LED LIGHT FIXTURES
ARTICLE:
MNST1L (60 LED) Range Performance
TECHNICAL DESCRIPTION. Rev. A – September 2011
Attachment
Suitable for lateral installation only on Ø 10.2 cm pipe.
92,5 cm
34 cm
Side
Front
14 cm
Conformity
In compliance with EN 60598-1 and EN 60598-2-3.
Absence of photobiological risk: Group 1 (EN 62471:2008; IEC-TR
623471-2:2009).
Dimensions and Weight - Coverage
Height – 14cm; length – 92.5cm; width – 34cm
Weight – 20Kg
Area exposed to wind pressure CxS = 0.08m²
Materials
Structure made from long-lasting and recyclable materials: die cast
aluminium. Stainless steel and brass fasteners.
Structure and Main Components
Upper single-shell frame with clamp coupling for attachment to the
support;
Lower tilting frame for accessing the compartment holding the auxiliary
devices and optics.
Silicone gasket between the upper and lower frames.
60-LED module with moulded polycarbonate (PC) shield and refractive
lens for each individual LED.
Internal aluminium heat sink.
Electronic power supply unit with auto diagnostics functions.
Double-pole isolator.
Fuse holder.
General features
Voltage 230 V (±15%)
Frequency 50/60 Hz.
Class II insulation
Protection rating IP66
Rated power 61 - 135 W (variable depending on configuration).
Emitted flux 6,000 – 10,800 lm (variable depending on configuration).
Mean luminous efficacy: 68 lm/W (3000K); 86 lm/W (4000K).
Colour temperature 3000K (± 5% warm - white) or 4000K (± 5% neutral - white).
Power factor cos φ ≥ 0.99 (use PFC).
Operating temperature -30°C – +50°C.
Terminals for wires with a max. section of 2.5 mm²
Fuse 400V 6A – 8.5X31.5 mm (ceramic cartridge).
Estimated life-expectancy 80,000 hours (L70 – Ta 25°C – at maximum power).
System warranty 24 months (60 months on request).
Light source
60-LED module on a MCPCB (metal core printed circuit board) with
aluminium multilayer heat sink, designed as a system which can be
updated over time.
Two possible optic systems with refractive lenses (impact resistance
rating IK10):
1) optics for street lighting (satisfies ME lighting classes).
2) optics for mixed areas (streets, roundabouts, car parks – satisfies CE lighting
classes).
Operation and Maintenance
This system has been designed to facilitate maintenance operations
without the use of tools. The appliance can by opened by releasing
the special handle on the front and then lowering the bottom frame:
no component actually comes away from the structure. On opening a
disconnector switch automatically cuts of the power supply.
Power supply unit not attached to the LED module and can be replaced
separately.
LED module can be replaced separately.
No maintenance required except for periodical cleaning of the lens to
remove dust and dirt.
Appliance in compliance with light pollution containment and energy
savings, approved by: Unione Astrofili Italiani – (Italian Union of
Amateur Astronomers)
© 2011 NERI S.p.A.
Optics with installation geometry for mixed areas – CE lighting
classes
Optics with installation geometry for street lighting – ME lighting
classes
LED LIGHT FIXTURES
ARTICLE:
MNST1L (60 LED) Range Performance
TECHNICAL DESCRIPTION. Rev. A – September 2011
Driver
Adjustable electronics with auto diagnostic functions for temperature
control.
Driver optional extras
On request the appliance can be fitted with a special driver with various
optional systems such as:
1) Constant luminous flux control throughout the system's lifetime by
means of current regulation
2) Stand-alone flux adjustment for energy savings on preset seasonal
programs
3) Dimming by means of 1-10V protocol
4) Dimming by means of DALI protocol.
Configurations based on luminous flux output
The appliance is supplied based on luminous flux output, depending on
real lighting needs. All the driver’s automatic adjustments remain active for
each luminous flux output.
LED module designed as an open system which can be updated over time
in relation to technological evolution of the light sources.
Luminous flux output
Colour Temp. 4000K
Colour Temp. 3000K
Flux (lm)
Power (W)
lm/W
Power (W)
lm/W
no. of LEDs
10800
135
80
//
//
60
9000
105
85
136
66
60
7500
83
90
114
65
60
6000
65
92
85
70
60
4500
//
//
61
73
60
Sectors of use
Height of installation between 6 – 9 metres.
Protection of surfaces – technical performance features of the paint
In order to ensure quality and high resistance of articles over time, the
paint products used have the following performance features:
Resistance to QUV
∆E less than 2 after 2,000 hours of exposure according to
testing in compliance with UNI ISO 11507.
This value is certified with certification issued by an
independent body.
Resistance to corrosion
Resistance to salt spray test higher than 1,500 hours according
to testing in compliance with UNI ISO 9227.
This value is certified with certification issued by an
independent body.
Standard paint colour
Dark Grey Matt Metallic (type Neri) and RAL 9007.
Notes
Class I insulation on request.
Appliance in compliance with light pollution containment and energy
savings, approved by: Unione Astrofili Italiani – (Italian Union of
Amateur Astronomers)
© 2011 NERI S.p.A.
Special heat dissipation system