
PRESS ENTER KEY
1
2
Note: You must remove the Master key &
Disconnect at this point.
The Immobilizer system is now Reset. If
you insert the correct transponder type
key, the Security Light should remain
steady & illuminated.
The vehicle is now in Auto Learn mode. Auto Learn mode is indicated by the steady
illumination of the Security Light. Insert each key you want to program - but do not
turn the key ON - only insert and remove after 5 seconds. The vehicle
may learn up to 4 keys before the Auto Learn cycle is shut down.
You can close the cycle early by turning the ignition lock from Off to On and back to Off 5
times, very fast, with a Master key. Remove the key and re-insert it and the Security Lite
should be out when there is a programmed key in the ignition.
On this type of vehicle, the Immobilizer computer can tell the difference between a Master
& Valet key by the type of transponder in the key.
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
543
M
M
VVPP && ADVANCED DIAGNOSTICS
powered
TOYOTA
PRIUS
‘04-’09USA
by
TCODE
TCODE
M V Ppowered
&
TCODE
powered
TOYOTA
ADVANCED
ADVANCED
DIAGNOSTICS
DIAGNOSTICS
USA
USA
by
by
ADD MASTER or VALET KEY - TYPE 2
Insert a Master key that is already registered into the vehicle. Turn the ignition lock to the “ON”
position. The Security Light must be out when the key is in. Connect and follow screens.
NOTE: If you do not have an existing Master key, you must use the “Reset Immobilizer” procedure to Reset
the Immobilizer system. A Valet key will not work as a substitute for a Master Key.
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
VEHICLE SELECTION
> Immobilizer
REMOTE
VEHICLE SELECTION
TYPE 1
> TYPE 2
DIAGNOSTIC MENU
ECU IDENTIFICATION
FAULT CODES
LIVE DATA
ACTUATORS
> SPECIAL FUNCTIONS
PROGRAM KEY
PLEASE WAIT
TIME ELAPSED: 2 S
DIAGNOSTIC MENU
RESET Immobilizer
> PROGRAM KEY
ERASE KEYS
PROGRAM KEY
SWITCH IGNITION OFF
REMOVE KEY
INSERT KEY
SWITCH IGNITION ON
WITHIN 120 Sec
TIME ELAPSED: 0 S
PRESS ENTER KEY
Note: This usually takes about 60 seconds.
If the timer goes past 120 seconds, stop.
The key is most likely now programmed.
Disconnect & try key.
PROGRAM KEY
PROCEDURE COMPLETE
TIME ELAPSED: 59 S
PRESS ENTER KEY
PROGRAM KEY
SWITCH IGNITION ON
PRESS ENTER KEY
PRESS ENTER KEY
ECU IDENTIFICATION
PROGRAM KEY
TOYOTA/LEXUS TYPE 2
PRESS ENTER KEY
544
SWITCH IGNITION OFF
REMOVE KEY
WITHIN 20 Sec
TIME ELAPSED: 0 S
INSERT NEW KEY
LEAVE IGNITION OFF
WITHIN 10 Sec
TIME ELAPSED: 0 S
Note: You must remove the Master
key & then press enter.
Note: You must insert the New key
but do not turn it.
Press Enter when done.
PRESS ENTER KEY
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
Mpowered
V P & ADVANCED
TOYOTA USA
ADVANCEDDIAGNOSTICS
DIAGNOSTICS
USA
by
TCODE
TOYOTA
PRIUS
‘04-’09
ADVANCED
DIAGNOSTICS
USA
M V Ppowered
&
by
TCODE
ERASE KEYS - TYPE 2
Insert a Master key that is already registered into the vehicle. Turn the ignition lock to the “ON”
position. The Security Light must be out when the key is in. Connect and follow screens.
NOTE: If you do not have an existing Master key, you must use the “Reset Immobilizer” procedure to Reset
the Immobilizer system. A Valet key will not work as a substitute for a Master Key.
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
VEHICLE SELECTION
> Immobilizer
REMOTE
DIAGNOSTIC MENU
ECU IDENTIFICATION
FAULT CODES
LIVE DATA
ACTUATORS
> SPECIAL FUNCTIONS
ERASE KEYS
PROCEDURE COMPLETE
PRESS ENTER KEY
DIAGNOSTIC MENU
RESET Immobilizer
PROGRAM KEY
> ERASE KEYS
Note: If you get an Error
message screen, disconnect and
remove the key.
Wait 20 seconds and start over.
VEHICLE SELECTION
TYPE 1
> TYPE 2
SWITCH IGNITION ON
ERASE KEYS
SWITCH IGNITION OFF
REMOVE KEY
INSERT KEY
SWITCH IGNITION ON
WITHIN 120 Sec
TIME ELAPSED: 0 S
PRESS ENTER KEY
PLEASE WAIT
TRYING TO COMMUNICATE
PRESS ENTER KEY
ECU IDENTIFICATION
LEXUS TYPE 1
ERASE KEYS
SWITCH IGNITION OFF
REMOVE KEY
WITHIN 10 Sec
TIME ELAPSED: 0 S
PRESS ENTER KEY
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
545
MVP - TCODE - PRO
Powered by ADVANCED DIAGNOSTICS USA
Toyota
Key Programming
TOYOTA 2007
ADS-150
(Optional Software on all TCode Units.)
546
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
powered
by
ADVANCED DIAGNOSTICS USA
TOYOTA
MVP &
TCODE
TOYOTA 2007
Types of Keys & Remote Head Keys in Use
A “DOT” on the key blade
usually indicates the key has
a Texas Instruments 4D type
chip inside
Toyota Factory Key
Non-Remote Head Key
89785-08020 or 89785-60160
Toyota Factory Remote Head Key
2007 Camry
89070-33881
Use the KEY LOOK UP GUIDE to determine proper key blanks to use.
There are various aftermarket version of these keys you can use.
When in doubt check with the dealer for the exact part number
of the key or remote.
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
547
MVP &
TCODE
TOYOTA
ADVANCED DIAGNOSTICS USA
powered
by
Toyota Immobilizer
TYPE 4
Use the KEY LOOK UP GUIDE to determine proper key blanks to use.
There are various aftermarket version of these keys you can use.
When in doubt check with the dealer for the exact part number
for the key.
ALL Toyota TYPE 4 use what the industry refers to as a 4D transponder chip in the keys.
Factory 4D chips can come in two varieties MASTER and VALET.
Factory keys with grey plastic heads have a VALET type & chip cannot be used to perform a
RESET or to introduce more keys into the system with the MVP or T-Code.
How to tell if a programmed key is a MASTER or a VALET?
Valet key- when first inserted into the ignition lock, the Security Light will stay on for 2 seconds and then stay off.
Master key- when inserted into the ignition lock, the Security Light will not illuminate at all.
TYPE 4 SPECIAL FUNCTIONS:
“QUICK” RESET Immobilizer: (“NEW” Available on Type 4 Immobilizer)
This function allows you to erase all keys and to place the immobilizer in “Auto Learn Mode”
instantly without having to go thru the 16 or 30 minute security delay found on the older regular Reset. This function is used when the customer has lost all their Master keys.
“Regular” RESET Immobilizer: (Old way of resetting with security delay, now replaced with
QUICK RESET) This function allows you to erase all keys and to place the immobilizer in the
“Auto Learn Mode”. This function is used when the customer has lost all their Master keys
and the Quick Reset can’t be used (See Below)
In some cases it maybe necessary to use the old timed access reset because sometimes the
quick reset will only let you program TWO keys and no more than that. (Rare, but possible)
RESET ECU: This procedure needs to be completed after RESET Immobiliser to re sync the
cars immobilizer and ECU. (Not needed after Quick Reset as Quick Reset includes an ECU)
PROGRAM KEY: This function allows you to add a Master key to the car’s immobilizer system as long as you have an existing pre-programmed Master key to start with.
ERASE KEYS: This function allows you to erase all keys except the master key in the ignition lock at the time.
548
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
powered
by
MVP &
TCODE
TOYOTA
ADVANCED DIAGNOSTICS USA
QUICK RESET Immobilizer - TYPE 4
(Use this method if you have no Master Keys.)
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
DIAGNOSTIC MENU
RESET Immobilizer
PROGRAM KEY
ERASE KEYS
> QUICK RESET Immobilizer
QUICK RESET IMMOBILIZER
This will RESET the immobilizer and place
the system in “AUTO LEARN MODE”
Within just seconds. On Type 4 this also
performs the ECU Reset.
VEHICLE SELECTION
> Immobilizer
REMOTE
VEHICLE SELECTION
TYPE 1
TYPE 2
TYPE 3
> TYPE 4
TYPE 5
TRYING TO COMMUNICATE
RESET Immobilizer
RESET Immobilizer
PROCEDURE COMPLETE
OR
COMMUNICATION FAILED
PRESS ENTER KEY
PRESS ENTER KEY
Both are OK
SWITCH IGNITION ON
PRESS ENTER KEY
ECU IDENTIFICATION
WATCH THE SECURITY LIGHT!
Most of the time you will see PROCEDURE COMPLETE message on the tester.
However, sometimes the car does not signal the tester that the immobilizer has been
reset and you may see COMMUNICATION FAILED on the screen.
TOYOTA/LEXUS TYPE 4
DO NOT WATCH THE TESTER,
WATCH THE CARS SECURITY LIGHT!
PRESS ENTER KEY
Auto Learn mode is indicated by the steady illumination of the Security Light.
Once you see a solid immo light. Insert each key you want to program - but do not turn
the key ON - only insert and remove after 5 seconds. The vehicle may learn up to 4 keys
before the Auto Learn cycle is shut down.
You can close the cycle early by turning the ignition lock from Off to On and back to Off
6-8 times, very fast, with a Master key. Remove the key and re-insert it and the Security
Lite should be out when there is a programmed key in the ignition.
DIAGNOSTIC MENU
ECU IDENTIFICATION
FAULT CODES
LIVE DATA
ACTUATORS
> SPECIAL FUNCTIONS
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
549
MVP &
TCODE
TOYOTA
ADVANCED DIAGNOSTICS USA
powered
by
STANDARD RESET Immobilizer - TYPE 4
Old way of doing a Type 4 Reset, (use only in rare instances, see note)
NOTE: The quick reset on the previous page can be used 99% of the time and the old method shown
here is almost NEVER needed. However in some rare instances the quick reset may only allow TWO
keys to be programmed. In these cases you can still use the old method with the security delay, after
which 3 or 4 keys can be introduced successfully.
