Universal Ballasts
Basic-12
®
Basic Electronic Ballasts for T12 Lamp Applications
- Technology for Magnetic Ballast Replacements
- Exceeds Federal Ballast Efficiency Requirements
The Basic-12™ ballast family is designed for replacement of magnetic T12 ballasts during fixture maintenance or in combination with relamping programs to
reduce energy consumption. Basic-12™ ballasts provide electronic energy saving performance, generating energy savings of greater than 20% when replacing a magnetic ballasts while still using the same T12
lamps.
Basic-12™ ballasts fully comply with today’s new federal ballast efficiency requirements for installation into
new fixtures as well as with the 2010 requirements
for replacement ballasts. DOE compliant ballasts are
available for use with both standard and energy saving
lamps (Note: The B260I120M-A can only be used with
energy saving F96T12 lamps.)
The Basic-12™ product line covers the high volume requirements for T12 lighting:
Features
• Energy Efficient
- Greater than 20% Increase in Efficiency
- Lowers Lighting Operation Costs
• Full Light Output
- Provides Same Light Levels as Magnetic
Ballasts Being Replaced
• Quiet Operation
- Significantly Quieter than Magnetic Ballasts
• High Frequency Operation
- No Lamp Flickering
• Light Weight - Low Profile Case
- Simplifies Transportation & Installation
- Less Interference with Ballast Channel Cover
During Replacement
• Slimline Ballasts Feature Parallel Lamp Operation
- When One Lamp Fails, Other Lamp Remains Lit
• Same Warranty as Energy Saving Magnetic
T12 Ballasts
- Three-year Ballast Warranty
1-Lamp F34 & F40T12, 120V
2-Lamp F34 & F40T12, 120V
1 or 2 - Lamp F34 & F40T12, 277V
2-Lamp F96T12 & F96T12/ES, 120-277V
2-Lamp F96T12HO/ES, 120-277V
Replacement Comparison
F34/40T12 Rapid Start
1.7 lb Weight Reduction
Basic-12™ ballast is significantly smaller and
weighs less than the ballast it is replacing.
Basic-12™ ballast are ideal for replacing magnetic
ballasts in almost every application.
Universal Lighting Technologies, Inc. • 26 Century Blvd., Suite 500 • Nashville, TN 37214-3686 • (615) 316-5100 • www.universalballast.com
© 2007 Universal Lighting Technologies
Basic-12
®
Performance Savings
2xF34T12 Comparison
Ballast
2xF96T12/ES Comparison
Lamp
Input Power
Magnetic 2xF34T12
F34T12
74
B234SR120M-A
F34T12
59
Savings:
Ballast
Lamp
Input Power
Magnetic 2xF96T12/ES
F96T12/ES
133
B260IUNVHP
F96T12/ES
110
15 watts
Operating Savings
Savings:
23 watts
Operating Savings
Utility Rate ( $/KWH)
0.08
Utility Rate ( $/KWH)
0.08
Annual Operating Hours
3500
Annual Operating Hours
3500
Annual Savings:
$4.20
Replacement with Basic-12 rather than a standard magnetic saves
$4.20 per year in operating costs. With higher utility rates and longer
operating hours, savings will be even more.
• Rapid Start Basic-12 ballasts wire exactly the same way as their
magnetic counterparts
• Mounting dimensions are the same as the
magnetic ballasts
• Low profile case makes it easier to replace the
ballast channel without pinching wires.
Part Number
B134R120M-A 000I
B234SR120M-A 000I
B234SR277M-A 000I
B260I120M-A 000I * 0
B260IUNVHP 000I
B295SRUNVHP 000I
Annual Savings:
$6.44
Replacement with Basic-12 rather than a standard magnetic saves
$6.44 per year in operating costs. With higher utility rates and longer
operating hours, savings will be even more.
• Instant Start Basic-12 ballasts are wired slightly differently than
magnetic ballasts but easy to follow instructions are included.
• Parallel lamp operation keeps remaining lamp lit when one lamp
fails.
Lamp Application
(1) F34T12 or F40T12, 120V
(2) F34T12 or F40T12, 120V
(1) or (2) F34T12 or F40T12, 277V
(2) F96T12/ES, 120V
(2) F96T12 (Std & ES), 120-277V
(2) F96T12HO, 120-277V
Product Code
76838624257
76838624214
76838624367
76838624222
76838624224
76838624231
Basic-12 models are covered by a 36 month warranty. Visit www.universalballast.com for additional warranty information.
For use with energy savings lamps only (F96T12/WM,SS,EW)
B260I120M-A is shorter than standard magnetic ballast. A self-tapping screw may be required for mounting.
B12J0407
B234SR120M-A
APPLICATION and PERFORMANCE SPECIFICATION
Description: High frequency electronic ballast for (2) F40T12ES, (2) F40T12, (2) F32T12, or (2) F40T10 lamps
(and equivalent U-bend lamps)
• Line Voltage: 120vac , ±10%, 60Hz
• Series Lamp Operation
Lamps
Type
F40T12ES
F40T12
F32T12
F40T10
• Rapid Start
• Passive Power Factor Correction
Input
Nominal
Power
Ballast
Ballast Efficacy
Harmonic
Crest
#
Watts
Line Amps
Factor
Factor
Factor
Total
Factor
2
2
2
2
59
71
56
75
0.49
0.63
0.48
0.65
> .90
> .90
> .98
> .95
0.86
0.90
0.90
0.91
1.46
1.27
1.61
1.21
< 30%
< 30%
< 25%
< 30%
< 1.7
< 1.7
< 1.7
< 1.7
Application and Performance Specification Information Subject to Change without Notification.
Performance:
• Meets ANSI Standard C82.11-1993
• Meets ANSI Standard C62.41-1991
• Meets FCC Part 18 (Class B) for EMI and RFI
Consumer Limits
• Meets CSA Standard 654 for Ballast Efficiency
• Meets Energy Star® Requirements
Safety:
• No PCB's
• UL listed (Class P, Type 1 Outdoor, Type HL)
• CSA Certified
Application:
• Minimum Starting Temperature:
50° F, 10° C
Energy Saving Lamps:
60° F, 16° C
• Maximum Case Temperature:
167° F, 75° C
• Sound Rated:
A
• Remote Mounting:
20 ft. max. lead length, 18 AWG
Physical Parameters
Length:
9.50"
Width:
1.70"
Height:
1.18"
Weight:
1.70 lbs.
Lead Length: White, Black
Red, Blue
Yellow
22" (± 1")
26" (± 1")
45" (± 1")
Warranty:
Universal Lighting Technologies warrants to the purchaser that each electronic ballast will be free from
defects in material or workmanship for a period of 3 years from date of manufacture when properly installed
and under normal conditions of use. Call 1-800-BALLASTx800 for technical assistance.
Manufactured in China or North America
Blue
Blue
Red
Red
Black
Line
BALLAST
White
Yellow
Yellow
LAMP
LAMP
Ballast must be grounded in accordance with national and local electrical codes.
1-800-BALLAST
www.universalballast.com
November 2006
Specification Sheet
Catalog Number: S70MLTLC3M
Document #: 010-9651-07
Date: 06/28/2004
Lamp Type
ANSI Designation
Line Voltage
Regulation
Frequency
Recommended Fuse
Circuit Type
Insulation Class
Capacitor Value
Capacitor Volt Rating
Capacitor Temp Rating
Capacitor Part Number
Lamp Starter
Winding Material (Pri/Sec)
FEATURES:
Line
Volt
120
208
240
277
70W HIGH PRESSURE SODIUM
70W HPS
S62
120/208/240/277
5%
60 HZ
5/3/3/2
HX-HPF
180° C
7MF
300 VOLTS
90° C
005-1410-MF
HPS 150-3A
Al/Al
Replaces Catalog #
Samples Available
Production Available
Agency Certification
Maximum Distance to Lamp
12310-153
Yes
Yes
UL & CSA
10 FT
Utilizes Precise-Wound Coils
Electrical Characteristics
Open
Line Current in Amps
Power
Input
Circuit
Factor Oprtng
Open
Start
Watts
Volts
High
0.85
1.50
0.90
98
120
High
0.52
0.88
0.50
98
120
High
0.45
0.75
0.44
98
120
High
0.38
0.65
0.35
98
120
Drop
Out
Volts
90
155
180
208
Min.
Start
Temp.
-40°C
-40°C
-40°C
-40°C
UL
Temp.
Code
B
B
B
B
Reference Drawing
Line
Volt
120
208
240
277
Power
Factor
High
High
High
High
Test Limits
Line Current, Amps
Open Circuit
Operating
Open
Short
Voltage (V)
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
0.77
0.91
0.75
2.20
0.55
1.15
115
130
0.44
0.56
0.44
1.30
0.30
0.65
115
130
0.37
0.46
0.38
1.20
0.25
0.60
115
130
0.33
0.43
0.33
1.00
0.20
0.55
115
130
Physical Characteristics
Mounting Holes (In.)
Overall Dimensions, Inches
Length
3.94
Height
2.81
Stack
1.38
Over
Coils
2.74
Diam
0.25
Length
3.50
Width
2.44
Bracket
CapacitorDim.
Mntng Dim
Length Width Section Length
1.25
2.19
Application and Performance Specification Information Subject to Change without Notification.
For samples, contact your Universal Lighting Technologies Representative.
1-800-BALLAST
Short Circuit
Current (A)
Min.
Max.
1.55
2.80
1.55
2.80
1.55
2.80
1.55
2.80
www.universalballast.com
Ballast
Net
Weight
4.13
Lead
Length
Inches
12-14
S100MLTLC3M
100W
High Pressure Sodium
60Hz HX-HPF
Specification Sheet
120
Input Volts
Regulation
Line Volts
208
240
277
±5%
±5%
±5%
±5%
±5%
Lamp Watts
±10%
±10%
±10%
±10%
±10%
Power Factor (min)
90%
90%
90%
90%
90%
122 W
122 W
122 W
122 W
122 W
120 V
120 V
120 V
120 V
120 V
Input Watts
NOM. Open Circuit Voltage
Line Current (Amps)
Operating
1.12
S54
0.65
0.60
0.52
0
Open Circuit
2.20
1.30
1.10
0.95
0
Starting
0.80
0.55
0.41
0.35
0
Recommended Fuse (Amps)
7
5
3
3
0
Lamp Dropout Voltage (Line)
96 V
166 V
192 V
222 V
V
277V (BLACK)
LAMP
240V (VIOLET)
208V (ORANGE)
CAP (YEL)
STARTER
120V (BLK/YEL)
2
COM (YEL)
UL Temperature Ratings
Insulation Class
Temperature Code
MIN. Starting Temperature
(RED/BLK)
3
1
3
CAP (RED)
COM (YEL)
Wiring Diagram
H (180°C) H (180°C) H (180°C) H (180°C) H (180°C)
B
B
B
B
-40°F -40°C
-40°F -40°C
-40°F -40°C
-40°F -40°C
A
0.234 Dia Thru
4 Holes
B
MAX
-40°F -40°C
CAPACITOR Specifications
Microfarads
Volts (min.)
10 uf
10 uf
10 uf
10 uf
10 uf
280 V
280 V
280 V
280 V
280 V
60Hz Test Procedures
High Potential Test 1 Minute
2000 V
2000 V
2000 V
2000 V
2000 V
High Potential Test 1 Second
2500 V
2500 V
2500 V
2500 V
2500 V
Secondary Open Ckt Voltage (V)
110 - 130
110 - 130
110 - 130
110 - 130
110 - 130
Secondary Current Shorted (A)
2.60 - 3.20
2.60 - 3.20
2.60 - 3.20
2.60 - 3.20
2.60 - 3.20
Input Operating Current (A)
1.02 - 1.24
0.59 - 0.72
0.55 - 0.67
0.47 - 0.58
-
Input Open Circuit Current (A)
1.10 - 3.15
0.65 - 1.86
0.55 - 1.57
0.48 - 1.36
-
Input Short Circuit Current (A)
0.66 - 1.00
0.36 - 0.55
0.32 - 0.50
0.26 - 0.42
-
Temp Rating:
90 °C
Max Case Temp
105 °C
2.00 in
2.00 in
2.00 in
2.00 in
2.00 in
Height:
2.70 in
BTL:
10 ft
Dimension B
3.36 in
3.36 in
3.36 in
3.36 in
3.36 in
Width / Diameter:
2.16 in
Weight
6.00 lbs
6.00 lbs
6.00 lbs
6.00 lbs
6.00 lbs
12-14
12-14
12-14
12-14
12-14
Cu / Cu
Cu / Cu
Cu / Cu
Cu / Cu
Cu / Cu
Core and Coil Specifications
Dimension A
2.812"
0.250 Dia Thru
2 Holes
2.438"
3.500"
3.938"
Reference Drawing
Capacitor: 005-1413-MF
Ignitor: HPS150-3A
No. 1 (Red or Blue)
Lead Lengths (inches)
Coil Material (Pri. / Sec.):
No. 2 (Brown)
No. 3 (Yellow)
Document #:
010-9648-07
Date:
2/6/2007
Status:
Production
Replaces Catalog #:
12310-90
1.250"
2.000"
For alternate capacitor construction consult sales
Data is based upon tests performed by Universal Lighting Technologies in a controled environment and is representive of relative performance.
Actual performance may vary depending on operating conditions. Specifications are subject to change without notice.
2/2/2007
Universal Lighting Technologies
26 Century Blvd. Suite 500 - Nashville, TN 37214
Phone 1-800-225-5278 Fax 1-800-206-0035
www.universalballast.com
S150MLTLC3M
150W
High Pressure Sodium
60Hz HX-HPF
Specification Sheet
120
Input Volts
Regulation
Line Volts
208
240
277
±5%
±5%
±5%
±5%
±5%
Lamp Watts
±10%
±10%
±10%
±10%
±10%
Power Factor (min)
90%
90%
90%
90%
90%
188 W
188 W
188 W
188 W
188 W
120 V
120 V
120 V
120 V
120 V
Input Watts
NOM. Open Circuit Voltage
Line Current (Amps)
Operating
1.70
S55
0.95
0.85
0.70
277V (BLACK)
LAMP
240V (VIOLET)
208V (ORANGE)
CAP (YEL)
STARTER
120V (BLK/YEL)
2
Open Circuit
3.10
1.65
1.55
1.30
Starting
1.95
1.10
1.00
0.80
Recommended Fuse (Amps)
10
5
5
5
0
Lamp Dropout Voltage (Line)
96 V
165 V
192 V
220 V
V
COM (YEL)
UL Temperature Ratings
Insulation Class
Temperature Code
MIN. Starting Temperature
(RED/BLK)
3
1
3
CAP (RED)
COM (YEL)
Wiring Diagram
H (180°C) H (180°C) H (180°C) H (180°C) H (180°C)
B
A
B
A
-40°F -40°C
-40°F -40°C
-40°F -40°C
-40°F -40°C
A
0.234 Dia Thru
4 Holes
B
MAX
-40°F -40°C
CAPACITOR Specifications
Microfarads
Volts (min.)
14 uf
14 uf
14 uf
14 uf
14 uf
280 V
280 V
280 V
280 V
280 V
60Hz Test Procedures
High Potential Test 1 Minute
2000 V
2000 V
2000 V
2000 V
2000 V
High Potential Test 1 Second
2500 V
2500 V
2500 V
2500 V
2500 V
Secondary Open Ckt Voltage (V)
110 - 135
110 - 135
110 - 135
110 - 135
110 - 135
Secondary Current Shorted (A)
3.90 - 4.75
3.90 - 4.75
3.90 - 4.75
3.90 - 4.75
3.90 - 4.75
Input Operating Current (A)
1.50 - 1.90
0.80 - 1.00
0.75 - 0.95
0.60 - 0.80
-
Input Open Circuit Current (A)
1.55 - 4.40
0.85 - 2.40
0.80 - 2.20
0.65 - 1.85
-
Input Short Circuit Current (A)
1.20 - 1.85
0.65 - 1.00
0.60 - 0.95
0.50 - 0.80
-
Temp Rating:
90 °C
Max Case Temp
105 °C
2.50 in
2.50 in
2.50 in
2.50 in
2.50 in
Height:
2.69 in
BTL:
10 ft
Dimension B
3.85 in
3.85 in
3.85 in
3.85 in
3.85 in
Width / Diameter:
2.69 in
Weight
7.00 lbs
7.00 lbs
7.00 lbs
7.00 lbs
7.00 lbs
12-14
12-14
12-14
12-14
12-14
Cu / Al
Cu / Al
Cu / Al
Cu / Al
Cu / Al
Core and Coil Specifications
Dimension A
2.812"
0.250 Dia Thru
2 Holes
2.438"
3.500"
3.938"
Reference Drawing
Capacitor: 005-1415-MF
Ignitor: HPS150-3A
No. 1 (Red or Blue)
Lead Lengths (inches)
Coil Material (Pri. / Sec.):
No. 2 (Brown)
No. 3 (Yellow)
Document #:
010-11816-01
Date:
2/6/2007
Status:
Production
Replaces Catalog #:
12310-165
1.250"
2.000"
For alternate capacitor construction consult sales
Data is based upon tests performed by Universal Lighting Technologies in a controled environment and is representive of relative performance.
Actual performance may vary depending on operating conditions. Specifications are subject to change without notice.
2/2/2007
Universal Lighting Technologies
26 Century Blvd. Suite 500 - Nashville, TN 37214
Phone 1-800-225-5278 Fax 1-800-206-0035
www.universalballast.com
S250MLTAC4M
250W
High Pressure Sodium
60Hz CWA
Specification Sheet
120
208
240
277
±10%
±10%
±10%
±10%
±10%
Lamp Watts
±10%
±10%
±10%
±10%
±10%
Power Factor (min)
90%
90%
90%
90%
90%
295 W
295 W
295 W
295 W
295 W
190 V
190 V
190 V
190 V
190 V
2.50
1.45
1.25
1.10
Input Volts
Regulation
Line Volts
Input Watts
NOM. Open Circuit Voltage
Line Current (Amps)
Operating
S50
277V (BLACK)
LAMP
240V (VIOLET)
(RED/BLK)
3
1
3
208V (ORANGE)
STARTER
120V (BLK/YEL)
CAP
(RED)
Open Circuit
1.30
0.70
0.65
0.55
Starting
2.00
1.20
1.00
0.85
Recommended Fuse (Amps)
7
4
4
3
0
Lamp Dropout Voltage (Line)
90 V
160 V
180 V
210 V
V
COM (YEL)
UL Temperature Ratings
Insulation Class
Temperature Code
MIN. Starting Temperature
CAP
(RED)
2
COM (YEL)
Wiring Diagram
H (180°C) H (180°C) H (180°C) H (180°C) H (180°C)
B
B
B
B
-40°F -40°C
-40°F -40°C
-40°F -40°C
-40°F -40°C
A
0.250 Dia Thru
4 Holes
B
MAX
-40°F -40°C
CAPACITOR Specifications
Microfarads
Volts (min.)
