FOR THE SCOPE OF
.
ACCREDITATION UNDER NVLAP LAB
CODE 100402-0.
.
REPORT
3933 US ROUTE 11, CORTLAND, NEW YORK 13045
Project No. G102418744
Date: February 5, 2016
REPORT NO. 102418744CRT-001
TEST OF ONE LINEAR LIGHT ENGINE
MODEL NO. LEL2316A30C
LED MODEL NO. SEOUL SAW9C72A MJT3030
DRIVER MODEL NO. MAGNACHIP MAP3012B
RENDERED TO:
MAXLITE, INC.
12 YORK AVE
WEST CALDWELL, NJ 07006-6411
TESTS:
Start Time, Transient Protection, Operating Frequency, Dimming, and Audible
Noise to the ENERGY STAR® Program Requirements for Luminaires Version
2.0
STATEMENT OF LIMITATION: This report must not be used by the client to claim product certification,
approval, or endorsement by NVLAP, NIST, or any agency of the federal
government.
AUTHORIZATION
The testing performed was authorized by signed quote number Qu-00665356.
STANDARDS USED:
ENERGY STAR® Program Requirements for Luminaires Version 2.0
ANSI/IEEE C62.41.2-2002 IEEE Recommended Practice on Characterization of Surges in Low-Voltage (1000V
and Less) AC Power Circuits
IESNA LM-79 - 2008: Electrical and Photometric Measurements of Solid State Lighting
DESCRIPTION OF SAMPLE:
The client submitted one production samples of model number LEL2316A30C.
The sample was received by Intertek on December 23, 2015 in undamaged
condition and one sample was tested as received. The sample designation was
CRT1512231341-001-1.
DATE OF TESTS:
January 27, 2016 through February 5, 2016
This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the
terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned
by the use of this report. Only the Client is authorized to copy or distribute this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or
advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested.
This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program.
SUMMARY:
MODEL NO. LEL2316A30C
DRIVER MODEL NO. MagnaChip MAP3012B
DESCRIPTION: Linear Light Engine
Criteria
Start Time (ms)
Transient Protection (# of strikes)
Operating Frequency at Max Dim (Hz)
Operating Frequency at Min Dim (Hz)
Dimming (%)
Maximum Audible Noise at 20% Dim (dBa)
Results
1.6
7
120
120
5.47
19.3
Status
Complies
Complies
Complies
Complies
Complies
Complies
EQUIPMENT LIST
Equipment Used
Extech Hygro-Thermometer
Tektronix Oscilliscope
UDT flexOptometer
Fluke Multimeter
Extech Hygro Thermometer
Keytek Wave Module
Keytek Coupler/Decoupler
Keytek Control Center
Digital Caliper
Sound Level Meter
SLM Microphone
RTD Pair
Barometer
Microphone Calibrator
Report No. 102418744CRT-001
Model No.
445715
DPO 2012
S490
87V
445715
E503
E551
E504
Fowler
2270
4189
Control No.
T1550
E480
O224
D590
T1550
W147
W148
W145
N1401
A350
A354
78N01N00N040B3 T1440/1
PTB110
P1063
4231
A227
2 of 7
Last Cal.
1/8/2016
11/18/2015
VBU
4/22/2015
1/8/2016
9/13/2015
9/13/2015
9/13/2015
7/31/2015
4/15/2015
4/15/2015
7/21/2015
7/20/2015
3/30/2015
Cal. Due
1/8/2017
11/18/2016
VBU
4/22/2016
1/8/2017
9/13/2016
9/13/2016
9/13/2016
7/31/2016
4/15/2016
4/15/2016
7/21/2016
7/20/2016
3/30/2016
Date: February 5, 2016
ENERGY STAR REQUIRMENTS:
CLASSIFICATION: DIRECTIONAL
CATEGORY: DOWNLIGHT, SSL RETROFIT KIT
SOURCE TYPE: SSL
Property
Source Start Time
(Outdoor exempt)
Requirements
Light source shall remain continuously illuminated within 750 milliseconds of
application of electrical power. Connected Luminaires shall remain continuously
illuminated within 750 milliseconds of application of electrical power.
≥ 1 samples of each ballast model, LED package, LED module or LED array and
LED driver model combination, or LED light engine shall be tested.
All samples shall pass.
Transient Protection
Survive 7 strikes of a 2.5kV, 100kHz Ringwave.
≥ 1 samples of each ballast model, LED package, LED module or LED array and
LED driver model combination, or LED light engine shall be tested.
All samples shall pass.
Operating Frequency#
Frequency ≥ 120 Hz
≥ 1 samples of each ballast model, LED package, LED module or LED array and
LED driver model combination, or LED light engine shall be tested.
