Table of Contents RECEIVER DRIERS
Basic Information
Receiver Driers, Accumulators, and In-Line Filters are canisters used to filter debris and
remove moisture to protect the a/c system. Various inlet and outlet fitting types and sizes are
used. Many also have system protection devices, moisture indicators, charge ports, sight glass,
fuse plugs, high pressure relief valves, mounting brackets depending on the requirements from
the original equipment manufacturer.
Receiver Driers are usually located on the high side of the a/c system before the expansion
valve. The receiver drier “receives” liquid refrigerant from the condenser, stores it, filters out
contaminates from the a/c system, and removes moisture. A/C systems using a receiver drier
use an expansion valve to control the refrigerant flow.
Accumulators are similar to that of the receiver drier. It is usually mounted on the low side,
at the outlet of the evaporator. The accumulator “accumulates” or stores excess refrigerant,
filters and dries the refrigerant. Accumulators are used on CCOT (Cycling Clutch Orifice Tube)
or FFOT (Ford Fixed Orifice Tube) systems. These systems use a orifice tube instead of an
expansion valve to control the refrigerant flow.
Filter Drier manufacturers have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
RECEIVER DRIERS
RECEIVER DRIERS
NOTE
DRIER
MEASUREMENTS
ACCUMULATORS
Specification Chart................................................... 499
Visual Numerical Section......................................... 508
LENGTH
RECEIVER DRIERS
Specification Charts................................................. 499
Block, Manifold, Pad or Slimline Type...................... 499
Flare Type................................................................. 503
In-Line Filters........................................................... 503
O’ring Type............................................................... 499
Quick Disconnect Type............................................. 502
DIAMETER
RELATED ITEMS
Adapters, Drier Port................................................. 395
Moisture Indicators.................................................. 507
Mounting Bracket Kits.............................................. 507
O’rings & Seals........................................................ 487
Quick Disconnect Couplers...................................... 507
Typical Drier System (illustration)............................ 504
Typical Accumulator CCOT (illustration).................. 506
© 2015 MEI Corporation
497
RECEIVER DRIERS
Moisture can be harmful to air conditioning systems, components and to the a/c system’s operation. For this reason, any time the a/c system is
opened, the receiver drier / accumulator needs to be replaced. A good preventative maintenance practice is to replace the receiver drier or the
accumulator and orifice tube at regular intervals or at least once per year. When replacing a compressor, the a/c compressor manufacturer’s
warranty will be void without proof of flushing the system, and also replacement of the receiver drier.
Moisture Indicator - a litmus paper device which turns colors to designate condition of the refrigerant.
Blue - Normal, Pink - Moisture in system, White - Very Wet, Grayish - oil contamination.
Manufactures have discontinued using moisture indicators. We will supply until stock is exhausted.
Pressure Relief Valve / Fuse Plug - A protection device designed to open and “bleed off” excessive pressure that may occur.
The Fuse Plug is a bi-metal device which will “melt down” to release excess pressure.
Sightglass - a “window” for observing the condition of the refrigerant.
Schrader Valve - a gauge or charge port which allows access to the system, for charging or checking the pressures.
Switch Port - Low / High Pressure Switches - a switch port allows for a male or female pressure switch to be added to the drier. If low charge
is detected, the low pressure switch opens electronically and stops the compressor operation. Similarily, as pressure increases, the high
pressure switch will dis-engage the clutch and re-engage when pressure normalizes.
Typical Examples:
Moisture indicator is not required and may not be supplied on drier.
Quick
Disconnect
RECEIVER DRIERS
Low / High
Pressure Switch
Sight
Glass
Female
O’ring Type
Charge/ Gauge
Port
Moisture
Indicator
(not required)
Sight
Glass
High Pressure
Relief Valve
Slimline Manifold - Block Type
Charge/Gauge
Port
High Pressure
Relief Valve
Moisture
Indicator
Charge/ Gauge
(not required) Port
Sight
Glass
Quick
Disconnect
Male Flare Type
(R12 only)
Male O’ring
Type
Pad Type
Fuse
Plug
Male
O’ring Type
High Pressure
Relief Valve
Female
Springlock Type
Female O’ring
Type
Sight Glass
(some models)
Male
Springlock Type
Switch Port
(some models)
498
TECH
TIP
Metric Schrader Valve uses green o’ring seals.
© 2015 MEI Corporation
RECEIVER DRIERS
Listed in ascending order by Diameter x Length by Fitting Type and Size.
11-5/8”
9”
10”
7”
9”
10”
10”
9-1/2”
9”
10”
10 1/4”
10 1/2”
11”
11”
11”
11”
11”
14.35”
7”
7”
7”
-
-
-
Pad Type
Pad Type
Pad Type
Pad Type
Pad Type
PadType
Pad Type
Pad
Pad Type
Slimline #6
Slimline #6
Pad /Block
Manifold
Pad Manifold
Pad Manifold
Pad Manifold
Pad Type
Springlock
Block Style
Block Style
Pad Type
Pad Type
-
-
Pressure
Relief Valve
Moisture
Indicator
Schrader
Valve
Outlet
Size
Note
O’ring 0011
-
O’ring 0025
O’ring 0011
-
O’ring 0011
-
-
O’ring 0025
seals 0126
seals 0126
O’ring 0135
O’ring 0011
-
-
-
-
SL 3/8” #6 Stat Seal #8
Stat Seal #8
Stat Seal #8
O’ring 0110
Stat Seal 0131
Stat Seal 0131
O’ring 0011
-
O’ring 0025
O’ring 0011
-
O’ring 0011
-
-
O’ring 0025
seals 0126
seals 0126
O’ring 0135
O’ring 0011
-
-
-
-
SL 3/8” #6
Stat Seal #8
Stat Seal #8
Stat Seal #8
O’ring 0110
Stat Seal 0131
Stat Seal 0131
7557
7420
Top
(2) Fem
7568
7547
7599
Top
7546
7571
7615
7569
M10
7197
(2) M10
Top
7198
(2) M10 Top
7545
16mm
7393
7397
7398
7399
7411
7564
Side
7559
7566
7561
7556
7585
7586
Charge
Sprinter Van 680-013634AA
R134a
JD Excavator, 4448179;4646799
R134a
CAT 176-1902
Caterpillar 113-3497
w/Trinary Sw., GMC/ISUZU 8-98039-052-0
CAT 176-1902; Komatsu 20Y-979-320
Mitsubishi Fuso
Kubota T2055-72230
3/8”-24 port; Linkbelt Exv YT54500003P1
N83-319744
R134a
use #0126 seals, N83-319534
R134a
Volvo Off-Road 11104567
R134a
Kenworth F37-6000 R134a
Peterbilt F37-6002
R134a
Peterbilt F37-6003
R134a
Peterbilt F37-6009
R134a
Peterbilt F37-1019
R134a
Ford New Holland
R134a
Frghtlnr A22-63992-000, -001
R134a
Frghtlnr A22-63994-001
R134a
A22-63993-001, A22-65550-000
R134a
Sprinter Van 2.7L, 051-03570AA
R134a
Frghtlnr 22-66700-000
R134a
Frghtlnr 22-66600-000
R134a
© 2015 MEI Corporation
Low Pressure
Switch
Pressure
Relief Valve
Moisture
Indicator
Schrader
Valve
OUTLET
3/8” #6
Course Thrd
Fine Thread
M18
Fine Thread
M18 MOR 1/2”#8
MOR M20
3/8” #6
3/8” #6
FOR 3/8” #6
MIO, M18
3/8” #6
3/8” #6
MIO
Fuse Plug
INLET
3/8” #6
3/8” #6
M18
M18
M18
M18 3/8” #6
M18
3/8” #6
3/8” #6
3/8” Male
MIO, M18
3/8” #6
3/8” #6
3/8” #6
Switch
Port
LENGTH
5.9”
6 5/16”
6 5/16”
6 5/16”
6 5/16”
6.32”
6 3/4”
6 3/4”
8”
8”
8”
8”
8 1/4”
10”
-
Sight Glass
Dia.
2 1/2”
2 1/2”
2 1/2”
2 1/2”
2 1/2”
2 1/2”
2 1/2”
2 1/2”
2 1/2”
2 1/2”
2 1/2”
2 1/2”
2 1/2”
2 1/2”
-
PART
NUMBER
2 1/2” Diameter - 3/8” or M18 Male O’ring INLET w/Various Outlets
7532 Top 3/8”
Side
7513 Top (1) M10
7514 Top (1) M10
7515 Top (1) M10
7519 Top (1) M10
7524 Top (1) M10
7140
7503
7118 Top (2) Top
7120 Top 1/4”Male
Top
7600 Top
(3)
Top
7614 Top
7480
Top
7502
7580
Note
3/8 O’ring port; 085428-00
33-0038A; 085623-00
33-0382A; 088370-0
33-0383A; 088371-00
Motorhome 085686-00
RV218337, 085722
In-Line Design, GMC
In-Line Drier; 15982368
085268-03 (new style)
use #1430 switch
Univ. Allows Std or Metric Ftgs
Doosan Excav., 2204-6039A
Bracket
RD remote condenser
Volvo 20490945
Charge
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R134a
R12/R134a
R12/R134a
R134a
499
RECEIVER DRIERS
1 5/8”
2 3/8”
2 .4”
2 1/2”
2 1/2”
2 1/2”
2 3/4”
2.38”
2.9”
3”
3”
3”
3”
3”
3”
3”
3”
3”
4”
4”
4”
-
-
-
Inlet
Size Switch
Port
Dia. LENGTH TYPE
PART
NUMBER
Block, Pad, Manifold, SlimLine, or SpringLock Style Fittings
RECEIVER DRIERS
Listed in ascending order by Diameter x Length by Fitting Type and Size (continued).
