J-145
3 Channel Keyless Entry
Wiring Diagram
White
Red
L.E.D.
GREEN
BLUE
LOCK Unlock
1
2
3
4
5
Red
White
9
10
11
12
13
14
Valet
NOT
Switch
USED
(+) POWER
(+) PARKING LIGHTS
(+) SIREN OUTPUT
Blue/White
(-) PASSENGER DOOR UNLOCK
White/Red
Orange
8
White
Brown
6
7
Blue
Brown/White
Black/White
Blue
Gray
Yellow
(-) 3 RD. CHANNEL
(-) OUTPUT (Starter Kill)
(-) HORN OUTPUT
(-) DOME LIGHT
NOT USED
(-) 2nd CHANNEL (Trunk)
(+) IGNITION
Black
(-) GROUND
Violet
(+) DOOR INPUT
Green
(-) DOOR INPUT
14 Pin Connector
Red Wire: Main power input. Connect this wire to a good 12 volt (+) constant
source that can support the 15 amp current draw necessary for correct operation
of the system.
White Wire: Parking light output. Connect this wire to the vehicle parking light
circuit. This wire supplies a 12 volt (+) output.
Brown Wire: Siren output. Connect this wire to the RED wire of the siren.
Connect the BLACK wire of the siren to chassis ground. **Warning** This wire is
designed to operate (1) siren only. Use a relay to drive additional sirens or other
devices. Failure to this warning instruction may damage the siren circuit and
void the manufacturerís warranty.
Blue/White Wire:(-) Passenger door unlock
White/Red Wire:(-)Auxiliary channel 3) output. This wire supplies a 250 mA
negative (-) output when the ë Remote starter units, etc.(1)í button is pressed and
held for 1.5 seconds.
Orange Wire: Ground while armed output. This wire supplies a 500 mA negative
(-) output when the system is armed. Use this output to operate window roll-up
modules, additional starter interrupts, etc.
Brown/White Wire: Factory horn honk output. This wire supplies an on-off
pulsing ground (-) output when the system has been triggered.**Note** A relay
must be used to activate the factory horn circuit.
Black/White Wire:(-) Dome light
Blue Wire:(Not Used)
Gray Wire: Trunk release (Auxiliary channel 2) output. This wire supplies a 250
mA negative (-) output when the ëTRUNK (3)í button is pressed and held for 1.5
seconds. This output can be used to operate truck release motors. **Note** In
most cases a relay must be used with this output.
Yellow Wire: Ignition power input. Connect this wire to an ignition power source
that supplies 12 volt (+) when the vehicle ignition switch is in the ëONí or ëRUNí
position.
Black Wire: Chassis ground. Connect this wire securely to a clean, solid,
negative (-) chassis ground (firewall or kick panel). This connection is crucial for
proper operation of the system.
Violet Wire: Positive (+) door input. Connect this wire to the vehicle pin switch or
circuit that supplies a positive (+) voltage when the door(s) is opened.
Green Wire: Negative (-) door input. Connect this wire to the vehicle pin switch
or circuit that supplies a negative (-) voltage when the door(s) is opened.
LED (Red 2-pin connector):
Plug-In status LED. (Supplied with system)
Valet Switch (Blue 2-pin connector):
Plug-In Valet switch. (Supplied with system)
Remote Programmable Features:
To enter program mode.
1- Turn Ignition key ON
2- Within 10 seconds press push button switch 5 times. Horn will chirp
Lights And LED Will flash 5 times system is now in program mode.
To change any feature:
1- Press the switch same number of times as the change you wish to
make.
EXAMPLE: To change feature #3 press VALET switch ON OFF 3 times.
(Every time you press the switch lights will flash one time.)
2- Press button #1 on remote to turn feature ON LED will flash one time.
By pressing button #2 turns feature OFF LED flash 2 times.
PROGRAM LOCATIONS
FACTORY DEFAULT MODE # 1
MODE # 2
#1 IGNITION AUTO LOCK
NO IGNITION AUTO LOCK
#2 1 PULSE FOR UNLOCK
2 PULSE FOR UNLOCK
#3 HORN CONFORMATION
NO HORN CONFORMATION
#4 1 Sec. LOCK/UNLOCK PLS 3.5 Sec. LOCK/UNLOCK Pulse
#5 ACTIVE LOCK
PASSIVE LOCK
#6 IGNITION TRIGGER OFF
IGNITION TRIGGER ON
#7 NORMAL HORN CHIRP
EXTENDED HORN CHIRP
RESET TO FACTORY DEFAULT SETTING:
ENTER PROGRAM MODE (SEE ABOVE) PRESS AND HOLD BUTTON
# 3 FOR 5 SECONDS LED WILL FLASH 3 TIMES .AND ALL PROGRAMMABLE
FEATURES WIL GO BACK TO FACTORY DEFAULT SETTINGS.
CODE TEACHING:
Turn the ignition key 3 times on/off, on/off, on, the horn will chirp.Leave
the ignition key in on position, press the valet switch and hold until the
horn chirps/LED flash 3 times, Then press button # 1 on the remote
transmitter. The horn will chirp/LED flash once, if you want to teach
another transmitter with different code press # 1 on the second
transmitter the horn will chirp/LED flash once. You can teach 4 different
codes.
rev 04.9.1