IR RECEIVER MODULE Application Guide OPTO ELECTRONICS ■ Type Designation Code R 9 4 F H 1 A [Type Description] [Holder Configuration] - 1: No Holder, 2~: Holder Type [Lead Configuration] - Top View: H, Side View: V, Custom: S,C [Frequencies] 32.7 36.7 37.9 40.0 56.7 D E F G J [PIN Configuration] - 2: 1=GND, 2=Vcc, 3=Vout - 4: 1=Vout, 2=GND, 3=Vcc - 6: 1=Vout, 2=Vcc, 3=GND [Package Configuration] - SMD Type: 1, 7, 8 - DIP Type: 2, 3, 8, 9 [IR Receiver Module] ■ Type Description Supply Voltage OEC Product Characteristics Performance R□□□□□A Standard R□□□□□C High Noise Immunity R□□□□□D Short Burst Compatible, High Speed R□□□□□H Standard Low Current 2.7~5.5V ■ Disturbance Suppression Characteristics R□□□□□A R□□□□□C R□□□□□D R□□□□□H Most standard flourescent Lamps ++ ++ ++ ++ Most standard flourescent Lamps (with weak ballast) ++ ++ + ++ Most standard flourescent Lamps (with strong ballast) + ++ - + [Note] ++ : Best Suppression, + : Suppression in most cases, - : Possibility of disturbance pulses IR RECEIVER MODULE Application Guide OPTO ELECTRONICS ■ Suitable Data Format for IR Receiver Module Code Type R□□□□□A R□□□□□C R□□□□□D R□□□□□H NEC + + + + RC-5 + + + + RC-6 + + + + Toshiba Micom Code + + + + Sharp Code + + + + Sony 12-Bit Code + - + + Sony 15-Bit Code - - + - Sony 20-Bit Code - - + - RCA Code - - + - RCMM Code - - + - Matsushita Code + + + + Mitsubishi Code - - + - Zenith Code + + + + JVC Code + - + + Data communication - - - - [Note] ++ : Best Suppression, + : Suppression in most cases, - : Possibility of disturbance pulses ■ Transmitter Burst Signal Format Characteristics Symbol Standard Noise Short Burst Low Current Minimum Burst Length tBurst 300㎲ 300㎲ 150㎲ 300㎲ Minimum Gap Time between the bursts tGap 300㎲ 300㎲ 250㎲ 300㎲ tPause 25㎳ 30㎳ 10㎳ 25㎳ Minimum Data Pause Time between the data word - Standard type need a data pause time (longer than 25㎳) at least each 100㎳, or each data word. - Noise type need a data pause time (longer than 30㎳) at least 100㎳, or each data word. - Short burst type need a data pause time (longer than 10㎳) at least each data word. [Fig.1 Typical Data Signal] Data word tPause enlarge tPreburst Carrier Frequency : 32~40kHz tBurst tGap (Output pulse) - tBurst: length of a burst in pulse of the carrier frequency - tGap: length of the gap between two burst in pulses of carrier. - tPreburst: leader code of data word. IR RECEIVER MODULE SMD/DIP Type (R□□□□□A) OPTO ELECTRONICS ■ Features ◆ High ripple rejection ◆ Wide operating voltage: 2.7 ~ 6.0V ◆ Maximum interference safety against optical and electrical ◆ Internal filter for a high frequency lighting fluorescent lamp. ◆ Short setting time after power on (below 1㎳) ■ Description ◆ The series are miniaturized receiver for use in infrared remote control system. ◆ It consist of automatic gain control amplifier, post amplifier, oscillator, automatic gain control circuit, a band pass filter, a signal waveform detection circuit, automatic threshold control circuit, a waveform rectifier. ■ Applications ◆ All household electric appliances such as TV, DVD, air conditioner and audio equipment. ■ Electrical Characteristics Parameter [Vcc=5.0V, Ta=25℃] Symbol Supply Voltage Vcc Supply Current Icc Peak Wavelength Λp B.P.F Center Frequency ※) Fo High Level Output Voltage VOH Low Level Output Voltage VOL High Level Output Pulse Width tWH Low Level Output Pulse Width tWL Arrival Distance D Condition No signal input Typ Max Unit 2.7 - 6.0 V 0.5 1.0 1.5 ㎃ - 940 - ㎚ ㎑ 37.9 - Vcc-0.2 - V 0.2 0.4 V 400 - 800 ㎲ 400 - 800 ㎲ 0˚ 12 - - m ±30˚ 10 - - m Burst Wave = 600㎲ Period = 1.2㎳ Output Form ※) Available for Carrier Frequencies between 32.7㎑ to 40.0㎑ ■ Block Diagram Min Active Low Output IR RECEIVER MODULE SMD/DIP Type (R□□□□□C) OPTO ELECTRONICS ■ Features ◆ High ripple rejection ◆ Wide operating voltage: 2.7 ~ 6.0V ◆ Maximum interference