8 1/2”
8”
10”
10”
10”
10”
10”
10”
10”
10”
10”
11 3/8”
11 3/8”
#6 MIO
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” MIO
14mm
Low Pressure
Switch
Pressure
Relief Valve
Moisture
Indicator
Schrader
Valve
7119 Top (2) R12
Multi fit applications
7122
Top Side
Side
Thermo King Tri-Pac #61-3552
7154 Top
Side
7155 Top
1/4” Side
Side
Mack 221RD328
7155B Top Side
Side
Mack 221RD327 w/binary
7156 Top Side
Side
7157 Top
w/ Trinary Switch - #1550
7388 Side Top
Side
Kenworth K251-263
7389 Side
Top
Side
IHC1691600C92
7390 Side Top
Side
w/ Trinary Switch - Top
call
Top Top
Top 1/4” Side
Side
Mack 221RD327, w/Binary 7570
Hino Truck 7570M
Side
(2) female ports; Hino Truck Fuse Plug
#6 MIO
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” MIO
14mm
Switch
Port
OUTLET
Note
Charge
R12/R134a
R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
3”
6 1/2”
3/8” #6
NOTE
3/8” #6
7594
Low Pressure
Switch
Pressure
Relief Valve
Moisture
Indicator
Schrader Valve
Fuse Plug
Switch
Port
OUTLET
Sight Glass
DIA. LENGTH INLET
PART
NUMBER
3” Diameter — 3/8” Male O’Ring INLET x 1/2” Male O’Ring OUTLET
Male
Note
Charge
CAT Exv., M318 / FNH EC270R12/R134a
Filter Drier manufacturers have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
500
Low Pressure
Switch
Pressure
Relief Valve
Moisture
Indicator
OUTLET
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
Schrader
Valve
INLET
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
Fuse Plug
LENGTH
8”
8”
8 1/4”
10”
10”
7 3/4”
Switch
Port
Dia.
3”
3”
3”
3”
3”
4”
Sight Glass
3/8” Male O’Ring INLET x 3/8” Female O’Ring OUTLET
PART
NUMBER
RECEIVER DRIERS
2”
2 1/2”
2 3/4”
2 3/4”
2 3/4”
2 3/4”
2 3/4”
2 3/4”
2 3/4”
2 3/4”
2 3/4”
2.6”
2.6”
LENGTH INLET
PART
NUMBER
Dia.
Sight Glass
2” thru 2 3/4” Diameter - 3/8” Male O’ring INLET x 3/8” Male O’ring OUTLET
Note
7135 Top
(2) 1/4”
Side
7170 Top
(2) M10 Top
Side
(M10 x 1.25mm)
7172 Top
(2) 1/4”
Top
Top
Peterbilt 18-03638
7160 Top
(2) 1/4”
Side
similar to #7135
7169 Top
(2) M10 Top
7395
Charge
R12/R134a
R12/R134a
R12
R12/R134a
R12/R134a
R12/R134a
© 2015 MEI Corporation
RECEIVER DRIERS
Listed in ascending order by Diameter x Length by Fitting Type and Size (continued).
7125
7124
7593
7129
7123
7126
7127
7128
7555
7161
Top Side
Side
Side
Side
Top Female
Side
Terex Loader SKL863, SKL873
Top
Side
Top Side
Top Side
Red Dot RD5-7272-0
Top
1/4” Side
Side
088423-00; 01
Top
Side
Binary (Side)
Top
Side
Trinary (Side)
Top
Top Side
N83-319634; RD5-9419-0
(2) 1/4”
R12/R134a
R12/R134a
R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
3”
3”
3”
3”
3”
3”
3”
3”
3”
3”
3”
3”
3”
3”
3”
3”
3”
3”
3”
3”
3”
4”
4”
4”
4”
4”
-
8 1/4”
8 1/4”
8 1/4”
8 1/2”
8”
9”
9”
9”
9”
9”
9 3/4”
10”
10”
10”
10”
10”
10”
10”
10”
10”
10 1/2”
6 1/2”
6 3/4”
7”
7 3/4”
8 1/2”
-
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
#6 MIO
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
-
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
#6 MIO
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
-
7133 Top Female
Side
7141 Side Top
7143 Top
Side 1/4” Side Top
7229 Top Female
Top
7180
Top (2)
(2) M10 x 1.25mm
7159 Top
1/4” Top Top Side
7164 Top Side
Top Side
1/8”-27NPT Port; 088254-01
7174
Top Side
20407203
7185
Top Top
Inlet - Right Angle
7419
Top
Mack 221RD44M
7346 Top
w/side mounting bracket
7193 Top
Side 1/4” Side Top
Western Star
7132 Side
Side Top
Top
7134 Top Top
Top Side
Kenworth K251-566
7165 Top
1/4” Top Top Top
7166 Top
M10 Top Top Top
M10 x 1.25mm
7175 Side 1/4” fem
Side
088079-00; 176237; K251-459
7189 Top
w/side mounting bracket
7190 Top
Top
w/side mounting bracket
7567
Western Star 088586-00
7612 Side (3)1/4”
Volvo 1089855
7394 Top
w/mounting bracket
7565 Side
Side
Volvo RD5-6075-0
7232 Top
Side
Top
Opposite Side Inlet
7391 Top
Top Side Side
7234 Top
Side
Top
Top CAT# 5V5698; 8P9991
7613
J.Deere 582166227
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R134a
R12/R134a
R134a
R12/R134a
R134a
R12/R134a
R134a
© 2015 MEI Corporation
Note
Charge
501
RECEIVER DRIERS
Low Pressure
Switch
Pressure
Relief Valve
3/8” #6
#6 Flare
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
Moisture
Indicator
3/8” #6
#6 Flare
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
Schrader
Valve
6”
6 1/4”
6 1/4”
6”
6 1/2”
6 1/2”
6 1/2”
6 1/2”
6 1/2”
8”
LENGTH INLET
Fuse Plug
3”
3”
3”
3”
3”
3”
3”
3”
3”
3”
Dia.
Switch
Port
OUTLET
PART
NUMBER
Sight Glass
3” thru 4” Diameter - 3/8” Male O’ring INLET x 3/8” Male O’ring OUTLET
RECEIVER DRIERS
Listed in ascending order by Diameter x Length by Fitting Type and Size (continued).
8 3/4”
3/8” #6
Low Pressure
Switch
Pressure
Relief Valve
Moisture
Indicator
Schrader
Valve
Fuse Plug
Switch
Port
OUTLET
3/8” #6
-
#6 MIO
#6 MIO
#6 MIO
3/8” #6
3/8” #6
3/8” #6
#6 MIO
3/8” #6
Note
7387 Side
Top
K251-459,K251-571
7577 Top
Ford New Holland, 82012480
7573
JDeere, RE214440
7574
JDeere, AL163559 w/bracket
7575
JDeere, AL162467 w/bracket
7223 Top
7233 (2) Side
R12/R134a
7243 (2) Side
John Deere RE49169
7572
CASE, 86984155
7597
JDeere w/oe# AZ45582
3/8” #6
Side/Top
7392
Top
JDeere AT162848; AT151981
Charge
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
3”
3”
3”
4”
10”
10”
10”
9”
7/16” #6
11/16” #6
11/16” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
3/8” #6
Low Pressure
Switch
Pressure
Relief Valve
Moisture
Indicator
Schrader
Valve
Fuse Plug
OUTLET
Switch
Port
LENGTH INLET
Sight Glass
Dia.
PART
NUMBER
3/8” Female O’ring INLET x 3/8” Female O’ring OUTLET
7131 Top
Top
Top
Side
7130 Top
Top
Top
7230 Top
16mm
Top
7396
Note
Charge
3/16” Charge Port
alternate #7131
ParkerType; IHC 1693117C1
Ford Tractor E2NN-19825AA
R12/R134a
R12/R134a
R134a
R12
2 1/2”
2 1/2”
2 1/2”
2 1/2”
2 1/2”
2 1/2”
2 1/2”
3”
3”
3”
3”
3”
4”
502
6”
6”
6 5/16”
6 5/16”
6 5/16”
6 5/16”
7 3/4”
9 5/8”
10”
10”
10”
10”
8 1/2”
QD
QD
3/8” #6
M18
M18
M18
QD
QD side
QD
QD
QD
QD
QD
Low Pressure
Switch
Pressure
Relief Valve
7173
In-Line; Peterbilt 18-03841
7176 Top
(1) M10
(1) M10 x 1.25mm - Top
7513 Top
(1) M10
(1) Top M10 Male; 085623-00
7514 Top
(1) M10
(1) M10; 33-0382A; 088370-0
7515 Top
(1) M10
(1) M10; 33-0383A; 088371-00
7519 Top
(1) M10
Motorhome 085686-00
7145
Side
Incl. orifice tube; CAT3E3535
7199 Top
(2) M10
ABP N83 319524; 088470-01
7163 Top
(2) 1/4” Top Top
2 Schrader Vlvs (1/4” Top)
7168 Top
(2) M10
(2) M10 x 1.25mm (Top)
7179 Top
16mm
Top Side
R134a Service Port
7386 Side
Top
7236 Top
Top Side
Side
Moisture
Indicator
QD
QD
Course Thrd
Fine Thread
M18
Fine Thread
QD
QD 60mm
QD
QD
QD
QD
QD
Schrader
Valve
OUTLET
Fuse Plug
LENGTH INLET
Switch
Port
Dia.
Sight Glass
Quick Disconnect Type
PART
NUMBER
RECEIVER DRIERS
4”
LENGTH INLET
10”
3/8” #6
10”
-
11 1/2” 3/8” #6
11 1/2” 3/8” #6
7”
3/8” #6
7”
3/8” #6
7 1/2”
3/8” #6
7 1/2”
3/8” -18
7 3/4”
3/8” #6
8 1/2”
3/8” #6
Sight Glass
Dia.
