ATTACHMENTS
6020 Series Tractors
Issue 03/2008
EAME
John Deere Werke Mannheim
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
6020 Series Tractors-1
ATTACHMENTS - FACTORY AND FIELD INSTALLED
A short description and recommendation of some of
the various factory and field installations is given.
Please note that the information, codes bundle
numbers are given for reference only, the current
price list must be the only official ordering
document.
Where factory installation codes or field installation
bundle numbers were not available, they will be made
available as soon as possible.
1 Drive System
1.1 CREEPER KITS
Bundle
Description
Remark
QTY
for
open
operator’s
station
L171602 Spacer
2
tractors
L79408
Spring clip
1
AL165238 Kit of spare parts for tractors up to serial
1
for intake lines
number 392088
B15646
O-ring
2
L155450 Clamp
2
L155471
Slotted disk
2
for 4 cyl. tractors
up to serial number
487435;
for 6 cyl. tractors up to
AL117414 U-joint, drive shaft serial number 487435 with 1
disk brake housing with 47
mm (1.85 in.) in length
Code
Bundle
AL162433
Description
Creeper kit, PowrQuad transmission,
4 ranges
Models: without cab: 6020 - 6620,
low profile open station: 6020 - 6420
6020SE - 6620SE
Note: Depending on the options of the tractor,
additional spare parts may be required, e.g.
panel. Please use the corresponding spare parts
catalog.
Bundle
AL173947
AL151613
AL173948
AL151610
AL155072
R119441
R150858
AL174966
Description
Push-pull cable,
1050 mm length
Clutch cable with
absorber
Push-pull cable,
1160 mm length
Clutch cable with
absorber
Oil line
Arm, clutch outer
Bracket, clutch
Loadcenter
bracket
Remark
QTY
for 4 cyl. tractors
1
for 4 cyl. tractors
1
for 6 cyl. tractors
1
for 6 cyl. tractors
1
1
1
1
for open operator’s station 1
tractors
for 4 cyl. tractors
from serial number
487436;
AL165470 U-joint, drive shaft for 6 cyl. tractors from
1
serial number 487436 with
disk brake housing with 47
mm (1.85 in.) in length
for 6 cyl. tractors up to
serial number 496374 with
AL117418 U-joint, drive shaft disk brake housing with 30 1
mm (1.18 in.) in length
for 6 cyl. tractors from
AL167208 U-joint, drive shaft serial number 496375 with 1
disk brake housing with 30
mm (1.18 in.) in length
6020 Series Tractors-2
Code
Bundle
AL157233
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Description
Creeper kit, PowrQuad transmission,
6 ranges
Code
Bundle
AL157055
Issue 03-2008 (EAME)
Description
Creeper kit, PowrQuad Plus or
AutoQuad transmission, 6 ranges
Models: cab only: 6320 - 6420S
Models: cab only: 6120 - 6620
Note: up to tractor serial number 376372
Note: up to tractor serial number 376372
Note: Depending on the options of the tractor,
additional spare parts may be required, e.g.
panel. Please use the corresponding spare parts
catalog.
Note: Depending on the options of the tractor,
additional spare parts may be required, e.g.
panel. Please use the corresponding spare parts
catalog.
Bundle
Bundle
Description
Push-pull
cable,
AL173947
1050 mm length
Push-pull cable,
AL173948
1160 mm length
Code
Bundle
AL162172
Remark
QTY
not for HCS
1
with HCS
1
Description
Creeper kit, PowrQuad Plus or
AutoQuad transmission,
6 ranges
Code
Bundle
AL162171
Remark
QTY
6120 - 6420S
1
6120 - 6420S with HCS,
6520, 6620
1
Description
Creeper kit, PowrQuad Plus or
AutoQuad transmission, 6 ranges
Models: cab only: 6120 - 6620
Models: cab only: 6320 - 6420S
Note: from tractor serial number 376373
Note: from tractor serial number 376373
Note: Depending on the options of the tractor,
additional spare parts may be required, e.g.
panel. Please use the corresponding spare parts
catalog.
Bundle
Description
AL160792 Housing
cable,
AL173947 Push-pull
1050 mm length
cable,
AL173948 Push-pull
1160 mm length
Description
AL173947 Push-pull cable,
1050 mm length
Push-pull cable,
AL173948
1160 mm length
Remark
QTY
1
not for HCS
1
with HCS
1
Note: Depending on the options of the tractor,
additional spare parts may be required, e.g.
panel. Please use the corresponding spare parts
catalog.
Bundle
Description
AL160792 Housing
Push-pull cable,
AL173947 1050 mm length
cable,
AL173948 Push-pull
1160 mm length
Remark
QTY
1
6120 - 6420S
1
6120 - 6420S with HCS,
6520, 6620
1
Issue 03-2008 (EAME)
Code
Bundle
AL162432
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Description
Creeper kit, SyncroPlus transmission,
4 ranges
Note: Depending on the options of the tractor,
additional spare parts may be required, e.g.
panel. Please use the corresponding spare parts
catalog.
AL173947
AL151610
AL173948
AL151614
Description
Push-pull cable,
1050 mm length
Clutch cable with
absorber
Push-pull cable,
1160 mm length
Clutch cable with
absorber
AL117412 U-joint, drive shaft
AL168625 U-joint, drive shaft
AL117420 U-joint, drive shaft
AL168631 U-joint, drive shaft
Kit of spare parts for
AL165238 intake lines
AL154623 Formed hose, assy.
AL154624 Formed hose, assy.
19M7662
M10 x 30 cap screw
Remark
QTY
for 4 cyl. tractors
1
for 4 cyl. tractors
1
for 6 cyl. tractors
1
for 6 cyl. tractors
1
for 4 cyl. tractors
up to serial number
487412
for 4 cyl. tractors
from serial number
487413
for 6 cyl. tractors
up to serial number
487394
for 6 cyl. tractors
from serial number
487395
for tractors up to
serial number
392660
up to serial number
345650
up to serial number
345650
Bundle
AL162434
Description
Creeper kit, SyncroPlus transmission
with PowrReverser, 4 ranges
Models: without cab: 6020 - 6620,
6020SE - 6620SE (not for low profile)
Models: without cab: 6020 - 6620,
low profile open station: 6020 - 6420,
6020SE - 6620SE
Bundle
Code
6020 Series Tractors-3
1
Note: Depending on the options of the tractor,
additional spare parts may be required, e.g.
panel. Please use the corresponding spare parts
catalog.
Bundle
AL174966
Description
Push-Pull cable,
1050 mm length
Clutch cable with
absorber
Push-Pull cable,
1160 mm length
Clutch cable with
absorber
Loadcenter
bracket
L171602
Spacer
AL173947
AL151610
AL173948
AL151614
1
1
AL117414 U-joint, drive shaft
Remark
QTY
for 4 cyl. tractors
1
for 4 cyl. tractors
1
for 6 cyl. tractors
1
for 6 cyl. tractors
1
for open operator’s station 1
tractors
for open operator’s station 2
tractors
for 4 cyl. tractors
up to serial number
487435;
1
for 6 cyl. tractors up to
serial number 487435 with
disk brake housing with 47
mm (1.85 in.) in length
1
1
1
1
1
AL165470 U-joint, drive shaft
for 4 cyl. tractors
from serial number
487436;
1
for 6 cyl. tractors from
serial number 487436 with
disk brake housing with 47
mm (1.85 in.) in length
1
AL117418 U-joint, drive shaft for 6 cyl. tractors up to
serial number 496374 with
disk brake housing with 30
mm (1.18 in.) in length
6 cyl. tractors from
AL167208 U-joint, drive shaft for
serial number 496375 with
disk brake housing with 30
mm (1.18 in.) in length
Kit
of
spare
parts
for
tractors up to serial
AL165238
for intake lines
number 392553
B15646
O-ring
L155450 Clamp
L155471 Slotted disk
L80044
Bracket
for tractors with front
AL114289 Oil line
wheel drive only
1
1
2
2
2
2
1
6020 Series Tractors-4
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Issue 03-2008 (EAME)
1.2 COVERS
Code
Bundle
AL157237
Description
Creeper kit, PowrQuad Plus or
AutoQuad transmission
These covers are recommended when driving under
adverse working conditions like scrub and woodland.
Models: cab only: 6820
Note: Depending on the options of the tractor,
additional spare parts may be required, e.g.
panel. Please use the corresponding spare parts
catalog.
Bundle
AL155419
L154239
L154240
L158529
AL155074
Description
Heater hose
Formed hose
Oil cooler hose
Y-connector
Oil line assy.
AL156590
Bracket
L154166
RE201075
14M7273
19M7162
Code
Shield flywheel,
side left TLS
Shaft, transmission
output with bushing
Nut (M8)
Cap screw
Bundle
AL157238
Remark
with suspended front
axle
with suspended front
axle
QTY
1
1
1
1
1
1
1
1
1
1
Description
Creeper kit, PowrQuad Plus or
AutoQuad transmission
Models: cab only: 6920, 6920S
Note: Depending on the options of the tractor,
additional spare parts may be required, e.g.
panel. Please use the corresponding spare parts
catalog.
Bundle
AL155419
L154239
L154240
L158529
AL155076
Description
Heater hose
Hose, formed
Oil cooler hose
Y-connector
Oil line assy.
Remark
AL156590
Bracket
with suspended front 1
axle
with suspended front 1
axle
L154166
RE201075
14M7273
19M7162
Shield flywheel,
side left TLS
Shaft, transmission
output with bushing
Nut (M8)
Cap screw
QTY
1
1
1
1
1
1
1
1
Code
Bundle
AL163214
Description
Covers for electro-magnetic
shift valves
Models: cab only: 6120 - 6920S
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
6020 Series Tractors-5
2 HYDRAULICS
2.1 MECHANICALLY-ACTUATED
SELECTIVE CONTROL VALVES M-SCV
300 and 301 Series M-SCVs can basically be used in
all positions, but if possible they should be installed on
the left hand side (M-SCV at pos. 1 or 2). When
installing them on the right hand side (M-SCV at pos.
3 or 4), an additional parts kit is necessary.
M-SCV Identification
• 100 or 101 Series (Standard): mechanically
actuated, with fixed cap
• 200 or 201 Series (DeLuxe): mechanically
actuated, with three operating positions
• 300 or 301 Series (Super DeLuxe): mechanically
actuated, with three operating positions
100 Series M-SCV
The M-SCVs provide a full range of features which
gives the flexibility to operate all hydraulic equipment
on the farm. The M-SCVs are located at the rear of the
tractor, at either side of the hitch valve. ISO scs are
mounted to each M-SCV.
Three different M-SCV versions are available:
100 resp. 101 Series, 200 resp. 201 Series or 300 resp.
301 Series.
100, 200 and 300 Series M-SCVs can only be used
with PFC hydraulic system with axial piston pump.
101, 201 and 301 Series M-SCVs can only be used
with PC or HydraVantage hydraulic systems with
gear pump.
This valve features:
• A 4 position lever control that is detented as
standard
• Flow of up to 60 l/min is available through the
valve
• Removable detent collar
• 4-way operation
• Automatic detent release (if detent is fitted) when
the engine is switched off.
6020 Series Tractors-6
ATTACHMENTS - FACTORY AND FIELD INSTALLED
The M-SCV field kit also contains the corresponding
quick couplers and dust protection. The below listed
control and mounting parts have to be ordered
separately according to the mounting position of the
M-SCV.
Code Bundle
AL169787
Description
M-SCV Series 100 with 2 ISOstandard quick couplers and dust
protection housing
Models: 6020 - 6920S
101 Series M-SCV
This valve features: see 100 Serie M-SCV
The M-SCV field kit also contains the corresponding
quick couplers and dust protection. The below listed
control and mounting parts have to be ordered
separately according to the mounting position of the
M-SCV.
Code Bundle
AL169788
Control and mounting parts
Description
AL169859
Control and mounting
parts
AL169860
Control and mounting
parts
Remark
QTY
for tractors up to
serial number
1
375300
for tractors from
serial number
1
375301
For M-SCV installation on Position II
Bundle
AL169859
Description
Control and mounting
parts
Remark
Description
M-SCV Series 101 with 2 ISOstandard quick couplers and dust
protection housing
Models: 6020 - 6620 (without cab), 6020SE - 6620SE
For M-SCV installation on Position I
Bundle
Issue 03-2008 (EAME)
Control and mounting parts
For M-SCV installation on Position I
Bundle
Description
AL169859
Control and mounting
parts
AL169860
Control and mounting
parts
QTY
Remark
QTY
for tractors up to
serial number
1
375300
for tractors from
serial number
1
375301
1
For M-SCV installation on Position II
Bundle
For M-SCV installation on Position III
Bundle
AL169861
Description
Remark
Control and mounting
parts and spacer housing
QTY
AL169859
Description
Control and mounting
parts
Remark
QTY
1
1
For M-SCV installation on Position III
For M-SCV installation on Position IV
(not for tractors with AutoPowr transmission)
Bundle
AL169862
AL153498
Description
Single lever control,
2 functions and mounting
parts
Shifter rod for single
lever control, consoleintegrated
Remark
QTY
controls M-SCV
on Position III and 1
IV
for tractors up to
serial number
398655 with
PowrQuad Plus 1
or AutoQuad
transmission
Bundle
AL169861
Description
Remark
Control and mounting
parts and spacer housing
QTY
1
For M-SCV installation on Position IV
(not for tractors with AutoPowr transmission)
Bundle
AL169862
AL153498
Description
Single lever control,
2 functions and mounting
parts
Shifter rod for single
lever control, consoleintegrated
Remark
QTY
controls M-SCV
on Position III and 1
IV
for tractors up to
serial number
398655 with
PowrQuad Plus 1
or AutoQuad
transmission
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
200 Series M-SCV
6020 Series Tractors-7
For M-SCV installation on Position II
Bundle
AL169859
Description
Control and mounting
parts
Remark
QTY
1
For M-SCV installation on Position III
Bundle
AL169861
Description
Remark
Control and mounting
parts and spacer housing
QTY
1
For M-SCV installation on Position IV
(not for tractors with AutoPowr transmission)
In addition to the features of 100 Series valves, 200
Series M-SCV features:
• A variable flow control, from zero to maximum
flow, and 2-way selectable detents
• 96 l/min. maximum flow (not with 60 l/min.
pump)
• Selectable detents allow the switching between
’No detent’, ideal for loader operation, and
’Mechanical detent’, for continuous hydraulic
motor operation
• Flow infinitely adjustable from 0 to 96 l/min.
• The control dial is located on the M-SCV and may
be reached from the operator’s seat
• Neutral start protection releases lever to neutral
when the engine is switched off
• A load check valve on the raise/extend port
prevents loader and implement linkage creep
Bundle
AL169862
AL153498
Description
Single lever control,
2 functions and mounting
parts
Shifter rod for single
lever control, consoleintegrated
Remark
QTY
controls M-SCV
on Position III and 1
IV
for tractors up to
serial number
398655 with
1
PowrQuad Plus
or AutoQuad
transmission
201 Series M-SCV
This valve features: see 200 Serie M-SCV
The M-SCV field kit also contains the corresponding
quick couplers and dust protection. The below listed
control and mounting parts have to be ordered
separately according to the mounting position of the
M-SCV.
The M-SCV field kit also contains the corresponding
quick couplers and dust protection. The below listed
control and mounting parts have to be ordered
separately according to the mounting position of the
M-SCV.
Code Bundle
Code Bundle
AL169789
Description
M-SCV Series 200 with 2 ISO-DeLuxe
quick couplers and dust protection
housing
Models: 6020 - 6920S
Models: 6020 - 6620 (without cab), 6020SE - 6620SE
Control and mounting parts
For M-SCV installation on Position I
Bundle
Description
AL169859
Control and mounting
parts
AL169860
Control and mounting
parts
AL169790
Description
M-SCV Series 201 with 2 ISO-DeLuxe
quick couplers and dust protection
housing
Remark
QTY
for tractors up to
serial number
1
375300
for tractors from
serial number
1
375301
6020 Series Tractors-8
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Control and mounting parts
For M-SCV installation on Position I
Bundle
Description
AL169859
Control and mounting
parts
AL169860
Control and mounting
parts
Remark
QTY
for tractors up to
serial number
1
375300
for tractors from
serial number
1
375301
For M-SCV installation on Position II
Bundle
AL169859
Description
Control and mounting
parts
Remark
QTY
1
For M-SCV installation on Position III
Bundle
AL169861
Description
Remark
Control and mounting
parts and spacer housing
QTY
1
For M-SCV installation on Position IV
(not for tractors with AutoPowr transmission)
Bundle
AL169862
AL153498
Description
Single lever control,
2 functions and mounting
parts
Shifter rod for single
lever control, consoleintegrated
Remark
QTY
controls M-SCV
on Position III and 1
IV
for tractors up to
serial number
398655 with
PowrQuad Plus 1
or AutoQuad
transmission
Issue 03-2008 (EAME)
In addition to all the features of 200 Series M-SCVs,
300 Series M-SCVs incorporate a temperature
compensated adjustable flow restrictor which
continuously regulates the flow of oil between zero
and maximum in both directions regardless of oil
temperature.
This will give day-long constant speed operation of
hydraulic motors and rams without the need for
adjustment.