safety against optical and electrical ◆ Internal filter for a high frequency lighting fluorescent lamp. ◆ Short setting time after power on (below 1㎳) ■ Description ◆ The series are miniaturized receiver for use in infrared remote control system. ◆ It consist of automatic gain control amplifier, post amplifier, oscillator, automatic gain control circuit, a band pass filter, a signal waveform detection circuit, automatic threshold control circuit, a waveform rectifier. ■ Applications ◆ All household electric appliances such as TV, DVD, air conditioner and audio equipment. ■ Electrical Characteristics Parameter [Vcc=5.0V, Ta=25℃] Symbol Supply Voltage Vcc Supply Current Icc Peak Wavelength Λp B.P.F Center Frequency ※) Fo High Level Output Voltage VOH Low Level Output Voltage VOL High Level Output Pulse Width tWH Low Level Output Pulse Width tWL Arrival Distance D Condition No signal input Typ Max Unit 2.7 - 6.0 V 0.5 1.0 1.5 ㎃ - 940 - ㎚ ㎑ 37.9 - Vcc-0.2 - V 0.2 0.4 V 400 - 800 ㎲ 400 - 800 ㎲ 0˚ 12 - - m ±30˚ 10 - - m Burst Wave = 600㎲ Period = 1.2㎳ Output Form ※) Available for Carrier Frequencies between 32.7㎑ to 40.0㎑ ■ Block Diagram Min Active Low Output IR RECEIVER MODULE SMD/DIP Type (R□□□□□D) OPTO ELECTRONICS ■ Features ◆ High ripple rejection ◆ Wide operating voltage: 2.7V ~ 6.0V ◆ Maximum interference safety against optical and electrical ◆ Internal filter for a high frequency lighting fluorescent lamp. ◆ Short setting time after power on (below 1㎳) ■ Description ◆ The series are miniaturized receiver for use in infrared remote control system. ◆ It consist of automatic gain control amplifier, post amplifier, oscillator, automatic gain control circuit, a band pass filter, a signal waveform detection circuit, automatic threshold control circuit, a waveform rectifier. ■ Applications ◆ All household electric appliances such as TV, DVD, air conditioner and audio equipment. ■ Electrical Characteristics Parameter [Vcc=5.0V, Ta=25℃] Symbol Supply Voltage Vcc Supply Current Icc Peak Wavelength Λp B.P.F Center Frequency ※) Fo High Level Output Voltage VOH Low Level Output Voltage VOL High Level Output Pulse Width tWH Low Level Output Pulse Width tWL Arrival Distance D Condition No signal input Typ Max Unit 2.7 - 6.0 V 0.5 1.0 1.5 ㎃ - 940 - ㎚ ㎑ 37.9 - Vcc-0.2 - V 0.2 0.4 V 400 - 800 ㎲ 400 - 800 ㎲ 0˚ 12 - - m ±30˚ 10 - - m Burst Wave = 600㎲ Period = 1.2㎳ Output Form ※) Available for Carrier Frequencies between 32.7㎑ to 40.0㎑ ■ Block Diagram Min Active Low Output IR RECEIVER MODULE SMD/DIP Type (R□□□□□H) OPTO ELECTRONICS ■ Features ◆ Low current consumption ◆ High ripple rejection ◆ Wide operating voltage: 2.7 ~ 6.0V ◆ Maximum interference safety against optical and electrical ◆ Enhanced immunity against all kinds of disturbance light and power noise ◆ Short setting time after power on (below 1㎳) ■ Description ◆ The series are miniaturized receiver for use in infrared remote control system. ◆ It consist of automatic gain control amplifier, post amplifier, oscillator, automatic gain control circuit, a band pass filter, a signal waveform detection circuit, automatic threshold control circuit, a waveform rectifier. ■ Applications ◆ All household electric appliances such as TV, DVD, air conditioner and audio equipment. ■ Electrical Characteristics Parameter [Vcc=3.3V, Ta=25℃] Symbol Supply Voltage Vcc Supply Current Icc Peak Wavelength Λp B.P.F Center Frequency ※) Fo High Level Output Voltage VOH Low Level Output Voltage VOL High Level Output Pulse Width tWH Low Level Output Pulse Width tWL Arrival Distance D Condition No signal input Typ Max Unit 2.7 - 5.5 V 0.3 0.48 0.6 ㎃ - 940 - ㎚ ㎑ 37.9 - Vcc-0.2 - V 0.2 0.4 V 400 - 800 ㎲ 400 - 800 ㎲ 0˚ 12 - - m ±30˚ 10 - - m Burst Wave = 600㎲ Period = 1.2㎳ Output Form ※) Available for Carrier Frequencies between 32.7㎑ to 40.0㎑ ■ Block Diagram Min Active Low Output