Dimensions & Outline:
XL Mover
The Moving Image Technologies XL Mover platform
supports the XL 3D projection system from Real-D.
The system mounts to the front of the pedestal
supporting the projector. Alternatively it may
be mounted to the front booth wall below the
projection port. It utilizes polished shafts with
linear bearings so the movable element slides
back and forth easily. A gearmotor positions the
XL system in front of the lens or to the side,
controlled remotely. Manual pushbuttons are
provided for manual override.
Regulatory:
All elements of the system are low-voltage, except for an in-line, recognized DC power
supply. Regulatory approval is not being sought for the system.
Part Numbers:
A000360-001 Standard XL Mover System, 30.5” OAL, 12” carriage travel
A000360-002 Extended XL Mover System, 42” OAL, 24” carriage travel
A000360-101 XL Mover system with reversed 2D/3D ends function (for CDS). Includes mounting brackets.
Features:
• The unit moves the XL unit from one extreme to the other in under 10 seconds.
Special Component Part Options:
System mounting bracket. Adapts the XL Mover mounting holes to 19” rack mounting pattern
(2 ea required):
• The system includes a ‘soft-stop’ feature at both ends of travel. C001413-001 2.5” long (standard)
C001413-002 4.25” long (extended) C001413-003 8.25” long (extra long, support legs to floor recommended)
• Includes a timeout feature so it won’t continue to drive if an object is blocking the path.
XL carriage top, bracket with slots for mounting XL core:
• LEDs indicate when the unit has reached either end of travel.
C001422-002 11” L x 5.5” H (Standard)
C001422-003 8” L x 4.5” H (Compact)
C001422-004 9” L x 1” H (Flat) C001458-001 Mounting Adapter bracket, allows sliding the XL Mover left or right up to 5”
from center
• Quiet operation, typically can’t be heard over the projector and server fans.
Control:
The control of the system is by low-voltage contact closures. These can be from an automation system,
or from a projector with macro-driven GPDI outputs. The same macros that select 2D and 3D modes
on the projector may also be programmed to activate GPDI outputs driving the XL unit in or out of the
optical path. A terminal block is provided for making connections.
A small control panel is provided on the operator side of the unit with manual pushbuttons to select the
desired position of the unit, overriding the last command received from the GPDI inputs.
Mechanical:
Dimensions:
28.0 x 17.75 x ~12” deep
Weight:
TBD
* Due to on-going development, features and specifications
subject to change without notice.
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
2
3
XLS Mover
The Moving Image Technologies XLS Mover
platform supports the XLS 3D projection
system from Real-D for Sony projectors.
The system mounts to the front of the lens
iMAGE LIFT
The Moving Image Lift mounts to the rear wall
of an auditorium. It consists of a quiet projector
enclosure ‘pod’ riding on a vertical track. The
system raises the projector into position where
it will have a clear sightline to the screen
utilizing a light weight design. Bearing
for projection, and lowers it to a convenient
cams on an aluminum tracks allow a
height for service. The product facilitates a
gearmotor to positions the XLS system in
“boothless” cinema design.
front of the lens or to the side. System is
controlled through remote automation or
manually by override push buttons.
Features:
• Automatic safety interlock
• Key switch to raise and lower the unit included
• Various projection heights may be selected at
Features:
• The unit moves the XLS unit from one extreme to the other in under 5 seconds.
• Quiet operation, typically can’t be heard over the projector and server fans.
• Includes a timeout feature so it won’t continue to drive if an object is blocking the path.
• LEDs indicate when the unit has reached either end of travel
Control:
The control of the system is by low-voltage contact closures. These can be from an automation
system, or from a projector with macro-driven GPDI outputs. The same macros that select 2D and
3D modes on theprojector may also be programmed to activate GPDI outputs driving the XLS unit
in or out of the optical path. A terminal block is provided for making connections.
A small control panel is provided on the operator side of the unit with manual pushbuttons to
select thedesired position of the unit, overriding the last command received from the GPDI
inputs.
installation.
• All parts made from rugged formed and welded
steel
• Projector enclosure has removable side panels
for service
• 24” sq. projection port included as standard with water-clear, A/R coated glass
• Interface plate at the top of the system facilitates electrical and HVAC connections
• Includes 8RU of standard 19” rack mounting under the projector.
Site Requirements:
The system requires a load-bearing wall at the rear of the auditorium. Alternatively the wall must be
reinforced with additional steel or heavy gage studs (details available on request).
Power Requirements:
The system requires a dedicated 120VAC, 15A circuit for the hoist (in addition to the power required
for the projector).
Part Number:
A000410-001 Lift System, 12’-0” track height, 141” max. enclosure ht.
A000410-002 Lift System, 13’-6” track height, 159” max. enclosure ht.
* Due to on-going development, features and specifications
subject to change without notice.
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
4
5
MICROPOD
HUSH RACK
The MOVING iMAGE TECHNOLOGIES Hush Rack is designed for
all your video and audio rack mounting needs. The Hush Rack
provides a level of security uncommon in typical equipment
racks. A solid, welded design is ideal for mounting equipment
behind the screen where audio pressure would rattle a
typical sound rack. High volume, low-pressure ventilation
is filtered to keep your amps breathing cleanly with minimal
service required in the dirtiest of environments. Coupled
with the MOVING iMAGE TECHNOLOGIES IS Series of power
“The newest addition to Moving iMage
Technologies suite of products to
support boothless theater designs is the
“Micropod”. Simple yet attractive in
appearance, it fits into any décor to share
the auditorium with the audience. The
Micropod is designed specifically for the
NC900 & NC1100 projectors (or equivalent
small footprint projectors).
protection. The MOVING iMAGE TECHNOLOGIES hush rack
The design uses a rugged 10GA steel frame
combined with lightweight aluminum
covers for the optimum combination of
ruggedness and light weight. The Micropod
is intended to be suspended from a ceiling
is the latest product in our line to support alternative
or overhead structure, 3/4” female threaded sockets are provided at the four corners of the frame for
auditorium configurations including boothless cinema.
attaching hooks, cables, or other suspension fittings. It’s also compatible with MiT’s Lift system, so it may
filtering and remote switching products, the MOVING iMAGE
TECHNOLOGIES Hush Rack can be remotely powered up/down
to support efficient energy management and equipment
be lowered to a convenient height for servicing the projector (see separate specifications for lift).