Selectable detents allow the operator to choose the
same modes as the 200 Series M-SCVs, and in
addition a hydraulic detent, where the M-SCV lever
will remain selected until a pre-set pressure is reached.
It will then ’kickout’ of the detent to the neutral
position automatically. This mode is particularly useful
when repeat M-SCV operations are performed, such as
turning a plough or drill marker cycling.
The M-SCV field kit also contains the corresponding
quick couplers and dust protection. The below listed
control and mounting parts have to be ordered
separately according to the mounting position of the
M-SCV.
Code Bundle
AL169791
Description
M-SCV Series 300 with 2 ISO-DeLuxe
quick couplers and dust protection
housing
Models: 6020 - 6920S
Control and mounting parts
For M-SCV installation on Position I
Bundle
Description
AL169859
Control and mounting
parts
AL169860
Control and mounting
parts
300 Series M-SCV
Remark
QTY
for tractors up to
serial number
1
375300
for tractors from
serial number
1
375301
For M-SCV installation on Position II
Bundle
AL169859
Description
Control and mounting
parts
Remark
QTY
1
For M-SCV installation on Position III
Bundle
AL169861
AL169957
Description
Remark
QTY
Control and mounting
1
parts and spacer housing
if on Pos III or IV
has not yet been
Right hand End Cover
installed a
1
and connecting parts
M-SCV Series
300/301 or an
E-SCV
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
For M-SCV installation on Position IV
(not for tractors with AutoPowr transmission)
Bundle
AL169862
AL153498
AL169957
Description
Single lever control,
2 functions and mounting
parts
Shifter rod for single
lever control, consoleintegrated
Right hand End Cover
and connecting parts
Remark
controls M-SCV
on Position III and
IV
for tractors up to
serial number
398655 with
PowrQuad Plus
or AutoQuad
transmission
if on Pos III or IV
has not yet been
installed a
M-SCV Series
300/301 or an
E-SCV
6020 Series Tractors-9
Control and mounting parts
QTY
1
1
For M-SCV installation on Position I
Bundle
Description
AL169859
Control and mounting
parts
AL169860
Control and mounting
parts
Remark
QTY
for tractors up to
serial number
1
375300
for tractors from
serial number
1
375301
For M-SCV installation on Position II
1
Bundle
AL169859
Description
Control and mounting
parts
Remark
QTY
1
For M-SCV installation on Position III
Bundle
AL169861
301 Series M-SCV
AL169957
Description
Remark
Control and mounting
parts and spacer housing
Right hand End Cover
and connecting parts
QTY
1
1
This valve features: see 300 Series M-SCV
The M-SCV field kit also contains the corresponding
quick couplers and dust protection. The below listed
control and mounting parts have to be ordered
separately according to the mounting position of the
M-SCV.
Code Bundle
AL169792
Description
M-SCV Series 301 with 2 ISO-DeLuxe
quick couplers and dust protection
housing
For M-SCV installation on Position IV
(not for tractors with AutoPowr transmission)
Bundle
AL169862
Description
Single lever control,
2 functions and mounting
parts
AL153498
Shifter rod for single
lever control, consoleintegrated
AL169957
Right hand End Cover
and connecting parts
Models: 6020 - 6620 (without cab), 6020SE - 6620SE
Remark
controls M-SCV
on Position III and
IV
for tractors up to
serial number
398655 with
PowrQuad Plus
or AutoQuad
transmission
if on Pos III or IV
has not yet been
installed a
M-SCV Series
300/301 or an
E-SCV
QTY
1
1
1
6020 Series Tractors-10
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Issue 03-2008 (EAME)
Additional shut-off valves for selective
control valves
The shut-off valves can be installed to prevent leakage
at the hydraulic SCV connections.
Code Bundle
Code Bundle
AL174687
Description
Shut-off valve
AL163533
Description
Left hand End Cover with additional
connection
Models: 6020 - 6920S, 6020SE - 6520SE
Models: 6020 - 6920S, 6020SE - 6620SE, 6215, 6515
SCV End Covers
Possible SCV End Covers - Left hand
Code Bundle
AL163534
Description
Left hand End Cover with pressureand LS port
Models: 6320 - 6920S
Code Bundle
AL77028
Description
Left hand End Cover assembly,
standard
Models: 6020 - 6920S, 6020SE - 6620SE
Note:
for suspended cab; paint operation for service
needed
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
6020 Series Tractors-11
Possible SCV End Covers - Right hand
Code Bundle
AL77680
Description
Right hand End Cover assembly,
standard
Models: 6020 - 6920S
Code
Bundle
AL158831
Description
Special End Cover for external control
unit on right hand side
Models: 6020 - 6920S, 6020SE - 6520SE, 6215, 6515
Code Bundle
AL160414
Description
Right hand End Cover with 300 Series
SCV (position 3 and 4)
Models: 6020 - 6920S, 6520SE, 6215, 6515
Note:
for 6020 - 6620 with PC and PFC systems
for 6820 - 6920S with PFC system
for 6020SE - 6520SE with PC system
for 6215, 6515 with HydraVantage hydraulic
system
Note:
Depending on the options of the tractor,
additional spare parts may be required.
Bundle
Description
AL157634
hydraulic hose,
475mm length
AL157635
hydraulic hose,
420 mm length
AL157636
hydraulic hose,
380 mm length
Remark
for 6820 - 6920S
with SCV at
position 3
for 6820 - 6920S
without SCV at
position 3
for 6020 - 6620
with or without
SCV at position 3
QTY
1
1
1
6020 Series Tractors-12
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Issue 03-2008 (EAME)
Kit for return connection on hydraulic
motor (PC-system and PFC-system)
Code
Bundle
AL169965
Description
Pressure-free return circuit
Models: 6020 - 6920S, 6020SE - 6620SE, 6215, 6515
Note: On PC hydraulic systems, the hydraulic motor
return must not be used continuously at
maximum oil withdrawal.
Note: If a hydraulic coupler socket is required instead
of internal half coupler AL81368, please order
part AL81369 separately.
Code Bundle
AL118486
Description
Right hand End Cover, Power Beyond
(with pressure-, return- and LS port)
with Power Boost
Models: 6120 - 6920S, 6020SE - 6620SE
Note:
Power Beyond Plate
with ICV
Power Beyond Application Valve
Power beyond allows the use of the tractor pump to
power implements that have ICV (independent control
valves) or orbital motors. For functions requiring
additional hydraulic power, the power beyond plate
replaces the fourth SCV. Pressure return and load
sensing ports are provided for hook-up of additional
equipment, such as ICV, front loader etc.
Code
Bundle
AL112428
Description
Power Beyond Application valve
Models: 6020 - 6920S, 6020SE - 6520SE
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
6020 Series Tractors-13
Power Beyond Coupler on rockshaft valve
In addition to the Power Beyond plate this kit includes
two female and two male couplers, two hydraulic
lines, dust protection and hardware. ICV’s controlled
implements or attachments connected to the hydraulic
system of the tractor are provided with a Pressure-OnDemand (POD)-signal, pressured oil and a pressurefree return line. Connection/disconnection is eased by
quick coupler.
Code Bundle
EC300182
Description
Power Beyond Coupler on rockshaft
valve
Models: 6020 - 6620
Code Bundle
AL82290
Description
Power Beyond Coupler on rockshaft
valve
Models: 6020 - 6620
Note: includes left hand End Cover AL163533 (with
the Load Sense connection)
Note: For ICV’s without POD a special valve block is
required.
Note: up to tractor serial number 398655
Note: please order in addition AL158831 (End Cover
for external control unit on right hand side)
Note: from tractor serial number 398656
6020 Series Tractors-14
ATTACHMENTS - FACTORY AND FIELD INSTALLED
2.2 M-ICV AND E-ICV
Mechanical Independent Control Valve
(M-ICV) - 2 section
The M-ICV (mechanical independent control valve) is
a separate control valve block unite mounted below the
right hand side of the cab. It is fitted below the cab and
supplied with hydraulic power through the Power
Beyond valve or ICV-Cover.
It is ideal for single lever control of front loader or
front hitch work.
The valve features functions similar to that of two
SCVs.
• 1st function features: extend neutral retract and a
detented float position
• 2nd function: extend neutral retract
• The M-ICV is not detented for hydraulic motors
• Both functions feature a flow capacity of 96 l/min.
at stand-by pressure and proportional flow
• When a 96 l/min pump is fitted, maximum flow
capacity can be achieved with reduced engine rpm
for more comfortable operation
• More than one function may be operated
simultaneously to speed up operations and save
time
• Proportional valves give fine adjustment for
inching and operation acceleration/deceleration
during long travel movements
• A balance valve between the two functions ensures
that both may be operated at once, ensuring
professional operation capability, for example
raise boom and roll back bucket
Issue 03-2008 (EAME)
Spool movement is no longer achieved mechanically,
but electrically through stepper motors (similar to the
precise, reliable and proven stepper motor rear hitch
control).
Valve Functions
All 3 valves feature proportional flow and a flow
capacity of 96 l/min. at stand-by pressure.
Lever movements are transformed into electric
impulses inducing - if required - minute movements
for precise stacking or loading operations
• This unique fine adjustment allows inching
operation or acceleration/ deceleration during
longer piston travel movements
• Up to three functions may be operated
simultaneously to speed up manoeuvres while
ensuring professional, parallel operation capability
• The selectable shake-out position permits
optimum bucket cleaning through automatic
vibration mode when overriding the position for
max. dump speed
• Allows pre-compaction during back blading in
float position
*Only when the three SCVs option is chosen,
automatically the option for the fourth and fifth SCVs
is provided.
M-ICV and E-ICV field kits
Code
Bundle
AL159273
Description
M-ICV & E-ICV field kit
Models: cab only: 6120 - 6620, 6020SE - 6520SE
Electrical Independent Control Valve
(E-ICV) - 2 or 3 sections
Note: not for low profile tractors
Note: up to tractor serial number 398655
Note: Depending on the options of the tractor,
additional spare parts may be required.
The E-ICV is a separate control valve unit mounted
below the right-hand side of the cab with the functions
of two or optionally three* SCVs.
Bundle
Description
AL155376
Oil line (pressure)
AL155377
Oil line (LS)
AL155378
Oil line (return)
AL116239
Oil line (pressure)
AL116240
Oil line (LS)
AL116241
Oil line (return)
AL157634
Hydraulic hose (LS)
AL157636
Hydraulic hose (LS)
AL159274
AL159296
Service kit M-ICV, 2
section
Service kit E-ICV,
2 section
Remark
with suspended
cab
with suspended
cab
with suspended
cab
without
suspended cab
without
suspended cab
without
suspended cab
with PC hydr.
system
with PFC hydr.
system
QTY
1
1
1
1
1
1
1
1
for M-ICV
1
for E-ICV
1
Issue 03-2008 (EAME)
Bundle
AL159297
AL164525
AL164526
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Description
Service kit E-ICV,
3 section
Wiring harness
transmission rear, E-SCV
or E-ICV
Wiring harness
transmission rear, E-ICV
AL157528
Wiring harness
transmission rear,
ECE or SAE with E-SCV
or E-ICV
AL159344
Joystick for E-ICV control
AL159345
Joystick for E-ICV control
AL116589
Joystick for M-ICV control
AL153498
Shifter rod with grip,
autoshift
Code
Bundle
AL159275
Remark
QTY
for E-ICV
1
with
CommandArm
1
for E-ICV without
CommandArm
for E-ICV without
CommandArm;
not required for
suspended front
axle or Premium
Plus tractors
for E-ICV without
CommandArm
for E-ICV with
CommandArm
for M-ICV
with AutoQuad or
PowrQuad Plus
transmission
1
Bundle
Description
AL157527
AL159344
AL159345
1
AL116589
AL153498
1
6020 Series Tractors-15
Remark
for E-ICV without
CommandArm;
Wiring harness
not required for
transmission rear,
tractors with HCS
ECE with E-SCV or Eor Premium Plus
ICV
tractors
for E-ICV without
Joystick for E-ICV control
CommandArm
for E-ICV with
Joystick for E-ICV control CommandArm
Joystick for M-ICV control for M-ICV
with AutoQuad or
Shifter rod with grip,
PowrQuad Plus
autoshift
transmission
QTY
1
1
1
1
1
1
1
1
Description
M-ICV & E-ICV field kit
M-ICV with multi-function lever
A mechanically operated multi-function lever may be
fitted to the front corner of the right hand console in
the cab to control up to two SCVs. The lever is useful
for one touch operations of either one or two SCV
controlled implements, and of particular interest where
use is frequent, for example with front hitch control.
Models: cab only: 6820 - 6920S
Note: up to tractor serial number 398655
Note: Depending on the options of the tractor,
additional spare parts may be required.
Bundle
Description
AL155379
Oil line (pressure)
AL155380
Oil line (LS)
AL155381
Oil line (return)
AL116242
Oil line (pressure)
AL116243
Oil line (LS)
AL116244
Oil line (return)
AL157634
Hydraulic hose (LS)
AL157635
Hydraulic hose (LS)
AL159274
AL159296
AL159297
AL164525
AL164526
Service kit M-ICV, 2
section
Service kit E-ICV,
2 section
Service kit E-ICV,
3 section
Wiring harness
transmission rear, E-SCV
or E-ICV
Wiring harness
transmission rear, E-ICV
Remark
with suspended
cab
with suspended
cab
with suspended
cab
without
suspended cab
without
suspended cab
without
suspended cab
with SCV at pos. 3
without SCV at
pos. 3
QTY
1
1
1
1
1
1
1
Code
1
for M-ICV
1
for E-ICV
1
for E-ICV
1
with
CommandArm
1
for E-ICV without 1
CommandArm
Bundle
AL117838
Description
M-ICV field kit with multi-function lever
Models: low profile cab only: 6020SE - 6620SE
Note: up to tractor serial number 398655
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Note: Depending on the options of the tractor,
additional spare parts may be required.
Bundle
L113757
L114010
Description
Holder
Suction hose,
L = 1020 mm
Remark
QTY
1
1
6020 Series Tractors-16
Bundle
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Description
Hose ID 25 630 mm
Special screw,
M14 x 110
L114011
L113893
L114657
Bracket
L114658
Exhaust pipe
L113323
Bracket
Remark
only with exhaust stack to
bottom right
only with exhaust stack to
bottom right
only with exhaust stack to
bottom right
QTY
Bundle
Description
1
AL116243
Load sensing line
1
AL116244
Return line
1
AL163527
Pressure line
1
AL155380
Load sensing line
1
AL155381
Return line
Code
M-ICV field kits - 2 section
Code
Bundle
AL162450
Models: cab only: 6020 - 6920S,
6020SE - 6620SE (not with low profile cab,
not for tractors with CommandArm)
Note: from tractor serial number 398656
Note: If M-ICV and power beyond spacer without SCV
pos. 3 is used, order additionally 3 x L169846
(screw).
Note: If M-ICV and power beyond spacer with SCV
pos. 3 is used, order additionally 3 x R95614
(screw).
Note: Depending on the options of the tractor,
additional spare parts may be required.
Description
AL164711
Basic Kit
AL116239
Pressure line
AL163522
Load sensing line
AL163523
Return line
AL155376
Pressure line
AL163525
Load sensing line
AL163526
Return line
AL116536
Pressure line
AL116537
Load sensing line
AL116538
Return line
Bundle
AL164710
Description
Basic Kit
AL163524
Pressure line
Remark
6020 - 6620,
6020SE - 6620SE
with unsuspended
cab
with unsuspended
cab
with unsuspended
cab
with suspended
cab
with suspended
cab
with suspended
cab
with open
operator’s station
with open
operator’s station
with open
operator’s station
Bundle
AL164712
Description
M-ICV field kit
Bundle
Issue 03-2008 (EAME)
Remark
with unsuspended
cab
with unsuspended
cab
with suspended
cab
with suspended
cab
with suspended
cab
QTY
1
1
1
1
1
Description
M-ICV field kit with power beyond plate
and needed oil lines
Models: cab only: 6020SE - 6420SE
(with low profile cab)
Note: from tractor serial number 398656
Note: If M-ICV and power beyond spacer without SCV
pos. 3 is used, oder additionally 3 x L169846
(screw).
Note: If M-ICV and power beyond spacer with SCV
pos. 3 is used, order additionally 3 x R95614
(screw).
E-ICV field kits - 2 or 3 sections
QTY
1
1
Code
Bundle
AL159296
Description
E-ICV field kit with 2 sections
Models: cab only: 6120 - 6920S
Note: from tractor serial number 398656
1
1
1
1
1
Note: If E-ICV and power beyond spacer without SCV
pos. 3 is used, oder additionally 3 x L169846
(screw).
Note: If E-ICV and power beyond spacer with SCV
pos. 3 is used, order additionally 3 x R95614
(screw).
Note: Depending on the options of the tractor,
additional spare parts may be required.
