Interworks EQ®
Assembly Instructions
2041398 Revision C-11
Complete Series Master Packet
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
© 2011 Kimball International, Inc. T 800.482.1818
F 812.482.8300
System Assembly Instructions
Interworks® EQ
Page 1 of 1
Wall-Mount Connector
Tools Required
Tape Measure, Level, Wall Fasteners, Fastener Tools, two Panel Hinges (same height as Wall Mount), In-line Fill Cap for gap between
Top Cap and Wall-Mount Connector
Installation
These instructions apply to installation of an Interworks Panel perpendicular to an existing wall. Wall fasteners are Installer’s responsibility,
see below for fasteners specifications; Kimball does not assume responsibility for their use. To avoid leveling problems, identify high
point of floor; adjust panel height to accommodate for the high point of the floor.
Step 1
Step 2
Fasten Wall-Mount Connector
• Level panel and put perpendicular to wall
• Mark wall at top of side rail
• Remove panel
• Put wall-mount connector against wall mark, bottom should be at least 37⁄16"
above floor
Note: Fasteners are Installer’s responsibility.
• Tack wall-mount
connector through
top hole
Mark of Panel Side Rail Top
• Level wall-mount
Wall-Mount
connector vertically
Connector
• Mark holes for
fasteners at top,
middle, and bottom
• Attach to wall with
appropriate fasteners
Attach Panel
• Remove panel top cap
• Put panel against wall-mount connector
• Make sure top of wall-mount connector and side rail align
• Adjust glides for level
• Fasten with two hinges
Tip: Sometimes it helps to release side rail,
install hinges, then engage the side rail.
Hinges
Step 3
Top Cap
3-7/16"
Minimum
Recommended Fasteners
Dry Wall:
Must be at least 5⁄8" thick. Use 3⁄16" hollow wall fasteners or 3⁄16" toggle bolts with countersunk flat head machine screws.
Wood Studs: Must be nominal 2" x 4" size, on no more than 24" center with maximum height of 14 feet restrained at floor and ceiling.
Use #10x2" countersunk flat head screws.
Metal Studs: Must be “C” channel, 20 gauge, on no more than 24" center. Maximum height of 14 feet restrained at floor and ceiling.
Use 3⁄16" hollow wall fasteners or 3⁄16" toggle bolts with countersunk flat head machine screws.
Concrete:
Use concrete wall anchors with #10x11⁄2" countersunk flat head machine screws.
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041391 Revision B-07
T 800.482.1818
F 812.482.8300
In-line Fill Cap
Printed in U.S.A. © 2007 Kimball International, Inc.
Fill Cap
• Insert in-line fill cap
• Replace top cap
Assembly Instructions
Interworks® EQ
Page 1 of 3
Panel Set Up and Panel to Panel Connection
Tools Required
Level, 1⁄2" Wrench or Channel Locks, Screwdriver
Installation
Important: Level panels throughout installation. If stackable panels are to be installed as well, please, review the Stackable Panel Assembly
Instruction sheets first for preparation tips.
Note: Installation must be in accordance with the National Electrical Code and local codes. Electrically interconnected panels need to be
mechanically connected.
These instructions apply to tackable acoustical, glass, and tackable sectional panel. Two people are recommended, start installation at panel intersection at high spot on the floor within layout. If panel configuration includes Traxx®-mounted or wall mounted panel, start installation with that panel.
Step 1
There are two ways to create a 90° panel connection:
Unpack Panels
• Remove top cap (locate carpet gripper and cable tie)
• Remove panel hinges and wireway covers
Step 2
Hinge
• With panels in a straight line
• Adjust glides; panels must be level and aligned to each other
• Connect panels by inserting one hinge
Top Cap
Panel
Hinges
Hinge
Step 2 Alternate
Open Hinge
• With one hinge in panel side rail, open hinge 180°
by running a non-marring object down the entire
hinge/panel edge
• Remove hinge from panel side rail
Open Entire Length of Hinge
Wireway
Cover
Closed Hinge
(removed)
Ali
liggnm
nmeent
Clip
Leveling
Glide
Hinge Opened to 180º
Carpet Gripper
(shipped under Top Cap)
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041381 Revision E-09
Panel Side Rail
(top view)
Assembly Instructions
Interworks EQ
Page 2 of 3
Panel Set Up and Panel to Panel Connection, continued
Step 3
Hinge/Alignment Clip
• Swing wing panel beyond 90°
• Insert alignment clip in stationary panel, gently tap with mallet, if needed
• Pull wing panel back to 90°, engage alignment clip, gently tap with mallet
Stationary
Panel
Panel Connection with Alignment Clip Usage
Note: Alignment clips are required for panel stability
Corner/L
Alignment Clip
Alignment Clip
Straight
90º
Stationary
Panel
Corner/L
Wing Panel
Wing Panel
Corner/L
Alignment Clip
Step 3 Alternate
Panels and Alignment Clip
• Align two panels at 90°
• Adjust glides to level panels
• Insert alignment clip into both panels, gently tap with rubber mallet if needed
• Fully insert hinge, double check levelness of panels
Straight/T
4-Way
120º/3-Way
120º/V
Corner/L
Alignment Clip
Hinge
Step 4
Step 5
In-Line Straight
Connection
• Insert straight
alignment clip
• Adjust leveling glides
Connect Panels
• Fully insert panel hinges
• Plumb/level panels
• Install in-line and
connector top caps
• Install panel top caps
• Once location of station is
approved, install (1) carpet
gripper per panel
Panel
Hinge
Straight
Alignment
Clip
Carpet Gripper
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041381 Revision E-09
Assembly Instructions
Interworks EQ
Page 3 of 3
Side Rail Removal
Tools Required
Phillips Screwdriver
Loosening Panel Side Rail
Figure B
• Remove end trim if installed. (Figure A.)
• Remove side rail screws. (Figure B).
• When re-installing side rail screws, do not over-torque or side rail
may deform. (Figure C).
Figure A
Side Rail
Screws
End Trim
Figure C
Printed in U.S.A. © 2009 Kimball International, Inc.
Over Torquing
May Bow Side Rail
T 800.482.1818
Frame
F 812.482.8300
Side Rail
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041381 Revision E-09
Assembly Instructions
Interworks® EQ
Page 1 of 2
Panels – Finish Channels
Tools Required
Flathead Screwdriver, Rubber Mallet (non-marring)
Installation
These instructions apply to installation of finish channels and top caps in the configurations shown. Finish channels are required at
exposed junctions. It is easiest to install finish channels as adjacent panels are assembled. Top caps and base covers can be installed last.
Vocabulary
3-Way (Hi-Lo)
Corner
Straight (Hi-Lo)
3-Way
Corner
120º V
Top Cap
90º
3-Way (Hi-Lo)
C5 or C6
Finish
Channel
Base Covers
Panel Connections and Alignment Clip Usage
Note: Alignment clips are required for panel stability.
Alignment clips fit into alignment brackets near the base of
the panel.
Corner/L
Alignment Clip
4-Way
(used in 3-way hi-lo configurations)
Straight/T
(used in 3-way configurations
Corner/L
(used in 90° applications)
120º/V
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041392 Revision C-09
120º
Assembly Instructions
Interworks® EQ
Page 2 of 2
Panels – Finish Channels, continued
Step 1
Top-Down Method
(if enough overhead room)
• Slide finish channel into side rail grooves
• Push down to alignment brackets/clip at the top of the wireway
Note: Flex do NOT bend channel
Snap-in Method–Corner or 120° Connections Only
(if not enough overhead room)
• Pivot panel inward to narrow the junction opening
• Push into side rail grooves
• Bend and push into opposite side rail
• Push panels back to snap in finish channel
Note: Do NOT bend channel horizontally
Top Cap
Finish Channel
A
Finish Channel
B
A
B
Step 2
Alignment
Bracket
Base
Cover
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041392 Revision C-09
Printed in U.S.A. © 2009 Kimball International, Inc.
T 800.482.1818
F 812.482.8300
Base Covers
• Insert one end of base cover into wireway cover
• Pull opposite wireway cover outward
• Push base cover in
• Tap wireway cover into base cover slot
Finishing
• Install finish channel top caps
• Replace necessary panel top caps and wire covers
Assembly Instructions
®
Interworks EQ
Page 1 of 2
Supplemental Brackets and Spacer
Tools Required
Drill-drive, 1⁄4" Socket for self-tapping screws provided, 4" Extension
Installation
These instructions apply to installation of:
Supplemental Brackets for the panel connections shown;
Supplemental Bracket Spacer to compensate for depth difference between cable channels of a 10P Tackable Acoustical panel and 11P Models.