35 uf
35 uf
35 uf
35 uf
35 uf
240 V
240 V
240 V
240 V
240 V
60Hz Test Procedures
High Potential Test 1 Minute
2000 V
2000 V
2000 V
2000 V
2000 V
High Potential Test 1 Second
2500 V
2500 V
2500 V
2500 V
2500 V
Secondary Open Ckt Voltage (V)
170 - 210
170 - 210
170 - 210
170 - 210
170 - 210
Secondary Current Shorted (A)
3.75 - 4.60
3.75 - 4.60
3.75 - 4.60
3.75 - 4.60
3.75 - 4.60
Input Operating Current (A)
2.25 - 2.75
1.30 - 1.60
1.10 - 1.40
1.00 - 1.20
-
Input Open Circuit Current (A)
0.65 - 1.90
0.35 - 1.00
0.35 - 0.90
0.30 - 0.80
-
Input Short Circuit Current (A)
1.55 - 2.30
0.90 - 1.35
0.80 - 1.15
0.65 - 1.00
-
Rated Temp
90 °C
Max Case Temp
105 °C
1.80 in
1.80 in
1.80 in
1.80 in
1.80 in
Height:
3.13 in
BTL:
10 ft
Dimension B
3.55 in
3.55 in
3.55 in
3.55 in
3.55 in
Width / Diameter:
2.91 in
Weight
10.0 lbs
10.0 lbs
10.0 lbs
10.0 lbs
10.0 lbs
12-14
12-14
12-14
12-14
12-14
Cu / Al
Cu / Al
Cu / Al
Cu / Al
Cu / Al
Core and Coil Specifications
Dimension A
4.250"
0.250 Dia Thru
2 Holes
3.875"
4.375"
4.750"
Reference Drawing
Capacitor: 005-1421-MF
Ignitor: HPS400-3A
No. 1 (Red or Blue)
Lead Lengths (inches)
Coil Material (Pri. / Sec.):
No. 2 (Brown)
No. 3 (Yellow)
Document #:
010-11949-00
Date:
12/9/2006
Status:
Production
Replaces Catalog #:
New Design
1.250"
2.000"
For alternate capacitor construction consult sales
Data is based upon tests performed by Universal Lighting Technologies in a controled environment and is representive of relative performance.
Actual performance may vary depending on operating conditions. Specifications are subject to change without notice.
11/10/2006
Universal Lighting Technologies
26 Century Blvd. Suite 500 - Nashville, TN 37214
Phone 1-800-225-5278 Fax 1-800-206-0035
www.universalballast.com
Specification Sheet
Catalog Number:
Document #:
Date:
Lamp Type
ANSI Designation
Line Voltage
Regulation
Frequency
Recommended Fuse
Circuit Type
Insulation Class
Capacitor Value
Capacitor Volt Rating
Capacitor Part Number
Lamp Starter
FEATURES:
Line
Volt
480
Line
Volt
480
S25048TAC4M
010-9759-00
5/27/03
250W HPS
S50
480 (120 Aux)
10%
60 HZ
2
CWA
180 C
35 MF
280
005-4075-P
HPS400-3A
Replaces Catalog #
Samples Available
Production Available
Agency Certification
Maximum Distance to Lamp
Electrical Characteristics
Line Current in Amps
Open
Power
Input
Circuit
Factor Oprtng Open
Start
Watts
Volts
High
0.62
0.38
0.36
285
200
Power
Factor
High
Height
4.25
Drop
Out
Volts
260
Min.
Start
Temp.
-40C
UL
Temp.
Code
A
Test Limits
Line Current, Amps
Open Circuit
Operating
Open
Short
Voltage (V)
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
0.56
0.69
0.19
0.54
0.25
0.45
185
215
Stack
1.85
Over
Coils
3.65
Reference Drawing
Short Circuit
Current (A)
Min.
Max.
3.30
4.40
Physical Characteristics
Mounting Holes (In.)
Bracket
CapacitorDim.
Mntng Dim
Diam Length Width Length Width
Dia.
Length
0.25
4.38
3.88
1.80
4.60
Application and Performance Specification Information Subject to Change without Notification.
For samples, contact your Universal Lighting Technologies Representative.
1-800-BALLAST
1232-321S
Yes
Yes
UL & CSA
5 FT
Utilizes Precise-Wound Coils
Overall Dimensions, Inches
Length
4.75
250W HIGH PRESSURE SODIUM
www.universalballast.com
Ballast
Net
Weight
10.40
Lead
Length
Inches
12-14
Specification Sheet
Catalog Number: S400MLTAC5M
Document #: 010-9770- 02
Date: 04/16/2004
Lamp Type
ANSI Designation
Line Voltage
Regulation
Frequency
Recommended Fuse
Circuit Type
Insulation Class
Capacitor Value
Capacitor Volt Rating
Capacitor Temp Rating
Capacitor Part Number
Lamp Starter
Winding Material (Pri/Sec)
FEATURES:
Line
Volt
120
208
240
277
400W HIGH PRESSURE SODIUM
400W HPS
S51 LAMP
120/208/240/277
10%
60 HZ
15/8/8/5
CWA
180° C
48MF
280 VOLTS
90° C
005-1422-MF
HPS 400-3A
Cu/Cu
Replaces Catalog #
Samples Available
Production Available
Agency Certification
Maximum Distance to Lamp
1230-93S
Yes
Yes
UL & CSA
10 FT
Utilizes Precise-Wound Coils
Electrical Characteristics
Line Current in Amps
Open
Power
Input
Circuit
Factor Oprtng
Open
Start
Watts
Volts
High
4.00
2.30
2.80
470
200
High
2.30
1.40
1.70
470
200
High
2.00
1.20
1.45
470
200
High
1.80
1.10
1.30
470
200
Drop
Out
Volts
85
145
170
195
Min.
Start
Temp.
-40°C
-40°C
-40°C
-40°C
UL
Temp.
Code
D
D
D
D
Reference Drawing
Line
Volt
120
208
240
277
Power
Factor
High
High
High
High
Test Limits
Line Current, Amps
Operating
Open
Min.
Max.
Min.
Max.
3.64
4.44
1.15
3.29
2.09
2.55
0.70
2.00
1.82
2.22
0.60
1.72
1.64
2.00
0.55
1.57
Physical Characteristics
Mounting Holes (In.)
Overall Dimensions, Inches
Length
5.75
Height
4.25
Stack
2.25
Open Circuit
Short
Voltage (V)
Min.
Max.
Min.
Max.
2.40
3.60
180
240
1.40
2.10
180
240
1.20
1.82
180
240
1.00
1.60
180
240
Over
Coils
4.13
Diam
0.25
Length
5.38
Width
3.88
Bracket
CapacitorDim.
Mntng Dim
Length Width Section Length
1.81
3.88
Application and Performance Specification Information Subject to Change without Notification.
For samples, contact your Universal Lighting Technologies Representative.
1-800-BALLAST
Short Circuit
Current (A)
Min.
Max.
5.35
8.00
5.35
8.00
5.35
8.00
5.35
8.00
www.universalballast.com
Ballast
Net
Weight
15.50
Lead
Length
Inches
12-14
Specification Sheet
Catalog Number:
Document #:
Date:
Lamp Type
ANSI Designation
Line Voltage
Regulation
Frequency
Recommended Fuse
Circuit Type
Insulation Class
Capacitor Value
Capacitor Volt Rating
Capacitor Part Number
FEATURES:
Line
Volt
480
S40048TAC5M
010-9767-00
2/28/2003
400W HPS
S51
480
10%
60 HZ
5
CWA
180 C
48 MF
280 VOLTS
005-4081-P
400W HIGH PRESSURE SODIUM
Replaces Catalog #
Samples Available
Production Available
Agency Certification
Maximum Distance to Lamp
1232-331S
Yes
Yes
UL & CSA
10 FT
Utilizes Precise-Wound Coils
Electrical Characteristics
Line Current in Amps
Open
Power
Input Circuit
Factor Oprtng Open
Start
Watts Volts
High
1.05
0.60
0.60
467
200
Drop
Min.
UL
Out
Start Temp.
Volts Temp. Code
330 -40°C
D
Reference Drawing
Line
Volt
480
Power
Factor
High
Test Limits
Line Current, Amps
Open Circuit
Operating
Open
Short
Voltage (V)
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
0.91
1.11
0.30
0.86
0.30
0.78
190
210
Overall Dimensions, Inches
Length Height
5.75
4.25
Stack
2.25
Over
Coils
4.25
Short Circuit
Current (A)
Min.
Max.
5.75
7.40
Physical Characteristics
Mounting Holes (In.)
Bracket
CapacitorDim.
Ballast Lead
Mntng Dim
Net
Length
Diam Length Width Length Width
Dia.
Length Weight Inches
0.25
5.38
3.88
1.80
4.60
15.50
12-14
Application and Performance Specification Information Subject to Change without Notification.
For samples, contact your Universal Lighting Technologies Representative.
1-800-BALLAST
www.universalballast.com
Specification Sheet
Catalog Number:
Document #:
Date:
Lamp Type
ANSI Designation
Line Voltage
Regulation
Frequency
Recommended Fuse
Circuit Type
Insulation Class
Capacitor Value
Capacitor Volt Rating
Capacitor Temp Rating
Capacitor Part Number
Winding Material (Pri/Sec)
Lamp Starter
FEATURES:
Line
Volt
120
208
240
277
S1000MLTAC5M
010-9752- 02
06/23/2004
1000 W HIGH PRESSURE SODIUM
1000W HPS
S52
120/208/240/277
10%
60 HZ
20/15/10/10
CWA
180° C
26MF
525 VOLTS
90° C
005-2776-MF
Cu/Cu
HPS 1000-4B
Replaces Catalog #
Samples Available
Production Available
Agency Certification
Maximum Distance to Lamp
1230-97S
Yes
Yes
UL & CSA
15 FT
Utilizes Precise-Wound Coils
Power
Factor
High
High
High
High
Electrical Characteristics
Line Current in Amps
Open
Input
Circuit
Oprtng Open
Start
Watts
Volts
9.50
6.10
5.00
1100
440
5.50
3.50
3.00
1100
440
4.80
3.10
2.60
1100
440
4.20
2.70
2.20
1100
440
Drop
Out
Volts
90
155
180
208
Min.
Start
Temp.
-40°C
-40°C
-40°C
-40°C
UL
Temp.
Code
C
C
C
C
Reference Drawing
Line
Volt
120
208
240
277
Power
Factor
High
High
High
High
Operating
Min.
Max.
8.65
10.55
5.01
6.11
4.37
5.33
3.82
4.66
Physical Characteristics
Mounting Holes (In.)
Overall Dimensions, Inches
Length
5.75
Height
4.25
Stack
3.75
Test Limits
Line Current, Amps
Open
Short
Min.
Max.
Min.
Max.
3.05
8.72
5.30
8.00
1.75
5.01
3.10
4.70
1.55
4.43
2.65
4.00
1.35
3.86
2.30
3.50
Over
Coils
5.63
Diam
0.25
Length
5.38
Width
3.88
Bracket
Mntng Dim
Length
Width
-
Application and Performance Specification Information Subject to Change without Notification.
For samples, contact your Universal Lighting Technologies Representative.
1-800-BALLAST
Open Circuit
Voltage (V)
Min.
Max.
400
485
400
485
400
485
400
485
www.universalballast.com
Short Circuit
Current (A)
Min.
Max.
6.40
8.00
6.40
8.00
6.40
8.00
6.40
8.00
CapacitorDim.
Section
1.81
Length
4.25
Ballast
Net
Weight
26.00
Lead
Length
Inches
12-14
Specification Sheet
Catalog Number:
Document #:
Date:
Lamp Type
ANSI Designation
Line Voltage
Regulation
Frequency
Recommended Fuse
Circuit Type
Insulation Class
Capacitor Value
Capacitor Volt Rating
Capacitor Part Number
Starter
FEATURES:
Line
Volt
480
Line
Volt
480
S100048TAC5M
010-9762-02
2/6/04
1000W HPS
S52
480 (120V Aux.)
10%
60 HZ
8
CWA
180 C
26 MF
525 VOLTS
005-2776-MF
HPS1000-4B
Replaces Catalog #
Samples Available
Production Available
Agency Certification
Maximum Distance to Lamp
Electrical Characteristics
Line Current in Amps
Open
Power
Input
Circuit
Factor Oprtng Open
Start
Watts
Volts
High
2.45
1.50
1.80
1100
440
Power
Factor
High
Height
4.25
Test Limits
Line Current, Amps
Operating
Open
Min.
Max.
Min.
Max.
2.18
2.66
0.75
2.15
Stack
3.75
Over
Coils
6.00
Drop
Out
Volts
360
Min.
Start
Temp.
-40°C
UL
Temp.
Code
D
Open Circuit
Short
Voltage (V)
Min.
Max.
Min.
Max.
1.26
2.16
425
465
Reference Drawing
Short Circuit
Current (A)
Min.
Max.
6.00
7.65
Physical Characteristics
Mounting Holes (In.)
Bracket
CapacitorDim.
Mntng Dim
Diam Length Width Length Width Section Length
0.25
5.38
3.88
1.91
4.25
Application and Performance Specification Information Subject to Change without Notification.
For samples, contact your Universal Ligthing Technologies Representative.
1-800-BALLAST
1232-571S
Yes
Yes
UL & CSA
15 FT
Utilizes Precise-Wound Coils
Overall Dimensions, Inches
Length
5.75
1000W HIGH PRESSURE SODIUM
www.universalballast.com
Ballast
Net
Weight
25.00
Lead
Length
Inches
12-14
Specification Sheet
Catalog Number: S40048TAC4M
Document #: 010-9654-03
Date: 04/30/2004
Lamp Type
ANSI Designation
Line Voltage
Regulation
Frequency
Recommended Fuse
Circuit Type
Insulation Class
Capacitor Value
Capacitor Volt Rating
Capacitor Temp Rating
Capacitor Part Number
Lamp Starter
Winding Material (Pri/Sec)
FEATURES:
Line
Volt
480
400W HIGH PRESSURE SODIUM
400W HPS
S51
480
10%
60 HZ
5
CWA
180° C
55 MF
240 VOLTS
90° C
005-1594-MF
HPS400-3A
Cu/Cu
Replaces Catalog #
Samples Available
Production Available
Agency Certification
Maximum Distance to Lamp
1232-331U
Yes
Yes
UL & CSA
10 FT
Utilizes Precise-Wound Coils
Electrical Characteristics
Line Current in Amps
Open
Power
Input Circuit
Factor Oprtng
Open
Start
Watts Volts
High
1.00
0.42
0.80
465
190
Drop Min.
UL
Out
Start Temp.
Volts Temp. Code
340 -40°C
D
Reference Drawing
Line
Volt
480
Power
Factor
High
Test Limits
Line Current, Amps
Open Circuit
Operating
Open
Short
Voltage (V)
Min.
Max.
Min.
Max.
Min.
Max. Min.
Max.
0.91
1.11
0.21
0.60
0.50
0.90
170
210
Overall Dimensions, Inches
Length Height
4.75
4.25
Stack
2.44
Over
Coils
4.12
Short Circuit
Current (A)
Min.
Max.
6.00
7.45
Physical Characteristics
Mounting Holes (In.)
Bracket
CapacitorDim.
Ballast Lead
Mntng Dim
Net
Length
Diam Length Width Length Width
Dia.
Length Weight Inches
0.25
4.38
3.88
1.81
3.50
14.50
12-14
Application and Performance Specification Information Subject to Change without Notification.
For samples, contact your Universal Lighting Technologies Representative.
1-800-BALLAST
www.universalballast.com
Specification Sheet
Catalog Number: S400MLTAC4M
Document #: 010-9653- 02
Date: 04/20/2004
Lamp Type
ANSI Designation
Line Voltage
Regulation
Frequency
Recommended Fuse
Circuit Type
Insulation Class
Capacitor Value
Capacitor Volt Rating
Capacitor Temp Rating
Capacitor Part Number
Lamp Starter
Winding Material (Pri/Sec)
FEATURES:
Line
Volt
120
208
240
277
400W HIGH PRESSURE SODIUM
400W HPS
S51
120/208/240/277
10%
60 HZ
15/8/8/5
CWA
180° C
55MF
240 VOLTS
90° C
005-1594-MF
HPS 400-3A
Cu/Cu
Replaces Catalog #
Samples Available
Production Available
Agency Certification
Maximum Distance to Lamp
1230-93U
Yes
Yes
UL & CSA
10 FT
Utilizes Precise-Wound Coils
Electrical Characteristics
Line Current in Amps
Open
Power
Input
Circuit
Factor Oprtng
Open
Start
Watts
Volts
High
3.80
1.85
3.10
440
190
High
2.20
1.10
1.80
440
190
High
1.80
0.90
1.60
440
190
High
1.60
0.80
1.35
440
190
Drop
Out
Volts
85
145
170
195
Min.
Start
Temp.
-40C
-40C
-40C
-40C
UL
Temp.
Code
D
D
D
D
Reference Drawing
Line
Volt
120
208
240
277
Power
Factor
High
High
High
High
Test Limits
Line Current, Amps
Open Circuit
Operating
Open
Short
Voltage (V)
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
3.46
4.22
0.93
2.65
2.20
3.40
170
210
2.00
2.44
0.55
1.57
1.30
2.00
170
210
1.64
2.00
0.45
1.29
1.14
1.72
170
210
1.46
1.78
0.40
1.14
0.95
1.50
170
210
Physical Characteristics
Mounting Holes (In.)
Overall Dimensions, Inches
Length
4.75
Height
4.25
Stack
2.32
Over
Coils
4.19
Diam
0.25
Length
4.38
Width
3.88
Bracket
CapacitorDim.
Mntng Dim
Length Width Section Length
1.81
3.50
Application and Performance Specification Information Subject to Change without Notification.
For samples, contact your Universal Lighting Technologies Representative.
1-800-BALLAST
Short Circuit
Current (A)
Min.
Max.
6.00
7.60
6.00
7.60
6.00
7.60
6.00
7.60
www.univeralballast.com
Ballast
Net
Weight
14.50
Lead
Length
Inches
12-14
MH
70
HID CORE & COIL BALLASTS
• 60 Hz
• Minimum starting
temperature: -30° C
• Normal and High Power
Factor models available
WATT
Nom
Max Open
Circuit Watts Input Circuit Fuse Wir
Input
Catalog*
Volts
Number
Type Input Current Voltage Rating Dia
(1) 70 WATT M98 METAL HALIDE LAMP - Medium Base
120 or
1.70
4
1.04
3
208 or
M70MLTLC3M
HX-HPF 95
245
4
240 or
0.87
3
277
0.78
2
120 or
1.70
4
M70TRILC3M
HX-HPF 95
0.78
245
2
4A
277 or
347
0.60
2
480-120
M7048TLC3M
HX-HPF 95
0.50
245
1
6
(1) 70 WATT M85 METAL HALIDE LAMP - Double Ended
120 or
1.70
4
208 or
1.04
3
HX-HPF 95
245
4
M70MLTLC3D
240 or
0.87
3
277
0.78
2
DESCRIPTION
METAL HALIDE
Dimensions
Ref
Dwg
Capacitor
A
Min
Mfd Volt
B
Dry Film
Dia
Ht
Ignitor
Total
Weight
(lbs.)