3”
3”
3”
3”
4”
4”
4”
4”
4”
4”
PART
NUMBER
3/8” Female O’ring INLET x 3/8” Male O’ring OUTLET
Note
Charge
R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R134a
R134a
R134a
R134a
R134a
R134a
R134a
© 2015 MEI Corporation
RECEIVER DRIERS
Listed in ascending order by Diameter x Length by Fitting Type and Size (continued).
Note
Charge
2 1/2”
2 1/2”
2 1/2”
2 1/2”
2 1/2”
2 1/2”
2 1/2”
2 1/2”
2 1/2”
2 5/8”
2 3/4”
6”
6 3/4”
6 3/4”
6 3/4”
7”
7”
7 3/4”
7 3/4”
10”
7 1/2”
8 1/2”
QD
3/8” #6 Male Flare
3/8” #6 Male O’Ring
M18 Male O’Ring
1/2” Flare
1/2” Flare
QD
MIO Fitting
3/8” Male O’Ring
3/8” #6 Male
1/2” Flare
QD
3/8” #6 Male Flare
1/2” #8 Male O’Ring
M20 Male O’Ring
1/2” Flare
1/2” Flare
QD
MIO Fitting
3/8” Male O’Ring
3/8” #6 Female
1/2” Flare
7173
7501
7140
7503
7500
7504
7145
7560
7502
7562
Side
7542 Side
In-Line Drier; Peterbilt 18-03841
In-Line Drier WAH 163; 16cu.in.
In-Line Design,GMC
In-Line Drier; GMC 15982368
In-Line Drier; WLD164FO; 16cu.in.
In-Line Drier; WAH164; 16cu.in.
Enclosed Orifice; CAT# 3E3535
w/Orifice Tube, CAT# 257-3227
In-Line Drier, RD remote cond.
16 cu.in. dessicant; Kysor 402618
In-Line Drier WSG164FO; 16cu.in
R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R134a
R134a
R12/R134a
R12/R134a
R12/R134a
2 3/4”
3”
3”
3”
3”
3”
3 3/4”
4”
8 1/2”
10”
10”
10 1/2”
10 1/2”
11 1/2”
10 3/4”
7 1/2”
1/2” #8 MIO
1/2” Flare
1/2” SAE
3/8” #6 Male
5/8” SAE
1/2” #8 MIO
1/2” Flare
3/8” Female O’Ring
1/2” #8 MIO
1/2” Flare
1/2” SAE
3/8” #6 Female
5/8” SAE
1/2” #8 MIO
1/2” Flare
3/8”-18 Male O’Ring
7541 Side
7540
7548 Side
7596 Side
7551
7549 Side
7517
7243 (2) Side
In-Line Retro; Carrier A/C; 16cu.in.
In-Line, EK304; 212-010; 30cu.in.
In-Line, Carrier WSG304; 30cu.in
FNH Backhoe 555E-685E; 85804063
In-Line, Carrier WAH305; 30cu.in.
In-Line, Carrier ADK304; 30cu.in.
In-Line, TransAir AH414; 41cu.in.
In-Line Drier JDeere RE49169
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
NOTE
Filter Drier manufacturers have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
2 1/2”
2 1/2”
2 1/2”
2 1/2”
3”
3”
4”
4”
6 3/4”
7”
8”
8”
6 1/4”
10”
7 3/4”
7”
© 2015 MEI Corporation
#6 Flare
1/2” Flare
#6 Flare
#6 Flare
#6 Flare
1/2” Flare
#6 Flare
#6 Flare
Low Pressure
Switch
Pressure
Relief Valve
Moisture
Indicator
7501
In-Line; 16cu.in.; WAH163
7500
In-Line ; WLD164FO; 16cu.in.
7152 Top
7218 Top
Top
Top w/Low Pressure Sw.
7124 Top
Side
w/Fuse Plug
7540
In-Line; 30cu.in.; EK304
7235 Top
Side
w/Fuse Plug
7211 Top
Side
w/Fuse Plug
Schrader
Valve
#6 Flare
1/2” Flare
#6 Flare
#6 Flare
#6 Flare
1/2” Flare
#6 Flare
#6 Flare
Fuse Plug
OUTLET
Switch
Port
LENGTH INLET
PART
NUMBER
Dia.
Sight Glass
Flare End Fittings - Male INLET and Male OUTLET
Note
Charge
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12/R134a
R12
R12/R134a
503
RECEIVER DRIERS
OUTLET
Moisture
Indicator
LENGTH INLET
Sight Glass
Dia.
PART
NUMBER
In-Line Filters / Driers
RECEIVER DRIERS
Typical Drier System
RECEIVER DRIERS
Compressor
Expansion Valve
Drier
Condenser
504
Suction
Evaporator
Thermostat
© 2015 MEI Corporation
RECEIVER DRIERS / ACCUMULATORS
Listed in ascending order by Diameter x Length by Fitting Type and Size.
Length
2 3/8”
7 1/2”
3”
8”
3 7/16”
9 1/2”
3 1/2”
8”
3 1/2”
8”
3 1/2”
8”
3 1/2”
8 1/8”
3 1/2”
8 3/4”
3 1/2”
8 7/8”
3 1/2”
8 7/8”
3 1/2”
9”
3 1/2”
9”
3 1/2”
9”
3 1/2”
9”
3 1/2”
9”
3 1/2”
9”
3 1/2”
9”
3 1/2”
8”
3 1/2”
9”
3 1/2”
9”
3 1/2”
9”
3 1/2”
9”
3 1/2”
9”
3 1/2”
9”
3 1/2”
9”
3 1/2”
9”
3 1/2”
9”
3 1/2”
9 1/8”
3 1/2”
9 1/8”
3 1/2”
9 1/8”
3 1/2”
9 3/4”
3 1/2”
9 3/4”
3 1/2”
9 13/16”
3 1/2”
10”
3 1/2”
10”
3 1/2”
10”
3 1/2”
12.3”
3 1/2”
-
3 1/2”
-
3 1/2”
-
3 1/2”
-
3 1/2”
-
3 1/2”
-
3 1/2”
-
3 1/2”
-
3 1/2”
-
3 1/2”
3 1/2”
-
© 2015 MEI Corporation
Inlet
Type
Inlet
Size
Outlet
Type
Outlet
Size
Pad Type
-
-
MIO
5/8” #10
MIO
3/4” #12
Pad
-
Pad -
FOR
M27
MIO
M27
FOR
3/4” #12
FOR
3/4” #12
Male Pad
Female Pad
MIO
5/8” #10
MIO
3/4” #12
Male SL
5/8” #10
Male SL
3/4” #12
Pad Type
0187
-
-
Pad Type
0187
FIOR
3/4” #12
FIOR
1/2” #8
FIOR
3/4” #12
FIOR
3/4” #12
MIO
3/4” #12
FOR
3/4” #12
MIO
3/4” #12
FOR
3/4” #12
MIO
3/4” #12
FOR
3/4” #12
MOR
3/4” #12
FOR
3/4” #12
MIO
3/4” #12
FOR
M27
MIO
M27
FOR
3/4” #12
MOR
3/4” #12
FOR
M27
MOR
M27
FOR
M27
MOR
M27
FOR
3/4” #12
MIO
3/4” #12
FOR
3/4” #12
MIO
3/4” #12
FOR
M27
MIO
M27
FOR
M27
MIO
M27
Pad Type
Pad
MIO
M27
Male SL
3/4” #12
Female SL
#10 & #12
Male SL
3/4” #12
Female SL
3/4” #12
FOR
1 1/16” FOR
1 1/16” FOR
1 1/16” FOR
1 1/16” Pad Type
-
-
Pad Type
MIO
3/4” #12
Female SL
3/4” #12
FOR #12 (1/16”-16)
FOR #12 (1/16”-16)
FOR
1 1/16” FOR
1 1/16” MOR
3/4” #12
MOR
3/4” #12
Female SL
3/8” #6
Female SL
5/8” #10
MIO
5/8” #10
MIO
3/4” #12
MOR
7/8” MOR
7/8” -
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Pad Type
#0187
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Pad Type
#0187
Springlock
#12
7592
7483
7415
7444
7406
7584
7493F, G
7482
7496A
7496
7486
7428
7427
7431
7450
7459
7430
7434
7446
7440
7448
7466
7466M
7469
7457
7383
7485
7409
7543
7408
7479
7595
7544
7369
7162
7454
7385
7416
7417
7488
7487
7490
7494
7489
7495
7552
7554
7578
Note
FIOR
FOR
MIO
MOR
SL
= Female Insert O’ring
= Female O’ring
= Male Insert O’ring
= Male O’ring
=Springlock
Volvo Exv EC Series, 14509377, R34a
M12 Port, 13mm Charge Port, F4TZ-19C836A, F6TZ-19C836AA
M12 Port; Navistar 3542577C2; BOA80-323-00-139
(1) M12 Port, GM 1132722, 2724924
Universal Type Accumulator; GM 12322992
(1) R143a Charge Port, (1) M12 Switch Port ; 1411812
F6HZ-19C936A; 4C4H-19C808AA
(1) M10 Switch Port, (1) Chg Port 13mm; F4UZ-19C836A
Ford F250/350, 6C3Z-19C836A
F81Z-19C 836AA
Ford F9UZ-19C1836AB; F65Z-19C836AA
(1) 1/4” Male Switch Port, (1) Male Charging Port
(2) 1/4” Ports, 2724802; 3090492
(2) 1/4” Ports; 1131506, 3059317, 27248336
(2) Serv Ports; 1131404, 2724266, 2724199, 2724804
(2) 1/4” Ports; GM 1131475, 2724877, 3057034, 3058262
w/M12 Port, 13mm R134a Port; 2724885, 2724665
(1) 1/4” Port,w/R134a Port, R12 Port; 1131843; 2724689
(1) M12 Port, GM 2724817
(1) M12 Port (1) M13 Port, GM 2724847
(2) 1/4” Port, GM 2724194
w/M12 Port 1 3/4” below Fittings, GM 2724475
w/M12 Port 1 3/4” below Fittings, GM 2724899
(1) M12 Port (1) 13mm Port, GM 2724886
(1) M12 Port (1) 13mm Port, GM 15005371
(2) 1/4” Ports, E69Z-19C836B
(1) M12 Port (1) M13 Port, Ford E49Z-19C836C
Peterbilt 18-03837
Caterpillar 1018789 (steel)
Peterbilt 18-04171; 700075
(2) 1/4” Ports; Ford E6VY-19C836A
CAT 186-6189
Caterpillar 089320-00, 197-6218
(2) R12 Ports, Ford E1VY-19C836A
Two (2) Schrader Valves: Top/Side
(2) 1/4” Ports, Ford E3TZ-19C836B, E7TZ-19C836A
M12 switch port, R134a Charge Port, F4HZ-19C836A
08 Navistar Prostar 3666273-C1, 3670134-C1
Navistar Prostar 3670134-C1. P6546001
Ford F7UZ-19C836BB
Ford E75Z-19C836AA
Ford XL3Z-19C836AA
Ford XL3Z-19C836BA
Ford F75Z-19C836BA
Ford E-Series, 2C2Z-19C836BA
w/ diesel eng., Ford E-Series, 7C2Z-19C836AA
Topkick/Kodiak 1132813 (#0142 Stat Seal)
08 Ford 8C3Z-19C836C (switch #1418)
505
RECEIVER DRIERS
Dia.
