Wiring Diagram Amana Technical

advertisement
Amana Technical Information
 Refrigerator
Wiring Diagram
!
WARNING
To avoid risk of electrical shock that can cause death or severe personal injury, disconnect unit from power before
servicing unless tests require power. Discharge capacitors through a 10,000-ohm resistor before handling. Wires
removed during disassembly must be replaced on connect terminals to ensure proper grounding and polarization.
ARB1905C*
ARB1917C*
ARB2205C*
ARB2214C*
ARB2217C*
DRB1901C*
DRB2201C*
PARB1905CB0, PARB1905CC0,
PARB1917CB1, PARB1917CC1,
PARB2205CB0, PARB2205CC0,
PARB2214CB1, PARB2214CC1,
PARB2217CB0, PARB2217CC0,
PDRB1901CC0, PDRB1901CW0
PARB2201CC0, PARB2201CW0
PARB1905CW0
PARB1917CS0, PARB1917CW1
PARB2205CW0
PARB2214CS1, PARB2214CW1
PARB2217CS0, PARB2217CW0
• Due to a possibility of personal injury or property damage, always contact an authorized technician for
service or repair of this refrigerator.
• Refer to Service Manual RS1200005 for installation, operating, disassembly, icemaker, testing, and
troubleshooting information.
!
CAUTION
All safety information must be followed as provided in Service Manual RS1200005.
!
WARNING
To avoid risk of electrical shock that can cause death or severe personal injury, disconnect unit from power before
servicing unless testing is required. Discharge capacitors through a 10,000 ohm resistor before handling. Wires
removed during disassembly must be replaced on correct terminals to ensure proper grounding and polarization.
Kw/24 hr ± 0.4
Ambient ° F
19 cu ft
22 cu ft
65°
.9
.9
90°
1.4
1.5
110°
2.0
2.1
No-Load Performance, Controls in Normal Position
Refrigerator Center
Compartment
Percent Run Time
Average Food
Cycles/24 hr
± 10%
Temperature ± 3°° F
± 25%
65°
25
25
90°
40
40
110°
60
60
65°
33
30
90°
30
27
110°
24
22
65°
38
38
90°
40
40
Freezer Compartment
Average Food
Temperature ± 3°° F
110°
42
42
65°
0
0
90°
0
0
110°
0
0
Temperature Relationship Test Chart
Ambient ° F
19 cu ft
22 cu ft
T-1 Outlet
± 3°° F
65°
90°
-15
-14
-15
-14
T-2 Inlet
± 3°° F
65°
90°
-15
-14
-15
-14
T-3 Suction Line
± 7°° F
65°
90°
65
95
65
95
Average Total
Wattage ± 10%
65°
90°
135
140
135
140
Suction
Pressure
± 2 In. Hg
65°
0
0
90°
1
1
Head Pressure
± 5 PSIG
65°
90°
83
135
83
135
Schematic
November 2001
Amana Appliances 2001
4
12642402 Rev. 0
November 2001
1
12642402 Rev. 0
Component Specifications
!
Damper Replacement
!
WARNING
To avoid risk of electrical shock that can cause death or severe personal injury, disconnect unit from power before
servicing unless tests require power. Discharge capacitors through a 10,000-ohm resistor before handling. Wires
removed during disassembly must be replaced on connect terminals to ensure proper grounding and polarization.
WARNING
To avoid risk of electrical shock that can cause death or severe personal injury, disconnect unit from power before
servicing unless tests require power. Discharge capacitors through a 10,000-ohm resistor before handling. Wires
removed during disassembly must be replaced on connect terminals to ensure proper grounding and polarization.
Replacing Damper Control
Part Number
Component
C8931612
Compressor run capacitor
12049717
Compressor
12571702
Damper control
Specifications all parts
115VAC/60HZ unless noted
Volt.....................................................
Capacitance ......................................
BTUH .................................................
Watt ...................................................
Current Lock rotor..............................
Current Full load.................................
Resistance Run windings...................
Resistance Start windings..................
12351008
Freezer temperature control
Settings
#1 – out..............................................
#4 – in ................................................
#4 – out..............................................
#7 – out..............................................
10884507
Condenser motor
Rotation (facing end opposite shaft)
RPM
Watt....................................................
Current...............................................
210/220 VAC
15 µfd ± 10%
865 BTUH
60 Hz / 168 watts
19.5 amps± 15%
1.35 amps± 15%
2.79 ohms ± 15%
4.49 ohms ± 15%
Closing temperatures
34.0°F
27.0°F
20.0°F
Temperatures
-0.6°F ±3°
10.0°F ±1.5°
-8.0°F ±1.5°
-17.9°F ±3°
Clockwise
1100 RPM
8.6 watts±15%@115VAC
0.11 amps± 15%@115VAC
10449510
Evaporator fan motor
Rotation (facing end opposite shaft)
RPM……………………………………
Watt…………………………………….
Clockwise
2800 RPM
5.9 ±15% watts@115VAC
12555902
Overload/Relay
12639301
Thermostat
12049801
Evaporator heater
12566301
Defrost timer
C3680310
Light switch
12466103
Light switch / Interlock
Settings
#1.......................................................
#4.......................................................
#7.......................................................
1.
Remove lens cover by removing hex head screw in lens cover. Slide cover rearward and drop down to remove.
2.
Remove damper control cover and foam insert by pulling straight down on sides of rear cover and tilt forward
approximately ½” to 1”. This will release the cover from the tabs holding it in place.
FOAM INSERT
DAMPER CONTROL COVER
3.
Ult. trip amps @ 158°F (70°C)............
Close temperature............................
Open temperature............................
Short time trip (seconds) ....................
Short time trip (amps @77°F (25°C)...
3.51 amps± 15%
142°F ±6°
257°F ±3°
10 seconds ±5
14 amps ±2amps
Volt .................................................... 120/240 VAC
Watt ................................................... 1000 watts
Current............................................... 10/5 amps
Resistance across terminals:
Above 42°F ±5°.................................. Open
Below 12°F ±7° .................................. Closed
Volt..................................................... 115 VAC
Wattage.............................................. 450 ±5% watts @ 115VAC
Resistance.........................................
29 ±5% ohms
Volt.....................................................
Defrost period (minutes)………………..
Defrost cycle (hours)……………………
Type……………………………………..
Volt………………………………………
Current…………………………………..
Release tension on damper control belt by squeezing tabs on bottom of belt tensioner to release tensioner
from it’s holding tabs.
BELT TENSIONER
4.
Damper can be removed by pushing in tabs on left and right side of damper control to release damper from
rear wall.
120VAC, 60 HZ
33 ± 3.6
8
SPST NC
125/250 VAC
8 / 6 amps
Type…………………………………….. SPDT NO/NC
Volt……………………………………… 125/250 VAC
Current………………………………….. 8 / 6 amps
RELEASE TABS
5.
6.
7.
8.
November 2001
2
12642402 Rev. 0
Install new damper in reverse order. When installing belt align large slots on belt with large cogs on damper
and control knob gear. This will synchronize control knob with damper control.
Install belt tensioner on mounting tabs and turn counter clockwise to increase tension on belt.
Reinstall damper control cover by hooking bottom on tabs and rotating up until it snaps into place.
Reinstall lens by sliding lens cover forward on tabs and installing hex head screw.
November 2001
3
12642402 Rev. 0
Download