12W Constant Current LED Driver (600mA) (12-22V)

advertisement
© futureeden
e
Product features:
ed
tu
©
re
fu
tu
ed
en
re
ed
en
12W Constant Current LED Driver
(600mA) (12-22V)
©
fu
tu
©
re
fu
• Universal input voltage(AC85-265V)
• The new PC plastic fireproof grade can reach V-1level
• 100% full load burn –in test, the product is stable and reliable. Temperature Resistance Tested -40°C to +75°C working temperature, but under the instantaneous 300V AC input up to 5 seconds
• Comply with safety regulations, electromagnetic compatibility (EMC)
• CE, CQC, SAA, PSE, CB and other domestic and international certification CE, CQC, SAA, PSE,
• Long life design warranty for 5 years (50000 hours)
• Built in two levels of lightning protection circuit design>2500V
• Applied in: decorative lighting, building lighting, stage lighting, ceiling light and spot light.
Rev 1.2 (10-02-16)
1
© futureeden
12W 600mA Constant Current (12-22v)
600mA
12-22V
RATED CURRENT
CONSTANT CURRENT
REGION Note.4
RATED POWER
RIPPLE & NOISE (max.)
Note.2
CURRENT TOLERANCE
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
ed
en
re
e
0.124A / 115VAC
0.06A / 230VAC
COLD START 40A at 230VAC
<0.75mA / 230VAC
95 ~ 105% Protection type : Constant current limiting, recovers automatically after fault condition is removed
Hiccup mode, recovers automatically after fault condition is removed
23 ~ 25V
Protection type : hiccup or when it is at the highest point of output
voltage the product would not be hurted when the fault is excluded or
is start working again the power supply is working normally
fu
©
©
OVER VOLTAGE
ed
THD
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INRUSH CURRENT(max.)
LEAKAGE CURRENT
OVER CURRENT (Typ.)
Note.4
SHORT CIRCUIT
PROTECTION
±5%
±5%
±5%
2000ms, 50ms at full load 230VAC /2500ms, 50ms at full load
115VAC,
20ms / 230VAC 16ms / 115VAC at full load
85 ~ 265VAC
47 ~ 63Hz
PF>0.98/115VAC, PF>0.95/230VAC,at full load (Please refer to "Power
Factor Characteristic" curve)
THD<20% (115VAC/230VAC)
84%
tu
INPUT
HOLD UP TIME (Typ.)
VOLTAGE RANGE Note.5
FREQUENCY RANGE
POWER FACTOR (Typ.)
fu
©
fu
OUTPUT
re
tu
12W
1000mVp-p
re
MODEL
tu
SPECIFICATION
ed
en
12W Constant Current LED Driver
(600mA) (12-22V)
Rev 1.2 (10-02-16)
2
© futureeden
-40 to +70°C (Refer to "Derating Curve")
20 ~ 95% RH non-condensing
-40 to +80°C, 10 to 95% RH
tu
SAFETY STANDARDS
Note.6
OTHERS
MTBF
DIMENSION
PACKING
e
tu
©
re
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
EMC EMISSION
EMC IMMUNITY
fu
SAFETY
&
EMC
±0.03%/°C (0~50°C)
10 ~ 500Hz, 5G 12min./1 cycle, period for 72min. each along X, Y, Z
axes
UL8750, CSA C22.2 No. 250.0-08, EN61347-1, EN61347-2-13
independent IP20, J61347-1, J61347-2-13 approved ; design refer to
UL60950-1, TUV EN60950-1
I/P-O/P:3.75KVAC
I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH
Compliance to EN55015,EN6100-3-2, ClassA, EN61000-3-3
Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, EN55024, light
industry level (surge 1KV), criteria A
831K hrs min. MIL-HDBK-217F (25°C)
97*36*22mm (L*W*H)
/
ed
en
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP,
HUMIDITY
TEMP. COEFFICIENT
VIBRATION
re
ENVIRONMENT
ed
en
12W Constant Current LED Driver
(600mA) (12-22V)
fu
©
NOTES
tu
©
re
fu
ed
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of
ambient temperature.在
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated
with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Constant current operation region is within 50% ~100% rated output voltage. This is the suitable
operation region for LED related applications.
5. Derating may be needed under low input voltages. Please check the for more details.
6. Safety and EMC design refer to EN60598-1, CNS15233, CNS15233, GB7000.1, FCC part18.
7. The power supply is considered as a component that will be operated in combination with
final equipment. Since EMC performance will be affected by the complete installation, the final
equipment manufacturers must re-qualify EMC Directive on the complete installation again.
Rev 1.2 (10-02-16)
3
© futureeden
ed
en
12W Constant Current LED Driver
(600mA) (12-22V)
DIMENSIONS
e
ed
tu
O.L.P
re
RECTIFIER
&
FILTER
+V
-V
fu
POWER
SWITCHING
tu
EMIFILTER
&
RECTIFIERS
PWM & PFC
CONTROL
©
I/P
©
BLOCK DIAGRAM
fu
©
22mm
re
fu
tu
36mm
ed
en
re
97mm
Rev 1.2 (10-02-16)
DETECTION
CIRCUIT
O.V.P
4
© futureeden
ed
en
12W Constant Current LED Driver
(600mA) (12-22V)
DERATING CURVE
STATIC CHARACTERISTICS
100
0
15
30
50
60
Ambient Temperature
100 125 135 145 155 165 175 180 200 230 264
re
0.88
90
230Vac
115Vac
0.86
©
tu
0.84
0.82
0.78
50%
60%
70%
fu
0.80
80%
LOAD
90%
100%
©
PF
0.90
40
fu
0.96
0.92
75
ed
0.98
0.94
70
tu
©
POWER FACTOR CHARACTERISTICS
1.00
50
Input Voltage (v) 60 hz
fu
-40 -25 -10
60
e
tu
20
70
re
40
80
ed
en
60
Load (%)
90
80
re
Load (%)
100
Rev 1.2 (10-02-16)
5
© futureeden
ed
en
12W Constant Current LED Driver
(600mA) (12-22V)
94
92
90
84
82
80
78
ed
en
re
86
tu
Efficiency (%)
88
76
74
230Vac
115Vac
fu
72
50%
60%
70%
80%
Load
90%
100%
tu
©
68
re
70
©
tu
Constant Current Area
fu
vo(%)
100
re
fu
LED (CC) LED(B)
ed
DRIVING METHODS OF LED MODULE LED
This LED power supply is suggested to work in constant current mode area (CC) to drive the LEDs.
e
EFFICIENCY VS LOAD
50
50
©
Hiccup Protection
100
lo (%)
LED l -V
Rev 1.2 (10-02-16)
6
Download