Features:
Features:
• 40 RU of secure rack space
• Welded steel powder-coated construction
• 5 point lockable steel security doors
• Air filters in front and back doors
• High-volume, low pressure fans for quiet ventilation.
• Cable lacing channels for ease of cable dressing & management
• Bonded grounding post
• Sealed enclosure for quiet operation
• 8” Supply and Exhaust fittings on the top facilitate HVAC connections
• 9” square water white A/R coated glass port, gasketing, and trim included as standard
• Optional sound damping foam composite panels may be factory-installed for an even
lower noise profile
Mechanical:
• Dimensions:
• Weight: 42.0 x 34.5 x 21” high
130lbs (measured)(not including foam)
• Bare rack rails for secure grounding of devices
• Adjustable rack rails front and rear for flexible mounting
• Support channel at the bottom of rack for heavy amps or UPS
• Work light for ease of service
• Laser cut conduit knock-outs for flexibility of service entry/exit
• Available integration with all of MiT power filtering, distribution products
• Rack integration services available to deliver a fully wired and tested product to your specifications.
Important note: As the installation of this unit is outside the control of MiT, we disclaim all
liability for damage to equipment or personal injury resulting from improper installation. Using
lifting-rated hardware is essential! MiT recommends always consulting a structural engineer for
any installation of equipment over an audience.
* Due to on-going development, features and specifications
subject to change without notice.
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
6
7
S1 Pedestal
Block Diagram:
The MOVING iMAGE TECHNOLOGIES S-1 Digital Cinema Pedestal is a base intended to support D-Cinema
projectors and related equipment securely and with ease of alignment and service. The S-1 accommodates
DLP projectors from all manufacturers and is sturdy enough to support stackable projectors. The base
offers 14RU (24.5”) of standard 19” rack space and can be prewired with an optional PDU for simplified
power distribution. The top of the unit incorporates a tilting platform that can be adjusted to provide up
to a 10-degree down angle. The S-1 can accommodate all D-Cinema Servers as well as the full line of MiT
accessories. This includes IMC automations, M-Series Dimmers and IS-30 Spike Arrestors all of which can
be pre wired in our factory to your custom specifications. (See separate specifications for details)
Accessories & Options
Projectors Supported:
• NEC - NC1600, NC2500, NC1200, NC2000, NC3200.
• Barco - DP90, DP3000, DP1200, DP1500, DP2000, DP2K-12C, DP2K-15C, DP2K-20C,
• Christie - CP2000M, CP2000-ZX, CP2220, CP2210, CP2000-XB, CP2230.
Features:
• Large Projector Adapter Plate
• PDU Power Distribution Unit
• IMC-2 or IMC-3j Automation
• S-1 Riser and Cart for 60” high port windows
• Docking Pin Kit for S-1 Riser and Cart
• IS-30 Spike/Surge Arrestor
• M-Series Dimmer
• Integration and Prewire
• Hold down clamps (seismic)
Mechanical:
• Dimensions
• Weight
34.0 x 22.0 x 29.1 in. high [864 x 559 x 739mm]
200lbs [90 kg]
• Rugged all-welded welded steel construction, durable powder coat finish.
• Tilt table allows 10-degrees down angle with safety latches.
• Conduit knockouts on the front side for routing power and signals.
• Feet-capturing devices to lock the projector to the base, and the base to the floor.
• 14U of Standard 19” rack space. 24.5” deep.
• Integration and prewire available to your custom requirements.
8
* Due to on-going development, features and specifications
subject to change without notice.
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
9
Block Diagram:
S2 Pedestal
The MOVING iMAGE TECHNOLOGIES S2 Pedestal is the most widely used pedestal in D Cinema today. It has
been designed by MiT engineers for ergonomics and functionality, while at the same time being attractive to
the eye. It consists of a rugged, welded enclosure made from 14 Ga steel. It’s designed to support projectors
up to 400 lbs. Customers have the choice of louvered panels or screened doors for the unused rack mounting
areas. The S2 can accommodate all D-Cinema Servers as well as the full line of MiT accessories. This
includes IMC automations, M-Series Dimmers and IS-30 Spike Arrestors all of which can be pre wired in our
factory to your custom specifications. (See separate specifications for details)
Options:
• Power Distribution Unit
• International Voltages Available
• IMC Series Automation Systems
• Is-30 Spike/Surge Protection Unit
• M-Series Dimmer
• Pre Assembly And Wiring
• Pre Configuration And Addressing Of
Network
• Seismic Foot Clamps
Part Numbers:
Features:
• Supports small and large DLP projectors from
all major OEMs
• 14 U rack space available from 3 sides for
flexible configuration
• Internal work light built-in to ease service
• May be track mounted
• Tilt block available for greater tilt
• Hold-down clamps secure projector feet
• For use in new construction or retrofits
• A000310-001
• A000176-00x
• A000282-00x
• A000290-00x
• C003184-001
• C003199-001
• PA00001-00x
Standard Pedestal
Power Distribution unit (N. America and International versions)
IMC-3j Automation system, 2RU tray
IS-30 Spike and surge arrestor (120/220V and 230/380V versions)
Tilt Riser Block
Adapter, NEC projector mount (2 req’d)
Dimmer (2 channel and 4 channel versions)
Mechanical:
• Dimensions:
• Weight: 42.0 x 30.5 x 31” high
200lbs
• Long leveling feet allow tilting to 10 degrees
• Conduit knockouts on the front side for routing
power in and out
* Due to on-going development, features and specifications
subject to change without notice.