Supplemental Bracket
Supplemental Bracket and Spacer
• Remove panel top cap, lift and rotate away from panel
• Place supplemental bracket down into cable channel
• Align panels
• Use provided self-tapping screws to attach – 2 screws per
each panel
(For Difference in Cable Channel Depth)
• Remove panel top cap, lift and rotate away from panel
• Place supplemental bracket spacer into deeper cable channel
• Place 1" from vertical wall, attach with supplied screws
• Position supplemental bracket into cable channel
• Align spacer bracket screw holes with supplemental bracket holes
• Align panels
• Use provided self-tapping screws to attach supplemental bracket to
bracket spacer and panel – 2 screws per each panel
Finishing
• Replace panel top caps
Finishing
• Replace panel top caps
Self-Tapping Screw
Self-Tapping Screw
Supplemental
Bracket Spacer
L Supplemental
Bracket
L Supplemental
Bracket
Interworks EQ Panels
Interworks EQ 10P
Tackable Acoustical
Interworks EQ
11P Panels or
10P Sectional Panels
1"
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041394 Revision D-10
Assembly Instructions
®
Interworks EQ
Page 2 of 2
Supplemental Brackets and Spacer (continued)
Supplemental Bracket and Spacer
(For Hinged Door Installation)
• Remove top caps from door and adjacent panels.
• Place a door shim in the top channel on each side of the door panel. Align end of shim with the verticle frame member of the door panel.
Door shim is NOT screwed to the door panel top channel.
• Place supplemental bracket spacer in the adjacent panel. Align end of spacer with the vertical frame member of the adjacent panel.
• Use provided self-tapping screws to attach the spacer to top channel.
• Position supplemental bracket into the top channel of each panel, aligning holes in the bracket with the holes in the spacer and door shim.
• Use provided self-tapping screws to attach the bracket to the spacer in the adjacent panel and the top channel of the door panel.
Finishing
• Replace panel top caps
Self-Tapping Screw
L Supplemental
Bracket
Spacer
Door Shim
Door Panel
Vocabulary
L Bracket
S Bracket
T Bracket
X Bracket
120º Y Bracket
120º V Bracket
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041394 Revision D-10
Bracket Spacer
Door
Bracket Spacer
Printed in U.S.A. © 2010 Kimball International, Inc.
T 800.482.1818
F 812.482.8300
Adjacent Panel
Assembly Instructions
Interworks®EQ
Page 1 of 1
Panels – Door Panels
Tools Required
Level, Screwdriver, 1⁄2" Wrench or Channel Locks, Drill-Driver, 1⁄4" Socket, 4" Extension
Installation
These instructions apply to Interworks EQ hinged doors. Two people are recommended for installation. Door knob must be installed
into the door using manufacturer’s instructions. Doors cannot be placed adjacent to glass panels.
Double check correct door hinge/swing has been specified: Right hinge, the door will swing away from you to the right. Left hinge,
the door will swing away from you to the left.
Step 1
Step 2
Door Panels
• Install door knob, reference manufacturer’s instructions
• Shut and lock door
• Adjacent Panels must be level and have carpet grippers installed – if not, doors may
not open and close properly
• Connect door panel frame to adjacent panels (see Panel Set Up Instructions)
• Level door frame – the reveal around perimeter of door should be even
• Supplemental Brackets and Spacers MUST BE USED. (see Supplemental Brackets and
Spacer Instructions, Reference No. 2041394)
Recommended Hinged Door Configurations
18" wall-mounted panel
Adjacent to Corner
Supplemental
Brkts &
Spacers
Supplemental
Brkts & Spacers
Left Hinge Door
Adjacent to Three-Way/T
Use “L”
Bracket
for all “L”,
“X” and “T”
Connections
Right Hinge Door
Structural Wall
Threshold
Turn to Lower
Cover
Turn to Secure
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041388 Revision C-10
Printed in U.S.A. © 2010 Kimball International, Inc.
• Lower threshold to floor, by adjusting lower hex nut
secured to glide
• Secure threshold position with upper hex nut
• Snap cover over glide access area
T 800.482.1818
F 812.482.8300
Step 3
Assembly Instructions
Interworks® EQ
Page 1 of 1
Panels – End Trim (Full and Hi-Lo)
Tools Required
Rubber Mallet (non-marring)
Installation
These instructions apply to installation of:
End Trim required at ends of stackable panels, and at end of panel run.
End Trim
• Rest bottom of trim on: lower panel
or alignment channel
• Insert one side of trim into hinge channel
• Compress trim, press into opposite
hinge channel
Hi-Lo
End Trim
Printed in U.S.A. © 2009 Kimball International, Inc.
T 800.482.1818
F 812.482.8300
Full Height
End Trim
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041389 Revision C-09
System Assembly Instructions
Interworks® EQ
Page 1 of 1
TRAXX® Starter Kit
Includes
Wall-mount connector, 60" visual privacy tape, two spacers, weld nut(s) and Traxx screw(s) – two each for 66" and 80"H kits, one for
34" and 62" kits
Tools Required
Tape Measure, Phillips Screwdriver, Level, Wall Fasteners, Fastener Tools, two Panel Hinges (same height as kit), In-line Fill Cap
for gap between Top Cap and Traxx
Installation
These instructions apply to installation of an Interworks EQ Panel perpendicular to installed Traxx. Attach kit to Traxx and/or wall at minimum
of two points. Wall fasteners are Installer’s responsibility, see below for fasteners specifications. Kimball does not assume responsibility for their
use. To avoid leveling problems, identify high point of floor; adjust panel height to accommodate for the high point of the floor.
Step 1A
Step 2
Traxx
Attach Panel
• Remove panel top cap
• Put panel against wall-mount connector
• Adjust glides for level
• Fasten with two hinges
Traxx
WallMount
Connector
Hinges
Weld Nut
WallMount
Connector
Panels 66"
or above
Privacy
Tape
Step 3
In-line Fill Cap
Step 1B
For Panels 66" or higher with
Traxx in upper and lower
positions
• Follow first four bulleted
items in Step 1A
• Fasten weld nut to upper
Traxx
Panels Less
than 66"
Top Cap
Spacers
3-7/16"
Minimum
Recommended Fasteners
Dry Wall:
Must be at least 5⁄8" thick. Use 3⁄16" hollow wall fasteners or 3⁄16" toggle bolts with countersunk flat head machine screws.
Wood Studs: Must be nominal 2" x 4" size, on no more than 24" center with maximum height of 14 feet restrained at floor and ceiling.
Use #10x2" countersunk flat head screws.
Metal Studs: Must be “C” channel, 20 gauge, on no more than 24" center. Maximum height of 14 feet restrained at floor and ceiling.
Use 3⁄16" hollow wall fasteners or 3⁄16" toggle bolts with countersunk flat head machine screws.
Concrete:
Use concrete wall anchors with #10x11⁄2" countersunk flat head machine screws.
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041390 Revision B-07
T 800.482.1818
F 812.482.8300
Fill Cap
• Insert in-line fill cap
• Replace top cap
Printed in U.S.A. © 2007 Kimball International, Inc.
Attach Wall-Mount
Connector
For panels less than 66"
high or Traxx in lower
position only
• Attach wall-mount
connector on Traxx
so bottom of connector
is at least 37⁄16" above floor
• Cut and attach two
strips of privacy tape
(approx 281⁄2") to connector
below Traxx
• Level wall-mount connector
vertically
• Tighten weld nut
• Insert fastener through
bottom wall mount hole
and two spacers
Note: Wall fasteners are
Installer’s responsibility.
• Fasten to wall
Assembly Instructions
Interworks®EQ
Page 1 of 3
Stackable Panel
Tools Required
Level, Screwgun with #2 Magnetic Phillips Bit (2 1⁄2" minimum long), 3⁄8" Socket or Wrench
Installation
For stackable panels two people are recommended. Base panel top cap will be moved on top of assembled stackable panel. In track
of base panel, insert set of mounting brackets, (note proper orientation of brackets). Connection bolts join base panel and stackable
panel securely.
Step 1
Prep Support Panel
• Remove top cap from base panel.
