7060
7208
0682
INSTALLATION MANUAL
No forest has been destroyed to
produce this 100% recycled paper.
by GEMINI TRADING S.r.l. Via Luigi Galvani 12 21020 Bodio Lomnago (VA) Italia
Tel. +39 0332 943211 - Fax +39 0332 948080
E-mail : info@gemini-alarm.com
AC 2529 - REV. 00 / 06 / 01
GEMINI 7060
DESCRIPTION
The system 7060 is an alarm unit that can be installed on vehicles with 12 volts battery (negative earth).
FUNCTIONS
- Remote controlled alarm unit with dynamic code.
- Blinker, universal central door locking control, electric windows and sunroof closure for selected vehicles
equipped with “Pack Comfort” system.
- Perimetric protection and outlet for additional modules.
- Controls for self-powered siren, additional siren (continuous or alternate sound) and horn.
- LED’s Memory.
- Acoustic activation/de-activation (through siren or horn).
- Remote controlled panic function and / or boot opening.
- Electric engine immobilisation.
- Alarm unit functions programmable through the transmitter.
The unit is equipped with two 2-channel transmitters (art. 7208E), frequency 433.92 Mhz.
-
USEFUL SUGGESTIONS FOR THE INSTALLATION
Connect the positive and negative feeding wire of the alarm system to the battery.
Connect always the alarm Green-Brown wire to the door pin switch.
On catalysed vehicles the engine immobilisation must be carried out on the fuel pump and the starter motor.
Avoid routing connection wires next to interference sources.
The ultrasonic heads must be positioned at the top of each windscreen pillar and must be pointing at each
opposite diagonal corner away from the facia outlets.
WIRING CONNECTIONS
Disconnect the negative terminal of the battery and only re-connect after the installation is complete.
FUNCTION
WIRE COLOR
Earth
ð
BROWN
Battery positive terminal
ð
RED
Engine immobilisation (max. 10 A)
ð
2 X GREY
Ignition live
ð
YELLOW
Direction indicator lights
ð
2 x ORANGE
Door pin switch
ð
GREEN-BROWN
Boot/bonnet pin switches
ð
GREEN
Positive alarm armed
ð
PINK
External sensors inlet
ð
GREEN-BLACK
Self-powered siren control
ð
BLUE
Common +/- siren or klaxon
ð
BLACK
Additional siren or horn control
ð
YELLOW-BLACK
Negative control boot opening
ð
GREY-BLACK
Comfort
ð
WHITE-BLACK
Central door locking
ð
YELLOW-BLUE, RED-BLUE, YELLOW-GREY,
RED-GREY, YELLOW-BROWN, RED-BROWN
Note: The wiring harness has 2 connectors: connect the 2-pin connector to the LED and the 4-pin
connector to an additional module (shock, ultrasonic or super-high frequency module).
"DIP SWITCHES PROGRAMMING TABLE"
1
2
2
2
3
3
4
4
OFF
ON
OFF
ON
OFF
ON
OFF
ON
Comfort POSITIVE
Comfort NEGATIVE
Automatic arming OFF
Automatic arming ON
Self-learning of a new code OFF (normal use)
Self-learning of a new code ON
Closure short * period
Closure 6 seconds
* THE
SHORT TIME IS SET FROM THE PROGRAMMING WITH THE TWO-CHANNELS TRANSMITTER
BETWEEN 0,5 SECONDS AND 1 SECOND.
ATTENTION : SET THE DIP SWITCHES BEVOR FEEDING THE 7060 UNIT.
TABLE OF PROGRAMMABLE FUNCTIONS THROUGH THE TWO-CHANNELS TRANSMITTER.
ACTIONS
ALARM CONDITION
POWER OFF
Alarm OFF
Turn the ignition
Alarm OFF
key to ON
FEED THE UNIT
Alarm ON
7060
Press on the
Access to the Set-up 1 function:
transmitter 1 button
Supplementary siren
within 10 seconds
VISIBLE
ACTIONS
-
LED FLASHING AND
SELECTED FUNCTIONS
-
ALTERNATIVE
ACTIONS
-
-
-
-
-
-
-
One blinker
flashing
Press on the
transmitter 1 button
Access to the Set-up 2 function:
acoustic signalling with
supplementary siren 725
Two blinker
flashing
Press on the
transmitter 1 button
Access to the Set-up 3 function:
Panic and boot opening through
the transmitter
Three
blinker
flashing
Access to the Set-up 4 function:
Press on the
boot opening while alarm armed
transmitter 1 button
(Panic excluded)
Four blinker
flashing
Access to the Set-up 5 function:
Press on the
vehicle check while arming the
transmitter 1 button
system
Five blinker
flashing
Press on the
Access to the Set-up 6 function:
closure control period
transmitter 1 button
Six blinker
flashing
Access to the Set-up 7 function:
Press on the
Automatic arming with door
transmitter 1 button
closure
Seven
blinker
flashing
Press on the
Access to the Set-up 8 function:
transmitter 1 button
Comfort
Eight
blinker
flashing
Turn the ignition
key to OFF
Set-up exit, normal working
of the alarm
-
One flashing = continuous
Two flashing = intermittent
One flashing = de-activated
Two flashing = activated
One flashing = Panic and
additional siren
Two flashing = Boot opening
One flashing =
While alarm disarmed
Two flashing =
For both functions
One flashing = de-activated
Two flashing = activated
One flashing = 0,5 seconds
Press on the
transmitter
button N. 2 to
change the
selected option.
