RECEIVER DRIERS
Table of Contents
Basic Information
Receiver Driers, Accumulators and In-Line Filters are canisters used to filter
debris and remove moisture to protect the a/c system. Various inlet and outlet
fitting types and sizes are used. Many also have system protection devices,
moisture indicators, charge ports, sight glass, fuse plugs, high pressure relief
valves, mounting brackets depending on the requirements from the original
equipment manufacturer.
Receiver Driers are usually located on the high side of the a/c system before
the expansion valve. The receiver drier “receives” liquid refrigerant from the
condenser, stores it, filters out contaminates from the a/c system, and removes
moisture. A/C systems using a receiver drier use an expansion valve to control
the refrigerant flow.
Accumulators are similar to that of the receiver drier. It is usually mounted on
the low side, at the outlet of the evaporator. The accumulator “accumulates” or
stores excess refrigerant, filters and dries the refrigerant. Accumulators are used
on CCOT (Cycling Clutch Orifice Tube) or FFOT (Ford Fixed Orifice Tube)
systems. These systems use a orifice tube instead of an expansion valve to
control the refrigerant flow.
RECEIVER DRIERS
In-Line Filters are designed to be used in the liquid line in a/c systems with the
orifice tube located in the evaporator. Placing the in-line filter “up stream” of the
orifice eliminates the need to flush most systems, because the impurities are
trapped before they reach the orifice tube. These filters are designed to hold up
to 90 grams of debris, without a substantial penalty to the system’s flow. The
screens and filter pads inside the canister, catch particles and filters the
refrigerant oil.
RECEIVER DRIERS
DRIER
MEASUREMENTS
ACCUMULATORS
Specification Chart .............................................. 442
Visual Numerical Section .................................... 445
RECEIVER DRIERS
LENGTH
Specification Charts ............................................ 436
Barb Type (Push on) ........................................... 441
Block, Manifold, Pad or Slimline Type ................ 436
Flare Type ........................................................... 440
DIAMETER
In-Line Filters ...................................................... 440
O-Ring Type ........................................................ 436
Quick Disconnect Type ....................................... 439
Visual Numerical Section .................................... 445
NOTE
434
Filter Drier manufacturers have discontinued using
moisture indicators. We will supply moisture indicators
where applicable while supply lasts.
Related Items
Moisture Indicators ....................................... 444
Mounting Bracket Kits ................................... 461
O-Rings & Seals ........................................... 426
Quick Disconnect Fittings ............................. 444
Typical Drier System .................................... 441
Typical Accumulator System CCOT ............. 443
© 2011 MEI Corporation
RECEIVER DRIERS
Moisture can be harmful to air conditioning systems components and to the a/c system’s operation. For this reason, any time the a/c
system is opened, the receiver drier / accumulator needs to be replaced. A good preventative maintenance practice is to replace the
receiver drier or the accumulator and orifice tube at regular intervals or at least once per year. When replacing a compressor, the a/c
compressor manufacturer’s warranty will be void without proof of flushing the system, and also replacement of the receiver drier.
Moisture Indicator - a litmus paper device which turns colors to designate condition of the refrigerant.
Blue - Normal, Pink - Moisture in system, White - Very Wet, Grayish - oil contamination.
Manufactures have discontinued using moisture indicators. We will supply until stock is exhausted.
Pressure Relief Valve / Fuse Plug - A protection device designed to open and “bleed off” excessive pressure that may occur.
The Fuse Plug is a bi-metal device which will “melt down” to release excess pressure.
Sightglass - a “window” for observing the condition of the refrigerant.
Schrader Valve - a gauge or charge port which allows access to the system, for charging or checking the pressures.
Switch Port - Low / High Pressure Switches - a switch port allows for a male or female pressure switch to be added to the drier. If low
charge is detected, the low pressure switch opens electronically and stops the compressor operation. Similarily, as pressure increases,
the high pressure switch will dis-engage the clutch and re-engage when pressure normalizes.
Moisture indicator is not required and may not be supplied on drier.
Low / High
Pressure Switch
Quick
Disconnect
Sight
Glass
Female
O-Ring Type
Moisture
Indicator
Sight
Glass
High Pressure
Relief Valve
Slimline Manifold - Block Type
Charge/
Gauge Port
High Pressure
Relief Valve
(not required)
Moisture
Indicator
Sight
Glass
(not required)
Charge/
Gauge Port
Quick
Disconnect
Male Flare Type
(R12 only)
Pad Type
Charge/
Gauge Port
Male O-Ring
Type
Fuse
Plug
Male
O-Ring Type
High Pressure
Relief Valve
Female
Springlock Type
Female O-Ring
Type
Sight Glass
(some models)
Male
Springlock Type
Switch Port
(some models)
© 2011 MEI Corporation
TECH
TIP
Metric Schrader Valve uses green o-ring seals.
435
RECEIVER DRIERS
Typical Examples:
RECEIVER DRIERS
Listed in ascending order by Diameter x Length by Fitting Type and Size
1 5/ 8 "
2 .4"
2 1/2"
2 1/2"
2 3/4"
2.9"
3"
3"
3"
3"
3"
3"
3"
3"
4"
4"
4"
-
11-5/8"
10"
7"
10"
10"
9"
10"
10 1/4"
10 1/2"
11"
11"
11"
11"
14.35"
7"
7"
7"
-
Pad Type
Pad Type
Pad Type
PadType
Pad Type
Pad Type
Slimline #6
Slimline #6
Pad /Block
Manifold
Pad Manifold
Pad Manifold
Pad Manifold
Springlock
Block Style
Block Style
Pad Type
Pad Type
-
o-ring 0011
o-ring 0025
o-ring 0011
o-ring 0011
o-ring 0025
seals 0126
seals 0126
o-ring 0135
o-ring 0011
SL 3/8" #6
Stat Seal #8
Stat Seal #8
Stat Seal #8
o-ring 0110
Stat Seal 0131
Stat Seal 0131
o-ring 0011
o-ring 0025
o-ring 0011
o-ring 0011
o-ring 0025
seals 0126
seals 0126
o-ring 0135
o-ring 0011
SL 3/8" #6
Stat Seal #8
Stat Seal #8
Stat Seal #8
o-ring 0110
Stat Seal 0131
Stat Seal 0131
7557
7568
7547
7546
7571
7569
7197
7198
7545
7393
7397
7398
7399
7564
7559
7566
7561
7556
7585
7586
M10
(2) M10
Pressure
Relief Valve
Moisture
Indicator
Outlet
Size
Schrader
Valve
Inlet
Size
Switch
Port
TYPE
Top
(2) M10
16mm
Note
Charge
Sprinter Van 680-013634AA
R134a
CAT 176-1902
Caterpillar 113-3497
CAT 176-1902; Komatsu 20Y-979-320
Mitsubishi Fuso
3/8”-24 port; Linkbelt Exv YT54500003P1
N83-319744
R134a
use #0126 seals, N83-319534
R134a
Volvo Off-Road 11104567
R134a
Kenworth F37-6000
R134a
Peterbilt F37-6002
R134a
Peterbilt F37-6003
R134a
Peterbilt F37-6009
R134a
Ford New Holland
R134a
Frghtlnr A22-63992-000, -001
R134a
Frghtlnr A22-63994-001
R134a
A22-63993-001, A22-65550-000
R134a
Sprinter Van 2.7L, 051-03570AA
R134a
Frghtlnr 22-66700-000
R134a
Frghtlnr 22-66600-000
R134a
436
7181
7532
7513
7514
7515
7519
7524
7140
7503
7118
7120
7563
7581
7582
7600
7480
7502
7580
Top
Top
Top
Top
Top
Top
Top
3/8"
(1) M10
(1) M10
(1) M10
(1) M10
(1) M10
Top
Top
(2) Top
1/4”Male
Top
Top
Low Pressure
Switch
Bottom
Side
Top
Side
3/8” Fem
1/4” Fem
(3)
Top
Pressure
Relief Valve
Moisture
Indicator
OUTLET
FOR 3/8" #6
3/8" #6
Fine Thread
Fine Thread
M18
Fine Thread
M18
MOR 1/2"#8
MOR M20
3/8" #6
3/8" #6
QD
MIO
MIO
FOR 3/8" #6
3/8" #6
3/8" #6
MIO
Schrader
Valve
INLET
3/8" Male
3/8" #6
3/8" #6
M18
M18
M18
M18
3/8" #6
M18
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" Male
3/8" #6
3/8" #6
3/8" #6
Fuse
Plug
LENGTH
5 1/8"
5.9"
6 5/16"
6 5/16"
6 5/16"
6 5/16"
6.32"
6 3/4"
6 3/4"
8"
8"
8"
8"
8"
8"
8 1/4"
10"
-
Switch
Port
Dia.
2 1/2"
2 1/2"
2 1/2"
2 1/2"
2 1/2"
2 1/2"
2 1/2"
2 1/2"
2 1/2"
2 1/2"
2 1/2"
2 1/2"
2 1/2"
2 1/2"
2 1/2"
2 1/2"
2 1/2"
-
Sight
Glass
2 1/2" Diameter - 3/8" or M18 Male O-Ring INLET w/Various Outlets
PART
NUMBER
RECEIVER DRIERS
Dia. LENGTH
PART
NUMBER
Block, Pad, Manifold, SlimLine, or SpringLock Style Fittings
Top
Note
Internal Plug, Manifold Gskt
3/8 O’ring port; 085428-00
33-0038A
33-0382A
33-0383A
Motorhome 085686
RV218337, 085722
In-Line Design, GMC
In-Line Drier; 15982368
085268-03 (new style)
use #1430 switch
Motorhome #054-00011
085164
16mm port; 085737
Univ. Allows Std or Metric Ftgs
Bracket
RD remote condenser
Volvo 20490945
Charge
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R134a
R134a
R134a
R12/R134a
R12/R134a
R12/R134a
R134a
© 2011 MEI Corporation
RECEIVER DRIERS
Listed in ascending order by Diameter x Length by Fitting Type and Size
10"
10"
10"
10"
10"
10"
10"
10"
10"
11 3/8"
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" MIO
Top
Top
Top
Top
Top
Side
Side
Side
Top
Side
Side
1/4”Side
Side
Side
Low Pressure
Switch
Mack 221RD328
Mack 221RD327 w/binary
Side
Side
Side
Side
Side
Side
Top
Top
1/4”Side
Note
Side
Side
Top
Top
Top
Side
Pressure
Relief Valve
Moisture
Indicator
7154
7155
7155B
7156
7157
7388
7389
7390
call
7570
Schrader
Valve
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" MIO
Fuse
Plug
OUTLET
Switch
Port
LENGTH INLET
Sight
Glass
Dia.