• Remove panel hinges from stackable panel. (Detail A)
• Use screwdriver to spread apart top channel and insert mounting brackets into channel. Center tab on bracket against inside edge of cable slot on
channel frame. Fasten brackets to channel frame with screwgun and self tapping screws.(Detail B)
Detail A
Stackable
Panel Hinges
Connecting
Bolts
Detail B
Self Tapping
Screws
Lower Mounting
Bracket w/Threaded
Insert
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041383 Revision C-10
Lower Mounting
Bracket w/Threaded
Insert
Assembly Instructions
Interworks®EQ
Page 2 of 3
Stackable Panel, continued
Step 2
Step 3
Prep Stackable Panel Assembly
• Remove tiles from stackable panel.
- On fabric stackers, push tile up against top of J channel on stacker
frame until bottom of tile clears lip of lower J channel. Tilt bottom
of tile outward then pull down to remove it.
- On glass stackers, remove the non-glass frame half as described
above. Remove the glass frame half by first removing the screws
from the retaining clips which secure the glass frame to the stacker
frame. Remove the retaining clips, and then remove the glass frame
half as described above.
Install Stackable Panel Assembly
• Lower stacker assembly onto the base panel. The round tubes from the
stacker panel go into the vertical tubes of the base frame. Lower both
sides of the stacker panel simultaneously to prevent binding.
• Insert connection bolt through holes in bottom cross-member of
stackable panel, and fasten into lower mounting bracket installed
previously in Step 1.
• Tighten connection bolt. Do not overtighten. Stop when bottom
cross-member begins to deform.
Connecting
Bolts
Remove screws
from retaining clips
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041383 Revision C-10
Assembly Instructions
Interworks®EQ
Page 3 of 3
Stackable Panel, continued
Step 4
Step 5
Reinstall Hinges
Note: If stackable panel will be loaded on one side, go to Step 5.
• After stackable panels are installed on base panel install panel
hinges between stackable panels.
• Replace panel top caps.
Stiffener Bracket
• Cut 10" from base panel hinges (cut must be straight and level).
• Install shortened hinges into base panels.
• Install stiffener bracket into stackable panels and base panels.
• Replace panel top caps.
Stackable Panel Hinges
Stiffener Bracket
Stackable Panels
Stackable Panel
(loaded on one side)
Base Panels
Base Panels
Cut 10"
from Hinges
Printed in U.S.A. © 2010 Kimball International, Inc.
T 800.482.1818
F 812.482.8300
Base Panel
Hinges
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041383 Revision C-10
Assembly Instructions
Interworks®EQ
Page 1 of 1
Sectional Panel Tiles, Top Cap and Wireway Cover
Tools Required
Level, Screw Gun
Installation
Tile instructions apply to sectional panels. Two people are recommended, start installation with bottom tiles and work upwards.
Communication hardware and receptacles must be installed.
Top cap and base wireway instructions apply to tackable acoustical, glass and sectional panels.
To remove tiles, reverse step order.
Step 1
Step 2
Install Sectional Tiles
• Start with bottom tiles and work up
• Insert top edge of tile into upper “J”
channel on frame
• Rotate bottom of tile flat against panel
frame
• Slide tile downward until completely
seated in lower “J” channel
Glass Tiles
• Tile half with glass: insert top edge into top “J” channel
• Insert retention clip (one per vertical edge) between
glass frame and panel vertical, rotate, fasten with
screw (provided)
• Tile without glass: Same as Step 1
Glass Tile
(half w/glass)
Retention Clip:
(insert, rotate, fasten)
Self-Tapping Screw
(provided)
Glass Tile
(half without glass)
Step 3
T 800.482.1818
Top Cap
Connector
Step 4
Base-Wireway Cover
Bracket
Base-Wireway Cover
• Engage slot in
wireway cover to
bottom of bracket
• Lift up on wireway
cover and press up
over top of bracket
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041382 Revision B-09
Bracket
Base Wireway
Cover Slot
Printed in U.S.A. © 2009 Kimball International, Inc.
Mid-Wireway
Cover
Install Top Cap
and Connector
• Insert connectors
at panel-to-panel
connections
• Install top caps
F 812.482.8300
Fabric Tile
System Assembly Instructions
Interworks® EQ
Page 1 of 1
Privacy Panel
Tools Required
Level, Pencil
Kit Includes
Privacy Panel, Attachment Bracket, Double-sided Tape, Caster, Pivot Bracket with Carpet Gripper
Installation
These instructions apply to installation of a Privacy Panel. You can install the Privacy Panel at any point across the face
of an Interworks EQ Panel.
Step 1
Step 2A
Pivot Bracket and Caster
• If necessary for installation on non-carpeted floor, pry carpet
gripper out of pivot bracket
• Replace with double-stick tape
• Insert pivot bracket and caster into bottom of privacy panel
• Seat firmly
Attachment Bracket
• Stand privacy panel against panel
• Mark edge-width on top cap
• Remove top cap
• Cut double-sided tape to width of mark
Top Cap
Step 2B
• Fold tape lengthwise, stick to inside and
outside of top cap
• Remove backing
• Press attachment bracket firmly onto tape
Caster
Pivot Bracket
Double Stick Tape
Double-sided Tape
Carpet Gripper
Top Cap
Step 4
Level Privacy Panel
• Adjust position of pivot bracket and
caster to level the privacy panel
• Level in open and
closed positions
• When leveled,
press down
to anchor
pivot bracket
Pivot Bracket
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041393 Revision B-07
F 812.482.8300
Attachment Bracket
T 800.482.1818
Attach to Panel
• Insert attachment bracket
into privacy panel on the
pivot bracket side
• Replace top cap onto panel
Attachment Bracket
Printed in U.S.A. © 2007 Kimball International, Inc.
Step 3
Privacy Panel
Top Cap
Assembly Instructions
Interworks® EQ
Page 1 of 1
Power Entries: Side, End, Corner and Straight
Tools Required
Screwdriver, Rubber Mallet
Installation
Base power is available in side, end, corner and straight options to bring power to panel. Installation process will vary depending on
panel configuration and electrical requirements. End, corner and straight power entries procedures are similar, end one is shown.
Connect to power source in compliance with all local and national electrical codes.
Note: Installation must be in accordance with the National
Electrical Code and local codes. Electrically interconnected panels
need to be mechanically connected. This system may be connected
to more than one source of supply. No single circuit may be
powered by more than one source. Do not interconnect system
electrical power from different feed units. Be certain all sources are
disconnected prior to any servicing.
Step 2
End/Corner/Straight Base Power Entry
• Insert power entry into PDA, listen for snap making sure it is
seated firmly
• Install base-wireway cover
• Install power entry cover
PDA
Step 1
Side Base Power Entry
• Determine proper orientation of conduit
• Remove proper receptacle knockout on base-wireway cover
• If data/communication is to be installed, remove knockouts
• Insert module base into power distribution assembly (PDA)
listen for snap making sure it is seated firmly
Note: Occupies one receptacle location
• Install base-wireway cover
• Insert conduit plug through knockout and engage in module-base
• Install power entry cover
Field Cut
End Trim
to top of
Wireway Plate
for Base
Power Entry
Module Base
PDA
End/Corner/Straight Power Entry
Power Entry Cover
Power Entry
Cover
A
A
Receptacle Knockout
Conduit Plug
Receptacle Knockout
Data Port Knockout
B
Data Port Knockout
Install Wireway Cover
• Engage slot in wireway
cover to bracket
• Press wireway cover up
over bracket
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041386 Revision C-09
Bracket
Base Wireway
Cover Slot
T 800.482.1818
Receptacle and Data Port Knockouts
• Reference layout for receptacle and data access locations
• Firmly tap edges of knockout (A)
• Rotate knockout until free (B)
B
Printed in U.S.A. © 2009 Kimball International, Inc.
Step 3
F 812.482.8300
Conduit
Assembly Instructions
Interworks®EQ
Page 1 of 2
Power Distribution and Receptacles
Tools Required
Level, Screwdriver, Rubber Mallet
Installation
Sectional panel shown with tiles removed for clarity. Instructions apply to both tackable acoustical panels and sectional panels.
Important: Check to make sure panel run is level, prior to base wireway installation.
Note: Installation must be in accordance with the National Electrical Code and local codes. Electrically interconnected panels need to be
mechanically connected.