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
ECU IDENTIFICATION
RESET Immobilizer
TOYOTA/LEXUS TYPE 4
PROCEDURE COMPLETE
PRESS ENTER KEY
PRESS ENTER KEY
DIAGNOSTIC MENU
VEHICLE SELECTION
> Immobilizer
REMOTE
PROXIMITY
VEHICLE SELECTION
TYPE 1
TYPE 2
TYPE 3
> TYPE 4
ECU IDENTIFICATION
FAULT CODES
LIVE DATA
ACTUATORS
> SPECIAL FUNCTIONS
DIAGNOSTIC MENU
> RESET Immobilizer
PROGRAM KEY
ERASE KEYS
RESET ECU
Now you must
RESET the ECU.
DIAGNOSTIC MENU
RESET Immobilizer
PROGRAM KEY
ERASE KEYS
> RESET ECU
RESET Immobilizer
SWITCH IGNITION ON
GAINING ACCESS
TIME REQUIRED 30:00
TIME ELAPSED 0:28
PRESS ENTER KEY
RESET ECU
PROCEDURE COMPLETE
PRESS ENTER KEY
Note: You must remove the Master key & Disconnect the tester at this point.
The Immobilizer system is now Reset. The Security Light should remain steady & illuminated.
The vehicle is now in Auto Learn mode. Auto Learn mode is indicated by the steady illumination of the Security Light. Insert each key
you want to program - but do not turn the key on - only insert and remove after 4 seconds. The vehicle may learn up to 4 keys before
the Auto Learn cycle is shut down.
You can close the cycle early by turning the ignition lock from Off to On and back to Off 6 times, very fast, with a Master key.
Remove the key and re-insert it and the Security should be out when there is a programmed in the ignition.
550
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
powered
by
ADVANCED DIAGNOSTICS USA
MVP &
TCODE
TOYOTA
PROGRAM KEYS - TYPE 4
(Use this method if you have at least 1 Master Key.)
NOTE: If you do not have an existing Master key you must use the “Reset Immobilizer” procedure to Reset
the Immobilizer system. A Valet key will not work as a substitute for a Master Key.
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
VEHICLE SELECTION
> Immobilizer
REMOTE
PROXIMITY
VEHICLE SELECTION
TYPE 1
TYPE 2
TYPE 3
> TYPE 4
DIAGNOSTIC MENU
PROGRAM KEY
ECU IDENTIFICATION
FAULT CODES
LIVE DATA
ACTUATORS
> SPECIAL FUNCTIONS
INSERT NEW KEY
LEAVE IGNITION OFF
WITHIN 10 Sec
TIME ELAPSED: 0 S
PRESS ENTER KEY
DIAGNOSTIC MENU
RESET Immobilizer
> PROGRAM KEY
ERASE KEYS
RESET ECU
Note: You must insert the New key,
but Do Not turn it.
Press Enter when done.
PROGRAM KEY
SWITCH IGNITION OFF
REMOVE KEY
INSERT KEY
SWITCH IGNITION ON
WITHIN 120 Sec
TIME ELAPSED: 0 S
PRESS ENTER KEY
PROGRAM KEY
PLEASE WAIT
TIME ELAPSED: 2 S
PROGRAM KEY
SWITCH IGNITION ON
PRESS ENTER KEY
ECU IDENTIFICATION
TOYOTA/LEXUS TYPE X
SWITCH IGNITION OFF
REMOVE KEY
WITHIN 20 Sec
TIME ELAPSED: 0 S
Note: This usually takes about 60 seconds.
If the timer goes past 120 seconds, stop.
The key is most likely now programmed.
Disconnect & try key.
PRESS ENTER KEY
PROGRAM KEY
Note: You must remove the
Master key & then press
enter.
PRESS ENTER KEY
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
PROCEDURE COMPLETE
TIME ELAPSED: 59 S
PRESS ENTER KEY
551
MVP &
TCODE
TOYOTA
ADVANCED DIAGNOSTICS USA
powered
by
TOYOTA TYPE 4 IMMOBILIZER
Troubleshooting:
Problem: After a Reset, the car starts and runs but the theft light blinks.
Solution: The car is still in “learn mode” close the learning cycle by turning the ignition ON/OFF quickly at least
6-8 times until the light goes out.
Problem: Program key goes all the way thru to a successful conclusion with no errors but the car cranks and
does not start.
Solution: Barring any other problems (low fuel, failed components etc) the car key memory may be full. Meaning
8 keys are already programmed and no more can be added. Use ERASE KEYS with a MASTER KEY and this
will ERASE all keys except the 1 Master Key used. Now go back and use PROGRAM KEY to add any other keys
you want to program.
Toyota Remote
GRID INDEX
- Only the models listed are supported -
TOYOTA
MODELS
YEARS
SYSTEM TYPE
S/W
T-CODE
4-RUNNER
2007-2013
REMOTE 2
ADS-125
AVALON
2010-2013
REMOTE 2
ADS-125
CAMRY
2007-2013
REMOTE 4
ADS-150
COROLLA
Mid 2010-2013
REMOTE 4
ADS-150
FJ CRUISER
2010-2012
REMOTE 4
ADS-150
HIGHLANDER
2005-2006
REMOTE 4
ADS-150
LAND CRUISER
2003-2013
REMOTE 2
ADS-125
RAV-4
2007-2013
REMOTE 4
ADS-150
SEQUOIA
2003-2013
REMOTE 4
ADS-125
SIENNA
2010-2013
REMOTE 4
ADS-150
TUNDRA
2003
REMOTE 2
ADS-125
TUNDRA
2007-2013
REMOTE 4
ADS-150
VENZA
2010-2013
REMOTE 4
ADS-150
552
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
powered
by
MVP &
TCODE
TOYOTA
ADVANCED DIAGNOSTICS USA
PROGRAM REMOTE - TYPE 4
(Use this method to program the Remote portion of remote head keys
And also for programming separate remotes)
The RKE program separate from
the transponder on LEXUS &
TOYOTA remote head keys
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
ECU IDENTIFICATION
TOYOTA TYPE 4
PRESS ENTER KEY
DIAGNOSTIC MENU
VEHICLE SELECTION
Immobilizer
> REMOTE
PROXIMITY
VEHICLE SELECTION
TYPE 1
> TYPE 2
TYPE 3
> TYPE 4
Use the Grid earlier in this section for proper system selection.
PROGRAM REMOTE
PRESS LOCK & UNLOCK
TOGETHER FOR 4 Sec.
PRESS UNLOCK BUTTON
FOR 1 SEC
BACK’ TO EXIT
ECU IDENTIFICATION
> SPECIAL FUNCTIONS
DIAGNOSTIC MENU
ERASE REMOTES
> PROGRAM REMOTE
Note: Press the Lock & Unlock
buttons together for 4 seconds
and quickly press Unlock button
for 1 second. You must be fast
on the button operation.
PRESS the BACK
BUTTON to COMPLETE
THE PROGRAMMING.
PROGRAM REMOTE
PROGRAM REMOTE
SYSTEM WILL BEEP
WHEN COMPLETE
PROCEDURE COMPLETE
PRESS ENTER KEY
PRESS ENTER KEY
SWITCH IGNITION ON
PRESS ENTER KEY
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
553
MVP &
TCODE
TOYOTA
ADVANCED DIAGNOSTICS USA
powered
by
TOYOTA 2007
Examples of different Types of PROX
Toyota Avalon PROX
89904-07030
Toyota Camry PROX
89904-06041
Lexus ES / GS / IS PROX
89904-30270
Always check with the dealer for the exact part number of Prox to
use on the vehicle you are working on.
These are just a few examples shown for 2007 models. For later
years there are quite a few different part numbers some interchangeable and some not!
Used Toyota/Lexus Proximity key warning!
Prox keys that are not BRAND NEW cannot be simply ADDED.
There is a work around trick that will usually allow you to program in an already used Prox.
1. Perform an Immobilizer reset introducing the used key first.
2. Once you have the used key programmed and working use PROGRAM PROX
to add back in the original working Prox key(s).
MVP users take note: The above method may not always work 100%.
Brand new keys from a reputable dealer is what we recommend.
These program in 100% without issue.
Cross Interference:
It has been our experience that on occasion there can be cross signal interference when 2 or more Prox remotes are in the
vehicle at the same time. During Programming keep only one Prox remote in the car at a time because of this.
Weak Prox Batteries:
Also, when using NEW Prox remotes if they get a failure it can be because the battery in the Prox is slightly weak from
sitting around in the parts dept. and may not program in until the Prox battery is changed.
554
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
powered
by
ADVANCED DIAGNOSTICS USA
MVP &
TCODE
TOYOTA
RESET Immobilizer - PROX
(Use this method if you have no PROX Remotes)
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
DIAGNOSTIC MENU
ECU IDENTIFICATION
ACTUATORS
> SPECIAL FUNCTIONS
VEHICLE SELECTION
Immobilizer
REMOTE
> PROXIMITY
Use the Key Look up guide
for proper system selection.
VEHICLE SELECTION
TYPE 1
TYPE 2
TYPE 3
TYPE 4
DIAGNOSTIC MENU
PROGRAM KEY
ERASE KEYS
> RESET Immobilizer
ID REG ENG START
ID REG SMART BOX
RESET Immobilizer
PLEASE ENSURE THAT
THE DRIVER DOOR IS
OPEN DURING THE
PROCEDURE
(Disregard this Step)
PRESS ENTER KEY
> PROGRAM KEY
ERASE KEYS
RESET Immobilizer
ID REG ENG START
ID REG SMART BOX
PROGRAM KEYS
NUMBER OF KEYS
0 ( 4 MAX )
PRESS ENTER KEY
RESET Immobilizer
PROGRAM KEYS
TIME REQUIRED 16:00
TIME ELAPSED 0:28
BACK’ TO EXIT
ECU IDENTIFICATION
RESET Immobilizer
SMART KEY
PROCEDURE COMPLETE
PRESS ENTER KEY
DIAGNOSTIC MENU
PRESS ENTER KEY
GAINING ACCESS
SWITCH IGNITION ON
Now that the immobilizer
has been RESET go to
PROGRAM KEYS on the
menu
TOUCH ENGINE SW
WITH EMBLEM SIDE
OF REGISTERED KEY
TIME 30
BACK’ TO EXIT
Continued on next page >
PRESS ENTER KEY
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
555
MVP &
TCODE
TOYOTA
ADVANCED DIAGNOSTICS USA
powered
by
RESET Immobilizer - PROX
(Use this method if you have no PROX Remotes)
PROGRAM KEYS
Touch the Emblem side of the PROX
Remote to the START Button on the
dash. The Emblem side is the side
without the buttons on it and has either
the Toyota or Lexus symbol on it.