Oil Filled
Oval
Ht
Max
UL
Catalog Distance Bench
Number to lamp (ft) Top Rise
PC1
1.3
2.9
8
280
1.2
2.7
1.31x2.16
2.2
4.3
MH100-3A
10
A
B
B
B
PC1
1.3
2.9
8
280
1.2
2.7
1.31x2.16
2.2
4.3
MH100-3A
10
A
PC1
1.3
2.9
8
300
1.2
2.7
1.31x2.16
2.2
4.3
MH100-3A
10
E
10
A
B
B
B
PC1
1.4
2.8
8
300
1.2
2.7
1.31x2.16
2.2
4.3
MH70-3B
SUFFIX *
For Ballast Only
For Bracket Only (see pg. 5-7)
For Capacitor Only (see pg. 5-5, 5-6)
For Distributor Replacement Kit
(see pg. 5-13 thru 5-15)
For Canadian Distributor
Replacement Kit (see pg. 5-16)
For Dry-Capacitor & Ballast
(see pg. 5-6)
For Bracket & Capacitor
(see pg. 5-5, 5-7)
For Bracket & Dry-Capacitor
(see pg. 5-6, 5-7)
000
200
500
REFERENCE DRAWING PC1
0.199 Dia Thru
4 Holes
A
B
MAX
500K
2.812˝
0.250 Dia Thru
2 Holes
502K
518
2.438˝
3.500˝ 3.938˝
700
718
Wiring Diagram 4A
Wiring Diagram 4
277V
L
W
5.25” 1.25”
M
4.60”
S
0.25”
Cap
(Yellow)
208V
120V
BRef. Dwg.
PC1
Lamp Eyelet
3
277V
(Blue)
1
3
120V
Cap
Cap
347V
240V
(Black)
M
L
STARTER
2
Com
(Yellow)
(Blue)
1
3
STARTER
To Lamp Shell
(Yellow)
Wiring Diagram 6
120V
(AUX)
INC LAMP
W MAX
(White) (Black)
or (Yellow)
Line
Cap
See p. 5-7 for adjustable mounting brackets and detailed bracket drawings.
Lamp Eyelet
3
2
To Lamp Shell
Com
Cap
S
(Black)
Bracket
(Yellow)
W
Cap
HID
CORE & COIL
WIRING DIAGRAMS
Lamp Eyelet
(Blue)
3
1
3
STARTER
2
PERMISSIBLE
To Lamp Shell
Com (White) or (Yellow)
PAGE 5-18
FOR MORE INFORMATION CALL
1-800-BALLAST
(225-5278)
HID CORE & COIL BALLASTS
METAL HALIDE
Nom
Dimensions
Max Open
Circuit Watts Input Circuit Fuse Wir Ref
Input
Catalog*
Volts
Number
Type Input Current Voltage Rating Dia Dwg
A
(1) 100 WATT M90 OR M92 METAL HALIDE LAMP - Medium Base
5
R-NPF
1.45
1
1
1.5
277
118
277
1133-14R
1.05
3
R-HPF 3
120 or
2.30
5
208 or
1.30
4
M100MLTLC3M HX-HPF 130
250
4 PC1
1.7
240 or
1.10
3
277
0.95
3
480-120 M10048TLC3M HX-HPF 140
0.62
250
2
6 PC1
1.7
120 or
2.30
5
277 or
M100TRILC3M HX-HPF 130
0.95
250
3
4A PC1
1.7
347
0.80
3
(1) 100 WATT M91 METAL HALIDE LAMP - Double Ended
120 or
2.30
5
1.30
4
208 or
250
17 PC1
2.0
M100MLTLC3D HX-HPF 130
240 or
1.10
3
277
0.95
3
3
MH
100
• 60 Hz
• Minimum starting
temperature: -30° C
• Normal and High Power
Factor models available
WATT
Capacitor
Min
Mfd Volt
B
Ignitor
Dry Film
Dia
Ht
Oil Filled
Oval
Ht
Total
Weight
(lbs.)
Max
UL
Catalog Distance Bench
Number to lamp (ft) Top Rise
2.5
—
10
—
280
—
1.56
—
2.69
—
1.31x2.16
—
2.2
2.4
MH100-3A
5
E
3.2
10
280
1.2
2.7
1.31x2.16
2.2
6.3
MH100-3A
10
A
3.2
10
280
1.2
2.7
1.31x2.16
2.2
5.0
MH100-3A
10
C
3.2
10
280
1.2
2.7
1.31x2.16
2.2
6.3
MH100-3A
10
A
3.5
10
280
1.2
2.7
1.31x2.16
2.7
6.3
MH70-3B
5
A
Capacitors are available as an option for high power
factor operation.
DESCRIPTION
SUFFIX *
For Ballast Only
For Bracket Only (see pg. 5-7)
For Capacitor Only (see pg. 5-5, 5-6)
For Distributor Replacement Kit
(see pg. 5-13 thru 5-15)
For Canadian Distributor
Replacement Kit (see pg. 5-16)
For Dry-Capacitor & Ballast
(see pg. 5-6)
For Bracket & Capacitor
(see pg. 5-5, 5-7)
For Bracket & Dry-Capacitor
(see pg. 5-6, 5-7)
REFERENCE DRAWING PC1
000
200
500
REFERENCE DRAWING 1
0.438"
0.199 Dia Thru
4 Holes
500K
A
.203" Dia Thru
4 Holes
A
B
MAX
B
0.594"
2.812˝
0.250 Dia Thru
2 Holes
502K
518
2.438˝
1.750"
2.188"
3.500˝ 3.938˝
700
2.188"
2.625"
718
WIRING DIAGRAMS
Bracket
S
Wiring Diagram 1
Wiring Diagram 4
Wiring Diagram 4A
M
3.35”
4.60”
S
0.25”
0.25”
120V
STARTER
Cap
120V
(Blue)
1
3
Cap
3
STARTER
(Yellow)
Cap
(Black)
277V
Lamp Eyelet
208V
Cap
Cap
1
3
(Yellow)
L
W
4.00” 0.75”
5.25” 1.25”
240V
(Blue)
3
208V
120V
BRef. Dwg.
1
PC1
Lamp Eyelet
(Yellow)
Cap
240V
(Black)
M
L
277V
(Black)
347V
277V
Lamp Eyelet
3
(Blue)
1
3
STARTER
2
2
2
Com
To Lamp Shell
Com
(Yellow)
To Lamp Shell
Com
To Lamp Shell
(Yellow)
(Yellow)
See p. 5-7 for adjustable mounting brackets and detailed bracket drawings.
Wiring Diagram 17
Wiring Diagram 6
Cap
Cap
(AUX)
INC LAMP
W MAX
PERMISSIBLE
(White) (Black)
or (Yellow)
120V
Blue/White
Trace
240V
Lamp Eyelet
(Blue)
3
1
3
208V
STARTER
120V
2
To Lamp Shell
Com (White) or (Yellow)
Com
(Yellow)
PAGE 5-19
Cap
Cap
(Red)
(Red)
IGNITOR
277V
Line
(Blue)
Yellow/Red
Trace
Com
(Yellow)
FOR MORE INFORMATION CALL
1-800-BALLAST
(225-5278)
HID
CORE & COIL
W
Specification Sheet
Catalog Number: M150MLTLC3M
Document #: 010-9705-03
Date: 12/06/2004
Lamp Type
ANSI Designation
Line Voltage
Regulation
Frequency
Recommended Fuse
Circuit Type
Insulation Class
Capacitor Value
Capacitor Volt Rating
Capacitor Temp Rating
Capacitor Part Number
Lamp Starter
Winding Material (Pri/Sec)
FEATURES:
Line
Volt
120
208
240
277
150W METAL HALIDE
150W MH
M102 or M142
120/208/240/277
5%
60 HZ
10/5/5/4
HX-HPF
180° C
16 MF
300 VOLTS
90° C
005-1498-MF
MH100-3A
Cu/Cu
Replaces Catalog #
Samples Available
Production Available
Agency Certification
Maximum Distance to Lamp
11310-543
Yes
Yes
UL & CSA
10 FT
Utilizes Precise-Wound Coils
Electrical Characteristics
Line Current in Amps
Power
Factor Oprtng Open
Start
High
1.57
3.32
1.70
High
0.91
1.93
1.00
High
0.81
1.66
0.80
High
0.74
1.48
0.77
Input
Watts
185
185
185
185
Open
Circuit
Volts
245
245
245
245
Drop
Min.
UL
Out
Start Temp.
Volts Temp. Code
75
-30°C
D
125 -30°C
D
150 -30°C
D
160 -30°C
D
Reference Drawing
Test Limits
Line
Volt
120
208
240
277
Power
Factor
High
High
High
High
Line Current, Amps
Operating
Open
Min.
Max.
Min.
Max.
1.43
1.74
1.66
4.75
0.83
1.01
0.97
2.76
0.74
0.90
0.83
2.37
0.67
0.82
0.74
2.12
Open Circuit
Short
Voltage (V)
Min.
Max. Min.
Max.
0.85
1.25
230
265
0.50
0.72
230
265
0.42
0.62
230
265
0.40
0.60
230
265
Short Circuit
Current (A)
Min.
Max.
1.90
2.40
1.90
2.40
1.90
2.40
1.90
2.40
Physical Characteristics
Overall Dimensions, Inches
Mounting Holes (In.)
Bracket
CapacitorDim.
Ballast Lead
Over
Mntng Dim
Net
Length
Length Height Stack
Coils
Diam Length Width Length Width
Dia.
Length Weight Inches
3.94
2.81
2.38
3.88
0.25
3.50
2.44
1.56
2.69
7.25
12-14
For samples, contact your Universal Lighting Technologies Representative.
Application and Performance Specification Information Subject to Change without Notification.
1-800-BALLAST
www.universalballast.com
MH
150
HID CORE & COIL BALLASTS
• 60 Hz
• Minimum starting
temperature: -30° C
• High Power Factor models
available
WATT
Nom
Max Open
Circuit Watts Input Circuit Fuse Wir
Input
Catalog*
Volts
Number
Type Input Current Voltage Rating Dia
(1) 150 WATT M102 METAL HALIDE LAMP - Medium Base
120 or
3.32
10
277 or
M150TRILC3M HX-HPF 185
1.48
245
4
4A
347
0.65
2
120 or
3.32
10
208 or
1.93
5
M150MLTLC3M HX-HPF 185
245
4
240 or
1.66
5
277
1.48
4
480-120 M15048TLC3M HX-HPF 180
1.00
245
2
6
(1) 150 WATT M81 METAL HALIDE LAMP - Double Ended
120 or
3.32
10
208 or
1.93
5
245
17
M150MLTLC3D HX-HPF 185
240 or
1.66
5
277
1.48
4
DESCRIPTION
Dimensions
Capacitor
Min
Mfd Volt
Ignitor
Dry Film
Dia
Ht
Total
Weight
(lbs.)
Oil Filled
Oval
Ht
Max
UL
Catalog Distance Bench
Number to lamp (ft) Top Rise
Ref
Dwg
A
B
PC1
2.3
3.9
16
280
1.6
2.7
1.56x2.69
2.7
7.3
MH100-3A
10
D
PC1
2.3
3.9
16
300
1.6
2.7
1.56x2.69
2.7
7.3
MH100-3A
10
D
PC1
2.3
3.9
16
280
1.6
2.7
1.56x2.69
2.7
7.3
MH100-3A
10
F
PC1
2.3
3.9
16 280
1.6
2.7
1.56x2.69
2.7
7.3
MH70-3B
10
D
REFERENCE DRAWING PC1
SUFFIX *
For Ballast Only
For Bracket Only (see pg. 5-7)
For Capacitor Only (see pg. 5-5, 5-6)
For Distributor Replacement Kit
(see pg. 5-13 thru 5-15)
For Canadian Distributor
Replacement Kit (see pg. 5-16)
For Dry-Capacitor & Ballast
(see pg. 5-6)
For Bracket & Capacitor
(see pg. 5-5, 5-7)
For Bracket & Dry-Capacitor
(see pg. 5-6, 5-7)
METAL HALIDE
000
200
500
0.199 Dia Thru
4 Holes
A
B
MAX
500K
2.812˝
0.250 Dia Thru
2 Holes
502K
518
700
2.438˝
3.500˝ 3.938˝
718
Wiring Diagram 4A
Wiring Diagram 4
347V
3
M
4.60”
S
0.25”
120V
Cap
277V
Lamp Eyelet
208V
Cap
L
W
5.25” 1.25”
240V
(Yellow)
BRef. Dwg.
PC1
Cap
M
L
(Black)
277V
120V
(Blue)
1
3
(Black)
S
Cap
Bracket
(Yellow)
W
Lamp Eyelet
3
(Blue)
1
3
STARTER
STARTER
2
To Lamp Shell
Com
2
(Yellow)
To Lamp Shell
Com
See p. 5-7 for adjustable mounting brackets and detailed bracket drawings.
(Yellow)
Wiring Diagram 6
Wiring Diagram 17
Cap
(AUX)
Cap
120V
INC LAMP
W MAX
PERMISSIBLE
Lamp Eyelet
Blue/White
Trace
240V
(Blue)
3
1
3
208V
STARTER
120V
2
Cap
Cap
(Red)
(Red)
IGNITOR
277V
Line
(White) (Black)
or (Yellow)
HID
CORE & COIL
WIRING DIAGRAMS
(Blue)
Yellow/Red
Trace
To Lamp Shell
Com
(Yellow)
Com (White) or (Yellow)
PAGE 5-20
Com
(Yellow)
FOR MORE INFORMATION CALL
1-800-BALLAST
(225-5278)
HID CORE & COIL BALLASTS
METAL HALIDE
Input
Volts
Catalog*
Number
• 60 Hz
• Minimum starting
temperature: -30° C
• Feature CWA design
Nom
Dimensions
Max Open
Circuit Watts Input Circuit Fuse Wir Ref
Type Input Current Voltage Rating Dia Dwg
A
B
(1) 175 WATT M57, M107 METAL HALIDE OR H39 MERCURY LAMPS
277
M175277AC3M
CWA 213 0.78
310
2
18 2
2.3
480-120 M17548TAC3M
CWA 213 0.51
310
1.5 19 PC1 2.8
120 or
1.80
5
277 or M175TRIAC3M CWA 213 0.78
310
2
23 PC1 2.2
347
0.62
2
120 or
1.80
5
208 or M175MLTAC3M CWA 213 1.10
3
310
21 PC1 2.2
240 or
0.90
3
277
0.78
2
120 or
208 1.90
5
208
1.10
3
208 or
240 or M175ML5AC3M CWA 208 0.95
300
3
44 PC1 2.3
277 or
208 0.85
2
480
210 0.50
1.5
DESCRIPTION
SUFFIX *
For Ballast Only
For Bracket Only (see pg. 5-7)
For Capacitor Only (see pg. 5-5, 5-6)
For Distributor Replacement Kit
(see pg. 5-13 thru 5-15)
For Canadian Distributor
Replacement Kit (see pg. 5-16)
For Dry-Capacitor & Ballast
(see pg. 5-6)
For Bracket & Capacitor
(see pg. 5-5, 5-7)
For Bracket & Dry-Capacitor
(see pg. 5-6, 5-7)
MH
175
WATT
Capacitor
Oil Filled
Oval
Ht
Max
UL
Catalog Distance Bench
Number to lamp (ft) Top Rise
Min
Mfd Volt
Dry Film
Dia
Ht
3.5
4.2
10 400
10 400
1.6
1.6
2.7
2.7
1.56x2.69
1.56x2.69
2.7
2.7
6.8
6.8
n/a
n/a
n/a
n/a
3.7
10 400
1.6
2.7
1.56x2.69
2.7
6.8
n/a
n/a
3.6
10 400
1.6
2.7
1.56x2.69
2.7
6.8
n/a
n/a
3.6
10 400
1.6
2.7
1.56x2.69
2.7
6.8
n/a
n/a
REFERENCE DRAWING PC1
A
B
.250" Dia Thru
2 Holes
2.812˝
500K
0.250 Dia Thru
2 Holes
502K
2.437"
2.438˝
3.500˝ 3.938˝
2.812"
1.218"
518
3.500"
3.938"
700
718
WIRING DIAGRAMS
Wiring Diagram 19
Line
Cap
(Red)
Line
HID
CORE & COIL
Wiring Diagram 18
Cap
(Red)
120V (AUX)
INC LAMP
W MAX
W
Bracket
S
M
L
BRef. Dwg.
PC1, 2
L
W
5.25” 1.25”
Com
(White)
or
Com
(Yellow)
Wiring Diagram 23
See p. 5-7 for adjustable mounting brackets and detailed bracket drawings.
277V
240V
208V
Cap
(Red)
Cap
(Red)
120V
120V
Com
(Yellow)
Wiring Diagram 44
347V
277V
S
0.25”
Com (Yellow)
or (White)
PERMISSIBLE
Com (Yellow)
or (White)
Wiring Diagram 21
M
4.60”
B
0.438"
.199" Dia Thru
4 Holes
A
B
MAX
A
D
B
B
D
A
B
A
A
REFERENCE DRAWING 2
0.199 Dia Thru
4 Holes
000
200
500
Ignitor
Total
Weight
(lbs.)
Com
(Yellow)
PAGE 5-21
Com
(White)
Com
(White)
FOR MORE INFORMATION CALL
1-800-BALLAST
(225-5278)
HID CORE & COIL BALLASTS
METAL HALIDE FEATURING MULTI-5™
Nom
Dimensions
Max Open
Circuit Watts Input Circuit Fuse Wir Ref
Input
Catalog*
Volts
Number
Type Input Current Voltage Rating Dia Dwg
A
B
(1) 250 WATT M58 METAL HALIDE OR H37 MERCURY LAMPS - 4.75” Frame
120 or
2.50
8
208 or
1.40
5
305
4
44 PC2 1.8
3.6
240 or M250ML5AC4M CWA 293 1.30
277 or
1.10
3
480
0.65
2
120 or
3.05
8
CWA 293 1.25
305
3
23 PC2 1.6
3.6
277 or M250TRIAC4M
347
1.05
3
120 or
3.05
8
1.65
5
208 or
21 PC2 1.6
3.2
CWA 293
305
M250MLTAC4M
240 or
1.55
4
277
1.25
3
480-120 M25048TAC4M
CWA 293 0.70
305
2
18 PC2 1.6
3.2
DESCRIPTION
MH
250
• 60 HZ.