De-activate the
+15 to memorise
the selected
options and to
exit from User
set-up.
Two flashing = 1 seconds
One flashing = activated
Two flashing = de-activated
One flashing = while closing
Two flashing = after the
closure
-
-
1
2
3
4
5
6
7
8
Recapitulatory table of the programmable functions through the two -channels transmitter.
Function
Manufacturer function
Programmable function
Additional siren outlet
Continuous sound
Alternate sound
Acoustic signalling
De-activated
Activated
Boot opening with alarm disarmed
De-activated
Activated
Boot opening with alarm armed
With alarm disarmed if the 3
Both functions
functions has been activated
(Panic excluded)
Vehicle’s check
Central door locking short period
Automatic arming
Comfort
De-activated
0,5 seconds
Activated
While closing the doors
Activated
1 second
De-activated
After the blinker flashing
WORKING DESCRIPTION
- ALARM ARMING: press on the transmitter’s button N. 1. One pulse of the direction indicator lights signals
the arming.
- EXCLUSION OF THE VOLUMETRIC SENSOR, EXTERNAL SENSORS AND COMFORT CONTROL
AFTER THE ALARM ARMING: while alarm armed (even if the boot opening function with alarm armed is
activated), during the inhibit time (Led lightning fix) press on the transmitter 2 button. The exclusion is
signalled by one pulse of the direction indicator lights, the comfort function and the sensors are excluded.
This function de-activates at the first arming of the alarm.
- ALARM DISARMING: press on the transmitter’s button N. 1.
The disarming is signalled through 3 pulses of the direction indicator lights or 5 pulses if an alarm condition
has occurred.
SPECIAL FUNCTIONS
SELF-LEARNING OF THE CODE OF A NEW TRANS MITTER.
The self-learning of a new transmitter can be obtained with two different ways:
1. While alarm disarmed set the dip switch N.3 to ON and turn the ignition key to ON. The Led and the direction
indicator lights activate. Turning the ignition key to OFF the Led and the direction indicator lights switch off.
Press on the new transmitter button N. 1 within 8 seconds.
For each new code it is necessary to turn the ignition key to ON for one second and then to OFF.
At the end of the self-learning operation set the dip switch N.3 to OFF.
2. While alarm disarmed, open the driver’s door, turn the ignition key to ON and press on the coded transmitter
button N. 2. The Led and the direction indicator lights activate. Turning the ignition key to OFF the Led and
the direction indicator lights switch off. Press on the new transmitter’ s button N. 2 within 10 seconds.
For each new code it is necessary to turn the ignition key to ON for one second and then to OFF.
At the end of the self-learning operation, after 10 seconds the system works normally.
NOTE: the system is supplied with a maximum number of 3 transmitters.
AUTOMATIC ARMING
To obtain this function set the dip switch N. 2 to ON. 60 seconds after the disarming of the alarm, if the doors
and the boot are not opened and the ignition key is not turned to ON, the system will arm with or without closing
the vehicles doors (according to setting of the set-up 7 function).
REMOTE CONTROLLED BOOT OPENING.
The alarm unit 7060 allows opening the vehicle boot if the control is electric to negative. To obtain this function
select the set-up 3 function and press on the transmitter button N. 2 with the alarm disarmed.
If the boot opening is carried out pressing on the transmitter 2 button with the alarm armed (after selecting the
set-up 4 function), the panic function will de-activate and all the inlets inhibit for 60 seconds. If the boot is not
closed within this delay time the alarm will trigger. The opening of the boot through the transmitter is signalled
by one pulse of the direction indicator lights.