Step 1
Step 2
Remove Wireway Covers
• Bottom Wireway - Grasp covers and firmly pull free
• Mid Wireway - Slide tile up against top rail, tilt bottom out, then pull down
• Re-install after all powerand data installations
Power Distribution Assembly (PDA), Receptacles
• Insert PDA alignment clip, listen for snap making sure that it is
seated firmly, repeat at other end
• Slide receptacle firmly into PDA, listen for snap making sure that
it is seated firmly
Frame Slot
Power Distribution
Assembly (PDA)
Receptacle Face Plates
(Taped to inside of
Mid-Wireway Cover)
PDA Alignment Clip
Mid-Wireway
Cover
Paint Hanger Holes
on Bottom
Power Distribution
Assembly (PDA)
Receptacle
Knockout
Receptacle
Base-Wireway Cover
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041384 Revision D-10
Receptacle
Assembly Instructions
Interworks®EQ
Page 2 of 2
Power Distribution and Receptacles (continued)
Step 3
Step 4
Receptacle Face Plates (Mid-Wireway Only)
• Remove receptacle face plates taped to inside of metal
mid-wireway tiles
• Place face plates on receptacles
Receptacle and Data Port Knockouts
• Reference layout for receptacle and data access locations
• Firmly tap edges of knockout (A)
• Rotate knockout until free (B)
B
Face Plate
(Taped to inside
of Mid-Wireway
Cover)
A
A
Receptacle
Receptacle Knockout
Data Port Knockout
B
Mid-Wireway
Cover
Re-Install Wireway Cover
• Engage slot in wireway
cover to bracket
• Press wireway cover up
over bracket
Bracket
Base Wireway
Cover Slot
Printed in U.S.A. © 2010 Kimball International, Inc.
T 800.482.1818
F 812.482.8300
Re-Install Metal Tile
• 2 Holes on edge of tile go
on bottom
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041384 Revision D-10
Systems Assembly Instructions
Interworks® EQ
Page 1 of 1
Shared Neutral Wiring Diagrams
NOTE: Provide these wire diagrams to the electrical contractor.
120/208V WYE
3 PHASE 8-10
Shared Neutral
Interworks EQ: 3 and 1 Configuration
8-Wire: Receptacles;
1; 2; 3; 4 ▲
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041401 Revision A-07
Printed in U.S.A. © 2007 Kimball International, Inc.
120/240V
1 PHASE 8-10
Shared Neutral
Interworks EQ: 2 and 1 Configuration
8-Wire: Receptacles;
1; 3; 4 ▲
T 800.482.1818
F 812.482.8300
120/208V WYE
3 PHASE 8-10
Shared Neutral
Interworks EQ: 2 and 2 Configuration
8-Wire: Receptacles;
1; 2; 3 ▲ ; 4 ▲
Assembly Instructions
Interworks EQ
®
1
Panel-to Panel Jumper Cable and Transitional Jumper Cable
Tools Required

None
Installation
Note: Installation must be in accordance with the National
Electrical Code and local codes. Electrically interconnected
panels need to be mechanically connected.
Jumper cables are used to pass power from panel-to-panel at
panel base. Installation process will vary depending on panel
configuration and electrical requirements. Replace wireway
covers after all receptacles and power entries are installed.
Connect to power source in compliance with all local electrical
codes.
Note: Power cannot be passed from panel-to-panel at the midwireway.
Step 1 Panel to Panel Adjacent
Step 2 Transitional Jumper Cable
Previous 6 wire to 8 wire
Previous 4 wire to 8 wire

Insert jumper cable into power distribution assembly (PDA)
with arrow pointed up listening for snap to make sure it is
seated firmly


Repeat with adjacent Interworks EQ panel

Insert Interworks EQ end of jumper cable into PDA with
arrow pointed up listening for snap to make sure it is seated
firmly
Insert previous system end of jumper into harness block
Figure A
Figure B
Panel-to- Panel (10PEJA)
Panel-to -Post -to -Panel (10PEJB)
Corner (10PEJC)
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
2041385, Revision C
Assembly Instructions
Interworks® EQ
Page 1 of 3
Ceiling Power Entry and Power/Data Pole
Tools Required
Phillips-Head Screwdriver, Tape Measure, Drill and Bits, Hammer and Punch, Level, Ladder, Hacksaw, Utility Knife
Installation
These instructions apply to installation of: data channels to route wiring vertically between adjacent panels; power/data poles to route
wiring from ceiling to panel run; connect power harness to power source in compliance with all local electrical codes.
Note: Installation must be in accordance with the National Electrical Code and local codes. Electrically interconnected panels need to be
mechanically connected. This system may be connected to more than one source of supply. No single circuit may be powered by more than
one source. Do not interconnect system electrical power from different feed units. Be certain all sources are disconnected prior to
any servicing.
Vocabulary 1
Ceiling Power Entry Harness
Power/Communications Pole
Junction Box
Ceiling Plates
Power Harness
(hardwired end)
Upper Channel
and Cover
Data Channel
Data Channel
Top Cap
Lower Channel
and Cover
Split Panel Hinge
Data Channel
and Cover
Split Panel Hinge
Power Harness
(connector end)
Base Cover
Base Cover
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041387 Revision B-08
Assembly Instructions
Interworks® EQ
Page 2 of 3
Ceiling Power Entry and Power/Data Pole, continued
Step 1
Step 2
Shim Panel Hinge
• Take one hinge that matches height of tallest panel in junction
• Use utility knife to split hinge down middle
• Slide hinge halves into open side rail slots
• Install plastic alignment clip to connect panels at the base
Open Knockouts
• Put channel or pole into junction to measure where communication
knockouts are needed
• Open knockouts
Remove Knockouts
for Communication
Routing
Split Hinge
Utility Knife
Split Hinge
Step 3
Step 4
Step 5
Cut Ceiling Tile (Pole Only)
• Put pole against side rail and push up
to ceiling
• Level vertically
• Mark ceiling tile and cut at mark
Fasten Channel / Pole
• Push the channel or pole down to sit on
alignment clip
• Fasten to side rail with provided
#8-32 x 3⁄8" screws
Fasten Upper Channel of Data Pole
• If needed, trim top of channel for 5" minimum
overhead clearance
• Put bottom ceiling plate over upper channel
• Push upper channel through ceiling tile hole
• Place upper channel sleeve into lower channel
Min. 5"
Clearance
Ceiling Tile
Hole in Ceiling Tile
Upper Channel
Lower Channel
Plastic Alignment Clip
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041387 Revision B-08
Bottom Ceiling Plate
Assembly Instructions
Interworks® EQ
Page 3 of 3
Ceiling Power Entry and Power/Data Pole, continued
Step 6
Step 7
Power Harness (Top)
• Above ceiling tile, put top ceiling plate over data pole
• Align top and bottom ceiling plates, fasten with two #8 x 11⁄2" screws
• Attach junction box to top of pole
• Feed power harness through top of pole
• Attach power harness to junction box
• Fasten harness with hold-down clamps
• Trim upper channel cover to length if needed, put through ceiling tile
and snap into pole
Power Harness (Bottom)
• Fasten power harness into PDA (power distribution assembly)
• Snap lower channel cover into pole
• Install base cover plate
Lower Channel
Junction Box
Power Harness
(hardwired end)
Top Ceiling Plate
Bottom Ceiling Plate
Upper
Channel
Power/Data Pole
PDA
Base Cover Plate
Hold Down Clamp
Power Harness
Channel Cover
Vocabulary 2
Corner/L
In-Line
Power/Communication Poles
3-Way
4-Way
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041387 Revision B-08
Corner
End
Printed in U.S.A. © 2008 Kimball International, Inc.
3-Way
T 800.482.1818
F 812.482.8300
Communication Channels
Assembly Instructions
Interworks® EQ
Page 1 of 2
Chicago – Compliant Electrical Power
Tools Required
Drill-driver with #2 Phillips bit, Flathead screwdriver, Punch, necessary tools and testing equipment for connecting Interworks system
to an original power source, Interworks Raceway Removal Tool (no charge – contact Customer Care team to order)
Hardware Available (see drawing on right)
Interworks Panels with Chicago Power Option:
• Internal raceway with raceway covers modified to access Leviton style plugs
Chicago Junction Box (J-Box):
• Two-part J-box with two end caps (for end feed)
• Eight #8-32 Phillips flathead undercut self-tapping screws
Chicago Side Feed Plate:
• Four side feed plates (use with Chicago junction box)
J-Box
Electrical Hardware Required
Electrical installer must supply the following materials:
• Electrical wire, 12 AWG copper, color-coded for circuits and grounding
• 1⁄2" conduit, international metal hose AFS 1⁄2" trade size or equivalent
• 1⁄2" connectors
• Duplex receptacles, Leviton “Décor” #5325-1 or equivalent
Internal Raceway
(shipped assembled to panel)
End Cap
Side Feed Plate
End Cap
General Information
Install Chicago-code electrical systems after the panel installation is complete.
