Index
Handing Chart
Details
Architectural Accessories Detail
WoodDoor
DoorTechnical
TechnicalManual
Manual
Wood
GRAHAM | MAIMAN
Contents
Construction Detail................................................................................................................................................... 2
Wood Moulding..................................................................................................................................................... 3-4
Louver Unites - Wood and Metal ......................................................................................................................... 5
Vision Panels - Wood and Metal........................................................................................................................... 6
Factory Installed Glass.......................................................................................................................................... 7-9
Astragals/Edges.........................................................................................................................................................10
Dutch Door......................................................................................................................................................... 11-16
Door with Transoms......................................................................................................................................... 17-20
Wicket Door..............................................................................................................................................................21
Special machining - Rabbiets/Radius Edge......................................................................................................22
Fire Door Plant-Ons.................................................................................................................................................23
Full Glass / Full Warranty Door.............................................................................................................................24
ElectroLynx.................................................................................................................................................................25
Door Glazing Charts......................................................................................................................................... 26-27
2
Construction Details
Architectural Accessories Details
Wood Door Technical Manual
GRAHAM | MAIMAN
Meeting Edge Options
No Bevel
Bevel
Rabbeted
Parallel Bevel
Dbl. Egress
Metal Edge
Guards/Astragal
Metal Edge
Guards
Flat Astragal
Glazing Options
Standard Minimums
All cutouts for metal or wood vision panels must be a
minimum of 5” (152 mm) from the edge of the door
and/or other cutouts for louvers, locks, closers or other
hardware.
Flush Mouldings*
This 5” (152 mm) distance must be maintained or the
fire label and warranty will be voided. For non-fire rated
doors, the distance may be decreased to 5” (127 mm).
Less than 5” (127 mm) may affect the warranty
Using a 10” (254 mm) margin between the edge of the
door and the edge of any cutout near the lock area will
eliminate most label and warranty conflicts.
Lip Mouldings**
* A variance in the downset of flush mouldings may occur due to allowable tolerance deviations of components.
** Lip mouldings only are available for Thermal Fused Doors.
3
Wood Mouldings
Architectural Accessories Details
Wood Door Technical Manual
GRAHAM | MAIMAN
General Moulding Requirements
Species shall match or be compatible with face veneer or laminate
Moulding shall be free of open defects, shake, splits, or doze
Moulding must be smooth and free of visible knife, saw or sanding marks
Lip Moulding for Lites
3
2
1. Matching specie to door face veneer for Premium grade. For use with
1-3/4” thick doors
M2G - Flat Lip Moulding 15/16” wide x 5/8” thick, 3/32” radius.
M3G - Beveled Lip Moulding 15/16” wide x 3/8” thick, 3/32” radius
2. Wire Brad - Lip Moulding is factory attached.
3. 1/4” Glazing - Glazing materials are not included.
4. Beveled back for glazing compound or 1/16” tape (not included).
5. Lites - Order size - visible glass size
Cutout size = visible glass + (2 x moulding profile)
Glass size = cutout - 1/4” wide - 1/4” high
1
15/16”
4
15/16”
3/32”
3/32”
3/8”
3/8”
5/8”
11/16”
5/8”
11/16”
M2G
M3G
Flush Moulding for Lites
3
2
1
1. Matching specie to door face veneer for Premium grade. For use with
1-3/4” thick doors
M6G - Flush Moulding 11/16” wide x 3/8” thick, 3/32” radius.
2. Wire Brad - Flush Moulding is factory attached.
3. 1/4” Glazing - Glazing materials are not included.
4. Beveled back for glazing compound or 1/16” tape (not included).
5. Lites - Order size - visible glass size
Cutout size = visible glass + (2 x moulding profile)
Glass size = cutout - 1/4” wide - 1/4” high
3/32”
4
3/8”
A variance in the downset of flush mouldings may occur due to allowable tolerance deviations of components.
11/16”
M6G
4
Wood Mouldings
GRAHAM | MAIMAN
Architectural Accessories Details
Wood Door Technical Manual
Fire Rated Flush Wood Moulding for Lites
1. Available with 45, 60 and 90 minute fire rated (mineral core) doors.
2. Factory installed: glass, glazing material, glazing bead, clips, nails,
provided.
3. Flush Moulding Profile: MF3
4. Available Species: Red Oak, Natural Birch, White Maple, Cherry,
Mahogany, and Walnut. Contact you Customer Service Professional for
availability of other species.
5. Glass: 1/4” thick nominal wired glass or 3/16” thick nominal ceramic
6. Cutout Size and Glass Size: (100 in2 maximum)
Cutout Width = Visible Glass Width + 1.500”
Cutout Height = Visible Glass Height + 1.500”
Glass Width = Visible Glass Width + 1.375”
Glass Height = Visible Glass Height + 1.375”
3/4”
MF3
A variance in the downset of flush mouldings may occur due to allowable tolerance deviations of components.
5
Louver Units
Architectural Accessories Details
Wood Door Technical Manual
GRAHAM | MAIMAN
V-Slat Wood Louver
11/16”
1
3/32”
5/8”
7/16”
M2W
1/2”
3
3/32”
3/8”
3/4”
2
7/16”
M6 W
1. L100 Wood Non-Vision Louver Unit - 3/4” wide, 33% free
air movement. Matching specie to door face veneer for
Premium grade. For use with 1-3/4” thick doors. Specify
louver size the same as cutout size. 1-3/8” thick doors
require framed louvers. Louvers may not be installed in
20 minute fire doors.
M2W - Flat Lip Moulding 11/16” wide x 5/8” thick, 3/32” radius.
M6W - Flush Moulding 7/16” wide x 3/8” thick, 3/32” radius
2. Wire Brad - Mouldings are factory attached. Louvers are
not factory installed as standard. Louvers may be facorty
installed as an option.
3. Field installation may require the use of glazing tape for
proper fit.
A variance in the downset of flush mouldings may occur due to allowable tolerance deviations of components.