PROCEDURE COMPLETE
NUMBER OF KEYS
1
PRESS ENTER KEY
PROGRAM KEYS
KEY DETECTED
REMOVE KEY
TIME 30
BACK’ TO EXIT
PROGRAM KEYS
TOUCH ENGINE SW
WITH EMBLEM SIDE
OF REGISTERED KEY
If the Prox is not detected:
1. Check that it’s the correct
part number. (Many look a like
but are incompatible)
2. That the battery inside the
Prox is new.
3. That the battery voltage on
the vehicle is at least 12 volts.
PROGRAM KEYS
PLEASE WAIT
BACK’ TO EXIT
556
TIME 28
PRESS ENTER TO CONT.
If you have more to
program, touch the next
one to the START Button,
otherwise press ENTER
on the tester to finish the
procedure.
We Recommend keeping
only one Prox in the car
at a time. Take any others
outside the car, as we have
seen them interfere with
each other.
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
powered
by
ADVANCED DIAGNOSTICS USA
MVP &
TCODE
TOYOTA
ADD ADDITIONAL PROX
(Use this method if you have at least 1 existing PROX Remote)
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
VEHICLE SELECTION
Immobilizer
REMOTE
> PROXIMITY
VEHICLE SELECTION
TYPE 1
TYPE 2
TYPE 3
TYPE 4
DIAGNOSTIC MENU
> PROGRAM KEY
ERASE KEYS
RESET Immobilizer
ID REG ENG START
ID REG SMART BOX
PROGRAM KEYS
NUMBER OF KEYS
2 ( 4 MAX )
PRESS ENTER KEY
PROGRAM KEYS
TOUCH ENGINE SW
WITH EMBLEM SIDE
OF REGISTERED KEY
TIME 30
PRESS ENTER KEY
ECU IDENTIFICATION
SMART KEY
TOUCH ENGINE SW
WITH EMBLEM SIDE
OF NEXT NEW KEY
TIME 30
BACK’ TO EXIT
If you have more to
program, touch the next
one to the START Button,
otherwise press ENTER
on the tester to finish the
procedure.
PROGRAM KEYS
PLEASE WAIT
BACK’ TO EXIT
BACK’ TO EXIT
SWITCH IGNITION ON
(Disregard this Step)
PROGRAM KEYS
PROGRAM KEYS
Touch the Emblem side of
the PROX Remote to the
START Button on the dash.
The Emblem side is the side
without the buttons on it
and has either the Toyota or
Lexus symbol on it.
PRESS ENTER KEY
DIAGNOSTIC MENU
ECU IDENTIFICATION
ACTUATORS
> SPECIAL FUNCTIONS
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
PROCEDURE COMPLETE
NUMBER OF KEYS
3
PRESS ENTER KEY
“USED PROX KEY WARNING”
Only BRAND NEW keys can be added
successfully 100%. (See front of section)
Also, We Recommend keeping only
one Prox in the car at a time. Take any
others outside the car, as we have seen
them interfere with each other.
557
MVP - TCODE - PRO
Powered by ADVANCED DIAGNOSTICS USA
2010-11 Lexus & Toyota
Key & Prox
ADS-174
Used Toyota/Lexus Proximity key warning!
Prox keys that are not BRAND NEW cannot be simply ADDED.
There is a work around trick that will usually allow you to program in an already used prox.
1. Perform an Immobilizer reset introducing the used key first.
2. Once you have the used key programmed and working use PROGRAM PROX
to add back in the original working Prox key(s).
MVP users take note: The above method may not always work 100%.
Brand new keys from a reputable dealer is what we recommend.
These program in 100% without issue.
(Optional Software on all TCode Units.)
558
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
Mpowered
V P & ADVANCED
TOYOTA USA
ADVANCEDDIAGNOSTICS
DIAGNOSTICS
USA
by
TCODE
TOYOTA
PRIUS
‘04-’09
ADVANCED
DIAGNOSTICS
USA
M V Ppowered
&
by
TCODE
How to find the
System Type on 2010-11
Some models use the new dealer “G” transponder key and some don’t. It is possible to have 2 identical
cars side by side and one still on the older key and one on the “G” key.
Even looking the vehicle up by the VIN can give you the wrong key.
If the customer already has a working key that has the letter “G” stamped on the blade, than another “G”
key will work fine. If not follow the steps below.
There is only 1 way to tell for sure. This is for 2010 & 2011 models.
Before cutting the transponder key - insert a mechanical key in the ignition and turn to the On position.
Go to “RESET Immobilizer” and see if you can communicate with “TYPE 4” - If you can than is NOT a
“G” key vehicle.
Toyota TYPE 4 systems are not “G” transponder key vehicles. They are second generation 4D systems.
Toyota TYPE 5 systems are “G” transponder key vehicles.
Plug into the car and see which system communicates
Communicates with TYPE 4
system
Communicates with TYPE 5
system
NOT “G” Key
“G” Key
Use 4D Key after market
or factory 08020 / 60160
Use dealer “G” key
If ALL KEYS LOST:
Use TYPE 4 Quick Reset
Immobilizer
If ALL KEYS LOST:
Use TYPE 5
Reset Immobilizer
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
559
M
M
VVPP && ADVANCED DIAGNOSTICS
powered
TOYOTA
PRIUS
‘04-’09USA
by
TCODE
TCODE
M V Ppowered
&
TCODE
powered
TOYOTA
ADVANCED
ADVANCED
DIAGNOSTICS
DIAGNOSTICS
USA
USA
by
by
General info
NEW “G” Transponder for 2010-2013 Toyota Keys
Toyota has released a new transponder chip for
2010 & up. This new TI chip has new “locked”
encryption to prevent cloning.
G
It has been seen in our experience that only
a Dealer Key will program reliably for these
vehicles!
There may be “after-market” versions
of these “G” keys available however at
this time we recommend using Toyota
only OEM keys.
Especially, if you are using MVP Pro
because “after-market” keys do not
always program in successfully.
From what we have seen, OEM keys
program successfully every time.
Special note for 2010 FJ Cruiser:
Some 2010 FJ Cruiser’s do not support an immobilizer reset.
On these affected vehicles the immo box must be replaced.
Affected vehicles where made BEFORE Vin #’s JTEZU4BF#AK010121 &
JTEBU4BF#AK088229. these vehicles will FAIL on Immo Reset attempt using PRO or
Dealer tools. This only effects FJ Cruiser and no other models.
560
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
powered
by
ADVANCED
ADVANCEDDIAGNOSTICS
DIAGNOSTICSUSA
USA
TOYOTA
PRIUS
‘04-’09
MVP &
TCODE
Toyota Immobilizer
TYPE 5 (G Key System)
ALL Toyota TYPE 5 use what the industry refers to as a “G” transponder chip in the keys.
Factory “G” chips can come in two varieties MASTER and VALET.
Factory keys with grey plastic heads have a VALET type & chip cannot be used to perform a
RESET or to introduce more keys into the system with the MVP or T-Code.
How to tell if a programmed key is a MASTER or a VALET?
Valet key- when first inserted into the ignition lock, the Security Light will stay on for 2 seconds and then stay off.
Master key- when inserted into the ignition lock, the Security Light will not illuminate at all.
TYPE 5 SPECIAL FUNCTIONS:
RESET Immobilizer: This function erases all keys and programs in 1 Master Key.
This function is used when the customer has lost all their Master keys. (Takes Approx.16
minutes)
PROGRAM KEY: This function allows you to add a Master or a Valet key to the car’s immobilizer system as long as you have an existing pre-programmed Master key to start with.
ERASE KEYS: This function allows you to erase all keys except the key in the ignition lock
at the time.
Program Master Key: This function is on the TYPE 5 menu for only one purpose. It is there
only for when for some reason a RESET Immobilizer procedure has been partially completed
but was for whatever reason (drivers door shut halfway thru or wrong transponder key used)
a Master Key was not programmed in successfully.
In cases like this the Immobilizer has already been Reset, so you need to be able to perform
this function separately because if you try and start off with Reset Immobilizer the procedure
will fail because the Immobilizer has already been Reset.
Program Master Key can only be used for this purpose. Do not use it unless you have the
situation described above.
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
561
M
M
VVPP && ADVANCED DIAGNOSTICS
powered
TOYOTA
PRIUS
‘04-’09USA
by
TCODE
TCODE
M V Ppowered
&
TCODE
powered
TOYOTA
ADVANCED
ADVANCED
DIAGNOSTICS
DIAGNOSTICS
USA
USA
by
by
TOYOTA 2011 - K E Y S
RESET Immobilizer - TYPE 5
(Use this method if you have no Master Keys.)
The procedure for 2010-2013 “G” Key system is very different from earlier TOYOTA LEXUS.
You cannot “Learn” (program) new keys as you did before by cycling the keys in the ignition.
After performing the “RESET
Immobilizer” procedure - remove the key from the ignition.
Insert the first key to be programmed when asked to do so by machine.
This must be a Master key, not a Valet (grey) key.
After the first Master key is “Learned”, each key must be
programmed separately.
For additional keys use the “PROGRAM KEYS” procedure.
p
?
t
q
VEHICLE SELECTION
+ BY SYSTEM
t
u
+ USA
p
?
?
562
q
u
VEHICLE SELECTION
t
p
q
+ Immobilizer
+ REMOTE
+ PROXIMITY
VEHICLE SELECTION
t
p
?