1
Bundle
AL164711
Description
Basic Kit
1
AL116239
Pressure line
1
AL163522
Load sensing line
AL163523
Return line
AL155376
Pressure line
AL163525
Load sensing line
Remark
QTY
6820 - 6920S
1
with unsuspended 1
cab
Remark
6120 - 6620
with unsuspended
cab
with unsuspended
cab
with unsuspended
cab
with suspended
cab
with suspended
cab
QTY
1
1
1
1
1
1
Issue 03-2008 (EAME)
Bundle
Description
AL163526
Return line
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Remark
with suspended
cab
Bundle
AL164710
Description
Basic Kit
AL163524
Pressure line
AL116243
Load sensing line
AL116244
Return line
AL163527
Pressure line
AL155380
Load sensing line
AL155381
Return line
Code
Bundle
AL159297
Remark
6820 - 6920S
with unsuspended
cab
with unsuspended
cab
with unsuspended
cab
with suspended
cab
with suspended
cab
with suspended
cab
6020 Series Tractors-17
QTY
Bundle
Description
1
AL116243
Load sensing line
AL116244
Return line
QTY
1
AL163527
Pressure line
1
AL155380
Load sensing line
1
AL155381
Return line
Remark
with unsuspended
cab
with unsuspended
cab
with suspended
cab
with suspended
cab
with suspended
cab
QTY
1
1
1
1
1
1
1
1
1
Flow control for E-ICV
Description
E-ICV field kit with 3 sections
Models: cab only: 6120 - 6920S
Note: from tractor serial number 398656
Note: If E-ICV and power beyond spacer without SCV
pos. 3 is used, oder additionally 3 x L169846
(screw).
Note: If E-ICV and power beyond spacer with SCV
pos. 3 is used, order additionally 3 x R95614
(screw).
Note: Depending on the options of the tractor,
additional spare parts may be required.
Bundle
AL164711
Description
Basic Kit
AL116239
Pressure line
AL163522
Load sensing line
AL163523
Return line
AL155376
Pressure line
AL163525
Load sensing line
AL163526
Return line
Bundle
AL164710
Description
Basic Kit
AL163524
Pressure line
Remark
6120 - 6620
with unsuspended
cab
with unsuspended
cab
with unsuspended
cab
with suspended
cab
with suspended
cab
with suspended
cab
QTY
1
Code
1
Models: 6120 - 6920S
1
1
1
1
1
Remark
QTY
6820 - 6920S
1
with unsuspended
1
cab
Bundle
AL170031
Description
Flow control for E-ICV
Note: from tractor serial number 398656
Note: Depending on the options of the tractor,
additional spare parts may be required.
Bundle
AL166106
AL166108
Description
Instrument, dual gauge
plus II/ECE
Instrument, dual gauge
plus II/ECE
Remark
QTY
without AutoPowr
1
transmission
with AutoPowr
1
transmission
6020 Series Tractors-18
ATTACHMENTS - FACTORY AND FIELD INSTALLED
2.3 ELECTRICALLY-ACTUATED
SELECTIVE CONTROL VALVE E-SCV
The electrically-actuated SCVs with adjustable flow
rates and timed detents are exclusively available for
the 6020 Series John Deere Premium Plus cab models .
A programmable electronic controller controls SCV
functions via a solenoid in each valve. The valve has
no direct control linkage. Out of this result the
following advantages:
• Eases operator effort, reducing shift forces and
fatigue in repetitive operations.
• Reduced wear of parts and lower maintenance
costs.
SCV controls are located in the Command ArmTm for
easier operation. Valve can easily be re-programmed
from the operator’s seat for different implements or
variable conditions. Information on valve status is
displayed on the LCD display, located on the center
dashboard unit.
E-SCVs
The E-SCV field installation kit contains in addition to
the E-SCV parts as well the needed actuating
components for installation in the operator’s station.
Code
Bundle
AL169971
Description
Kit fo parts for E-SCV’s at
position III or IV
Models: cab only: 6320 - 6920S
Note: only for tractors with CommandArm
Note: If SCV will be installed on Position III please
order separately:
Bundle
AL169957
AL161388
Description
Remark
QTY
if on Pos III or IV
has not yet been
Right hand End Cover
installed a
1
and connecting parts
M-SCV Series
300/301 or an
E-SCV
for tractors from
Spacer (Power Beyond) serial number
with adjustable LS-bleed 398656 without 1
ICV’s
Issue 03-2008 (EAME)
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
6020 Series Tractors-19
2.4 MISCELLANEOUS
Additional oil reservoir 14 litres
Additional oil reservoir 12,5 litres
An additional hydraulic oil tank is available to increase
the hydraulic oil capacity with 12,5 litres (from 25 to
37,5 litres max. permissible oil withdrawal for short
term use (e.g. tipping trailers), while allowing the
tractor to run on inclines up to 18 degrees). This
reservoir mounts above the main hydraulic pump,
under the cab.
For applications which need more than 12,5 litres
additional hydraulic oil, John Deere offers a hydraulic
oil reservoir with 14 litres to increase the withdrawal
capacity of your hydraulic system.
Code
Bundle
8897
AL163978
Description
Hydraulic oil reservoir - 14 litres, with
quick connector system
Models: cab only: 6120 - 6420S
Note: for tractors with ICV order in addition
Bundle
L158929
Description
Protection hose
Remark
QTY
1
Note: for tractors with AutoPowr transmission order
in addition
Bundle
19M8169
Description
Screw
Remark
QTY
2
Note: for tractors without AutoPowr transmission
order in addition
Bundle
19M8823
Code
Bundle
AL158981
Description
Screw
Remark
QTY
2
Description
Additional oil reservoir
Models: cab only: 6120 - 6620
Code
Bundle
AL163979
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Description
Hydraulic oil reservoir - 14 litres, with
quick connector system
Models: cab only: 6520 - 6620
Note: for tractors with ICV order in addition
Bundle
L158929
Code
Description
Protection hose
Bundle
AL163980
Remark
QTY
1
Description
Hydraulic oil reservoir - 14 litres, with
quick connector system
Models: cab only: 6820 - 6920S
6020 Series Tractors-20
Code
Bundle
AL172666
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Description
Additional hydraulic oil reservoir 14 litres, with quick connector system
Models: cab only: 6120 - 6620
Note: for tractors with air brakes please order in
addition:
Bundle
AL171461
AL171462
AL171460
19M7496
19M8049
24M7028
14M7274
Description
Line
Line
Holding clamp for
compresssed air tank
M12 cap screw
M10 cap screw
Washer
M10 hex nut
Remark
6120 - 6420
6520, 6620
QTY
1
1
1
2
2
2
2
Issue 03-2008 (EAME)
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
6020 Series Tractors-21
3 ENGINE
Bottom guard for fuel tanks
Recommended in adverse conditions, like scrub,
woodland or land reclamation.
Code Bundle
AL113689
Description
Base guard for fuel tank, 116 l
Models: without cab: 6020 - 6420
Note: Please order additionally needed mounting
parts according to the latest parts catalog.
Code
8875
Bundle
AL159939
Description
Base guard for fuel tank, 250 l
Models: 6820 - 6920S
Code
Bundle
AL163513
Description
Base guard for fuel tank, 325 l
Models: cab only: 6820 - 6920S
Fuel Preheater
Code Bundle
8875 AL118241
Description
Base guard for fuel tank, 207 l
Particularly important in the cold season, fuel
preheaters prevent fuel waxing and subsequent filter
blockage by automatically actuating a heater element
in the filter at low temperatures.
Models: cab only: 6520 - 6920, 6520SE, 6620SE
Code
Bundle
AL158520
Description
Fuel Preheater
Models: 6020 - 6920S, 6020SE - 6520SE
Code
Bundle
8875
AL156243
Description
Base guard for fuel tank
(160 l, 165 l, 185 l)
Models: 6020 - 6420S, 6020SE - 6420SE
Note: not for level 4 engine, i.e. not for Bosch VP44
injection pump
6020 Series Tractors-22
Code
Bundle
AL159374
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Issue 03-2008 (EAME)
Description
Fuel Preheater
Models: 6320 - 6920S
Note: for level 4 engine, i.e. for Bosch VP44 injection
pump
Code
Bundle
AL151508
Description
Coolant preheater, 230V
Models: cab only: 6120 - 6920S, 6020SE - 6520SE
Coolant heater
Plugs into 220-volt electric wall socket, the integrated
heater element warms the engine block to provide
easier starting even in the coldest weather.
Cold start package
Code
Bundle
AL158792
Description
Cold start package, 230V
Models: cab only: 6120 - 6920S, 6020SE - 6520SE
Note: with PowrQuad or AutoQuad transmission for
use in Sweden, Finland and Norway
Note: if the tractor is not already equipped with a
coolant preheater, please order in addition
1 x AL151508 coolant preheater, 230V
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Fuel pre filters
Provide higher water and dirt protection to the fuel
system of your tractor. Bad fuel quality requires best
filtration. For this purpose pre filters can provide extra
filtration. Therefore, John Deere offers several pre
filter kits which provide:
• pre filtration of dust and particles to support the
main fuel filter
• separation of water to protect the fuel injection
pump and engine
The pre filter kits are mounted additionally to the
ordinary fuel filter and are supplied with all mounting
and connecting parts. The fuel pre filters have the
same service interval as the fuel filter.
Code
Bundle
AL160215
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Description
AL159200
speed control rod
assembly
AL159201
speed control rod
assembly
AL159202
speed control rod
assembly
Remark
for 6020SE low profile,
6320SE low profile,
6420SE low profile,
with Lucas injection
pump (mech.)
for 6020 low profile,
6320 low profile,
6420 low profile without
cab with Lucas
injection pump (mech.)
6120SE low profile,
6220SE low profile with
Stanadyne injection
pump (mech.)
QTY
1
1
1
Bundle
Description
AL159197
speed control rod
assembly
speed control rod
assembly
speed control rod
assembly
Remark
for 6020, 6320-6420S,
6020SE, 6320SE,
6420SE with Lucas
injection pump (mech.)
for 6120, 6220,
6120SE, 6220SE, 6215
with Stanadyne
injection pump (mech.)
for 6120 low profile,
6220 low profile without
cab, with Stanadyne
injection pump (mech.)
Code
Bundle
AL160216
Description
Fuel pre filter
Models: 6520, 6520SE, 6515
Note: Depending on the options of the tractor,
additional spare parts may be required.
AL159199
Bundle
Description
Fuel pre filter
Models: 6020 - 6420S,
6020SE - 6420SE
AL159198
6020 Series Tractors-23
QTY
1
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Note: Depending on the options of the tractor,
additional spare parts may be required.
Bundle
AL159326
1
AL159327
1
Description
speed control rod
assembly
speed control rod
assembly
Remark
QTY
for Lucas injection
1
pump (mech.)
for Stanadyne injection 1
pump (mech.)
6020 Series Tractors-24
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Issue 03-2008 (EAME)
Water in Fuel Sensor
Code
Bundle
RE509677
Description
Wiring harness, water sensor, 12V
Models: 6320 - 6920S
Note: for 4 cylinder tractors with 4-Valve CommonRail
PowerTech engine from engine serial-no.
800.000 up to engine serial-no. 811.593
Code
Bundle
AL160217
Description
Fuel pre filter
Note: for 6 cylinder tractors with 4-Valve CommonRail
PowerTech engine from engine serial-no.
800.000 up to engine serial-no. 811.673
Models: cab only: 6320 - 6420S
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Note: with electronical fuel injection, level 4
Code
Bundle
AL160218
Description
Fuel pre filter
Models: cab only: 6620 - 6920S
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Note: with electronical fuel injection, level 4
Code
Bundle
RE519696
Description
Wiring harness, water sensor, 12V
Models: 6020 - 6220 (DE10 injection pump),
6320 - 6920S (CommonRail injection system),
6020SE - 6620SE (DE10 injection pump),
6215, 6515 (DE10 injection pump)
Note: for tractors with 2-Valve PowerTech engine
from engine serial-no. 800.000
Note: for 4 cylinder tractors with 4-Valve
CommonRail PowerTech engine from
engine serial-no. 811.594
Note: for 6 cylinder tractors with 4-Valve
CommonRail PowerTech engine from
engine serial-no. 811.674
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Protective panels
On tractors without cab the protective panel reduces
the heat flow coming from the side grill to the
operator’s station. The engine cooling performance is
not affected.
Code
Bundle
AL161912
Description
Air flow deflector - protective panel
Models: without cab: 6020 - 6420, 6215
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Code
Bundle
AL161913
Description
Air flow deflector - protective panel
Models: without cab: 6520, 6620, 6515
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
6020 Series Tractors-25
6020 Series Tractors-26
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Issue 03-2008 (EAME)
4 ELECTRICAL - ELECTRONICAL COMPONENTS
4.1 LIGHTS
Code
AL161122
Beltline Headlights H4
These adjustable head lamps are fitted left and right to
the beltline of the cab. The halogen-type H4 bulbs
provide excellent illumination to the front and are
strongly recommended if front mounted equipment is
to be used, especially e.g. for highway use when a
loader or front linkage mounted implements obscure
the beam of the normal head lamps.
Bundle
Description
2 beltline-mounted headlights H4,
for right hand traffic
Models: cab only: 6020SE - 6520SE
Code
Bundle
AL161125
Description
2 beltline-mounted headlights H4,
for left hand traffic
Models: cab only: 6020SE - 6520SE
Code
Bundle
9070
AL157097
Description
2 beltline-mounted headlights H4,
for right hand traffic
Models: cab only: 6120 - 6920S
Note:
not compatible with H3 working lights
beltline-mounted (code: 9071)
Code
Bundle
AL159314
Description
2 beltline-mounted headlights H4,
for left hand traffic
Models: cab only: 6120 - 6920S
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
6020 Series Tractors-27
Working lights H3 - Beltline-mounted
These adjustable lamps are fitted left and right to
beltline of the cab. Especially for normal off-road use
the halogen-type H3 bulbs provide excellent
illumination of a loader, front-mounted equipment or
soil and crops and to the side of the tractor.
Code
9071
Bundle
AL157099
Description
2 working lights H3 beltline-mounted
Code
Bundle
AL159352
Models: cab only: 6120 - 6920S
Note:
not compatible with H4 headlights beltlinemounted (code: 9070).
Models: 6020 - 6920S, 6020SE - 6620SE
Note:
Depending on the options of the tractor,
additional spare parts may be required.
Bundle
Description
AL155611
6020 - 6420 with lowRocker switch clearance operator’s station 1
Front corner work lights
For increased illumination of the front working area,
additional lamps are directed downward and outward
to light the area immediately inside and ahead of the
front wheels. This will help operators following a
plough furrow or drill marker furrow at night. The
lamps may be switched off for road travel.
Description
Front corner work lights
Remark
6020 - 6520 with open
operator’s station
QTY
6020SE - 6620SE with cab
AL114046
Rocker switch 6120 - 6920S with cab
1
6020 Series Tractors-28
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Issue 03-2008 (EAME)
Work lights open operator’s station
Code
Bundle
AL79915
Description
Work lights, at rear of 2-post ROPS
Models: without cab: 6020 - 6520
Code
Bundle
AL161618
Description
Two additional work lights, cab-roof
mounted, REAR
Models: cab only: 6120 - 6920S
Additional work lights cab-roof mounted
Note: if the tractor is equipped with wiring harness
AL159155 ( from tractor serial no. XXXXXX)
which provides two connections for work lights
on the cab roof , order in addition wiring
harness AL156254 which provides the needed
four connections to install the work lights
Code
Bundle
AL161895
Description
Two additional work lights, cab roof
mounted, FRONT
Models: cab only: 6020SE - 6620SE
Code
Bundle
AL161617
Description
Two additional work lights, cab-roof
mounted, FRONT
Models: cab only: 6120 - 6920S
Note: if the tractor is equipped with wiring harness
AL159155 ( from tractor serial no. XXXXXX)
which provides two connections for work lights
on the cab roof , order in addition wiring
harness AL156254 which provides the needed
four connections to install the work lights
Code
Bundle
AL161897
Description
One additional work light, cab roof
mounted, REAR
Models: cab only: 6020SE - 6620SE
Xenon rear work lights
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Xenon headlights are firmly established within the
automobile industry, for giving the driver increased
visibility.
Xenon lights offer more advantages when used in the
field and John Deere gives the operator the opportunity
to use them to their fullest potential.
Advantages:
• 2.5 times the light flux (illuminance) of a halogen
Free Form working light.
Code
Bundle
AL172073
Description
Xenon working lights, rear
Models: cab only: 6120 - 6920S
6020 Series Tractors-29
6020 Series Tractors-30
ATTACHMENTS - FACTORY AND FIELD INSTALLED
4.2 MISCELLANEOUS
Issue 03-2008 (EAME)
Battery cut-off switch (4 cyl.)
Multiple power outlet socket
Code
9146
Bundle
AL158785
Description
Multiple power outlet socket
Code
Bundle
AL171054
Description
Battery cut-off switch
Models: cab only: 6120 - 6920S
Models: 6120 - 6420S, 6020SE - 6420SE
Note: Depending on the options of the tractor,
additional spare parts may be required.
Note:
Bundle
AL155784
AL117211
Description
Bracket (with CommandArm)
Bracket (without CommandArm)
QTY
1
1
order in addition adapter wiring harness
AL166461 for SE models up to tractor serial
number 413917
Note: Depending on the options of the tractor,
additional spare parts may be required.
