Fseries Frequency,Tacho,Counting,Batch Meter
FH series Inteligent Frequency/Counting/Length/Height/Linespeed Integreted Meter
Fseries Frequency,Tacho,Counting,Batch Meter
FH series Inteligent Frequency/Counting/Length/Height/Linespeed Integreted Meter
MYPIN
MYPIN
Features
Press button setting,can measuring various frequency,tacho,linespeed,with counting,length function at the same time
2 segment optional parament setting,optional frequency dividing,length parameter setting
INPUT/OUTPUT opical isolation,high anti-interference
2 road input with ADD/subtract function,can match with various encoder.
4 digit/ 6 digit LED display,sensor power supply
2 Alarm Output,several output mode selectable.
one analog current output with various measuring signal selectable(in frequency measuring state)
FH8
FH7
RS485 communication interface,MODBOS RTU protocol selectable
AC
90-260V
NO
12
11
9
10
8
7
6
5
4
2
←
←
3
1
RST
NC
OUT1
OUT2
FH8
12V RST GND INB INA
Code Illustration
MFH□□-□□□□□□
Signal input:
Blank:universal
2:others
Power supply:
A:12V B:24V
Communication:
Blank:without
2:RS232 4:RS485
OUT2
Dimension
Mode
80
Input Mode A,B,C,D Counting
N:without
R:RELAY
Size
Installing
Dimension
S:SSR/LOGIC
OUT1 N: without
R:RELAY
S:SSR/LOGIC
T:SCR
Input Mode B UP/DOWN(add/subtract)
Input Mode A UP(add)
Input Counting
T:SCR
Controllor Terminal
Input Counting
Controllor Terminal
Digits display:
:
4:4 digits
6:6 digits
Size:
4：48H×48W
7：72H×72W
INB at high level,INA inpur not allown;
INB at low level,INA at UP counting
8：48H×96W
Input Mode C UP/DOWN(add and subtract
Input Counting
MFH series count/tacho multi-meter
Technical Parameter
Pulse signal: square wave and
0≤L≤2V up edge active
INA for Count,INB for frequency,Please short connect INA and INB
if only one output is needed.
Insulation
resistance
≥20MΩ
Consumption:＜5W
Power supply 90-260V AC/DC or 15-30V AC/DC
www.mypinchina.com
3
9
INA
4
10
RST
5
11
+12V
AL1
NC
NO
6
90-260V
AC
INB
OUT1
90～260V
AC
8
12
FH4
1
10
INA
2
11
INB
3
12
RST
NO
13
GND
5
14
+12V
6
15
7
16
8
17
9
18
4
NC
OUT2
SCR
←
SSR
Contact relay
250V AC/3A or 30V DC/5A resistance load
capacity
Operation
0～50℃ 35～85%RH
environment
←
RELAY
30mA max
2
←
24V/12VDC ± 10%
GND
RST
（According to the display digit）
0.00001-999999
7
RST
Output type
（According to the display digit）
-199999-999999
1
←
Counting speed 30/5000CPS
Auxiliary power
Input Mode D UP/DOWN (phase difference input,used as Encoder)
Input Counting
Input Counting
NO
NC
FH7
Counting Value
Counting Value
INA:UP countiing terminal
INB:DOWN counting terminal
Input impedance ≥10KΩ
Preset
range
Input Counting
INA at high level,INA at DOWN counting
INB at high level.INB at UP counting
Connection
Input signals sine wave ：5≤H≤30V
Counting
range:
Counting Value
Counting Value
Power:
Blank:90-260V AC 50/60HZ
E:15-30V AC/DC
Input Mode Selection
Input Mode
Mode
Mode
Mode
Mode
INA Signal advance INB Signal,UP counting active;
INA Signal lagging dehind INB Signal,DOWN counting active;
Function Illustration
INA: UPcounting,INB:GATE function,If INB is high level or short connected with +12V,INA Input is not allown
INA:UP counting,INB:Countdown control function,If INB is high level,INA changes to DOMN counting
INA:UP counting, INB:DOWN counting
INA Signal advance INB Signal,UP counting active; INA Signal lagging dehind INB Signal,DOWN counting active;
Output Mode Selection
Output Mode
Mode
Mode
Mode
Mode
Mode
Mode
Function Illustration
UP count to setting value HI , display value delay some time ,and reset automatically(we call it Automatic Reset)
UP count to setting value HI , display value delays until reset handly or extra connection we call it Manual Reset
UP count to setting value HI , display value reset automatically and count again(we call it Automatic Reset)
UP count to setting value HI , display value continue to add,untill manual reset or extra connection
UP count to setting value HI , HI and LO act as the first and second segment Output Controllor respectively
HI and LO act as High limit and Low limit Alarm Output Controllor respectively
www.mypinchina.com