V-Slat Metal Louver
9/16”
3/32”
1
5/8”
5/16”
M2M
1/2”
3/32”
3
3/8”
1/16”
2
5/16”
M6M
1. L600 Metal Non-Vision Louver Unit - 1-1/16” wide, 20
gauge steel, 50% free air movement. For use with 1-3/4”
thick doors. 1-3/8” thick doors require framed louvers.
Louver cutout is 1/8” less then order size. Louvers may not
be installed in 20 minute fire doors.
M2M - Flat Lip Moulding 9/16” wide x 5/8” thick, 3/32” radius.
M6M - Flush Moulding 5/16” wide x 3/8” thick, 3/32” radius
2. Wire Brad - Mouldings are factory attached. Louvers are
not factory installed. Louvers may be facorty installed as an
option.
3. Field installation may require the use of glazing tape for
proper fit.
A variance in the downset of flush mouldings may occur due to allowable tolerance deviations of components.
Metal Fusible Link Louver
3
1
2
1. L1900A Framed Metal Non-Vision Louver Unit - Fire
rated fusible link unit for use with 45, 60 or 90 minute
fire doors. 1-3/4” wide. 135 degree F fusible link. 40% free
air movement. For use with 1-3/4” thick doors only. Not
factory installed. Louvers may not be installed in 20
minute fire doors.
2. Stell mounting frame overlaps door face 1”.
3. Through bolt applied. Security screws are available by
option.
4. Metal fusible link louvers will not be factory installed.
6
Vision Panels
Architectural Accessories Details
Wood Door Technical Manual
GRAHAM | MAIMAN
Fire rated Metal Vision Panel
1. M110 Metal Vision Frame - Fire rated for 20, 45, 60 and 90 minute
fire door applications. 18 gauge steel with mitered, round corners
that are braced and welded. Available wood veneer wrapped as an
option. Low profile for hardware clearance.
2. Metal frame and glazing support clip.
3. Vandal proof binder screw.
4. For 1/4” thick listed glazing (not included).
Note: No glazing compound or tape is required. Not factory installed.
5. Fire rated metal vision panels will be factory installed.
6. Lites - Order size = visible glass size
Cutout size = visible glass size + 1-1/2” side + 1-1/2” high
Glass size = visible glass size + 3/4” wide + 3/4” high
7. Listed for UL10b and UL10c.
4
3
1
2
Note: Custom shapes for specialty lites must be specified for visible glass size and cutout size.
20 Minute Moulding for Lites
1. Matching specie to door face veneer for Premium grade. For use with
1-3/4” thick 20 minute rated fire doors.
M2L - Beveled Lip Moulding 1” wide x 3/4” thick.
M2F - Beveled Flush Moulding 3/4” wide x 1/2” thick.
2. Metal glazing support clip.
3. Glazing compound or tape required for proper fit (not included).
4. For 1/4” thick listed glazing (not included).
Size are visible glass size. Cutouts are 1” larger in width and height.
Custom shapes for specialty lites must be specified for visible glass size and cutout size.
5. Lites - Order size = visible glass size
Cutout size = visible glass size + (2 x moulding profile)
Glass size = cutout - 1/4” wide - 1/4” high
6. Listed for UL10b and UL10c.
4
1
3
2
A variance in the downset of flush mouldings may occur due to allowable tolerance deviations of components.
Note: Custom shapes for specialty lites must be specified for visible glass size and cutout size.
4
11/16”
1/2”
1/2”
1/2”
9/32”
1”
M2F
M2L
1
3
2
7
Factory Installed Glass
Architectural Accessories Detail
Wood Door Technical Manual
GRAHAM | MAIMAN
KERALITE® FILMED GLASS DESCRIPTION
FIRE RATING 20-90 MINUTE
US TESTING LISTED AND LABELED WITH UNDERWRITERS LABORATORIES INC. FILE #R14515.
TESTED IN ACCORDANCE WITH UL 9, UL 10B, UL 10C, NFPA 80, NFPA 252, NFPA 257
CANADIAN TESTING CAN/ULC-S106, S104
IMPACT SAFETY RATING CPSC 16CFR PART 1201 (CATEGORIES I & II), ANSI Z97.1, CAN/CGSB-12.1-M
NOMINAL THICKNESS 3/16” (5 MM)
THICKNESS TOLERANCE +1/64” TO -1/64” (+0.4 MM TO -0.4 MM)
U VALUE BTU/(HR*SQFT*DEGF) 0.88
WEIGHT (LBS/SQ FT.) 2.4
APPROX. VISIBLE LIGHT TRANSMISSION 86%
RATING
MAXIMUM
EXPOSED AREA
MAXIMUM
WIDTH
MAXIMUM
HEIGHT
CORE TYPE
20, 45
1296
36
54
Mineral, Particleboard, Stave Lumber,
Engineered Composite, Agrifiber
20, 45
2550
34
75
Mineral, Particleboard, Stave Lumber,
Engineered Composite
60*
900
12
75
Mineral
60*
864
24
36
Mineral
60, 90
1296
24
54
Mineral
Temp Rise
100
12
33
Mineral
** Glazing tape required for all fire rated applications
KERALITE® LAMINATED
GLASS DESCRIPTION
FIRE RATING 20-90 MINUTE