Bundle
AL153812
3-terminal power outlet socket
AL159445
Description
QTY
Battery-negative cable / 1.500 mm
length (up to motor serial-no. 799.999) 1
Battery-negative cable / 1.500 mm
length (from motor serial-no. 800.000) 1
The 3-pin socket provides both 5 and 25 amp supplies
from the first two pins. The third pin is connected to
earth.
Battery cut-off switch (6 cyl.)
Code
Bundle
AL171055
Description
Battery cut-off switch
Models: 6520 - 6920S, 6520SE, 6620SE
Note:
order in addition adapter wiring harness
AL166461 for SE models up to tractor serial
number 413917
Note: Depending on the options of the tractor,
additional spare parts may be required.
Code
Bundle
AL160799
Description
3-terminal power outlet socket
Bundle
AL153812
Models: cab only: 6120 - 6920S, 6020SE - 6620SE
AL159445
Description
QTY
Battery-negative cable / 1.500 mm
length (up to motor serial-no. 799.999) 1
Battery-negative cable / 1.500 mm
length (from motor serial-no. 800.000) 1
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Back-up alarm
For customers who require an alarm in reverse speed.
It is rear mounted.
Code
Bundle
AL158728
Description
Field installation kit for back-up alarm
Models: 6120 - 6920S, 6020SE - 6620SE
Note: for tractors with SyncroPlus or PowrQuad
transmission
Code
Bundle
AL164284
Description
Field installation kit for back-up alarm
Models: 6320 - 6920S
Note: for tractors with AutoPowr transmission
6020 Series Tractors-31
6020 Series Tractors-32
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Issue 03-2008 (EAME)
5 MISCELLANEOUS
5.1 OPERATOR´S STATION
New Cab Accessories
John Deere offers new accessories for the highest in
operator comfort and convenience! Personalize your
tractor cab and underline the high-quality appearance
of your tractor with the following new accessories.
Leather cushions with seat heating
The dark brown leather seat cushion kit includes seat
and backrest cushions as well as a backrest extension.
The new leather trims provide the ultimate in operator
comfort; especially the extra thick seat cushion and the
backrest extension help to reduce operator fatigue for
more productivity even on long working days. In
addition, the integrated seat heating provides optimum
comfort on cold winter days.
Leather steering wheel
The new dark-brown leather steering wheel is elegant
in appearance and provides a comfortable grip even
during long working days!
It is produced in the high-standard John Deere quality
and features the same adjustability as the standard
steering wheel.
As an additional eye-catcher the name John Deere is
embroidered on the backrest extension.
The robust and longevity leather is easy to clean and
abrasion-proof.
Code
Bundle
AL173828
Description
Dark brown leather steering wheel
Models: 6120 - 6920S, 6020SE - 6620SE
Code
Bundle
AL174350
Description
Dark brown leather cushions and
backrest with preparation for seat
heating for MSG95 seats
Models: cab only: 6120 - 6920S, 6020SE - 6620SE
Note: Leather seat cushion is only compatible with
MSG95 seats with adjustable seat cushion
inclination and seat pan depth adjustment
(see picture below).
Note: For seats without seat heating please order in
addition AL151005 wiring harness and
AL151010 switch.
Stainless steel heat protection
for exhaust pipe
For an individual and elegant look John Deere offers
the new stainless steel heat protection for the exhaust
pipe.
It is produced in the high-standard John Deere quality
which ensures durability and a long service life.
Issue 03-2008 (EAME)
Code
Bundle
AL178133
ATTACHMENTS - FACTORY AND FIELD INSTALLED
6020 Series Tractors-33
Description
Stainless steel heat protection
for exhaust pipe
Models: 6120 - 6420S, 6020SE - 6420SE
Code
Code
Bundle
AL175376
Description
Stainless steel heat protection
for exhaust pipe
Models: 6520 - 6920S, 6520SE, 6620SE
Wood-look trims
Personalize your tractor cab with the new wood-look
trims. The kit includes decorative covers for the radio
console as well as the rear and front part of the
headlining - one with preparation for sunshade.
The new interior parts are easy to install and give your
John Deere tractor an elegant and extraordinary look!
Bundle
AL174268
Description
Wood-look trims
Models: cab only: 6120 - 6920S
6020 Series Tractors-34
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Issue 03-2008 (EAME)
Super Comfort seat - MSG85
The low frequency suspension technology now
absorbs shocks as low as 1.2 Hz and offers superior
back protection and driving comfort.
Mechanical seats features:
• Mechanical seat suspension
• Horizontal adjustment 210 mm
• 100 mm vertical suspension travel
• Backrest inclination
• Mechanical weight and height adjustment (80 mm)
• Mechanical lumbar support
• Horizontal suspension (-22 mm/+27 mm)
• Lateral suspension (+/-25 mm)
• Seat pan depth adjustment
• Seat cushion inclination
• Active carbon layer
• Fold down armrest
• +/-10° armrest inclination
• Operators manual holder
• 15° Swivel
In the past the driver had to select a hard suspension to
avoid bottoming of the seat when it reaches the lower
limit.
Code Bundle
Seating
Seats are ergonomically designed and covered in
stylish, easy to clean cloth upholstery.
Active Carbon Layer
An active carbon layer is used in the seat, to allow it to
breathe. This results in less sweating and further
increases the comfort of the operator.
Low Frequency Suspension
With the low frequency seat a soft setting of the
suspension is possible without the risk of hitting the
upper or lower limit.
This is achieved with an increased air volume and low
friction bearings.
AL164161
Models: cab only: 6120 - 6920S, 6020SE - 6620SE
Note:
order in addition seat belt AL117366 and
shield right hand side L114944 and shield left
hand side L114945
Code
Bundle
No additional shock absorber is required.
The system is designed according to suit the hydraulic
cab suspension frequency of 1.0 Hz and the TLS II.
The result is a floating but firm and sure feeling for the
driver for relaxed driving and better health.
Description
Super Comfort seat MSG85,
mechanical suspended
AL164159
Description
Super Comfort seat MSG85,
mechanical suspended;
seat cover yellow, vinyl
Models: all open operator’s station models
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
6020 Series Tractors-35
Super Air Comfort seat - MSG95
Code Bundle
AL154352
Description
Super Air Comfort seat MSG95,
air suspended , with seat switch
(without CommandArm)
Models: cab only: 6120 - 6920S, 6020SE - 6620SE
Note:
order in addition seat belt AL117366
Code Bundle
AL154354
Description
Super Air Comfort seat MSG95,
air suspended, with seat switch
(with CommandArm)
Models: cab only: 6320 - 6920S
Note:
for tractors equipped with AutoPowr;
order in addition seat belt AL155363
Super Comfort seat
Air suspended seat features:
• Air suspension with low frequency technology or
air suspension with high frequency suspension for
different suspension conditions
• Horizontal adjustment 210 mm for easy
positioning in the cab
• 100 mm vertical suspension travel to absorb even
the hardest shocks
• Backrest inclination
• Integrated telescopic backrest extension from 475645 mm for optimum back support
• Automatic weight and height adjustment (80 mm)
brings the ideal position for every body height
• Mechanical or pneumatic lumbar support
(pneumatic support allows a more quick and exact
adjustment of the lumbar support to prevent back
problems)
• Horizontal suspension (-22 mm/+27 mm) to damp
oscillations of implements, trailers at high speed or
in difficult terrain
• Lateral suspension (+/- 25mm) reliefs the driver
from side shocks
• Seat pan depth adjustment to optimize the support
of the legs
• Seat cushion inclination in 4 steps to relief
pressure from the knees
• Active carbon layer
• Seat heating
• Fold down armrest
• +/-10° armrest inclination
• Height adjustable armrest
• Operators manual holder
• Swivel +/-15° for easy access in and out of the seat
as well as easier control of rear implements
• Optional CommandArm
• Air suspension, low frequency
• Cushion cloth brown “Alaska” with carbon
• Foldable armrests with height and angle
adjustment
• Height adjustment 80 mm
• Horizontal adjustment 210 mm
• Backrest angle adjustment
• Fore and aft isolator
• Lateral horizontal isolator
• Lumbar support
• Weight adjustment
• Seat depth and angle adjustment
• Adjustable swivel +/- 180°
• Seat switch
• Seat heating
• Manual holder
• Seat belt
• Headrest
Code Bundle
AL157569
Description
Super Comfort seat MSG95
Models: cab only: 6120 - 6920S
6020 Series Tractors-36
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Issue 03-2008 (EAME)
Comfort seat - MSG83
•
•
•
•
•
•
•
•
•
Mechanical suspension
Horizontal adjustment 210 mm
Vertical suspension stroke 80 mm
Height adjustment 60 mm
Weight adjustment
Backrest angle adjustment
Foldaway armrests
Seat switch
Cushion vinyl yellow
Code Bundle
AL164156
Code Bundle
AL155363
Description
Seat belt
Models: cab only: 6020 - 6920S, 6020SE - 6520SE
Note:
for seat MSG 95 with CommandArm
Description
Comfort seat MSG83
Models: without cab: 6020 - 6420
Note: if seat belt is required please
order in addition AL117283
•
•
•
•
•
•
•
•
•
•
•
•
Mechanical suspension
Horizontal suspension 45 mm
Horizontal adjustment 210 mm
Vertical suspension stroke 80 mm
Height adjustment 60 mm
Weight adjustment
Mechanical lumbar support
Backrest angle adjustment
adjustable swivel 20°
Foldaway armrests
Seat switch
Cushion vinyl yellow
Code Bundle
AL164158
Code Bundle
AL117254
Description
Seat belt
Models: without cab: 6020 - 6420
Note:
for seat MSG44
Description
Comfort seat MSG83
Models: without cab: 6020 - 6420
Note: if seat belt is required please
order in addition AL117283
External swivel
The seat can be swiveled 180 degrees which allows an
easy operation of rear mounted equipment.
Seat belt for Super Comfort seats
For operator’s safety, recommended for all cab
tractors.
Code Bundle
AL119292
Code Bundle
9240 AL117366
Description
Seat belt
Models: 6120 - 6920S
Note:
for seat MSG 85 and MSG 95 without
CommandArm
Description
External adapter, 180° swivel
Models: 6020 - 6920S, 6020SE - 6520SE
Note:
for AL164161 Super Comfort seats MSG85
and AL154352 Super Air Comfort seats
MSG95 without CommandArm
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Instructional seat
The comfortable, soft-moulded instructional seat,
complete with backrest, is located to the left of the
operator.
Due to the overall roominess of the cab, the
instructional seat has excellent access with plenty of
head and shoulder clearance along with large leg-room
area.
A grab handle on the “A” post and an additional grab
rail on the door will help the passenger to feel safe and
secure, even over rough terrain.
When not required, the seat can be simply folded
away.
Code Bundle
9230 AL114321
6020 Series Tractors-37
Instructional seat with Suspension
The instructional seat with suspension offers a high
level of ride comfort.
The shock absorbing suspensions is totally adjustable
for passenger weight.
Suspension for instructional seat
Allows easy conversion of an
instructional seat into a suspended one.
unsuspended
Description
Instructional seat (not suspended)
Models: cab only: 6120 - 6920S, 6020SE - 6520SE
Safety belt for instructional seat
Code Bundle
9231 AL114856
Description
Suspension for instructional seat
Models: cab only: 6120 - 6920S, 6020SE - 6520SE
Code Bundle
AL117734
Description
Safety belt for instructional seat
Models: cab only: 6120 - 6920S, 6020SE - 6520SE
6020 Series Tractors-38
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Inner rear view mirror
Issue 03-2008 (EAME)
External Mirrors
Large external mirrors provide increased traffic
awareness for improved road safety and aid trailer
reversing.
Telescopic rear view mirrors
Telescopic mirrors offer manually adjustable
telescopic arms with manually adjustable mirrors. The
mirror mounts are offset on the stem to allow for
further adjustment and better head clearance when
entering the cab.
Code Bundle
9205 AL175679
Description
Inner rear view mirror
Models: cab only: 6120 - 6920S
Internal rear view mirror
The additional rear view mirror is installed on the
right-hand side of the rear window (in direction of
travel). It provides an excellent view on swinging
drawbar and rear-end attachments.
Code Bundle
7704 AL80126
Description
Left hand telescopic rear view mirror
Models: cab only: 6120 - 6920S
Code Bundle
AL151224
Description
Additional inside rear view mirror,
rear installation
Models: cab only: 6120 - 6920S
Code Bundle
7705 AL80127
Description
Right hand telescopic rear view mirror
Models: cab only: 6120 - 6920S
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Electrical, telescopic and heated
external mirrors
You can keep track of your daily work in a much more
convenient and comfortable way. The electrically
adjustable mirrors allow one man to set and adjust an
exact positioning of the external mirrors while
checking the view without leaving the driver’s seat.
The mirrors feature electrically adjustable telescopic
arms, electrically adjustable mirror heads as well as
heating to remove condensation and frost.
Code Bundle
AL157751
6020 Series Tractors-39
Rear windscreen wiper
Large rear windscreen wipers, with intermittent
switching, maintain good vision in bad weather.
Micro-switches are used to isolate wiper motors
when the windscreens are open.
Description
Electrical, telescopic and heated
external mirrors
Models: cab only: 6120 - 6920S
Front license plate
If the original number plate on the engine hood is
concealed by front-mounted implements, a new license
plate may be attached to the rear-view mirror on the
right hand side.
Code Bundle
9100 AL157191
Description
Rear windscreen wiper
Models: cab only: 6120 - 6920S
Code Bundle
AL162357
Description
Installation of front license plate
mount on tractors with front-mounted
implements
Models: cab only: 6120 - 6920S, 6020SE - 6620SE
Code Bundle
AL153672
Description
Rear window wiper and
washer system
Models: cab only: 6020SE - 6620SE
6020 Series Tractors-40
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Issue 03-2008 (EAME)
Rear windshield washer
Radio antenna in inner cab roof
The reservoir for the rear windshield washer is
installed under the right-hand step. It can be reached
easily, allows quick refilling.
For installation on the left-hand side of the inner cab
roof (viewed in direction of travel).
Code Bundle
AL173267
Description
Radio antenna in inner cab roof
Models: cab only: 6020 - 6920S, 6020SE - 6620SE
Performance monitor
Code Bundle
AL158767
Description
Rear windshield washer
Models: cab only: 6120 - 6920S
Water deflectors for the rear window
Code
Bundle
AL162899
Description
Water deflectors for the rear window
Models: cab only: 6120 - 6920S
The performance monitor is available for all 6020
Series tractors.
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
It can be installed on the upper right "A" post in the
cab and is connected directly to the tractor's electrical
system via the on-board CAN-BUS communication
link. This dedicated system allows the monitor to be
integrated with other tractor systems.
The unit features:
• Accurate "distance travelled" measurement *
• Display of true forward speed **
• Programmable implement width function allows
accurate measurement of area covered *
• Measurement and display of wheel-slip %, both
numerically and graphically, combined with visual
and audible slip alarm. **
• This helps to boost productivity and reduce tyre
wear *
• Work-rate calculation in area/unit time - a useful
management tool to optimise work-rates.
• "Implement-up" and "Implement-down" mode
linked to the quick raise/lower switch so that the
headland travel distance is not counted when
accurate area measurement is required.
• Display of precise rear and front PTO speeds for
accurate monitoring of implement performance.
• Programmable service indicator allowing the
operator to select the number of engine hours to
the next service.
• An audible and visual signal indicates when
this time has elapsed.
• This allows optimum service intervals for
peak tractor performance.
• Variable illumination intensity ensuring that the
operator can read the monitor easily, even at night.
The accuracy of the points marked * will be greatly
enhanced if the performance monitor is used in
conjunction with a John Deere radar unit.
The points marked with ** can only be displayed in
conjunction with the John Deere radar unit.
Code
9135
Bundle
AL156832
Description
Performance monitor
Models: cab only: 6120 - 6920S
6020 Series Tractors-41
Dual Beam Radar Sensor
Make sure your wheel slip is optimal - between 8% to
12% for tractors with MFWD and 10% to 15% for
tractors with two-wheel drive. Monitor your wheel slip
accurately with a dual beam radar sensor - save fuel,
avoid soil compaction, increase your tractive
performance, improve your efficiency.
Benefits of NEW dual beam design:
• Assures a powerful and accurate signal - Dual
beam output makes radar less susceptible to hard
surface tall/wavy grass interferences.
• Accuracy is aided by a heavy-gauge mounting
bracket and rubber isolators that reduce chances
that vibration can effect the radio signal.
• Has a fast update rate - when the tractor comes to
stop, accelerates or varies speed indicated ground
speed on the tractor display will closely match the
actual ground speed.
• Dual beam radar sensors are self-calibrating, no
setup time is needed anymore.
The radar sensor may be installed only on tractors
equipped with a Basic Control Unit (BCU).
Code
Bundle
RE243242
Description
Ground speed radar sensor unit
for Europe only
Models: 6120 - 6920S
Note: please order in addition AL171547 field
installation kit with mounting parts
Code
Bundle
RE218823
Description
Ground speed radar sensor unit
for UK and Ireland only
Models: 6120 - 6920S
Note: please order in addition AL171547 field
installation kit with mounting parts
6020 Series Tractors-42
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Issue 03-2008 (EAME)
Field office
Code
Bundle
RE243241
Description
Ground speed radar sensor unit
for Australia only
Models: 6120 - 6920S
Note: please order in addition AL171547 field
installation kit with mounting parts
Code
Bundle
AL171547
Description
Field installation kit with mounting
parts for ground speed radar sensor
Models: 6120 - 6920S
The field office for the 6020 Series tractors is a large
portfolio pouch where papers, operator manuals, music
cassettes, personal notes and implements information,
or even a laptop computer can be stored.