• Minimum Starting
Temperature: -30° C
• Feature CWA Design
WATT
Capacitor
Ignitor
Oil Filled
Oval
Ht
Total
Weight
(lbs.)
Max
UL
Catalog Distance Bench
Number to lamp (ft) Top Rise
Min
Mfd Volt
Dry Film
Dia
Ht
15 400
1.6
3.6
1.91x2.91
2.7
10.8
n/a
n/a
A
15 400
1.6
3.6
1.91x2.91
2.7
9.5
n/a
n/a
A
15 400
1.6
3.6
1.91x2.91
2.7
9.5
n/a
n/a
B
15 400
1.6
3.6
1.91x2.91
2.7
9.5
n/a
n/a
B
SUFFIX *
For Ballast Only
For Bracket Only (see pg. 5-7)
For Capacitor Only (see pg. 5-5, 5-6)
For Distributor Replacement Kit
(see pg. 5-13 thru 5-15)
For Canadian Distributor
Replacement Kit (see pg. 5-16)
For Dry-Capacitor & Ballast
(see pg. 5-6)
For Distributor Ballast Lamp
Replacement Kit (see pg. 5-12)
For Bracket & Capacitor
(see pg. 5-5, 5-7)
For Bracket & Dry-Capacitor
(see pg. 5-6, 5-7)
000
200
500
REFERENCE DRAWING PC2
0.250 Dia Thru
4 Holes
A
B
MAX
500K
4.250˝
502K
0.250 Dia Thru
2 Holes
518
3.875˝
4.375˝ 4.750˝
555K
700
718
WIRING DIAGRAMS
HID
CORE & COIL
Wiring Diagram 18
Wiring Diagram 21
277V
W
Bracket
S
L
W
5.25” 1.25”
Line
240V
208V
Cap
(Red)
120V
M
L
BRef. Dwg.
PC 2
Cap
(Red)
Com
(White)
M
4.60”
S
0.25”
See p. 5-7 for adjustable mounting brackets and detailed bracket drawings.
or
Com
(Yellow)
Com
(Yellow)
Wiring Diagram 23
Com
(Yellow)
Wiring Diagram 44
347V
277V
Cap
(Red)
120V
Com
(White)
Com
(White)
PAGE 5-23
FOR MORE INFORMATION CALL
1-800-BALLAST
(225-5278)
MH
250
HID CORE & COIL BALLASTS
• 60 HZ.
• Minimum Starting
Temperature: -30° C
• Feature CWA Design
WATT
METAL HALIDE
Nom
Dimensions
Max Open
Circuit Watts Input Circuit Fuse Wir Ref
Input
Catalog*
Volts
Number
Type Input Current Voltage Rating Dia Dwg
A
(1) 250 WATT M58 METAL HALIDE OR H37 MERCURY LAMP - 4” Frame
480-120 M25048TAC3M CWA 294 0.64
280
2
19 PC1 3.0
120 or
3.05
8
305
3
23 PC1 3.0
277 or M250TRIAC3M CWA 293 2.10
347
1.05
3
120 or
2.60
8
208 or M250MLTAC3M CWA 294 1.58
5
280
21 PC1 3.0
240 or
1.30
4
277
1.12
3
120 or
2.60
8
208 or
1.60
5
240 or M250ML5AC3M CWA 280 1.30
290
4
44 PC1 3.0
277 or
1.20
3
480
0.70
2
DESCRIPTION
Capacitor
Ignitor
Oil Filled
Oval
Ht
Total
Weight
(lbs.)
Max
UL
Catalog Distance Bench
Number to lamp (ft) Top Rise
B
Min
Mfd Volt
Dry Film
Dia
Ht
4.3
15 400
1.6
3.6
1.91x2.91
2.7
9.0
n/a
n/a
D
4.5
15 400
1.6
3.6
1.91x2.91
2.7
9.0
n/a
n/a
D
4.3
15 400
1.6
3.6
1.91x2.91
2.7
9.0
n/a
n/a
4.3
15 400
1.6
3.6
1.91x2.91
2.7
9.0
n/a
n/a
C
D
C
C
B
B
B
C
C
SUFFIX *
For Ballast Only
For Bracket Only (see pg. 5-7)
For Capacitor Only (see pg. 5-5, 5-6)
For Distributor Replacement Kit
(see pg. 5-13 thru 5-15)
For Canadian Distributor
Replacement Kit (see pg. 5-16)
For Dry-Capacitor & Ballast
(see pg. 5-6)
For Distributor Ballast Lamp
Replacement Kit (see pg. 5-12)
For Bracket & Capacitor
(see pg. 5-5, 5-7)
For Bracket & Dry-Capacitor
(see pg. 5-6, 5-7)
000
200
500
REFERENCE DRAWING PC1
500K
0.199 Dia Thru
4 Holes
502K
A
B
MAX
518
2.812˝
0.250 Dia Thru
2 Holes
555K
700
2.438˝
3.500˝ 3.938˝
718
HID
CORE & COIL
WIRING DIAGRAMS
W
Bracket
S
Wiring Diagram 19
Wiring Diagram 21
Line
M
L
BRef. Dwg.
PC1
L
W
5.25” 1.25”
277V
Cap
(Red)
240V
120V (AUX)
M
4.60”
S
0.25”
208V
INC LAMP
W MAX
Cap
(Red)
120V
PERMISSIBLE
Com (Yellow)
Com (Yellow)
or (White)
or (White)
Com
(Yellow)
Com
(Yellow)
See p. 5-7 for adjustable mounting brackets and detailed bracket drawings.
Wiring Diagram 23
Wiring Diagram 44
347V
277V
Cap
(Red)
120V
Com
(White)
Com
(White)
PAGE 5-22
FOR MORE INFORMATION CALL
1-800-BALLAST
(225-5278)
MH
400
• 60 Hz
• Minimum Starting
Temperature: -30° C
• CWA Designs
WATT
HID CORE & COIL BALLASTS
METAL HALIDE
Nom
Dimensions
Max Open
Circuit Watts Input Circuit Fuse Wir Ref
Input
Catalog*
Volts
Number
Type Input Current Voltage Rating Dia Dwg
A
(1) 400 WATT M59 METAL HALIDE OR H33 MERCURY LAMP
120
M400120AC4M CWA 458 4.00
300
10 18 PC2 2.0
480-120 M40048TAC4M CWA 458 1.00
300
5
19 PC2 2.0
120
4.00
10
277
M400TRIAC4M CWA 458
1.70
300
5
23 PC2 2.0
347
1.35
5
120 or
4.00
10
208 or
2.30
8
M400MLTAC4M CWA 458
300
21 PC2 2.0
240 or
2.00
5
277
1.70
5
120 or
4.00
10
208 or
2.30
8
300
21 PC2 2.0
M400MLTAC4L CWA 440
240 or
2.00
5
277
1.70
5
120 or
4.00
10
208 or
2.30
8
240 or M400ML5AC4M CWA 458
2.00
300
5
44 PC2 2.0
277 or
1.70
5
480
1.00
5
DESCRIPTION
SUFFIX *
For Ballast Only
For Bracket Only (see pg. 5-7)
For Capacitor Only (see pg. 5-5, 5-6)
For Distributor Replacement Kit
(see pg. 5-13 thru 5-15)
For Canadian Distributor
Replacement Kit (see pg. 5-16)
For Dry-Capacitor & Ballast
(see pg. 5-6)
For Distributor Ballast Lamp
Replacement Kit (see pg. 5-12)
For Bracket & Capacitor
(see pg. 5-5, 5-7)
For Bracket & Dry-Capacitor
(see pg. 5-6, 5-7)
Capacitor
Ignitor
Max
UL
Catalog Distance Bench
Number to lamp (ft) Top Rise
B
Min
Mfd Volt
Dry Film
Dia
Ht
3.9
3.9
24 400
24 400
1.8
1.8
3.6
3.6
1.91x2.91
1.91x2.91
3.1
3.1
11.2
11.2
n/a
n/a
n/a
n/a
3.9
24 400
1.8
3.6
1.91x2.91
3.1
11.2
n/a
n/a
3.9
24 360
1.8
3.6
1.91x2.91
3.1
11.2
n/a
n/a
3.9
24 400
1.8
3.6
1.91x2.91
3.1
13.0
n/a
n/a
A
n/a
E
D
E
D
E
3.9
24 400
1.8
3.6
Oil Filled
Oval
Ht
Total
Weight
(lbs.)
1.91x2.91
3.1
11.2
n/a
C
E
C
C
B
C
D
D
E
REFERENCE DRAWING PC2
000
200
500
0.250 Dia Thru
4 Holes
A
B
MAX
500K
4.250˝
0.250 Dia Thru
2 Holes
502K
518
3.875˝
4.375˝ 4.750˝
555K
700
718
WIRING DIAGRAMS
HID
CORE & COIL
W
Bracket
S
Wiring Diagram 18
Wiring Diagram 21
Wiring Diagram 19
277V
Cap
M
L
BRef. Dwg.
PC2
L
W
7.75” 2.75”
M
6.10”
Line
(Red)
Line
240V
208V
120V (AUX)
S
0.25”
Cap
(Red)
120V
INC LAMP
W MAX
Com
See p. 5-7 for adjustable mounting brackets and detailed bracket drawings.
Cap
(Red)
(White)
or
Com
(Yellow)
PERMISSIBLE
Com (Yellow)
or (White)
Wiring Diagram 23
Com (Yellow)
or (White)
Com
Com
(Yellow)
(Yellow)
Wiring Diagram 44
347V
277V
Cap
(Red)
120V
Com
(White)
Com
(White)
PAGE 5-24
FOR MORE INFORMATION CALL
1-800-BALLAST
(225-5278)
MH
400
• 60 Hz
• Minimum Starting
Temperature: -30° C
• CWA Designs
WATT
HID CORE & COIL BALLASTS
METAL HALIDE
Nom
Dimensions
Max Open
Circuit Watts Input Circuit Fuse Wir Ref
Input
Catalog*
Volts
Number
Type Input Current Voltage Rating Dia Dwg
A
(1) 400 WATT M59 METAL HALIDE OR H33 MERCURY LAMP
120
M400120AC4M CWA 458 4.00
300
10 18 PC2 2.0
480-120 M40048TAC4M CWA 458 1.00
300
5
19 PC2 2.0
120
4.00
10
277
M400TRIAC4M CWA 458
1.70
300
5
23 PC2 2.0
347
1.35
5
120 or
4.00
10
208 or
2.30
8
M400MLTAC4M CWA 458
300
21 PC2 2.0
240 or
2.00
5
277
1.70
5
120 or
4.00
10
208 or
2.30
8
300
21 PC2 2.0
M400MLTAC4L CWA 440
240 or
2.00
5
277
1.70
5
120 or
4.00
10
208 or
2.30
8
240 or M400ML5AC4M CWA 458
2.00
300
5
44 PC2 2.0
277 or
1.70
5
480
1.00
5
DESCRIPTION
SUFFIX *
For Ballast Only
For Bracket Only (see pg. 5-7)
For Capacitor Only (see pg. 5-5, 5-6)
For Distributor Replacement Kit
(see pg. 5-13 thru 5-15)
For Canadian Distributor
Replacement Kit (see pg. 5-16)
For Dry-Capacitor & Ballast
(see pg. 5-6)
For Distributor Ballast Lamp
Replacement Kit (see pg. 5-12)
For Bracket & Capacitor
(see pg. 5-5, 5-7)
For Bracket & Dry-Capacitor
(see pg. 5-6, 5-7)
Capacitor
Ignitor
Max
UL
Catalog Distance Bench
Number to lamp (ft) Top Rise
B
Min
Mfd Volt
Dry Film
Dia
Ht
3.9
3.9
24 400
24 400
1.8
1.8
3.6
3.6
1.91x2.91
1.91x2.91
3.1
3.1
11.2
11.2
n/a
n/a
n/a
n/a
3.9
24 400
1.8
3.6
1.91x2.91
3.1
11.2
n/a
n/a
3.9
24 360
1.8
3.6
1.91x2.91
3.1
11.2
n/a
n/a
3.9
24 400
1.8
3.6
1.91x2.91
3.1
13.0
n/a
n/a
A
n/a
E
D
E
D
E
3.9
24 400
1.8
3.6
Oil Filled
Oval
Ht
Total
Weight
(lbs.)
1.91x2.91
3.1
11.2
n/a
C
E
C
C
B
C
D
D
E
REFERENCE DRAWING PC2
000
200
500
0.250 Dia Thru
4 Holes
A
B
MAX
500K
4.250˝
0.250 Dia Thru
2 Holes
502K
518
3.875˝
4.375˝ 4.750˝
555K
700
718
WIRING DIAGRAMS
HID
CORE & COIL
W
Bracket
S
Wiring Diagram 18
Wiring Diagram 21
Wiring Diagram 19
277V
Cap
M
L
BRef. Dwg.
PC2
L
W
7.75” 2.75”
M
6.10”
Line
(Red)
Line
240V
208V
120V (AUX)
S
0.25”
Cap
(Red)
120V
INC LAMP
W MAX
Com
See p. 5-7 for adjustable mounting brackets and detailed bracket drawings.
Cap
(Red)
(White)
or
Com
(Yellow)
PERMISSIBLE
Com (Yellow)
or (White)
Wiring Diagram 23
Com (Yellow)
or (White)
Com
Com
(Yellow)
(Yellow)
Wiring Diagram 44
347V
277V
Cap
(Red)
120V
Com
(White)
Com
(White)
PAGE 5-24
FOR MORE INFORMATION CALL
1-800-BALLAST
(225-5278)
HID CORE & COIL BALLASTS
METAL HALIDE
• 60 Hz
• Minimum Starting
Temperature: -30° C
• CWA Designs
Nom
Dimensions
Max Open
Circuit Watts Input Circuit Fuse Wir Ref
Input
Catalog*
Volts
Number
Type Input Current Voltage Rating Dia Dwg
A
(1) 1000 WATT M47 METAL HALIDE OR H36 MERCURY LAMP
120
M1000120AC5M CWA 1080 9.00
425
20 18 PC3 2.8
M1000208AC5M CWA 1080 5.20
425
15 18 PC3 2.8
208
M1000240AC5M CWA 1080 4.40
425
10 18 PC3 2.8
240
277
M1000277AC5M CWA 1080 3.90
425
10 18 PC3 2.8
M1000480AC5M CWA 1080 3.30
425
10 19 PC3 2.8
480
480-120 M100048TAC5M CWA 1080 2.30
420
10 19 PC3 2.8
120 or
9.20
20
CWA 1080 4.00
420
10 23 PC3 2.8
277 or M1000TRIAC5M
347
3.20
10
120 or
9.20
20
5.30
15
208 or
21 PC3 2.8
CWA 1080
420
M1000MLTAC5M
240 or
4.60
10
277
4.00
10
120 or
9.00
20
208 or
5.20
15
240 or M1000ML5AC5M
CWA 1080 4.40
425
10 44 PC3 2.8
277 or
3.90
10
480
2.30
10
DESCRIPTION
SUFFIX *
For Ballast Only
For Bracket Only (see pg. 5-7)
For Capacitor Only (see pg. 5-5, 5-6)
For Distributor Replacement Kit
(see pg. 5-13 thru 5-15)
For Canadian Distributor
Replacement Kit (see pg. 5-16)
For Dry-Capacitor & Ballast
(see pg. 5-6)
For Bracket & Capacitor
(see pg. 5-5, 5-7)
For Bracket & Dry-Capacitor
(see pg. 5-6, 5-7)
W
Bracket
B
Dry Film
Dia
Ht
4.6
4.6
4.6
4.6
4.6
4.6
24
24
24
24
24
24
480
480
480
480
480
480
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
1.91x2.91
1.91x2.91
1.91x2.91
1.91x2.91
1.91x2.91
1.91x2.91
3.9
3.9
3.9
3.9
3.9
3.9
22.0
22.0
22.0
22.0
22.0
22.0
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
4.6
24 480
n/a
n/a
1.91x2.91
3.9
24..0
n/a
n/a
4.7
24 480
n/a
n/a
1.91x2.91
3.9
22.0
n/a
n/a
D
n/a
F
B
B
B
B
4.6
24 480
n/a
n/a
Oil Filled
Oval
Ht
Max
UL
Catalog Distance Bench
Number to lamp (ft) Top Rise
Min
Mfd Volt
1.91x2.91
3.9
22.0
n/a
D
B
B
B
B
C
E
C
C
0.250 Dia Thru
8 Holes
0.250 Dia Thru
2 Holes
4.250˝
3.875˝
4.375˝
5.375˝ 5.750˝
518
700
718
S
WIRING DIAGRAMS
Wiring Diagram 19
Line
Cap
(Red)
Wiring Diagram 21
Cap
(Red)
120V (AUX)
208V
INC LAMP
W MAX
Com
(White)
or
277V
240V
S
0.25”
Com
(Yellow)
PERMISSIBLE
Com (Yellow)
or (White)
See p. 5-7 for adjustable mounting brackets and detailed bracket drawings.
Wiring Diagram 23
Cap
(Red)
120V
Com (Yellow)
or (White)
Com
Com
(Yellow)
(Yellow)
Wiring Diagram 44
347V
277V
Cap
(Red)
120V
Com
(White)
Com
(White)
PAGE 5-25
FOR MORE INFORMATION CALL
1-800-BALLAST
(225-5278)
HID
CORE & COIL
Wiring Diagram 18
M
6.10”
Ignitor
Total
Weight
(lbs.)
A
Line
L
W
7.75” 2.75”
Capacitor
B
MAX
502K
M
L
BRef. Dwg.