2 3/4"
2 3/4"
2 3/4"
2 3/4"
2 3/4"
2 3/4"
2 3/4"
2 3/4"
2 3/4"
2.6"
PART
NUMBER
2 3/4" Diameter - 3/8" Male O-Ring INLET x 3/8" Male O-Ring OUTLET
w/ Trinary Switch - #1550
Kenworth K251-263
IHC1691600C92
w/ Trinary Switch - Top
Mack 221RD327, w/Binary
(2) female ports; Hino Truck
Charge
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
6"
6 1/4"
6"
6 1/2"
6 1/2"
6 1/2"
6 1/2"
6 1/2"
8”
8 1/4"
8 1/4"
8 1/4"
8 1/2"
8"
9"
9"
9"
9"
9"
9 3/4"
10"
10"
10"
10"
10"
10"
10"
10"
10"
10"
© 2011 MEI Corporation
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
7125
7124
7129
7123
7126
7127
7128
7555
7161
7133
7141
7143
7229
7180
7159
7164
7174
7185
7419
7346
7193
7132
7134
7165
7166
7175
7189
7190
7191
7567
Top
Side
Top
Top
Top
Top
Top
Top
Top
Top
Side
Top
Top
Top
Top
Top
Top
Side
Top
Top
Top
Side
Top
Top
Top
Side
Low Pressure
Switch
Pressure
Relief Valve
Moisture
Indicator
Schrader
Valve
Fuse
Plug
OUTLET
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
Switch
Port
LENGTH INLET
Note
Side
Side
Side
Side
Top
Side
Side
Top
Side
1/4" Side
Side
Side
Side
Red Dot RD5-7272-0
088423-00; 01
Binary (Side)
Trinary (Side)
N83-319634; RD5-9419-0
(2) 1/4"
Top
Top
Side
Side
Female Side
1/4" Side
Side
Top (2)
1/4" Top
Side
Side
1/4" Side
Top
Top
1/4" Top
M10 Top
Top
Side
Top
Top
Top
Top
Side
Side
Side
Top
Top
Top
Side
Side
Top
Top
Top
Top
Top
Side Includes Low Press Switch
(2) M10 x 1.25mm
1/8"-27NPT Port; 088254-01
Inlet - Right Angle
Mack 221RD44M
w/side mounting bracket
Western Star
M10 x 1.25mm
088079-00; 176237; K251-459
w/side mounting bracket
w/side mounting bracket
w/side & top mntg brkts
Western Star 088586-00
Charge
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
437
RECEIVER DRIERS
3"
3"
3"
3"
3"
3"
3"
3"
3"
3"
3"
3"
3"
3"
3"
3"
3"
3"
3"
3"
3"
3"
3"
3"
3"
3"
3"
3"
3"
3"
Sight
Glass
Dia.
PART
NUMBER
3" Diameter - 3/8" Male O-Ring INLET x 3/8" Male O-Ring OUTLET
RECEIVER DRIERS
Listed in ascending order by Diameter x Length by Fitting Type and Size
3/8"
#6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
7394
7565
7481
7232
7391
7234
Top
Top
Top
Low Pressure
Switch
Pressure
Relief Valve
Moisture
Indicator
Schrader
Valve
Fuse
Plug
Switch
Port
Sight
Glass
Top
Side
Side
Note
Charge
w/mounting bracket
Volvo RD5-6075-0
Ford Tractor E4NN-19825AA
Opposite Side Inlet
Side
Side
Top
Top
Side
Side
Side
Top
CAT# 5V5698; 8P9991
R12/R134a
R134a
R12/R134a
R12/R134a
R134a
R12/R134a
(2) 1/4"
(2) M10
(2) 1/4"
(2) 1/4"
(2) M10
Top
Top
Top
Top
Top
Side
Side
Top
Side
Side
Low Pressure
Switch
Top
Top
Top
Top
Top
Pressure
Relief
7135
7170
7172
7160
7169
Moisture
Indicator
OUTLET
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
Fuse
Plug
Schrader
Valve
LENGTH INLET
3/8" #6
8"
3/8" #6
8"
1
3/8" #6
8 / 4"
3/8" #6
10"
3/8" #6
10"
Switch
Port
Male O-Ring INLET x 3/8" Female O-Ring OUTLET
Note
Charge
R12/R134a
R12/R134a
R12
R12/R134a
R12/R134a
(M10 x 1.25mm)
Peterbilt 18-03638
similar to #7135
7387
7577
7573
7574
7575
7223
7233
7243
7572
7392
Side
Top
Top
(2) Side
(2) Side
Side/Top
Top
Low Pressure
Switch
OUTLET
3/8" #6
#6 MIO
#6 MIO
#6 MIO
3/8" #6
3/8" #6
3/8" #6
#6 MIO
3/8" #6
Pressure
Relief Valve
INLET
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" -18
3/8" #6
3/8" #6
Moisture
Indicator
LENGTH
10"
10"
11 1/2"
11 1/2"
7"
7"
7 1/2"
7 1/ 2"
7 3/4"
8 3/4"
Schrader
Valve
Female O-Ring INLET x 3/8" Male O-Ring OUTLET
NOTE
438
OUTLET
Fuse
Plug
Dia.
3"
3"
3"
3"
4"
4"
4"
4"
4"
4"
#6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
3/8" #6
Switch
Port
3/8"
3/8"
Sight
Glass
Dia.
3"
3"
3"
3"
3"
6 1/ 2 "
6 3/ 4 "
7"
7"
7 3/ 4 "
8 1/ 2 "
Sight
Glass
RECEIVER DRIERS
3/8"
LENGTH INLET
PART
NUMBER
4"
4"
4"
4"
4"
4"
PART
NUMBER
Dia.
PART
NUMBER
4" Diameter - 3/8" Male O-Ring INLET x 3/8" Male O-Ring OUTLET
Note
K251-459,K251-571,K251-566
Ford New Holland, 82012480
JDeere, RE214440
JDeere, AL163559 w/bracket
JDeere, AL162467 w/bracket
Side
Top
R12/R134a
John Deere RE49169
CASE, 86984155
JDeere AT162848; AT151981
Charge
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
Filter Drier manufacturers have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
© 2011 MEI Corporation
RECEIVER DRIERS
Listed in ascending order by Diameter x Length by Fitting Type and Size
3/ 8"
7/16"
3/ 8"
#6
#6
11/16" #6
11/16" #6
3/8" #6
#6
#6
3/8" #6
3/8" #6
3/8" #6
NOTE
7107
7131
7130
7230
7396
Top
Top
16mm
Low Pressure
Switch
Top
Pressure
Relief Valve
Fuse
Plug
Switch
Port
Top
Top
Top
Top
Note
alternate #7130; Kysor 402567
3/16" Charge Port
alternate #7131
ParkerType; IHC 1693117C1
Ford Tractor E2NN-19825AA
Side
Top
Top
Charge
R12/R134a
R12/R134a
R12/R134a
R134a
R12
RECEIVER DRIERS
8
10"
10"
10"
9"
OUTLET
11/16"
Moisture
Indicator
1/ 4"
Schrader
Valve
3"
3"
3"
3"
4"
LENGTH INLET
Sight
Glass
Dia.
Female O-Ring INLET x 3/8" Female O-Ring OUTLET
PART
NUMBER
3/8"
Filter Drier manufacturers have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
© 2011 MEI Corporation
7173
7176
7513
7514
7515
7519
7145
7563
7199
7163
7168
7179
7386
7236
Top
Top
Top
Top
Top
Low
LowPressure
Pressure
Switch
Switch
Pressure
Relief Valve
Moisture
Moisture
Indicator
Indicator
Schrader
Valve
OUTLET
QD
QD
Fine Thread
Fine Thread
M18
Fine Thread
QD
QD
QD 60mm
QD
QD
QD
QD
QD
Fuse
Plug
INLET
QD
QD
3/8" #6
M18
M18
M18
QD
3/8" Male
QD side
QD
QD
QD
QD
QD
Switch
Port
LENGTH
6"
6"
6 5/16"
6 5/16"
6 5/16"
6 5/16"
7 3 / 4"
8"
9 5 / 8"
10"
10"
10"
10"
8 1 / 2"
Sight
Glass
Dia.