VEHICLE SELECTION
+ AUDI
+ LANDROVER
+ BMW
+ LEXUS
+ CADILLAC
+ MAZDA
+ CHEVROLET
+ MERCEDES
+ CHRYSLER
+ MITSUBISHI
+ DAEWOO USA
+ NISSAN
+ DODGE
+ PONTIAC
+ FORD
+ ROVER
+ GM (USA)
+ SAAB
+ HONDA/ACURA
+ SATURN
+ HYUNDAI
+ SUBARU
+ INFINITI
+ TOYOTA
+ ISUZU
+ V.W. /AUDI GROUP
+ JAGUAR
+ VOLKSWAGEN
+ JEEP
VERSION
+ KIA
q
u
u
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
Mpowered
V P & ADVANCED
TOYOTA USA
ADVANCEDDIAGNOSTICS
DIAGNOSTICS
USA
by
TCODE
TOYOTA
PRIUS
‘04-’09
ADVANCED
DIAGNOSTICS
USA
M V Ppowered
&
by
TCODE
TOYOTA 2011 - K E Y S
RESET Immobilizer - TYPE 5
Continued...
Use your
Smart Card and
avoid the Web
Security Access.
SMART CARD SECURITY
RESET Immobilizer
PLEASE INSURE THAT
THE DRIVER DOOR IS
OPEN DURING THE
PROCEDURE
ACCESS GRANTED
PRESS ENTER KEY
RESET Immobilizer
PRESS ENTER KEY
PLEASE WAIT
SWITCH IGNITION ON
TIME REQUIRED 16:00
TIME ELAPSED 00:00
BACK TO EXIT
PRESS ENTER KEY
RESET Immobilizer
PROCEDURE COMPLETE
DIAGNOSTIC MENU
TURN IGNITION OFF
REMOVE KEY
INSERT KEY
SWITCH IGNITION ON
> ECU IDENTIFICATION
> FAULT CODES
> ACTUATORS
> SPECIAL FUNCTIONS
PRESS ENTER KEY
DIAGNOSTIC MENU
>
>
>
>
PROGRAM KEYS
ERASE KEYS
RESET Immobilizer
SELF TEST
Continued on next
page....
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
563
M
M
VVPP && ADVANCED DIAGNOSTICS
powered
TOYOTA
PRIUS
‘04-’09USA
by
TCODE
TCODE
M V Ppowered
&
TCODE
powered
TOYOTA
ADVANCED
ADVANCED
DIAGNOSTICS
DIAGNOSTICS
USA
USA
by
by
TOYOTA 2011 - K E Y S
RESET Immobilizer - TYPE 5
continued...
PROGRAM KEY
PROGRAM KEY
INSERT MASTER KEY
SWITCH IGNITION ON
PROCEDURE COMPLETE
PRESS ENTER KEY
PRESS ENTER KEY
PROGRAM KEY
PLEASE WAIT
45 Sec
TIME ELAPSED: 0
IMPORTANT: Make sure to wait until
the theft light on the car stops blinking
and also press Enter before disconnecting the tester.
IMPORTANT NOTES:
On Toyota Type 5 it’s important to make sure the immobilizer light stops blinking at the end of the procedure.
It’s also important to Press Enter prior to disconnecting the tester.
Make sure to wait until the light stops blinking and also press Enter before disconnecting the tester.
If you are using MVP, stay connected and go to PROGRAM KEYS to add any additional keys you may have.
(If needed)
564
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
Mpowered
V P & ADVANCED
TOYOTA USA
ADVANCEDDIAGNOSTICS
DIAGNOSTICS
USA
by
TCODE
TOYOTA
PRIUS
‘04-’09
ADVANCED
DIAGNOSTICS
USA
M V Ppowered
&
by
TCODE
PROGRAM KEYS - TYPE 5
(Use this method if you have at least 1 Master Key.)
NOTE: If you do not have an existing Master key you must use the “Reset Immobilizer” procedure to Reset
the Immobilizer system. A Valet key will not work as a substitute for a Master Key.
p
?
t
q
u
VEHICLE SELECTION
TYPE 1
TYPE 2
TYPE 3
TYPE 4
TYPE 5
t
p
?
VEHICLE SELECTION
+ AUDI
+ LANDROVER
+ BMW
+ LEXUS
+ CADILLAC
+ MAZDA
+ CHEVROLET
+ MERCEDES
+ CHRYSLER
+ MITSUBISHI
+ DAEWOO USA
+ NISSAN
+ DODGE
+ PONTIAC
+ FORD
+ ROVER
+ GM (USA)
+ SAAB
+ HONDA/ACURA
+ SATURN
+ HYUNDAI
+ SUBARU
+ INFINITI
+ TOYOTA
+ ISUZU
+ V.W. /AUDI GROUP
+ JAGUAR
+ VOLKSWAGEN
+ JEEP
VERSION
+ KIA
q
u
Use your
Smart Card and
avoid the Web
Security Access.
VEHICLE SELECTION
+ USA
p
?
t
SWITCH IGNITION ON
q
PRESS ENTER KEY
u
VEHICLE SELECTION
Read the tester screens carefully! At this
step the key in the ignition must be an
already programmed Master Key.
+ BY SYSTEM
p
?
t
q
u
VEHICLE SELECTION
Continued on next
page....
+ Immobilizer
+ REMOTE
+ PROXIMITY
p
?
t
q
u
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
565
M
M
VVPP && ADVANCED DIAGNOSTICS
powered
TOYOTA
PRIUS
‘04-’09USA
by
TCODE
TCODE
M V Ppowered
&
TCODE
powered
TOYOTA
ADVANCED
ADVANCED
DIAGNOSTICS
DIAGNOSTICS
USA
USA
by
by
TOYOTA 2011 - K E Y S
PROGRAM KEYS - TYPE 5
Continued....
ECU IDENTIFICATION
PROGRAM KEY
TOYOTA KEY
SWITCH IGNITION OFF
REMOVE KEY
WITHIN 10 Sec
TIME ELAPSED: 0 S
PRESS ENTER KEY
PRESS ENTER KEY
DIAGNOSTIC MENU
> ECU IDENTIFICATION
> FAULT CODES
> ACTUATORS
> SPECIAL FUNCTIONS
DIAGNOSTIC MENU
>
>
>
>
PROGRAM KEYS
ERASE KEYS
RESET Immobilizer
SELF TEST
PROGRAM KEY
REMOVE KEY
INSERT KEY
SWITCH IGNITION ON
WITHIN 120 Sec
TIME ELAPSED: 0 S
PRESS ENTER KEY
566
PROGRAM KEY
INSERT NEW KEY
LEAVE IGNITION OFF
WITHIN 10 Sec
TIME ELAPSED: 0 S
PRESS ENTER KEY
VERY IMPORTANT:
Make sure to LEAVE IGNITION OFF here as instructed
by the tester. If you turn the key on here you will get
ERROR.
This is a very easy mistake to make.
READ THE TESTER SCREENS CAREFULLY!
PROGRAM KEY
PLEASE WAIT
TRYING TO COMMUNICATE
TIME ELAPSED: 0 S
PRESS ENTER KEY
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
M
V P & ADVANCED
powered
TOYOTA USA
ADVANCEDDIAGNOSTICS
DIAGNOSTICS
USA
by
TCODE
M V Ppowered
&
by
TCODE
TOYOTA
PRIUS
‘04-’09
ADVANCED
DIAGNOSTICS
USA
TOYOTA 2011 - K E Y S
PROGRAM KEYS - TYPE 5
Continued....
PROGRAM KEY
PROCEDURE COMPLETE
PRESS ENTER KEY
IMPORTANT: Make sure to wait until
the theft light on the car stops blinking
and also press Enter before disconnecting the tester.
IMPORTANT NOTES:
On this system it’s important to make sure the immobilizer light stops blinking at the end of the
procedure. It’s also important to Press Enter prior to disconnecting the tester.
Make sure to wait until the light stops blinking and also press Enter before disconnecting the
tester.
If you are using MVP, stay connected and go to PROGRAM KEYS to add any additional keys you
may have. (If needed)
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
567
M
M
VVPP && ADVANCED DIAGNOSTICS
powered
TOYOTA
PRIUS
‘04-’09USA
by
TCODE
TCODE
M V Ppowered
&
TCODE
powered
TOYOTA
ADVANCED
ADVANCED
DIAGNOSTICS
DIAGNOSTICS
USA
USA
by
by
TOYOTA 2011 - R E MO T E S
PROGRAM REMOTE - TYPE 4
(Use this method to program the Remote portion of remote head keys
on G KEY System Toyota’s)
Even though the transponder programs with Immo TYPE 5 we use TYPE 4
on the Remotes Menu for the Remote Programming.
The RKE program separate from
the transponder on TOYOTA G
chip remote head keys.
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
ECU IDENTIFICATION
TOYOTA TYPE 4
PRESS ENTER KEY
DIAGNOSTIC MENU
VEHICLE SELECTION
Immobilizer
> REMOTE
PROXIMITY
VEHICLE SELECTION
TYPE 1
TYPE 2
TYPE 3
> TYPE 4
SWITCH IGNITION ON
PRESS ENTER KEY
568
ECU IDENTIFICATION
> SPECIAL FUNCTIONS
DIAGNOSTIC MENU
ERASE REMOTES
> PROGRAM REMOTE
Be careful when programming remote head
keys there are several different FCC ID’s for the
remote components. They are not interchangeable and must be correct for the vehicle you are
working on.
A prudent tip for doing these is to
Program in the remote portion BEFORE cutting
the blade. Use another key or a metal work key
to turn the ignition ON during the procedure.
PROGRAM REMOTE
PRESS LOCK & UNLOCK
TOGETHER FOR 4 Sec.
PRESS UNLOCK BUTTON
FOR 1 SEC
BACK’ TO EXIT
Note: Press the Lock & Unlock
buttons together for 4 seconds
and quickly press Unlock button
for 1 second. You must be fast
on the button operation.
PRESS the BACK BUTTON to COMPLETE THE
PROGRAMMING.