US TESTING LISTED AND LABELED WITH UNDERWRITERS LABORATORIES INC. FILE #R14515
TESTED IN ACCORDANCE WITH UL 9, UL 10B, UL 10C, NFPA 80, NFPA 252, NFPA 257
CANADIAN TESTING CAN/ULC-S106, S104
IMPACT SAFETY RATING CPSC 16CFR PART 1201 (CATEGORIES I & II). ANSI Z97.1, CAN/CGSB-12.1-M
NOMINAL THICKNESS 5/16” (8 MM)
THICKNESS TOLERANCE +1/64” TO -1/64” (+0.4 MM TO -0.4 MM)
U VALUE BTU/(HR*SQFT*DEGF) 0.88
WEIGHT (LBS/SQ FT.) 4.1
APPROX. VISIBLE LIGHT TRANSMISSION 82%
RATING
MAXIMUM
EXPOSED AREA
MAXIMUM
WIDTH
MAXIMUM
HEIGHT
CORE TYPE
20, 45
1296
36
54
Mineral, Particleboard, Stave Lumber,
Engineered Composite, Agrifiber
20, 45
2550
34
75
Mineral, Particleboard, Stave Lumber,
Engineered Composite
60*
900
12
75
Mineral
60*
864
24
36
Mineral
60, 90
1296
24
54
Mineral
Temp Rise
100
12
33
Mineral
** Glazing tape required for all fire rated applications
8
Factory Installed Glass
GRAHAM | MAIMAN
Architectural Accessories Details
Wood Door Technical Manual
FIRELITE® NT (FIG05)
Glass Description
CERAMIC, FILMED FIRE AND SAFETY RATED GLASS
BRAND: FIRELITE NT
GRADE: PREMIUM
THICKNESS: 3/16” NOMINAL
WARRANTY: 3 YEAR LIMITED
INCLUDES: GLAZING TAPE AND SETTING BLOCKS AS REQUIRED
IMPACT SAFETY RATING: CPSC 16CFR1201, CAT I AND CAT II
FIRE LISTINGS
UL APPROVED, POSITIVE
PRESSURE. GLASS IS
MARKED IN
ACCORDANCE WITH
INTERNATIONAL
BUILDING CODE
SECTION 715.4.6 AND
2406
RATING
MAXIMUM
EXPOSED AREA
MAXIMUM
WIDTH
MAXIMUM
HEIGHT
CORE TYPE
20, 45
1296
36
54
Mineral, Particleboard, Stave Lumber,
Engineered Composite, Agrifiber
1
20, 45
2856
34
84
Mineral, Particleboard, Stave Lumber,
Engineered Composite
2
60*
960
12
80
Mineral
NOTES
2
60*
864
24
36
Mineral
2
60, 90
1296
24
54
Mineral
Temp Rise
100
12
33
Mineral
* 2 lites max
1 Same as above PEMKO FG3000845
2 Same as above PEMKO FG3000890
FIRELITE® PLUS (FIG06)
Glass Description
CERAMIC, LAMINATED FIRE AND SAFETY RATED GLASS
BRAND: FIRELITE PLUS
GRADE: PREMIUM
THICKNESS: 5/16” NOMINAL
WARRANTY: 5 YEAR LIMITED
INCLUDES: GLAZING TAPE AND SETTING BLOCKS AS REQUIRED
IMPACT SAFETY RATING: CPSC 16CFR1201, CAT I AND CAT II
FIRE LISTINGS
UL APPROVED, POSITIVE
PRESSURE. GLASS IS
MARKED IN
ACCORDANCE WITH
INTERNATIONAL
BUILDING CODE
SECTION 715.4.6 AND
2406
RATING
MAXIMUM
EXPOSED AREA
MAXIMUM
WIDTH
MAXIMUM
HEIGHT
CORE TYPE
20, 45
1296
36
54
Mineral, Particleboard, Stave Lumber,
Engineered Composite, Agrifiber
1
20, 45
2856
34
84
Mineral, Particleboard, Stave Lumber,
Engineered Composite
2
60*
960
12
80
Mineral
2
60*
864
24
36
Mineral
2
60, 90
1296
24
54
Mineral
Temp Rise
100
12
33
Mineral
NOTES
* 2 lites max
1 Same as above PEMKO FG3000845
2 Same as above PEMKO FG3000890
9
Factory Installed Glass
Architectural Accessories Detail
Wood Door Technical Manual
GRAHAM | MAIMAN
1/4” TEMPERED (FIG01)
Glass Description
1/4” CLEAR TEMPERED IMPACT SAFETY RATED GLASS
QUALITY RATING: Q3, ASTM C1036-06
THICKNESS: 1/4” NOMINAL
WARRANTY: 1 YEAR LIMITED
INCLUDES: GLAZING TAPE AND SETTING BLOCKS AS REQUIRED
IMPACT SAFETY RATING: CPSC 16CFR1201, CAT I AND CAT II
GLASS IS MARKED IN ACCORDANCE WITH INTERNATIONAL BUILDING CODE SECTION 2406
NOT FOR USE ON FIRE RATED DOORS
1/4” FILMED WIRE (FIG02)
Glass Description
1/4” FILM WIRE, FIRE AND IMPACT SAFETY RATED GLASS
QUALITY RATING: Q3, ASTM C1036-06
THICKNESS: 1/4” NOMINAL
WARRANTY: 1 YEAR LIMITED
INCLUDES: GLAZING TAPE AND SETTING BLOCKS AS REQUIRED
IMPACT SAFETY RATING: CPSC 16CFR1201, CAT I AND CAT II
FIRE LISTINGS
UL AND
INTERTEK/WARNOCKHERSEY APPROVED,
POSITIVE PRESSURE.
GLASS IS MARKED IN
ACCORDANCE WITH
INTERNATIONAL
BUILDING CODE
SECTION 715.4.6 AND
2406
RATING
MAXIMUM
EXPOSED AREA
MAXIMUM
WIDTH
MAXIMUM
HEIGHT
CORE TYPE
20, 45
1296
36
54
Mineral, Particleboard, Stave Lumber,
Engineered Composite, Agrifiber
60, 90 *
300
15
33
Mineral
100
12
33
Mineral
Temp Rise
* Non Temp Rise
10
Astragals/Edges
GRAHAM | MAIMAN
Architectural Accessories Details
Wood Door Technical Manual
Flat Wood Astragal
1. A1 Wood Astragal - 2” wide, 1/2” thick, 1/4” radius on face edges.
Matching specie to door face veneer for Premium grade. For use with
1-3/4” or 1-3/8” thick doors.
2. May be applied using wood screws and adhesive.
3. Not for use on any 45, 60 or 90 minute fire rated doors. Flat wood
astragals may be applied to 20 minute neutral pressure tested pairs
with Firestop metting edges.