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
10
11
S3 Pedestal (30 inch)
Block Diagram:
The MOVING iMAGE TECHNOLOGIES S3 Pedestal was made with special consideration for consolidation of
the all D Cinema components. It has been designed by MiT engineers for functionality and optimization,
without sacrafice. It consists of our standard rugged, welded enclosure made from 14 Ga steel & is designed
to support projectors up to 400 lbs. Customers have the choice of louvered panels or screened doors for the
unused rack mounting areas. The S3 can accommodate all D-Cinema Servers as well as audio components
with enough rack space for a full line of MiT accessories. This includes IMC automations, M-Series Dimmers
and IS-30 Spike Arrestors all of which can be delivered integrated from the MiT factory. (See separate
specifications for details)
Options:
• Power Distribution Unit
• International Voltages Available
• IMC Series Automation Systems
• IS-30 Spike/Surge Protection Unit
• M-Series Dimmer
• Pre Assembly and Wiring
• Pre-Configuration and Addressing of
Network
• Seismic Foot Clamps
Part Numbers:
Features:
• Supports small and large DLP projectors
from all major OEMs
• Tilt block available for greater tilt
• 28 RU of space available from 3 sides
for flexible configuration to accomodate
more equipment
• For use in new construction or retrofits
• Internal work light built-in to ease
service
• Long leveling feet allow tilting to 10
degrees
• Hold-down clamps capture projector feet
• Conduit knockouts on the front side for
routing power in and out
• A000332-001
• A000176-00x
• A000282-00x
• A000290-00x
• C003184-001
• C003199-001
• PA00001-00x
Standard Pedestal
Power Distribution unit (N. America and International versions)
IMC-3j Automation system, 2RU tray
IS-30 Spike and surge arrestor (120/220V and 230/380V versions)
Tilt Riser Block
Adapter, NEC projector mount (2 req’d)
Dimmer (2 channel and 4 channel versions)
Mechanical:
• Dimensions:
• Weight: 54.0 x 30.5 x 30” high
200lbs
• May be track mounted
* Due to on-going development, features and specifications
subject to change without notice.
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
12
13
S3 Low Profile Pedestal
Block Diagram:
The MOVING iMAGE TECHNOLOGIES S3 is a Low Profile Pedestal designed for screens with unique space
limitations and low port windows. It has been designed by MiT engineers to accomodate crucial D CInema
equipment, with the same eye appeal as the taller S Series Bases. It consists of a rugged, welded enclosure
made from 14 Ga steel. It’s designed to support projectors up to 400 lbs. Customers have the choice of
louvered panels or screened doors for the unused rack mounting areas. The S3 can accommodate all
D-Cinema Servers as well as a select number of MiT accessories, depending on placement and configuration.
This includes IMC automations, IS-30 Spike Arrestors all of which can be pre wired in our factory to your
custom specifications. (See separate specifications for details)
Options:
• Power Distribution Unit
• International Voltages Available
• IMC Series Automation Systems
• Is-30 Spike/Surge Protection Unit
• M-Series Dimmer
• Pre Assembly and Wiring
• Pre-Configuration and Addressing of
Network
• Seismic Foot Clamps
Part Numbers:
• A000310-001
• A000176-00x
• A000282-00x
• A000290-00x
• C003184-001
• C003199-001
• PA00001-00x
Features:
• Supports small and large DLP projectors
from all major OEMs
• Tilt block available for greater tilt
• 16 RU of space available from 2 sides
for flexible configuration to accomodate
crucial equipment.
• For use in new construction or retrofits
• Internal work light built-in to ease
service
• Long leveling feet allow tilting to 10
degrees
• Hold-down clamps capture projector feet
• Conduit knockouts on the front side for
routing power in and out
Standard Pedestal
Power Distribution unit (N. America and International versions)
IMC-3j Automation system, 2RU tray
IS-30 Spike and surge arrestor (120/220V and 230/380V versions)
Tilt Riser Block
Adapter, NEC projector mount (2 req’d)
Dimmer (2 channel and 4 channel versions)
Mechanical:
• Dimensions:
• Weight: 42.0 x 30.5 x 13” high
200lbs
• May be track mounted
* Due to on-going development, features and specifications
subject to change without notice.
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
14
15
Dual Projector Stacking System
Block Diagram:
The MOVING iMAGE TECHNOLOGIES Dual Projector Stacking System provides a robust support frame to
add a second projector above our Series 3 low-profile pedestal. It includes an exhaust adapter duct for
the lower projector to facilitate HVAC hookup. The stacker frame is fabricated from rugged 10 GA steel
and designed to support projectors up to 400 lb. The Dual Projector Stacking System allows on center
targeting for ease of convergence in your Premium Large Format auditorium. The system can accommodate
various optional components such as the XL-Mover (2), IMC automation, IS-30 Spike Arrestor, IS-20 Power
Managers, or other products, all of which can be pre wired in our factory to your custom specifications.
(See separate specifications for the S3 Low Profile Pedestal).
Options:
• Power Distribution Unit
• International Voltages Available
• IMC Series Automation Systems
• IS-30 Spike/Surge Protection Unit
• M-Series Dimmer
• Pre Assembly and Wiring
• Pre-Configuration and Addressing of
Network
• Seismic Foot Clamps
Part Numbers:
• A000310-001
• A000176-00x
• A000282-00x
• A000290-00x
• C003184-001
• C003199-001
• PA00001-00x
Features:
• Supports small and large DLP projectors
from all major OEMs
• Tilt blocks available for greater tilt
• 16 RU of space available from 2 sides
for flexible configuration to accomodate
crucial equipment.
• For use in new construction or retrofits
• Internal work light built-in to ease
service
• Long leveling feet allow tilting to 10
degrees
• Hold-down clamps capture projector feet
• Conduit knockouts on the front side for
routing power in and out
• May be track mounted
Standard Pedestal
Power Distribution unit (N. America and International versions)
IMC-3j Automation system, 2RU tray
IS-30 Spike and surge arrestor (120/220V and 230/380V versions)
Tilt Riser Block
Adapter, NEC projector mount (2 req’d)
Dimmer (2 channel and 4 channel versions)
Mechanical:
• Dimensions:
• Weight: 53.0 x 35.5 x 50” high
80lbs (280lbs mounted to S3 Low Profile Base)
* Due to on-going development, features and specifications
subject to change without notice.