PC3
WATT
REFERENCE DRAWING PC3
000
200
500
500K
MH
1000
HID CORE & COIL BALLASTS
METAL HALIDE
• 60 Hz
• Minimum Starting
Temperature: -30° C
• CWA Designs
Nom
Dimensions
Max Open
Circuit Watts Input Circuit Fuse Wir Ref
Input
Catalog*
Volts
Number
Type Input Current Voltage Rating Dia Dwg
A
(1) 1000 WATT M47 METAL HALIDE OR H36 MERCURY LAMP
120
M1000120AC5M CWA 1080 9.00
425
20 18 PC3 2.8
M1000208AC5M CWA 1080 5.20
425
15 18 PC3 2.8
208
M1000240AC5M CWA 1080 4.40
425
10 18 PC3 2.8
240
277
M1000277AC5M CWA 1080 3.90
425
10 18 PC3 2.8
M1000480AC5M CWA 1080 3.30
425
10 19 PC3 2.8
480
480-120 M100048TAC5M CWA 1080 2.30
420
10 19 PC3 2.8
120 or
9.20
20
CWA 1080 4.00
420
10 23 PC3 2.8
277 or M1000TRIAC5M
347
3.20
10
120 or
9.20
20
5.30
15
208 or
21 PC3 2.8
CWA 1080
420
M1000MLTAC5M
240 or
4.60
10
277
4.00
10
120 or
9.00
20
208 or
5.20
15
240 or M1000ML5AC5M
CWA 1080 4.40
425
10 44 PC3 2.8
277 or
3.90
10
480
2.30
10
DESCRIPTION
SUFFIX *
For Ballast Only
For Bracket Only (see pg. 5-7)
For Capacitor Only (see pg. 5-5, 5-6)
For Distributor Replacement Kit
(see pg. 5-13 thru 5-15)
For Canadian Distributor
Replacement Kit (see pg. 5-16)
For Dry-Capacitor & Ballast
(see pg. 5-6)
For Bracket & Capacitor
(see pg. 5-5, 5-7)
For Bracket & Dry-Capacitor
(see pg. 5-6, 5-7)
W
Bracket
B
Dry Film
Dia
Ht
4.6
4.6
4.6
4.6
4.6
4.6
24
24
24
24
24
24
480
480
480
480
480
480
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
1.91x2.91
1.91x2.91
1.91x2.91
1.91x2.91
1.91x2.91
1.91x2.91
3.9
3.9
3.9
3.9
3.9
3.9
22.0
22.0
22.0
22.0
22.0
22.0
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
4.6
24 480
n/a
n/a
1.91x2.91
3.9
24..0
n/a
n/a
4.7
24 480
n/a
n/a
1.91x2.91
3.9
22.0
n/a
n/a
D
n/a
F
B
B
B
B
4.6
24 480
n/a
n/a
Oil Filled
Oval
Ht
Max
UL
Catalog Distance Bench
Number to lamp (ft) Top Rise
Min
Mfd Volt
1.91x2.91
3.9
22.0
n/a
D
B
B
B
B
C
E
C
C
0.250 Dia Thru
8 Holes
0.250 Dia Thru
2 Holes
4.250˝
3.875˝
4.375˝
5.375˝ 5.750˝
518
700
718
S
WIRING DIAGRAMS
Wiring Diagram 19
Line
Cap
(Red)
Wiring Diagram 21
Cap
(Red)
120V (AUX)
208V
INC LAMP
W MAX
Com
(White)
or
277V
240V
S
0.25”
Com
(Yellow)
PERMISSIBLE
Com (Yellow)
or (White)
See p. 5-7 for adjustable mounting brackets and detailed bracket drawings.
Wiring Diagram 23
Cap
(Red)
120V
Com (Yellow)
or (White)
Com
Com
(Yellow)
(Yellow)
Wiring Diagram 44
347V
277V
Cap
(Red)
120V
Com
(White)
Com
(White)
PAGE 5-25
FOR MORE INFORMATION CALL
1-800-BALLAST
(225-5278)
HID
CORE & COIL
Wiring Diagram 18
M
6.10”
Ignitor
Total
Weight
(lbs.)
A
Line
L
W
7.75” 2.75”
Capacitor
B
MAX
502K
M
L
BRef. Dwg.
PC3
WATT
REFERENCE DRAWING PC3
000
200
500
500K
MH
1000
MH
1500
HID CORE & COIL BALLASTS
• 60 Hz
• Minimum Starting
Temperature: -30° C
• CWA Designs
WATT
METAL HALIDE
Nom
Dimensions
Max Open
Input
Catalog*
Circuit Watts Input Circuit Fuse Wir Ref
Volts
Number
Type Input Current Voltage Rating Dia Dwg
A
(1) 1500 WATT M48 METAL HALIDE LAMP
480-120 M150048TAC5M CWA 1610 3.50
450
10 19 PC3 4.3
120 or
14.00
40
277 or M1500TRIAC5M CWA 1610 6.00
450
20 23 PC3 4.3
347
4.50
15
120 or
14.00
40
208 or M1500MLTAC5M CWA 1610 8.00
25 21 PC3 4.3
450
240 or
7.00
20
277
6.00
20
480
M1500480AC5M CWA 1610 3.50
450
10 19 PC3 4.3
DESCRIPTION
Ignitor
Oil Filled
Oval
Ht
Total
Weight
(lbs.)
Max
UL
Catalog Distance Bench
Number to lamp (ft) Top Rise
B
Min
Mfd Volt
Dry Film
Dia
Ht
6.4
32 525
n/a
n/a
1.97x3.66
3.9
29.5
n/a
n/a
E
6.4
32 500
n/a
n/a
1.97x3.66
3.9
29.5
n/a
n/a
G
6.4
32 525
n/a
n/a
1.97x3.66
3.9
30.0
n/a
n/a
6.3
32 525
n/a
n/a
1.97x3.66
3.9
29.5
n/a
n/a
F
E
F
F
E
SUFFIX *
For Ballast Only
For Bracket Only (see pg. 5-7)
For Capacitor Only (see pg. 5-5, 5-6)
For Distributor Replacement Kit
(see pg. 5-13 thru 5-15)
For Canadian Distributor
Replacement Kit (see pg. 5-16)
For Dry-Capacitor & Ballast
(see pg. 5-6)
For Bracket & Capacitor
(see pg. 5-5, 5-7)
For Bracket & Dry-Capacitor
(see pg. 5-6, 5-7)
HID
CORE & COIL
Capacitor
000
200
500
REFERENCE DRAWING PC3
0.250 Dia Thru
8 Holes
A
B
MAX
500K
502K
0.250 Dia Thru
2 Holes
518
4.250˝
700
3.875˝
4.375˝
5.375˝ 5.750˝
718
WIRING DIAGRAMS
W
Bracket
S
M
L
BRef. Dwg.
PC3
L
W
7.75” 2.75”
Wiring Diagram 19
Line
Wiring Diagram 21
Wiring Diagram 23
277V
Cap
(Red)
347V
240V
M
6.10”
S
0.25”
See p. 5-7 for adjustable mounting brackets and detailed bracket drawings.
120V (AUX)
208V
INC LAMP
W MAX
277V
Cap
(Red)
120V
PERMISSIBLE
Com (Yellow)
Com (Yellow)
or (White)
or (White)
Com
(Yellow)
PAGE 5-26
Cap
(Red)
120V
Com
(Yellow)
Com
Com
(White)
(White)
FOR MORE INFORMATION CALL
1-800-BALLAST
(225-5278)
M1000MLTAC5M
1000W
Metal Halide
60Hz CWA
Specification Sheet
120
208
240
277
±10%
±10%
±10%
±10%
±10%
Lamp Watts
±10%
±10%
±10%
±10%
±10%
Power Factor (min)
90%
90%
90%
90%
90%
1080 W
1080 W
1080 W
1080 W
1080 W
425 V
425 V
425 V
425 V
425 V
8.95
5.15
4.50
3.90
Input Volts
Regulation
Line Volts
Input Watts
NOM. Open Circuit Voltage
Line Current (Amps)
Operating
M47 / H36
277 V ( BLACK)
CAP
(RED)
240 V ( VIOLET)
208 V ( ORANGE)
120 V ( BLK/ YEL)
Open Circuit
5.65
3.25
2.80
2.45
Starting
6.20
3.60
3.10
2.70
Recommended Fuse (Amps)
20
15
10
10
0
Lamp Dropout Voltage (Line)
75 V
130 V
150 V
170 V
V
COM ( YEL)
UL Temperature Ratings
Insulation Class
COM ( YEL)
Wiring Diagram
H (180°C) H (180°C) H (180°C) H (180°C) H (180°C)
A
D
D
D
D
-22°F -30°C
-22°F -30°C
-22°F -30°C
-22°F -30°C
-22°F -30°C
24.0 uf
24.0 uf
24.0 uf
24.0 uf
24.0 uf
480 V
480 V
480 V
480 V
480 V
2000 V
2000 V
2000 V
2000 V
2000 V
High Potential Test 1 Second
2500 V
2500 V
2500 V
2500 V
2500 V
Secondary Open Ckt Voltage (V)
380 - 465
380 - 465
380 - 465
380 - 465
380 - 465
Secondary Current Shorted (A)
4.90 - 6.05
4.90 - 6.05
4.90 - 6.05
4.90 - 6.05
4.90 - 6.05
Input Operating Current (A)
8.15 - 10.00 4.45 - 5.50
4.05 - 5.00
3.50 - 4.35
-
Input Open Circuit Current (A)
2.90 - 8.15
1.60 - 4.55
1.45 - 4.15
1.25 - 3.65
-
Input Short Circuit Current (A)
4.85 - 7.35
2.90 - 4.40
2.40 - 3.65
2.10 - 3.20
-
Rated Temp
90 °C
2.90 in
2.90 in
2.90 in
2.90 in
2.90 in
Height:
3.90 in
Dimension B
5.05 in
5.05 in
5.05 in
5.05 in
5.05 in
Width / Diameter:
2.91 in
Weight
22.0 lbs
22.0 lbs
22.0 lbs
22.0 lbs
22.0 lbs
Lead Lengths (inches)
Coil Material (Pri. / Sec.):
12-14
12-14
12-14
12-14
12-14
Cu / Al
Cu / Al
Cu / Al
Cu / Al
Cu / Al
Temperature Code
MIN. Starting Temperature
CAPACITOR Specifications
Microfarads
Volts (min.)
60Hz Test Procedures
High Potential Test 1 Minute
Core and Coil Specifications
Dimension A
Document #:
010-11022-02
Date:
2/16/2006
Status:
Production
Replaces Catalog #:
M1000MLTAC5M
LAMP
(RED/BLK)
0.250 Dia Thru
8 Holes
B
MAX
4.250"
0.250 Dia Thru
2 Holes
3.875"
4.375"
5.375"
5.750"
Reference Drawing
Capacitor: 005-2779-MF
Ignitor: None
This Ballast
does not
require a
Ignitor
For alternate capacitor construction consult sales
Data is based upon tests performed by Universal Lighting Technologies in a controled environment and is representive of relative performance.
Actual performance may vary depending on operating conditions. Specifications are subject to change without notice.
3/29/2006
Universal Lighting Technologies
26 Century Blvd. Suite 500 - Nashville, TN 37214
Phone 1-800-225-5278 Fax 1-800-206-0035
www.universalballast.com
M1500MLTAC5M
1500W
Metal Halide
60Hz CWA
Specification Sheet
120
208
240
277
±10%
±10%
±10%
±10%
±10%
Lamp Watts
±10%
±10%
±10%
±10%
±10%
Power Factor (min)
90%
90%
90%
90%
90%
1615 W
1615 W
1615 W
1615 W
1615 W
455 V
455 V
455 V
455 V
455 V
14.30
8.30
7.20
6.20
Input Volts
Regulation
Line Volts
Input Watts
NOM. Open Circuit Voltage
Line Current (Amps)
Operating
M48
277 V ( BLACK)
CAP
(RED)
240 V ( VIOLET)
208 V ( ORANGE)
120 V ( BLK/ YEL)
Open Circuit
9.40
5.40
4.70
4.05
Starting
6.35
3.65
3.20
2.75
Recommended Fuse (Amps)
40
25
20
20
0
Lamp Dropout Voltage (Line)
70 V
120 V
140 V
160 V
V
COM ( YEL)
UL Temperature Ratings
Insulation Class
COM ( YEL)
Wiring Diagram
H (180°C) H (180°C) H (180°C) H (180°C) H (180°C)
A
F
G
F
E
-22°F -30°C
-22°F -30°C
-22°F -30°C
-22°F -30°C
-22°F -30°C
32.0 uf
32.0 uf
32.0 uf
32.0 uf
32.0 uf
525 V
525 V
525 V
525 V
525 V
2000 V
2000 V
2000 V
2000 V
2000 V
High Potential Test 1 Second
2500 V
2500 V
2500 V
2500 V
2500 V
Secondary Open Ckt Voltage (V)
405 - 495
405 - 495
405 - 495
405 - 495
405 - 495
Secondary Current Shorted (A)
7.45 - 9.15
7.45 - 9.15
7.45 - 9.15
7.45 - 9.15
7.45 - 9.15
Input Operating Current (A)
12.60 - 15.40 7.80 - 9.60
6.30 - 7.75
5.50 - 6.80
-
Input Open Circuit Current (A)
4.65 - 13.65 2.70 - 7.90
2.30 - 6.85
2.00 - 5.95
-
Input Short Circuit Current (A)
4.85 - 7.30
2.10 - 3.25
2.40 - 3.65
2.10 - 3.25
-
Rated Temp
90 °C
4.40 in
4.40 in
4.40 in
4.40 in
4.40 in
Height:
3.88 in
Dimension B
6.40 in
6.40 in
6.40 in
6.40 in
6.40 in
Width / Diameter:
2.91 in
Weight
30.0 lbs
30.0 lbs
30.0 lbs
30.0 lbs
30.0 lbs
Lead Lengths (inches)
Coil Material (Pri. / Sec.):
12-14
12-14
12-14
12-14
12-14
Cu / Cu
Cu / Cu
Cu / Cu
Cu / Cu
Cu / Cu
Temperature Code
MIN. Starting Temperature
CAPACITOR Specifications
Microfarads
Volts (min.)
60Hz Test Procedures
High Potential Test 1 Minute
Core and Coil Specifications
Dimension A
Document #:
010-11756-00
Date:
5/8/2006
Status:
Production
Replaces Catalog #:
1130-99R
LAMP
(RED/BLK)
0.250 Dia Thru
8 Holes
B
MAX
4.250"
0.250 Dia Thru
2 Holes
3.875"
4.375"
5.375"
5.750"
Reference Drawing
Capacitor: 005-1474-MF
Ignitor: None
This Ballast
does not
require a
Ignitor
For alternate capacitor construction consult sales
Data is based upon tests performed by Universal Lighting Technologies in a controled environment and is representive of relative performance.
Actual performance may vary depending on operating conditions. Specifications are subject to change without notice.
4/21/2006
Universal Lighting Technologies
26 Century Blvd. Suite 500 - Nashville, TN 37214
Phone 1-800-225-5278 Fax 1-800-206-0035
www.universalballast.com
M175MLTAC3M
175W
Metal Halide
60Hz CWA
Specification Sheet
120
208
240
277
±10%
±10%
±10%
±10%
±10%
Lamp Watts
±10%
±10%
±10%
±10%
±10%
Power Factor (min)
90%
90%
90%
90%
90%
213 W
213 W
213 W
213 W
213 W
305 V
305 V
305 V
305 V
305 V
1.90
1.10
0.95
0.85
Input Volts
Regulation
Line Volts
Input Watts
NOM. Open Circuit Voltage
Line Current (Amps)
Operating
M57 / M107 / H39
277 V ( BLACK)
CAP
(RED)
240 V ( VIOLET)
208 V ( ORANGE)
120 V ( BLK/ YEL)
Open Circuit
1.70
0.95
0.85
0.70
Starting
1.40
0.80
0.70
0.60
Recommended Fuse (Amps)
5
3
3
2
0
Lamp Dropout Voltage (Line)
60 V
100 V
120 V
135 V
V
COM ( YEL)
UL Temperature Ratings
Insulation Class
Temperature Code
MIN. Starting Temperature
COM ( YEL)
Wiring Diagram
H (180°C) H (180°C) H (180°C) H (180°C) H (180°C)
A
C
B
C
-22°F -30°C
-22°F -30°C
-22°F -30°C
-22°F -30°C
A
10 uf
10 uf
10 uf
10 uf
10 uf
400 V
400 V
400 V
400 V
400 V
60Hz Test Procedures
High Potential Test 1 Minute
2000 V
2000 V
2000 V
2000 V
2000 V
High Potential Test 1 Second
2500 V
2500 V
2500 V
2500 V
2500 V
Secondary Open Ckt Voltage (V)
275 - 335
275 - 335
275 - 335
275 - 335
275 - 335
Secondary Current Shorted (A)
1.55 - 1.90
1.55 - 1.90
1.55 - 1.90
1.55 - 1.90
1.55 - 1.90
Input Operating Current (A)
1.70 - 2.20
1.00 - 1.25
0.85 - 1.10
0.75 - 0.95
-
Input Open Circuit Current (A)
0.80 - 2.45
0.45 - 1.40
0.40 - 1.25
0.35 - 1.05
-
Input Short Circuit Current (A)
1.05 - 1.60
0.60 - 0.90
0.50 - 0.80
0.45 - 0.70
-
Temp Rating:
90 °C
2.20 in
2.20 in
2.20 in
2.20 in
2.20 in
Height:
2.69 in
Dimension B
3.60 in
3.60 in
3.60 in
3.60 in
3.60 in
Width / Diameter:
2.69 in
Weight
6.10 lbs
6.10 lbs
6.10 lbs
6.10 lbs
6.10 lbs
Lead Lengths (inches)
Coil Material (Pri. / Sec.):
12-14
12-14
12-14
12-14
12-14
Cu / Al
Cu / Al
Cu / Al
Cu / Al
Cu / Al
Document #:
010-10883-03
Date:
1/18/2007
Status:
Production
Replaces Catalog #:
New Design
0.234 Dia Thru
4 Holes
B
MAX
-22°F -30°C
CAPACITOR Specifications
Microfarads
Volts (min.)
Core and Coil Specifications
Dimension A
LAMP
(RED/BLK)
2.812"
0.250 Dia Thru
2 Holes
2.438"
3.500"
3.938"
Reference Drawing
Capacitor: 005-1184-MF
Ignitor: None
This Ballast
does not
require a
Ignitor
For alternate capacitor construction consult sales
Data is based upon tests performed by Universal Lighting Technologies in a controled environment and is representive of relative performance.
Actual performance may vary depending on operating conditions. Specifications are subject to change without notice.
1/17/2007
Universal Lighting Technologies
26 Century Blvd. Suite 500 - Nashville, TN 37214
Phone 1-800-225-5278 Fax 1-800-206-0035
www.universalballast.com
Specification Sheet
Catalog Number: M250MLTAC3M
Document #: 010-9652- 03
Date: 5/6/2004
Lamp Type
ANSI Designation
Line Voltage
Regulation
Frequency
Recommended Fuse
Circuit Type
Insulation Class
Capacitor Value
Capacitor Volt Rating
Capacitor Temp Rating
Capacitor Part Number
Lamp Starter
Winding Material (Pri/Sec)
FEATURES:
Line
Volt
120
208
240
277
250W METAL HALIDE
250W MH
M58 or H37
120/208/240/277
10%
60 HZ
8/5/4/3
CWA
180° C
15MF
400 VOLTS
90° C
005-1185-MF
N/A
Cu/Al
Replaces Catalog #
Samples Available
Production Available
Agency Certification
Maximum Distance to Lamp
1130-92
Yes
Yes
UL & CSA
N/A
Utilizes Precise-Wound Coils
Electrical Characteristics
Line Current in Amps
Open
Power
Input
Circuit
Factor Oprtng
Open
Start
Watts
Volts
High
2.65
2.50
1.88
297
315
High
1.50
1.58
1.15
297
315
High
1.30
1.25
0.95
297
315
High
1.13
1.10
0.86
297
315
Drop
Out
Volts
65
105
125
150
Min.