PART
NUMBER
Accumulators
ACCUMULATORS / RECEIVER DRIERS
Listed in ascending order by Diameter x Length by Fitting Type and Size (continued).
Dia.
Length
-
-
-
Stat Seal
Pad Pad -
-
-
Inlet
Size
-
-
-
#12
-
-
-
-
-
Outlet
Type
-
-
-
Stat Seal
FIOR
Stat Seal
-
-
-
Outlet
Size
-
-
-
#12
3/4” #12
#12
-
-
-
call
call
7576
call
7498
7558
7583
7588
7400
Note
FIOR
FOR
MIO
MOR
SL
= Female Insert O’ring
= Female O’ring
= Male Insert O’ring
= Male O’ring
=Springlock
GMC 04-06 Silverado 1411646
GMC 01-05 Silverado Avalanche 1411647
J. Deere 670D Grader AT190809, 803-465
GMC 01-05 Silverado Avalanche 1411648
(2) 13mm Ports, M10 Switch Port; F85Z-19C 836AB
GMC G Series 2003-08, 25760829
Ford E-Ser. 7C2Z-19C836B
13mm Charge Port, Ford Transit-conn. 9T1Z-19C836A: YF3625
Carrier 65-00193-00; 088599-01
RECEIVER DRIERS
3 1/2”
-
3 1/2”
-
3 1/2”
3 1/2”
-
4”
10 1/4”
-
-
-
-
13 1/4”
7 1/2”
-
-
Inlet
Type
PART
NUMBER
Accumulators (continued)
Typical Accumulator System
CCOT - Clutch Cycling Orifice Tube
Compressor
Accumulator
Orifice Tube
Evaporator
Thermostat
Condenser
506
© 2015 MEI Corporation
RECEIVER DRIERS
Quick Disconnect Couplers
3/8” female
thread
4138
Quick Disconnect Coupler
For IHC Applications
3/8” Female x Q.D. (1 per box)
4139
Quick Disconnect Coupler
For All Quick Disconnect Type Driers
3/8” Male Insert x Q.D.
2 1/4” length (1 per box)
3/8” male
thread
4971K
Quick Disconnect Coupler Assembly
Includes Valve Kit
1/2”-20 thread
Fits Drier #7513
1/2”-20
thread
RECEIVER DRIERS
Moisture Indicator
4160
1/2” Male Flare
1/2” Female Flare SAE
Drier Brackets
7471
Universal Drier Bracket
For driers 2 1/4” to 3” in diameter
© 2015 MEI Corporation
7472
Heavy Duty Drier Bracket
For driers 3” in diameter
7473
Heavy Duty Compact Bracket
For driers up to 4” in diameter
507
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
#6 = 3/8”
OUT
IN
OUT
#1430
switch
OUT
7118
Dia. - 2 1/2”
Lgth. - 8”
3/8” x 3/8” Male O’ring
Top Sight Glass
Female Switch Port
1/4” Male Switch Port
Freightliner A22-14425-2; 085268-03
#8 = 1/2” #10 = 5/8” #12 = 3/4”
IN
IN
7119
Dia. - 2”
Lgth. - 8 1/2”
In/Out - #6 Male Insert O’rings
Top Sight Glass
R12 Ports (2)
Multi fit applications
7120
Dia. - 2 1/2”
Lgth. - 8”
In/Out - 3/8” x 3/8” Male O’ring
Top Sight Glass
Low Pressure Switch
1/4” Male Switch Port
IN
IN
RECEIVER DRIERS
IN
1/4” NPT
7122
Drier
Dia. - 2-1/2”
Lgth. - 8”
3/8” x 3/8” Male O’ring
Sight Glass
Fuse Plug
1/4” NPT Ftg
Thermo King Tri-Pac Unit #61-3552
IN
OUT
7125
Dia. - 3”
Lgth. - 6”
In/Out - 3/8” x 3/8” Male O’ring
Top Sight Glass, Side Switch Port
High Pressure Reliev Valve
IN
508
7124
Dia. - 3”
Lgth. - 6 1/4”
In/Out - 3/8” x 3/8” Male Flare
Top Sight Glass, Fuse Plug
OUT
OUT
7126
Dia. - 3”
Lgth. - 6 1/2”
In/Out - 3/8” x 3/8” Male O’ring
Top Sight Glass, Side 1/4” Schrader Valve
High Pressure Relief Valve
OUT
OUT
7128
Dia. - 3”
Lgth. - 6 1/2”
In/Out - 3/8” x 3/8” Male O’ring
Top Sight Glass
Side Trinary Switch, Fuse Plug
OUT
OUT
7123
Dia. - 3”
Lgth. - 6 1/2”
In/Out - 3/8” x 3/8” Male O’ring
Top Sight Glass, Side Switch Port
P.R.V. & Moisture Indicator
IN
IN
OUT
7129
Dia. - 3”
Lgth. - 6”
In/Out - 3/8” x 3/8” Male O’ring
Top Sight Glass, Fuse Plug
IN
7127
Dia. - 3”
Lgth. - 6 1/2”
In/Out - 3/8” x 3/8” Male O’ring
Top Sight Glass
Side Binary Switch, Fuse Plug
IN
OUT
7130
Dia. - 3”
Lgth. - 10”
In - 11/16” Female O’ring
Out - 3/8” Female O’ring
Top Sight Glass
Pressure Relief Valve
© 2015 MEI Corporation
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
IN
OUT
IN
#6 = 3/8”
OUT
7132
Dia. - 3”
Lgth. - 10”
In/Out - 3/8” x 3/8”
Male O’ring
Side Sight Glass
Top Schrader Valve
Moisture Indicator
Fuse Plug Relief Valve
7131
Dia. - 3”
Lgth. - 10”
In - 7/16” Female O’ring
Out - 3/8” Female O’ring
Top Sight Glass
Charge Port 3/16”
Moisture Indicator; PRV
#8 = 1/2” #10 = 5/8” #12 = 3/4”
IN
OUT
7133
Dia. - 3”
Lgth. - 8 1/4”
In/Out - 3/8” x 3/8”
Male O’ring
Top Sight Glass
Female Switch Port
Pressure Relief Valve
IN
IN
OUT
7134
Dia. - 3”
Lgth. - 10”
In/Out - 3/8” x 3/8” Male O’ring
Top Sight Glass
Top Switch Port
Moisture Indicator
Pressure Relief Valve
Kenworth K251-566
OUT
7135
Dia. - 3” Lgth. - 8”
In - 3/8” Male O’ring
Out - 3/8”Female O’ring
Top Sight Glass
(2) Schrader Valves
Pressure Relief Valve
7140
Dia. - 2 1/2”
Lgth. - 6 3/4”
In - 3/8” Male O’ring
Out - 1/2” Male O’ring
In-Line Design, GMC
RECEIVER DRIERS
IN
OUT
IN
IN
OUT
7141
Dia. - 3”
Lgth. - 8 1/4”
In/Out - 3/8” x 3/8” Male O’ring
Side Sight Glass, Top Switch Port
IN
OUT
7143
Dia. - 3”
Lgth. - 8 1/4”
In/Out - 3/8” x 3/8” Male O’ring
Top Sight Glass, Schrader Valve
Fuse Plug, Moisture Indicator
IN
OUT
7152
Dia. - 2 1/2”
Lgth. - 8”
In/Out - 3/8” x 3/8” Male Flare
Top Sight Glass
© 2015 MEI Corporation
7145
Dia. - 2 1/2”
Lgth. - 7 3/4” (13.88” OAL)
Quick Disconnect
Enclosed Orifice Tube
R134a Only
CAT 3E3535
IN
OUT
OUT
7154
Dia. - 2 3/4”
Lgth. - 10”
In/Out - 3/8” x 3/8” Male O’ring
Top Sight Glass
Side Low Pressure Switch
509
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
IN
#6 = 3/8”
#8 = 1/2” #10 = 5/8” #12 = 3/4”
OUT
IN
7155
Dia. - 2 3/4”
Lgth. - 10”
In/Out - 3/8” x 3/8” Male O’ring
Top Sight Glass
Side 1/4” Schrader Valve
Pressure Relief Valve
Mack 221RD328
7155B
Dia. - 2 3/4”
Lgth. - 10”
3/8” x3/8” Male O’’Ring with
Male Switch Port, Fuse Plug,
Top Sight Glass
Supplied w/Binary Switch #1510
Mack 221RD327
OUT
7156
Dia. - 2 3/4”
Lgth. - 10”
In/Out - 3/8” x 3/8” Male O’ring
Top Sight Glass
Side Switch Port
Pressure Relief Valve
1550
OUT
RECEIVER DRIERS
IN
IN
OUT
IN
OUT
7159
Dia. - 3”
Lgth. - 9”
In/Out - 3/8” x 3/8”
Male O’ring
Top Sight Glass
Top Schrader Valve
Moisture Indicator
Pressure Relief Valve
7160
Dia. - 3”
Lgth. - 10”
In - 3/8” Male O’ring
Out - 3/8” Female O’ring
Top Sight Glass
(2) Schrader Valves
Pressure Relief Valve
ABPN83-319714
7161
Dia. - 3”
Lgth. - 8”
In/Out - 3/8” x 3/8” Male O’ring
(2) Schrader Valves
7162
Accumulator
Dia. - 3 1/2”
Lgth. - 10”
In - 3/8” Female Springlock
Out - 5/8” Female Springlock
(2) Schrader Vlv (Top/Side)
7163
Dia. - 3”
Lgth. - 10”
Quick Disconnect
Top Sight Glass
(2) 1/4” Schrader Valves
High Pressure Relief Valve
Moisture Indicator; R134a Only
IN
IN
7157
Dia. - 2 3/4”
Lgth. - 10”
In/Out - 3/8” x 3/8” Male O’ring
Top Sight Glass
Side Trinary Switch
IN