PROGRAM REMOTE
PROGRAM REMOTE
SYSTEM WILL BEEP
WHEN COMPLETE
PROCEDURE COMPLETE
PRESS ENTER KEY
PRESS ENTER KEY
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
Mpowered
V P & ADVANCED
TOYOTA USA
ADVANCEDDIAGNOSTICS
DIAGNOSTICS
USA
by
TCODE
TOYOTA
PRIUS
‘04-’09
ADVANCED
DIAGNOSTICS
USA
M V Ppowered
&
by
TCODE
TOYOTA 2011 - P R O X
Types of TOYOTA PROX in Use for 2010 / 11
2010-2011 Toyota PRIUS Prox Remotes
NEW Optional Proximity Transponder for 2011 Sienna Van
Used Toyota/Lexus Proximity key warning!
Prox keys that are not BRAND NEW cannot be simply ADDED.
There is a work around trick that will usually allow you to program in an already used Prox.
1. Perform an Immobilizer reset introducing the used key first.
2. Once you have the used key programmed and working use PROGRAM PROX
to add back in the original working Prox key(s).
MVP users take note: The above method may not always work 100%.
Brand new keys from a reputable dealer is what we recommend.
These program in 100% without issue.
Cross Interference:
It has been our experience that on occasion there can be cross signal interference when 2 or more Prox remotes are in the
vehicle at the same time. During Programming keep only one Prox remote in the car at a time because of this.
Weak Prox Batteries:
Also, when using NEW Prox remotes if they get a failure it can be because the battery in the Prox is slightly weak from
sitting around in the parts dept. and may not program in until the Prox battery is changed.
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
569
M
M
VVPP && ADVANCED DIAGNOSTICS
powered
TOYOTA
PRIUS
‘04-’09USA
by
TCODE
TCODE
M V Ppowered
&
TCODE
powered
TOYOTA
ADVANCED
ADVANCED
DIAGNOSTICS
DIAGNOSTICS
USA
USA
by
by
TOYOTA 2011 - P R O X
RESET Immobilizer - TYPE 6
(Use this method if you have no Prox Remotes)
p
?
t
q
u
VEHICLE SELECTION
TYPE 3
TYPE 4
TYPE 5
TYPE 6
t
p
?
VEHICLE SELECTION
+ AUDI
+ LANDROVER
+ BMW
+ LEXUS
+ CADILLAC
+ MAZDA
+ CHEVROLET
+ MERCEDES
+ CHRYSLER
+ MITSUBISHI
+ DAEWOO USA
+ NISSAN
+ DODGE
+ PONTIAC
+ FORD
+ ROVER
+ GM (USA)
+ SAAB
+ HONDA/ACURA
+ SATURN
+ HYUNDAI
+ SUBARU
+ INFINITI
+ TOYOTA
+ ISUZU
+ V.W. /AUDI GROUP
+ JAGUAR
+ VOLKSWAGEN
+ JEEP
VERSION
+ KIA
q
u
Now you will need to use your Smart Card to
continue. If you do not have the Smart Card
system then you will need to use WEB Security
to gain access and continue.
VEHICLE SELECTION
SMART CARD SECURITY
+ USA
ACCESS GRANTED
p
?
t
q
u
PRESS ENTER KEY
VEHICLE SELECTION
+ BY SYSTEM
p
?
t
SWITCH IGNITION ON
q
u
PRESS ENTER KEY
VEHICLE SELECTION
+ Immobilizer
+ REMOTE
+ PROXIMITY
570
p
?
t
IGNORE this message:
q
u
The Ignition DOES NOT have to be
turned “ON”
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
Mpowered
V P & ADVANCED
TOYOTA USA
ADVANCEDDIAGNOSTICS
DIAGNOSTICS
USA
by
TCODE
TOYOTA
PRIUS
‘04-’09
ADVANCED
DIAGNOSTICS
USA
M V Ppowered
&
by
TCODE
TOYOTA 2011 - P R O X
RESET Immobilizer - TYPE 6
Continued....
DIAGNOSTIC MENU
> ECU IDENTIFICATION
> FAULT CODES
> ACTUATORS
> SPECIAL FUNCTIONS
RESET Immobilizer
PLEASE WAIT
TIME REQUIRED 16:00
TIME ELAPSED 00:00
BACK TO EXIT
DIAGNOSTIC MENU
>
>
>
>
>
PROGRAM KEYS
ERASE KEYS
RESET Immobilizer
ID REG ENG START
ID REG SMART BOX
RESET Immobilizer
PROCEDURE COMPLETE
PRESS ENTER KEY
RESET Immobilizer
PLEASE INSURE THAT
THE DRIVER DOOR IS
OPEN DURING THE
PROCEDURE
PRESS ENTER KEY
After performing the “RESET
Immobilizer” procedure Each Prox must be programed
Separately.
Use the “PROGRAM KEYS” to
program your first key (Prox).
Make sure the car’s battery remains at or above
12 volts and the drivers door stays open during
the 16 minute RESET Procedure.
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
571
M
M
VVPP && ADVANCED DIAGNOSTICS
powered
TOYOTA
PRIUS
‘04-’09 USA
by
TCODE
TCODE
M V Ppowered
&
TCODE
powered
TOYOTA
ADVANCED
ADVANCED
DIAGNOSTICS
DIAGNOSTICS
USA
USA
by
by
TOYOTA 2011 - P R O X
PROGRAM PROX - TYPE 6
(Use this method if you have at least 1 Prox Remote)
NOTE: If you do not have an existing Prox Remotes you must use the “Reset Immobilizer” procedure to
Reset the Immobilizer system.
p
?
t
q
u
VEHICLE SELECTION
+ Immobilizer
+ REMOTE
+ PROXIMITY
t
q
u
VEHICLE SELECTION
TYPE 3
TYPE 4
TYPE 5
TYPE 6
p
?
t
VEHICLE SELECTION
p
?
VEHICLE SELECTION
+ AUDI
+ LANDROVER
+ BMW
+ LEXUS
+ CADILLAC
+ MAZDA
+ CHEVROLET
+ MERCEDES
+ CHRYSLER
+ MITSUBISHI
+ DAEWOO USA
+ NISSAN
+ DODGE
+ PONTIAC
+ FORD
+ ROVER
+ GM (USA)
+ SAAB
+ HONDA/ACURA
+ SATURN
+ HYUNDAI
+ SUBARU
+ INFINITI
+ TOYOTA
+ ISUZU
+ V.W. /AUDI GROUP
+ JAGUAR
+ VOLKSWAGEN
+ JEEP
VERSION
+ KIA
q
u
+ USA
p
?
t
q
u
Now you will need to use your Smart Card to
continue. If you do not have the Smart Card
system then you will need to use WEB Security
to gain access and continue.
VEHICLE SELECTION
SMART CARD SECURITY
+ BY SYSTEM
ACCESS GRANTED
p
?
t
q
u
PRESS ENTER KEY
572
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
Mpowered
V P & ADVANCED
TOYOTA USA
ADVANCEDDIAGNOSTICS
DIAGNOSTICS
USA
by
TCODE
TOYOTA
PRIUS
‘04-’09
ADVANCED
DIAGNOSTICS
USA
M V Ppowered
&
by
TCODE
PROGRAM PROX - TYPE 6
Continued....
PROGRAM KEYS
KEY DETECTED
REMOVE KEY
SWITCH IGNITION ON
TIME XX
PRESS ENTER KEY
DIAGNOSTIC MENU
> ECU IDENTIFICATION
> FAULT CODES
> ACTUATORS
> SPECIAL FUNCTIONS
PROGRAM KEYS
TOUCH ENGINE SW
WITH EMBLEM SIDE
OF NEXT NEW KEY
TIME XX
PRESS ENTER TO CONT.
DIAGNOSTIC MENU
>
>
>
>
>
PROGRAM KEYS
ERASE KEYS
RESET Immobilizer
ID REG ENG START
ID REG SMART BOX
If the Prox is not detected:
1. Check that it’s the correct part number. (Many look
a like but are incompatible)
2. That the battery inside the Prox is new.
3. That the battery voltage on the vehicle is at least 12
volts.
PROGRAM KEYS
PROGRAM KEYS
NUMBER OF KEYS
X ( 4 MAX )
PLEASE WAIT
BACK’ TO EXIT.
PRESS ENTER KEY
PROGRAM KEYS
PROGRAM KEYS
TOUCH ENGINE SW
WITH EMBLEM SIDE
OF REGISTERED KEY
TIME XX
BACK’ TO EXIT.
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
PROCEDURE COMPLETE
NUMBER OF KEYS X
PRESS ENTER KEY
573
MVP & TCODE - PRO
Powered by ADVANCED DIAGNOSTICS USA
2004-2009
Toyota Prius
Programming
“SPECIAL INSTRUCTIONS”
574
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
powered
by
ADVANCED DIAGNOSTICS USA
TOYOTA
MVP &
TCODE
Prius ‘04-’09 S pe ci al Instructi ons
CAUTION:
YOU MUST CONNECT TO THE
OBD2 PORT WITH THE
ORANGE DONGLE “M”
Necessary Steps to Successful Programming:
1)Must Have Orange Dongle “M”.
2)Must Have MVP Pro or TCODE Pro with ADS-150 software.
3)Read and Follow these Instructions.
4)There is no difference in the programming procedure for cars
with Smart Access Proximity and cars without.
5)Models that do not have Smart Access require the Remote Fob to be in the Learning Slot to start the car, always.
6)It is recommended to only use new Fobs. Fobs from other
cars and used Fobs from “who knows where” are not advised
because of problems programming them into the Wireless ECU.
7)The maximum number of programmed Fobs is 4.
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
575
Mpowered
V P & ADVANCED DIAGNOSTICS
TOYOTA USA
by
TCODE
PRIUS
‘04-’09
ADVANCED
DIAGNOSTICS
USA
M V Ppowered
&
by
TCODE
Prius ‘04-’09 Sp e ci al Instructi on s
Security Components
All Prius 2004-2009 models have a
Push Start Button on the dash.
The Proximity / Remote Fob
“Learning Slot” is located on the
right side of the driver’s dash.
On models without the “Smart
Access” feature installed the Prox
must be inserted into the slot for
the vehicle to be driven.
Dealer Part# 89070-47180
Black logo on back is for basic Prius
models and do not
have Smart Access Proximity.
Dealer Part# 89994-47061
Chrome logo on back is for
Smart Access
Proximity Prius models.