1
Metal Astragal & Edge
1. M207. metal Edge Set With Overlapping Astragal - 16 gauge welded
astragal overlaps meeting edge 1”. Approved for 20, 45, 60 and 90
minute fire door applications. Available wood veneer wrapped as
an option. May be specified unmachined or machined for builders
hardware.
2. 20 gauge wrap-around metal edge overpals meeting stile 1”.
3. Phillips Flat head Screws - #8 x 3/4” 12” on center (included).
3
Note: Overlapping astragals are no longer required for fire rated pairs.
1
2
Double Metal Edge
1. M208 Double Metal Edge Set - 20 gauge wrap-around metal edge
overlaps metting stiles of doors 1”. Approved for 20, 45, 60 and 90
minute fire door applications. Available wood veneer wrapped as
an option. may be specified unmachined or machined for builders
hardware.
2. Phillips Flat head Screws - #8 x 3/4”, 12” on center (included).
Note: Double metal edges are no longer required on 20, 45, 60 or 90
minute paris if doors are specified to be without metal edges. Requires
special interior blocking profiles.
3. Also available with 5” wrap-around metal edges for use with the
application of concealed vertical rod exit devices in the M250 series.
2
1
11
Dutch Door (Non Fire Rated)
Architectural Accessories Detail
Wood Door Technical Manual
GRAHAM | MAIMAN
General Notes
Allow for shelf thickness when specifying hardware.
Standard shelf is 1.125” (28 mm) thick wood, 1 side only.
Standard wood shelf sits between leaves.
Shelf and supports are not factory installed
Note if shelf is not required.
Note if other than standard shelf is required.
Dutch doors are available in GPD or GCD bonded consturction
only.
8. GPD has matching bottom rail in top leaf. GCD has non-matching
bottom rail in top leaf.
9. Dutch doors are available in single openings up to 4’0” x 9’0”.
Dutch doors are available in paired openings up to 8’0” x 9’0”.
Height By Specification
1.
2.
3.
4.
5.
6.
7.
1-3/4”
(includes shelf)
Height By Specification
1/8”
8”
Shelf
4”
1-1/8”
4”
Shelf Bracket
12
Dutch Door (Non Fire Rated)
GRAHAM | MAIMAN
Architectural Accessories Details
Wood Door Technical Manual
NON RATED DUTCH DOOR
General Notes
1. Dutch doors may be provided with:
a. Straight cut metting edges of top and bottom leaf.
b. Rabbeted metting edges of top and bottom leaf.
2. Standard clearnace between top leaf and bottom
leaf of Dutch doors is 3/16”.
3. Dutch door latching may be cylindrical, mortise
or flushbolt latches that latch:
a. top leaf into bottom leaf, bottom leaf into frame.
b. top leaf into bottom leaf, top leaf into frame.
c. top leaf into frame, bottom leaf into frame.
TOP LEAF
2” Wood Rails (Min.)
1-1/8” Wood Shelf
2” Wood Rails (Min.)
BOTTOM LEAF
EXAMPLE OF LATCHING CONFIGURATION
TOP LEAF
TOP LEAF
BOTTOM LEAF
BOTTOM LEAF
ACTIVE LEAF
INACTIVE LEAF
PAIR OF DUTCH DOORS
13
Dutch Door (20 Minute Fire Rating)
Architectural Accessories Detail
Wood Door Technical Manual
GRAHAM | MAIMAN
General Notes
Height By Specification
1.
2.
3.
4.
5.
6.
7.
8.
(includes shelf)
Height By Specification
1/8”
Allow for shelf thickness when specifying hardware.
Standard shelf is 1.125” (28 mm) thick wood, 1 side only.
Standard wood shelf sits between leaves.
Shelf and supports are not factory installed
Note if shelf is not required.
Note if other than standard shelf is required.
Dutch doors are available in GPD or GCD bonded consturction only.
GPD has Firestop bottom rail in top leaf. Firestop top rail in bottom
leaf. GCD has Firestop bottom rail in top leaf, Firestop top rail in
bottom leaf.
9. Dutch doors are not available in 90 minute neutral pressure tested
construction.
10. Positive pressure fire tested Dutch door constructions are not
available.
11. Dutch doors are available in 20 minute fire rated single openings up
to 4’0” x 8’0”.
12. Dutch doors are available in 20 minute fire rated paired openings up
to 8’0” x 8’0”.
1-3/4”
8”
Shelf
1-1/8”
4”
4”
Shelf Bracket
14
Dutch Door (20 Minute Fire Rating)
GRAHAM | MAIMAN
Architectural Accessories Details
Wood Door Technical Manual
General Notes
20 MINUTE DUTCH DOOR
1. 20 minute Dutch doors may be provided with one of
these:
a. An overlapping astragal applied to the bottom rail of the top leaf
b. Intumescent fire seal installed in the bottom rail of the top leaf.
c. Standard wood shelf sits between leaves.
2. A maximum 1/8” (3.2 mm) clearance between top leaf
and bottom leaf of fire rated Dutch doors is allowed.
3. Fire rated Dutch doors require both leaves to be self
latching. Leaf to leaf or leaf to frame.
4. Fire rated Dutch door latching is limited to cylindrical
or mortise latches that latch:
a. top leaf into bottom leaf, bottom leaf into frame.
b. top leaf into bottom leaf, top leaf into frame.
c. top leaf into frame, bottom leaf into frame.
5. Flushbolts are allowed on the inactive leaves of a pair.
TOP LEAF
2” wide Firestop Rails (Min.)
Intumescent
1-1/8” Wood Shelf
2” wide Firestop Rails (Min.)
BOTTOM LEAF
EXAMPLE OF LATCHING CONFIGURATION
TOP LEAF
TOP LEAF
BOTTOM LEAF
BOTTOM LEAF
ACTIVE LEAF
INACTIVE LEAF
PAIR OF DUTCH DOORS
15
Dutch Door (45/60 Minute Fire Rated)
Architectural Accessories Detail
Wood Door Technical Manual
GRAHAM | MAIMAN
General Notes
Height By Specification
1.