OUT
OUT
7164
Dia. - 3”
Lgth. - 9”
In/Out - 3/8” x 3/8” Male O’ring
Top Sight Glass
Side Switch Port (1/8”-27 NPT)
Moisture Indicator
Pressure Relief Valve
088254-01
510
OUT
7165
Dia. - 3”
Lgth. - 10”
In/Out - 3/8” x 3/8” Male O’ring
Top Sight Glass
Schrader Valve
Moisture Indicator
Pressure Relief Valve
OUT
IN
7166
Dia. - 3”
Lgth. - 10”
In/Out 3/8” x 3/8” Male O’ring
Top Sight Glass
Pressure Relief Valve
Moisture Indicator
Metric Schrader Valve - M10
© 2015 MEI Corporation
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
#6 = 3/8”
#8 = 1/2” #10 = 5/8” #12 = 3/4”
OUT
OUT
IN
7168
Dia. - 3”
Lgth. - 10”
Quick Disconnect
Top Sight Glass
(2) Schrader Valves - M10
R134a Only
IN
IN
OUT
7170
Dia. - 3”
Lgth. - 8”
In - 3/8” Male O’ring
Out - 3/8” Female O’ring
Top Sight Glass
Pressure Relief Valve
Moisture Indicator
(2) Schrader Valves - M10
7169
Dia. - 3”
Lgth. - 10”
In - 3/8” Male O’ring
Out - 3/8” Female O’ring
Top Sight Glass
(2) Schrader Valves - M10
OUT
OUT
IN
7172
Dia. - 3’”
Lgth. - 8 1/4”
In - 3/8” Male O’ring
Out - 3/8” Female O’ring
Top Sight Glass
High Pressure Relief Valve
Moisture Indicator
(2) Schrader Valves - R12 Only
7173
In-Line Drier - R134a Only
Dia. - 2 1/2”
Lgth. - 6” (9.6” overall)
Quick Disconnect
Peterbilt OE# 18-03841
IN
7174
Dia. - 3”
Lgth - 9”
In/Out 3/8” x 3/8” Male O’ring
Pressure Relief Valve
Moisture Indicator
OE# 20407203
OUT
IN
7175
Dia. - 3”
Lgth. - 10”
In/Out - 3/8” x 3/8” Male
Side Sight Glass
1/4” Female Port
High Pressure Relief Valve
Kenworth OE# K251-459
OUT
RECEIVER DRIERS
IN
OUT
OUT
7179
IN
Dia. - 3”
Lgth. - 10”
Quick Disconnect
Top Sight Glass
Moisture Indicator
Pressure Relief Valve
R134a Service Port, 16mm
IN
7176
Dia. - 2 1/2”
Lgth - 6”
Quick Disconnect
Top Sight Glass
(1) Schrader Valve - M10
OUT
IN
OUT
IN
7180
Dia. - 3”
Lgth. - 8”
In/Out - 3/8” x 3/8” Male O’ring
(2) Schrader Valves - M10 PH088340-01
© 2015 MEI Corporation
7185
Dia. - 3”
Lgth. - 9”
3/8” x 3/8” Male O’ring
Inlet - Right Angle
Moisture Indicator
Pressure Relief Valve
511
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
IN
OUT
IN
#6 = 3/8”
OUT
IN
OUT
7193
Dia. - 3”
Lgth. - 10”
In - 3/8” Male O’ring
Out - 3/8” Male O’ring
Top Sight Glass
Fuse Plug, (1) 1/4” Port
Moisture Indicator
Western Star
7190
Dia. - 3”
Lgth. - 10”
In/Out - 3/8” x 3/8”
Male O’ring
Top Sight Glass
Moisture Indicator
7189
Dia. - 3”
Lgth. - 10”
In/Out - 3/8” x 3/8”
Male O’ring
Top Sight Glass
#8 = 1/2” #10 = 5/8” #12 = 3/4”
OUT
IN
OUT
RECEIVER DRIERS
IN
# 0126
seals
# 0126
7198
seals
Dia. - 3”
Lgth. - 10 1/4”
In/Out - 3/8” x 3/8”
Slimline use #0126 seals
Moisture Indicator
(2) M10 Switch Ports
R134a Only
ABPN83-319534
7197
Dia. - 3”
Lgth. - 10”
In/Out - #6 Slimline
Slimline use #0126 seals
(2) M10 Switch Ports
Pressure Relief Plug
ABPN83-319744
OUT
IN
7199
Dia. - 3”
Lgth. - 9 5/8”
In - QD (side)
Out - QD (top)
(2) M10 Ports, Sight Glass
Quick Disconnect - 60mm (2-3/8”)
ABPN83-319524; 088470-01
OUT
OUT
IN
7211
Dia. - 4”
Lgth. - 7”
In/Out - 3/8” x 3/8”
Male Flare
Top Sight Glass
Fuse Plug
7218
Dia. - 2 1/2”
Lgth. - 8”
In/Out - 3/8” x 3/8” Male Flare
Top Sight Glass
Top Schrader Valve
Low Pressure Switch
OUT
IN
7223
Dia. - 4”
Lgth. - 7”
In - 3/8” Female O’ring
Out - 3/8” Male O’ring
Top Sight Glass
IN
OUT
7229
Dia. - 3”
Lgth. - 8 1/2”
In/Out 3/8” x 3/8” Male O’ring
Top Sight Glass
Male Schrader Port
Female Switch Port
512
IN
7230
Dia. - 3”
Lgth. - 10”
In - 11/16” Female O’ring
Out - 3/8” Female O’ring
Top Sight Glass
Pressure Relief Valve
16mm Service Port; R134a Only
7232
Dia. - 4”
Lgth. - 7”
In/Out - 3/8” x 3/8”
Male O’ring
(opposite side inlet)
Top Sight Glass
Side Fuse Plug
Moisture Indicator
© 2015 MEI Corporation
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
#6 = 3/8”
#8 = 1/2” #10 = 5/8” #12 = 3/4”
OUT
IN
7233
Dia. - 4”
Lgth. - 7 1/2”
In - 3/8” Female O’ring
Out - 3/8” Male O’ring
(2) Side Sight Glass
IN
OUT
7234
Dia. - 4”
Lgth. - 8 1/2”
In/Out - 3/8” x 3/8”
Male Insert O’ring
Combo: Sight Glass and
Moisture Indicator,
Low Pressure Switch Port
Sided Fuse Plug
CAT 5V5698, 8P9991
7235
Dia. - 4”
Lgth. - 7 3/4”
In/Out - 3/8” x 3/8”
Male Flare
Top Sight Glass
Fuse Plug, R12
OUT
IN
OUT
RECEIVER DRIERS
IN
OUT
7236
Dia. - 4”
Lgth. - 8 1/2”
Quick Disconnect
Top Sight Glass
Moisture Indicator
Low Pressure Switch
Pressure Relief Valve; R134a Only
7243
Dia. - 4 “
Lgth. - 7 1/2”
In - 3/8” Female O’ring
Out - 3/8” -18 Male O’ring
(2) Side Sight Glasses
John Deere RE49169
IN
7346
Dia. - 3”
Lgth. - 9 3/4”
In/Out - 3/8” x 3/8” Male O’ring
Sight Glass
OUT
IN
7369
Accumulator Ford
Dia. - 3 1/2”
Lgth. - 10”
In - 3/4” Male O’ring
Out - 3/4” Male O’ring
(2) R12 Ports
OE# E1VY-19C836A
7383
Accumulator Ford
Dia. - 3 1/2”
Lgth. - 9”
In - 3/4” Male Springlock
Out - 3/4” and 5/8” Female Springlock
(2) 1/4” Ports
OE# E69Z-19C836B
7385
Accumulator
Dia. - 3 1/2”
Lgth. - 12.3”
In/Out - 7/8” Male O’ring
M12 Switch Port
R134a Charge Port
OE# 089248-00; F4HZ-19C836A
IN
OUT
OUT
7386
Dia. - 3”
Lgth. - 10”
Quick Disconnect
Side Sight Glass
Moisture Indicator; R134a Only
© 2015 MEI Corporation
IN
7387
Dia. - 3”
Lgth. - 10”
In - 3/8” Female O’ring
Out - 3/8” Male O’ring
Moisture Indicator
Side Sight Glass
Kenworth K251-571
513
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
IN
OUT
7388
Dia. - 2 3/4”
Lgth. - 10”
In/Out - 3/8” x 3/8” Male O’ring
Side Sight Glass
Top Switch Port
Pressure Relief Valve
Kenworth K251-263
IN
OUT
RECEIVER DRIERS
#8 = 1/2” #10 = 5/8” #12 = 3/4”
IN
7389
Dia. - 2 3/4”
Lgth. - 10”
In/Out - 3/8” x 3/8” Male O’ring
Side Sight Glass
Top Schrader Valve
Pressure Relief Valve
IHC OE# 1691600C92
IN
7391
Dia. - 4”
Lgth. - 7 3/4”
In/Out - 3/8” x 3/8”
Male O’ring
Top Sight Glass
Moisture Indicator
Side Low Pressure Switch
Pressure Relief Valve; R134a Only
#6 = 3/8”
OUT
7390
Dia. - 2 3/4”
Lgth. - 10”
In/Out - 3/8” x 3/8” Male O’ring
Side Sight Glass
Top Trinary Switch
Pressure Relief Valve
OUT
# 0011
o’rings
7392
Dia. - 4”
Lgth. - 8 3/4”
In - 3/8” Female O’ring
Out - 3/8” Male O’ring
Top Sight Glass and
Side Sight Glass
Moisture Indicator
J Deere AT151981, AT162848
IN
7393
Dia. - 3”
Lgth. - 11”
Manifold Connection Type
R134a Only
Kenworth T2000, F37-6000
OUT
7394
Dia. - 4”
Lgth. - 6 1/2”
In/Out - 3/8” x 3/8” Male O’ring
Top Sight Glass
7395