Start
Temp.
-30°C
-30°C
-30°C
-30°C
UL
Temp.
Code
D
D
D
D
Reference Drawing
Line
Volt
120
208
240
277
Power
Factor
High
High
High
High
Test Limits
Line Current, Amps
Open Circuit
Operating
Open
Short
Voltage (V)
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
2.41
2.94
1.25
3.58
1.42
2.40
288
350
1.37
1.67
0.79
2.26
0.84
1.42
288
350
1.18
1.44
0.63
1.79
0.74
1.24
288
350
1.03
1.25
0.55
1.57
0.56
0.95
288
350
Physical Characteristics
Mounting Holes (In.)
Overall Dimensions, Inches
Length
3.94
Height
2.81
Stack
3.00
Over
Coils
4.25
Diam
0.25
Length
3.50
Width
2.44
Bracket
CapacitorDim.
Mntng Dim
Length Width
Dia.
Length
1.91
2.69
Application and Performance Specification Information Subject to Change without Notification.
For samples, contact your Universal Lighting Technologies Representative.
1-800-BALLAST
Short Circuit
Current (A)
Min.
Max.
2.24
2.85
2.24
2.85
2.24
2.85
2.24
2.85
www.universalballast.com
Ballast
Net
Weight
9.00
Lead
Length
Inches
12-14
MERCURY
100
WATT
Nom
Dimensions
Max Open
Input
Catalog*
Circuit Watts Input Circuit Fuse Wir Ref
Volts
Number
Type Input Current Voltage Rating Dia Dwg
A
(1) 100 WATT H38 OR H44 MERCURY LAMP
480-120 H10048TAC3M
CWA 124
0.28
240
1
19 PC1
1.3
120 or
1.05
3
208 or
0.60
2
21 PC1
1.3
CWA 125
250
H100MLTAC3M
240 or
0.52
2
277
0.45
2
120 or
1.08
3
CWA 120 0.45
240
2
23 PC1 1.4
277 or H100TRIAC3M
347
0.36
1
DESCRIPTION
MERCURY
Capacitor
Min
Mfd Volt
B
Ignitor
Dry Film
Dia
Ht
Oil Filled
Oval
Ht
Total
Weight
(lbs.)
Max
UL
Catalog Distance Bench
Number to lamp (ft) Top Rise
2.5
10
280
1.4
2.7
1.31x2.16
2.7
4.0
n/a
n/a
A
2.5
10
280
1.4
2.7
1.31x2.16
2.7
4.0
n/a
n/a
A
2.7
10 280
1.2
2.7
1.31x2.16
2.7
3.7
n/a
n/a
A
SUFFIX *
For Ballast Only
For Bracket Only (see pg. 5-7)
For Capacitor Only (see pg. 5-5, 5-6)
For Distributor Replacement Kit
(see pg. 5-13 thru 5-15)
For Canadian Distributor
Replacement Kit (see pg. 5-16)
For Dry-Capacitor & Ballast
(see pg. 5-6)
For Bracket & Capacitor
(see pg. 5-5, 5-7)
For Bracket & Dry-Capacitor
(see pg. 5-6, 5-7)
HID
CORE & COIL
HID CORE & COIL BALLASTS
• 60 Hz
• Minimum Starting
Temperature: -30° C
• CWA, Normal and High Power
Factor models available
000
200
500
REFERENCE DRAWING PC1
0.199 Dia Thru
4 Holes
A
B
MAX
500K
2.812˝
502K
0.250 Dia Thru
2 Holes
518
2.438˝
700
3.500˝ 3.938˝
718
WIRING DIAGRAMS
Wiring Diagram 19
W
Bracket
S
L
W
5.25” 1.25”
Wiring Diagram 23
Wiring Diagram 21
Cap
(Red)
277V
347V
240V
M
L
BRef. Dwg.
PC1
Line
277V
120V (AUX)
208V
INC LAMP
W MAX
M
4.60”
S
0.25”
PERMISSIBLE
Com (Yellow)
or (White)
Cap
(Red)
120V
Cap
(Red)
120V
Com (Yellow)
or (White)
Com
(Yellow)
Com
(Yellow)
Com
(White)
Com
(White)
See p. 5-7 for adjustable mounting brackets and detailed bracket drawings.
PAGE 5-42
FOR MORE INFORMATION CALL
1-800-BALLAST
(225-5278)
HID CORE & COIL BALLASTS
MERCURY
Input
Volts
Catalog*
Number
240
277
244
(1) 175 WATT H39 MERCURY LAMP
R-NPF
2.05
240
192
1033-23S 9
R-HPF 3
1.08
R-NPF
1.90
277
192
1033-15S 9
R-HPF 3
1.25
480-120 H17548TAC3M
CWA 205
0.75
120 or
1.75
1.00
208 or
CWA 202
H175MLTAC3M
240 or
0.86
277
0.75
120 or
1.90
277 or H175TRIAC3M
CWA 205 0.80
347
0.64
3
9
• 60 Hz
• Minimum starting
temperature: -30° C
• CWA design or reactor
models available
Nom
Dimensions
Max Open
Circuit Watts Input Circuit Fuse Wir Ref
Type Input Current Voltage Rating Dia Dwg
A
B
(1) 125 WATT H42 MERCURY LAMP
R-NPF
1.65
240
139
1033-113S
R-HPF 3
0.90
R-NPF
1.55
277
141
1033-111S
R-HPF 3
1.05
120 or
1.45
0.85
208 or
CWA 160
H125MLTAC3M
240 or
0.70
277
0.62
240
277
243
235
255
5
3
5
3
5
3
3
2
8
5
8
5
2
5
3
3
2
5
2
2
MERCURY
125-175
WATT
Capacitor
Min
Mfd Volt
Ignitor
Dry Film
Dia
Ht
Oil Filled
Oval
Ht
n/a
1.6
n/a
1.6
n/a
2.7
n/a
2.7
n/a
1.31x2.16
n/a
1.31x2.16
n/a
3.1
n/a
3.1
1.6
2.7
1.31x2.16
3.1
17.5 300
n/a
1.6
n/a
1.6
1.6
n/a
2.7
n/a
2.7
3.6
n/a
1.31x2.16
n/a
1.31x2.16
1.56x2.69
n/a
3.1
n/a
3.1
3.1
2.9
17.5 300
1.6
3.6
1.56x2.69
3.0
17.5 240
1.6
2.7
1.56x2.69
24
1
1.5
2.5
10
240
24
1
1.5
2.5
10
277
21 PC1
3.0
5.0
13 280
24
1
2.2
3.3
12
240
24
1
2.2
3.3
12
277
19 PC1
1.8
3.0
21 PC1
1.6
23 PC1
1.8
Total
Weight
(lbs.)
Max
UL
Catalog Distance Bench
Number to lamp (ft) Top Rise
2.4
n/a
n/a
A
2.4
n/a
n/a
D
4.0
n/a
n/a
B
3.5
n/a
n/a
A
3.5
n/a
n/a
B
5.2
n/a
n/a
A
3.1
5.2
n/a
n/a
A
3.1
5.3
n/a
n/a
C
Capacitors are available as an option for high power factor operation.
Also can be used to operate (1) 150 watt S63 High Pressure Sodium
lamp. Electrical characteristics will vary from those shown.
REFERENCE DRAWING 1
REFERENCE DRAWING PC1
0.438"
DESCRIPTION
000
200
500
B
MAX
2.812˝
0.250 Dia Thru
2 Holes
1.750"
2.188"
500K
2.188"
2.438˝
502K
WIRING DIAGRAMS
Wiring Diagram 19
Wiring Diagram 21
700
277V
Line
Cap
(Red)
240V
718
120V (AUX)
208V
L
W
4.00” 0.75”
5.25” 1.25”
Cap
(Red)
120V
Com (Yellow)
or (White)
Com
(Yellow)
S
Com
(Yellow)
Wiring Diagram 24
Wiring Diagram 23
M
L
BRef. Dwg.
1
PC1
HID
CORE & COIL
518
PERMISSIBLE
Com (Yellow)
or (White)
W
3.500˝ 3.938˝
2.625"
INC LAMP
W MAX
Bracket
A
0.594"
SUFFIX *
For Ballast Only
For Bracket Only (see pg. 5-7)
For Capacitor Only (see pg. 5-5, 5-6)
For Distributor Replacement Kit
(see pg. 5-13 thru 5-15)
For Canadian Distributor
Replacement Kit (see pg. 5-16)
For Dry-Capacitor & Ballast
(see pg. 5-6)
For Bracket & Capacitor
(see pg. 5-5, 5-7)
For Bracket & Dry-Capacitor
(see pg. 5-6, 5-7)
0.199 Dia Thru
4 Holes
B
A
.203" Dia Thru
4 Holes
347V
M
3.35”
4.60”
S
0.25”
0.25”
Line
277V
Lamp
(Blue)
Cap
(Red)
120V
See p. 5-7 for adjustable mounting brackets and detailed bracket drawings.
Com
Com
(White)
Com
(White)
PAGE 5-43
FOR MORE INFORMATION CALL
1-800-BALLAST
(225-5278)
MERCURY
250
• 60 HZ
• Minimum Starting
Temperature: -30° C
• Normal and High Power Factor,
CWA designs
WATT
Nom
Dimensions
Max Open
Input
Catalog*
Circuit Watts Input Circuit Fuse Wir Ref
Volts
Number
Type Input Current Voltage Rating Dia Dwg
A
(1) 250 WATT H37 MERCURY LAMP
R-NPF
2.85
10
240
240
24 4
1.5
1033-24S 10
1.85
5
R-HPF 3 270
R-NPF
2.70
10
10
277
277
24 4
1.5
1033-16S
1.60
5
R-HPF 3 270
CWA 285
0.66
255
3
19 PC1
2.3
480-120 H25048TAC3M
120 or
2.55
8
1.50
5
208 or
21 PC1
2.3
CWA 275
250
240 or H250MLTAC3M
1.27
5
277
1.10
3
120 or
2.60
8
277 or H250TRIAC3M
CWA 285 1.20
260
5
23 PC1 2.3
347
1.00
3
HID CORE & COIL BALLASTS
MERCURY
Capacitor
B
Min
Mfd Volt
Dry Film
Dia
Ht
3.0
17.5 240
1.6
3.6
Ignitor
Oil Filled
Oval
Ht
1.56x2.69
Total
Weight
(lbs.)
3.1
5.5
Max
UL
Catalog Distance Bench
Number to lamp (ft) Top Rise
n/a
n/a
A
3.0
17.5 277
1.6
3.6
1.56x2.69
3.1
5.5
n/a
n/a
A
3.5
22.5 280
1.6
3.6
1.56x2.69
3.5
6.7
n/a
n/a
E
3.5
22.5 280
1.6
3.6
1.56x2.69
3.50
6.7
n/a
n/a
D
3.5
22.5 280
1.6
3.6
1.56x2.69
3.5
6.7
n/a
n/a
B
Capacitors are available as an option for high power
factor operation.
Also can be used to operate (1) 215 watt S65 High
Pressure Sodium lamp.
Electrical characteristics will vary from those shown.
3
10
REFERENCE DRAWING PC1
DESCRIPTION
SUFFIX *
For Ballast Only
For Bracket Only (see pg. 5-7)
For Capacitor Only (see pg. 5-5, 5-6)
For Distributor Replacement Kit
(see pg. 5-13 thru 5-15)
For Canadian Distributor
Replacement Kit (see pg. 5-16)
For Dry-Capacitor & Ballast
(see pg. 5-6)
For Bracket & Capacitor
(see pg. 5-5, 5-7)
For Bracket & Dry-Capacitor
(see pg. 5-6, 5-7)
000
200
500
REFERENCE DRAWING 4
0.656"
.218" Dia Thru
4 Holes
0.199 Dia Thru
4 Holes
A
A
B
0.843"
B
MAX
2.812˝
0.250 Dia Thru
2 Holes
2.937"
500K
2.500"
502K
2.438˝
3.500˝ 3.938˝
3.125"
3.125"
3.750"
518
700
WIRING DIAGRAMS
718
Wiring Diagram 19
Wiring Diagram 21
HID
CORE & COIL
277V
Line
Cap
(Red)
240V
120V (AUX)
W
Bracket
S
L
W
5.25” 1.25”
Com (Yellow)
or (White)
Com
(Yellow)
M
4.60”
S
0.25”
Cap
(Red)
120V
PERMISSIBLE
Com (Yellow)
or (White)
M
L
BRef. Dwg.
PC1, 4
208V
INC LAMP
W MAX
Com
(Yellow)
Wiring Diagram 24
Wiring Diagram 23
347V
See p. 5-7 for adjustable mounting brackets and detailed bracket drawings.
Line
277V
Lamp
(Blue)
Cap
(Red)
120V
Com
Com
Com
(White)
(White)
PAGE 5-44
FOR MORE INFORMATION CALL
1-800-BALLAST
(225-5278)
HID CORE & COIL BALLASTS
• 60 Hz
• Minimum starting
temperature: -30° C
• CWA, Normal and High Power
Factor models available
MERCURY
Nom
Dimensions
Max Open
Input
Catalog*
Circuit Watts Input Circuit Fuse Wir Ref
Volts
Number
Type Input Current Voltage Rating Dia Dwg
A
(1) 400 WATT H33 MERCURY LAMP
R-NPF
4.60
10
240
430
240
24 4
1.7
1033-25S 11
R-HPF 3
2.60
5
R-NPF
4.25
10
277
430
277
24 4
1.7
1033-17S 11
R-HPF 3
2.40
5
480-120 H40048TAC4M
CWA 458 1.05
245
5
19 PC2 1.6
120
H400120AC4M
CWA 458 1.05
245
5
18 PC2 1.6
120 or
3.90
10
277 or H400TRIAC4M
CWA 440 2.22
260
5
23 PC2 1.8
347
1.92
5
120 or
3.90
10
208 or
2.22
8
CWA 440
245
21 PC2
1.6
H400MLTAC4M
240 or
1.92
5
277
1.68
5
(1) 1000 WATT H36 MERCURY LAMP
480-120 H100048TAC5M
CWA 1080 2.28
440
10 19 PC3 2.9
120 or
9.30
20
5.30
15
208 or
21 PC3 2.9
430
H1000MLTAC5M CWA 1080
240 or
4.50
10
277
4.00
10
3
10
MERCURY
400-1000
WATT
Capacitor
Ignitor
Oil Filled
Oval
Ht
Total
Weight
(lbs.)
Max
UL
Catalog Distance Bench
Number to lamp (ft) Top Rise
B
Min
Mfd Volt
Dry Film
Dia
Ht
3.2
22.5 240
1.5
3.6
1.56x2.69
3.5
6.1
n/a
n/a
B
3.2
22.5 277
1.5
3.6
1.56x2.69
3.5
6.1
n/a
n/a
C
3.4
3.4
35 240
35 240
1.6
1.8
3.6
3.6
1.91x2.91
1.91x2.91
3.1
3.1
9.5
9.5
n/a
n/a
n/a
n/a
C
C
3.5
35 240
1.8
3.6
1.91x2.91
3.1
9.5
n/a
n/a
A
3.4
35
240
1.6
3.6
1.91x2.91
3.1
9.5
n/a
n/a
C
4.7
24 480
1.8
3.6
1.91x2.91
3.9
19.5
n/a
n/a
4.7
24 480
n/a
n/a
1.91x2.91
3.9
19.5
n/a
n/a
C
B
A
B
B
Capacitors are available as an option for high power
factor operation.
Also can be used to operate (1) 215 watt S65 High Pressure Sodium lamp.
Electrical characteristics will vary from those shown.
DESCRIPTION
SUFFIX *
For Ballast Only
For Bracket Only (see pg. 5-7)
For Capacitor Only (see pg. 5-5, 5-6)
For Distributor Replacement Kit
(see pg. 5-13 thru 5-15)
For Canadian Distributor
Replacement Kit (see pg. 5-16)
For Dry-Capacitor & Ballast
(see pg. 5-6)
For Bracket & Capacitor
(see pg. 5-5, 5-7)
For Bracket & Dry-Capacitor
(see pg. 5-6, 5-7)
REFERENCE DRAWING PC2
000
200
500
A
B
0.843"
4.250˝
500K
0.250 Dia Thru
2 Holes
0.250 Dia Thru
2 Holes
2.937"
502K
3.875˝
4.375˝ 4.750˝
518
4.250˝
3.875˝
2.500"
4.375˝
5.375˝ 5.750˝
3.125"
3.125"
3.750"
700
WIRING DIAGRAMS
S
Wiring Diagram 19
Line
Cap
(Red)
Line
Wiring Diagram 21
Cap
(Red)
M
L
S
0.25”
0.25”
0.25”
See p. 5-7 for adjustable mounting brackets and detailed bracket drawings.
Com
(White)
or
Com
(Yellow)
Wiring Diagram 23
240V
208V
Cap
(Red)
120V
INC LAMP
W MAX
M
5.75”
6.10”
4.60”
277V
PERMISSIBLE
Com (Yellow)
Com (Yellow)
or (White)
or (White)
Com
(Yellow)
Com
(Yellow)
Wiring Diagram 24
347V
Line
277V
Lamp
(Blue)
Cap
(Red)
120V
Com
Com
(White)
Com
(White)
PAGE 5-45
FOR MORE INFORMATION CALL
1-800-BALLAST
(225-5278)
HID
CORE & COIL
718
Bracket
L
W
7.75” 1.25”
7.75” 2.75”
5.25” 1.25”
0.656"
.218" Dia Thru
4 Holes
A
B
MAX
120V (AUX)
BRef. Dwg.