2.
3.
4.
5.
6.
7.
8.
(includes shelf)
Height By Specification
1/8”
Allow for shelf thickness when specifying hardware.
Standard shelf is 1.125” (28 mm) thick wood, 1 side only.
Standard wood shelf butts to face of bottom leaf.
Shelf and supports are not factory installed
Note if shelf is not required.
Note if other than standard shelf is required.
Dutch doors are available in GPD or GCD bonded consturction only.
GPD has Firestop bottom rail in top leaf. Firestop top rail in bottom
leaf. GCD has Firestop bottom rail in top leaf, Firestop top rail in
bottom leaf.
9. Dutch doors are not available in 90 minute neutral pressure tested
construction.
10. Positive pressure fire tested Dutch door constructions are not
available.
11. Dutch doors are available in 45/60 minute fire rated single openings
up to 4’0” x 8’0”.
12. Dutch doors are not available in 45/60 minute fire rated paired
openings.
1-3/4”
8”
Shelf
1-1/8”
4”
4”
Shelf Bracket
16
Dutch Door (45/60 Minute Fire Rated)
GRAHAM | MAIMAN
Architectural Accessories Details
Wood Door Technical Manual
General Notes
45/60 MINUTE DUTCH DOOR
1. 45/60 minute Dutch doors may be provided with one of
these:
a. An overlapping astragal applied to the bottom rail of the top leaf
b. Intumescent fire seal installed in the bottom rail of the top leaf.
c. Standard wood shelf sits between leaves.
2. A maximum 1/8” (3.2 mm) clearance between top leaf and
bottom leaf of fire rated Dutch doors is allowed.
3. Fire rated Dutch doors require both leaves to be self
latching. Leaf to leaf or leaf to frame.
4. Fire rated Dutch door latching is limited to cylindrical or
mortise latches that latch:
a. top leaf into bottom leaf, bottom leaf into frame.
b. top leaf into bottom leaf, top leaf into frame.
c. top leaf into frame, bottom leaf into frame.
EXAMPLE OF LATCHING CONFIGURATION
TOP LEAF
TOP LEAF
BOTTOM LEAF
BOTTOM LEAF
TOP LEAF
2” wide Firestop Rails (Min.)
Intumescent
1-1/8” Wood Shelf
2” wide Firestop Rails (Min.)
BOTTOM LEAF
17
Door with Transom (20 Minute Fire Rated)
Architectural Accessories Detail
Wood Door Technical Manual
GRAHAM | MAIMAN
20 Minute Fire Rated Doors with Transoms
1. Transom panels must be the same construction as the 20 minute fire door.
2. Neutral pressure tested doors with transom panels may be rabbeted, or installed with a metal edge and astragal, or
with a transom bar between the door and transom.
Positive pressure tested doors with transom panels must be installed in a frame with a transom bar between the door and transom.
3. Transom installed over a pair of 20 minute rated doors must be separated with a frame mullion. The mullion must limit
the width of each separate transom to the width of each leaf of the door pair.
4. The transom panel must be machined for spring bolts by the licensed machiner of manufacturer. The appropriate
number of springbolts will be supplied by the machiner.
5. Fire rating labels will be provided on door and transom stating “Door and Transom Assembly.”
6. Fire rated transom panels must be installed using approved steel springbolts. The springbolts shall be placed 2” (51
mm) from each corner with the minimum number centered on each side. Holes must be drilled in the frame to accept
the springbolts. Hole locations vary with respect to rabbeted and unrabbeted tansoms.
Panels up to 18” (458 mm) in height require 2 springbolts per side.
Panels up to 36” (916 mm) in height require 3 springbolts per side.
Panels up to 40” (1220 mm) in height require 4 springbolts per side.
7. Maximum clearance between the frame and panel must be 1/8” (3.2 mm).
8. Doors with transoms are available in single openings up to 4’0” x 10”0”. Maximum transom panel size in a single
opening up to 4’0” wide x 3’4” high. Doors with transoms are available in paired openings up to 8’0” x 10’0”. Maximum
transom panel size is a paired opening is 8’0” wide x 3’4” high. Transom panels above pairs of doors must be separated
by a mullion.
18
Door with Transom (20 Minute Fire Rated)
GRAHAM | MAIMAN
Architectural Accessories Details
Wood Door Technical Manual
Solid Wood Cores
Transom
1” Wide Firestop Rails Min.
1/8” Max. Gap
1/8” Max. Gap
1” Wide Firestop Rails Min.
Steel Astragals
Solid Wood Cores
1-3/4”
20 Minute Doors with Transoms
1.
Neutral pressure tested fire doors with transoms may be
provided with:
a. Straight cut meeting edges of door and transom with an over lapping astragal.
b. Straight cut metting edges of door and transom with frame transom bar.
c. Rabbeted meeting edges of door and transom.
Positive pressure tesed fire doors with transoms must be installed in a frame with
transom bar between the door and transom.
2. A maximum 1/8” (3.2 mm) clearance between door
and transom is allowed in non-rabbeted applications.
Maximum clearance between the frame and transom
panel must be 1/8” (3.2 mm).
3. Fire rated Transom panels must be installed using
approved steel springbolts. The springbolts shall be
placed 2” (51 mm) from each corner with the minimum
number centered on each side. Holes must be drilled in
the frame to accept the springbolts. Hole locations vary
with respect to rabbeted and unrabbeted transoms.
Panels up to 18” (458 mm) in height require 2 springbolts per side.
Panels up to 36” (916 mm) in height require 3 springbolts per side.
Panels up to 40” (1220 mm) in height require 4 springbolts per side.
1-3/4”
20 MINUTE DOOR WITH TRANSOM
IN FRAME WITH MULLION
Transom
1” Wide Firestop
Rails Min.
Mullion
1” Wide Firestop
Rails Min.