Dia. - 4”
Lgth. - 7 3/4”
In - 3/8” Male O’ring
Out - 3/8” Female O’ring
7396
Dia. - 4”
Lgth. - 6”
Horizontal Type
In - 3/8” Female Piloted O’ring Fitting
Out - 3/8” Female Piloted O’ring Fitting
7397
Dia. - 3”
Lgth. - 11”
Pad Manifold Fittings
330, 340, 387 Series
Peterbilt F37-6002
7398
Dia. - 3”
Lgth. - 11”
Pad Manifold Fittings
365 thru 389 Series
Peterbilt F37-6003
7399
Dia. - 3”
Lgth. - 11”
Pad Manifold Fittings
Peterbilt F37-6009
514
© 2015 MEI Corporation
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
#6 = 3/8”
#8 = 1/2” #10 = 5/8” #12 = 3/4”
OUT
IN
IN
7408
Accumulator
Dia. - 3 1/2”
Lgth. - 9 1/8”
uses (2) #0017 O’rings
and #4589SR fitting
Peterbilt Pad 18-04171
OUT
# 0017
o’rings
# 0139
suction
flange gasket
# 0137
suction o’ring
M12
7409
Dia. - 3 1/2”
Lgth. - 9 1/8”
In - 1 1/16” Female O’ring
Out - 1 1/16” Female O’ring
Peterbilt 18-03837
7415
Dia. - 3 7/16”
Lgth. - 9 1/2”
Pad Mount Accumulator
(1) M12 Port
Navistar 3542577C2;
BOA80-323-00-139
7411
Dia. - 3”
Lgth. - 11”
PAD type
Peterbilt F37-1019
1000538099BSM
# 0136
discharge o’ring
# 0136
discharge o’ring
# 0138
discharge
flange gasket
# 0138
discharge
flange gasket
# 0011
#6 o’ring
IN
uses:
#0156
o’ring/gasket kit
#1400 sensor
OUT
# 0011
#6 o’ring
uses:
7416
Drier Assy.
2008 Navistar Prostar
3666273-C1
7420
Pad Mount Drier
Dia. - 2-3/8”
Lgth. - 9”
(2) 3/8” x 24 Female Sw Ports
J Deere Excavators
OE# 4448179; 464699
© 2015 MEI Corporation
uses:
#0155
o’ring/gasket kit
7417
Drier Assy.
Navistar Prostar
3670134-C1, P6546001
#0155
o’ring/gasket kit
7419
Dia. - 3”
Lgth. - 9”
In/Out - 3/8” x 3/8” Male O’ring
Moisture Indicator
Mack 221RD44M
uses:
uses:
o’ring/gasket kit
o’ring/gasket kit
#0160
7421
Accumulator, w/o Aux AC, 2 ports
International 4000, 7000, 8000 Series
OE#: 3839360-C92
#0155 & #0160
7422
Accumulator, w/Aux AC, 3 Ports
International 4000, 7000, 8000 Series
OE#: 3843558-C92
515
RECEIVER DRIERS
7400
Side Sight Glass
Bottom High Press Switch
Top Moisture Indicator
Carrier 65-00193-00; 088599-01
7406
Universal Accumulator
Dia. - 3 1/2”
Lgth. - 8”
In - 3/4” #12 Female O’ring
Out - 3/4” #12 Female O’ring
(2) R12 Ports
GM 12322992
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
#6 = 3/8”
#8 = 1/2” #10 = 5/8” #12 = 3/4”
OUT
OUT
IN
IN
7427
Accumulator GM
Dia. - 3 1/2”
Lgth. - 9”
In - 3/4” Female O’ring
Out - 3/4” Male O’ring
(2) 1/4” Ports
OE# 2724802; 3090492
IN
OUT
7428
Accumulator GM
Dia. - 3 1/2”; Lgth. - 9”
In - #12 Female Insert O’ring
Out - #12 Male Insert O’ring
1/4” Male Switch Port
Male Charging Port
OE# 1131394, 2724260
OUT
IN
7430
Accumulator GM
Dia. - 3 1/2”; Lgth. - 9”
In - M27 x 2 5/8” Female O’ring
Out - M27 x 2 5/8” Male Insert O’ring
(1) M12 Port; (1) M13 R134a Port
OE# 2724665; 2724885
IN
RECEIVER DRIERS
OUT
7431
Accumulator GM
Dia. - 3 1/2”; Lgth. - 9”
In - 3/4” Female O’ring
Out - 3/4” Male Insert O’ring
(2) 1/4” Ports
OE# 1131506; 3059317
7434
Accumulator GM
Dia. - 3 1/2”; Lgth. - 8”
In - 3/4” Female O’ring
Out- 3/4” Male O’ring
(1) 1/4” Port
OE# 1131843; 2724542; 2724689
OUT
7440
Accumulator GM
Dia. - 3 1/2”; Lgth. - 9”
In -M27 Female O’ring
Out -M27 Male O’ring
(1) M12 Port; (1) M13 R134a Port
OE# 2724847
IN
IN
IN
OUT
OUT
7444
Accumulator GM
Dia. - 3 1/2”; Lgth. - 8”
In -M27 Female O’ring
Out -M27 MIO
(1) M12 Port
OE# 1132722; 2724924
7446
Accumulator GM
Dia. - 3 1/2”; Lgth. - 9”
In -M27 Female O’ring
Out -M27 Male O’ring
(1) M12 Port
OE# 2724817
7448
Accumulator GM
Dia. - 3 1/2”; Lgth. - 9”
In - 3/4” Female O’ring
Out - 3/4” Male Insert O’ring
(2) 1/4” Ports
OE# 2724194
OUT
IN
7450
Accumulator GM
Dia. - 3 1/2”; Lgth. - 9”
In - 3/4” Female O’ring
Out - 3/4” Male O’ring
(2) 1/4” Ports
OE# 2724804
516
# 0142
seals
7454
Accumulator Ford
Dia. - 3 1/2”; Lgth. - 10”
In - 5/8” Male Insert O’ring
Out - 3/4” Male Insert O’ring
(2) 1/4” Ports
OE# E7TZ-19C836A
7457
Accumulator GM
Dia. - 3 1/2”; Lgth. - 9”
In - Pad Type
Out - M27 Male Insert O’ring
(1) M12 Port
(1) 13mm R134a Port
OE# 15005371
© 2015 MEI Corporation
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
#6 = 3/8”
#8 = 1/2” #10 = 5/8” #12 = 3/4”
IN
IN
OUT
OUT
7459
Accumulator GM
Dia. - 3 1/2”; Lgth. - 9”
In - 3/4” Female O’ring
Out - 3/4” Male Insert O’ring
(2) 1/4” Ports
OE# 2724877
7466
Accumulator GM
Dia. - 3 1/2”
Lgth. - 9”
In - 3/4” Female O’ring
Out - 3/4” Male Insert O’ring
(1) M12 Port (1 3/4” below fittings)
OE# 2724475
OUT
IN
7466M
Accumulator GM
Dia. - 3 1/2”
Lgth. - 9”
In - M27 Female O’ring
Out - M27 Male Insert O’ring
(1) M12 Port (1 3/4” below fittings)
OE# 2724899
IN
OUT
IN
7469
Accumulator GM
Dia. - 3 1/2”
Lgth. - 9”
In - M27 Female O’ring
Out - M27 Male Insert O’ring
(1) M12 Port; (1) 13mm R134a Port
OE# 2724886
7479
Accumulator Ford
Dia. - 3 1/2”
Lgth. - 9 3/4”
In - 3/4” Male Insert O’ring
Out - 3/4” Female Springlock
(2) 1/4” Ports
OE# E6VY-19C836A
7480
Dia. - 2 1/2”
Lgth. - 8 1/4”
In/Out - 3/8” x 3/8” Male O’ring
Switch Port
7482
Accumulator Ford
Dia. - 3 1/2”
Lgth. - 8 3/4”
In - 5/8” #10 Male Springlock
Out - 3/4” #12 Male Springlock
(1) M10 Switch Port
(1) 13mm Chg Port
OE# F4UZ-19C836A
7483
Accumulator Ford
Dia. - 3”
Lgth. - 8”
In - 5/8” Male Insert O’ring
Out - 3/4” Male Insert O’ring
M12 Switch Port
13mm Charge Port
OE# F4TZ-19C836A; F6TZ-19C836AA
7485
Accumulator Ford
Dia. - 3 1/2”
Lgth. - 9”
In - 3/4” Male Springlock
Out - 3/4” Female Springlock
(1) M12 Port
(1) M13 R134a Port
OE# E49Z-19C836C
7486
Accumulator Ford
Dia. - 3 1/2”
Lgth. - 9”
In - 1/2” #8 Female Insert O’ring
Out - 3/4” #12 Female Insert O’ring
OE# F65Z-19C836AA
7487
Accumulator Ford
OE# F75Z-19C836AA
© 2015 MEI Corporation
RECEIVER DRIERS
OUT
517
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
#6 = 3/8”
#8 = 1/2” #10 = 5/8” #12 = 3/4”
RECEIVER DRIERS
# 0187
pad o’rings
7488
Accumulator
Ford F-Series
OE# F7UZ-19C836BB
7489
Accumulator Ford
OE# F75Z-19C836BA
7490
Accumulator Ford
OE# XL3Z-19C836AA
7493F
O.E. Style Ford Accum
Dia. - 3 1/2”
Lgth. - 8 1/8”
In - 5/8” #10 MIO
Out - 3/4” #12 MIO
OE# F6HZ-19C836A; F7HH-19E647AB;
4C4H-19C808AA
7493G
Aftermarket Style
Ford Accumulator
Dia. - 3 1/2”
Lgth. - 8 1/8”
In - 5/8” #10 MIO
Out - 3/4” #12 MIO
OE# F6HZ-19C836A
7494
Accumulator Ford
OE# XL3Z-19C836BA
Must reuse old housing or
use #7496A which includes
the housing.