• Interworks panels with Chicago Power Option accept the Chicago Junction Box (J-box)
Specify this J-box separately to allow necessary hardwiring of Chicago-code electrical components
• The installer must read, understand, and adhere to these instructions and all appropriate electrical guidelines
• Electrical system MUST be hardwired by an electrical contractor licensed by the City of Chicago
• Hardware supplied by electrician MUST be U.L. listed
• Electrical duplexes CANNOT be installed back-to-back
Note: Installation must be in accordance with the National Electrical Code and local codes. Electrically interconnected panels need to be
mechanically connected.
Step 1
Remove Raceway Cover
• Insert raceway removal tool into hole at top of cover
• Lift up to release cover lock, repeat at other end of cover
• Hold tool in lock-release position and pull top of cover away from panel
Raceway Removal
Tool
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041395 Revision B-08
Assembly Instructions
Interworks® EQ
Page 2 of 2
Chicago – Compliant Electrical Power, continued
Step 2
Step 3
Install Power In-Feed
• According to electrical plan, decide how many power feeds the
installation requires
• Connect power entry points, one for each group of stations, with
no more than ten (10) duplex receptacles per circuit
• Remove knockouts to allow for in-feed of conduit:
• For end-feed power, remove knockout(s) in J-box end cap(s)
• For side-feed power, specify Chicago side feed plate(s) and
remove knockouts
• Install each half of the J-box onto the panel electrical raceway with
screws provided
• Install power entry conduit through knockout in end cap or side
feed plate
Install Chicago J-Boxes and Receptacles
Panels specified with the Chicago power option have an internal
raceway that accepts the Chicago junction box (J-box)
Note: Electrician must provide Leviton receptacles (or equivalent)
DO NOT install receptacles back-to-back
• Install into rectangular knockouts provided in face of J-box so that
plug faces outward, hardwire the receptacles using screws supplied
with the duplexes
• Install each half of the junction box onto the panel electrical raceway
with screws provided
• To continue hardwiring to the next panel, install 1⁄2" appliance flex
jumper conduit and wire from the end cap to the end cap in the
next panel
PRIOR TO ENERGIZING: test the system for its ability to withstand
dielectric voltage (high potential) per U.L. 1286, text #33
• Replace Raceway covers
Internal Raceway
(shipped assembled to panel)
J-Box
End Cap
Internal Raceway
(shipped assembled to panel)
J-Box
End Cap
End Cap
Side Feed Plate
End Cap
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041395 Revision B-08
T 800.482.1818
End Cap
Printed in U.S.A. © 2008 Kimball International, Inc.
Internal Raceway
(shipped assembled to panel)
J-Box
F 812.482.8300
Conduit
(hardwired to next panel)
Assembly Instructions
Interworks® EQ
Page 1 of 2
New York City – Compliant Electrical Power
Tools Required
Phillips-Head Screwdriver with #2 bit, Flathead Screwdriver, Rubber Mallet, Punch, Wire Cutters, 12-Gauge Wire Nuts, necessary tools
and testing equipment for connecting Interworks system to an original power source, Interworks Raceway Removal Tool
(no charge – contact Customer Care team to order)
Hardware Supplied (see drawing on right)
• Electrical cable/harness to match power option specified
• Internal raceway with junction boxes
• Cover plate and end caps
• Two raceway covers, one with power knock-out
Internal Raceway
Electrical Hardware Required
Electrical installer must supply the following materials:
• 3⁄4" O.D. x 18" long liquid tight flex conduit
• Electrical wire, 12 AWG copper, color-coded for circuits and grounding
• 1⁄2" conduit, international metal hose AFS 1⁄2" trade size or equivalent
• 1⁄2" connectors
General Information
New York-compliant electrical power can be added under these conditions:
• Use only the New York Retrofit Kit
• Only Interworks EQ non-powered in-feed panels can accept the retrofit kit
• Available in 30"W – 60"W panels only
• Mid-height access not available
• Installer must read, understand, and adhere to all appropriate electrical guidelines
If you have questions concerning these instructions, please call Customer Care team
• A licensed, approved electrician must perform installation
End Cap
J-Box
Cover Plate
Knockout
Raceway Cover
Jumper Cable
Cautions
• Installation must be in accordance with the National Electrical Code and local codes.
• Disconnect ALL power to panels prior to servicing or installation, including removal of raceway cover.
• Electrically interconnected panels need to be mechanically connected.
• DO NOT interconnect panels powered from different feed units – this can cause shock and fire hazard.
• This panel system may connect to more than one source of power supply.
• No single circuit may be powered by more than one source.
• A licensed, approved electrician must perform installation.
Step 1
Step 2
Remove Wireway Cover of Non-Powered Panel
Remove Existing Wireway Brackets
• Remove wireway brackets
from in-feed panel
Wireway Bracket
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041396 Revision B-08
Assembly Instructions
Interworks® EQ
Page 2 of 2
New York City – Compliant Electrical Power, continued
Step 3
Step 4
Assemble Retrofit Raceway
• Decide which raceway side will receive power in-feed
• Attach cover plate to J-box on side that will receive in-feed
• Install J-boxes and end caps into retrofit raceway kit
• Install assembled retrofit raceway onto panel
Electrical Junction to Infeed Panel
• Insert the 3⁄4" liquid-tight conduit through raceway cover that has knockout
(customer supplied)
• Install conduit into J-box (couplers not provided), tighten fitting
• Insert jumper cable through end cap and into J-box
• Splice conduit wires to matching jumper cable wires (wire nuts not provided)
• Connect to power distribution assemblies (PDAs) and jumper cables in remaining panels
• Replace raceway covers
Splice inside J-Box
Internal Raceway
End Cap
Conduit
J-Box
Cover Plate
Electrical Testing
• BEFORE CONNECTING to building electrical power:
• Determine which power option is to be installed – 3 and 1 or 2 and 2
• Test the system for its ability to withstand dielectric-voltage
(high-potential) per U.L. 1286 Test #33
• Connect power input cables to power source in compliance with power option
and all applicable electrical codes
• Test the entire system for proper operation
3 and 1 (8-wire)
1
3
1
4
5
4
4
Hot
1
Hot
4
Hot
2
Hot
NEU
2
Hot
5
Hot
3
Hot
GRD
NEU
NEU
GRD
GRD
GRD
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2041396 Revision B-08
2
1
Hot
NEU
Raceway
Removal Tool
2
2 and 2 (8-wire)
T 800.482.1818
Step 6
Remove Raceway Cover, if necessary, once installed
• Insert raceway removal tool into hole at top of cover
• Lift up to release cover lock, repeat at other end of cover
• Hold tool in lock-release position and pull top of cover away
from panel
Printed in U.S.A. © 2008 Kimball International, Inc.
Step 5
F 812.482.8300
Jumper Cable
Assembly Instructions
Interworks EQ
Interworks EQ® Panel Tackboard
Page 1 of 1
Figure A
Tools Required
■
Phillips Screwdriver
Package Contents
■
Tackboard with
attached tracks
■
■
4 Hook Brackets
4 1⁄2" Phillips Head Screws
Panel Tackboard
Installation
3.
4.
Hook
bracket
F 812.482.8300
2.
Figure B
Printed in U.S.A. © 2008 Kimball International, Inc.
Figure C
T 800.482.1818
1.
Note: These instructions provide the basic information to
install a panel tackboard onto Interworks panels. (Figure A).
Tackboard can be equal to or greater than the width of the
panel(s) onto which it will be installed. One person can
perform all operations.
Note: Panels must be properly installed and level prior to
installation of tackboard.
Turn tackboard face down. Locate two parallel tracks
running the length of the component.
Insert one hook bracket into each end of track, hooks to the
outside and pointing down. (Figure B).
Slide hook brackets into desired location along track to
correspond to panel side rails and anchor with four 1⁄2"
Phillips head screws provided if using full width. (Figure C).
Insert into panel side rails at desired location.
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1741490 Revision E-08
Systems Assembly Instructions
Footprint®
Transaction Counter
on Interworks® EQ
Page 1 of 1
Figure A
Tools Required
Variable Speed Drill
#2 Phillips Tip Bit
Package Contents
#10 x 1" Phillips Panhead Screws
General Information
■
■
■
■
■
Counter
Bracket,
right
Transaction counter width must equal panel width.
Two sets of left and right handed support brackets are
included with each counter top.
