INSTALLATION INSTRUCTIONS
Architectural Wall Mounts
54-113174-00E
IMPORTANT: Read all instructions before performing any work. Be sure all
power is off prior to installing luminaire.
WARNING:
Luminaire must be grounded in accordance with appropriate
codes. Failure to do so may result in serious injury.
SM
SR
SS
VR1
VR2
INSTALLATION INSTRUCTIONS:
1. Ensure power is not on before installing fixture.
2. Fixture is intended to be installed over a standard electrical gang box or junction box by qualified personal OR state
qualified electrician per electrical codes.
3. Wire fixture per instructions listed below.
LINE VOLTAGE INSTRUCTIONS:
1. Fixture requires a 4 inch by 4 inch electrical gang box/junction box that is a minimum 2.25 inches deep to be preinstalled into
wall, with line voltage wiring in place.
2. Install anchors into wall (by others) for #10 screws. Anchors MUST be level, centered with opening in wall, 5 inches on center.
3. Assembly mounting hardware and gasket provided with fixture as shown prior to wiring fixture.
4. Connect White, Black and Ground wires to proper mating wires using wire nuts or other approved method. Connections must
meet all electrical codes.
5. Install screws provided into anchors, ensure screws are fully tightened.
6. Inspect fixture after installation. Fixture must be level for proper performance. Gasket must fill any gaps to protect from
moisture and debris.
NOTE:
This fixture is intended for installation in accordance with the National Electric Code and local code specifications. Failure to adhere to these codes and instructions
may result in serious injury and/or damage to fixture, voiding the warranty. These instructions do not purport to cover all details or variations in equipment, nor to
provide for every possible contingency related to installation, operation, maintenance, or mounting. Should specific problems occur that are not addressed by these
instructions, contact your local sales representative or distributor for assistance. Retain these instructions for future reference.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE OR INJURY TO PERSONS:
Lighted fixture is hot. To reduce risk of injury to persons, turn fixture off or unplug and allow to cool before handling.
© 2012 Illumitex Inc. All rights reserved. The information in this document is subject to change without prior notice.
Illumitex Inc. | 5307 Industrial Oaks Blvd., Ste. 100 | Austin, TX 78735 USA | +1 512 279 5020 | www.illumitex.com
INSTALLATION INSTRUCTIONS
Architectural Wall Mounts
54-113174-00E
IMPORTANT: Read all instructions before performing any work. Be sure all
power is off prior to installing luminaire.
WARNING:
Luminaire must be grounded in accordance with appropriate
codes. Failure to do so may result in serious injury.
Step 1: Align fixture over previously installed electrical gang box/junction box, ensuring it is centered and
fully covering opening. Use mounting plate as a template to mark locations for wall anchors (by others).
Check markings for level. Lighting fixture must be level for proper performance. Use appropriate anchors for
mounting conditions. The Architectural Wall Mount fixtures are designed for #10 Counter Sink Screws.
View shows fixture properly placed,
Covering opening, centered and level.
Electrical gang box / junction box.
Must comply with all electrical codes
Use mounting holes as template for
marking drill locations.
Step 2: Install anchors into wall (by others) for #10 screws. Anchors MUST be level, centered with
opening in wall, 5 inches on center. Use appropriate anchors for mounting conditions.
Prior to drilling confirm drill spots
are level and centered with opening
Use appropriate anchors for
mounting conditions (not provided).
Fixture is designed to work with #10
counter sink screws.
NOTE:
This fixture is intended for installation in accordance with the National Electric Code and local code specifications. Failure to adhere to these codes and instructions
may result in serious injury and/or damage to fixture, voiding the warranty. These instructions do not purport to cover all details or variations in equipment, nor to
provide for every possible contingency related to installation, operation, maintenance, or mounting. Should specific problems occur that are not addressed by these
instructions, contact your local sales representative or distributor for assistance. Retain these instructions for future reference.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE OR INJURY TO PERSONS:
Lighted fixture is hot. To reduce risk of injury to persons, turn fixture off or unplug and allow to cool before handling.
© 2012 Illumitex Inc. All rights reserved. The information in this document is subject to change without prior notice.
Illumitex Inc. | 5307 Industrial Oaks Blvd., Ste. 100 | Austin, TX 78735 USA | +1 512 279 5020 | www.illumitex.com
INSTALLATION INSTRUCTIONS
Architectural Wall Mounts
54-113174-00E
IMPORTANT: Read all instructions before performing any work. Be sure all
power is off prior to installing luminaire.
WARNING:
Luminaire must be grounded in accordance with appropriate
codes. Failure to do so may result in serious injury.
Step 3: Install #10 counter
Step 4: After gasket has been assembled then
sink mounting screws into fixture
and gasket as shown prior to
wiring fixture.
connect white, black and ground wires to
incoming supply wires using wire nuts or other
approved method. Connections must meet all
electrical codes.
Step 5: Tighten screws into wall anchors. Use caution that wires do not get pinched, ensuring they are
properly placed inside electrical box. Fixture will be provided with an “UP” indicator label for proper
installation. Remove label once installed.
Remove label once fully installed.
Step 6: Fully inspect fixture. Check that fixture is level. Check for any exposed or pinched wires. Verify
gasket is fully compressed and sealing against wall. If any gaps are present then caulk or sealer may need
to be added. Failure to properly seal fixture and wall may result in serious injury and/or damage to fixture.
NOTE:
This fixture is intended for installation in accordance with the National Electric Code and local code specifications. Failure to adhere to these codes and instructions
may result in serious injury and/or damage to fixture, voiding the warranty. These instructions do not purport to cover all details or variations in equipment, nor to
provide for every possible contingency related to installation, operation, maintenance, or mounting. Should specific problems occur that are not addressed by these
instructions, contact your local sales representative or distributor for assistance. Retain these instructions for future reference.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE OR INJURY TO PERSONS:
Lighted fixture is hot. To reduce risk of injury to persons, turn fixture off or unplug and allow to cool before handling.
© 2012 Illumitex Inc. All rights reserved. The information in this document is subject to change without prior notice.
Illumitex Inc. | 5307 Industrial Oaks Blvd., Ste. 100 | Austin, TX 78735 USA | +1 512 279 5020 | www.illumitex.com