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
16
17
S4 Pedestal (DE)
Block Diagram:
The MOVING iMAGE TECHNOLOGIES S4 Pedestal was made with special consideration for consolidation of
the all D Cinema components. It has been designed by MiT engineers for functionality and optimization,
without sacrafice. It consists of our standard rugged, welded enclosure made from 14 Ga steel & is designed
to support projectors up to 400 lbs. Customers have the choice of louvered panels or screened doors for the
unused rack mounting areas. The S4 can accommodate all D-Cinema Servers as well as audio components
with enough rack space for a full line of MiT accessories. This includes IMC automations, M-Series Dimmers
and IS-30 Spike Arrestors all of which can be delivered integrated from the MiT factory. (See separate
specifications for details)
Options:
• Power Distribution Unit
• International Voltages Available
• IMC Series Automation Systems
• IS-30 Spike/Surge Protection Unit
• M-Series Dimmer
• Pre Assembly and Wiring
• Pre-Configuration and Addressing of
Network
• Seismic Foot Clamps
Part Numbers:
Features:
• Supports small and large DLP projectors
from all major OEMs
• Tilt block available for greater tilt
• 21 RU of space available from 2 sides
for flexible configuration to accomodate
more equipment
• For use in new construction or retrofits
• Internal work light built-in to ease
service
• Long leveling feet allow tilting to 10
degrees
• Hold-down clamps capture projector feet
• Conduit knockouts on the front side for
routing power in and out
• A000332-001
• A000176-00x
• A000282-00x
• A000290-00x
• C003184-001
• C003199-001
• PA00001-00x
Standard Pedestal
Power Distribution unit (N. America and International versions)
IMC-3j Automation system, 2RU tray
IS-30 Spike and surge arrestor (120/220V and 230/380V versions)
Tilt Riser Block
Adapter, NEC projector mount (2 req’d)
Dimmer (2 channel and 4 channel versions)
Mechanical:
• Dimensions:
• Weight: 42.50 x 27.25 x 43” high
200lbs
• May be mounted on track or casters
* Due to on-going development, features and specifications
subject to change without notice.
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
18
19
Dimensions & Outline:
IMC-2 (IMC-2e) Automation Controller
The MOVING iMAGE TECHNOLOGIES IMC-2 platform is a multipurpose interface device for use in the
cinema. It can provide digital communication capability to film-based systems, assist in integrating
onscreen advertising or pre-feature entertainment systems, and provides various interface functions in
the implementation of D-Cinema. In conjunction with a D-Cinema server, it can serve as a complete
automation for a typical D-Cinema system.
In a typical installation, the IMC-2 receives cue commands from a server via RS-232 (or ethernet interface
for the IMC2e) and controls the projector and all auditorium functions.
The unit comes standard with a lacing bar to facilitate and support the wiring at the rear. Also the rack
mounting ears may be removed if the unit is desired to mount elsewhere, for example to a wall.
• 12 digital inputs (7 cue or event
inputs, plus 5 dedicated inputs for
Flat, Scope, Dimmer Up, Dimmer
Down, and Emergency Stop
• Customizable program for each
intended application
• 16 relay-driven outputs, each with
indicator LED
• Durable powder coat finish
• 1 ethernet port and 1 serial COM port
(IMC-2e)
12VDC @ 500 mA (a wall mounted power supply is included with the unit)
Part Numbers: Accessories & Options:
A000202-001
A000202-003
PA00016-012
Features:
• 2 Serial COM ports (IMC-2)
Electrical Requirements:
• Gangable to increase I/O capability
Assy, IMC-2 Controller
Assy, IMC-2e Controller
Power Supply, 12V, wall mount
Mechanical:
Dimensions:
Weight:
19.0 x 8.75 x 1.7 in. [483 x 222 x 44mm]
6lbs [2.7 kg]
• Conduit knockouts top and bottom
• 1U rack-mountable or wall-mountable
• Pluggable terminal blocks for all
connections
* Due to on-going development, features and specifications
subject to change without notice.
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
20
21
Dimensions & Outline:
IMC-3j Automation
The MOVING iMAGE TECHNOLOGIES IMC-3j platform is a standalone automation system for digital cinema
applications. It interfaces with the latest generation of digital projectors, servers, audio processors, and
also supports pre-feature entertainment systems.
In a typical installation the IMC-3j receives cue commands from a d-cinema server and controls the
projector and audio processor via the Local Area Network (Ethernet) port. Digital inputs and outputs
interface with legacy equipment as well as curtains, masking, lighting, and other auditorium functions.
Electrical Requirements:
Features:
• 8 digital (GPIO) inputs
• 8 relay-driven outputs
• 5 outputs rated for 1Amp, 30V
• Masking outputs rated for 5
Amps, 120V
• Preshow projector output rated
for 10 Amps, 120V
12VDC @ 500 mA (a wall mounted power supply is included with the unit)
• Fire Alarm input is configurable for
common fire panel voltages and control
methods
• Customizable programs for most
applications
• Manual controls on the front panel for
masking, dimmer, preshow, and fire alarm
clear
• 2 Serial COM ports
• Expansion modules available to increase
I/O capability
• Ethernet Support
• Open-frame design provides easy access
• Terminal blocks for all connections
• Includes remote termination board
Part Numbers: Accessories & Options:
A000282-004
PA00016-012
Assy, IMC-3j Controller
Power Supply, 12V, wall mount
Mechanical:
Dimensions:
Weight:
19.0 x 14.5 x 3.5 in. [483 x 368 x 86mm]
10lbs [4.5 kg]
* Due to on-going development, features and specifications
subject to change without notice.