One person can perform all operations.
Panels and finish channels must be properly installed,
squared and leveled prior to counter top installation.
Route all communications prior to installing counter.
Figure B
Installation
1. Locate position where counter top will be installed into
panel. Insert each set of left and right handed support
brackets into top slot of panel side rail. (Figure A).
Note: Panel top cap is not removed. All panel finish trim
should already be installed.
2. Lay counter top onto brackets and center top approximately
6 1⁄2" overhang on either side of top.
3. Secure with #10 x 1" screws provided, two screws per
bracket.
F 812.482.8300
■
Counter
Bracket,
left
Transaction Counter
6 1⁄2"
6 1⁄2"
Overhang
each side
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1567904
Revision D-07
T 800.482.1818
■
Printed in U.S.A. © 2007 Kimball International, Inc.
■
Assembly Instructions
Footprint®
Page 1 of 2
Bevel Profile Overhead Storage
To Interworks® EQ Panels
Figure A
Lock Clip
Tools Required
■
■
Tape Measure
Drill with #2 Phillips Bit
■
Rubber Mallet
Right
General Information
■
These instructions provide the basic information to install
bevel profile overhead storage units onto Interworks EQ
panels.
■
For ganging two side-by-side units, contact Customer Care.
One person can perform installation, although for larger
units, two persons are recommended.
■
Left
Figure B
Installation
Units hang on the Interworks EQ panel via vertical hook
brackets, which are part of the unit's side walls. A lock clip
(designed for use with bevel profile overhead storage only)
helps prevent unintentional removal from the panel.
1. Locate lock clip installed in upper rear corner of unit.
Remove and reposition so unnotched flange aligns with
second hook in rear bracket. (Figure A).
2. Determine vertical position at which unit will be located:
- Panels feature a resilient, black slot mask which is pushed
aside during bracket installation.
- When hanging bevel profile overhead storage and shelf
side-by-side, units look best when bottom edges are flush.
Tip: To make top of overhead flush with top of panel,
hang unit in uppermost side rail slot.
3. Insert hooks along rear left and right sides of unit into panel
side rail slots at desired height. (Figure B).
■
Bevel profile units mount to Interworks EQ
panel via vertical hook brackets at rear of unit
(indicated by grey lines)
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1699144
Revision G-08
Assembly Instructions
Footprint
Installation (continued)
“Ganging” Two Side-by-Side Units
Page 2 of 2
Figure C
1. Locate pre-drilled holes.
A support clip is required to balance load and for even
spacing between units. Contact Customer Care to order.
1. Locate pre-drilled holes under units and ensure they are
aligned. (Figure C).
2. Secure support clip using two #10x¹⁄₂" Phillips panhead
screws provided.
■
Support Clip
Printed in U.S.A. © 2008 Kimball International, Inc.
T 800.482.1818
F 812.482.8300
2. Secure Support Clip with screws.
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1699144
Revision G-08
Systems Assembly Instructions
Footprint®
Page 1 of 2
Bevel Profile Half Height and
Full Height Shelf To Interworks®
EQ Panels
Tools Required
■
■
Tape Measure
Drill with #2 Phillips Bit
Full Height Shelf Only:
7. Lay unit flat with hooks of side walls facing you.
Slide bookstop so bottom area (multiple holes) lines up
with holes in back of shelf. Slot holes in top flange should
slide over L-bracket, which are mounted on the side walls.
Screw bookstop to back of shelf and to side wall L-brackets.
Figure A
■
Rubber Mallet
Right
side wall
Right
side wall
Bookstop
General Information
■
■
These instructions provide the basic information to
assemble and install bevel profile half height and full height
shelves onto Interworks EQ panels.
One person is required to assemble units up to 48"W.
For 54"W and larger units, two persons are recommended.
Shelf
Shelf
Left
side wall
Full Height Shelf
Left
side wall
Half Height Shelf
Installation
■
1.
2.
3.
4.
5.
6.
Shelves are shipped Ready-to-Assemble (RTA) in four parts:
shelf, left side wall, right side wall and bookstop. (Figure A).
Lay right side wall on ground, rear attachment
brackets/hooks facing toward you. (Figure B).
Note: Flange on the inside of the side wall contains two
assembly holes and a rounded tab.
Position shelf perpendicular to side wall.
Note: The underside of shelf contains a flange with holes
and a square cutout corresponding to side wall holes and tab
location.
Align tab in side wall flange to square cutout in underside
of shelf. Slide the side wall onto the shelf so tab disappears
and flanges are even.
Tap front of shelf gently with rubber mallet until holes in
flanges are aligned.
Repeat assembly for left side wall.
Screw side wall to shelf using two screws provided,
one per side.
Note: An additional hole is provided for “ganging” two
side-by-side units together. If you do not plan to gang the shelf
to another unit, you may opt to further secure shelf using
additional screws provided. (Figure B).
Figure B
Shelf
Side wall
Hole used for
“ganging”
Right side shown
1. Slide tab in flange of side wall
into corresponding knockout
in shelf.
2. Align holes and secure with
screws provided.
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1699148
Revision B-07
Systems Assembly Instructions
Footprint
Installation (continued)
Page 2 of 2
Figure D
To Interworks EQ Panel
Units hang on the Interworks EQ panel via vertical hook
brackets, which are part of the unit’s side walls.
1. Determine vertical position at which unit will be located:
- Panels feature a resilient, black slot mask which is pushed
aside during bracket installation.
- When hanging overhead storage and shelf side-by-side,
units look best when bottom edges are flush.
Tip: To make top of overhead flush with top of panel,
hang unit in second slot from top of Interworks panel.
2. Insert hooks along rear left and right sides of unit into
panel side rail slots at desired height. (Figure C).
■
1. Locate pre-drilled holes.
Ganging Bracket
“Ganging” Two Side-by-Side Units
A ganging bracket, specified separately, is required to
balance load and for even spacing between units.
1. Locate pre-drilled holes under units and ensure they are
aligned. (Figure D).
2. Secure ganging bracket using two #10x 1⁄2" Phillips panhead
screws provided.
■
2. Secure Ganging Bracket with screws.
Full Height Shelf illustrated
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1699148
Revision B-07
Printed in U.S.A. © 2007 Kimball International, Inc.
T 800.482.1818
F 812.482.8300
Figure C
Systems Assembly Instructions
Footprint®
Page 1 of 3
Installing Cetra®/Interworks® EQ
Panel Attachment Brackets to
Lunar Overheads
Figure A
Tools Required
■
■
#2 Phillips Screwdriver
1
⁄4 " or 3⁄8 " Socket Driver
⁄16 " Hex Socket
⁄16 " Open End Wrench
■
7
■
7
Package Contents
■
Cetra/Interworks EQ Panel
Attachment Bracket (LH)
■
Cetra/Interworks EQ Panel
Attachment Bracket (RH)
■
Doubler Bracket
■
1
⁄4 " Bolt, washer and nut
Note: This instruction covers installation of panel attachment
brackets to Lunar overheads that will be mounted on Cetra or
Interworks EQ panels. All operations to assemble the bracketry
can be done by one person, but it is recommended that a two
person team assemble and install the units to the panel system.
Important: Reference the assembly instruction “Lunar
Overhead Storage, Flipper Door Cabinet” for assembly of
the Lunar Overhead. The units are assembled in the inverted
position. Moving the units without the bracketry attached can
cause damage, therefore all bracketry in this instruction is
installed with the overhead unit in the inverted position.
1. The assembled overhead unit is in the inverted position.
(Figure A).
2. For Lunar overhead to be mounted on Cetra panel:
The hook-type attachment brackets are right-handed and
left-handed. The flange sides with the hooks orient toward
the outer end of the overhead. Additionally, the doubler
bracket mounts over the inboard face of the main bracket.
The elongated end hook (rhino horn) is oriented towards
the top of the case. All brackets are attached using ¹⁄₄" bolts,
nuts, and washers. Take note of location of mounting holes
and attach bracket and doubler bracket to unit as shown
using three (3) bolts, three (3) washers, and three (3) nuts
per bracket. Loosely secure the fasteners. (Figure B).
Figure B
Bottom Shelf
Panel Attachment
Bracket
Doubler Bracket
(Cetra only)
Top
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1699194
Revision B-07
Rhino Horn
Systems Assembly Instructions
Footprint
Page 2 of 3
Installation
Figure C
3. Slide the attachment bracket OUTWARD to the extent of
the slots. Slide the doubler bracket towards the top of the
case. Hold brackets in position and tighten all fasteners
securely. (Figure C).