2 1/ 2 "
2 1/ 2 "
2 1/ 2 "
2 1/ 2 "
2 1/ 2 "
2 1/ 2 "
2 1/ 2 "
2 1/ 2 "
3"
3"
3"
3"
3"
4"
PART
NUMBER
Quick Disconnect Type
(1) M10
(1) M10
(1) M10
(1) M10
(1) M10
Side
Side
Top
Top
Top
Top
Side
Top
(2) M10
(2) 1/4"
(2) M10
16mm
Top
Top
Top
Top
Top
Side
Side
Side
Note
In-Line; Peterbilt 18-03841
(1) M10 x 1.25mm - Top
(1) Top M10 Male
(1) M10; 33-0382A
(1) M10; 33-0383A
Motorhome 085686
Incl. orifice tube; CAT3E3535
Motorhome 054-00011
ABP N83 319524; 088470-01
2 Schrader Vlvs (1/4" Top)
(2) M10 x 1.25mm (Top)
R134a Service Port
Charge
R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R134a
R134a
R134a
R134a
R134a
R134a
R134a
R134a
439
RECEIVER DRIERS
Listed in ascending order by Diameter x Length by Fitting Type and Size
2 1/2"
2 1/2"
2 5/8"
2 3/4"
2 3/4"
3"
3"
3"
3 3/4"
4"
10"
11"
7 1/2"
8 1/2"
8 1/2"
10"
10 1/2"
11 1/2"
10 3/4"
7 1/2"
NOTE
3/8" Male O’Ring
1/2" SAE
3/8" #6 Male
1/2" Flare
1/2" #8 MIO
1/2" Flare
5/8" SAE
1/2" #8 MIO
1/2" Flare
3/8" Female O’Ring
3/8" Male O’Ring
1/2" SAE
3/8" #6 Female
1/2" Flare
1/2" #8 MIO
1/2" Flare
5/8" SAE
1/2" #8 MIO
1/2" Flare
3/8"-18 Male O’Ring
7502
7548
7562
7542
7541
7540
7551
7549
7517
7243
Moisture
Indicator
7530
7527
7525
7173
7501
7140
7503
7500
7504
7145
7560
Sight
Glass
OUTLET
3/8" compression
1/2" Female O’Ring
3/8" Male Springlock
QD
3/8" #6 Male Flare
1/2" #8 Male O’Ring
M20 Male O’Ring
1/2" Flare
1/2" Flare
QD
MIO Fitting
Side
Side
Side
Side
Side
(2) Side
Note
In-Line Filter
In-Line Filter
In-Line Filter
In-Line Drier; Peterbilt 18-03841
In-Line Drier WAH 163; 16cu.in.
In-Line Design,GMC
In-Line Drier; GMC 15982368
In-Line Drier; WLD164FO; 16cu.in.
In-Line Drier; WAH164; 16cu.in.
Enclosed Orifice; CAT# 3E3535
w/Orifice Tube, CAT# 257-3227
Charge
R12/R134a
R12/R134a
R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R134a
R134a
In-Line Drier, RD remote cond.
In-Line, Carrier WSG304; 30cu.in
16 cu.in. dessicant; Kysor 402618
In-Line Drier WSG164FO; 16cu.in
In-Line Retro; Carrier A/C; 16cu.in.
In-Line, EK304; 212-010; 30cu.in.
In-Line, Carrier WAH305; 30cu.in.
In-Line, Carrier ADK304; 30cu.in.
In-Line, TransAir AH414; 41cu.in.
In-Line Drier JDeere RE49169
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
Filter Drier manufacturers have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
4"
4"
440
7 3/4"
7"
Low Pressure
Switch
Pressure
Relief Valve
Moisture
Indicator
Schrader
Valve
Fuse
Plug
LENGTH
6 5/8"
6 3/4"
7"
8"
8"
6 1/4"
10"
Switch
Port
Dia.
2 1/2"
2 1/2"
2 1/2"
2 1/2"
2 1/2"
3"
3"
Sight
Glass
Flare End Fittings - Male INLET and Male OUTLET
PART
NUMBER
RECEIVER DRIERS
Dia.
LENGTH INLET
2 7/16"
2 11/16"
3/8" compression
2 7/16"
3"
1/2" Male Insert O’Ring
2 7/16"
5"
3/8" Female Springlock
2 1/2"
6"
QD
2 1/2"
6 3/4"
3/8" #6 Male Flare
2 1/2"
6 3/4"
3/8" #6 Male O’Ring
2 1/2"
6 3/4"
M18 Male O’Ring
2 1/2"
7"
1/2" Flare
2 1/2"
7"
1/2" Flare
2 1/2"
7 3/4"
QD
2 1/2"
7 3/4"
MIO Fitting
PART
NUMBER
In-Line Filters / Driers
INLET
OUTLET
#6 Flare
#6 Flare
#6 Flare
#6 Flare
1/2" Flare 1/2" Flare
#6 Flare
#6 Flare
#6 Flare
#6 Flare
#6 Flare
#6 Flare
1/2" Flare 1/2" Flare
7158
7501
7500
7152
7218
7124
7540
Top
Side
Top
Top
Top
Side
w/Low Pressure Sw.
w/Fuse Plug
In-Line; 30cu.in.; EK304
Charge
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
#6 Flare
#6 Flare
7235
7211
Top
Side
Side
Side
w/Fuse Plug
w/Fuse Plug
R12
R12/R134a
#6 Flare
#6 Flare
Top
Top
Note
085022-01
In-Line; 16cu.in.; WAH163
In-Line ; WLD164FO; 16cu.in.
© 2011 MEI Corporation
RECEIVER DRIERS
Listed in ascending order by Diameter x Length by Fitting Type and Size
3/ 8"
NOTE
#6
Low Pressure
Switch
Pressure
Relief Valve
Moisture
Indicator
Top
Schrader
Valve
7111
#6
Fuse
Plug
OUTLET
3/ 8"
Note
Charge
Push-on Barb
R12
Filter Drier manufacturers have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
RECEIVER DRIERS
8"
Switch
Port
LENGTH INLET
Sight
Glass
Dia.
2 1 / 2"
PART
NUMBER
Barb End Fittings (Push On)
Typical Drier System
Compressor
Expansion Valve
Drier
Condenser
© 2011 MEI Corporation
Evaporator
Thermostat
441
RECEIVER DRIERS / ACCUMULATORS
Listed in ascending order by Diameter x Length by Fitting Type and Size
RECEIVER DRIERS
Dai.
Length
Inlet
Type
Inlet
Size
Outlet
Type
Outlet
Size
PART
NUMBER
Accumulators
Note
FIOR
FOR
MIO
MOR
SL
=
=
=
=
=
Female Insert O-Ring
Female O-Ring
Male Insert O-Ring
Male O-Ring
Springlock
3"
3 7/16"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
8"
9 1/2"
8"
8"
8 1/8"
8"
8 3/4"
8 3/4"
8 7/8"
8 7/8"
9"
9"
MIO
Pad
FOR
FOR
MIO
FOR
Male SL
Male SL
Pad Type
Pad Type
FIOR
FOR
5/8" #10
M27
3/4" #12
5/8" #10
3/4" #12
5/8" #10
5/8" #10
0187
0187
1/2" #8
3/4" #12
MIO
Pad
MIO
FOR
MIO
FOR
Male SL
Male SL
FIOR
FIOR
MIO
3/4" #12
M27
3/4" #12
3/4" #12
3/4" #12
5/8" #10
3/4" #12
3/4" #12
3/4" #12
3/4" #12
7483
7415
7444
7406
7493F, G
7407
7478
7482
7496A
7496
7486
7427
(2) 1/4" Ports, Ford F4TZ-19C836A, F6TZ-19C836AA
M12 Port; Navistar 3542577C2; BOA80-323-00-139
(1) M12 Port, GM 1132722, 2724924
Universal Type Accumulator; GM 12322992
F6HZ-19C936A; 4C4H-19C808AA
Universal Type Accumulator GM
(1) 1/4" Switch Port, R12, F2UZ-19C836A, 089194-00
(1) M10 Switch Port, (1) Chg Port 13mm; F4UZ-19C836A
Ford F250/350, 6C3Z-19C836A
F81Z-19C 836AA
Ford F9UZ-19C1836AB; F65Z-19C836AA
(2) 1/4" Ports, 2724802; 3090492
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
9"
9"
9"
9"
9"
9"
9"
9"
8"
9"
9"
9"
9"
9"
9"
9"
9"
9"
9"
9"
9 1/8"
9 1/8"
9 1/8"
9 3/4"
9 3/4"
9 13/16"
10"
10"
10"
10"
11"
12"
12.3"
-
FOR
FOR
FOR
FOR
FOR
FOR
FOR
FOR
FOR
FOR
FOR
FOR
FOR
FOR
FOR
FOR
FOR
Pad Type
Male SL
Male SL
FOR
FOR
Pad Type
MIO
MOR
FOR
MOR
Female SL
MIO
MIO
MOR
Male SL
MOR
-
3/4" #12
3/4" #12
3/4" #12
3/4" #12
3/4" #12
3/4" #12
3/4" #12
M27
3/4" #12
M27
M27
M27
3/4" #12
3/4" #12
3/4" #12
M27
M27
Pad
3/4" #12
3/4" #12
1 1/16"
1 1/16"
3/4" #12
5/8" #10
1 1/16"
3/4" #12
3/8" #6
5/8" #10
5/8" #10
5/8" #10
3/4" #12
7/8"
-
MOR
MIO
MOR
MIO
MIO
MIO
MIO
MIO
MOR
MOR
MOR
MOR
MIO
MIO
MIO
MIO
MIO
MIO
Female SL
Female SL
FOR
FOR
Female SL
Female SL
FOR
MOR
Female SL
MIO
MIO
Female SL
Male SL
MOR
-
3/4" #12
3/4" #12
3/4" #12
3/4" #12
3/4" #12
3/4" #12
3/4" #12
M27
3/4" #12
M27
M27
M27
3/4" #12
3/4" #12
3/4" #12
M27
M27
M27