PANIC FUNCTION
To obtain this function with the alarm armed after the neutral time, press on the transmitter button N. 2 (if the 4
function- boot opening with alarm armed is de-activated). The siren, the klaxon and the direction indicator lights
activate. To de-activate this function within the 10 seconds of the alarm cycle, press on the transmitter button
N. 2.
LEDS MEMORY.
While disarming the alarm, turn the ignition key to ON to check if an attempted break-in has occurred.
Following the Led flashing it is possible to know the alarm triggering’s cause. The signalisation is repeated for
5 times.
Signalling LED
Alarm triggering
¬¬l¬¬
Door and boot/bonnet pin switches.
¬¬¬l¬¬¬
Ignition live
¬¬¬¬l¬¬¬¬
External sensors
l LED OFF (2 seconds) ¬ LED ON (1 second)
Each alarm cycle is 30 seconds
The inhibit time is 30 seconds for all alarm triggering’s cause.
Alarm cycle
10
Unlimited
10
TRANSMITTERS BATTERY DISCHARGING
The discharging of the battery is signalled through the LED of the
transmitter. If the LED flashes while pressing one of the transmitter’s
buttons it is necessary to replace the batteries.
BATTERIES: CR1616
Note: put the batteries in the appropriate container.
Power supply
Working temperature
Max. Current drawn alarm OFF
Transmitters frequency
Direction indicator lights relay contact capability
Engine immobilisation relay contact capability
Outlet horn relay contact capability
Central door locking relay contact capability
TECHNICAL DATA
10.5-14.5 V dc.
-40° C + 85°C
15 mA (with self-powered siren connected)
433.92 MHz
8A dc
8A dc
8A dc
8A dc
GEMINI 7147
DESCRIPTION.
GEMINI 7147 is 2 wires, high power electronic siren designed to be installed quickly and simply in the engine compartment.
WIRING CONNECTIONS (for the installer)
Disconnect the negative terminal of the battery and only re-connect after the installation is complete.
WIRE COLOUR
FUNCTION
RED
é
Battery positive terminal (12V)
BLACK
é
To the alarm YELLOW -BLACK wire.
NOTE: connect the BLACK wire of the unit to earth.
INSTALLATION.
Install the siren in the engine compartment using the bracket and the screws supplied with the kit. Install the siren away from
areas of intense heat and turn to low the siren ear trumpet to avoid water infiltration.
Protect the wires from water and humidity and to avoid any damaging do not steam clean directly to the siren.
GEMINI 7025
DESCRIPTION.
Gemini 7025 is a self-powered, high power, electronic siren studied to install in the vehicle’s engine compartment. To install
the siren in the engine compartment use the bracket and the screws supplied with the kit and follow the fitting instructions.
Install the siren on the vehicles bodywork away from areas of intense heat.
WIRING CONNECTIONS (for the installer)
Disconnect the negative terminal of the battery and only re-connect after the installation is complete.
WIRE COLOUR
FUNCTION
BLACK marked RB
ê Battery positive terminal
BLACK marked MB
ê Battery negative terminal
BLACK marked S
ê To the alarm PINK wire
BLACK marked R
ê To the alarm RED wire
BLACK marked L
ê To the alarm BLUE wire
NOTE: connect the BLACK wire of the unit to earth.
Connect one end of the BLACK initialled V wire to the bonnet pin switch and the other end to the alarm GREEN wire.
NOTE: To disarm the alarm unit and the engine immobilisation, turn the siren key to off. The internal battery recharges
with alarm disarmed.
Power supply
Current absorption alarm ON
Current absorption alarm OFF
Audible tone
TECHNICAL DATA
12V
3mA
7Ma (recharging battery).
> 118dB
Note: To avoid any damaging do not steam clean directly to the siren.
GEMINI 725
DESCRIPTION.
Gemini 725 is a self-powered, high power, electronic siren studied to install in the vehicle’s engine compartment. To install the
siren in the engine compartment use the bracket and the screws supplied with the kit and follow the fitting instructions.
Install the siren on the vehicles bodywork away from areas of intense heat.
WIRING CONNECTIONS (for the installer)
Disconnect the negative terminal of the battery and only re-connect after the installation is complete.
WIRE COLOUR
FUNCTION
RED
BLACK
BLUE
ê Battery positive terminal
ê Battery negative terminal
ê To the alarm unit YELLOW-BLACK wire
NOTE: connect the BLACK wire of the unit to earth.
INSTALLATION.
Install the siren in the engine compartment away from areas of intense heat using the bracket and the screws supplied with the kit.
TECHNICAL DATA
Power supply
12V
Current absorption
7mA (recharging battery)
Audible tone
> 118dB
Note: to avoid any damaging do not steam clean directly to the siren.