Smart Access Proximity Prius models have a Rubber Push
Button on the front door handles.
This makes it easy to tell by just looking at the car which FOB
to use.
The different Fobs shown above are NOT interchangeable.
Models with the Smart Access Proximity system have a
“Lock-Out” button on the bottom of the dash, below the steering
column.
Make sure the button is in the “Out” position (not depressed).
576
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
M
V P & ADVANCED DIAGNOSTICS
powered
PRIUS ‘04-’09USA
by
TCODE
powered
by
MVP &
TOYOTA
ADVANCED DIAGNOSTICS USA
TCODE
Prius ‘04-’09 S pe ci al Instructi on s
Programming Overview
Programming Fob keys on ‘04-’09 Prius is a TWO STEP procedure.
STEP #1- Program the Immobilizer so that the FOB starts the vehicle.
STEP #2- Program the wireless functions so that the RKE buttons on the FOB lock and unlock the vehicle and if it’s a Smart Access model, the Fob will allow the car to start without
inserting the fob in the slot.
TYPE 2 IMMOBILIZER SPECIAL FUNCTIONS:
QUICK RESET Immobilizer: (“NEW” Available on Type 2 Immobilizer)
This function allows you to erase all Fobs and to place the immobilizer in “Auto Learn Mode”
instantly without having to go thru the 16 or 30 minute security delay found on the older regular Reset. On Prius this function is used when the customer has lost all their Fobs and you
want to program 1 or 2 Keys.
RESET Immobilizer: (Old way of resetting with security delay, now replaced with QUICK
RESET).
This function allows you to erase all keys and to place the immobilizer in the “Auto Learn
Mode”. This function is used when the customer has lost all their Fobs and you want to program in more than 2 keys (up to 4 Max.)
NOTE: The quick reset can be used if
you only want to program in 1 or 2 Fobs.
However, on Prius the quick reset will only
allow TWO keys to be programmed.
PROGRAM KEY: This function allows you to add a Fob to the car’s immobilizer system as
long as you have an existing pre-programmed Fob to start with.
ERASE KEYS: This function allows you to erase all Fobs except the key in the ignition lock at
the time.
Note: These functions ONLY pertain to the cars immobilizer the RKE and or Prox functions
are completely separate. (Step #2)
The Security Theft
light is located in the
instrument cluster.
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
577
MVP & TCODE - PRO
Powered by ADVANCED DIAGNOSTICS USA
If you have no
existing programmed Fobs.
Follow the two step procedure
on the next page.
Used Prius Fob Key Warning!
Fob keys that are not BRAND NEW cannot be simply ADDED.
There is a work around trick that will usually allow you to program in an already used Prox.
1. Perform an Immobilizer reset introducing the used key first.
2. Once you have the used key programmed and working use PROGRAM PROX
to add back in the original working Prox key(s).
3. On 2004-2009 Prius a Proximity Type5 RESET ECU function must also be performed and the used Fob’s RKE added
in 1st, then any pre-exisitng keys added back in 2nd.
MVP users take note: The above method may not always work 100%.
Brand new keys from a reputable dealer is what we recommend.
These program in 100% without issue.
578
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
powered
by
MVP &
TCODE
TOYOTA
ADVANCED DIAGNOSTICS USA
Prius ‘04-’09 S p e ci al Instructi on s
STEP #1 if you have no Working Prox Fobs
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
DIAGNOSTIC MENU
RESET Immobilizer
PROGRAM KEY
ERASE KEYS
> QUICK RESET Immobilizer
WARNING! USE ONLY THE “M”
DONGLE!
QUICK RESET IMMOBILIZER
This will RESET the immobilizer and place
the system in “AUTO LEARN MODE”
within just seconds.
VEHICLE SELECTION
> Immobilizer
REMOTE
VEHICLE SELECTION
TYPE 1
> TYPE 2
TYPE 3
TYPE 4
TYPE 5
TRYING TO COMMUNICATE
RESET Immobilizer
PROCEDURE COMPLETE
RESET Immobilizer
OR
PRESS ENTER KEY
SWITCH IGNITION ON
IGNORE THIS STEP
PLACE A PROX IN THE
SLOT
PRESS ENTER KEY
ECU IDENTIFICATION
TOYOTA/LEXUS TYPE 2
PRESS ENTER KEY
DIAGNOSTIC MENU
ECU IDENTIFICATION
FAULT CODES
LIVE DATA
ACTUATORS
> SPECIAL FUNCTIONS
COMMUNICATION FAILED
PRESS ENTER KEY
Both are OK
WATCH THE SECURITY LIGHT!
Most of the time you will see PROCEDURE COMPLETE message on the tester.
However, sometimes the car does not signal the tester that the immobilizer has been
reset and you may see COMMUNICATION FAILED on the screen.
DO NOT WATCH THE TESTER,
WATCH THE CARS SECURITY LIGHT!
Auto Learn mode is indicated by the steady illumination of the Security Light.
Once you see a solid immo light. Insert each FOB you want to program into the learning
slot but do not turn the ignition ON - remove after 5 seconds. The vehicle may learn up to
2 Fobs keys before the Auto Learn cycle is shut down.
If you only want to program just 1 Fob You can close the cycle early by pressing
Start/Stop button On & OFF numerous times, very fast until the theft light goes out..
Remove the key and re-insert it and the Security Lite should be out when there is a
programmed key in the slot.
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
579
MVP &
TCODE
TOYOTA
ADVANCED DIAGNOSTICS USA
powered
by
Prius ‘04-’09 Sp e ci al Instructi on s
STEP #2 if you have no Working Prox Fobs
(Programs the Remote/Prox functions on the Prox)
IMPORTANT TRICK TO TURN THE CAR ON AND STILL HAVE THE PROX IN YOUR HANDS:
To program the wireless (RKE) we need to trick the car into thinking there is a Prox in slot so we can
turn on the vehicle without the Prox actually being in the slot.
The idea is to have the car turned ON but to have the Prox in your hands so you can easily push the
RKE buttons when necessary.
Here's how it's done; Put the Prox all the way in the slot, then step on the brake, pull the Prox out
just a bit (this is done using very little force) until you hear a click, then press the start button.
Now that the car is on (you should see the dash light up) and you can remove the Prox from the
slot.
Note-because we stepped on the brake and the car is ON the vehicle’s gas engine will come
on if the voltage gets near 12 Volts or less and so you don't have to worry about having low
power in the battery or using jumper cables because the car will charge itself.
VEHICLE SELECTION
You MUST connect to the OBD2 port
with Orange Dongle “M”
VEHICLE SELECTION
+ AUDI
+ LANDROVER
+ BMW
+ LEXUS
+ CADILLAC
+ MAZDA
+ CHEVROLET
+ MERCEDES
+ CHRYSLER
+ MITSUBISHI
+ DAEWOO USA
+ NISSAN
+ DODGE
+ PONTIAC
+ FORD
+ ROVER
+ GM (USA)
+ SAAB
+ HONDA/ACURA
+ SATURN
+ HYUNDAI
+ SUBARU
+ INFINITI
+ TOYOTA
+ ISUZU
+ V.W. /AUDI GROUP
+ JAGUAR
+ VOLKSWAGEN
+ JEEP
VERSION
+ KIA
580
p
?
t
q
u
+ USA
PRESS ENTER KEY
VEHICLE SELECTION
+ Immobilizer
+ REMOTE
+ PROXIMITY
PRESS ENTER KEY
VEHICLE SELECTION
TYPE 1
TYPE 2
TYPE 3
TYPE 4
TYPE 5
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
powered
by
ADVANCED DIAGNOSTICS USA
TOYOTA
MVP &
TCODE
Prius ‘04-’09 S p e ci al Instructi ons
STEP #2 Continued from previous page
Use your
Smart Card and
avoid the Web
Security Access.
Make sure that the vehicle is turned “ON”
See trick on the previous page to turn the
car ON without the Fob trapped in the
slot.
ECU IDENTIFICATION
TO Y O TA / LE X U S R E M O T E T Y PE3
PRESS ENTER KEY
RESET Immobilizer
PLEASE INSURE THAT
THE DRIVER DOOR IS OPEN DURING THE
PROCEDURE
PRESS ENTER KEY
Even though the screen above says
immobilizer we are actually resetting the
Prox and RKE functions here.
Make sure the drivers door does not
close during the following steps or the
procedure will fail.
PROGRAM KEYS
It’s normal for the ECU ID screen here to
read TYPE3 even though we are actually
selecting PROXIMITY TYPE5
PROCEDURE COMPLETE
PRESS ENTER KEY
DIAGNOSTIC MENU
ECU IDENTIFICATION
FAULT CODES
> SPECIAL FUNCTIONS
DIAGNOSTIC MENU
PROGRAM REMOTE
ERASE REMOTE
> RESET ECU
If the screen above comes up right away
without going thru the 16 min. reset time
this is a “glitch” in the software. Stay
connected and go back to the menu and
select RESET ECU again. The driver’s
door open warning screen should come
up and then the following screen should
be next.......
continued on next page >
RESET ECU will clear all programmed
Prox’s from memory
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
581
MVP &
TCODE
TOYOTA
ADVANCED DIAGNOSTICS USA
powered
by
Prius ‘04-’09 Sp e ci al Instructi on s
RESET Immobilizer
PROGRAM KEYS
PLEASE WAIT
KEYS PROGRAMMED
KEYS 0
TIME REQUIRED 16:00
BACK TO EXIT
PRESS ENTER KEY
The screen above will not count down or
change but should change automatically
after the 16minutes elapses to display
PROCEDURE COMPLETE.
The ECU RESET was completed successfully if KEYS PROGRAMMED now
reads zero (as shown above).
PROGRAM KEYS
WITH NEW KEY
PRESS LOCK & UNLOCK
TOGETHER FOR 1 Sec.
PROGRAM KEYS
PRESS LOCK BUTTON
PROCEDURE COMPLETE
PRESS ENTER KEY
PRESS ENTER KEY
Press & hold the lock button on the Fob
until you hear faint beep from the car.