#10 & #12
3/4" #12
1 1/16"
1 1/16"
Pad Type
3/4" #12
5/8" #10
1 1/16"
3/4" #12
5/8" #10
3/4" #12
3/4" #12
5/8" #10
3/4" #12
7/8"
-
7428
7431
7450
7459
7462
7461
7432
7430
7434
7446
7439
7440
7447
7448
7466
7466M
7469
7457
7383
7485
7409
7543
7408
7479
7381
7544
7369
7162
7477
7454
7209
7476
7385
7416
7417
7488
7487
(2) 1/4" Ports, 1131394, 2724260
(2) 1/4" Ports; 1131506, 3059317, 27248336
(2) Serv Ports; 1131404, 2724266, 2724199, 2724804
(2) 1/4" Ports; GM 1131475, 2724877, 3057034, 3058262
(2) 1/4" Ports, GM 1131428, 2724273, 2724813
(2) 1/4" Ports, 3059108, 3092026, 3059239, 2724865
GM 1131645, 2724410, 2724411, 3092267
w/M12 Port, 13mm R134a Port; 2724885, 2724665
(1) 1/4" Port,w/R134a Port, R12 Port; 1131843; 2724689
(1) M12 Port, GM 2724817
(1) M12 Port (1) M13 Port, GM 2724902
(1) M12 Port (1) M13 Port, GM 2724847
(1) 1/4" Port, GM 2724690
(2) 1/4" Port, GM 2724194
w/M12 Port 1 3/4" below Fittings, GM 2724475
w/M12 Port 1 3/4" below Fittings, GM 2724899
(1) M12 Port (1) M13 Port, GM 2724886
(1) M12 Port (1) M13 Port, GM 15005371
(2) 1/4" Ports, E69Z-19C836B
(1) M12 Port (1) M13 Port, Ford E49Z-19C836C
Peterbilt 18-03837
Caterpillar 1018789 (steel)
Peterbilt 18-04171; 700075
(2) 1/4" Ports; Ford E6VY-19C836A
(2) 1/4" Ports; E3TZ-19C936C; E4TZ-19C836A
Caterpillar 089320-00, 197-6218
(2) R12 Ports, Ford E1VY-19C836A
Two (2) Schrader Valves: Top/Side
(2) 1/4" Ports; Ford E2TZ-19C836A
(2) 1/4" Ports, Ford E3TZ-19C836B, E7TZ-19C836A
(2) 1/4" Ports; F1TZ-19C836B
(1) 1/4" Port; E8UZ-19C836A
M12 switch port, R134a Charge Port, F4HZ-19C836A
08 Navistar Prostar 3666273-C1, 3670134-C1
Navistar Prostar 3670134-C1. P6546001
Ford F7UZ-19C836BB
Ford E75Z-19C836AA
442
© 2011 MEI Corporation
ACCUMULATORS / RECEIVER DRIERS
Listed in ascending order by Diameter x Length by Fitting Type and Size
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
3 1/2"
4"
-
Length
10 1/4"
-
Inlet
Type
Pad Type
Pad Type
Stat Seal
Pad
Pad
-
Inlet
Size
#0187
#0187
#12
-
Outlet
Type
Outlet
Size
Springlock
Stat Seal
FIOR
Stat Seal
-
#12
#12
3/4" #12
#12
-
Typical Accumulator System
7490
7494
7489
7495
7553
7552
7554
7578
call
call
7576
call
7498
7558
7583
Note
FIOR
FOR
MIO
MOR
SL
=
=
=
=
=
Female Insert O-Ring
Female O-Ring
Male Insert O-Ring
Male O-Ring
Springlock
Ford XL3Z-19C836AA
Ford XL3Z-19C836BA
Ford F75Z-19C836BA
Ford E-Series, 2C2Z-19C836BA
w/ gas eng., Ford E-Series, 5C2Z-19C836AA
w/ diesel eng., Ford E-Series, 7C2Z-19C836AA
Topkick/Kodiak 1132813 (#0142 Stat Seal)
08 Ford 8C3Z-19C836C (switch #1418)
GMC 04-06 Silverado 1411646
GMC 01-05 Silverado Avalanche 1411647
J. Deere 670D Grader AT190809, 803-465
GMC 01-05 Silverado Avalanche 1411648
F85Z-19C 836AB
GMC G Series 2003-08, 25760829
Ford E-Ser. 7C2Z-19C836B
RECEIVER DRIERS
Dai.
(continued)
PART
NUMBER
Accumulators
CCOT - Clutch Cycling Orifice Tube
Compressor
Accumulator
Orifice Tube
Evaporator
Thermostat
Condenser
© 2011 MEI Corporation
443
RECEIVER DRIERS
Quick Disconnect Fittings
3/8” female
thread
3/8” male
thread
4139
QUICK DISCONNECT COUPLER
For All Quick Disconnect Type Driers
3/8" Male x Q.D.
2 1/4” length (1 per box)
4138
QUICK DISCONNECT COUPLER
For IHC Applications
3/8" Female x Q.D. (1 per box)
RECEIVER DRIERS
Moisture Indicators
#6 = 3/8”
#8 = 1/2”
#10 = 5/8”
#12 = 3/4”
4150
3/8” Male Insert O-ring
3/8” Female O-ring
4151
3/8” Male Insert O-ring
3/8” Female O-ring
Low Pressure Switch
High Pressure Relief Valve
w/o switch use #4156
4153A
3/8” Male Insert O-ring
3/8” Female O-ring 90°
High Pressure Relief Valve
Male 7/16”-20 Switch Port
4156
3/8” Male Insert O-ring
3/8” Female O-ring
Female Switch Port
High Pressure Relief Valve
w/switch use #4151
4157
3/8” Male Insert O-ring
3/8” Female O-ring
High Pressure Relief Valve
Male Schrader Port
4158
3/8” Male Insert O-ring
3/8” Female O-ring
Switch Port (use 4155)
3/ 8”
3/ 8”
4159
Male Insert O-ring
Male Insert O-ring
4160
1/2” Male Flare
1/2” Female O-ring
7472
Heavy Duty Drier Bracket
For driers 3" in diameter
7473
Heavy Duty Compact Bracket
For driers up to 4" in diameter
Drier Brackets
7470
Strap Bracket
For driers up to 2 1/2" in diameter
444
7471
Universal Drier Bracket
For driers 2 1/4" to 3" in diameter
© 2011 MEI Corporation
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
#6 = 3/8”
#8 = 1/2”
#10 = 5/8”
#12 = 3/4”
OUT
IN
IN
7107
Dia. - 3"
Lgth. - 8 1/4"
In - 11/16" Female O-ring
Out - 3/8" Female O-ring
Top Sight Glass
7111
Dia. - 2 1/2"
Lgth. - 8"
In/Out - 3/8” x 3/8”
Top Sight Glass
Push-on Barb; R12 Only
7118
Dia. - 2 1/2"
Lgth. - 8"
3/8" x 3/8" Male O-ring
Top Sight Glass
Female Switch Port
1/4" Male Switch Port
Freightliner A22-14425-2; 085268-03
OUT
IN
IN
RECEIVER DRIERS
OUT
OUT
#1430
switch
7120
Dia. - 2 1/2"
Lgth. - 8"
In/Out - 3/8" x 3/8" Male O-ring
Top Sight Glass
Low Pressure Switch
1/4" Male Switch Port
OUT
IN
7123
Dia. - 3"
Lgth. - 6 1/2"
In/Out - 3/8” x 3/8” Male O-ring
Top Sight Glass, Side Switch Port
P.R.V. & Moisture Indicator
OUT
IN
7125
Dia. - 3"
Lgth. - 6"
In/Out - 3/8" x 3/8" Male O-ring
Top Sight Glass, Side Switch Port
High Pressure Reliev Valve
7126
Dia. - 3"
Lgth. - 6 1/2"
In/Out - 3/8" x 3/8" Male O-ring
Top Sight Glass, Side 1/4” Schrader Valve
High Pressure Relief Valve
OUT
IN
IN
7128
Dia. - 3"
Lgth. - 6 1/2"
In/Out - 3/8" x 3/8" Male O-ring
Top Sight Glass
Side Trinary Switch, Fuse Plug
© 2011 MEI Corporation
OUT
7129
Dia. - 3"
Lgth. - 6"
In/Out - 3/8" x 3/8" Male O-ring
Top Sight Glass, Fuse Plug
7124
Dia. - 3"
Lgth. - 6 1/4"
In/Out - 3/8" x 3/8" Male Flare
Top Sight Glass, Fuse Plug
OUT
IN
7127
Dia. - 3"
Lgth. - 6 1/2"
In/Out - 3/8" x 3/8" Male O-ring
Top Sight Glass
Side Binary Switch, Fuse Plug
IN
OUT
7130
Dia. - 3"
Lgth. - 10"
In - 11/16" Female O-ring
Out - 3/8" Female O-ring
Top Sight Glass
Pressure Relief Valve
445
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
IN
OUT
IN
#6 = 3/8”
OUT
7132
Dia. - 3"
Lgth. - 10"
In/Out - 3/8" x 3/8"
Male O-ring
Side Sight Glass
Top Schrader Valve
Moisture Indicator
Pressure Relief Valve
7131
Dia. - 3”
Lgth. - 10”
In - 7/16” Female O-ring
Out - 3/8” Female O-ring
Top Sight Glass
Charge Port 3/16”
Moisture Indicator; PRV
#8 = 1/2”
#10 = 5/8”
OUT
#12 = 3/4”
IN
7133