This device is guaranteed against any manufacturing or working fault for 12 months from purchase date. The manufacturer declines
every responsibility for any defect or failure to the device and to the electric plant of the vehicle due to an incorrect installation or to the
alteration of the technical data stated in this manual.
Fitting diagram
ref.7060
Supplementary siren Gemini 7147 and Gemini 7060 interface
Push-botton 2
Push-botton 1
ON
7060
ON
Optional
7059
1 2 3 4
Emergency Push-botton
1 2 3 4
RED
7060
Ultrasonic Module
5123
+
-
RED
Red
Black
15A
YELLOW-BLACK
BLACK
BLACK
NEGATIVE
RED
Pink
Brown
BROWN
EARTH
External Sensor inlet
YELLOW-BLUE
RED-BLUE
YELLOW-GREY
RED-GREY
YELLOW-BROWN
RED-BROWN
Refer to central door locking diagrams
BATTERY
12VOLT
Comfort
ORANGE
5A
ORANGE
SIREN POSITIONING
Direction indicators lights
GREEN-BROWN
GREY
Door pin switches
_
+
WHITE-BLACK
5A
OK
GREY
8A
MAX !
GREEN
Engine immobilisation
Boot/Bonnet pin switch
BLACK
Common (+/-) for siren or clacson
NOTE: negative control for siren
BLUE
NO!
GREY-BLACK
(Negative control)
Self-Powered Siren
Trunk release
YELLOW-BLACK
Control for supplementary siren or clacson
File : 7060centrale-UK CDR
CLAMP
+30
RED
+
RED
Battery
12 VOLT
Green-Black
7147
10A
+30
Ignition Key
5A
Diagram 2
Diagram 4
1 2 3 4
1 2 3 4
7060
ON
7060
4 OFF
ON
4 OFF
+30
YELLOW-GREY
+30
RED-GREY
YELLOW-BLUE
Common,Comune,Comun,
Je nuch Z.V.
RED-BLUE
YELLOW-GREY
RED-GREY
YELLOW-BROWN
Open,Apre,Ouvre,Auf,Apertura,Abre
Close,Chiude,Ferme,Zu,Cierre,Fecha
RED-BROWN
RED-BLUE
YELLOW-BROWN
YELLOW-BLUE
Vehicles original
door lock switch
Not connected, Non collegare, Ne pas brancher, No conectar, Nicht verbinden
RED-BROWN
Not connected, Non collegare, Ne pas brancher, No conectar, Nicht verbinden
Close
M
M
Open
EX : ALFA,FIAT,FORD,LANCIA,OPEL,PEUGEOT,RENAULT,SAAB,SEAT,VW POLO(95-99)
EX : RENAULT TWINGO (<2000)
Diagram 3
1 2 3 4
7060
ON
Diagram 5
4 ON
1 2 3 4
7060
+30
ON
4 OFF
+30
YELLOW-GREY
RED-GREY
YELLOW-GREY
YELLOW-BROWN
RED-GREY
RED-BLUE
YELLOW-BROWN
RED-BROWN
RED-BROWN
YELLOW-BLUE
YELLOW-BLUE
GREEN
RED-BLUE
BLUE
Ref.2305T
Original
Motor
COMPRESSOR
EX : AUDI 80,MERCEDES 190
EX : HONDA CIVIC 5p(96) PRELUDE(96),HYUNDAI LANTRA(96),ACCENT(96),GALLOPER(98)
Diagram 8
Diagram 6
1 2 3 4
ON
Negative Comfort
7060
1 2 3 4
ON
7060
1 ON
4 ON
4 OFF
+30
YELLOW-GREY
RED-GREY
Slave motor
ref. 2306T
+30
WHITE-BLACK
YELLOW-BROWN
YELLOW-GREY
Close
YELLOW-BROWN
RED-BLUE
Common
RED-BROWN
Open
YELLOW-BLUE
BLACK
WHITE
BROWN
RED-BROWN
YELLOW-BLUE
RED-BLUE
Original switch
RED-GREY
BLUE
COMPRESSOR
GREEN
COMFORT,CONFORT,KOMFORT
EX : DAEWOO NEXIA,OPEL FRONTERA (<99).
Original
Motor
BLUE (Mercedes)
AUDI 100,MERCEDES WITH PACK-COMFORT SISTEM(<96).