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
22
23
Dimensions & Outline:
IMC-4j Automation
The MOVING iMAGE TECHNOLOGIES IMC-4j platform is a standalone automation system for digital cinema
applications. It interfaces with the latest generation of digital projectors, servers, audio processors, and
also supports pre-feature entertainment systems.
In a typical installation the IMC-4j receives cue commands from a d-cinema server and controls the
projector and audio processor via the Local Area Network (Ethernet) port. Digital inputs and outputs
interface with legacy equipment as well as curtains, masking, lighting, and other auditorium functions.
Features:
• 8 digital (GPIO) inputs
• 2 Serial COM ports
• 8 relay-driven outputs
• Ethernet Support
• 5 outputs rated for 1Amp, 30V
• Terminal blocks for all connections
• Masking outputs rated for 5 Amps,
120V
• Fire Alarm input is configurable for common
fire panel voltages and control methods
• Preshow projector output rated for
10 Amps, 120V
• Customizable programs for most applications
• Inputs: PreShow Start (with buttons on the
front panel for Start and End), PreShow
End, Curtain/Light show control and
Projector Macro Preload
• Outputs: Separate House and Stage Dimmer
(with control buttons on front panel) Low
Voltage Control, Curtain Open and Close
(with control buttons on front panel)
High Voltage Control, Door Magnet Open
and Close (High Voltage), Logic Output
(programmable) and End Of Day Lamp Kill
24
Electrical Requirements:
• Manual controls on the front panel for
masking, dimmer, preshow, and fire alarm
clear
• Expansion modules available to increase I/O
capability
12VDC @ 500 mA (a wall mounted power supply is included with the unit)
Part Numbers: Accessories & Options:
A000282-004
PA00016-012
Assy, IMC-3j Controller
Power Supply, 12V, wall mount
Mechanical:
Dimensions:
Weight:
19.0 x 14.5 x 3.5 in. [483 x 368 x 86mm]
10lbs [4.5 kg]
• Open-frame design provides easy access
• Includes remote termination board
* Due to on-going development, features and specifications
subject to change without notice.
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
25
Typical Sound Rack Power
Consumption at Idle (Watts)
Processor
Monitor
Amps (5 ea)
Total / Rack Watts at idle
Hours idle (12am - 11am)
kWh used / rack idle / day
kwh used / rack idle / year
Typical kwh cost
Total savings / year / screen
IS-20 & IS-20d Power Manager
100
32
540
672
11
7.4
2698.08
$0.15
$404.71
The MOVING IMAGE TECHNOLOGIES IS-20 Series Power Manager offer AC distribution, sequential on/off
control, and surge suppression standard on all models. It has been designed specifically for racks with
multiple pieces of equipment that are desired to be powered on and off on a daily basis. It is ideal for
audio amplifier racks. It includes LEDs that indicate the status of all AC phases. The IS-20 accepts six 20Amp AC feeds, routes them through the switching elements, an EMI filter stage, and a surge protection
stage, then to receptacles on the rear panel.
On the standard IS-20 model, power up and power down sequences are controlled via Ethernet or low
voltage, dry contact closure.
The newly introduced IS-20d offers expanded digital functionality by giving discrete controls to each
circuit, programmable via a simple GUI (Graphical User Interface).
The IS-20 & IS-20d Power Manager should be the heart of your energy management plan. Powering systems
up and down just in time for their use saves on wasteful energy consumption during system idle time.
Features:
• Front Leds Indicate Power Status Of All
Circuits
• Current Rating Of 20 Amps Per Phase
Electrical Specifications:
• AC Requirements: 120VAC x 6 (20A breaker max.)
• Certified to: UL 1449, IEC 61643-1, EN 61643-11/21, Class 3 / Category A
• Surge suppression (on applicable models):
• Threshold voltage: 2kv
• Peak Surge current: 5000A
• Typical Life: 300 strikes (@500A surge)
Mechanical:
• Ethernet Or Dry Contact Control
• Individual Circuit Breakers
• For Use In New Construction Or Retrofits
• Pre-Programmed Power-Up And PowerDown Sequence.
• Terminal Block Connections
• Individual Circuit On/Off Control
• 2 U Rack Mountable
• Individual Circuit Power Filtering
• Regulatory-Approval (Pending)
Dimensions:
19.0 x 3.5 (2U) x 9” (preliminary)
Options
• 220 Volt Configuration
* Due to on-going development, features and specifications
subject to change without notice.
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
26
27
Block Diagram:
IS-30 AC Spike Arrestor
The MOVING iMAGE TECHNOLOGIES IS-30 is an AC power spike arrestor and filter-conditioner. It has been
designed by MiT’s engineers specifically to protect digital projectors and other cinema electronics in
the d-cinema age. It consists of a rugged, industrial-grade EMI/RFI filter, combined with spike and surge
protection components in a unique circuit arrangement that protects and absorbs spikes and surges lineto-ground as well as line-to-line. The unit includes a counter display to indicate how many power spikes
and surges have been absorbed and eliminated. It also includes LEDs that indicate the status of all AC
phases.
The unit has been designed to withstand and absorb severe spikes and surges, including those from nearby
lightning strikes. In the event of a direct, catastrophic lightning strike to the theatre, the IS-30 will take
the hit, sacrificing its components within and saving your delicate equipment. It incorporates a ‘bypass’
switch that restores the Power in an unfiltered state, to get the show back on-screen quickly. When the
unit is switched to the ‘Bypass’ mode a red LED illuminates as a reminder that spike protection is not in
effect.
Note: When used with smaller projectors utilizing 2-pole power, the third pole of the unit may be used to
protect other equipment in the auditorium, i.e. automations, servers, audio racks, etc.
Electrical Specifications:
• AC Requirements: 200-250VAC or 350-440VAC 3-phase, 35A per phase (50A breaker
max.)