Dia. - 3"
Lgth. - 8 1/4"
In/Out - 3/8" x 3/8"
Male O-ring
Top Sight Glass
Top Switch Port
Pressure Relief Valve
OUT
RECEIVER DRIERS
IN
OUT
7134
Dia. - 3"
Lgth. - 10"
In/Out - 3/8" x 3/8" Male O-ring
Top Sight Glass
Top Switch Port
Moisture Indicator
Pressure Relief Valve
OUT
OUT
7135
Dia. - 3" Lgth. - 8"
In - 3/8" Male O-ring
Out - 3/8"Female O-ring
Top Sight Glass
(2) Schrader Valves
Moisture Indicator
Pressure Relief Valve
7141
Dia. - 3"
Lgth. - 8 1/4"
In/Out - 3/8" x 3/8" Male O-ring
Side Sight Glass, Top Switch Port
IN
OUT
7143
Dia. - 3"
Lgth. - 8 1/4"
In/Out - 3/8" x 3/8" Male O'ring
Top Sight Glass, Schrader Valve
Fuse Plug, Moisture Indicator
OUT
IN
7145
Dia. - 2 1/2"
Lgth. - 7 3/4" (13.88" OAL)
Quick Disconnect
Enclosed Orifice Tube
R134a Only
CAT 3E3535
OUT
IN
IN
7152
Dia. - 2 1/2"
Lgth. - 8"
In/Out - 3/8" x 3/8" Male Flare
Top Sight Glass
446
7140
Dia. - 2 1/2"
Lgth. - 6 3/4"
In - 3/8" Male O-ring
Out - 1/2" Male O-ring
In-Line Design, GMC
IN
IN
OUT
IN
7154
Dia. - 2 3/4"
Lgth. - 10"
In/Out - 3/8" x 3/8" Male O-ring
Top Sight Glass
Side Low Pressure Switch
Pressure Relief Valve
7155
Dia. - 2 3/4"
Lgth. - 10"
In/Out - 3/8" x 3/8" Male O-ring
Top Sight Glass
Side 1/4” Schrader Valve
Pressure Relief Valve
Mack 221RD328
© 2011 MEI Corporation
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
#6 = 3/8”
#8 = 1/2”
#10 = 5/8”
#12 = 3/4”
1510
OUT
Mack
221RD327
7156
Dia. - 2 3/4"
Lgth. - 10"
In/Out - 3/8" x 3/8" Male O-ring
Top Sight Glass
Side Switch Port
Pressure Relief Valve
IN
OUT
OUT
IN
7158
Dia. - 2 1/2"
Lgth. - 6 5/8"
In/Out - 3/8" x 3/8" Male Flare
w/ Fuse Plug
Top Sight Glass
7157
Dia. - 2 3/4"
Lgth. - 10"
In/Out - 3/8" x 3/8" Male O-ring
Top Sight Glass
Side Trinary Switch
Pressure Relief Valve
IN
085022-01
7159
Dia. - 3"
Lgth. - 9"
In/Out - 3/8" x 3/8"
Male O-ring
Top Sight Glass
Top Schrader Valve
Moisture Indicator
Pressure Relief Valve
OUT
7160
Dia. - 3"
Lgth. - 10"
In - 3/8" Male O-ring
Out - 3/8" Female O-ring
Top Sight Glass
(2) Schrader Valves
Moisture Indicator
Pressure Relief Valve
ABPN83-319714
IN
IN
OUT
7161
Dia. - 3"
Lgth. - 8"
In/Out - 3/8" x 3/8" Male O-ring
Top Sight Glass
(2) Schrader Valves
Fuse Plug
IN
OUT
7164
Dia. - 3"
Lgth. - 9"
In/Out - 3/8" x 3/8" Male O-ring
Top Sight Glass
Pressure Relief Valve
Side Switch Port (1/8”-27 NPT)
Moisture Indicator
088254-01
© 2011 MEI Corporation
7162
Accumulator
Dia. - 3 1/2"
Lgth. - 10"
In - 3/8” Female Springlock
Out - 5/8” Female Springlock
(2) Schrader Vlv (Top/Side)
IN
OUT
7165
Dia. - 3"
Lgth. - 10"
In/Out - 3/8" x 3/8" Male O-ring
Top Sight Glass
Schrader Valve
Pressure Relief Valve
7163
Dia. - 3"
OUT
Lgth. - 10"
Quick Disconnect
Top Sight Glass
(2) 1/4” Schrader Valves
Moist Indicator; R134a Only
IN
OUT
7166
Dia. - 3"
Lgth. - 10"
In/Out 3/8" x 3/8" Male O-ring
Top Sight Glass
Pressure Relief Valve
Moisture Indicator
Metric Schrader Valve - M10
447
RECEIVER DRIERS
7155B
Dia. - 2 3/4”
Lgth. - 10”
3/8” x3/8” Male O’’Ring with
Male Switch Port, Fuse
Plug, & Top Sight Glass,
supplied w/Binary Switch
1550
IN
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
#6 = 3/8”
#8 = 1/2”
#10 = 5/8”
#12 = 3/4”
OUT
IN
7168
IN
Dia. - 3"
Lgth. - 10"
Quick Disconnect
Top Sight Glass
(2) Schrader Valves - M10
Moisture Indicator; R134a Only
OUT
7169
Dia. - 3"
Lgth. - 10"
In - 3/8" Male O-ring
Out - 3/8" Female O-ring
Top Sight Glass
Pressure Relief Valve
(2) Schrader Valves - M10
IN
OUT
7170
Dia. - 3"
Lgth. - 8"
In - 3/8" Male O-ring
Out - 3/8" Female O-ring
Top Sight Glass
Pressure Relief Valve
Moisture Indicator
(2) Schrader Valves - M10
OUT
RECEIVER DRIERS
OUT
IN
7172
Dia. - 3'"
Lgth. - 8 1/4"
In - 3/8" Male O’ring
Out - 3/8" Female O'ring
Top Sight Glass
High Pressure Relief Valve
(2) Schrader Valves - R12 Only
7173
In-Line Drier - R134a Only
Dia. - 2 1/2"
Lgth. - 6" (9.6” overall)
Quick Disconnect
Peterbilt oe# 18-03841
7174
Dia. - 3"
Lgth - 9"
In/Out 3/8" x 3/8" Male O-ring
Pressure Relief Valve
Moisture Indicator
OUT
IN
OUT
OUT
7175
Dia. - 3"
Lgth. - 10"
In/Out - 3/8" x 3/8" Male
Side Sight Glass
Kenworth oe# K251-459
OUT
IN
IN
7176
Dia. - 2 1/2"
Lgth - 6"
Quick Disconnect
Top Sight Glass
(1) Schrader Valve - M10
IN
7179
IN
Dia. - 3"
Lgth. - 10"
Quick Disconnect
Top Sight Glass
Pressure Relief Valve
R134a Service Port 16mm
OUT
IN
7180
Dia. - 3"
Lgth. - 8"
In/Out - 3/8" x 3/8" Male O-ring
(2) Schrader Valves - M10 PH088340-01
448
7181
Dia. - 2 1/2"
Lgth. - 5 1/8"
Top Sight Glass
Manifold/Gasket
Internal Fuse Plug
7185
Dia. - 3"
Lgth. - 9"
3/8" x 3/8" Male O-ring
Inlet - Right Angle
Moisture Indicator
Pressure Relief Valve
© 2011 MEI Corporation
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
IN
IN
#6 = 3/8”
#8 = 1/2”
#10 = 5/8”
#12 = 3/4”
OUT
OUT
7189
Dia. - 3"
Lgth. - 10"
In/Out - 3/8" x 3/8"
Male O-ring
Top Sight Glass
Moisture Indicator
7190
Dia. - 3"
Lgth. - 10"
In/Out - 3/8" x 3/8"
Male O-ring
Top Sight Glass
Moisture Indicator
7191
Dia. - 3"
Lgth. - 10"
In/Out - 3/8" x 3/8"
Male O-ring
Top Sight Glass
OUT
OUT
IN
OUT
IN
RECEIVER DRIERS
IN
# 0126
7193
Dia. - 3”
Lgth. - 10”
In - 3/8” Male O-ring
Out - 3/8” Male O-ring
Top Sight Glass
Fuse Plug, (1) 1/4” Port
Western Star
seals
7197
# 0126
seals
Dia. - 3"
Lgth. - 10"
In/Out - #6 Slimline
Slimline use #0126 seals
(2) M10 Switch Ports
Pressure Relief Plug
ABPN83-319744
7198
Dia. - 3”
Lgth. - 10 1/4”
In/Out - 3/8” x 3/8”
Slimline use #0126 seals
(2) M10 Switch Ports
R134a Only
ABPN83-319534
OUT
IN
OUT
IN
7199
Dia. - 3”
Lgth. - 9 5/8”
In - QD (side)
Out - QD (top)
(2) M10 Ports, Sight Glass
Quick Disconnect - 60mm (2 3/8”)
ABPN83-319524; 088470-01
7209
Ford Accumulator
Dia. - 3 1/2”
Lgth. - 11”
In - 5/8" Male O-ring
Out - 5/8" Female Springlock
(2) 1/4” Ports
F1TZ-19C836B
7211
Dia. - 4"
Lgth. - 7"
In/Out - 3/8" x 3/8"
Male Flare
Side Sight Glass, Fuse Plug
OUT
IN
OUT
IN
7218
Dia. - 2 1/2"
Lgth. - 8"
In/Out - 3/8" x 3/8" Male Flare
Top Sight Glass
Top Schrader Valve
Low Pressure Switch
© 2011 MEI Corporation
7223
Dia. - 4"
Lgth. - 7"
In - 3/8" Female O-ring
Out - 3/8" Male O-ring
Top Sight Glass
Side Fuse Plug
449
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
IN
OUT
OUT
#6 = 3/8”
#8 = 1/2”
#10 = 5/8”
#12 = 3/4”
IN