The samples shall pass
Dimming and Audible
Noise#
The luminaire and its components shall provide continuous dimming from 100% to
20% of light output. Luminaire shall not emit noise above 24dBA at 1 meter or less
at the minimum output.
≥ 1 samples of each ballast model, LED package, LED module or LED array and
LED driver model combination, or LED light engine shall be tested.
The sample shall pass.
#Not NVLAP Accredited
Report No. 102418744CRT-001
3 of 7
Date: February 5, 2016
TEST METHODS:
Seasoning in Sample Orientation – LED Products
No seasoning was performed in accordance with IESNA LM-79.
Starting Delay Tests at Ambient Temperature (25°C + /- 1°C)
The starting delay tests at ambient temperature were performed on one sample. The oscilloscope was used to
measure the starting time. Each sample was operated at rated input voltage in its designated orientation during
the tests.
Transient Protection
The transient protection tests at ambient temperature were performed on one fixture sample. Each sample was
operated at rated input voltage in its designated orientation during the tests. A Model Keytek ECAT Surge Test
System with an 100kHz Ring Wave Module and a Coupler/Decoupler Module was used to generate the 2500 volt
ring wave transient strike across the lamp base contacts. Each wave consisted of a 0.5 microsecond rise time.
Seven strikes were performed on each sample in accordance with ANSI/IEEE C62.41 (Category A):
Recommended Practice on Surge Voltages in Low – Voltage AC Circuits.
Operating Frequency
Operating frequency was measured on one lamp sample with a photodetector, transimpedance amplifier, and
oscilloscope. Light output waveform measurements were recorded at the LED source. A digital graphic of the
amplitude was recorded. Operating frequency at dimming levels was also checked if applicable.
Dimming and Audible Noise
Dimming tests were performed on one sample with a photometer or oscilloscope. Each sample was allowed to
stabilize at its highest dimming point and a relative light output measurement was taken. The sample was then
dimmed to its lowest point without flickering and another relative light output measurement was taken. The
dimming range percentage was then calculated. Noise was conducted at 20% light output at a distance of 1
meter. Six different positions were measured, the maximum was recorded.
Report No. 102418744CRT-001
4 of 7
Date: February 5, 2016
RESULTS
Starting Delay Tests at Ambient Temperature (25°C + /- 1°C)
Intertek Fixture
Intertek Driver
Measured Start Time
Control No.
Control No.
(ms)
CRT1512231341-001-1 MagnaChip MAP3012B
1.6
Transient Protection
Intertek Fixture
Intertek Driver
Control No.
Control No.
CRT1512231341-001-1 MagnaChip MAP3012B
Number Of Strikes
Survived
7
Operating Frequency
Intertek Fixture
Intertek Driver
Control No.
Control No.
CRT1512231341-001-1 CRT1512231341-001-1
Maximum Dim (No Dim)
Operating Frequency
(Hz)
Minimum Dim
Operating Frequency
(Hz)
120
120
Operating Frequency (Hz) – Minimum Dimming
Operating Frequency (Hz) – Maximum Dimming
Report No. 102418744CRT-001
5 of 7
Date: February 5, 2016
RESULTS
Dimming
Intertek Fixture
Intertek Driver
Max Light Output Min Light Output
Control No.
(Lux)
Control No.
(Lux)
CRT1512231341-001-1 MagnaChip MAP3012B
19200
1050
Dimmer Used: Lutron: MAELV-600
Percent Dimmed
(%)
5.47
Audible Noise
Maximum Audible
Intertek Fixture
Intertek Driver
Noise (dBa)
Control No.
Control No.
CRT1512231341-001-1 MagnaChip MAP3012B
19.3
Dimmensions
Intertek Fixture
Control No.
CRT1512231341-001CRT1512231341-001CRT1512231341-001-
Model No.
LEL2316A30C
LEL11.5A0830C
LEL5.5A0530C
Report No. 102418744CRT-001
Measured
Maximum
Depth (In)
0.2235
0.2235
0.2235
6 of 7
Measured
Maximum
Overall
Length (In)
23.0
11.49
5.472
Measured
Maximum
Overall
Width (In)
1.494
1.499
1.49
Units
{mm}
{mm}
{mm}
Date: February 5, 2016
PRODUCT PICTURE:
Model No: LEL2316A30C
Model No: LEL11.5A0830C
Model No: LEL5.5A0530C
CONCLUSION
The results tabulated in this report are representative of the actual test samples submitted for this report only.
The data is provided to the client for further evaluation.
In Charge Of Tests:
Report Reviewed By:
John-Paul Mailhot
Engineer
Lighting Division
Jeffrey Davis
Engineering Supervisor
Lighting Division
Attachments: None
Report No. 102418744CRT-001
7 of 7
Date: February 5, 2016