The entire unit is removable to be carried like a brief
case.
Its base is also pre-wired to accommodate electronic
devices like mobile telephones, or laptop computers.
The lid provides a flat writing surface.
Code Bundle
9220 AL157091
Description
Field office without beverage holder
Models: cab only: 6120 - 6920S
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
6020 Series Tractors-43
Sunshade front or rear
The John Deere pull-down sunshade improve
operator’s comfort on sunny days by blocking direct
light and reducing glare. In addition, they eliminate
heat build-up in the cab. Due to an independent
vertical adjustment the shades can be lowered and
raised to any desired position - for highest operator’s
comfort. This kit can be mounted to the front or rear
window and include all needed hardware for field
conversion - for an easy and convenient installation.
Code Bundle
AL174359
Code Bundle
AL157090
Description
Field office with beverage holder
Models: cab only: 6120 - 6420
Description
Sunshade front or rear
Models: cab only: 6120 - 6920S
Code Bundle
AL175264
Description
Sunshade front or rear
Models: cab only: 6020SE - 6620SE
Beverage cooler
Sun visor
Specifically designed for the operator’s station the
beverage cooler can be securely stored and easily
removed. Especially on hot days the operator will
appreciate the insulating capacity keeping food and
drinks cool.
Fold down sun visor to keep that low level sun out of
the operator’s eyes, from dawn to dusk.
Code Bundle
AL157620
Description
Sun visor installation
Models: cab only: 6120 - 6920S
Code Bundle
9215
AL112070
Description
Cool box (incl. fastening straps,
bracket and hardware)
Models: cab only: 6120 - 6920S
6020 Series Tractors-44
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Bottle holder
Issue 03-2008 (EAME)
Foot throttle
John Deere offers a new bottle holder for convenient
and safe storage of bottles in 6020 Series cabs. Rugged
plastic provides the accustomed John Deere quality.
The bottle holder is installed underneath the operator’s
seat in the corner between the step in the floor and the
console.
Code Bundle
9216 AL156731
Description
Bottle holder, left hand
Models: cab only: 6120 - 6920S
Code Bundle
AL153668
Note:
Models: 6215, 6515
not in combination with suspended
instructional seat
Cup-holder
Code Bundle
9218 AL163826
Description
Cup-holder on front right post
Models: cab only: 6120 - 6920S
Note: the cup-holder cannot be installed on tractors
equipped with a cool box
Description
Foot throttle
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Floor-mat
6020 Series Tractors-45
Ashtray
The ashtray is offered with hinged lid and made of
non-flammable materials. The design conforms to the
requirements of the accustomed John Deere design.
The installation is easy because the ashtray fits to the
existing recess.
Code
Bundle
AL168015
Description
Rear floor-mat
Models: cab only: 6120 - 6920S
Note: from tractor serial no. 398656, floor-mat
L156599 requires alteration on its underside
Code
Bundle
AL164673
Description
Ashtray
Models: cab only: 6120 - 6920S, 6020SE - 6620SE
Note: from tractor serial no. 357393
Cigarette lighter
The lighter is conforming to the accustomed John
Deere Design and is supplied with socket and
clamping sleeve. The power supply is provided by the
regular 12V power system of your John Deere tractor.
Code
Bundle
AL173370
Description
Cigar lighter
Models: cab only: 6120 - 6920S, 6020SE - 6620SE
Note: from tractor serial no. 357393
6020 Series Tractors-46
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Issue 03-2008 (EAME)
Chock Block
Code
Code
Bundle
LG102426
Description
Chock Block
Models: 6215
Models: 6120 - 6920S, 6020SE - 6620SE
Note: Depending on the options of the tractor,
additional spare parts may be required.
Bundle
Description
Remark
QTY
for installation on
the left hand side 1
for installation on
the right hand side 1
AL156154 Bracket
AL167955 Bracket
Right hand step kits
The large, non-slip footsteps feature a quick, surefooted entry. Footsteps are also designed to shed mud
and debris from operator’s shoes.
Code
8866
Bundle
AL115672
Bundle
AL116924
Description
Step kit, right hand
Models: without cab: 6520, 6515
Description
Step kit, right hand
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
6020 Series Tractors-47
Multi-function control lever for M-ICV
A mechanically operated multi-function lever may be
fitted to the front corner of the right hand console in
the cab to control M-ICV. The lever is useful for front
hitch control. The integrated design of the lever
ensures that operations have a natural feel which soon
become second nature.
Code
Bundle
AL116589
Description
Joystick for M-ICV control
Code
Bundle
AL164948
Description
Joystick for M-ICV control (floormounted)
Models: for open operators station low profile:
6020 - 6920S, 6020SE - 6620SE
Models: cab only: 6120 - 6920S, 6020SE - 6520SE
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Note: not for low profile
Note: from tractor serial number 398656
Note: up to tractor serial number 398655
Code
Bundle
AL164949
Description
Joystick for M-ICV control (floormounted)
Models: cab only: 6020 - 6920S,
6020SE - 6620SE (not with low profile cab,
not for tractors with CommandArm)
Note: from tractor serial number 398656
Code
Bundle
AL164951
Code
Bundle
AL164947
Description
Joystick for M-ICV control (floormounted)
Models: for open operators station: 6020 - 6920S,
6020SE - 6620SE
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Note: from tractor serial number 398656
Description
Joystick for M-ICV control (floormounted); lever with additional
switches for 3 diverter valves
Models: cab only: 6020 - 6920S,
6020SE - 6620SE (not with low profile cab,
not for tractors with CommandArm)
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Note: from tractor serial number 398656
6020 Series Tractors-48
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Issue 03-2008 (EAME)
Joysticks for E-ICV control
Code
Bundle
AL164953
Description
Joystick for M-ICV control (floormounted); lever with additional
switches for 3 diverter valves and gear
shifiting
Models: cab only: 6020 - 6920S,
6020SE - 6620SE (not with low profile cab,
not for tractors with CommandArm)
Note: for tractors with AutoQuad Plus or PowrQuad
Plus transmission
Note: from tractor serial number 398656
Code
Bundle
AL164950
Description
Joystick for M-ICV control (floormounted)
Models: cab only: 6020SE - 6420SE
(with low profile cab)
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Note: from tractor serial number 398656
Code
Bundle
AL164952
Description
Joystick for M-ICV control (floormounted); lever with additional
switches for 3 diverter valves
Models: cab only: 6020SE - 6420SE
(with low profile cab)
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Note: from tractor serial number 398656
The shape and size of the Single Lever Control
corresponds to the anatomy of the operator's hand. It
features two push buttons and one proportional control
toggle switch integrated in the grip to control up to 5
functions.
An integrated safety guard prevents unintentional
implement operation. Lever functions are only
transmitted, if the guard is tilted away by the gripping
hand. A toggle switch at the base of the lever allows
function to be disengaged when not in use, e.g. field
work, transport etc.
For optimum forearm ergonomics, lever position can
be adjusted through movement of its base in the
horizontal plane. To permit free entry/access via the
right-hand side door, it can further be swivelled
downwards - out of the way.
The maximum number of double acting control
valves in combination with Single Lever Control
increases to six.
Code
Bundle
AL159344
Description
Joystick for E-ICV control without
CommandArm
Models: cab only: 6120 - 6920S
Note: From tractor serial number 398656 and
depending on the options of the tractor,
additional spare parts may be required (see table
below).
Note: If diverter valves (for 4th and 5th function) are
applied, order additionally 1 x DC51685 (wiring
harness).
Bundle
Description
AL164526
Wiring harness
Remark
6120 - 6920S without
CommandArm
QTY
1
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Bundle
Description
AL157528
Wiring harness
AL157527
Wiring harness
Remark
QTY
6120 - 6620 without
CommandArm; not for 1
tractors with TLS-axle
6820 - 6920S without
CommandArm; not for 1
tractors with TLS-axle
6020 Series Tractors-49
2-Post roll guard
Code Bundle
AL119439
Description
2-Post roll guard
Models: without cab: 6020 - 6520, 6215, 6515
Code
Bundle
AL159345
Description
Joystick for E-ICV control with
CommandArm
Models: cab only: 6320 - 6920S
Note: From tractor serial number 398656 and
depending on the options of the tractor,
additional spare parts may be required (see table
below).
Note: If diverter valves (for 4th and 5th function) are
applied, order additionally 1 x DC51685 (wiring
harness).
Bundle
Description
AL164525
Wiring harness
Remark
QTY
6320 - 6920S with 1
CommandArm
Air conditioning system
The 6020 air conditioning system is powerful enough
to keep a comfortable in-cab temperature, whatever the
outside conditions are. The air conditioning system
uses ozone-friendly R134A refrigerant.
6020 Series Tractors-50
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Bundle
Issue 03-2008 (EAME)
Description
AL160537 Refrigerant hose
AL162467 R134A receiver-drier
AL163559 R134A receiver-drier
AL179933 Refrigerant hose
Code
Bundle
AL157956
Remark
Evaporator to
compressor, suction
side, with Stage II
engine to 97/68/EC,
without air-brakes
Up to tractor serial
no. 398790
From tractor serial
no. 398791
Receiver-drier to
evaporator, from
tractor serial no.
398791
QTY
1
1
1
2
Description
Air conditioning system, 4 cyl.
Models: cab only: 6120 - 6420S
Note: Depending on the options of the tractor,
additional spare parts may be required.
Bundle
Description
AL161500 Refrigerant hose
AL157596 Deflexion roll
drive belt,
L111601
2475 mm length
L114293 drive belt,
2525 mm length
L167673 Console, air conditioning
compressor
L153258
Coolant hose,
top of cooler
L154872
Coolant hose
R128661
Pulley for fan
AL112101 Refrigerant hose
AL158320 Refrigerant hose
AL158321 Refrigerant hose
AL173843 Refrigerant hose
Remark
without air-brakes
QTY
1
1
without air-brakes
1
with air-brakes
1
without air-brakes
1
without air-brakes;
without engine Stage
II to 97/68/EC
without air-brakes;
with engine Stage II
to 97/68/EC
without air-brakes
Receiver-drier to
evaporator, up to
tractor serial no.
398790
Evaporator to
compressor, suction
side, with air-brakes
Evaporator to
compressor, suction
side, without airbrakes
Evaporator to
compressor, suction
side, with Stage II
engine to 97/68/EC,
with air-brakes
Code
1
Bundle
AL157957
Description
Air conditioning system, 6 cyl.
Models: cab only: 6520 - 6920S
1
1
1
Note: Depending on the options of the tractor,
additional spare parts may be required.
Bundle
Description
AL161500 Refrigerant hose
AL157596 Deflexion roll
1
L111600
L111601
1
L114293
L114468
1
L167673
Drive belt,
2460 mm length
Drive belt,
2475 mm length
Drive belt,
2525 mm length
Drive belt,
2515 mm length
Console, air-conditioning
compressor
Remark
6520 - 6920S
without air-brakes
6620 without airbrakes
6520 without airbrakes
QTY
1
1
1
1
6520 with air-brakes 1
6620 with air-brakes 1
6520 - 6920S
without air-brakes
1
Issue 03-2008 (EAME)
Bundle
Description
Drive belt,
L153282
2505 mm length
L155538 Drive belt,
2455 mm length
R128659* Pulley for fan
R128660* Pulley for fan
AL112102 Refrigerant hose
AL160831 Refrigerant hose
AL160830 Refrigerant hose
AL162467 R134A receiver-drier
AL163559 R134A receiver-drier
AL179933 Refrigerant hose
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Remark
6820 - 6920S with
air-brakes
6820 - 6920S
without air-brakes
6820 - 6920S
6620
Receiver-drier to
evaporator, up to
tractor serial no.
398790
Evaporator to
compressor, suction
side, without airbrakes; 6820 6920S
Evaporator to
compressor, suction
side, with air-brakes;
6820 - 6920S
Up to tractor serial
no. 398790
From tractor serial
no. 398791
Receiver-drier to
evaporator, from
tractor serial no.
398791
QTY
1
1
1
1
1
1
1
1
1
2
* Existing pulley needs to be replaced when the
diameter is different.
6020 Series Tractors-51
6020 Series Tractors-52
ATTACHMENTS - FACTORY AND FIELD INSTALLED
5.2 WEIGHTS
Please note that the weights displayed in this catalogue
are available through EPDC (DNS-System/JDPoint).
Front base weights
Quick-tatch weights
Code Bundle
AL71258
AL176563
Description
Front weight support, 60 kg
(for max. 14 quick-tatch weights)
Models: 6020 - 6520, 6020SE - 6520SE, 6215, 6515
Note: not compatible with front PTO
Code Bundle
8770
AL176564
Description
Front weight support, 70 kg
(for max. 14 quick-tatch weights)
Models: 6220
Note: not compatible with front PTO
Description
Set of 20 quick-tatch weights, 50 kg
each
Models: 6020 - 6920S, 6020SE - 6520SE, 6215, 6515
Note:
Code Bundle
Issue 03-2008 (EAME)
includes 10 x 50 kg left (L38449)
and 10 x 50 kg right (L38450)
Front weight stop kit
The attachment kit includes two special coupling
weights weighing 50 kg each that can be used within a
front weight package to create a trailer coupling. The
total kit weighs 100 kg.
Code Bundle
AL119964
Description
Front weight stop kit, 2 x 50 kg
Models: 6020 - 6920S, 6020SE - 6520SE, 6215, 6515
Mounting kits
For 8 - 18 quick-tatch weights
Note: if tractor is equipped with a 551 Series front
loader only this front weight support can be
installed (as it is dimensionally smaller than
AL176563 front weight support, 60 kg)
Code Bundle
8771
AL176565
Description
Front weight support, 110 kg
(for max. 18 quick-tatch weights)
Models: 6320 - 6920S
Note: not compatible with front PTO
Code Bundle
AL119967
Description
Mounting parts for 6, 8, 10 quick-tatch
weights
Models: 6020 - 6920S, 6020SE - 6520SE, 6215, 6515
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
6020 Series Tractors-53
Pick up weight - 900 kg
Fits on all 6020 Series base weights and Cat. II/III rear
3-point hitch or front hitch.
Code Bundle
AL119968
Description
Mounting parts for 12 & 14 quick-tatch
weights
Models: 6120 - 6920S, 6120SE - 6520SE, 6515
Code Bundle
9508 AL112166
Description
Pick up weight, 900 kg
Models: 6320 - 6920S
Code Bundle
AL82932
Description
Mounting parts for 16 & 18 quick-tatch
weights
Note:
for tractors with MFWD only, cannot be
installed in combination with front weights.
Models: cab only: 6320 - 6920S
Center link bracket
Required, if pick-up weight is used on the rear or front
3-point hitch. Includes two spacer bushings, if 400 kg
centre pick-up weight section only is used in the 3point hitch.
Code Bundle
9515
AL113121
Models: 6320 - 6920S
Description
Center link bracket for pick up weight
(with distance tubes)
6020 Series Tractors-54
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Horicon weight Package
Issue 03-2008 (EAME)
Front shields
8 x 20 kg front weights with 20 kg carrier attached to
the front of frame behind 50 kg type front weights.
Code Bundle
9500 AL160627
Description
Horicon weight package, 180 kg
Models: cab only: 6120 - 6920S
Note:
install only with 110 kg base weight
Code Bundle
AL157298
Description
Front shield
Models: 6520 - 6920S, 6520SE, 6515
Code Bundle
AL71269
Description
2 x 20 kg front weight for
Horicon weight package
Code Bundle
AL157299
Description
Front shield
Models: 6020 - 6420S, 6020SE - 6420SE, 6215
Models: cab only: 6120 - 6920S
Note:
install only with 110 kg base weight
REAR WHEEL WEIGHTS
Rear wheel weight - 38,5 kg
For steel wheels 28” and bigger on flanges.
Code Bundle
9520
AL119955
Description
Rear wheel weight set, 77 kg
(2 x 38,5 kg)
Models: 6020 - 6920S, 6020SE - 6520SE, 6215, 6515
Note:
Includes first set of parts bolted to the rim
(base mounting parts).
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Code Bundle
AL176898
6020 Series Tractors-55
Description
Rear wheel weight set on palette,
(20 x 55 kg)
Models: 6020 - 6920S, 6020SE - 6520SE, 6215, 6515
Code Bundle
AR56632
Description
Rear wheel weight set, 77 kg
(2 x 38,5 kg)
Models: 6020 - 6920S, 6020SE - 6520SE, 6215, 6515
Note:
Includes additional set of parts (if base
mounting parts included in AL119955 are
installed).
Rear wheel weight - 55 kg
For steel wheels 34” - 38” on flange axles.
Code Bundle
9525
AR56636
Description
Rear wheel weight set, 110 kg
(2 x 55 kg)
Models: 6020 - 6920S, 6020SE - 6520SE, 6215, 6515
Note:
Includes first set of parts bolted to the rim
(base mounting parts).