OUT
7229
Dia. - 3"
Lgth. - 8 1/2"
In/Out 3/8" x 3/8" Male O-ring
Top Sight Glass
Male Schrader Port
Female Switch Port
Low Pressure Switch
Pressure Relief Valve
IN
7232
Dia. - 4"
Lgth. - 7"
In/Out - 3/8" x 3/8"
Male O-ring
(opposite side inlet)
Top Sight Glass
Side Fuse Plug
7230
Dia. - 3"
Lgth. - 10"
In - 11/16" Female O-ring
Out - 3/8" Female O-ring
Top Sight Glass
Pressure Relief Valve
16mm Service Port; R134a Only
OUT
RECEIVER DRIERS
OUT
7233
Dia. - 4"
Lgth. - 7 1/2"
In - 3/8" Female O’ring
Out - 3/8" Male O'ring
(2) Side Sight Glass
IN
7234
Dia. - 4"
Lgth. - 8 1/2"
In/Out - 3/8" x 3/8"
Male Insert O-ring
Combo: Sight Glass and
Moisture Indicator,
Low Pressure Switch
Port, Sided Fuse Plug
CAT 5V5698,
8P9991
IN
7235
Dia. - 4"
Lgth. - 7 3/4"
In/Out - 3/8" x 3/8"
Male Flare
Top Sight Glass
Fuse Plug, R12
IN
OUT
7236
Dia. - 4"
Lgth. - 8 1/2"
Quick Disconnect
Top Sight Glass
Moisture Indicator
Low Pressure Switch
Pressure Relief Valve; R134a Only
OUT
IN
7243
Dia. - 4 "
Lgth. - 7 1/2"
In - 3/8” Female O-ring
Out - 3/8" -18 Male O-ring
(2) Side Sight Glasses
John Deere RE49169
IN
7346
Dia. - 3"
Lgth. - 9 3/4"
In/Out - 3/8" x 3/8"
Male O-ring
Sight Glass
OUT
OUT
7369
Accumulator Ford
Dia. - 3 1/2”
Lgth. - 10”
In - 3/4” Male O-ring
Out - 3/4” Male O-ring
(2) R12 Ports
450
E1VY-19C836A
7381
Accumulator Ford
Dia. - 3 1/2”
Lgth. - 9 3/4”
In - 5/8” Male O-ring
Out - 5/8” Female Springlock E3TZ-19C936C,
(2) 1/4” Ports
E4TZ-19C936A
IN
7383
Accumulator Ford
Dia. - 3 1/2”
Lgth. - 9”
In - 3/4” Male Springlock
Out - 3/4” and 5/8” Female Springlock
(2) 1/4” Ports
E69Z-19C836B
© 2011 MEI Corporation
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
#6 = 3/8”
#8 = 1/2”
#10 = 5/8”
#12 = 3/4”
OUT
OUT
OUT
089248-00,
F4HZ-19C836A
IN
7388
Dia. - 2 3/4"
Lgth. - 10"
In/Out - 3/8" x 3/8" Male O-ring
Side Sight Glass
Top Switch Port
Pressure Relief Valve
Kenworth K251-263
7386
IN
Dia. - 3"
Lgth. - 10"
Quick Disconnect
Side Sight Glass
Moisture Indicator; R134a Only
OUT
IN
7387
Dia. - 3"
Lgth. - 10"
In - 3/8" Female O-ring
Out - 3/8" Male O-ring
Moisture Indicator
Side Sight Glass
Kenworth K251-566
IN
7389
Dia. - 2 3/4"
Lgth. - 10"
In/Out - 3/8" x 3/8" Male O-ring
Side Sight Glass
Top Schrader Valve
Pressure Relief Valve
IHC OE# 1691600C92
OUT
RECEIVER DRIERS
7385
Accumulator
Dia. - 3 1/2”
Lgth. - 12.3”
In/Out - 7/8” Male O-ring
M12 Switch Port,
R134a Charge Port
IN
7390
Dia. - 2 3/4"
Lgth. - 10"
In/Out - 3/8" x 3/8" Male O-ring
Side Sight Glass
Top Trinary Switch
Pressure Relief Valve
OUT
OUT
IN
OUT
IN
IN
7391
Dia. - 4"
Lgth. - 7 3/4"
In/Out - 3/8" x 3/8"
Male O-ring
Top Sight Glass
Moisture Indicator
Side Low Pressure Switch
Pressure Relief Valve; R134a Only
# 0011
7392
Dia. - 4"
Lgth. - 8 3/4"
In - 3/8" Female O-ring
Out - 3/8" Male O-ring
Top Sight Glass and
Side Sight Glass
Moisture Indicator
o-rings
John Deere
AT151981,
AT162848
7393
Dia. - 3”
Lgth. - 11”
Manifold connection type
R134a Only
Kenworth T2000, F37-6000
IN
IN
7394
Dia. - 4"
Lgth. - 6 1/2”
In/Out - 3/8" x 3/8"
Male O-ring
Top Sight Glass
Side Fuse Plug
© 2011 MEI Corporation
7395
Dia. - 4"
Lgth. - 7 3/4"
In - 3/8" Male O-ring
Out - 3/8" Female O-ring
OUT
7396
Dia. - 4”
Lgth. - 6”
OUT
Horizontal Type
3
In - /8” Female Piloted O-ring Fitting
Out - 3/8” Female Piloted O-ring Fitting
451
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
7397
Dia. - 3”
Lgth. - 11”
Pad Manifold Fittings
330, 340, 387 Series
PETERBILT F37-6002
#6 = 3/8”
7398
Dia. - 3”
Lgth. - 11”
Pad Manifold Fittings
365 thru 389 Series
PETERBILT F37-6003
#8 = 1/2”
#10 = 5/8”
#12 = 3/4”
7399
Dia. - 3”
Lgth. - 11”
Pad Manifold Fittings
PETERBILT F37-6009
OUT
IN
RECEIVER DRIERS
IN
7400
Side Sight Glass
Bottom High Press Switch
Top Moisture Indicator
CARRIER 65-00193-00; 088599-01
IN
7406
Universal Accumulator
Dia. - 3 1/2”
Lgth. - 8”
In - 3/4” #12 Female O-ring
Out - 3/4” #12 Female O-ring
(2) R12 Ports
OUT
GM
12322992
7407
Universal Accumulator
Dia. - 3 1/2”
Lgth. - 8”
In - 3/4” #12 Female O-ring
Out - 3/4” #12 Female O-ring
(2) R12 Ports
IN
IN
# 0017
o-rings
# 0137
suction o-ring
7408
Accumulator
Dia. - 3 1/2”
Lgth. - 9 1/8”
uses (2) #0017 o-rings
and #4589SR fitting
OUT
OUT
Peterbilt Pad
18-04171
7409
Dia. - 3 1/2”
Lgth. - 9 1/8”
In - 1 1/16” Female O-ring
Out - 1 1/16” Female O-ring
Peterbilt 18-03837
OUT
# 0139
suction
flange gasket
7415
M12
Dia. - 3 7/16”
Lgth. - 9 1/2”
Pad Mount Accumulator
(1) M12 Port
Navistar 3542577C2;
BOA80-323-00-139
IN
# 0136
uses 1400 sensor
OUT
# 0136
discharge o-ring
discharge o-ring
# 0138
# 0138
discharge
flange gasket
discharge
flange gasket
# 0011
#6 o-ring
7416
Accumulator Assy.
2008 Navistar Prostar
3666273-C1
452
# 0011
#6 o-ring
7417
Accumulator
Navistar Prostar 3670134-C1, P6546001
7419
Dia. - 3”
Lgth. - 9”
Mack 221RD44M
© 2011 MEI Corporation
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
#6 = 3/8”
#8 = 1/2”
#10 = 5/8”
#12 = 3/4”
OUT
OUT
OUT
IN
IN
7427
Accumulator GM
Dia. - 3 1/2”
Lgth. - 9”
In - 3/4” Female O-ring
Out - 3/4” Male O-ring
(2) 1/4” Ports
IN
2724802,
3090492
7428
Accumulator GM
Dia. - 3 1/2”; Lgth. - 9”
In - 3/4” Female O-ring
Out- 3/4” Male O-ring
(2) 1/4” Ports
1131394,
2724260
7430
Accumulator GM
Dia. - 3 1/2”; Lgth. - 9”
In - M27 x 2 5/8" Female O-ring
Out - M27 x 2 5/8" Male Insert O-ring 2724665,
(1) M12 Port; (1) M13 R134a Port
2724885
IN
OUT
IN
OUT
7431
Accumulator GM
Dia. - 3 1/2”; Lgth. - 9”
In - 3/4” Female O-ring
Out - 3/4” Male Insert O-ring
(2) 1/4" Ports
IN
1131506,
3059317
7432
Accumulator GM
Dia. - 3 1/2”; Lgth. - 9”
In - 3/4” Female O-ring
Out - 3/4” Male Insert O-ring
2724411,
3092267
7434
Accumulator GM
Dia. - 3 1/2”; Lgth. - 8”
In - 3/4” Female O’ring
Out- 3/4” Male O’ring
(1) 1/4" Port
1131843,
2724542,
2724689
IN
IN
OUT
OUT
7439
Accumulator GM
Dia. - 3 1/2”; Lgth. - 9”
In -M27 Female O-ring
Out -M27 Male O-ring
(1) M12 Port; (1) M13 R134a Port
OUT
2724902
IN
7440
Accumulator GM
Dia. - 3 1/2”; Lgth. - 9”
In -M27 Female O-ring
Out -M27 Male O-ring
(1) M12 Port; (1) M13 R134a Port
OUT
IN
2724847
7444
Accumulator GM
Dia. - 3 1/2”; Lgth. - 8”
In -M27 Female O-ring
Out -M27 MIO
(1) M12 Port
1132722,
2724924
IN
IN
OUT
7446
Accumulator GM
Dia. - 3 1/2”; Lgth. - 9”