• Certified to: UL 1449, IEC 61643-1, EN 61643-11/21, Class 3 / Category A
• Spike absorption Section:
• Threshold voltage: 2kv
• Peak Surge current: 5000A
• Typical Life: 300 strikes (@500A surge)
• EMI Filter Section:
• Insertion loss: 75dB typical line-to-line and line-to-ground (@1MHz)
Mechanical:
Features:
• Regulatory-approved (pending)
• 3-phase power protection, for either
small or large d-cinema projectors
Dimensions:
Weight:
• Bypass switch assures no service
interruption due to unit failure
• For use in new construction or retrofits
• LEDs on the front panel indicate power
status of all three phases
• Power connection by internal terminal
blocks
• Voltage ratings of 250VAC or 400VAC
phase-to-phase
• Conduit knockouts on the rear side for
routing power in and out
• Current rating of 35Amps per phase
• 2 U rack mountable
• Durable powder coat finish
28
19.0 x 3.47 (2U) x 10” (preliminary)
21lb (9.5kg)
Options
A000290-001
A000290-002
120/208V version
230/400V version
* Due to on-going development, features and specifications
subject to change without notice.
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
29
PDU (Power Distribution Unit)
Dimensions & Outline:
The MOVING iMAGE TECHNOLOGIES Power Distribution
Unit (PDU) is optional with the MiT Digital Cinema
Bases. It includes terminal blocks for terminating input
AC power and output loads, as well as circuit breakers
for the projector, server and other auditorium related
devices. The PDU’s flexibility allows a simple interface
for repurposing existing cinema wiring during retrofits
as well as a comprehensive distribution point for new
Digital Cinema installations. The unit is certified and
inspected to meet UL 60950.
Electrical Requirements:
• 208VAC or 380VAC, 60A service
Part Numbers & Options
A000176-001 North America, 2 pole. 30A service
A000176-002 North America, 3 pole. 60A service
A000176-201 International, 2 pole. 30A service
A000176-202 International, 3 pole. 60A service
Features:
• Circuit Breakers for:
• Projector
• Exhaust
• Masking
• Accessory
• Spare
• North America and International
Voltage versions available
• Approved to UL 60950 (bears ETL
label)
PE00035-015
Circuit Breaker, 1-pole, 15A
PE00035-020
Circuit Breaker, 1-pole, 20A
PE00364-015
Circuit Breaker, 2-pole, 15A
PE00364-020
Circuit Breaker, 2-pole, 20A
PE00364-030 Circuit Breaker, 2-pole, 30A vv
PE00037-030
Circuit Breaker, 3-pole, 30A
PE00037-035
Circuit Breaker, 3-pole, 35A
Mechanical:
Dimensions:
14.0”H x 9.0”W x 7.5”W
• Duplex receptacles on the rear of the
unit
* Due to on-going development, features and specifications
subject to change without notice.
• Dimmer
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
30
31
Internals
M-Series Lighting Dimmers
MOVING iMAGE TECHNOLOGIES M-Series lighting dimmers are designed specifically for commercial
cinemas with emphasis on reliability and value. Units come with front panel mounted manual override
and LED indicators for programming, status and level. The M-Series lighting dimmers are available in 2
and 4 channels supporting up to 9600 Watts of lighting power. The M-series lighting dimmer supports
incandescent, fluorescent* and LED lamps for the ultimate flexibility in your architectural lighting
selection. (*Dimmable ballasts required.)
Features:
• Tested to UL standards (US and Canada)
• Low-profile wall mount
• Model M4800 supports 2 channels at
2400 Watts each
• Model M9600 supports 4 channels at
2400 Watts each
• Independent ramp/fade rate for each
channel
• 3-position levels per channel with
precision settings
Options & Part Numbers
• Emergency bypass/panic feature, full-on
instantly
• Fuse protected solid-state control logic
• Full length heat sink for reliable heat
dissipation
• Simple, dry contact, interface to any
cinema automation
• Secondary Branch Circuit Breakers Available
• 200-240volt, 50/60Hz version for international applications
• M4800 2 channel standard.
PA00001-001 [120V] , -002 [220V]
• M9600 4 channel available.
• Supports low load, Fluorescent* and LED
lamps (*Dimmable ballast required)
• Toroidal transformer filtering
• 100-120V, 50/60Hz
* Due to on-going development, features and specifications
subject to change without notice.
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
32
33
Dimensions & Outline:
A-LMS 24
Architectural Lighting Management System
The MOVING iMAGE TECHNOLOGIES A-LMS platform is the latest addition to our suite of products to support
green initiatives, in this case for theater lighting applications. The A-LMS brings ‘smart’ capabilities to
auditorium lighting control based on the use of power-saving LED fixtures.
In a typical installation, the A-LMS receives scene cue commands from an automation or d-cinema server
via GPI contact closures, RS-232, or network interface.
The unit comes standard with a lacing bar at the rear to facilitate and support the control cabling. The
rack mounting ears may be removed if the unit is desired to mount to a wall.
Important note: There are different types of LED fixtures and ballasts available. Some are
dimmable to 10%, others are dimmable to 1%. For cinema use it’s essential that you procure LED
fixtures that are dimmable to 1%.
Electrical Requirements:
12VDC @ 1A (an inline power supply is included with
the unit)
Features:
• Designed for modern LED fixtures
that use the 1-10VDC architectural
dimming standard
• Scene cues selected by GPI contact
closures, serial commands, or LAN
commands
• Analog output drive capability: 60mA
per channel, typically drives up to 20
fixtures
• Emergency override “All on” and
“resume” functions
• Can also control incandescent lamps
with an optional external module
• Includes on/off relays for switching AC
power to fixtures: 250VAC, 15A max.
per channel
• Four scene presents
• Durable powder coat finish
• Two output channels standard, four
output channel option
• 1U rack-mountable or wall-mountable
• User programmable and status via
Ethernet with user-friendly web
interface
34
• Pluggable terminal blocks for all
connections
Part Numbers: Accessories & Options:
A000230-001
Assy, A-LMS 24 Unit, 2-channel
A000230-002
Assy, A-LMS 24 Unit, 4 channel
PA00016-112
Power Supply, 12V, inline (IEC),
Universal 100-230VAC input
Mechanical:
Dimensions: 19.0 x 11.75 x 1.7 in. [483 x 300 x 44mm]
Weight: 7lbs [3.1 kg
Screen Shot of A-LMS Interface
* Due to on-going development, features and specifications
subject to change without notice.