DIAGNOSTIC MENU
KEYS PROGRAMMED
KEYS 1
> PROGRAM REMOTE
ERASE REMOTE
RESET ECU
PRESS ENTER KEY
PROGRAM KEYS
PROGRAM KEYS
SWITCH IGNITION ON
PROCEDURE COMPLETE
PRESS ENTER KEY
PRESS ENTER KEY
The ignition should still be ON so just
leave it that way here....
582
You should be all done with completely
programming ONE key at this point.
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
MVP & TCODE - PRO
Powered by ADVANCED DIAGNOSTICS USA
If you have 1 or more
existing programmed Fobs.
Follow the procedure on the
next page.
Used Prius Fob Key Warning!
Fob keys that are not BRAND NEW cannot be simply ADDED.
There is a work around trick that will usually allow you to program in an already used Prox.
1. Perform an Immobilizer reset introducing the used key first.
2. Once you have the used key programmed and working use PROGRAM PROX
to add back in the original working Prox key(s).
3. On 2004-2009 Prius a Proximity Type5 RESET ECU function must also be performed and the used Fob’s RKE added
in 1st, then any pre-exisitng keys added back in 2nd.
MVP users take note: The above method may not always work 100%.
Brand new keys from a reputable dealer is what we recommend.
These program in 100% without issue.
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
583
MVP &
TCODE
TOYOTA
ADVANCED DIAGNOSTICS USA
powered
by
Step 1 - If you have 1 or more existing Fobs
Program Immobilizer - Type 2
You MUST connect to the OBD2 port
with Orange Dongle “M”
VEHICLE SELECTION
+ AUDI
+ LANDROVER
+ BMW
+ LEXUS
+ CADILLAC
+ MAZDA
+ CHEVROLET
+ MERCEDES
+ CHRYSLER
+ MITSUBISHI
+ DAEWOO USA
+ NISSAN
+ DODGE
+ PONTIAC
+ FORD
+ ROVER
+ GM (USA)
+ SAAB
+ HONDA/ACURA
+ SATURN
+ HYUNDAI
+ SUBARU
+ INFINITI
+ TOYOTA
+ ISUZU
+ V.W. /AUDI GROUP
+ JAGUAR
+ VOLKSWAGEN
+ JEEP
VERSION
+ KIA
p
?
t
q
u
VEHICLE SELECTION
VEHICLE SELECTION
+ Immobilizer
+ REMOTE
+ PROXIMITY
PRESS ENTER KEY
VEHICLE SELECTION
TYPE 1
TYPE 2
TYPE 3
TYPE 4
PRESS ENTER KEY
ECU IDENTIFICATION
TOYOTA/LEXUS TYPE 2
PRESS ENTER KEY
+ USA
DIAGNOSTIC MENU
PRESS ENTER KEY
You will be prompted to “Turn the Ignition
Switch On”. Make sure there is a existing
already programmed Remote Fob in the
Learning Slot. Press the Start button to
turn on the dash lights in the instrument
cluster.
584
ECU IDENTIFICATION
FAULT CODES
LIVE DATA
ACTUATORS
> SPECIAL FUNCTIONS
DIAGNOSTIC MENU
RESET Immobilizer
> PROGRAM KEYS
ERASE KEYS
QUICK RESET Immobilizer.
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
powered
by
TOYOTA
ADVANCED DIAGNOSTICS USA
Program Immobilizer - Type 2
PROGRAM KEYS
continued...
PROGRAM KEYS
SWITCH IGNITION OFF
REMOVE KEY
INSERT SAME KEY
SWITCH IGNITION ON
WITHIN 120 Sec
TIME ELAPSED: 0 S
PRESS ENTER KEY
Press the Start button to turn off the car
and remove the Fob. Re-insert the Fob
and press the Start button to turn on the
dash lights in the instrument cluster.
PROGRAM KEYS
SWITCH IGNITION OFF
REMOVE KEY
WITHIN 20 Sec
TIME ELAPSED: 0 S
PRESS ENTER KEY
Press the Start button to turn off the car
and remove the Fob. Insert the new Fob
to be programmed and do not press the
Start button.
MVP &
TCODE
PLEASE WAIT
Note: This usually takes about 60 sec.
PROGRAM KEYS
PROCEDURE COMPLETE
PRESS ENTER KEY
The Security Theft light on the dash
should be out and the first step of programming your new Fob is done. It is
time now to continue to the next step.
Use the Back button on the Pro to get
back to the Proximity menu.
PROGRAM KEYS
INSERT NEW KEY
LEAVE IGNITION OFF
WITHIN 10 Sec
TIME ELAPSED: 0 S
PRESS ENTER KEY
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
585
MVP &
TCODE
TOYOTA
ADVANCED DIAGNOSTICS USA
Program RKE / PROX - Type 5
powered
by
continued...
Now that the immobilzer has been programmed, proceed to programming the wireless &
or RKE functions of the Prox remote or remotes you want to program. This can be done
with the tool or using the On-Board procedure detailed later in this section.
You MUST connect to the OBD2 port
with Orange Dongle “M”
VEHICLE SELECTION
+ AUDI
+ LANDROVER
+ BMW
+ LEXUS
+ CADILLAC
+ MAZDA
+ CHEVROLET
+ MERCEDES
+ CHRYSLER
+ MITSUBISHI
+ DAEWOO USA
+ NISSAN
+ DODGE
+ PONTIAC
+ FORD
+ ROVER
+ GM (USA)
+ SAAB
+ HONDA/ACURA
+ SATURN
+ HYUNDAI
+ SUBARU
+ INFINITI
+ TOYOTA
+ ISUZU
+ V.W. /AUDI GROUP
+ JAGUAR
+ VOLKSWAGEN
+ JEEP
VERSION
+ KIA
p
?
t
q
VEHICLE SELECTION
+ USA
PRESS ENTER KEY
586
u
VEHICLE SELECTION
+ Immobilizer
+ REMOTE
+ PROXIMITY
PRESS ENTER KEY
VEHICLE SELECTION
TYPE 1
TYPE 2
TYPE 3
TYPE 4
TYPE 5
Use your
Smart Card and
avoid the Web
Security Access.
Make sure that the vehicle is turned “ON”
See trick on Page TOYOTA 48. to turn
the car ON without the Fob trapped in the
slot.
You want the car ON and both Fobs old
and new in your hands.
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
powered
by
ADVANCED DIAGNOSTICS USA
TOYOTA
Program RKE / PROX - Type 5
continued...
PROGRAM KEYS
ECU IDENTIFICATION
WITH NEW KEY
PRESS LOCK & UNLOCK
TOGETHER FOR 1 Sec.
TO Y O TA / LE X U S R E M O T E T Y P E3
PRESS ENTER KEY
It’s normal for the ECU ID screen here to
read TYPE3 even though we are actually
selecting PROXIMITY TYPE5
DIAGNOSTIC MENU
ECU IDENTIFICATION
FAULT CODES
> SPECIAL FUNCTIONS
MVP &
TCODE
PRESS LOCK BUTTON
PRESS ENTER KEY
Hold the Prox up in the general area
around the center of the steering wheel
when pressing the buttons.
Registration may take up to 5 seconds.
Pressing “unlock again or any other buttons may cause the procedure to fail.
KEYS PROGRAMMED
KEYS X
DIAGNOSTIC MENU
> PROGRAM REMOTE
ERASE REMOTE
RESET ECU
PROGRAM KEYS
PRESS ENTER KEY
PROGRAM KEYS
PROCEDURE COMPLETE
KEYS PROGRAMMED
KEYS X
PRESS ENTER KEY
PRESS ENTER KEY
You should be all done at this point.
PROGRAM KEYS
WITH ORIGINAL KEY
PRESS THE LOCK BUTTON
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
587
MVP &
TCODE
TOYOTA
ADVANCED DIAGNOSTICS USA
powered
by
Alternative - On-Board Programming
for Prox and RKE functions
Included here as a courtesy,
Not supported by Tech Support.
Step 1- It's very important to make sure all the doors are closed except the
drivers door, that remains open.
Step 2- insert the Prox in and out of the slot twice.
Step 3- close drivers door twice, then leave it open.
Step 4- insert the Prox in slot once and pull it out.
Step 5- close the drivers door twice, then leave it open.
Step 6- insert the Prox in the slot & leave it in.
Step 7- close the drivers door once.
Step 8- turn the ignition on once, then turn it off.
Step 9- take the Prox out of the slot and the door locks should cycle.
Step 10- Next press the lock & unlock buttons together on the Prox for 1 second. Then press the lock button for 3 seconds.
Step 11- locks should cycle.
Step 12-To exit the learning mode open the door & close it.
Now open it again.
You are done! Now test your Prox key functions to be sure they work.
588
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
powered
by
ADVANCED DIAGNOSTICS USA
TOYOTA
MVP &
TCODE
Prius ‘04-’09 Trouble Shooting
Common Problems with Programming Fobs into Prius models:
• Used or worn out Fob -
a Check the status of the Fob trying to be programmed. • Is it new? • Was it from
another car? • Has it stopped working and now the customer wants it programmed
again? • There is a battery in it that might need replacing. • Some just wear out and
must be replaced with a new one. Brand new remote’s will always program, unless
of course, there is something actually wrong with the car.
• Either one of the 2 steps did not complete successfully. a Have you checked to see whether the fobs were programmed into the
immobilizer system. The Security Theft is out when there is a Fob in the Learning
Slot? It may be necessary to close the immobilizer cycle manually. Put a already
programmed Fob in the Learning Slot and press the Start button 5 times ON and
Off. This should close the cycle manually. • Remember the car can hold only 4 Fobs
into memory, it may be necessary to erase if you are trying to only Add a Fob into
memory.
NOTE: Quick reset Immobilizer on Prius will only allow TWO keys
to be programmed.
Use a Regular Reset if all keys are lost and you want to program
more than 2 keys.
• The Smart Access Fobs have programmed successfully but the car does unlock when I try from the outside.
a The “Lock Out” switch (under the steering column) has been depressed and is in
Lock Out mode.
• The Smart Access Fobs have programmed successfully but the car
will not Start unless I insert the Fob into the Learning Slot.
a Check the “Lock Out” switch (under the steering column) and see if it has been depressed and is in Lock Out mode. Next, does the car actually have Smart Access?