Code Bundle
AL119956
Description
Rear wheel weight set, 110 kg
(2 x 55 kg)
Models: 6020 - 6920S, 6020SE - 6520SE, 6215, 6515
Note:
Includes additional set of parts (if base
mounting parts included in AR56636 are
installed).
Note:
Please order in addition mounting parts
according to parts catalog.
Note:
for steel wheels 34’’ - 38’’ on flange axles
6020 Series Tractors-56
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Issue 03-2008 (EAME)
5.3 CHASSIS PARTS
Code Bundle
8841
Front fenders
For safer high speed road transport and reduced tractor
soiling. Large, full-coverage flexible front fenders
with wide range of adjustments to adapt to the
different tread settings to protect the cab from mud and
debris.
AL180099
Description
MFWD rigid front fenders,
480 mm width
Models: 6020 - 6620, 6020SE - 6620SE,
6215, 6515
Code Bundle
8841
AL180101
Description
MFWD rigid front fenders,
540 mm width
Models: 6020 - 6620, 6020SE - 6620SE,
6215, 6515
Code Bundle
8841
AL180103
Description
MFWD rigid front fenders,
620 mm width
Models: 6020 - 6620, 6020SE - 6620SE,
6215, 6515
Front fenders for 2WD tractors
Code Bundle
8840 AL180215
Description
2WD front fenders
Models: 6020 - 6620, 6020SE - 6620SE,
6215, 6515
Base mounting kit for 4WD front fenders
Supporting parts and hardware required if respective
front fender field kits are ordered.
Front fenders for 4WD tractors
Code Bundle
8841
AL180095
Description
MFWD rigid front fenders,
370 mm width
Models: 6020 - 6620, 6020SE - 6620SE,
6215, 6515
Code Bundle
8841
AL180097
Description
MFWD rigid front fenders,
420 mm width
Models: 6020 - 6620, 6020SE - 6620SE,
6215, 6515
Code Bundle
AL71218
Description
Base mounting kit for MFWD front
fender
Models: 6020 - 6920S, 6020SE - 6520SE, 6215, 6515
Issue 03-2008 (EAME)
Code Bundle
8841 AL71215
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Description
MFWD front fender, 310 mm width
Code Bundle
8841 AL158554
6020 Series Tractors-57
Description
MFWD front fender, 410 mm width
Models: 6020 - 6420, 6020SE - 6320SE
Models: 6820 - 6920S
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Note: Order additionally: AL71218 mounting kit
For tire sizes:
• 14.9-28
• 380/85R28
For tire sizes:
• 9.5-24, 10.5-18, 11.2-24, 275/80R18
Code Bundle
8841 AL71216
Description
MFWD front fender, 355 mm width
Models: 6020 - 6820, 6020SE - 6520SE, 6215
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Note: Order additionally: AL71218 mounting kit
For tire sizes :
• 11.2-28, 12.4-24, 12.4-28, 12.5-20, 335/80R20
Code Bundle
8841 AL111669
Description
MFWD front fender, 470 mm width
Models: 6120 - 6420S, 6220SE - 6420SE
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
For tire sizes:
• 14.9-26
• 16.9-24
• 420/70R24
• 480/65R24
Code Bundle
8841 AL159607
Code Bundle
8841 AL159606
Description
MFWD front fender, 410 mm width
Models: 6020 - 6920S, 6020SE - 6520SE, 6215, 6515
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
For tire sizes:
• 13.6-24
• 13.6-28
• 14.5-20
• 14.9-20
• 14.9-24
• 14.9LR20
• 360/70R24
• 375/75R20
• 380/70R24
• 380/70R28
Description
MFWD front fender, 470 mm width
Models: cab only: 6520 - 6920S
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
For tire sizes:
• 16.9R24
• 16.9R26
• 16.9R28
• 420/70R24
• 420/70R28
6020 Series Tractors-58
Code Bundle
8841 AL158552
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Description
MFWD front fender, 470 mm width
Code Bundle
8841 AL158553
Issue 03-2008 (EAME)
Description
MFWD front fender, 520 mm width
Models: 6820 - 6920S
Models: 6820 - 6920S
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
For tire sizes:
• 16.9-28
• 420/70R28
• 420/85R28
For tire sizes:
• 16.9-30
• 480/65R28
• 480/70R28
• 480/70R30
• 480/85R30
• 540/65R28
• 540/65R30
Conversion from rigid front fenders to
turnable front fenders
Code Bundle
AL175211
Code Bundle
8841 AL70278
Description
MFWD front fender, 520 mm width
Models: 6320 - 6420S
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
For tire sizes:
• 480/65R24
• 480/65R28
• 540/65R24
Code Bundle
8841 AL159608
Description
MFWD front fender, 520 mm width
Description
Conversion kit from rigid front
fenders to turnable front fender
Models: 6120 - 6920S
Note: only for front fenders with single arm support
from tractor serial no. XXXXXX
Note: Depending on the options of the tractor,
additional spare parts may be required.
Bundle
Description
L173579
Strap
L173580
Strap
L165857
Strap
L170462
Strap
L158118
Bumper
Special hex head
screw M6X25
Models: 6520 - 6920S
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
For tire sizes:
• 18.4R26
• 480/65R24
• 480/70R24
• 480/70R26
• 480/70R28
• 540/65R24
• 540/65R26
• 540/65R28
37M7199
AL165335 Fender stop panel
AL165336 Fender stop panel
Remark
for tractors with
front fenders of
370, 420 and 480
mm width
for tractors with
front fenders of 540
and 620 mm width
for tractors with
front fenders of
355, 410 and 470
mm width
for tractors with
front fenders of 520
mm width
QTY
2
2
2
2
2
2
for 4 cyl. tractors
with front loader
application
for 6 cyl. tractors
with front loader
aplication
1
1
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
6020 Series Tractors-59
Turnable front fenders
A single arm fender for MFWD axles offers a greater
steering angle. It stops at the frame and turns while the
tires move further until the maximum steering angle is
reached. The turning circle now is the same as on
tractors without fenders.
Code Bundle
8842 AL180098
Description
Turnable front fender, 420 mm width
Models: 6020 - 6920S, 6020SE - 6620SE, 6215, 6515
Note: for front loader application an additional fender
stop panel AL165335 (4 cyl. tractors) or
AL165336 (6 cyl. tractors) has to be ordered
separately
Note: not for APL 2060
For tire sizes:
• 14.9R20
• 14.9R24
• 14.9R28
• 16.9R24
• 16.9R28
• 16.9R30
• 375/70R20
• 380/70R24
• 380/70R28
• 380/85R24
• 380/85R28
• 380/85R30
• 420/65R24
• 420/70R24
• 420/70R28
• 420/85R24
• 420/85R28
• 420/85R30
Code Bundle
8842 AL180100
8842
AL180096
Turnable front fender, 370 mm width
Models: 6020 - 6620, 6020SE - 6620SE
Note: for front loader application an additional fender
stop panel AL165335 (4 cyl. tractors) or
AL165336 (6 cyl. tractors) has to be ordered
separately
For tire sizes:
• 11.2R20
• 11.2R24
• 11.2R28
• 12.4R24
• 12.4R28
• 13.6R24
• 13.6R28
• 280/70R16
• 280/85R24
• 280/85R28
• 320/70R24
• 320/85R24
• 320/85R28
• 340/85R24
• 340/85R28
• 360/70R24
Description
Turnable front fender, 480 mm width
Models: 6020 - 6920S, 6020SE - 6620SE, 6215, 6515
Note: for front loader application an additional fender
stop panel AL165335 (4 cyl. tractors) or
AL165336 (6 cyl. tractors) has to be ordered
separately
Note: not for APL 2060
For tire sizes:
• 440/65R24
• 480/65R24
• 480/65R28
• 480/70R24
• 480/70R28
• 480/70R30
6020 Series Tractors-60
Code Bundle
8842 AL180102
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Description
Turnable front fender, 540 mm width
Code
Models: 6020 - 6920S, 6020SE - 6620SE
Note: for front loader application an additional fender
stop panel AL165335 (4 cyl. tractors) or
AL165336 (6 cyl. tractors) has to be ordered
separately
Note: not for APL 2060
For tire sizes:
• 520/60R28
• 540/65R24
• 540/65R28
• 540/65R30
• 540/75R28
Code Bundle
8842 AL180104
Bundle
AL120094
AL174767
Issue 03-2008 (EAME)
Description
Mounting parts for fender extension
Fender extension, 110 x 15 mm
Models: 6020SE - 6420SE
For tire sizes:
• 13.6R38
• 16.9R34
• 18.4R30
• 480/70R34
Code
Description
Turnable front fender, 620 mm width
Bundle
AL120094
AL174767
L116670
L116671
Models: 6020 - 6920S, 6020SE - 6620SE
Models: 6320 - 6420S
Note: for front loader application an additional fender
stop panel AL165335 (4 cyl. tractors) or
AL165336 (6 cyl. tractors) has to be ordered
separately
For tire sizes:
• 18.4R38
Description
Mounting parts for fender extension
Fender extension, 110 x 15 mm
Splash guard LH
Splash guard RH
Note: not for APL 2060
For tire sizes:
• 600/60R28
• 600/60R30
• 600/65R28
Fender side extensions
Code
Bundle
AL120094
AL174767
L116672
L116673
Description
Mounting parts for fender extension
Fender extension, 110 x 15 mm
Splash guard LH
Splash guard RH
Models: with suspended cab: 6820 - 6920S
For tire sizes:
• 460/85R38
• 18.4-38
Code Bundle
AL120094
L156328
L156329
L116670
L116671
Description
Mounting parts for fender extension
Fender extension, LH, 110 x 60 mm
Fender extension, RH, 110 x 60 mm
Splash guard LH
Splash guard RH
The fender extensions are a one piece design.
Models: 6120 - 6420, 6020SE - 6420SE
They are compatible for use with snow chains on the
rear wheels, for example for forestry applications.
Cover large tires and significantly reduce soiling of
tractor and cab.
For tire sizes:
• 13.6R38, 14.9R38, 16.9R34, 480/70R34, 18.4R34
(6120, 6220, 6020SE - 6420SE)
• 16.9R38
(6220 - 6420)
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
• 18.4R34
(6320)
• 14.9R38, 480/70R38
(6320, 6420)
• 18.4R30
(6020SE - 6220SE)
• 480/70R38, 16.9R38
(6220SE - 6420SE)
Code
Bundle
AL120094
AL174769
L116672
L116673
6020 Series Tractors-61
Description
Mounting parts for fender extension
Fender extension, 190 x 20 mm
Splash guard LH
Splash guard RH
Models: 6520 - 6920S with suspended cab
Code
Bundle
AL120094
L156328
L156329
Description
Mounting parts for fender extension
Fender extension, LH, 110 x 60 mm
Fender extension, RH, 110 x 60 mm
For tire sizes:
• 20.8R38
• 520/85R38
• 580/70R38
• 650/65R38
Models: 6020SE - 6220SE
For tire sizes:
• 16.9R30
Code
Bundle
AL120094
L156328
L156329
L116672
L116673
Code
Description
Mounting parts for fender extension
Fender extension, LH, 110 x 60 mm
Fender extension, RH, 110 x 60 mm
Splash guard LH
Splash guard RH
Bundle
AL120094
L156332
L156333
L116670
L116671
Description
Mounting parts for fender extension
Fender extension, LH, 190 x 65 mm
Fender extension, RH, 190 x 65 mm
Splash guard LH
Splash guard RH
Models: 6120 - 6420, 6020SE - 6420SE
For tire sizes:
• 520/70R34 (6120 - 6420, 6020SE - 6420SE)
• 540/65R38 (6320, 6420)
Models: 6320 - 6420S with suspended cab,
6520 - 6920S
For tire sizes:
• 18.4R38
(6320 6420S with suspended cab)
• 16.9R38, 18.4R38, 480/70R38, 520/70R38,
420/85R38, 460/85R38, 540/65R38
(6520)
• 540/65R38
(6520 with suspended cab)
• 18.4R38, 460/85R38, 520/70R38
(6620)
• 18.4R38, 460/85R38
(6820, 6920S)
Code
Bundle
AL120094
L156332
L156333
L116672
L116673
Description
Mounting parts for fender extension
Fender extension, LH, 190 x 65 mm
Fender extension, RH, 190 x 65 mm
Splash guard LH
Splash guard RH
Models: 6320 - 6420S with suspended cab,
6520 - 6920S
For tire sizes:
Code Bundle
AL120094
AL174769
L116670
L116671
Models: 6320, 6420S
For tire sizes:
• 520/70R38
• 600/65R38
Description
Mounting parts for fender extension
Fender extension, 190 x 20 mm
Splash guard LH
Splash guard RH
• 520/70R38
(6320 - 6420S with suspended cab, 6520, 6620)
• 540/65R38 (6520)
• 600/65R38
(6320 - 6420S with suspended cab, 6520 - 6920S)
• 20.8R38, 520/85R38, 650/65R38
(6520 - 6920S)
6020 Series Tractors-62
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Fender extension
For heavy duty work and bad weather conditions John
Deer offers a mud flap kit for 6020 Series tractors. The
mud flap provides an additional protection to avoid
dirt on your tractor and following vehicles. It is made
of rugged and flexible rubber, that bears up against
worst application conditions. The kit fits to all 6020
Series tractors with a 190 mm width fender extensions.
Code
Bundle
AL159975
Description
Fender extension
Models: cab only: 6120 - 6920S, 6020SE - 6620SE
Note: can only be installed if the tractor already has a
190 x 65 mm or 190 x 20 mm side-extension on
its fenders.
Issue 03-2008 (EAME)
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
5.4 AXLES
6020 Series Tractors-63
Front axle
Extensions
Rear axle
Rear axle extensions are available to match different
tread settings.
Code
Bundle
AL156778
Description
Distance hub, 60mm, for centering the
front wheels
Models: 6020 - 6520, 6020SE - 6520SE, 6215, 6515
Code
Bundle
AL156776
Description
Distance hub, 30 mm, for rear axle
extension
Note: In combination with front wheels with bolt circle
measuring 275 mm in dia.
Note: Increased tread setting from 2016 mm-2134 mm
Models: 6020 - 6520, 6020SE - 6520SE, 6215, 6515
Tie-rod extension - front axle
Note: In combination with rear wheels with bolt circle
measuring 203 mm in dia.
For extension of the track width by 102 mm at each
side (left and right hand).
Note: Increased tread setting from 1912 mm-1976 mm
Code
Bundle
AL156779
Description
Distance hub, 44 mm, for rear axle
extension
Models: 6020 - 6520, 6020SE - 6520SE, 6215, 6515
Note: In combination with rear wheels with bolt circle
measuring 203 mm in dia.
Note: Increased tread setting from 1916 mm-2004 mm
Code
Bundle
AL156777
Description
Distance hub, 111mm, for rear axle,
treadadjusting
Models: 6020 - 6520, 6020SE - 6520SE, 6215, 6515
Note: for 6020 - 6220 order addionally:
1 x L116668 reinforcement ring
Note: Increased tread setting from 1912 mm-2138 mm
Code
Bundle
AL164291
Description
Tie rod extension, front axle
Models: 6215, 6515
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Note: with open operator’s station
6020 Series Tractors-64
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Issue 03-2008 (EAME)
Track extension front and rear axle
The extended track and extra-wide vehicle lighting are
intended only for 6-cylinder tractors with a 335 mm
(13.19 inch) hole-circle diameter on front wheels and
with a 275 mm (10.83 inch) hole-circle diameter on
rear wheels.
In order to work as efficient as possible, progress in
row planting and the use of wider attachments demand
flexible track widths. To meet these demands John
Deere offers track extensions for 6-cylinder tractor
models.
With the help of the extended track, it is possible to
cover more rows at once and to ride within the rows
without affecting cultivations or banks. For sprayer
applications the new field installation kits provide
another advantage: the extended track of the tractor
allows a superior support and balance adjustment of
the sprayer.
Two different extensions are available:
• Extension 2 x 94 mm provides a track extension
to 2000 mm. Depending on the overall tractor
width, additional lighting kits for extra-wide
vehicles are available.
• Extension 2 x 219 mm provides a track extension
to 2250 mm. Depending on the overall tractor
width, additional lighting kits for extra-wide
vehicles are available.
Code
Bundle
AL162738
Description
Track extended to 2000 mm
(78.74 inch)
Models: 6520 - 6920S (cab only), 6620SE
Note: Maximum overall width of 2550 mm (100.4 inch)
Note: For maximum overall width of 2550 - 2750 mm
(100.4 - 108.3 inch) extra-wide vehicle lighting
is needed, please order in addition 1 x AL169786
Note: Must NOT be installed on tractors with dual
wheels
Note: Important when extending the track of the rear
axle and rear wheels are attached by studs and
wheel nuts: length of studs has to be 120 mm
(4.72 inch) and wheel nuts has to be M20 x 1.5.
If required, please order 16 x L150648 (stud)
and 16 x 14M7499 (wheel nut) separately.
Note: Important when extending the track of the rear
axle and rear wheels are attached by wheel
bolts: wheel bolts has to be M20 x 1.5 x 95 cap
screws. If required, please order 16 x L152520
(wheel bolt) separately.