In -M27 Female O-ring
Out -M27 Male O-ring
(1) M12 Port
© 2011 MEI Corporation
OUT
2724817
7447
Accumulator GM
Dia. - 3 1/2”; Lgth. - 9”
In - 3/4” Female O-ring
Out - 3/4” Male Insert O-ring
(1) 1/4” Port
2724690
7448
Accumulator GM
Dia. - 3 1/2”; Lgth. - 9”
In - 3/4” Female O-ring
Out - 3/4” Male Insert O-ring
(2) 1/4” Ports
2724194
453
RECEIVER DRIERS
OUT
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
#6 = 3/8”
#8 = 1/2”
#10 = 5/8”
#12 = 3/4”
IN
OUT
OUT
# 0142
seals
IN
7450
Accumulator GM
Dia. - 3 1/2”; Lgth. - 9”
In - 3/4” Female O-ring
Out - 3/4” Male O-ring
(2) 1/4” Ports
7454
Accumulator Ford
Dia. - 3 1/2”; Lgth. - 10”
In - 5/8” Male Insert O-ring
Out - 3/4” Male Insert O-ring
2724804 (2) 1/4” Ports
E7TZ-19C836A
7457
Accumulator GM
Dia. - 3 1/2”; Lgth. - 9”
In - Pad Type
Out - M27 Male Insert O-ring
(1) M12 Port
(1) M13 R134a Port
15005371
RECEIVER DRIERS
IN
IN
OUT
OUT
7459
Accumulator GM
Dia. - 3 1/2”; Lgth. - 9”
In - 3/4” Female O-ring
Out - 3/4” Male Insert O-ring
(2) 1/4” Ports
2724877
OUT
7461
Accumulator GM
Dia. - 3 1/2”; Lgth. - 9”
In - 3/4” Female O'ring
Out - 3/4” Male Insert O-ring
(2) 1/4” Ports
2724865
IN
7462
Accumulator GM
Dia. - 3 1/2”; Lgth. - 9”
In - 3/4” Female O-ring
Out - 3/4” Male Insert O-ring
(2) 1/4” Ports
IN
2724273,
2724813
OUT
IN
OUT
IN
OUT
7466
Accumulator GM
Dia. - 3 1/2”
Lgth. - 9”
In - 3/4” Female O-ring
Out - 3/4” Male Insert O-ring
(1) M12 Port (1 3/4” below fittings)
2724475
7466M
Accumulator GM
Dia. - 3 1/2”
Lgth. - 9”
In - M27 Female O-ring
Out - M27 Male Insert O-ring
(1) M12 Port (1 3/4” below fittings)
2724899
7469
Accumulator GM
Dia. - 3 1/2”
Lgth. - 9”
In - M27 Female O-ring
Out - M27 Male Insert O-ring
(1) M12 Port; (1) M13 R134a Port
2724886
OUT
#10
Male
IN
7476
Accumulator Ford
Dia. - 3 1/2”
Lgth. - 12”
In - 3/4” Male Springlock
Out - 3/4” Male Springlock
(1) 1/4” Port
454
E8UZ-19C836A
7477
Accumulator Ford
Dia. - 3 1/2”
Lgth. - 10”
In - 5/8” Male Insert O-ring
Out - 3/4” Male Insert O-ring
(2) 1/4” Ports
E2TZ-19C836A
7478
Accumulator Ford
Dia. - 3 1/2”
Lgth. - 8 3/4”
In/Out - 5/8” Male Springlock
089194-00,
1/4” Switch Port, R12
F2UZ-19C836A
© 2011 MEI Corporation
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
#6 = 3/8”
OUT
#8 = 1/2”
#10 = 5/8”
#12 = 3/4”
IN
IN
OUT
IN
7480
Dia. - 2 1/2”
Lgth. - 8 1/4”
In/Out - 3/8" x 3/8" Male O-ring
Top Sight Glass, Switch Port
7481
Dia. - 4”
Lgth. - 7”
In - 3/8” Male O-ring
Out - 3/8” Male O-ring
Fuse Plug; Bracket
7482
Accumulator Ford
Dia. - 3 1/2”
Lgth. - 8 3/4”
In - 5/8” #10 Male Springlock
Out - 3/4” #12 Male Springlock
(1) M10 Switch Port
(1) 13mm Chg Port
F4UZ-19C836A
7483
Accumulator Ford
Dia. - 3”
Lgth. - 8”
In - 5/8” Male Insert O-ring
Out - 3/4” Male Insert O-ring F4TZ-19C836A
(2) 1/4” Ports
F6TZ-19C836AA
7485
Accumulator Ford
Dia. - 3 1/2”
Lgth. - 9”
In - 3/4” Male Springlock
Out - 3/4” Female Springlock
(1) M12 Port
(1) M13 R134a Port
7486
Accumulator Ford
Dia. - 3 1/2”
Lgth. - 9”
In - 1/2” #8 Female Insert O’ring
Out - 3/4” #12 Female Insert O’ring
F65Z-19C836AA
7487
Accumulator Ford
F75Z-19C836AA
7488
Accumulator
Ford F-Series
F7UZ-19C836BB
Ford Tractor
E4NN-19825AA
E49Z-19C836C
# 0187
pad o-ring
7489
Accumulator Ford
F75Z-19C836BA
© 2011 MEI Corporation
7490
Accumulator Ford
XL3Z-19C836AA
7493F
O.E. Style
Ford Accumulator
Dia. - 3 1/2”
Lgth. - 8 1/8”
In - 5/8” #10 MIO
Out - 3/4” #12 MIO
F6HZ-19C836A,
F7HH-19E647AB,
4C4H-19C808AA
455
RECEIVER DRIERS
7479
Accumulator Ford
Dia. - 3 1/2”
Lgth. - 9 3/4”
In - 3/4” Male Insert O-ring
Out - 3/4” Female Springlock
(2) 1/4” Ports
E6VY-19C836A
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
7493G
Aftermarket Style
Ford Accumulator
Dia. - 3 1/2”
Lgth. - 8 1/8”
In - 5/8” #10 MIO
Out - 3/4” #12 MIO
F6HZ-19C836A
#6 = 3/8”
#8 = 1/2”
#10 = 5/8”
7494
Accumulator Ford
XL3Z-19C836BA
7495
Accumulator
Ford Truck E Series
2C2Z-19C836BA
# 0187
7496A
pad o-ring
Accumulator
(includes plastic housing)
Dia. - 3 1/2”
Lgth. - 8 7/8"
Ford F250/350
6C3Z-19C836A
7498
Accumulator Ford
Dia. - 4"
Lgth. - 10 1/4"
In - PAD
Out - 3/4” #12 Female Insert O’ring
F85Z-19C836AB
#12 = 3/4”
RECEIVER DRIERS
Plastic housing not included.
Must reuse old housing or use
PlP
#7496A which includes the
housing.
# 0187
pad o-ring
7496
Accumulator Ford
Dia. - 3 1/2”
Lgth. - 8 7/8"
In - PAD
Out - 3/4” #12 Female Insert O’ring
F81Z-19C836AA
OUT
OUT
# 0170
special o-rings
(supplied)
7501
Dia. - 2 1/2"
Lgth. - 6 3/4"
In/Out - 3/8" x 3/8" Male Flare
16 cu.in. In-Line Filter Drier
WAH163
7500
Dia. - 2 1/2"
Lgth. - 7"
In/Out - 1/2" x 1/2" Male Flare
16 cu.in. In-Line Filter Drier
WAH164FO
IN
7502
Dia. - 2 1/2"
Lgth. - 10"
In/Out - 3/8" x 3/8"
Male O-ring
Red Dot remote condenser
IN
OUT
OUT
# 0077
fine thread
check valve
o-ring
7503
Dia. - 2 1/2"
Lgth. - 6 3/4"
M18 Inlet x M20 Outlet
Male O-ring
In-line Design, GMC 15982368
456
IN
7504
Dia. - 2 1/2"
Lgth. - 7"
In/Out - 1/2" x 1/2" Male Flare
16 cu. in. In-Line Drier
WAH 164
IN
# 0011
o-ring
7513
Dia. - 2 1/2"
Lgth. - 6 5/16"
In - 3/8" Male O-ring
Out - Fine Thread
(1) M10 Port; Top Sight Glass
33-0038A
© 2011 MEI Corporation
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
OUT
#6 = 3/8”
#8 = 1/2”
#10 = 5/8”
#12 = 3/4”
OUT
fine thread
check valve
IN
IN
7514
Dia. - 2 1/2"
Lgth. - 6 5/16"
In - M18 Male
Out - Fine Thread
(1) M10 Port; Top Sight Glass
OUT
33-0382A
IN
7515
Dia. - 2 1/2"
Lgth. - 6 5/16"
In - M18 Male
Out - M18 Male
(1) M10 Port; Top Sight Glass
OUT
33-0383A
7517
Dia. - 3 3/4”
Lgth. - 10 3/4"
In/Out - 1/2" x 1/2" Male Flare
41 ci.in. dessicant
TYPE AH414 In-LineDrier/TransAir A/C
IN
OUT
IN
7519
Dia. - 2 1/2"
Lgth. - 6 5/16"
In - M18 Male
Out - Fine Thread
M10 Switch Port
GM Chasis Motor Home#
085686
7524
Dia. - 2 1/2"
Lgth. - 6.32"
In/Out - M18 Male
M10 Switch Port
Top Sight Glass
085722,
RV218337
RECEIVER DRIERS
fine thread
check valve
7525
Dia. - 2 7/16”
Lgth. - 5”
In - 3/8" Female Springlock
Out - 3/8" Male Springlock
Ideal for adding In-Line Filter to Ford
Spring Lock Liquid A/C Line.
OUT
IN
OUT
OUT
IN
IN
#0011
o-rings
7527
Dia. - 2 7/16”
Lgth. - 3”
In - 1/2” Male Insert O'ring
Out - 1/2” Female O'ring
Ideal for adding In-Line Filter to
Liquid A/C Line.