PC2
PC3
4
REFERENCE DRAWING 4
0.250 Dia Thru
8 Holes
0.250 Dia Thru
4 Holes
A
B
MAX
Wiring Diagram 18
W
REFERENCE DRAWING PC3
HID CORE & COIL BALLASTS
MERCURY
Nom
Dimensions
Max Open
Input
Catalog*
Circuit Watts Input Circuit Fuse Wir Ref
Volts
Number
Type Input Current Voltage Rating Dia Dwg
A
(1) 400 WATT H33 MERCURY LAMP
R-NPF
4.60
10
240
430
240
24 4
1.7
1033-25S 11
2.60
5
R-HPF 3
R-NPF
4.25
10
430
277
24 4
1.7
277
1033-17S 11
2.40
5
R-HPF 3
480-120 H40048TAC4M
CWA 458 1.05
245
5
19 PC2 1.6
120
H400120AC4M
CWA 458 1.05
245
5
18 PC2 1.6
120 or
3.90
10
CWA 440 2.22
260
5
23 PC2 1.8
277 or H400TRIAC4M
347
1.92
5
120 or
3.90
10
208 or
2.22
8
CWA 440
245
21 PC2
1.6
H400MLTAC4M
240 or
1.92
5
277
1.68
5
(1) 1000 WATT H36 MERCURY LAMP
480-120 H100048TAC5M
CWA 1080 2.28
440
10 19 PC3 2.9
120 or
9.30
20
5.30
15
208 or
21 PC3 2.9
430
H1000MLTAC5M CWA 1080
240 or
4.50
10
277
4.00
10
3
10
MERCURY
400-1000
• 60 Hz
• Minimum starting
temperature: -30° C
• CWA, Normal and High Power
Factor models available
WATT
Capacitor
Ignitor
Oil Filled
Oval
Ht
Total
Weight
(lbs.)
Max
UL
Catalog Distance Bench
Number to lamp (ft) Top Rise
B
Min
Mfd Volt
Dry Film
Dia
Ht
3.2
22.5 240
1.5
3.6
1.56x2.69
3.5
6.1
n/a
n/a
B
3.2
22.5 277
1.5
3.6
1.56x2.69
3.5
6.1
n/a
n/a
C
3.4
3.4
35 240
35 240
1.6
1.8
3.6
3.6
1.91x2.91
1.91x2.91
3.1
3.1
9.5
9.5
n/a
n/a
n/a
n/a
C
C
3.5
35 240
1.8
3.6
1.91x2.91
3.1
9.5
n/a
n/a
A
3.4
35
240
1.6
3.6
1.91x2.91
3.1
9.5
n/a
n/a
C
4.7
24 480
1.8
3.6
1.91x2.91
3.9
19.5
n/a
n/a
4.7
24 480
n/a
n/a
1.91x2.91
3.9
19.5
n/a
n/a
C
B
A
B
B
Capacitors are available as an option for high power
factor operation.
Also can be used to operate (1) 215 watt S65 High Pressure Sodium lamp.
Electrical characteristics will vary from those shown.
DESCRIPTION
SUFFIX *
For Ballast Only
For Bracket Only (see pg. 5-7)
For Capacitor Only (see pg. 5-5, 5-6)
For Distributor Replacement Kit
(see pg. 5-13 thru 5-15)
For Canadian Distributor
Replacement Kit (see pg. 5-16)
For Dry-Capacitor & Ballast
(see pg. 5-6)
For Bracket & Capacitor
(see pg. 5-5, 5-7)
For Bracket & Dry-Capacitor
(see pg. 5-6, 5-7)
REFERENCE DRAWING PC2
000
200
500
A
B
0.843"
4.250˝
500K
0.250 Dia Thru
2 Holes
0.250 Dia Thru
2 Holes
2.937"
502K
3.875˝
4.375˝ 4.750˝
518
4.250˝
3.875˝
2.500"
4.375˝
5.375˝ 5.750˝
3.125"
3.125"
3.750"
700
WIRING DIAGRAMS
S
Wiring Diagram 19
Line
Cap
(Red)
Line
Wiring Diagram 21
Cap
(Red)
M
L
S
0.25”
0.25”
0.25”
See p. 5-7 for adjustable mounting brackets and detailed bracket drawings.
Com
(White)
or
PERMISSIBLE
Com
(Yellow)
Com (Yellow)
or (White)
Wiring Diagram 23
240V
208V
Cap
(Red)
120V
INC LAMP
W MAX
M
5.75”
6.10”
4.60”
277V
Com (Yellow)
or (White)
Com
(Yellow)
Com
(Yellow)
Wiring Diagram 24
347V
Line
277V
Lamp
(Blue)
Cap
(Red)
120V
Com
Com
(White)
Com
(White)
PAGE 5-45
FOR MORE INFORMATION CALL
1-800-BALLAST
(225-5278)
HID
CORE & COIL
718
Bracket
L
W
7.75” 1.25”
7.75” 2.75”
5.25” 1.25”
0.656"
.218" Dia Thru
4 Holes
A
B
MAX
120V (AUX)
BRef. Dwg.
PC2
PC3
4
REFERENCE DRAWING 4
0.250 Dia Thru
8 Holes
0.250 Dia Thru
4 Holes
A
B
MAX
Wiring Diagram 18
W
REFERENCE DRAWING PC3
HID CORE & COIL BALLASTS
MERCURY
Nom
Dimensions
Max Open
Input
Catalog*
Circuit Watts Input Circuit Fuse Wir Ref
Volts
Number
Type Input Current Voltage Rating Dia Dwg
A
(1) 400 WATT H33 MERCURY LAMP
R-NPF
4.60
10
240
430
240
24 4
1.7
1033-25S 11
2.60
5
R-HPF 3
R-NPF
4.25
10
430
277
24 4
1.7
277
1033-17S 11
2.40
5
R-HPF 3
480-120 H40048TAC4M
CWA 458 1.05
245
5
19 PC2 1.6
120
H400120AC4M
CWA 458 1.05
245
5
18 PC2 1.6
120 or
3.90
10
CWA 440 2.22
260
5
23 PC2 1.8
277 or H400TRIAC4M
347
1.92
5
120 or
3.90
10
208 or
2.22
8
CWA 440
245
21 PC2
1.6
H400MLTAC4M
240 or
1.92
5
277
1.68
5
(1) 1000 WATT H36 MERCURY LAMP
480-120 H100048TAC5M
CWA 1080 2.28
440
10 19 PC3 2.9
120 or
9.30
20
5.30
15
208 or
21 PC3 2.9
430
H1000MLTAC5M CWA 1080
240 or
4.50
10
277
4.00
10
3
10
MERCURY
400-1000
• 60 Hz
• Minimum starting
temperature: -30° C
• CWA, Normal and High Power
Factor models available
WATT
Capacitor
Ignitor
Oil Filled
Oval
Ht
Total
Weight
(lbs.)
Max
UL
Catalog Distance Bench
Number to lamp (ft) Top Rise
B
Min
Mfd Volt
Dry Film
Dia
Ht
3.2
22.5 240
1.5
3.6
1.56x2.69
3.5
6.1
n/a
n/a
B
3.2
22.5 277
1.5
3.6
1.56x2.69
3.5
6.1
n/a
n/a
C
3.4
3.4
35 240
35 240
1.6
1.8
3.6
3.6
1.91x2.91
1.91x2.91
3.1
3.1
9.5
9.5
n/a
n/a
n/a
n/a
C
C
3.5
35 240
1.8
3.6
1.91x2.91
3.1
9.5
n/a
n/a
A
3.4
35
240
1.6
3.6
1.91x2.91
3.1
9.5
n/a
n/a
C
4.7
24 480
1.8
3.6
1.91x2.91
3.9
19.5
n/a
n/a
4.7
24 480
n/a
n/a
1.91x2.91
3.9
19.5
n/a
n/a
C
B
A
B
B
Capacitors are available as an option for high power
factor operation.
Also can be used to operate (1) 215 watt S65 High Pressure Sodium lamp.
Electrical characteristics will vary from those shown.
DESCRIPTION
SUFFIX *
For Ballast Only
For Bracket Only (see pg. 5-7)
For Capacitor Only (see pg. 5-5, 5-6)
For Distributor Replacement Kit
(see pg. 5-13 thru 5-15)
For Canadian Distributor
Replacement Kit (see pg. 5-16)
For Dry-Capacitor & Ballast
(see pg. 5-6)
For Bracket & Capacitor
(see pg. 5-5, 5-7)
For Bracket & Dry-Capacitor
(see pg. 5-6, 5-7)
REFERENCE DRAWING PC2
000
200
500
A
B
0.843"
4.250˝
500K
0.250 Dia Thru
2 Holes
0.250 Dia Thru
2 Holes
2.937"
502K
3.875˝
4.375˝ 4.750˝
518
4.250˝
3.875˝
2.500"
4.375˝
5.375˝ 5.750˝
3.125"
3.125"
3.750"
700
WIRING DIAGRAMS
S
Wiring Diagram 19
Line
Cap
(Red)
Line
Wiring Diagram 21
Cap
(Red)
M
L
S
0.25”
0.25”
0.25”
See p. 5-7 for adjustable mounting brackets and detailed bracket drawings.
Com
(White)
or
PERMISSIBLE
Com
(Yellow)
Com (Yellow)
or (White)
Wiring Diagram 23
240V
208V
Cap
(Red)
120V
INC LAMP
W MAX
M
5.75”
6.10”
4.60”
277V
Com (Yellow)
or (White)
Com
(Yellow)
Com
(Yellow)
Wiring Diagram 24
347V
Line
277V
Lamp
(Blue)
Cap
(Red)
120V
Com
Com
(White)
Com
(White)
PAGE 5-45
FOR MORE INFORMATION CALL
1-800-BALLAST
(225-5278)
HID
CORE & COIL
718
Bracket
L
W
7.75” 1.25”
7.75” 2.75”
5.25” 1.25”
0.656"
.218" Dia Thru
4 Holes
A
B
MAX
120V (AUX)
BRef. Dwg.
PC2
PC3
4
REFERENCE DRAWING 4
0.250 Dia Thru
8 Holes
0.250 Dia Thru
4 Holes
A
B
MAX
Wiring Diagram 18
W
REFERENCE DRAWING PC3
547-RS-WS-TC-P
Application and Performance Specifications
Description: Electromagnetic ballast for (1) fluorescent lamp as indicated below:
• Line Voltage: 120 vac, + 5%, - 10%, 60Hz
• Rapid Start
• Low Power Factor
Typical Performance Data
Lamp
Input Current
Input Power
Power
Ballast
Ballast Efficacy
T.H.D.
Crest
Type
#
( Amps )
( Watts )
Factor
Factor
Factor
%
Factor
FC8T9
1
0.6
30
< .60
.85
2.83
< 10
< 1.7
FC6T9
1
0.64
27
< .60
.90
3.30
< 10
< 1.7
Application and Performance Specification Information Subject to Change without Notification.
Performance:
Safety:
• Designed in accordance with ANSI C82.1
• Compatible with PLC and IR systems
• Lag type circuit
• No PCB's
• UL listed (Class P, Indoor and Type 1 Outdoor, HL)
• CSA Certified
• Thermally Protected
Application:
Mechanical:
Overall
Mounting
• Minimum Starting Temperature: 50° F, 10° C
• Maximum Ballast Case Temperature not to exceed 90° C
• Sound Rated: A
• Remote Mounting: 20 feet with minimum 18 AWG
• Length:
• Width:
• Height:
6 7/16"
1 7/8"
1 1/2"
6"
• Lead Length ( inches, ± 1 ):
( refer to TechNote # 7b for other wire sizes/lengths )
Black
White (2)
Red (2), Blue (2)
• Weight:
10
10
9
2 lbs.
Footnotes:
* Available in white cans.
Warranty:
Universal Lighting Technologies warrants to the purchaser that each electronic ballast will be free from
defects in material or workmanship for a period of 24 months from date of manufacture when properly
installed and under normal conditions of use. Call 1-800-BALLASTx800 for technical assistance.
Manufactured in North America
Bla ck
Line
White
BALLA ST
R ed
R ed
Blue
White
Me tal conta cts
lam p to fixtu re
Ballast must be groun ded. Install in acco rdance with N atio nal Electric Cod e.
1-800-BALLAST
www.universalballast.com
December 1997
565-L-TC-P
Application and Performance Specifications
Description: Electromagnetic ballast for (1) fluorescent lamp as indicated below:
• Line Voltage: 120 vac, + 5%, - 10%, 60Hz
• Trigger Start
• High Power Factor (except as noted)
Typical Performance Data
Lamp
Input Current
Input Power
Power
Ballast
Ballast Efficacy
T.H.D.
Crest
Type
#
( Amps )
( Watts )
Factor
Factor
Factor
%
Factor
F20T12
1
0.28
30
> .90
.82
2.73
< 32
< 1.7
F15T8
1
0.28
27
> .60
0.87
3.19
< 32
< 1.7
F15T12
1
0.26
29
> .90
0.91
3.18
< 32
< 1.7
F14T12
1
0.25
27
> .90
0.75
2.76
< 32
< 1.7
Application and Performance Specification Information Subject to Change without Notification.
Performance:
Safety:
• Designed in accordance with ANSI C82.1
• Compatible with PLC and IR systems
• Lead type circuit
• No PCB's
• UL listed (Class P, Indoor and Type 1 Outdoor, HL)
• CSA Certified
• Thermally Protected
Application:
Mechanical:
• Minimum Starting Temperature: 50° F, 10° C
• Maximum Ballast Case Temperature not to exceed 90° C
• Sound Rated: A
• Remote Mounting: 20 feet with minimum 18 AWG
• Length:
• Width:
• Height:
Overall
Mounting
9 1/2"
2 3/8"
1 1/2"
8 57/64"
1 11/16"
• Lead Length ( inches, ± 1 ):
( refer to TechNote # 7b for other wire sizes/lengths )
White, Black
Red (2), Blue (2)
• Weight:
10
10
3.1 lbs.
Warranty:
Universal Lighting Technologies warrants to the purchaser that each electronic ballast will be free from
defects in material or workmanship for a period of 24 months from date of manufacture when properly
installed and under normal conditions of use. Call 1-800-BALLASTx800 for technical assistance.
Manufactured in North America
Line
Black
White
Blue
Red
BALLAST
Red
Blue
LAMP
Ballast must be grounded. Install in accordance with National Electric Code.
1-800-BALLAST
www.universalballast.com
December 1997
412-L-TC-P
Application and Performance Specifications
Description: Electromagnetic ballast for (1) fluorescent lamp as indicated below:
• Line Voltage: 120 vac, + 5%, - 10%, 60Hz
• Rapid Start
• High Power Factor (except as noted)
Lamp
Type
#
Input Current
( Amps )
F40T12*
F40T12ES
F40T10
1
1
1
0.48
0.44
0.49
Typical Performance Data
Input Power
Power
Ballast
( Watts )
Factor
Factor
57
51
57
> .98
> .90
> .90
Ballast Efficacy
Factor
T.H.D.
%
Crest
Factor
1.67
1.76
1.68
< 20
< 20
< 20
< 1.7
< 1.7
< 1.7
.95
.90
.95
Application and Performance Specification Information Subject to Change without Notification.
Performance:
Safety:
• Complies with ANSI standard C82.1
• Compatible with PLC and IR systems
• Lead type circuit
• No PCB's
• UL listed (Class P, Indoor and Type 1 Outdoor, HL)
• CSA Certified
• Thermally Protected
Application:
Mechanical:
• Minimum Starting Temperature: 60° F, 15° C for
• Length:
• Width:
• Height:
Energy Savings (34w) lamps; 50° F, 10° C for other lamps
• Maximum Ballast Case Temperature not to exceed 90° C
• Sound Rated: A
• Remote Mounting: 20 feet with minimum 18 AWG
( refer to TechNote # 7b for other wire sizes/lengths )
• For Export Only
Overall Mounting
9 1/2"
2 3/8"
1 1/2"
8 57/64"
1 11/16"
• Lead Length ( inches, ± 1 ):
Black/White
White
Red (2)
Blue/White (2)
• Weight:
25
25
37
27
3.1 lbs.
Footnotes:
* Not for use with "U" lamps.
Warranty:
Universal Lighting Technologies warrants to the purchaser that each electronic ballast will be free from
defects in material or workmanship for a period of 24 months from date of manufacture when properly
installed and under normal conditions of use. Call 1-800-BALLASTx800 for technical assistance.
Manufactured in North America
Black/ White
Line
Blue/ Whit e
White
Red
Red
BALLAST
Blue/ Whit e
LAMP
Ballast must be grounded. Install in accordance with National Electric Code.
1-800-BALLAST
www.universalballast.com
September 2004
544-L-TC
Application and Performance Specifications
Description:
• Line Voltage: 220 vac, + 5%, - 10%, 50Hz
• High Power Factor (except as noted)
• Rapid Start
Typical Performance Data
Lamp
Input Current
Input Power
Power
Ballast
Ballast Efficacy
T.H.D.
Crest
Type
#
( Amps )
( Watts )
Factor
Factor
Factor
%
Factor
F40T12
1
0.21
45
< .90
.76
1.71
< 32
< 2.0
F40T12ES
1
0.18
36
> .90
.70
1.95
< 32
< 2.0
F40T10
1
0.22
44
> .90
.72
1.66
< 32
< 2.0
F30T12ES
1
0.17
32
> .60
.70
2.22
> 32
< 2.0
F30T12
1
0.18
36
> .90
.71
1.97
< 20
< 2.0
Overall
Mounting
9 1/2"
2 3/8"
1 1/2"
8 57/64"
1 11/16"
Application and Performance Specification Information Subject to Change without Notification.
Performance:
Safety:
• Designed in accordance with ANSI C82.1
• Compatible with PLC and IR systems
• Lag type circuit
• No PCB's
• Thermally Protected
Application:
Mechanical:
• Minimum Starting Temperature: 60° F, 15° C for
• Length:
• Width:
• Height:
Energy Savings (34w) lamps; 50° F, 10° C for other lamps
• Maximum Ballast Case Temperature not to exceed 90° C
• Sound Rated: A
• Remote Mounting: 20 feet with minimum 18 AWG
• Lead Length ( inches, ± 1 ):
Black
( refer to TechNote # 7b for other wire sizes/lengths )
White, Blue
Red (2)
• Weight:
20
35
26
3.2 lbs.
Warranty:
Universal Lighting Technologies warrants to the purchaser that each electronic ballast will be free from
defects in material or workmanship for a period of 24 months from date of manufacture when properly
installed and under normal conditions of use. Call 1-800-BALLASTx800 for technical assistance.
Manufactured in North America
Black
Red
White
BALLAST
Red
Blue
LAMP
Line
Ballast must be grounded. Install in accordance with National Electric Code.
1-800-BALLAST
www.universalballast.com
December 1997
458-L-SLH-TC-P
Application and Performance Specifications
Description: Electromagnetic ballast for (1) fluorescent lamp as indicated below:
• Line Voltage: 277 vac, + 5%, - 10%, 60Hz
• Rapid Start
• High Power Factor
Lamp
Input Current
Input Power
Typical Performance Data
Power
Ballast
Ballast Efficacy
T.H.D.
Crest
Type
#
( Amps )
( Watts )
Factor
Factor
Factor
%
Factor
F40T12ES*
1
0.17
44
> .90
.88
2.00
< 20
< 1.85
F40T12
1
0.19
51
> .90
.95
1.86
< 20
< 1.7
F40T10
1
0.19
51
> .90
.90
1.76
< 20
< 1.7
Application and Performance Specification Information Subject to Change without Notification.