Code
Bundle
AL179433
Description
Track extended to 2250 mm
(88.58 inch)
Models: 6520 - 6920S (cab only), 6620SE
Note: Maximum overall width of 2750 - 3000 mm
(108.3 - 118.11 inch)
Note: For maximum overall width of 2750 - 3000 mm
(108.3 - 118.11 inch) extra-wide vehicle lighting
and warning sign is needed, please order in
addition 1 x AL164386
Note: Must NOT be installed on tractors with dual
wheels
Note: Important when extending the track of the rear
axle and rear wheels are attached by studs and
wheel nuts: length of studs has to be 120 mm
(4.72 inch) and wheel nuts has to be M20 x 1.5.
If required, please order 16 x L150648 (stud)
and 16 x 14M7499 (wheel nut) separately.
Note: Important when extending the track of the rear
axle and rear wheels are attached by wheel
bolts: wheel bolts has to be M20 x 1.5 x 95 cap
screws. If required, please order 16 x L152520
(wheel bolt) separately.
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
6020 Series Tractors-65
Reinforcement of rear wheels
For heavy-duty operations in the field, the rear wheels
(on flanged rear axle with fine thread) can be reinforced with this kit.
Code
Bundle
AL155035
Description
Rear wheel reinforcement for heavy
duty operations in the field
Models: 6420 - 6920S
Note: On tractors not equipped with a second spacer
ring, follwing parts must be ordered in addition:
Bundle
L152520
24M7242
L150648
Code
Bundle
AL164386
Description
Extra-wide vehicle lighting and
warning sign
Models: 6520 - 6920S (cab only), 6620SE
Note: Maximum overall width of 2750 - 3000 mm
(108.3 - 118 inch)
Code
Bundle
AL169786
Description
Extra-wide vehicle lighting
Models: 6520 - 6920S (cab only), 6620SE
Note: Maximum overall width of 2750 mm (108.3 inch)
Description
M20 x 1.5 x 95 cap
screw
Remark
for tractors with 80 mm
long wheel bolts
for
tractors with 80 mm
Washer
long wheel bolts
tractors with 105 mm
M20 x 1.5 x 120 stud for
long studs
QTY
16
16
16
6020 Series Tractors-66
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Issue 03-2008 (EAME)
5.5 BRAKES AND STEERING
Bundle
Description
Remark
6320 - 6620 and
6320SE - 6620SE with
cab and MFWD;
Hydraulic trailer brake
Hydraulic trailer
AL165274 brake valve (I = 6)
6520, 6620 and
6520SE, 6620SE with
cab and no MFWD or
with 2-post ROPS
QTY
1
for UK;
6020 - 6220 and
6020SE - 6220SE;
The hydraulic trailer brake system gives a powerful,
safe braking function. The tractor brake-pedal operated
system gives a trailer braking function proportional to
the pressure applied to the pedal.
6320, 6420 and
Hydraulic trailer
AL165275 brake valve (I = 9.2) 6320SE, 6420SE with
cab and no MFWD or
with 2-post ROPS;
1
6320 - 6620 MFWD with
brake
The field kits below permit the tractor to be retro-fitted
with an hydraulic trailer brake.
Code
Bundle
AL174450
Description
Hydraulic trailer brake
Models: 6215, 6515
Code
9350
Bundle
AL172930
Description
Hydraulic trailer brake
Models: 6820 - 6920
Note: Depending on the options of the tractor,
additional spare parts may be required.
Bundle
Code
9350
Bundle
AL172929
Description
Hydraulic trailer brake
Models: 6020 - 6620, 6020SE - 6620SE
Note: Depending on the options of the tractor,
additional spare parts may be required.
Description
trailer
AL165274 Hydraulic
brake valve (I = 6)
trailer
AL165275 Hydraulic
brake valve (I = 9.2)
Remark
for UK;
with cab and MFWD
MFWD with brake for UK;
MFWD with brake
QTY
1
1
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
6020 Series Tractors-67
Pneumatic trailer brake
Code
Bundle
9356
AL157141
Description
Pneumatic trailer brake, dual-line
system
Models: cab only: 6120 - 6420S
Note: up to tractor serial no. 398655
Note: Depending on the options of the tractor,
additional spare parts may be required.
Bundle
Description
AL159976
AL151103
The pneumatic trailer brake system consists basically
of a two line system. This is the same as used today on
commercial vehicles.
Pre-braking function:
• short brake pedal travel allows braking of the
trailer without braking the tractor. This feature is
required to control the trailer and prevent jack
knifing.
• A quick release valve opens the trailer brake
immediately after release of the brake pedal for
better acceleration.
Single line systems for pneumatic trailer brakes are
available as well. These kits are supplementary to the
dual-line systems, they can not be used stand alone.
The dual-line system has to be installed first before the
single line system should be ordered.
The field kits below permit the tractor to be retro-fitted
with a pneumatic trailer brake system.
AL67648
L154523
L80375
R104558
14M7492
L156032
L114290
AL157596
L114293
L153010
AL161500
R113050
AL158320
P50883
Remark
without brakes on front
Trailer brake valve wheels
with brakes on front
Trailer brake valve
wheels
Pressure-limiting
with brakes on front
valve
wheels
with brakes on front
Elbow fitting
wheels
with brakes on front
Special ring
wheels
with brakes on front
O-ring
wheels
with brakes on front
Nut
wheels
with brakes on front
Elbow fitting
wheels
Poly-V-belt
(2385 mm length) without air-conditioning
Deflection roll
without air-conditioning
Poly-V-belt
(2525 mm length) with air-conditioning
Refrigerant hose
with air-conditioning
Refrigerant hose
with air-conditioning
O-ring
with air-conditioning
Refrigerant hose
with air-conditioning
O-ring
with air-conditioning
Code
Bundle
9356
AL157140
QTY
1
1
1
1
2
2
2
1
1
1
1
1
1
1
1
1
Description
Pneumatic trailer brake, dual-line
system
Models: cab only: 6520, 6620
Note: up to tractor serial no. 398655
Note: Depending on the options of the tractor,
additional spare parts may be required.
Bundle
Description
AL159976 Trailer brake valve
AL151103 Trailer brake valve
AL67648
Pressure-limiting
valve
Remark
without brakes on front
wheels
with brakes on front
wheels
with brakes on front
wheels
QTY
1
1
1
6020 Series Tractors-68
Bundle
Description
L154523
Elbow fitting
L80375
Special ring
R104558
O-ring
14M7492
Nut
L156032
Elbow fitting
Poly-V-belt
L114290
(2385 mm length)
AL157596 Deflection roll
Poly-V-belt
L114293
(2525 mm length)
AL161500 Refrigerant hose
R113050 O-ring
R33259
O-ring
L114670 O-ring
AL160830 Refrigerant hose
P50883
O-ring
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Issue 03-2008 (EAME)
Remark
with brakes on front
wheels
with brakes on front
wheels
with brakes on front
wheels
with brakes on front
wheels
with brakes on front
wheels
QTY
without air-conditioning
1
Note: Depending on the options of the tractor,
additional spare parts may be required.
without air-conditioning
1
Bundle
with air-conditioning
1
AL173363 Fuel tank (160 l)
with air-conditioning
with air-conditioning
with air-conditioning
with air-conditioning
with air-conditioning
with air-conditioning
1
1
1
1
1
1
L156143
AL79740
1
2
Code
Bundle
AL157144
Description
Pneumatic trailer brake, single-line system
Models: cab only: 6020 - 6620
2
Note: up to tractor serial no. 398655
2
Note: This single-line system can only be installed in
connection with dual-line system AL157140
and AL157141.
1
Code
9356
Description
Bracket
Bracket
Bundle
AL157142
Remark
6020 - 6420S if not
already equipped
with suspended cab
without suspended cab
QTY
1
1
1
Description
Pneumatic trailer brake, dual-line system
Models: cab only: 6820 - 6920S
Note: up to tractor serial no. 398655
Note: Depending on the options of the tractor,
additional spare parts may be required.
Bundle
L101379
AL154881
AL119370
AL119371
11M7058
14M7273
19M8008
24M7055
AL37332
AL151104
AL152869
AL151106
AL151107
AL159976
AL151103
AL67648
L154523
L80375
Description
Bracket
Pilot line
Linkage
Remark
without suspended cab
without suspended cab
without suspended cab
without suspended cab,
Linkage
but with AutoPowr
transmission
Cotter pin
with suspended cab
Nut (M8)
with suspended cab
Screw (M8x35 mm) with suspended cab
Washer
with suspended cab
Fitting
with suspended cab
Bracket
with suspended cab
Pilot line
with suspended cab
Linkage
with suspended cab
with suspended cab and
Linkage
AutoPowr transmission
Trailer brake valve without brakes on front
wheels
Trailer brake valve with brakes on front
wheels
Pressure-limiting
with brakes on front
valve
wheels
with brakes on front
Elbow fitting
wheels
with brakes on front
Special ring
wheels
QTY
1
1
1
1
1
2
2
3
1
1
1
1
1
1
1
1
1
2
Issue 03-2008 (EAME)
Bundle
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Remark
with brakes on front
R104558 O-ring
wheels
with brakes on front
14M7492 Nut
wheels
with brakes on front
L101118 Hose
wheels
with brakes on front
L154383 Bracket
wheels
with brakes on front
Z32994
Fitting
wheels
with brakes on front
L64164
Back-up ring
wheels
with brakes on front
L80372
Elbow fitting
wheels
with brakes on front
14M7273 Nut
wheels
with brakes on front
15M7054 Nut
wheels
19M7324 Screw (M8X75 mm) with brakes on front
wheels
L153281 Poly-V-belt
without air-conditioning
(2375 mm length)
L153282 Poly-V-belt
with air-conditioning
(2505 mm length)
AL161500 Refrigerant hose
with air-conditioning
R113050 O-ring
with air-conditioning
AL160830 Refrigerant hose
with air-conditioning
P50883
O-ring
with air-conditioning
Code
Description
Bundle
AL157145
QTY
2
1
2
2
1
AL161651
Description
Pneumatic trailer brake, dual-line
system
Models: 6020SE - 6620SE
Note: Depending on the options of the tractor,
additional spare parts may be required.
Bundle
Description
L155194
Shield
L114293
Drive belt
L114290
Drive belt
R128661
Belt pulley
1
2
2
1
1
1
1
1
1
Description
Pneumatic trailer brake, single-line
system
Note: This single-line system can only be installed in
connection with dual-line system AL157142.
Note: Depending on the options of the tractor,
additional spare parts may be required.
Remark
with suspended cab
without suspended cab
Bundle
Note: up to tractor serial no. 398655
1
Note: up to tractor serial no. 398655
Description
Bracket
Bracket
Code
2
Models: cab only: 6820 - 6920S
Bundle
L156143
AL79740
6020 Series Tractors-69
QTY
1
1
AL157596 Deflection roll
air
AL152714 Compressed
hose
air
AL152715 Compressed
hose
L153022 Air intake hose
L153344 Air intake hose
AL155089 Oil return line
AL116422 Oil return line
Remark
for 4 cyl. tractors with air
conditioning
for 4 cyl. and 6 cyl.
tractors with air
conditioning
for 4 cyl. and 6 cyl.
tractors without air
conditioning
for 4 cyl. and 6 cyl.
tractors without air
conditioning
for 4 cyl. and 6 cyl.
tractors without air
conditioning
QTY
for 4 cyl. tractors
1
for 6 cyl. tractors
1
for 4 cyl. tractors
for 6 cyl. tractors
for 4 cyl. tractors
for 6 cyl. tractors
for
tractors
AL161173 Refrigerant line
with air conditioning
1
1
1
1
1
1
1
1
1
1
6020 Series Tractors-70
Code
Bundle
AL164723
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Description
Pneumatic trailer brake, single-line
system
Code
Bundle
AL164977
Issue 03-2008 (EAME)
Description
Pneumatic trailer brake, dual-line
system with precharge valve
Models: cab only: 6120 - 6620, 6020SE - 6620SE
Models: cab only: 6820 - 6920S
Note: from tractor serial no. 398656
Note: from tractor serial no. 398656
Note: This single-line system can only be installed in
connection with dual-line system.
Note: Depending on the options of the tractor,
additional spare parts may be required.
Code
Bundle
AL164975
Description
Pneumatic trailer brake, single-line
system
Models: cab only: 6820 - 6920S
Note: from tractor serial no. 398656
Note: This single-line system can only be installed in
connection with dual-line system.
Code
Bundle
AL164976
Description
Pneumatic trailer brake, dual-line
system without precharge valve
Bundle
Description
AL157596 Deflection roll
Drive belt, 2375
L153281
mm (93.50 inch)
AL161500 Refrigerant hose
AL160830 Refrigerant hose
L153282 Drive belt, 2505
mm (98.63 inch)
24M7055 Washer
19M7513 Cap screw
L158770 Protective
edging
L113893 Screw
AL160421 Coupling end
(brake)
Coupling
end
AL160422
(supply)
Remark
without air-conditioning
QTY
1
without air-conditioning
1
with air-conditioning
with air-conditioning
1
1
with air-conditioning
1
1
1
1
2
for Great Britain only
1
for Great Britain only
1
Models: cab only: 6820 - 6920S
Note: from tractor serial no. 398656
Note: Depending on the options of the tractor,
additional spare parts may be required.
Bundle
Description
AL157596 Deflection roll
belt, 2375
L153281 Drive
mm (93.50 inch)
AL161500 Refrigerant hose
AL160830 Refrigerant hose
belt, 2505
L153282 Drive
mm (98.63 inch)
24M7055 Washer
L158770 Protective
edging
19M7513 Cap screw
Coupling end
AL160421 (brake)
Coupling end
AL160422 (supply)
Code
Bundle
AL164987
Description
Pneumatic trailer brake, dual-line
system without precharge valve
Remark
without air-conditioning
QTY
1
Models: cab only: 6520, 6620, 6520SE, 6620SE
without air-conditioning
1
Note: from tractor serial no. 398656
with air-conditioning
with air-conditioning
1
1
Note: Depending on the options of the tractor,
additional spare parts may be required.
with air-conditioning
1
Bundle
Description
AL157596 Deflection roll
L114290 Drive belt, 2385
mm (93.89 inch)
AL161500 Refrigerant hose
AL160830 Refrigerant hose
belt, 2525
L114293 Drive
mm (99.41 inch)
belt, 2515
L114468 Drive
mm (99.01 inch)
24M7055 Washer
19M7513 Cap screw
Coupling end
AL160421 (brake)
Coupling end
AL160422 (supply)
1
1
1
for Great Britain only
1
for Great Britain only
1
Remark
without air-conditioning
QTY
1
without air-conditioning
1
with air-conditioning
with air-conditioning
1
1
with air-conditioning
1
with air-conidtioning
1
1
1
for Great Britain only
1
for Great Britain only
1
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
6020 Series Tractors-71
Bundle
Code
Bundle
AL164988
Description
Pneumatic trailer brake, dual-line
system with precharge valve
Description
Coupling end
AL160421
(brake)
AL160422 Coupling end
(supply)
Remark
QTY
for Great Britain only
1
for Great Britain only
1
Models: cab only: 6520, 6620, 6520SE, 6620SE
Note: from tractor serial no. 398656
Note: Depending on the options of the tractor,
additional spare parts may be required.
Bundle
Description
AL157596 Deflection roll
Drive belt, 2385
L114290
mm (93.89 inch)
AL161500 Refrigerant hose
AL160830 Refrigerant hose
L114293 Drive belt, 2525
mm (99.41 inch)
L114468 Drive belt, 2515
mm (99.01 inch)
24M7055 Washer
19M7513 Cap screw
L113893 Screw
AL160421 Coupling end
(brake)
Coupling
end
AL160422
(supply)
Code
Bundle
AL164998
Remark
without air-conditioning
QTY
1
without air-conditioning
1
with air-conditioning
with air-conditioning
1
1
with air-conditioning
1
with air-conidtioning
1
1
1
2
for Great Britain only
1
for Great Britain only
1
Description
Pneumatic trailer brake, dual-line
system without precharge valve
Models: cab only: 6120 - 6420S, 6020SE - 6420SE
Note: from tractor serial no. 398656
Note: Depending on the options of the tractor,
additional spare parts may be required.
Bundle
Description
AL157596 Deflection roll
L114290 Drive belt, 2385
mm (93.89 inch)
R128661 Belt pulley
AL161500 Refrigerant hose
AL158320 Refrigerant hose
AL173843 Refrigerant hose
Drive belt, 2525
L114293 mm (99.41 inch)
L153010 Radiator hose
24M7055 Washer
19M7513 Cap screw
Remark
without air-conditioning
QTY
1
without air-conditioning
1
without air-conditioning
with air-conditioning
with air-conditioning
with air-conditioning
1
1
1
1
with air-conditioning
1
with air-conidtioning
1
1
1
Code
Bundle
AL164999
Description
Pneumatic trailer brake, dual-line
system with precharge valve
Models: cab only: 6120 - 6420S, 6020SE - 6420SE
Note: from tractor serial no. 398656
Note: Depending on the options of the tractor,
additional spare parts may be required.
