MATERIALS ENGINEERING DIRECTORATE
LIST OF APPROVED INDEPENDENT CALIBRATION LABORATORIES
As of 30th March 2016
Testing Laboratory
1
Al Hoty Analytical Services –
Calibration Department
2
Magnum Industrial Laboratories
W.L.L - Calibration Division
3
International Laboratory Services
- Calibration Section
Approval Given for Calibration Services on
Dimensional – calipers, micrometers, and dial indicators
Mechanical – scales and balances, torque wrenches, pressure gauges and
pressure indicators, force, compression and tension, rotational speed
Thermal – thermometers, thermocouples and RTD, ovens furnaces and
temperature bath, temperature (measure) and relative humidity
(measure)
Electrical – DC voltage, AC voltage, DC current, AC current, ohms, and
capacitance
Volume – laboratory volumetric apparatus
Weights
Stop Watch
Pressure (at laboratory) – gauges, recorders and safety valves
Mass (at laboratory) – weighing balance and glass wares
Mass (at site) – weighing balance
Force (at site) – compression mode
Thermal (at laboratory) – temperature indicator, controller with sensor,
thermocouples, RTDs, temperature gauge (analogue or digital) and
thermometer (slick type, glass or digital)
Generate - Electrical (at laboratory) – AC/DC voltage, AC/DC ampere and
resistance
Measure - Electrical (at laboratory) – AC/DC voltage, AC/DC ampere and
resistance
Dimensional – micrometers, calipers, height gauges, dial indicator / gauge,
plain plug gauge, dial thickness gauge, bore gauge (mechanism check
only), feeler gauge, pin gauge, bevel protector, combination set, dial
calibration tester and test sieve
REMARKS
Official Approval with TCR No. 448/15
Valid until 24/11/16
Renewal Under Process
Official Approval with TCR No. 450/15
Valid until 25/11/17
MATERIALS ENGINEERING DIRECTORATE
LIST OF APPROVED INDEPENDENT CALIBRATION LABORATORIES
As of 30th March 2016
Testing Laboratory
4
Universal Laboratories W.L.L Calibration Section
Approval Given for Calibration Services on
Electrical – AC/DC voltage (source and measure), AC/DC current (source,
simulate and measure), resistance (source and measure), capacitance
(source and measure), and electrical temperature simulation
(thermocouple and RTDs)
Time and Frequency – frequency (source and measure), stopwatches and
timers
Amount of Substance – ph meters and conductivity meters (excluding
probe)
Temperature – thermocouples, digital thermometers, resistance
thermometer, liquid in glass thermometers (partial immersion only),
ovens, incubators, mechanical (dial) thermometers and muffle furnaces)
Mass and Related Quantities – mass pieces, mass balances and scales,
volumetric glassware, hydraulic pressure gauges and compression
Dimensional – micrometers, Vernier calipers and height gauges, dial
gauges, standard weights (mass)
Mechanical – analytical balances, digital balances, platform balances,
pressure gauges, switches, recorders, valves, vacuum gauges, torque
wrenches, compression machine, tensile machine, pipettes, burettes,
etc.
Thermal – Generate (digital and glass type thermometers, PT100
thermocouples all types), Measure (oven, incubator, water bath,
temperature calibrators, temperature transmitters, chiller, freezer),
hotplate / thermo-cyclers, thermocouple and RTD Pt-100
Electrical – Generate (AC/DC voltage, AC/DC current and resistance) and
Measure (AC/DC voltage, AC/DC ampere, capacitance, resistance),
High Volt Measure (HV tester, cable test set), RCD Generate (RCD
REMARKS
Official Approval with TCR No. 449/15
Valid until 25/11/16
MATERIALS ENGINEERING DIRECTORATE
LIST OF APPROVED INDEPENDENT CALIBRATION LABORATORIES
As of 30th March 2016
Testing Laboratory
Approval Given for Calibration Services on
tester), Loop Generator (loop tester), Insulation Generate (insulation
tester) and Sound (sound level meter)
REMARKS