TRANSFORMERS
Remote Transformer
DUAL-FEED, 12 VOLTS 600 WATTS
tran_at600t_spec.pdf
DESCRIPTION
This remote magnetic transformer converts standard 120 volt line
voltage to 12 volts, providing the necessary voltage for powering
a MonoRail, Kable Lite, TwinRail, Wall MonoRail or FreeJack lowvoltage lighting system. This remote magnetic transformer can be
used to power lamps totaling up to 600 watts. This transformer is
equipped with fast-acting secondary circuit breaker that will safely
turn off the system should a short occur. Once the short has been
removed the breaker can be reset.
Shown approximately 10% actual size.
6.1”
155 mm
5.1”
130 mm
11.5"
292 mm
INSTALLATION
This transformer must be installed in a remote but accessible
location (such as above the ceiling or in a closet). To simplify
installation the transformer should be located no more than 20 feet
from the run or power feed. The electrician will need to supply the
proper gauge conductor from the transformer to the power feed
location based on distance (see voltage drop chart, below).
DIMMING
Dimmable with a 1000 watt low-voltage magnetic dimmer. The
dimmer is placed on the line side of the transformer. (Consult
dimmer manufacturer for specifics.) Dimming a transformer may
create a buzzing sound, which may be objectionable in some
applications. A debuzzing dimming coil can be purchased
separately to reduce the audible noise.
OPTIONS
Input Wiring: Can be ordered to hard wire to a junction box or to
plug in with 16 foot power cord with inline switch, two feet from
the plug. Also available with 277 volt input.
REQUIRED USAGE
This transformer provides two 300 watt outputs and must be used
with a dual-feed canopy or two other power feed options (sold
separately). 12 volt output transformers require the use of 12 volt
lamps.
WEIGHT
17.42 lb./7.90 kg. ±
VOLTAGE DROP CHART
Use to determine the correct THHN wire size for a recommended 3 percent drop
in voltage at the specified wattage. The length shown is the length of wire from
the transformer to the power feed.
12 Volt
300 Watt
5 ft.
6-15 ft.
16-20 ft.
21-40 ft.
41-60 ft.
61-90 ft.
#10 GA
#6 GA
#4 GA
#1 GA
1/0
3/0
ORDERING INFORMATION
700AT600
INPUT WIRING
T
HARD WIRE 120V
T277 HARD WIRE 277V
P
PLUG IN 120V
700AT600 _______
FIXTURE TYPE: _________________________________________
7400 Linder Avenue
Skokie, Illinois 60077
T 847.410.4400
F 847.410.4500
JOB NAME: _____________________________________________
www.techlighting.com
© 2007 Tech Lighting, L.L.C. All rights reserved. The "Tech Lighting" graphic is a registered trademark of Tech Lighting, L.L.C.
Tech Lighting reserves the right to change specifications for product improvements without notification.
TRANSFORMERS
Remote Transformer
SINGLE-FEED, 24 VOLTS 600 WATTS
tran_at6024t_spec.pdf
DESCRIPTION
This remote magnetic transformer converts standard 120 volt line
voltage to 24 volts, providing the necessary voltage for powering
a MonoRail, Kable Lite, TwinRail, Wall MonoRail or FreeJack lowvoltage lighting system. This remote magnetic transformer can be
used to power lamps totaling up to 600 watts. This transformer is
equipped with fast-acting secondary circuit breaker that will safely
turn off the system should a short occur. Once the short has been
removed the breaker can be reset.
Shown approximately 10% actual size.
6.1”
155 mm
5.1”
130 mm
11.5"
292 mm
INSTALLATION
This transformer must be installed in a remote but accessible location
(such as above the ceiling or in a closet). To simplify installation the
transformer should be located no more than 20 feet from the run or
power feed. The electrician will need to supply the proper gauge
conductor from the transformer to the power feed location based on
distance (see voltage drop chart, below).
DIMMING
Dimmable with a 1000 watt low-voltage magnetic dimmer. The
dimmer is placed on the line side of the transformer. (Consult dimmer
manufacturer for specifics.) Dimming a transformer may create a
buzzing sound, which may be objectionable in some applications.
A debuzzing dimming coil can be purchased separately to reduce the
1
audible noise.
OPTIONS
Input Wiring: Can be ordered to hard wire to a junction box or to
plug in with 16 foot power cord with inline switch, two feet from the
plug. Also available with 277 volt input.
REQUIRED USAGE
This transformer provides a single 600 watt output and must be used
with a single-feed canopy or other power feed option (sold
separately). 24 volt output transformers require the use of 24 volt
lamps.
WEIGHT
17.04 lb./ 7.72 kg. ±
VOLTAGE DROP CHART
Use to determine the correct THHN wire size for a recommended 3 percent drop
in voltage at the specified wattage. The length shown is the length of wire from
the transformer to the power feed.
24 Volt
600 Watt
5 ft.
6-15 ft.
16-20 ft.
21-40 ft.
41-60 ft.
61-90 ft.
#12 GA
#8 GA
#6 GA
#4 GA
#2 GA
#1 GA
ORDERING INFORMATION
700AT6024
INPUT WIRING
T
HARD WIRE 120V
T277 HARD WIRE 277V
P
PLUG IN 120V
700AT6024 _______
FIXTURE TYPE: _________________________________________
7400 Linder Avenue
Skokie, Illinois 60077
T 847.410.4400
F 847.410.4500
JOB NAME: _____________________________________________
www.techlighting.com
© 2007 Tech Lighting, L.L.C. All rights reserved. The "Tech Lighting" graphic is a registered trademark of Tech Lighting, L.L.C.
Tech Lighting reserves the right to change specifications for product improvements without notification.