19
45/60/90 Minute Fire Rated Doors with Transoms
Architectural Accessories Detail
Wood Door Technical Manual
GRAHAM | MAIMAN
45/60/90 Minute Fire Rated Doors with Transoms
1. Transom panels must be the same construction as the 20 minute fire door.
2. Neutral pressure tested doors with transom panels may be rabbeted, or installed with a metal edge and astragal, or
with a transom bar between the door and transom. Rabbeted door and transom assemblies must be constructed with
minimum 5” (127 mm) Firestop bottom rail of transom and top rail of door. The rabbet must be a minimum 1/2” (13
mm) deep x 7/8” (22 mm) wide.
Positive pressure tested doors with transom panels must be installed in a frame with a transom bar between the door and transom.
3. If an overhead door closer is to be installed the bottom rail of the transom and the top rail of the door must be 5” (127
mm) Firestop. When transom bar is provided the rails shall be standard Firestop or Firestop II material.
4. Transom installed over a pair of fire rated doors must be separated with a frame mullion. The mullion must limit the
width of each separate transom to the width of each leaf of the door pair.
5. The transom panel must be machined for spring bolts by the licensed machiner of manufacturer. The appropriate
number of springbolts will be supplied by the machiner.
6. Fire rating labels will be provided on door and transom stating “Door and Transom Assembly.”
7. Fire rated transom panels must be installed using approved steel springbolts. The springbolts shall be placed
2” (51 mm) from each corner with the minimum number centered on each side. Holes must be drilled in the frame to
accept the springbolts.
Panels up to 18” (458 mm) in height require 2 springbolts per side.
Panels up to 36” (916 mm) in height require 3 springbolts per side.
Panels up to 40” (1220 mm) in height require 4 springbolts per side.
Maximum clearance between the frame and panel must be 1/8” (3.2 mm).
8. Neutral pressure tested fire doors with transoms are available in single openings up to 4’0” x 10”0”.
Positive pressure tested fire doors with transoms are available in single openings up to 4’0” x 9”0”.
Neutral pressure tested fire doors with transoms are available in paired openings up to 8’0” x 10”0”.
Positive pressure tested fire doors with transoms are available in paired openings up to 8’0” x 9”0”.
Maximum transom panel size in a single opening up to 4’0” wide x 3’4” high.
Maximum transom panel size in a paired opening is 4’0” wide x 3’4” high.
Transom panels above pairs of doors must be separated by a mullion.
20
Doors with Tramsoms (45/60/90 Minute Fire Rated)
GRAHAM | MAIMAN
Architectural Accessories Details
Wood Door Technical Manual
Transom
5” Wide Firestop Rails Min.
1/8” Max. Gap
1/8” Max. Gap
5” Wide Firestop Rails Min.
Steel Astragals
1-3/4”
45/60/90 Minute Doors
with Transoms
1.
Neutral pressure tested fire doors with transoms may be
provided with:
a. Straight cut meeting edges of door and transom with an over lapping astragal.
b. Straight cut metting edges of door and transom with frame transom bar.
c. Rabbeted meeting edges of door and transom. Rabbeted meeting edges require 5” (127 mm)
bottom rail of tramson and top rail of door.
Positive pressure tesed fire doors with transoms must be installed in a frame with transom bar
between the door and transom.
2. A maximum 1/8” (3.2 mm) clearance between door
and transom is allowed in non-rabbeted applications.
Maximum clearance between the frame and transom
panel must be 1/8” (3.2 mm).
3. Fire rated Transom panels must be installed using
approved steel springbolts. The springbolts shall be
placed 2” (51 mm) from each corner with the minimum
number centered on each side. Holes must be drilled in
the frame to accept the springbolts. Hole locations vary
with respect to rabbeted and unrabbeted transoms.
Panels up to 18” (458 mm) in height require 2 springbolts per side.
Panels up to 36” (916 mm) in height require 3 springbolts per side.
Panels up to 40” (1220 mm) in height require 4 springbolts per side.
1-3/4”
45/60/90 MINUTE DOOR WITH TRANSOM
IN FRAME WITH MULLION
Transom
G-P Firestop Composition
1” Wide Firestop
Rails Min.
Mullion
G-P Firestop Composition
1” Wide Firestop
Rails Min.
21
Wicket Doors (Standard)
Architectural Accessories Detail
Wood Door Technical Manual
GRAHAM | MAIMAN
General Notes
1.
2.
3.
4.
5.
Requires handing of call door and wicket door
Latch/lock for call door must be suitable for rabbeted application
Shelf and call door are not factory installed
Available in GPD or GCD bonded constructions only
SCLC (EC) core required
Hinged Side
Unrabbeted
Call
Door
Rabbeted
3/32”
Reveal
Shelf
1-1/8” Thick Shelf
Wicket
Door
1-3/4”
8”
13/16”
2”
Call Door Size
9/16”
Shelf
Opening Size
4”
4”
1-3/4”
Typical Rabbet
Shelf Bracket
22
Special Machining
GRAHAM | MAIMAN
Architectural Accessories Details
Wood Door Technical Manual
General Notes
Standard Rabbet
1. Provide non-vision joint between door and transom.
2. Non-fire rated wood core door/transom units hae solid matching
hardwood top rail in door and bottom rail in transom.
3. Rabbets allow 1/8” spacing between door and transom when door is in
closed position.
4. Available on 20-minute rated doors/transoms.
5. May be applied to 45, 60 and 90-minute fire doors. Mineral core
fire door/transom units do not have matching rails. requires special
construction.
6. Available on 1-3/4” thick doors only.
7. Available in GPD or GCD bonded constructions only.
Note: GPD has matching bottom rail on top leaf and matching top rail on bottom leaf.
GCD has non-matching bottom rail on top leaf and non-matching top rail on bottom leaf.
General Notes
1. Used on doors when specified using pivot hinges or when double
acting door is specified.
2. When specified for application to lock stile, verify lock/latch hardware
compatibility. Requires full face stile.
3. When specified for application to hinge stile, verify radius of edge with
hardware template requirements.