4. Repeat Steps 2 and 3 to attach brackets to the opposite end
of the case. (Figure D).
5. For Lunar overhead to be mounted on Interworks panel:
Follow Step 2 but DO NOT attach the doubler bracket.
6. Slide the attachment bracket INWARD to the extent of the
slots. Hold bracket in position and tighten all fasteners
securely. (Figure E).
Remember: Doubler brackets are NOT USED for Interworks
panel mount.
7. Repeat Steps 5 and 6 to attach bracket to the opposite end of
the case.
Slide Attachment
Bracket outward
to extent of slots
Slide Doubler Bracket
towards top as far as
possible
Top
Figure D
Figure E
Bottom Shelf
Panel
Attachment
Bracket
For Cetra,
brackets mount
at outer extent
of slots
Doubler Bracket
(Cetra only)
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1699194
Revision B-07
For Interworks,
brackets mount
at inner extent
of slots
Systems Assembly Instructions
Footprint
Installation
Page 3 of 3
Figure F
Panel slots
Figure G
Printed in U.S.A. © 2007 Kimball International, Inc.
T 800.482.1818
F 812.482.8300
8. To mount completed unit to Cetra: Carefully turn unit
upright. It is recommended that two persons be used to
lift the unit to its final position. Lift unit and tilt slightly
backwards. Engage rhino hooks on attachment brackets
into vertical panel slots on Cetra panel. Rotate unit down,
making sure all other hooks on attachment brackets engage
panel slots. Press down on unit to lock all hooks into
position. (Figure F).
9. To mount completed unit to Interworks EQ: Carefully turn
unit upright. It is recommended that two persons be used
to lift the unit to its final position. Lift unit and tilt slightly
backwards. Engage rhino hooks on attachment brackets
into vertical panel slots on Interworks panel. Significant
pressure may be required to install unit as a rubber slot
mask is being forced aside with the action of the hooks
going into the slots. Rotate unit down, making sure all
other hooks on attachment brackets engage panel slots.
Press down on unit to lock all hooks into panel. (Figure G).
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1699194
Revision B-07
Assembly Instructions
Footprint Support
®
Interworks EQ® Panel Mounted
Worksurface
1
Figure C
Tools Required




Tape Measure
Drill with torque option
#2 Philips head bit
#2 R-2 square screwdriver bit
Installation
Note: Panel mounted worksurface brackets are provided in two
types, left or right. (Figures A & B). The top of the brackets
should be located 22 3/4 " from the top of the wireway cover
for standard height and 19 3/4" for typing height. (Figure C).
1.
Insert hook on the top of bracket into the panel frame slot
at a 45° angle. (Figure D).
2.
Push the top of the bracket downward allowing locking tab
to engage in the panel slot. (Figure E).
3.
Install a bracket at each panel joint in the worksurface
layout.
Note: When installing the worksurface brackets along the
center, you must alternate left brackets and right brackets to
prevent a shortage of brackets. (Figure F). If you run short of
either left or right brackets, refer to alternate installation
diagram. (Figure G).
Note: A structural cantilever must be used in place of the
standard worksurface brackets when the open kneespace is
greater than 48" for 1 3/16" surfaces and 60" for 1 9/16" surFigure A
Left
Figure D
Figure F
Figure B
Right
Figure G
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
1847179, Revision D
Figure E
Assembly Instructions
Footprint Support
®
Interworks EQ® Panel Mounted
Worksurface
2
Figure J
Installation (continued)
4.
Place worksurface on clean, solid surface, back side facing
up. Install the flat brackets on the "main" worksurface,
approximately 2" from front edge and approximately 6"
from back edge of the adjoining worksurface using the
screws provided. (Figure H). Ensure that the flat bracket
attachment does not interfere with other brackets or
components. Two flat brackets are required to join surfaces
end to end or at a right angle.
5.
Square all panels to aid in alignment and consistent reveals
between worksurfaces and panels. (Figure I).
6.
Lay the worksurface on the brackets. (Figure J).
Tip: Use an undersurface component as additional support
until the worksurface bracket is secured to the surface.
7.
Lay adjoining worksurface onto brackets.
Note: When attaching two surfaces at a right angle, there
will be a 1/8" gap between the wire manager and panel.
(Figure K). If there is no wire manager, the surfaces should
align. (Figure L).
8.
Attach adjoining worksurface to the flat brackets with
screws provided. (Figure M). Eight screws required per
bracket.
9.
Adjust worksurface location to ensure alignment of surface
joints with panel reveals, if applicable, and control gaps
between panel and edges of worksurfaces. DO NOT press
wire manager into panel.
10. Attach the worksurfaces to the worksurface brackets using
the screws provided. (Figure N). A minimum of two
screws
Figure H
Figure K
Figure M
Figure N
Figure I
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
1847179, Revision D
Figure L
Assembly Instructions
Footprint®
Page 1 of 2
Worksurface Cantilever Bracket
for Interworks® EQ Panel
Figure A
Tools Required
■
■
■
Drill with Torque Option
#R-2 Square Srewdriver Bit
Rubber Mallet
■
■
Tape Measure
Level
Standard
Height
Package Contents
■
24"
#8 x .75 Robinson Head Flakeboard Screw
General Information
■
Cantilevers are required when placing two surfaces end to
end, when open kneespaces are greater than 48" for 1 3/16"
surfaces or 60" for 1 9/16" surfaces, or in configurations
where standard panel worksurface bracket support is not
possible. Cantilevers are designed so that a single bracket
can share the load between two adjacent surfaces. They
can be used as sole support for a worksurface. The top of
the cantilever should be located 24" from the bottom of
fabric for standard height (29" nominal). (Figure A).
Figure B
Installation
1. Insert hook on the top of cantilever into the slot on panel
siderail at a 45˚ angle. (Figure B).
2. Push the top of the cantilever downward. (Figure C).
Important: Use mallet to make sure bracket is seated and
fully engaged.
45˚
Figure C
2
1
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1847185 Revision D-09
Assembly Instructions
Footprint®
Installation (continued)
Page 2 of 2
Figure E
Note: Cantilevers (with cutout to inside) are required with
corner surfaces. (Figure D) With use of split top corner surface,
corner cantilevers (with cutout to outside) must be located
under adjacent surfaces. (Figure E). Cantilevers can be used as
required support when open kneespace is greater then 48" for
1 3/16" surfaces and 60" for 1 9/16" surfaces. (Figure F).
3. Attach worksurfaces with flat brackets and adjust alignment,
if applicable.
4. Attach cantilever to worksurface with screws provided.
Figure D
Printed in U.S.A. © 2009 Kimball International, Inc.
Kimball Office T 800.482.1818
F 812.482.8300
Figure F
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1847185 Revision D-09
Systems Assembly Instructions
Footprint®
Worksurface Support Panel,
Return Support Panel
Page 1 of 1
Figure A
Return Support Panel
(no filler panel)
Worksurface Support Panel
(includes filler panel)
Tools Required
■
■
■
Variable Speed Drill
#2 Phillips Tip Bit
Level
Package Contents
Inside
General Information
■
Inside
Figure B
Figure C
These instructions provide the basic information to install a
Worksurface Support Panel or Return Support Panel onto
any worksurface. (Figure A).
Installation
Gusset
Bracket
F 812.482.8300
1. Worksurface support panel includes a filler panel.
Remove filler panel by sliding up and out. (Figure B).
2. If using with gusset bracket, secure gusset bracket to
support panel prior to installing to worksurface. (Figure C).
3. If using with modesty panel, secure modesty panel to
support panel prior to installing to worksurface. (Figure D).
4. To install directly to surface, secure using three #10 x 1"
screws, provided. (Figure E).
5. Reinstall worksurface support panel filler, if applicable.
(Figure E).
Figure D
Figure E
Modesty Panel
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1567912
Revision C-05
T 800.482.1818
■
Outside
Outside
Support Panel
3 #10 x 1" Phillips Particleboard Screws
Printed in U.S.A. © 2004 Kimball International, Inc.
■
Systems Assembly Instructions
Footprint®
Page 1 of 3
Worksurface End Panel
Tools Required
■
■
■
Drill with Torque Option
#2 Phillips Head Bit
6" Magnetic Phillips Tip Bit
or, Screwdriver
■
■
Tape Measure
Level
Package Contents
■
■
#10 x 1" Phillips Panhead
Particleboard Screws
1
⁄4-20 x 3⁄4" Round Head
Machine Screws
■
#10 x 1" Hex Washer Head
Drill Tip Screws
Installation - End Panel/Worksurface Brackets
1. Smooth side should be facing away from the worksurface
being supported by the end panel.