PlP
# 0187
pad o’rings
# 0187
pad o’rings
7495
Accumulator
Ford Truck E Series
OE# 2C2Z-19C836BA
7496
Accumulator Ford
Dia. - 3 1/2”
Lgth. - 8 7/8”
In - PAD
Out - 3/4” #12 Female Insert O’ring
OE# F81Z-19C836AA
7496A
Accumulator - includes
plastic housing
Dia. - 3 1/2”
Lgth. - 8 7/8”
Ford F250/350
OE# 6C3Z-19C836A
OUT
7498
Accumulator Ford
Dia. - 4”
Lgth. - 10 1/4”
In - PAD
Out - 3/4” Female Insert O’ring
M10 Switch Port
(2) 13mm Charging Ports
OE# F85Z-19C836AB
518
use # 0170
special o’rings
(not supplied)
7500
Dia. - 2 1/2”
Lgth. - 7”
In/Out - 1/2” x 1/2” Male Flare
16 cu.in. In-Line Filter Drier
OE# WAH164FO
IN
7501
Dia. - 2 1/2”
Lgth. - 6 3/4”
In/Out - 3/8” x 3/8” Male Flare
16 cu.in. In-Line Filter Drier
OE# WAH163
© 2015 MEI Corporation
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
#6 = 3/8”
#8 = 1/2” #10 = 5/8” #12 = 3/4”
OUT
# 0077
o’rings
IN
7503
Dia. - 2 1/2”
Lgth. - 6 3/4”
M18 Inlet x M20 Outlet
Male O’ring, In-line Design
GMC OE# 15982368
IN
IN
OUT
# 0011
o’rings
IN
OUT
OUT
fine thread
check valve
1/2”-20
course thread
check valve
7514
Dia. - 2 1/2”
Lgth. - 6 5/16”
In - M18 Male
Out - Fine Thread
(1) M10 Port
Top Sight Glass
OE# 33-0382A; 088370-0
7513
Dia. - 2 1/2”
Lgth. - 6 5/16”
In - 3/8” Male O’ring
Out - 1/2”-20 Course Thrd
(1) M10 Port
Top Sight Glass
OE# 33-0038A; 085623-00
IN
IN
7504
Dia. - 2 1/2”
Lgth. - 7”
In/Out - 1/2” x 1/2” Male Flare
16 cu. in. In-Line Drier
OE# WAH 164
OUT
RECEIVER DRIERS
7502
Dia. - 2 1/2”
Lgth. - 10”
In/Out - 3/8” x 3/8”
Male O’ring
Red Dot remote condenser
7515
Dia. - 2 1/2”
Lgth. - 6 5/16”
In - M18 Male
Out - M18 Male
(1) M10 Port
Top Sight Glass
OE# 33-0383A; 088371-00
OUT
IN
OUT
fine thread
check valve
7517
Dia. - 3 3/4”
Lgth. - 10 3/4”
In/Out - 1/2” x 1/2” Male Flare
41 ci.in. dessicant
TYPE AH414 In-LineDrier/TransAir A/C
7519
Dia. - 2 1/2”
Lgth. - 6 5/16”
In - M18 Male
Out - Fine Thread
M10 Switch Port
Top Sight Glass
GM Chasis Motor Home
OE# 085686-00
7524
Dia. - 2 1/2”
Lgth. - 6.32”
In/Out - M18 Male
M10 Switch Port
Top Sight Glass
OE# 085722; RV218337
OUT
IN
OUT
#0011
o’rings
7532
Dia. - 2 1/2”
Lgth. - 5.9”
3/8” x 3/8” Male O’ring
Top Sight Glass
Side Fuse Plug
Port 3/8” O’Ring
OE# 085428-00
© 2015 MEI Corporation
7540
Dia. - 3”
Lgth. - 10”
In/Out 1/2” x 1/2” Male Flare
30 cu.in. In-Line Filter Drier
OE# EK 304
IN
519
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
#0013
o’rings
IN
#6 = 3/8”
IN
OUT
OUT
# 0017
o’rings
use # 0170
special o’rings
(not supplied)
7541
Dia. - 2 3/4”
Lgth. - 8 1/2”
In/Out - 1/2” x 1/2” Male Insert O’ring
16 cu.in. In-Line Filter Drier w/sight glass
CARRIER OE# 14-00288-00; WSG 164 MIO
RECEIVER DRIERS
#8 = 1/2” #10 = 5/8” #12 = 3/4”
7543
Accumulator
Dia. - 3 1/2”
Lgth. - 9 1/8”
In - 1 1/16” Female O’ring
Out - 1 1/16” Female O’ring
CAT OE# 1018789 (Steel)
7542
Dia. - 2 3/4”
Lgth. - 8 1/2”
In/Out - 1/2” x 1/2” Flare O’ring
16 cu.in.In-Line Drier w/sight glass
OE# WSG164 FO
# 0135
o’rings
# 0017
o’rings
7544
Accumulator
Dia. - 3 1/2”
Lgth. - 9 13/16”
In - 1 1/16” Female O’ring
Out - 1 1/16” Female O’ring
CAT OE# 089320-00; 197-6218
# 0011
o’rings
7546
Dia. - 2 1/2”
Lgth. - 10”
Pad Type Drier
KUBOTA 3F999-10740
Komatsu 20Y-979-320
CAT OE# 176-1902
7545
Dia. - 3”
Lgth. - 10 1/2”
Pad Type Drier
with 16mm port
VOLVO OFF-ROAD OE# 11104567
IN
OUT
IN
OUT
# 0011
o’rings
# 0013
o’rings
7548
Dia. - 3”
Lgth. - 10”
30 cu. in. In-Line Filter Drier w/sight glass
In/Out - 1/2” SAE
Carrier OE# WSG304
7547
Dia. - 2 1/2”
Lgth. - 7”
Pad Type Drier
CAT OE# 113-3497
IN
7549
Dia. - 3”
Lgth. - 11 1/2”
30 cu. in. In-line Filter Drier w/sight glass
In/Out - 1/2” Male Insert O’ring
Carrier OE# ADK304; WSG304MOI
OUT
# 0142
#12 stat seals
7551
Dia. - 3”
Lgth. - 10 1/2”
30 cu. in. In-line Filter Drier
In/Out - 5/8” SAE
Carrier OE# WAH305
520
7552
Accumulator Ford
2011-2007 E-Series w/diesel engine
OE# 7C2Z-19C836AA
7554
Accumulator
In/Out - #12 Stat Seals
2006-2003 Topkick/Kodiak
OE# 1132813
© 2015 MEI Corporation
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
#6 = 3/8”
#8 = 1/2” #10 = 5/8” #12 = 3/4”
OUT
IN
# 0011
o’rings
# 0110
o’rings
7555
Dia. - 3”
Lgth. - 6 1/2”
In/Out - 3/8” x 3/8” Male O’Ring
Top Sight Glass,
P.R.V. & Moisture Indicator
OE# RD5-9419-0
7557
Dia. - 1 5/8”
Lgth. - 11 5/8”
Pad Style Drier
2007-08 Sprinter Van
OE# 680-013634AA
7556
Pad Style Drier
2003-06 Sprinter Van, 2.7TD
051-03570AA
# 0142
#12 stat seals
7558
Accumulator
In/Out - #12 Stat Seals
2003-2008 GMC G Series
OE# 25760829
# 0131
#8 stat seals
7559
Dia. - 4”
Lgth. - 7”
In/Out - #8 Stat Seals
Freightliner Columbia, M2
OE# A22-63992-000; A22-63992-001
OUT
7560
Dia. - 2 1/2”
Lgth. - 7 3/4” (13.88” OAL)
MIO fittings with orifice tube
CAT OE# 257-3227
IN
IN
# 0131
#8 stat seals
7561
Dia. - 4”
Lgth. - 7”
In/Out - #8 Stat Seals
Freightliner
OE# A22-63993-001; A22-65550-000
7562
Dia. - 2 5/8”
Lgth. - 7 1/2”
In - 3/8” #6 Male O’ring
Out - 3/8” #6 Female O’ring
16 cu. in. dessicant In-Line Drier
Pressure Relief Vavle
Kysor OE# 402618
7565
Dia. - 4”
Lgth. - 6 3/4”
In/Out - 3/8” x 3/8”
Male O’ring
Side Sight Glass
Fuse Plug
Volvo Off Road VRE
OE# RD5-6075-0
© 2015 MEI Corporation
7564
Dia. - 3”
Lgth. - 14.35”
#6 Spring Lock Connections
Moisture Indicator
Ford New Holland OE# 89154-00
# 0131
#8 stat seals
7566
Dia. - 4”
Lgth. - 7”
In/Out - #8 Stat Seals
Freightliner Coronado
A22-63994-001
521
RECEIVER DRIERS
OUT
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
#6 = 3/8”
#8 = 1/2” #10 = 5/8” #12 = 3/4”
3/8”-24
Port
M10
Port
# 0025
o’rings
7567
Dia. - 3”
Lgth. - 10”
In - 3/8” Male O’ring
Out - 3/8” Male O’ring
Western Star 088586-00
