TWP-CF - Acuity Brands

Catalog
Number
Notes
FEATURES & SPECIFICATIONS
INTENDED USE — For entrances, loading docks, walkways and vehicle ramps.
CONSTRUCTION — Rear housing: Rugged, corrosion-resistant, die-cast aluminum. Corrosion-resistant
external hardware includes slotted hex-head and tamperproof fasteners.
Type
Front housing and refractor: One-piece, injection-molded, UV-stabilized polycarbonate.
Wall Packs
Finish: Dark Bronze (DDB) corrosion resistant polyester powder.
OPTICS — Reflector is finished in white thermoset polyester powder, electrostatically applied. Standard
finish on opaque portion of front cover and back housing is dark bronze polyester enamel. Refractor is sealed
and gasketed to inhibit the entrance of outside contaminants.
TWP
ELECTRICAL — Ballast: Class P, multi-volt electronic, high power factor, <10%THD, with starting temperature of 0°F (-18°C).
Socket: High temperature thermoplastic with an integral lamp retention clip.
INSTALLATION — Top 3/4" threaded wiring access. Back access through removable 3/4" knockout.
Feed-thru wiring can be achieved by using a condulet tee. Mount on any flat, vertical surface. NOTE: Not
recommended for use in car wash interior applications.
COMPACT FLUORESCENT: 26DTT - 2/42TRT
8' to 15' Mounting
LISTINGS — Listed and labeled to UL standards. Listed and labeled to CSA standards (see Options). UL
listed for 25°C ambient and wet location. IP64 rated.
Note: Specifications subject to change without notice.
Specifications
Height: 15-1/2 (39.4)
Width: 16-1/8 (41.0)
15-1/2
(39.4)
Depth: 7-3/4 (19.7)
*Weight: 16 lbs. (7 kg)
All dimensions are inches (centimeters)
unless otherwise indicated.
* Weight as configured in example below.
ORDERING INFORMATION
16-1/8
(41.0)
7-3/4
(19.7)
Example: TWP 2/32TRT MVOLT LPI
Lead times will vary depending on options selected. Consult with your sales representative.
TWP
Series
Wattage
Voltage
TWP
26DTT
2/26DTT
26TRT
2/26TRT
32TRT
2/32TRT
42TRT
2/42TRT
120
277
347
MVOLT1
Ballast
(blank) Electronic 0° F
Options
Finish
Shipped installed in fixture
GMF Internal slow-blow fusing2
GLR
Internal fast-blow fusing2
BDP
Ballast disconnect
EC
Emergency circuit2
ELDWC Emergency battery pack (-4° F min operating temp)2, 4
PE
Photoelectric cell – button type2
CSA
Listed and labeled to CSA Standards
FS
Full shield
Shipped separately5
WG
Wire guard
(blank)
DBL
DMB
DWH
DNA
DSS
CR
CRT
Lamp6
Dark bronze
Black
Medium bronze
White
Natural aluminum
Sandstone
Enhanced corrosion-resistant
finish
Non-stick protective coating7
LPI Lamp included
L/LP Less lamp
Notes
OUTDOOR
1
2
3
4
Optional multi-volt electronic ballast capable of operating on any line voltage from 120V-277V.
Must specify voltage; not available with MVOLT.
Maximum allowable wattage lamp included.
For 2-lamp configurations, only one lamp operates in emergency backup mode. ELDWC with
5
6
May be ordered as an accessory with prefix TWP.
Must be specified. (35K lamp with LPI)
compact fluorescent does not satisfy North Carolina code criteria for state owned buildings per 2012 NC
Building Code: 1006.3 and 1006.4.
TWP-CF
TWP Compact Fluorescent Wall Packs
TWP-CF
OUTDOOR: One Lithonia Way Conyers, GA 30012 Phone: 770.922.9000 Fax: 770-918-1209 www.lithonia.com © 2006-2013 Acuity Brands Lighting, Inc. All rights reserved. Rev. 03/26/13