2. Two L-shaped end panel/surface brackets secure end panel
to worksurface.
3. Determine whether end panel will be left or right. Relocate
glides as needed.
4. Place end panel smooth side down, glides closest to you.
5. Locate pre-drilled holes for attaching end/panel surface
brackets. Secure end panel/surface brackets to end panel
using #10x 1⁄2" screws. (Figure B).
Note: Hole patterns differ for full end and half end panel.
Figure A
General Information
■
■
■
■
■
■
■
These instructions provide the basic information needed to
install any metal end panel into an Interworks® EQ panel.
Corner worksurfaces are predrilled to accept End Panel for
installation in standard flush left/right position.
Installation process is similar for both half end panel (18"D)
and full end panel (24", 30"D). Full end panel is illustrated.
Unsupported worksurface span must not exceed 60".
Kimball will not assume liability for any improperly or
inadequatedly supported worksurface.
Instructions are provided to install worksurface at standard
desk height (28³⁄₁₆" actual height).
End panel is designed to secure (Figure A):
a) Surface and panel at end of run when no wing panel is
used or when undersurface is less than full depth/height.
b) Surface and panel when full height undersurface support
is required, e.g. with some corner applications.
b)
Sample Configurations
(Brackets indicated by dotted lines)
a)
Figure B
End panel can be used to “share” load between two surfaces.
(See Page 3).
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1567913
Revision C-07
Systems Assembly Instructions
Footprint
Installation - End Panel/Side Rail Tie Brackets
Page 2 of 3
Figure C
1. Two reversible end panel/side rail tie brackets seucre end
panel to panel side rail.
2. Rear of end panel is open to accept two tie brackets. A
notch in the opening corresponding to the width of the tie
bracket. Internal structure of end panel has threaded nuts
for installation of tie brackets.
3. Locate notches in rear of end panel. Insert bracket, hooks
facing away from rear of end panel, flush against the notch
at the rear of the end panel.
4. Using a minimum of 6" magnetic Phillips tip
bit/screwdriver, secure brackets to end panel using
1
⁄4"-20 screws, provided. (Figure C).
Installation End Panel to Panel, Worksurface
1. Place end panel in desired location and insert hooks on
brackets into panel side rail. (Figure D). Hooks are designed
to engage the side rail slots in the “up” position; extend End
Panel glides to secure End Panel.
2. Place worksurface on top of End Panel. Square and level,
readjusting End Panel glides as needed.
Front edge—worksurface should be slightly
recessed from front edge of panel side rail.
Rear edge—surfaces are flush against the panel.
3. You may or may not want to secure End Panel to surface
just yet, depending on other brackets and undersurface
storage being installed.
Tip: All surfaces should be in place, squared and level before
you screw in brackets to surfaces. This makes any minor
adjustments easier.
Note: When undersurface storage is installed adjacent to
End Panel, storage and End Panel may be secured to
worksurface at the same time through aligned holes in
storage and End Panel/Surface Brackets. (Figure E).
4. Secure End Panel/Surface Brackets to worksurface using
(four) #10x1" screws provided per bracket.
Figure D
Figure E
(Rear view)
Spacers
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1567913
Revision C-07
Systems Assembly Instructions
Footprint
Installation - One end panel to support two
Page 3 of 3
Figure F
worksurfaces
(Rear view)
Figure G
(Rear view)
Printed in U.S.A. © 2007 Kimball International, Inc.
T 800.482.1818
F 812.482.8300
1. Additional set of End Panel/Surface Brackets is required.
Contact Customer Care to order.
2. Install all (four) End Panel/Surface Brackets to End Panel,
two per side. End Panel is predrilled on one side.
To mark smooth side, measure hole patterns on pre-drilled
side and transfer to smooth side. Drill holes.
3. Insert bracket, hooks facing away from rear of End Panel,
flush against the notch at the rear of the End Panel.
(Figure F).
4. Place end panel in desired location and insert hooks on the
brackets into panel side rail. End panel should be centered
on panel hinge. (Figure G).
5. Extend End Panel glides to secure End Panel.
6. Place surfaces onto End Panel (and other installed brackets).
Ensure it is level and square.
7. Secure End Panel/Surface Brackets to surface using (two)
#10x1" screws provided per bracket.
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 1567913
Revision C-07
MODULAR CASEGOODS—End Panel
Assembly Instruction
Figure A
General Information
• These instructions provide the basic information to install an
Interworks® End Panel, e.g. to create a freestanding desk.
Glides
• Arc worksurfaces are predrilled to accept End Panel in
standard flush left/right position only.
• For Rectangular and non-standard position, worksurface
must be drilled.
• Process is similar for both Full and Half End Panel. Full End
Panel is illustrated.
Holes for securing
Modesty Panel
• Half End Panel is often used to create a freestanding Corner
desk.
• When an Undersurface Lateral File is used, a Full End Panel
is required to support desk on the same side as the File.
Figure B
• One person can perform all operations, although two may be
required to handle larger, heavier units.
Tools Required
1
• Drill with /8" and #2
Phillips tip bits
•
5
/16" Hex socket
• Level
Hardware
• Metal to worksurface:
#10x1" Phillips pan head
particleboard screws.
• Metal to metal: #10x1/2"
Hex washer head drill
screws.
End Panel Installation
• End Panels include brackets for attaching to worksurface and
predrilled holes to secure Modesty Panel (Figure A).
Figure C
1. Determine location of End Panel, left or right. Relocate the
two glides to the opposite side of support as needed.
2. For Arc worksurface, use predrilled holes as a guide.
1.
2.
For Rectangular worksurface, inset End Panel approximately
/8" from front and back of worksurface, and approximately
1
/16" from side of worksurface.
1
Secure front and rear End Panel/Worksurface Brackets to
worksurface with four #10x1" screws per bracket (Figure B).
3. Turn End Panel upside down and align to installed brackets.
Holes in the End Panel should be to the INSIDE and the
glides should be facing UP. Secure loosely with two #10x1/2"
screws (Figure C).
NOTE: After you have installed the Modesty Panel, you need
to retighten all screws.
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent. If you have any
questions concerning these instructions, please call your Customer Care Team.
Tel. 800.482.1818
Fax 812.482.8300
Form No. HAIIWFS006B-01
Printed in U.S.A.
© 1999 Kimball International, Inc.
1
Assembly Instructions
Interworks®EQ
Page 1 of 1
Field Removal and Installation of Monolithic Tackable Acoustical Tiles
Tools Required
Putty Knife, Utility Knife, Linoleum Roller or similar type roller (Available at most hardware stores.)
Hard plastic applicator (Such as a credit card or small scraper.)
Installation
These instructions apply to Monolithic Tackable Acoustical Panels.
Step 1
Step 2
Remove Existing Tile
• Use a putty knife to pry tile free from “J” channels and existing tape.
• After tile is removed, use a putty knife to scrape away any remaining
fiberglass and PSA still stuck to the panel frame. It may help to “roll”
old tape (PSA) off of metal with finger.
Install New Tile
• Apply PSA, 3M 6038 to Panel Frame as shown. Use the plastic applicator
to press tape firmly against panel frame. See figure below for PSA
application.
• Remove backing paper from adhesive.
• Insert bottom edge of new tile into bottom “J” channel. Ensure that
tile is seated completely against bottom of “J” channel and is centered
evenly. Do not allow tile to contact the adhesive yet.
• Gently bow the tile outward slightly to allow it to slip into the top “J” channel,
making sure that the tile is centered evenly in the top “J” channel.
• Press tile flat against the panel frame, again making sure that it is
centered evenly horizontally and the gap between the tile and side rail
is consistent on both sides from top to bottom.
• With a linoleum roller, or similar type roller, roll the tile where the
adhesive was applied, being careful not to crush the tile and making
sure that the roller stays on the horizontal cross members.
Note: Diagram is for 66" and 80" panels. Same process applies to all
other heights, except there is no upper cross-member to apply PSA.
Apply PSA, 3M 6038 as shown
to both sides of panel
Printed in U.S.A. © 2010 Kimball International, Inc.
T 800.482.1818
Full Height
F 812.482.8300
Full Width
Apply
Verticle Tape
to Flange of
Side Rail
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Service.
Part No. 2241236 Revision B-10