7532
Dia. - 2 1/2"
Lgth. - 5.9"
3/8" x 3/8" Male O-ring
Top Sight Glass
Side Fuse Plug
Port 3/8" O’Ring
7530
In/Out - 3/8” x 3/8” Compression
Dia. - 2 7/16”
Lgth. - 2 11/16”
IN
OUT
uses #0013 o-rings
7540
Dia. - 3”
Lgth. - 10”
In/Out 1/2" x 1/2" Male Flare
30 cu.in. In-Line Filter Drier
© 2011 MEI Corporation
EK 304
7541
Dia. - 2 3/4"
Lgth. - 8 1/2"
In/Out - 1/2" x 1/2" Male Insert O'ring
16 cu.in. In-Line Filter Drier w/sight glass
CARRIER #14-00288-00; WSG 164 MIO
085428-00
IN
OUT
supplied with special
#0170 o-rings
7542
Dia. - 2 3/4”
Lgth. - 8 1/2”
In/Out - 1/2" x 1/2" Flare O’ring
16 cu.in.In-Line Drier w/sight glass
WSG164 FO
457
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
#6 = 3/8”
#8 = 1/2”
#10 = 5/8”
#12 = 3/4”
OUT
IN
IN
# 0017
# 0017
o-rings
o-rings
7543
Accumulator
Dia. - 3 1/2”
Lgth. - 9 1/8”
In - 1 1/16” Female O-ring
Out - 1 1/16” Female O-ring
CAT OE# 1018789 (Steel)
# 0135
o-ring
7544
Accumulator
Dia. - 3 1/2"
Lgth. - 9 13/16"
In - 1 1/16” Female O-ring
Out - 1 1/16” Female O-ring
CAT OE# 089320-00; 197-6218
OUT
7545
Dia. - 3"
Lgth. - 10 1/2"
Pad Type Drier
with 16mm port
VOLVO OFF-ROAD OE# 11104567
RECEIVER DRIERS
IN
# 0011
# 0011
o-ring
o-rings
7546
Dia. - 2 1/2"
Lgth. - 10"
Pad Type Drier
KUBOTA 3F999-10740
Komatsu 20Y-979-320
CATERPILLAR 176-1902
IN
7547
Dia. - 2 1/2"
Lgth. - 7"
Pad Type Drier
CATERPILLAR 113-3497
OUT
IN
OUT
7548
Dia. - 2 1/2"
Lgth. - 11"
30 cu. in. In-Line Filter Drier w/sight glass
In/Out - 1/2” SAE; Carrier WSG304
OUT
# 0013
o-ring
7549
Dia. - 3"
Lgth. - 11 1/2"
30 cu. in. In-line Filter Drier w/sight glass
In/Out - 1/2” Male Insert O’ring
Carrier ADK304, WSG304MOI
7551
Dia. - 3"
Lgth. - 10 1/2"
30 cu. in. In-line Filter Drier
In/Out - 5/8” SAE
Carrier WAH305
7552
Accumulator Ford
2011-2007 E-Series w/diesel engine
7C2Z-19C836AA
IN
7553
Accumulator Ford
2006-2004 E-Series w/gas engine
2C2Z-19C836AA, 5C2Z-19C836AA
458
7554
Accumulator
2006-2003 Topkick/Kodiak
oe# 1132813
(uses #0142 Stat Seal Sealing Washer)
OUT
7555
Dia. - 3"
Lgth. - 6 1/2"
In/Out - 3/8” x 3/8” Male O’Ring
Top Sight Glass,
P.R.V. & Moisture Indicator RD5-9419-0
© 2011 MEI Corporation
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
#6 = 3/8”
#8 = 1/2”
# 0110
# 0011
# 0142
o-ring
o-ring
#12 stat seal
7557
Dia. - 1 5/8"
Lgth. - 11 5/8"
Pad Style Drier
2007-08 Sprinter Van
680-013634AA
OUT
7559
Dia. - 4"
Lgth. - 7"
In/Out - #8 Stat Seals (# 0131)
Freightliner Columbia, M2
A22-63992-000, A22-63992-001
7558
Accumulator
2003-2008 GMC G Series O.E.# 25760829
IN
7561
Dia. - 4"
Lgth. - 7"
In/Out - #8 Stat Seals (# 0131)
Freightliner
A22-63993-001, A22-65550-000
7560
Dia. - 2 1/2"
Lgth. - 7 3/4" (13.88" OAL)
MIO fittings with orifice tube
CAT OE#257-3227
IN
OUT
IN
#12 = 3/4”
RECEIVER DRIERS
7556
Pad Style Drier
2003-06 Sprinter Van, 2.7TD
051-03570AA
#10 = 5/8”
OUT
# 0011
o-ring
7562
Dia. - 2 5/8”
Lgth. - 7 1/2”
In - 3/8" #6 Male O-ring
Out - 3/8" #6 Female O-ring
16 cu. in. dessicant In-Line Drier
Pressure Relief Vavle
Kysor
402618
7565
Dia. - 4"
Lgth. - 6 3/4"
In/Out - 3/8" x 3/8" Male O'ring
Side Sight Glass
Volvo Off Road VRE
RD5-6075-0
© 2011 MEI Corporation
7563
Dia. - 2 1/2"
Lgth. - 8”
In - 3/8" Male O'ring
Out - Male Quick Disconnect
Fuse Plug; Motorhome
7566
Dia. - 4"
Lgth. - 7"
In/Out - #8 Stat Seals (#0131)
Freightliner Coronado
A22-63994-001
054-00011
7564
Dia. - 3”
Lgth. - 14.35”
#6 Spring Lock Connections
Ford New Holland OE# 89154-00
7567
Dia. - 3”
Lgth. - 10”
In - 3/8" Male O-ring
Out - 3/8" Male O-ring
Western Star 088586-00
459
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
#6 = 3/8”
#8 = 1/2”
#10 = 5/8”
#12 = 3/4”
female port
# 0025
RECEIVER DRIERS
o-rings
M10
Port
3/8”-24
Port
female port
# 0025
o-rings
7568
Pad Type Drier
Dia. - 2.4”
Lgth. - 10”
CAT# 176-1902
7569
Pad Type Drier
Dia. - 2.9”
Lgth. - 9”
LINKBELT EXCAVATOR
OE# YT54500003P1
7570
7570M ...... Metric threads
Dia. - 2.6”
Lgth. - 11 3/8”
3/8" x 3/8" Male Insert O'ring
(2) Female Ports
HINO TRUCK
7571
Dia. - 2-3/4”
Lgth. - 10”
Pad Type Drier
MITSUBISHI FUSO
7572
Dia. - 4”
Lgth. - 7 3/4”
In - #6 Female O'ring
Out - #6 Male Insert O'ring
CASE TRACTOR
OE# 86984155
7573
Dia. - 3”
Lgth. - 11 1/2”
In - #6 Female O'ring
Out - #6 Male Insert O'ring
J. DEERE OE# RE214440, 088545-00
7574
Dia. - 3”
Lgth. - 11 1/2”
In - #6 Female O'ring
Out - #6 Male Insert O'ring
J. DEERE OE# AL163559, 088549-00
7575
Dia. - 4”
Lgth. - 7”
In - #6 Female O'ring
Out - #6 Male Insert O'ring
J. DEERE OE# AL162467
7576
Accumulator
Dia. - 3 1/2”
J. DEERE, 670D Grader
OE# 803-465, AT190809
IN
OUT
IN
OUT
# 1418
switch
# 0187
pad o-ring
7577
Dia. - 3”
Lgth. - 10”
Top Sight Glass
FORD/NEW HOLLAND
OE# 803-380, 82012480
460
#12 o-rings
Springlock
7578
Accumulator w/Hose
Ford 2008-09
8C3Z-19C836C
7579
VOLVO Construction A25B
OE# 11005931
© 2011 MEI Corporation
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
7580
3/8" Male Insert O’ring
VOLVO Loader
oe# 20490945
7583
Accumulator
Ford E-Series 7C2Z-19C836B
IN
#8 = 1/2”
IN
#10 = 5/8”
#12 = 3/4”
OUT
7582
Dia. - 2 1/2"
Lgth. - 8"
3/8" Male Insert O’ring
16mm Port
Female 1/4” Switch Port
oe# 085737
7581
Dia. - 2 1/2"
Lgth. - 8"
3/8" Male Insert O’ring
Female 3/8”-24 Switch Port
oe# 085164
# 0131
# 0131
sealing
washers
sealing
washers
7585
Freightliner Cascadia
oe# 22-66700-000
7586
Freightliner M2
oe# A22-66600-000
UNIVERSAL DRIER and FITTING KIT - great for service trucks
Allows the use of Standard or Metric Charge Port Fittings
P/N
Has Multiple Charge Ports
for use with #8999 Fitting Kit
7600
Dia. - 2 1/2"
Lgth. - 8”
In - 3/8” Male O-ring
Out - 3/8” Female O-ring
Top Sight Glass
Moisture Indicator
(3) 3/8”-24 Female Switch Ports
© 2011 MEI Corporation
8999
Universal Drier Fitting Kit
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Qty. Description
0011 ... 10 .... 3/8” O-rings
4136 .... 1 ..... 3/8” MOR to 3/8” MIO drier adapter
4137 .... 1 ..... 11/16” MOR to 3/8” MIO drier adapter
4161 .... 1 ..... 3/8”-24 male to M10 sw. port adapter
4162 .... 1 ..... 3/8”-24 male to 12mm metric adapter
4165 .... 1 ..... 3/8”-24 to 13mm charge port adapter
4166 .... 1 ..... 3/8”-24 to 16mm charge port adapter
4167 .... 1 ..... 7/16” FF to M10 Male sw. port adapter
4168 .... 1 ..... M10 FF to 7/16” MF, R12 flare adapter
4913 .... 2 ..... 3/8" MOR to Flare adapter
4922 .... 2 ..... 3/8" MOR to 3/8" FF adapter
5527A .. 1 ..... 3/8" MOR, 3/8" FOR, R12 Inline Chg Ftg.
5685 .... 1 ..... 3/8”-24, Pressure Relief Valve
8900 .... 2 ..... 3/8”-24 male thrd. to 7/16” MF, R12 adpt.
8915 .... 5 ..... Std. Valve Cores R12/R134a
461
RECEIVER DRIERS
OUT
#6 = 3/8”