Diagram 7
Diagram 9
1 2 3 4
1 2 3 4
7060
ON
1 OFF
4 OFF
ON
YELLOW-GREY
RED-GREY
YELLOW-BROWN
RED-BROWN
POSITIVE
Open,Apre,Ouvre,Auf,Apertura,Abre
YELLOW-BLUE
Negative Comfort
YELLOW-GREY
RED-GREY
WHITE-BLACK
YELLOW-BROWN
Not connected, Non collegare, Ne pas brancher, No conectar, Nicht verbinden
RED-BROWN
Close,Chiude,Ferme,Zu,Cierre,Fecha
+ COMFORT, CONFORT, KOMFORT
EX : BMW 3(<98),5(<96),7-8(96),Z3(97>)
Common,Comune,Comun,
Je nuch Z.V.
RED-BLUE
Not connected, Non collegare, Ne pas brancher, No conectar, Nicht verbinden
WHITE-BLACK
1 ON
4 OFF
+30
+30
RED-BLUE
ON
Positive Comfort
7060
Positive Comfort
YELLOW-BLUE
1 2 3 4
1 OFF
4 OFF
Open,Apre,Ouvre,Auf,Apertura,Abre
Close,Chiude,Ferme,Zu,Cierre,Fecha
COMFORT,CONFORT,KOMFORT
Not connected, Non collegare, Ne pas brancher, No conectar, Nicht verbinden
Not connected, Non collegare, Ne pas brancher, No conectar, Nicht verbinden
EX : AUDI A4, A6(<96),OPEL VECTRA(<96),OMEGA, SEAT TOLEDO (<96)
Diagram 10
1 2 3 4
1 2 3 4
1 OFF
4 OFF
ON
1 ON
4 OFF
ON
Positive Comfort
7060
Diagram 23
Negative Comfort
1 2 3 4
ON
7060
4 OFF
+30
RED-GREY
RED-BLUE
YELLOW-BROWN
Common,Comune,Comun,
Je nuch Z.V.
YELLOW-BLUE
RED-BLUE
YELLOW-GREY
Open,Apre,Ouvre,Auf,Apertura,Abre
WHITE-BLACK
YELLOW-GREY Not connected, Non collegare, Ne pas brancher, No conectar, Nicht verbinden
RED-BROWN
Close,Chiude,Ferme,Zu,Cierre,Fecha
+ Comfort,Confort,Komfort
RED-GREY
YELLOW-BLUE
Not connected, Non collegare, Ne pas brancher, No conectar, Nicht verbinden
YELLOW-BROWN Not connected, Non collegare, Ne pas brancher, No conectar, Nicht verbinden
RED-BROWN
Not connected, Non collegare, Ne pas brancher, No conectar, Nicht verbinden
EX:AUDI A3,A6(97>),BMW 3(98),5(96>),OPEL ASTRA(98),SKODA OCTAVIA,VW GOLF,PASSAT
Diagram 22
1 2 3 4
7060
ON
CENTRAL
DOOR
LOCKING
L.H.S
door
EX : CITROEN XSARA, FIAT ULISSE (98), LANCIA Z (98),PEUGEOT 206, 306, 406.
Gemini 2344 or 2343 and Gemini 7060 interface
4 OFF
1 2 3 4
ON
YELLOW-GREY
RED-BLUE
Negative
1 OFF
7060
2344
+30
YELLOW-BROWN
RED-GREY
Negative
Not connected, Non collegare, Ne pas brancher, No conectar, Nicht verbinden
RED-BROWN
WHITE-RED
YELLOW-BLUE
CENTRAL
DOOR
LOCKING
L.H.S
door
EX : NISSAN MICRA(>97), PRIMERA, SUBARU FORESTER, SUZUKI IGNIS, JIMMY.
WHITE-BROWN
PINK
ROSA
ROSE
WHITE-BLACK
BIANCO-NERO
BLANC-NOIR
BLANCO-NEGRO
WEISS-SCHWARZ
Supplementary siren Gemini 7147 and Gemini 7060 interface
Self-powered siren 7025 with 7060 interface
Emergency Push-botton
7025
7060
CLAMP
BLACK
GREEN
BLACK marked S
RED
BLUE
BLACK marked R
BLACK marked L
BLACK marked RB
RED
YELLOW-BLACK
BLACK
BLACK
NEGATIVE
15A
RED
_
+
_
+
BATTERY
12VOLT
BATTERY
12VOLT
Self-powered siren 725 with 7060 interface
SIREN POSITIONING
Emergency Push-botton
725
RED
7060
OK
10A
+30
RED
Not connected
RED
WHITE
BLACK
YELLOW-BLACK
RED
BLACK
NEGATIVE
+
BATTERY
12VOLT
_
5A
BLACK
CLAMP
+30
RED
BLACK marked MB
Black marked V
7147
10A
CLAMP
PINK
RED
7060
NOTE:The Black wires have
the identification mark in the end.
NO!
5A