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
35
DCE-10/20 Exhaust Fan Controller
DCE-10/20 Installation Schematic
The DCE-10/20 is a closed loop controller for your projector exhaust. The DCE is designed to efficiently
control your projector exhaust, on demand, by managing your airflow and prevent the wasting of
conditioned air through your projector when cooling is not needed. This translates to an energy savings
by managing conditioned air demand of your projection booth. Depending on model, the DCE can
provide cfm, temperature and humidity data to your NOC to manage the operating conditions of your
projector.
• Boosts The Efficiency Of Your Projector Exhaust While Delivering The Demand Required.
• Eliminates Wasting Conditioned Air In Your Booth To Cool A Projector That Doesn’t Need It.
• Primary Exhaust Control is retained via the Projector or Automation.
• Supplementary Control Via Temperature Or Humidity (water) Sensors.
• Capable Of 2 Stage Operation (LOW-HIGH) When Used With A 2 Stage Fan.
• Interfaces with Fire Alarm System to Retain Proper Building Alarm Emergency Behavior.
• Passive Model for basic, 2 stage operation of the primary and booster exhaust.
• Advanced model for Ethernet connectivity and feedback to a house monitoring system or NOC.
• Passive and Advanced models will detect temperature and moisture.
• Advanced Model will support Ethernet connection and logging/trending of flow, temperature and
humidity.
• During down time the exhaust can be cycled to prevent cool down drafts from chilling your
electronics preventing potential condensation buildup inside the projector due to temperature
differential.
DCE-10
•
•
•
•
•
•
•
•
DCE-20
Passive Connectivity
Primary Fan Control
Booster Control
GPIO Interface
Temperature Sensing
Moisture Sensing
Fire Alarm Interface
Condensation Prevention Fan Cycling
•
•
•
•
•
•
DCE-10 Features Plus
Primary And Booster Control
2 Stage Booster Fan Control (High-Low)
CFM Measurement And Feedback
Temperature Feedback
Logging Of Flow, Temp And Moisture
• Dampers are sometimes used but are rarely insulated.
• In windy, heavy rain storms, protected roof vents can still be inundated by water.
-Emergency exhaust actuation can prevent some water from reaching the projector.
-At minimum, staff can be notified to detach the exhaust in a water compromised situation.
* Due to on-going development, features and specifications
subject to change without notice.
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
36
37
All-In-One Alternative Content Console
MOVING iMAGE SOURCE
Welcome to the World of Alternative Content
Features:
• 7 Channel Stereo Mixing Console
• Convenient A/V Patch Panel
• HDMI Input (digital audio & video)
• VGA Input
• Component Video Input
• Composite & S Video Input
In the world of Alternative Content, your solution is the MOVING iMAGE SOURCE, designed to support
• Analog Audio (x2)
a variety of alternative content for the Single Screen Cinema or Modern Multi-Screen complex.
• Video Switcher/Scaler included to properly
Completely mobile, this rugged, semi-scalable & multi-functional station incorporates everything under
format and switch A/V sources
the sun. It helps the exhibitor tap in to new markets and new revenue streams utilizing their Digital
• Blu-Ray Player
Cinema investment.
• Stereo Headphones
The MOVING iMAGE SOURCE is available in 3 standard configuration and can be customized with the
• Wired Mcrophone
features you require to accommodate all of your Alternative Content needs. Video Conferencing via
your broadband connection (Skype, Go2Meetings, Webcasts), Big Screen Gaming Competitions (Picture
in Picture) and anything you can imagine.
* Due to on-going development, features and specifications
subject to change without notice.
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
38
39
Lens Stabilizer
STB
STB Series Audio Termination Enclosure
Some users have found that in certain
The MOVING iMAGE TECHNOLOGIES STB Enclosures
are designed for terminating and interfacing audio
amplifiers to loudspeakers in a cinema. Large
gauge terminal blocks are provided for all channel
connections.
Reliable bare wire connections
provide secure contact without the use of crimp
connections. STB enclosures can be shipped ahead
to the job site to be incorporated into the audio
system conduit layout. In retrofit upgrades the
STB can be mounted in the narrow space between
existing conduits to provide convenient access to
your new B-Chain connections.
installations with unusually long or large
diameter lenses that the lens can vibrate,
causing a soft image on the screen. To address
this problem MiT has developed a bracket
that supports these types of lenses. The lens
stabilizer bracket mounts to the rear of the
MiT XL Mover and does not interfere with its
operation (XL Mover sold separately).
The lens is supported by non-marking nylon
transfer balls that allow the lens to continue
to rotate and move in and out for focusing
Features:
and
• Easily Identify All Of Your B-Chain
Connections
• Reliable, Bare-wire Terminal Blocks for
Secure Connections
• Supports Quad Amp, Stage Channels
• Convenient For Series And Paralleling
Surround Speakers
• All Connection Points Labeled With
Printed ID
• 2” And 1.5” EMT Knockouts On All Four
Sides
• Keyholes For Wall Mounting
bracket
telescopes
both vertical and lateral adjustment.
• Durable Powder-Coat Finish.
• For Use In New Construction Or Retrofits
The
vertically, and includes adjustment slots for
• Heavy, 16GA Steel Construction
• Tall, Narrow Footprint To Fit Between
Other Conduits
zooming.