Bundle
Description
AL157596 Deflection roll
L114290 Drive belt, 2385
mm (93.89 inch)
R128661 Belt pulley
AL161500 Refrigerant hose
AL158320 Refrigerant hose
AL173843 Refrigerant hose
Drive belt, 2525
L114293 mm (99.41 inch)
L153010 Radiator hose
24M7055 Washer
19M7513 Cap screw
L113893 Screw
end
AL160421 Coupling
(brake)
end
AL160422 Coupling
(supply)
Remark
without air-conditioning
QTY
1
without air-conditioning
1
without air-conditioning
with air-conditioning
with air-conditioning
with air-conditioning
1
1
1
1
with air-conditioning
1
with air-conidtioning
1
1
1
2
for Great Britain only
1
for Great Britain only
1
6020 Series Tractors-72
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Dampened Shock Valves
Issue 03-2008 (EAME)
Accumulator
Code
Bundle
AL169778
Description
Field kit accumulator with
mounting parts
Models: 6020 - 6920S
Note: only for tractors without hydraulic cab
suspension
Code
Bundle
AL169779
Description
Field kit accumulator with
mounting parts
Models: 6020 - 6920S
Code
Bundle
AL157038
Description
Field kit for attenuated shock valves in
the steering system
Models: 6820 - 6920S
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Note: up to tractor serial no. 358863
Note: only for tractors with hydraulic cab suspension
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
5.6 STORAGE
6020 Series Tractors-73
Additional storage container - 45l
Tool box
With a capacity of 45 l and a 45 kg maximum payload this
new sheet metal storage container offers additional space,
e.g. for rubber boots, oil cans, bulky tools, grease guns etc.
Equipped with 2 handles at the side it can easily be carried.
With the help of the included quick lock pin the container
can be closed rapidly.
The fastening on the back allows a quick installation to all
existing front weights: base weights, front weights and the
900 kg pick up weight.
An external detachable and lockable tool box with
convenient carrying handle is located in front of the
cab.
It has the capacity to hold tools and a selection of
linkage balls, hitch pins and linchpins for implement
attachment.
Code Bundle
8850
AL156255
Description
Sheet metal tool box, mounted to main
frame, right hand side
Models: cab only: 6120 - 6920S, 6020SE - 6420SE
Code Bundle
AL120005
Description
Storage container, 45 l
Models: 6020 - 6920S, 6020SE - 6620SE, 6215, 6515
Note:
45 kg maximal payload; only for front installation:
attachable to base weights, front weights and 900
kg pick up weight.
6020 Series Tractors-74
ATTACHMENTS - FACTORY AND FIELD INSTALLED
5.7 HITCHES AND ASSOCIATED
EQUIPMENT
Issue 03-2008 (EAME)
Remote control of trailer hitches
Tool bars
For light weight cat. II implements attached to the tool
bar, 3 different versions are available:
• Tool bar for links with ball ends
• Tool bar for links with hook ends
• Tool bar for links with hook ends - extended length
Code Bundle
9476
AL81951
Description
Tool bar for links with hook ends, cat. II
(standard)
Models: 6120 - 6920S, 6020 SE - 6420SE
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Note:
For hook-type, cat. II lower links, complete
with stabilizer bracket (without ball guides).
Code
Bundle
AL158725
Description
Remote control of height-adjustable
trailer hitches
Models: cab only: 6120 - 6420S
Release cables
For upper and lower link hooks including hardware
(screws, clamps, holder etc.)
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Code
Bundle
AL158726
Description
Remote control of rigid trailer hitches
Models: cab only: 6120 - 6420S
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Code Bundle
AL81619
Description
Cables for controlling the center link
and draft links
Models: 6120 - 6920S, 6020SE - 6420SE
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
6020 Series Tractors-75
Stabilizer bar “Economy”
Automatic stabilizer bars
For use only with cat. II and cat. III flat bar draft links.
These provide manual adjustment of lateral hitch
movement.
Automatic stabilzer bars offer for the respective
implements the possiblity to have:
• lateral sway over a self defined lower range and no
sway above, or
• no sway over the whole range
Code Bundle
AL176759
Description
Automatic stabilizer bars,
right hand and left hand
Models: 6120 - 6620
Code Bundle
AL117961
Description
Stabilizer bar “Economy”
Models: 6120 - 6620, 6020SE - 6520SE, 6215, 6515
Code Bundle
AL176760
Description
Automatic stabilizer bars,
right hand and left hand
Models: 6820 - 6920S
Code Bundle
AL151119
Description
Stabilizer bar “Economy”
Models: 6820 - 6920S
Stabilizer chains with sway control blocks
For almost universal implement control.
6020 Series Tractors-76
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Issue 03-2008 (EAME)
Swinging drawbar
Code Bundle
AL80849
Description
Stabilizer chains
Drawbars are adjustable in length and the swinging
feature can also be locked out.
Models: cab only: 6120 - 6620
Note: for tractors with telescopic lift link or flat steel
lift link order in addition:
Bundle
L79378
19M7489
19M7409
Description
Console for cat. II or cat. III
Screw M16x45 for cat. II
Screw M16x50 for cat. III
QTY
2
4
4
Code Bundle
9441 AL80054
Description
Swinging drawbar with hammer strap
Models: 6020 - 6620, 6020SE - 6520SE, 6215, 6515
Lock for draft link hooks
When implements with asymmetrical load are
attached, or when driving through high-growing
bushes and trees, the draft links must be secured
against opening accidentally.
Code Bundle
AL165485
Description
Lock for draft link hooks
Models: 6020 - 6920S, 6020SE - 6620SE
Code Bundle
9441
AL81349
Description
Swinging drawbar with hammer strap,
includes swinging drawbar L115073
Models: 6820 - 6920S
Note:
not used with Powrshift transmission
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
6020 Series Tractors-77
Hitch Holder for upper wagon hitch
Changing the implement from trailer to three-point
hitch in the field and not knowing where to put the
upper trailer hitch.
John Deere now offers the solution - the hitch holder
for the upper wagon hitch. The holder is a convenient
solution that can easily be mounted within minutes
onto all kinds of front weights with coupling recess.
The wagon hitch can easily be affixed and is stored in
a convenient height you can reach without stooping.
The holder is adjusted with two fixing screws that
again can be adjusted in two widths depending on the
weight the holder has been mounted onto.
Code Bundle
Description
Swinging drawbar,
includes swinging drawbar AL151017
AL119419
Models: 6820 - 6920S
Note:
used with Powrshift transmission
Guide Ball Holder
To store the guide balls for hook type 3 point hitch and
top link quick couplers just where they are needed.
Code
Bundle
AL165650
Description
Hitch holder for upper trailer hitch
Models: 6020 - 6920S, 6020SE - 6620SE
Code Bundle
9463 AL161925
Description
Guide Ball Holder
Models: 6020 - 6920S, 6020SE - 6620SE
Note: for all tractors without pneumatic trailer brake
Note: for tractors with pneumatic trailer brake from
tractor serial no. 398656
6020 Series Tractors-78
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Load control shaft, support
Code
Bundle
AL156675
Issue 03-2008 (EAME)
.
Description
Load control shaft support
Models: 6820 - 6920S
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Note: without receiving pins on main frame
Note: up to serial no. XXXXXX
Code Bundle
AL118022
Description
JD pick up hitch with hook
Models: 6020 - 6620, 6020SE - 6520SE
Code
Bundle
AL160835
Description
Load control shaft support
Note: order in addition:
1 x L112143 from tractor serial no. 192965
Models: 6820 - 6920S
Note: from serial no. XXXXXX
John Deere Pick Up Hitch
The John Deere Pick-up Hitch provides one-man
hitching with excellent visibility. The hitch can be
hydraulically adjusted in length and height for
coupling trailers or trailed implements, even under
difficult working conditions like uneven ground, very
low placed trailers, etc.
Two different coupling devices are available:
• hook type is in base
• drawbar can be ordered optional
Either of the two items can be stored in a frame
mounted universal holder
Code
Bundle
AL159072
Description
JD pick up hitch with hook
Models: 6820 - 6920S
Note: order in addition:
1 x L112143 from tractor serial no. 192965
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
6020 Series Tractors-79
Drawbar
Note: please order in addition:
Bundle
38H5015
AL163534
AL156366
L155798
L153588
Code
Code Bundle
9447
AL157346
Description
Drawbar with storage for
JD pick up hitch
Models: cab only: 6120 - 6920S, 6020SE - 6520SE
Description
Elbow fitting
Endplate
Shuttle valve
Console
Flanged screw
Bundle
AL164326
QTY
1
1
1
1
2
Description
Field kit for electro-hydraulic control of
pick-up hitch
Models: 6820 - 6920S
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Note: only for tractors with CommandArm
Electro-hydraulic control of pick-up hitch
Note: please order in addition:
Bundle
38H5015
AL163534
AL156366
AL156849
L156614
38H5215
Description
Elbow fitting
Endplate
Shuttle valve
Oil line
M10 special screw
T-fitting
Low position hitches
with 3-in-1 wagon hitch
Code
Bundle
AL164328
Description
Field kit for electro-hydraulic control of
pick-up hitch
Models: 6320 - 6620
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Note: only for tractors with CommandArm
Code
9419
Bundle
AL177172
Description
Rail with piton fix insert slider
Models: 6020 - 6920S, 6020SE - 6620SE
QTY
2
1
1
1
1
1
6020 Series Tractors-80
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Issue 03-2008 (EAME)
Low position wagon hitches
for 9-position rail
Code
Bundle
AL177174
Description
Piton fix insert slider
Models: 6020 - 6920S, 6020SE - 6620SE
Code
Bundle
AL176731
Description
Wagon hitch height-adjustable,
piton fix
Models: 6020 - 6920S, 6020SE - 6620SE
Note: for 9-position rail only
9405
AL177173
Rail with ball typ insert slider
Models: 6020 - 6920S, 6020SE - 6620SE
Code
Bundle
AL176726
Description
Wagon hitch height-adjustable,
ball
Models: 6020 - 6920S, 6020SE - 6620SE
Note: for 9-position rail only
Code
Bundle
AL177175
Description
Ball typ insert slider
Models: 6020 - 6920S, 6020SE - 6620SE
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Forced steering system
for wagon hitch height-adjustable
(ball type)
Code
Bundle
AL176727
Description
Forced steering system (two sides)
for wagon hitch height-adjustable,
ball type
6020 Series Tractors-81
Yoke for draft link support
Hinged to the left and right hand side rear axle, it
protects the draft sensor pins from shock loads under
extreme draft work.
Models: 6020 - 6920S, 6020SE - 6620SE
Code Bundle
AL78129
Models: 6320
Code
Bundle
AL176728
Description
Forced steering system (one side)
for wagon hitch height-adjustable,
ball type
Models: 6020 - 6920S, 6020SE - 6620SE
Forced steering system
for insert slider (ball type)
Code
Bundle
AL176729
Description
Forced steering system (two sides)
for ball typ insert slider
Models: 6020 - 6920S, 6020SE - 6620SE
Code
Bundle
AL176730
Description
Forced steering system (one side)
for ball typ insert slider
Models: 6020 - 6920S, 6020SE - 6620SE
Description
Yoke for draft link support
6020 Series Tractors-82
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Issue 03-2008 (EAME)
5.8 VANDALISM PROTECTION KITS
Code
Bundle
AL158988
Description
Vandalism protection
Models: 6520 - 6920S, 6520SE, 6515
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Security door lock kit
Locking the cab with an individual key, different from
the standard ignition key, is helpful for many different
applications of the tractor. John Deere therefore offers
the Security door lock field installation kit. It features
an individual key system that prevents misuse of the
standard ignition key. This field kit provides individual
security by individual keys for all equipment kept
inside the cab. The kit comes with four keys, in case of
damage or loss a blank key can be ordered.
Code
Bundle
AL110170
Description
Field kit, latch for oil filler neck,
transmission - vandalism protection
Models: 6020 - 6620, 6020SE - 6520SE, 6215, 6515
Code
Bundle
AL71345
Description
Security door lock kit
Models: cab only: 6120 - 6920S, 6020SE - 6620SE
Note: if needed please order in addition:
Code
Bundle
AL158987
Description
Vandalism protection
Models: 6020 - 6420S, 6020SE - 6420SE, 6215
Note: This Kit is no longer available, please order
individual parts according to parts catalog.
Bundle
AL71350
Description
Blank key
QTY
1
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Lockable fuel tank cap
Code
Bundle
AL113087
Description
Lockable fuel tank cap
Models: 6020 - 6920S, 6515, 6020SE - 6420SE,
6620SE
6020 Series Tractors-83
6020 Series Tractors-84
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Issue 03-2008 (EAME)
Numerical Index
Bundle No.
AL70278
AL71215
AL71216
AL71218
AL71258
AL71269
AL71345
AL77028
AL77680
AL78129
AL79915
AL80054
AL80126
AL80127
AL80849
AL81349
AL81619
AL81951
AL82290
AL82932
AL110170
AL111669
AL112070
AL112166
AL112428
AL113087
AL113121
AL113689
AL114321
AL114856
AL115672
AL116589
AL116924
AL117254
AL117366
AL117734
AL117838
AL117961
AL118022
AL118241
AL118486
AL119292
AL119419
AL119439
AL119955
AL119956
AL119964
Page
58
57
57
56
52
54
82
10
11
81
28
76
38
38
76
76
74
74
13
53
82
57
43
53
12
83
53
21
37
37
46
47
46
36
36
37
15
75
78
21
12
36
77
49
54
55
52
Bundle No.
AL119967
AL119968
AL120005
AL151119
AL151224
AL151508
AL153668
AL153672
AL154352
AL154354
AL155035
AL155363
AL156243
AL156255
AL156675
AL156731
AL156776
AL156777
AL156778
AL156779
AL156832
AL157038
AL157055
AL157090
AL157091
AL157097
AL157099
AL157140
AL157141
AL157142
AL157144
AL157145
AL157191
AL157233
AL157237
AL157238
AL157298
AL157299
AL157346
AL157569
AL157620
AL157751
AL157956
AL157957
AL158520
AL158552
AL158553
Page
52
53
73
75
38
22
44
39
35
35
65
36
21
73
78
44
63
63
63
63
41
72
2
43
42
26
27
67
67
68
68
69
39
2
4
4
54
54
79
35
43
39
50
50
21
58
58
Bundle No.
AL158554
AL158725
AL158726
AL158728
AL158767
AL158785
AL158792
AL158831
AL158981
AL158987
AL158988
AL159072
AL159273
AL159275
AL159296
AL159297
AL159314
AL159344
AL159345
AL159352
AL159374
AL159606
AL159607
AL159608
AL159939
AL159975
AL160215
AL160216
AL160217
AL160218
AL160414
AL160627
AL160799
AL160835
AL161122
AL161125
AL161617
AL161618
AL161651
AL161895
AL161897
AL161912
AL161913
AL161925
AL162171
AL162172
AL162357
Page
57
74
74
31
40
30
22
11
19
82
82
78
14
15
16
17
26
48
49
27
22
57
57
58
21
62
23
23
24
24
11
54
30
78
26
26
28
28
69
28
28
25
25
77
2
2
39
Bundle No.
AL162432
AL162433
AL162434
AL162450
AL162738
AL162899
AL163214
AL163513
AL163533
AL163534
AL163826
AL163978
AL163979
AL163980
AL164156
AL164158
AL164159
AL164161
AL164284
AL164291
AL164326
AL164328
AL164386
AL164673
AL164712
AL164723
AL164947
AL164948
AL164949
AL164950
AL164951
AL164952
AL164953
AL164975
AL164976
AL164977
AL164987
AL164988
AL164998
AL164999
AL165335
AL165336
AL165650
AL168015
AL169778
AL169779
AL169786
Page
3
1
3
16
64
40
4
21
10
10
44
19
19
19
36
36
34
34
31
63
79
79
65
45
16
70
47
47
47
48
47
48
48
70
70
70
70
70
70
70
59
59
77
45
72
72
65
Issue 03-2008 (EAME)
ATTACHMENTS - FACTORY AND FIELD INSTALLED
Numerical Index
Bundle No.
AL169787
AL169788
AL169789
AL169790
AL169791
AL169792
AL169965
AL169971
AL170031
AL171054
AL171055
AL171547
AL172073
AL172666
AL172929
AL172930
AL173267
AL173370
AL173828
AL174268
AL174350
AL174359
AL174450
AL174687
AL175211
AL175264
AL175376
AL175679
AL176563
AL176564
AL176565
AL176726
AL176727
Page
6
6
7
7
8
9
12
18
17
30
30
42
29
20
66
66
40
45
32
33
32
43
66
10
58
43
33
38
52
52
52
80
81
Bundle No.
AL176728
AL176729
AL176730
AL176731
AL176759
AL176760
AL176898
AL177172
AL177173
AL177174
AL177175
AL178133
AL179433
AL180095
AL180096
AL180097
AL180098
AL180099
AL180100
AL180101
AL180102
AL180103
AL180104
AL180215
AR56632
AR56636
EC300182
LG102426
RE218823
RE243241
RE243242
RE509677
RE519696
Page
81
81
81
80
75
75
55
79
80
80
80
33
64
56
59
56
59
56
59
56
60
56
60
56
55
55
13
46
41
42
41
24
24
6020 Series Tractors-85