If there are no Rubber Push Buttons on the front outside door handles - there is no
Smart Access on this car. Therefore there is no Proximity system, just a simple
wireless system to lock and unlock the doors. You must insert the Fob into the
Learning Slot to Start and drive the car.
• The ABS & VSC light stays on or Flashes and the car will not move.
a Follow the procedure on the next page to reset the ABS dash lights. This is
triggered when not using the correct dongle while the Pro is connected to the car.
Programming using the M dongle will NOT cause this problem.
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
589
Mpowered
V P & ADVANCED DIAGNOSTICS
TOYOTA USA
by
TCODE
PRIUS
‘04-’09
ADVANCED
DIAGNOSTICS
USA
M V Ppowered
&
by
TCODE
Resetting the ABS Dash Lights
ABS & VSC lights are triggered when not using the correct
dongle while the Pro is connected to the car.
Do not press the brake pedal during this
procedure.
You MUST connect to the OBD2 port
with Orange Dongle “M”
DIAGNOSTIC MENU
> RESET ABS VSC LIGHT
Select on the PRO:
Toyota>USA>
VEHICLE SELECTION
RESET ABS VSC LIGHT
ABS AND VSC LIGHTS
WILL FLASH
+ USA
PRESS ENTER KEY
VEHICLE SELECTION
RESET ABS VSC LIGHT
PLEASE WAIT
THIS WILL
TAKE 3 MINUTES
DO NOT TOUCH BRAKE
XX m XXs
+ Immobilizer
+ REMOTE
+ PROXIMITY
ABS / VCS
PRESS ENTER KEY
Use your
Smart Card and
avoid the Web
Security Access.
RESET ABS VSC LIGHT
The car must remain in the Off position.
Do not press the Start button.
DIAGNOSTIC MENU
ECU IDENTIFICATION
> SPECIAL FUNCTIONS
590
PROCEDURE COMPLETE
ABS AND VSC LIGHTS
SHOULD NOT BE
FLASHING
RESET ABS VSC LIGHT
DISCONNECT TESTER
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
powered
by
ADVANCED DIAGNOSTICS USA
TOYOTA
MVP &
TCODE
NEW “H” Transponder for 2010-2013 Toyota Keys
Toyota has released a new transponder chip for
2013 Rav-4 & 2014 Corolla. This new chip has
80-Bit encryption to prevent cloning.
The new key can be easily identified by the H
stamped on the blade
“H” KEY SYSTEMS
Program using:
TOYOTA IMMO TYPE 6
Just like on earlier Toyota systems factory keys with grey plastic heads are VALET keys &
cannot be used to perform a RESET or to introduce more keys into the system with the MVP
or T-Code.
How to tell if a programmed key is a MASTER or a VALET?
Valet key- when first inserted into the ignition lock, the Security Light will stay on for 2 seconds and then stay off.
Master key- when inserted into the ignition lock, the Security Light will not illuminate at all.
TYPE 6 SPECIAL FUNCTIONS:
RESET Immobilizer: This function erases all keys and programs in 1 Master Key.
This function is used when the customer has lost all their Master keys. (Takes Approx.16
minutes)
PROGRAM KEY: This function allows you to add a Master or a Valet key to the car’s immobilizer system as long as you have an existing pre-programmed Master key to start with.
ERASE KEYS: This function allows you to erase all keys except the key in the ignition lock
at the time.
Program Master Key: This function is on the TYPE 6 menu for only one purpose. It is there
only for when for some reason a RESET Immobilizer procedure has been partially completed
but was for whatever reason (drivers door shut halfway thru or wrong transponder key used)
a Master Key was not programmed in successfully.
In cases like this the Immobilizer has already been Reset, so you need to be able to perform
this function separately because if you try and start off with Reset Immobilizer the procedure
will fail because the Immobilizer has already been Reset.
Program Master Key can only be used for this purpose. Do not use it unless you have the
situation described above.
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
591
MVP &
TCODE
TOYOTA
ADVANCED DIAGNOSTICS USA
powered
by
RESET Immobilizer - TYPE 6
Use this method for
LOST KEYS when you have
no programmed Master Keys
avaliable.
SWITCH IGNITION ON
PRESS ENTER KEY
p
?
t
q
u
VEHICLE SELECTION
VEHICLE SELECTION
+ BY SYSTEM
t
p
?
VEHICLE SELECTION
+ AUDI
+ LANDROVER
+ BMW
+ LEXUS
+ CADILLAC
+ MAZDA
+ CHEVROLET
+ MERCEDES
+ CHRYSLER
+ MITSUBISHI
+ DAEWOO USA
+ NISSAN
+ DODGE
+ PONTIAC
+ FORD
+ ROVER
+ GM (USA)
+ SAAB
+ HONDA/ACURA
+ SATURN
+ HYUNDAI
+ SUBARU
+ INFINITI
+ TOYOTA
+ ISUZU
+ V.W. /AUDI GROUP
+ JAGUAR
+ VOLKSWAGEN
+ JEEP
VERSION
+ KIA
q
u
VEHICLE SELECTION
+ Immobilizer
+ REMOTE
+ PROXIMITY
p
?
t
+ USA
q
u
DIAGNOSTIC MENU
p
?
t
q
Use your
Smart Card and
avoid the Web
Security Access.
u
> ECU IDENTIFICATION
> FAULT CODES
> ACTUATORS
> SPECIAL FUNCTIONS
DIAGNOSTIC MENU
SMART CARD SECURITY
ACCESS GRANTED
>
>
>
>
PROGRAM KEYS
ERASE KEYS
RESET Immobilizer
SELF TEST
PRESS ENTER KEY
592
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
Mpowered
V P & ADVANCED DIAGNOSTICS
TOYOTA
USA
by
TCODE
TOYOTA
ADVANCED
DIAGNOSTICS USA
M V Ppowered
&
by
TCODE
RESET Immobilizer - TYPE 6
Continued...
RESET Immobilizer
PROGRAM KEY
PLEASE INSURE THAT
THE DRIVER DOOR IS
OPEN DURING THE
PROCEDURE
PLEASE WAIT
45 Sec
TIME ELAPSED: 0
PRESS ENTER KEY
RESET Immobilizer
PLEASE WAIT
PROGRAM KEY
PROCEDURE COMPLETE
TIME REQUIRED 16:00
TIME ELAPSED 00:00
BACK TO EXIT
PRESS ENTER KEY
RESET Immobilizer
PROCEDURE COMPLETE
TURN IGNITION OFF
REMOVE KEY
INSERT KEY
SWITCH IGNITION ON
PRESS ENTER KEY
PROGRAM KEY
INSERT MASTER KEY
SWITCH IGNITION ON
IMPORTANT NOTES:
On Toyota Type 636 it’s important to make sure
the immobilizer light stops blinking at the end of
the procedure. It’s also important to Press Enter
prior to disconnecting the tester.
Make sure to wait until the light stops blinking
and also press Enter before disconnecting the
tester.
If you are using MVP, stay connected and go to
PROGRAM KEYS to add any additional keys
you may have. (If needed)
PRESS ENTER KEY
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
593
MVP &
TCODE
TOYOTA
powered
by
ADVANCED DIAGNOSTICS USA
PROGRAM KEYS - TYPE 6
(Use this method if you have at least 1 Master Key.)
NOTE: If you do not have an existing Master key you must use the “Reset Immobilizer” procedure to Reset
the Immobilizer system. A Valet key will not work as a substitute for a Master Key.
p
?
t
q
u
VEHICLE SELECTION
TYPE 1
TYPE 2
TYPE 3
TYPE 4
TYPE 5
t
p
?
VEHICLE SELECTION
+ AUDI
+ LANDROVER
+ BMW
+ LEXUS
+ CADILLAC
+ MAZDA
+ CHEVROLET
+ MERCEDES
+ CHRYSLER
+ MITSUBISHI
+ DAEWOO USA
+ NISSAN
+ DODGE
+ PONTIAC
+ FORD
+ ROVER
+ GM (USA)
+ SAAB
+ HONDA/ACURA
+ SATURN
+ HYUNDAI
+ SUBARU
+ INFINITI
+ TOYOTA
+ ISUZU
+ V.W. /AUDI GROUP
+ JAGUAR
+ VOLKSWAGEN
+ JEEP
VERSION
+ KIA
q
u
Use your
Smart Card and
avoid the Web
Security Access.
VEHICLE SELECTION
+ USA
p
?
t
SWITCH IGNITION ON
q
u
PRESS ENTER KEY
VEHICLE SELECTION
Read the tester screens carefully! At this
step the key in the ignition must be an
already programmed Master Key.
+ BY SYSTEM
p
?
t
q
u
VEHICLE SELECTION
Continued on next
page....
+ Immobilizer
+ REMOTE
+ PROXIMITY
594
p
?
t
q
u
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
powered
by
TOYOTA
ADVANCED DIAGNOSTICS USA
MVP &
TCODE
PROGRAM KEYS - TYPE 6
Continued....
ECU IDENTIFICATION
PROGRAM KEY
TOYOTA KEY
SWITCH IGNITION OFF
REMOVE KEY
WITHIN 10 Sec
TIME ELAPSED: 0 S
PRESS ENTER KEY
PRESS ENTER KEY
DIAGNOSTIC MENU
> ECU IDENTIFICATION
> FAULT CODES
> ACTUATORS
> SPECIAL FUNCTIONS
DIAGNOSTIC MENU
>
>
>
>
PROGRAM KEYS
ERASE KEYS
RESET Immobilizer
SELF TEST
PROGRAM KEY
REMOVE KEY
INSERT KEY
SWITCH IGNITION ON
WITHIN 120 Sec
TIME ELAPSED: 0 S
PRESS ENTER KEY
PROGRAM KEY
INSERT NEW KEY
LEAVE IGNITION OFF
WITHIN 10 Sec
TIME ELAPSED: 0 S
PRESS ENTER KEY
VERY IMPORTANT:
Make sure to LEAVE IGNITION OFF here as instructed
by the tester. If you turn the key on here you will get
ERROR.
This is a very easy mistake to make.
READ THE TESTER SCREENS CAREFULLY!
PROGRAM KEY
PLEASE WAIT
TRYING TO COMMUNICATE
TIME ELAPSED: 0 S
PRESS ENTER KEY
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
595