Connections:
• Left, Center, Right: 4 Pairs Each
• Sub Channels: 8 Pairs
• Left, Right Surrounds: 12 Pairs Each
• Left, Right Back Surrounds: 6 Pairs Each
• 112 Total Connection Points
Mechanical:
Dimensions:
Features:
• Works with a wide variety and diameter
of lenses
• Allows lens to continue to turn and
telescope in and out while being
supported
• Easily retrofitted to an existing XL Mover
40.0 X 12.0 X 4.1”
Mechanical:
16” Height overall (adjustable)
5.50” width
2.0” depth
Weight: 3 lb (estimated)
Part Number
A000320-001
* Due to on-going development, features and specifications
subject to change without notice.
* Due to on-going development, features and specifications
subject to change without notice.
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
40
41
iMAGE MOVER
iMAGE MOVER Projection Transport System
MiT’s custom floor mounting track system permits two or more projection systems to be positioned laterally
in a projection booth. The projection systems may be film and digital, or any other combinations. The
track system allows either projection system to be on the projection centerline, even sharing the same
port window if necessary – eliminating the need to modify existing buildings. Projectors can also be
placed closer together to minimize image keystoning of either system while still permitting user access
as required. Even large equipment can be positioned with little effort and locked accurately into place.
Part Numbers:
B000200-001
C000351-006
C000360-001
C000360-102
C000360-104
C000361-001
C000362-001
C000362-102
C000362-104
CARRIER PLATFORM, PROJECTION SYSTEM (1 required per projector)
SPACER BLOCK, PROJECTION SYSTEM, 6” HEIGHT (optional, used in pairs)
TRACK, GUIDE RAIL, END (4’) [1220mm] (2 ends required per rail)
TRACK, GUIDE RAIL, EXTENSION (2’) [610mm]
TRACK, GUIDE RAIL, EXTENSION (4’) [1220mm]
LINK BAR, GUIDE RAIL (1 required for each joint in the guide rail)
TRACK, FLAT RAIL, END (4’) [1220mm] (2 ends required per rail)
TRACK, FLAT RAIL, EXTENSION (2’) [610mm]
TRACK, FLAT RAIL, EXTENSION (4’) [1220mm]
Using two track ends without an extension provides an 8’ [2440mm] usable track length.
This is the minimum stock length, add extensions to this as required to develop the length
needed. Contact MiT if a track length less than 8’ is desired, if you require the track
systems to be a single continuous piece, or if you need a custom height spacer.
Note: for the most precise positioning you may elect to use two guided rails forward and
rear, however a flat plate is generally used in the rear for better operator ergonomics.
Upgrades & Enhancements:
Features:
• Low profile rail (no trip hazard)
• Heavy-duty steel construction
• Continuous track lengths in custom lengths also available
• Platform height of 6”, standard
• Custom spacer heights also available
The system may also be modified to allow one or both projection systems to pivot up to
+/-4°. This is sometimes desired in the post production environment to allow side-by-side
projection simultaneously. For this modification the following additional item is available:
B000201-001
KIT, PROJECTOR PIVOT
Note: This upgrade requires the use of p/n C000351-006 spacer blocks, and they must have
relief slots machined for the projector mounting bolts to slide in. For this upgrade please
provide details on the specific projectors being mounted so the correct slot pattern may be
incorporated at the time of manufacture.
• Large urethane V-wheels with roller bearings
• Safety bumpers on carriers and track end
• Durable black powder coat finish
• Modular track, stock sections are combined to create any custom length
• Welded steel spacer blocks available to raise height in 6”increments (stock)
• Positive pin locking system for locating carriers in place
• Positive guide rail prevents dirt or obstructions from interfering with movement
* Due to on-going development, features and specifications
subject to change without notice.
• 1200lb [550kg] capacity
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
42
43
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
44
45
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
46
47
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
48
49
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
50
51
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
52
53
54
55
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
At the MOVING iMAGE TECHNOLOGIES Network Operations Center, we will ensure your Digital Cinema
Systems are monitored, even when your projection booth is not. MiT NOC services allow you to efficiently
develop your Theatre Technology Infrastructure without the stress of managing the assets. The MiT NOC
will remotely monitor your networked cinema assets 24 hours a day, 365 days a year and keep you
informed of your system health. Trained technicians monitor your systems so that if a problem arises,
the proper course of action is taken every time. We can assist in managing resolutions in the fastest
possible method by dispatching your service agency with the necessary information to resolve your
issue promptly, on the first attempt.
Features:
• 24/7/365 Health and Status Monitoring
• 24/7/365 Phone Support
• 24/7/365 Remote Support
• Early Detection of Problems
• Proactive Response and Correction
• Remote Firmware and Software
Upgrades
• Direct, Secure connection to your Digital
Cinema Network. (Via Your ISP)
• Reliable data logging via the iMAGE
WATCH server installed in your theatre.
• Cinedigm Certified
UPS
The iMAGE WATCH is the foundation of a reliable, monitored Digital Cinema System. The iMAGE WATCH
collects your TMS, Digital Projector, Screen Server, Automation and UPS health and status (SNMP) data
and relays it, in real time, to the MiT NOC. Digital Cinema Technicians monitor this information to
ensure any anomalies are addressed with the proper urgency to ensure maximum up time. The iMAGE
WATCH collects and distributes playback logs to keep you in compliance with VPF agreements.
Continuously Monitoring
• Direct Dispatch of your Service provider
(if required)
AUTOMATION
SCREEN SERVER
PROJECTOR
Network Operations Center
NETWORK OPERATION CENTER
iMAGE
WATCH
Monitoring the Heartbeat of Your Cinema System
Analyzed For Trends Possibly Indicating
•
•
•
•
•
•
•
•
• Temperatures
• Fan Speeds
• Storage Capacity
• Lamp Hours
• Error Messages
• Software Versions
• Seismic Foot Clamps
• Filter Hours
Overheating
Component Failure
Limited Storage Capacity
Network Issues
Lamp/Filter End of Life
Software Incompatibilities
Corrupted Content
KDM Expiration
• Consumables Management
* Due to on-going development, features and specifications
subject to change without notice.
Sales@movingimagetech.com | 1-866-MiT-8501 | movingimagetech.com
56
57