4. Available on 1-3/4” thick doors only.
5. Available in GPD or GCD bonded constructions only.
6. Not available on any fire rated door.
7. Specify radius on hinge and lock edge.
Transom
Door
Radius Edge
Available Radii (R)
Convex
Concave
2-1/2”
1-7/8”
1-1/2”
1-5/32”
1-5/32”
23
Fire Door Plant-Ons
Architectural Accessories Detail
Wood Door Technical Manual
GRAHAM | MAIMAN
General Notes
Minimum spacing
to edge of door or
cutout.
Minimum spacing
between plant-ons.
Decorative Door Plant-ons are allowed on 20, 45, 60 and 90 minute
labeled fire doors. The following conditions apply:
1. Type, size and configuration are limited by the door
manufacturer’s tested authorities.
2. The plant-ons must be applied under label service at factory or
qulaified distributor. Plant-ons may not be field applied to fire
rated doors.
Standard Profiles Offered
1. ASSA ABLOY Wood Doors offers the following profiles.
Customers may supply assembled plant-ons in other species and
profiles, provided they meet the specifications for the intended
use listed below. These may also be used on non-fire rated doors.
9/16”
Minimum enclosed
area.
3/4”
1-1/2”
1-1/2”
P-7
P-8
Twice the profile
width for width of
area..
5/8”
2-3/8”
P-9
Specifications
20 Minute
GP 45/60 Minute
GP 90 Minute
Max. Profile Width:
1-3/4”
2-1/2”
2-1/2”
Max. Profile Height
3/4”
3/4”
3/4”
Wood Specie
Douglas Fir or Denser
Same
Same
Attachment
Adhesive or Mechanical
Adhesive or mechanical
Adhesive
4”
4”
4”
Equal or Greater than Profile
Same
Same
N/A
2 Time Profile Width & Height
2 Time Profile Width & Height
Mouldings may not cover in
excess of 20% of door face.
Mouldings may not cover in
excess of 22% of door face.
Mouldings may not cover in
excess of 22% of door face.
Spacing: to edge
of door or cutout
Between Plant-ons
Min. Enclosed Area
Coverage
24
Full Glass/Full Warranty Door
GRAHAM | MAIMAN
Maximum Size:
Thickness:
Stiles:
Series:
Core:
Faces:
Coutout Size:
Mouldings:
Glazing Material:
Warranty:
Architectural Accessories Details
Wood Door Technical Manual
4’0” wide x 9’0” high
1-3/4” only
Laminated hardwood construction or veneer banded.
Available as an option only in the GPD EC and GCD EC product lines.
PC, EC (SCLC)
Two ply veneered plywood, 1/8” thick, with face veneer thickness of 1/50” minimum at 12% moisture
content.
Mimimum stile width is 5” from edge of door to cutout.
Minimum rail width is 5” from edge of door to cutout.
Maximum lite cutout is 40% of surface area.
These dimensions actual, taken from the prefit size of the door If 20 minute fire rating is required a
maximum 1296 square inches of vision area is allowed.
M2G (lip), M3G (beveled lip), and M6G (flush) MVP profiles are available. All mouldings are sized for
installation with 1/4” safety tempered or wired. Moulding or lite kits are not factory attached. For
non-fire rated doors, wood mouldings must be installed using 3/32” glazing tape on both sides of the
glass and must be fastened every 8” on center using 3rd finish nails (Glazing tape and finish nails are not
provided). For fire rated applications follow the installation intructions for the listed and labeled lite
kit specified. With listed and labeled wood or metal kits may be specified.
For non-fire rated applications 1/4” tempered safety glazing must be used. 1/4” wired glazing may be
specified if desired. (Glazing is not included). For fire rated applications listed and labeled glazing
materials may be specified.
When finished and installed per manufacturers specifications this product carries a full lifetime
warranty against manufacturer defect on interior applications. The product is not warranted for
exterior application in any event. Exterior applications are those which expose a door to extremes
of temperature and/or humidity regardless of the physical placement.
25
ElectroLynx™ System
Architectural Accessories Detail
Wood Door Technical Manual
GRAHAM | MAIMAN
THE GRAHAM ELECTROLYNX CABLE IS EQUIPPED WITH THE ELECTROLYNX SYSTEM OF PLUG IN
CONNECTORS FOR FAST, EASY, CONNECTION TO SIMILARLY EQUIPPED ASSAABLOY HARDWARE.
THE ELECTROLYNX CABLE HAS 12 CONDUCTORS OF 22 GA. WIFRE, WITH ELECTROLYNX CONNECTORS.
POWER OVER ETHERNET (POE) IS AVAILABLE IF REQUIRED.
CL
5 HINGE DOOR
3/8”
MULTIPLE
CABLE
4 HINGE DOOR
SINGLE
CABLE
SINGLE
CABLE
3 HINGE DOOR
VERIFY CABLE LOCATION
BEFORE MODIFYING DOOR
OR SURFACE APPLICATION OF
HARDWARE.
HINGE EDGE
LOCK EDGE
AVAILABLE IN GPD & GCD DOORS ONLY
ELECTRIC
HINGE
LOCATION
HARDWARE
LOCATION
*ELECTRIC
HINGE
LOCATION
ELECTRIC
HINGE
LOCATION
LOCK EDGE
MULTIPLE
CABLE*
HINGE EDGE
ELECTRIC
HINGE
LOCATION
ELECTRIFIED
TRIM
3/8”
*DOOR MUST BE
PREPPED WITH A
MINIMUM OF
4 HINGES
ELECTRIC
HINGE
LOCATION
FIRE STOP BLOCKING
OR WIDER FIRE STOP
STILE DEPENDING ON
HARDWARE REQUIREMENTS
*THE ELECTROLYNX HINGE WILL ALWAYS
BE LOCATED IN THE SECOND HINGE
FROM THE FLOOR
MAXIMUM OF TWO RACEWAYS PER DOOR ON FIRE-RATED DOORS.