# 0025
o’rings
7569
Pad Type Drier
(will replace Type 1 Driers)
Dia. - 2.9”
Lgth. - 9”
Linkbelt Excavator
OE# YT54500003P1
7568
Pad Type Drier
Dia. - 2.4”
Lgth. - 10”
CAT# 176-1902
Type 2
RECEIVER DRIERS
female port
12.45mm
Port
female port
12.45mm
Port
7570........... 3/8” x 3/8” MIO
7570M.........14mm Metric Threads
Dia. - 2.6”
Lgth. - 11 3/8”
(2) Female Ports
HINO TRUCK
7571
Dia. - 2-3/4”
Lgth. - 10”
12.45mm Ports
Pad Type Drier
MITSUBISHI FUSO
7572
Dia. - 4”
Lgth. - 7 3/4”
In - #6 Female O’ring
Out - #6 Male Insert O’ring
CASE TRACTOR
OE# 86984155
7573
Dia. - 3”
Lgth. - 11 1/2”
In - #6 Female O’ring
Out - #6 Male Insert O’ring
J. Deere OE# RE214440, 088545-00
7574
Dia. - 3”
Lgth. - 11 1/2”
In - #6 Female O’ring
Out - #6 Male Insert O’ring
J. Deere OE# AL163559, 088549-00
7575
Dia. - 4”
Lgth. - 7”
In - #6 Female O’ring
Out - #6 Male Insert O’ring
J. Deere OE# AL162467
IN
7576
Accumulator
Dia. - 3 1/2”
Male x Female
J. Deere, 670D Grader
OE# 803-465, AT190809
522
OUT
7577
Dia. - 3”
Lgth. - 10”
Male x Female
Top Sight Glass
Ford/New Holland
OE# 803-380, 82012480
# 1418
switch
# 0187
pad o’rings
#12 o’rings
Springlock
7578
Accumulator w/Hose
Ford 2008-09
OE# 8C3Z-19C836C
© 2015 MEI Corporation
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
#6 = 3/8”
#8 = 1/2” #10 = 5/8” #12 = 3/4”
R134a
Port
7580
R134a Port
3/8” Male Insert O’ring
Volvo Loader OE# 20490945
7583
Accumulator
Ford E-Series
OE# 7C2Z-19C836B
7584
GMC C/K 10-35 Series
(2nd design)
Dia. - 3 1/2”
Lgth. - 8”
(1) Male Pad
(1) Female Pad
R134a Charge Port
M12 Switch Port
OE# 15827280; 1411812
7585
Freightliner Cascadia
OE# 22-66700-000
7586
Freightliner M2
OE# A22-66600-000
7587
Ford 2008-2010
F250 / 500SD w/gas engine
OE# 8C3Z-19C836B
7588
Accumulator
(13-1/4” x 7-1/2”)
13mm Charge Port
Ford Transit-connect
OE# 9T1Z-19C836A; YF3625
7592
Pad Mount Drier
Dia. - 2-3/8”
Lgth. - 7-1/2”
VOLVO Excavators, EC Series
OE# 14509377
# 0131
sealing
washers
RECEIVER DRIERS
7579
Volvo Construction A25B
OE# 11005931
# 0131
sealing
washers
OUT
7593
Dia. - 3”
Lgth. - 6-1/4”
In/Out - 3/8” x 3/8” Male O’ring
Female Switch Port
Pressure Relief Valve
Top Sight Glass
TEREX Wheel Loader SKL863, SKL873
© 2015 MEI Corporation
7594
Dia. - 3”
Lgth. - 6-1/2”
In - #6 Male O’ring
Out - #6 Male O’ring
Male Switch Port
CAT Exv., M318 / FNH Excavator EC270
OE# 73186213
7595
Accumulator w/o desiccant
Dia. - 3-1/2”
Lgth. - 9-3/4”
In/Out - #12 Female O’ring
(1/16” -16 thread)
CAT Construction Equip.
OE# 186-6189
IN
523
RECEIVER DRIERS
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
#6 = 3/8”
#8 = 1/2” #10 = 5/8” #12 = 3/4”
7596
Dia. - 3”
Lgth. - 10-1/2”
In - #6 Male O’ring
Out - #6 Female O’ring
Switch Port, 7/16” Male Flare
Side Sight Glass
Top Mount Bracket
FNH Backhole 555E-675E
OE# 85804063
7597
Dia. - 4”
Lgth. - 8-1/2”
In - 3/8” Female O’ring
Out - 3/8” Male O’ring
Combines, Forage Harvesters, Telehandlers
OE# AZ45582
7598
Drier Cartridge
Ford F250-550SD, 6.7L Diesel
OE# BC3Z-19C836A
7599
Pad Mount Drier w/Trinary Switch
Dia. - 2-1/2”
Lgth. - 9”
GMC/ISUZU
OE# 8-98039-052-0
7601
Drier/element
ISUZU
OE# 1-83535-097-0
7602
Drier/pad type
ISUZU
OE# 8-97366-991-0
IN
OUT
7603
Drier
ISUZU
OE# 8-97308-332-0
7604
Drier
ISUZU
OE# 1-83535-068-0
IN
7606
Drier
ISUZU
OE# 8-97175-137-0
524
IN
OUT
7605
Drier
ISUZU
OE# 8-97183-124-0
IN
7607
Drier/pad type
ISUZU
OE# 8-97118-190-1
OUT
OUT
7608
Drier/pad type
ISUZU
OE# 1-83535-095-0
© 2015
© 2015
MEIChad/Preston
Corporation
RECEIVER DRIERS
#6 = 3/8”
#8 = 1/2” #10 = 5/8” #12 = 3/4”
7609
Drier w/switch
ISUZU
OE# 1-83535-080-0
7611
Drier Element
Ford F250-550SD
6.2V8 Gas, 6.7L Diesel
OE# BC3Z-19C836B
7612
Dia. - 3”
Lgth. - 10-1/2”
In/Out - #6 x #6 MIO
(1)1/4” Male Port
(2) 1/4” Female Ports
Side Sight Glass
Volvo Offroad
OE# 1089855
7613
Drier
J.Deere / Liebherr / Terex
5821662227
7614
Drier (steel)
Dia. - 2-1/2”
Lgth. - 8”
In/Out - MIO, M18 metric
Top Sight Glass
Side Switch
Doosan Excavator DX255LC
OE# 2204-6039A
7615
Drier (aluminum)
Dia. - 2.38”
Lgth. - 9-1/2”
In/Out - PAD
Kubota Tractor
OE# T2055-72230
RECEIVER DRIERS
NOTE: Drier mfg’s have discontinued using moisture indicators.
We will supply moisture indicators where applicable while supply lasts.
Universal Drier and Fitting KIT - great for service trucks
Allows the use of Standard or Metric Charge Port Fittings
Has Multiple Charge Ports
for use with #8999 Fitting Kit
7600
Dia. - 2 1/2”
Lgth. - 8”
In - 3/8” Male O’ring
Out - 3/8” Female O’ring
Top Sight Glass
Moisture Indicator
(3) 3/8”-24 Female Switch Ports
© 2015 MEI Corporation
8999
Universal Drier Fitting Kit
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
P/N
Qty. Description
0011 ......... 10.......... 3/8” O’rings
4136 .......... 1 .......... 3/8” MOR to 3/8” MIO drier adapter
4137 .......... 1 .......... 11/16” MOR to 3/8” MIO drier adapter
4161 .......... 1 .......... 3/8”-24 male to M10 sw. port adapter
4162 .......... 1........... 3/8”-24 male to 12mm metric adapter
4165 .......... 1........... 3/8”-24 to 13mm charge port adapter
4166 .......... 1........... 3/8”-24 to 16mm charge port adapter
4167 .......... 1........... 7/16” FF to M10 Male sw. port adapter
4168 .......... 1........... M10 FF to 7/16” MF, R12 flare adapter
4913 .......... 2 .......... 3/8” MOR to Flare adapter
4922 .......... 2 .......... 3/8” MOR to 3/8” FF adapter
5527A ....... 1 .......... 3/8” MOR, 3/8” FOR, R12 Inline Chg Ftg.
5685 .......... 1 .......... 3/8”-24, Pressure Relief Valve
8900 .......... 2 .......... 3/8”-24 male thrd. to 7/16” MF, R12 adpt.
8915 .......... 5........... Std. Valve Cores R12/R134a
525