CAN BE USED IN BOTH NEUTRAL & POSITIVE PRESSURE DOORS CATEGORY A & B
26
Door Glazing Chart
GRAHAM | MAIMAN
Architectural Accessories Details
Wood Door Technical Manual
General Notes:
• All glass must be fire rated and safety impact rated.
• To meet label requirements there must be 3-5/16” between all hardware and lite cutouts in door.
Lite Kit
Max
Size
Max
Width
Max
Length
110
Wood
110
110
110
110
110
1296
1296
1296
300
100
300
100
36
36
36
15
12
15
12
54
54
54
33
33
33
33
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
No
No
No
No
Yes
No
Yes
110
1296
36
54
3/16"
No
20 Minute
110
2856*
34
84
3/16"
No
Maximum 4090 door. Must use Pemko FG3000S45
Glazing Tape. Not allowed on AF core doors.
45 Minute
110
1296
36
54
3/16"
No
AF core only
45 Minute
110
2856*
34
84
3/16"
No
60 Minute
60 Minute
110
110
300
100
15
12
33
33
3/16"
3/16"
No
Yes
Maximum 4090 door. Must use Pemko FG3000S45
Glazing Tape. Mineral core only.
60 Minute
110
1296*
24
54
3/16"
No
60 Minute
110
960*
12
80
3/16"
No
90 Minute
90 Minute
110
110
300
100
15
12
33
33
3/16"
3/16"
No
Yes
90 Minute
110
1296*
24
54
3/16"
No
Firelite Plus
20 Minute
110
1296
36
54
5/16"
No
20 Minute
110
2856*
34
84
5/16"
No
45 Minute
110
1296
36
54
5/16"
No
45 Minute
110
2856*
34
84
5/16"
No
60 Minute
60 Minute
110
110
300
100
15
12
33
33
5/16"
5/16"
No
Yes
60 Minute
110
1296*
24
54
5/16"
No
60 Minute
110
960*
12
80
5/16"
No
90 Minute
90 Minute
110
110
300
100
15
12
33
33
5/16"
5/16"
No
Yes
90 Minute
110
1296*
24
54
5/16"
No
Fire Rating
Filmed Wire
20 Minute
20 Minute
45 Minute
60 Minute
60 Minute
90 Minute
90 Minute
Firelite NT
20 Minute
* Multiple Lites Allowed
AF Core = Agrifiber core
Glass Thick- Temp
ness
Rise
Notes
AF and Mineral core
Maximum 4090 door. Must use Pemko FG3000S90
Glazing Tape.
Maximum 4090 door. Must use Pemko FG3000S90
Glazing Tape. (Two lite maximum. 960 sq in. each.
12" maximum width)
Maximum 4090 door. Must use Pemko FG3000S90
Glazing Tape.
Maximum 4090 door. Must use Pemko FG3000S45
Glazing Tape. Not allowed on AF core doors.
AF and mineral core only
Maximum 4090 door. Must use Pemko FG3000S45
Glazing Tape. Mineral core only.
Maximum 4090 door. Must use Pemko FG3000S90
Glazing Tape.
Maximum 4090 door. Must use Pemko FG3000S90
Glazing Tape. (Two lite maximum. 960 sq in. each.
12" maximum width)
Maximum 4090 door. Must use Pemko FG3000S90
Glazing Tape.
27
Door Glazing Chart
Architectural Accessories Detail
Wood Door Technical Manual
GRAHAM | MAIMAN
General Notes:
• All glass must be fire rated and safety impact rated.
• To meet label requirements there must be 3-5/16” between all hardware and lite cutouts in door.
Max
Size
Max
Width
Max
Length
Pyran Platinum F
20 Minute
110
1296
36
54
3/16"
No
20 Minute
110
2550*
34
75
3/16"
No
45 Minute
110
1296
36
54
3/16"
No
45 Minute
110
2550*
34
75
3/16"
No
60 Minute
60 Minute
110
110
300
100
15
12
33
33
3/16"
3/16"
No
Yes
60 Minute
110
1296*
24
54
3/16"
No
60 Minute
110
900*
12
75
3/16"
No
90 Minute
90 Minute
110
110
300
100
15
12
33
33
3/16"
3/16"
No
Yes
90 Minute
110
1296*
24
54
3/16"
No
Pyran Platinum L
20 Minute
110
1296
36
54
3/8"
No
20 Minute
110
2550*
34
75
3/8"
No
45 Minute
110
1296
36
54
3/8"
No
45 Minute
110
2550*
34
75
3/8"
No
60 Minute
60 Minute
110
110
300
100
15
12
33
33
3/8"
3/8"
No
Yes
60 Minute
110
1296*
24
54
3/8"
No
60 Minute
110
900*
12
75
3/8"
No
90 Minute
110
300
15
33
3/8"
No
90 Minute
110
100
12
33
3/8"
Yes
90 Minute
110
1296*
24
54
3/8"
No
Fire Rating
Lite Kit
* Multiple Lites Allowed
AF Core = Agrifiber core
Glass Thick- Temp
ness
Rise
Notes
Maximum 4090 door. Must use Pemko FG3000S45
Glazing Tape. Not allowed on AF core doors.
AF and mineral core only
Maximum 4090 door. Must use Pemko FG3000S45
Glazing Tape. Mineral core only.
Maximum 4090 door. Must use Pemko FG3000S90
Glazing Tape.
Maximum 4090 door. Must use Pemko FG3000S90
Glazing Tape. (Two lite maximum. 900 sq in. each.
12" maximum width)
Maximum 4090 door. Must use Pemko FG3000S90
Glazing Tape.
Maximum 4090 door. Must use Pemko FG3000S45
Glazing Tape. Not allowed on AF core doors.
AF and mineral core only
Maximum 4090 door. Must use Pemko FG3000S45
Glazing Tape. Mineral core doors only.
Maximum 4090 door. Must use Pemko FG3000S90
Glazing Tape.
Maximum 4090 door. Must use Pemko FG3000S90
Glazing Tape. (Two lite maximum. 900 sq in. each.
12" maximum width)
Maximum 4090 door. Must use Pemko FG3000S90
Glazing Tape.