Performance:
Safety:
• Complies with ANSI standard C82.1
• Compatible with PLC and IR systems
• Meets U.S. Public Law 100-357 for energy efficiency
• Meets CSA Standard 654 for energy efficiency
• Lead type circuit
• No PCB's
• UL listed (Class P, Indoor and Type 1 Outdoor, HL)
• CSA Certified
• Thermally Protected
Application:
Mechanical:
• Minimum Starting Temperature: 60° F, 15° C for
• Length:
• Width:
• Height:
Energy Savings (34w) lamps; 50° F, 10° C for other lamps
• Maximum Ballast Case Temperature not to exceed 90° C
• Sound Rated: A
• Remote Mounting: 20 feet with minimum 18 AWG
Overall
Mounting
9 1/2"
2 3/8"
1 1/2"
8 57/64"
1 11/16"
• Lead Length ( inches, ± 1 ):
Black/White
( refer to TechNote # 7b for other wire sizes/lengths )
White
Red (2)
Blue/White (2)
• Weight:
25
25
37
27
3.5 lbs.
Footnotes:
* Not for use with "U" lamps.
* This ballast meets low-leakage current to ground requirements.
Warranty:
Universal Lighting Technologies warrants to the purchaser that each electronic ballast will be free from
defects in material or workmanship for a period of 36 months from date of manufacture when properly
installed and under normal conditions of use. Call 1-800-BALLASTx800 for technical assistance.
Manufactured in North America
Black
Line
White
Red
Red
Blue/White
BALLAST
Blue/White
LAMP
Ballast must be grounded. Install in accordance with National Electric Code.
1-800-BALLAST
www.universalballast.com
September 2004
502-A-TC-P
Application and Performance Specifications
Description: Electromagnetic ballast for (2) fluorescent lamps as indicated below:
• Line Voltage: 120 vac, + 5%, - 10%, 60Hz
• Rapid Start
• Parallel Lamp Operation
Lamp
• High Power Factor (except as noted)
Typical Performance Data
Power
Ballast
Input Current
Input Power
Ballast Efficacy
T.H.D.
Crest
Type
#
( Amps )
( Watts )
Factor
Factor
Factor
%
Factor
F40T12@100%
2
0.85
94
> .90
.88
0.94
< 20
< 1.7
F40T12 @ 20%
2
0.68
35
< .60
.20
0.57
< 32
< 1.7
F30T12 @ 20%
2
0.58
27
< .60
.21
0.77
< 32
< 1.9
F30T12@100%
2
0.87
83
> .60
.89
1.07
< 20
< 1.7
Application and Performance Specification Information Subject to Change without Notification.
Performance:
Safety:
• Designed in accordance with ANSI C82.1
• Lag-Lag type circuit
• No PCB's
• UL listed (Class P, Indoor and Type 1 Outdoor, HL)
• CSA Certified
• Thermally Protected
Application:
Mechanical:
Overall
Mounting
• Minimum Starting Temperature: 50° F, 10° C
• Maximum Ballast Case Temperature not to exceed 90° C
• Sound Rated: A
• Remote Mounting: 20 feet with minimum 18 AWG
( refer to TechNote # 7b for other wire sizes/lengths )
• Dimmable to 20% light output
• Length:
• Width:
• Height:
• Lead Length ( inches, ± 1 ):
Black
White
Red (2)
Blue/ White, Blu
Yellow (2)
Brown
• Weight:
16 3/8"
2 3/8"
1 1/2"
15 25/32"
1 11/16"
Footnotes:
* Requires two circuit-interrupting lampholders.
** Do not mix 30 & 40 Watt lamps on the same
control circuit.Control circuit attached to the brown
wire must be sized appropriately.
*** See complete warning in catalog.
20
38
26
38
26
20
6.5 lbs.
Warranty:
Universal Lighting Technologies warrants to the purchaser that each electronic ballast will be free from
defects in material or workmanship for a period of 24 months from date of manufacture when properly
installed and under normal conditions of use. Call 1-800-BALLASTx800 for technical assistance.
Manufactured in North America
DIMMER
Brown
Bla ck
W hite
Blue /W hite
BALLAST
Blue
Ye llo w
Ye llo w
Red
Red
LAMP No. 2
LAMP No. 1
L ine
Use d isconn ect
lamph old er on ly
Ballast must be grounded. Install in accordance with National Electric Code.
1-800-BALLAST
www.universalballast.com
October 1998
447-LR-TC-P
Application and Performance Specifications
Description: Electromagnetic ballast for (2) fluorescent lamps as indicated below:
• Line Voltage: 120 vac, + 5%, - 10%, 60Hz
• Trigger Start
• Series Lamp Operation
• Low Power Factor
Typical Performance Data
Lamp
Input Current
Input Power
Power
Ballast
Ballast Efficacy
T.H.D.
Crest
Type
#
( Amps )
( Watts )
Factor
Factor
Factor
%
Factor
F20T12
2
0.43
37
> .60
.56
1.51
< 20
< 1.7
F15T8
2
0.5
39
> .60
.75
1.92
< 20
< 1.7
F15T12
2
0.56
42
> .60
.80
1.90
< 20
< 1.7
Application and Performance Specification Information Subject to Change without Notification.
Performance:
Safety:
• Designed in accordance with ANSI C82.1
• Compatible with PLC and IR systems
• Lag type circuit
• No PCB's
• UL listed (Class P, Indoor and Type 1 Outdoor, HL)
• CSA Certified
• Thermally Protected
Application:
Mechanical:
Overall
Mounting
• Minimum Starting Temperature: 50° F, 10° C
• Maximum Ballast Case Temperature not to exceed 90° C
• Sound Rated: A
• Remote Mounting: 20 feet with minimum 18 AWG
• Length:
• Width:
• Height:
6 19/32"
2 3/8"
1 1/2"
6"
• Lead Length ( inches, ± 1 ):
( refer to TechNote # 7b for other wire sizes/lengths )
White, Black
Red (2), Blue (2)
Yellow (2)
• Weight:
10
13
18
2.5 lbs.
Warranty:
Universal Lighting Technologies warrants to the purchaser that each electronic ballast will be free from
defects in material or workmanship for a period of 24 months from date of manufacture when properly
installed and under normal conditions of use. Call 1-800-BALLASTx800 for technical assistance.
Manufactured in North America
Line
Black
White
Yellow
Red
Red
BALLAST
Yellow
Blue
B lue
LAMP
LAMP
Ballast must be grounded. Install in accordance with National Electric Code.
1-800-BALLAST
www.universalballast.com
December 1997
567-L-TC
Application and Performance Specifications
Description: Electromagnetic ballast for (2) fluorescent lamps as indicated below:
• Line Voltage: 220 vac, + 5%, - 10%, 60Hz
• Trigger Start
• Series Lamp Operation
• High Power Factor (except as noted)
Typical Performance Data
Lamp
Input Current
Input Power
Power
Ballast
Ballast Efficacy
T.H.D.
Crest
Type
#
( Amps )
( Watts )
Factor
Factor
Factor
%
Factor
F20T12
2
0.26
53
> .90
.83
1.55
< 20
< 1.7
F15T8
2
0.25
49
> .60
0.86
1.77
< 32
< 1.9
F15T12
2
0.24
47
> .90
0.85
1.81
< 20
< 1.9
F14T12
2
0.22
44
> .90
0.76
1.74
< 20
< 1.9
Overall
Mounting
9 1/2"
2 3/8"
1 1/2"
8 57/64"
1 11/16"
Application and Performance Specification Information Subject to Change without Notification.
Performance:
Safety:
• Designed in accordance with ANSI C82.1
• Compatible with PLC and IR systems
• Lead type circuit
• No PCB's
• Thermally Protected
Application:
Mechanical:
• Minimum Starting Temperature: 50° F, 10° C
• Maximum Ballast Case Temperature not to exceed 90° C
• Sound Rated: A
• Remote Mounting: 20 feet with minimum 18 AWG
• Length:
• Width:
• Height:
• Lead Length ( inches, ± 1 ):
( refer to TechNote # 7b for other wire sizes/lengths )
White, Black
Red (2), Blue (2)
Yellow (2)
• Weight:
10
13
16
3.3 lbs.
Warranty:
Universal Lighting Technologies warrants to the purchaser that each electronic ballast will be free from
defects in material or workmanship for a period of 24 months from date of manufacture when properly
installed and under normal conditions of use. Call 1-800-BALLASTx800 for technical assistance.
Manufactured in North America
Line
Black
White
Yellow
Red
Red
BALLAST
Yellow
Blue
Blue
LAMP
LAMP
Ballast must be grounded. Install in accordance with National Electric Code.
1-800-BALLAST
www.universalballast.com
December 1997
554-L-TC-P
Application and Performance Specifications
Description: Electromagnetic ballast for (2) fluorescent lamps as indicated below:
• Line Voltage: 277 vac, + 5%, - 10%, 60Hz
• Trigger Start
• Series Lamp Operation
• High Power Factor
Lamp
Typical Performance Data
Power
Ballast
Input Current
Input Power
Ballast Efficacy
T.H.D.
Crest
Type
#
( Amps )
( Watts )
Factor
Factor
Factor
%
Factor
F20T12
2
0.22
55
> .95
.86
1.55
< 20
< 1.7
F15T8
2
0.2
51
> .95
.89
1.76
< 20
< 1.9
F15T12
2
0.2
49
> .95
.87
1.78
< 20
< 1.9
F14T12
2
0.17
45
> .95
.79
1.76
< 20
< 1.9
Performance:
Safety:
• Designed in accordance with ANSI C82.1
• Compatible with PLC and IR systems
• Lead type circuit
• No PCB's
• UL listed (Class P, Indoor and Type 1 Outdoor, H
• CSA Certified
• Thermally Protected
Application:
Mechanical:
• Minimum Starting Temperature: 50° F, 10° C
• Maximum Ballast Case Temperature not to exceed 90° C
• Sound Rated: A
• Remote Mounting: 20 feet with minimum 18 AWG
• Length:
• Width:
• Height:
Overall
Mounting
9 1/2"
2 3/8"
1 1/2"
8 57/64"
1 11/16"
• Lead Length ( inches, ± 1 ):
( refer to TechNote # 7b for other wire sizes/lengths )
White, Black
Red (2), Blue (2)
Footnotes:
Yellow (2)
• Weight:
10
13
16
3.2 lbs.
Warranty:
Universal Lighting Technologies warrants to the purchaser that each electronic ballast will be free from
defects in material or workmanship for a period of 24 months from date of manufacture when properly
installed and under normal conditions of use. Call 1-800-BALLASTx800 for technical assistance.
Manufactured in North America
Line
Black
White
Yellow
BALLAST
Yellow
Blue
Blue
Red
Red
LAMP
LAMP
Ballast must be grounded. Install in accordance with National Electric Code.
1-800-BALLAST
www.universalballast.com
December 1997
446-LR-TC-P
Application and Performance Specifications
Description: Electromagnetic ballast for (2) fluorescent lamps as indicated below:
• Line Voltage: 120 vac, + 5%, - 10%, 60Hz
• Rapid Start
• Series Lamp Operation
• High Power Factor
Lamp
Type
F40T12
F40T12ES
F40T12/U
F40T10
#
Input Current
( Amps )
Input Power
( Watts )
2
2
2
2
0.77
0.66
0.77
0.78
91
75
91
93
Typical Performance Data
Power
Ballast
Factor
Factor
> .98
> .90
> .98
> .98
.93
.86
.91
.93
Ballast Efficacy
Factor
T.H.D.
%
Crest
Factor
1.02
1.15
1.00
1.00
< 20
< 20
< 20
< 20
< 1.7
< 1.9
< 1.7
< 1.7
Application and Performance Specification Information Subject to Change without Notification.
Performance:
Safety:
• Complies with ANSI standard C82.1
• Compatible with PLC and IR systems
• Lead type circuit
• No PCB's
• UL listed (Class P, Indoor and Type 1 Outdoor, HL)
• CSA Certified
• Thermally Protected
Application:
Mechanical:
• Minimum Starting Temperature: 60° F, 15° C for
• Length:
• Width:
• Height:
Energy Savings (34w) lamps; 50° F, 10° C for other lamps
• Maximum Ballast Case Temperature not to exceed 90° C
• Sound Rated: A
• Remote Mounting: 20 feet with minimum 18 AWG
Overall Mounting
9 1/2"
2 3/8"
1 1/2"
8 57/64"
1 11/16"
• Lead Length ( inches, ± 1 ):
White, Black
( refer to TechNote # 7b for other wire sizes/lengths )
Red (2), Blue (2)
• For Export Only
Yellow (2)
• Weight:
22
26
36
3.1 lbs.
Warranty:
Universal Lighting Technologies warrants to the purchaser that each electronic ballast will be free from
defects in material or workmanship for a period of 24 months from date of manufacture when properly
installed and under normal conditions of use. Call 1-800-BALLASTx800 for technical assistance.
Manufactured in North America
Line
Black
White
Yellow
Red
Red
BALLAST
Yellow
Blue
Blue
LAMP
LAMP
Ballast must be grounded. Install in accordance with National Electric Code.
1-800-BALLAST
www.universalballast.com
September 2004
754-L-TC-P
Application and Performance Specifications
Description: Electromagnetic ballast for (2) fluorescent lamps as indicated below:
• Line Voltage: 220 vac, + 5%, - 10%, 50Hz
• Rapid Start
• Series Lamp Operation
• High Power Factor
Lamp
Input Current
Input Power
Typical Performance Data
Power
Ballast
Ballast Efficacy
T.H.D.
Crest
Type
#
( Amps )
( Watts )
Factor
Factor
Factor
%
Factor
F40T12
2
0.43
93
> .98
.94
1.01
< 20
< 1.7
F40T12ES
2
0.37
77
> .90
0.87
1.13
< 32
< 1.9
F40T10
2
0.43
95
> .98
.93
0.98
< 20
< 1.7
Application and Performance Specification Information Subject to Change without Notification.
Performance:
Safety:
• Designed in accordance with ANSI C82.1
• Compatible with PLC and IR systems
• Lead type circuit
• No PCB's
• UL listed (Class P, Indoor and Type 1 Outdoor, HL)
• Thermally Protected
Application:
Mechanical:
• Minimum Starting Temperature: 60° F, 15° C for
• Length:
Energy Savings (34w) lamps; 50° F, 10° C for other lamps • Width:
• Height:
• Maximum Ballast Case Temperature not to exceed 90° C
• Lead Length ( inches, ± 1 ):
• Sound Rated: A
• Remote Mounting: 20 feet with minimum 18 AWG
White, Black
( refer to TechNote # 7b for other wire sizes/lengths )
Red (2), Blue (2)
Yellow (2)
• Weight:
Overall
Mounting
9 1/2"
2 3/8"
1 1/2"
8 57/64"
1 11/16"
22
26
36
3.5 lbs.
Warranty:
Universal Lighting Technologies warrants to the purchaser that each electronic ballast will be free from
defects in material or workmanship for a period of 24 months from date of manufacture when properly
installed and under normal conditions of use. Call 1-800-BALLASTx800 for technical assistance.
Manufactured in North America
Line
Black
White
Yellow
BALLAST
Yellow
Blue
Blue
Red
Red
LAMP
LAMP
Ballast must be grounded. Install in accordance with National Electric Code.
1-800-BALLAST
www.magnetek.com/ballast
December 1997
540-L-TC-P
Application and Performance Specifications
Description: Electromagnetic ballast for (2) fluorescent lamps as indicated below:
• Line Voltage: 220 vac, + 5%, - 10%, 60Hz
• Rapid Start
• Series Lamp Operation
• High Power Factor
Lamp
Input Current
Input Power
Typical Performance Data
Power
Ballast
Ballast Efficacy
T.H.D.
Crest
Type
#
( Amps )
( Watts )
Factor
Factor
Factor
%
Factor
F40T12
2
0.42
90
> .98
.91
1.01
< 20
< 1.7
F40T12ES
2
0.36
75
> .90
.86
1.15
< 20
< 1.9
F40T10
2
0.43
94
> .98
.93
0.99
< 20
< 1.7
Application and Performance Specification Information Subject to Change without Notification.
Performance:
Safety:
• Designed in accordance with ANSI C82.1
• Compatible with PLC and IR systems
• Lead type circuit
• No PCB's
• UL listed (Class P, Indoor and Type 1 Outdoor, HL)
• Thermally Protected
Application:
Mechanical:
• Minimum Starting Temperature: 60° F, 15° C for
• Length:
• Width:
• Height:
Energy Savings (34w) lamps; 50° F, 10° C for other lamps
• Maximum Ballast Case Temperature not to exceed 90° C
• Sound Rated: A
• Remote Mounting: 20 feet with minimum 18 AWG
Overall
Mounting
9 1/2"
2 3/8"
1 1/2"
8 57/64"
1 11/16"
• Lead Length ( inches, ± 1 ):
White, Black
( refer to TechNote # 7b for other wire sizes/lengths )
Red (2), Blue (2)
Yellow (2)
• Weight:
20
25
37
3.4 lbs.
Footnotes:
* For use on 22-volt systems with one grounded conductor
Warranty:
Universal Lighting Technologies warrants to the purchaser that each electronic ballast will be free from
defects in material or workmanship for a period of 24 months from date of manufacture when properly
installed and under normal conditions of use. Call 1-800-BALLASTx800 for technical assistance.
Manufactured in North America
Line
Black
White
Yellow
Red
Red
BAL LAST
Yellow
Blue
Blue
LAMP
LAMP
Ballast must be grounded. Install in accordance with National Electric Code.
1-800-BALLAST
www.universalballast.com
December 1997
443-L-TC-P
Application and Performance Specifications
Description: Electromagnetic ballast for (2) fluorescent lamps as indicated below:
• Line Voltage: 277 vac, + 5%, - 10%, 60Hz
• Rapid Start
• Series Lamp Operation
• High Power Factor
Lamp
Type
F40T12
F40T12ES
F40T12ES/U
F40T12/U
F40T10
#
Input Current
( Amps )
2
2
2
2
2
.36
.32
.32
.36
.37
Typical Performance Data
Input Power
Power
Ballast
( Watts )
Factor
Factor
96
82
82
98
101
> .90
> .90
> .90
> .98
> .98
Ballast Efficacy
Factor
T.H.D.
%
Crest
Factor
.97
1.08
1.08
.96
.93
< 20
< 20
< 20
< 20
< 20
< 1.7
< 1.9
< 1.9
< 1.7
< 1.7
.94
.88
.88
.94
.94
Application and Performance Specification Information Subject to Change without Notification.
Performance:
Safety:
• Complies with ANSI Standard C82.1
• Compatible with PLC and IR systems
• Lead type circuit
• No PCB's
• UL listed (Class P, Indoor and Type 1 Outdoor, HL)
• CSA Certified
• Thermally Protected
Application:
Mechanical:
• Minimum Starting Temperature: 60° F, 15° C for
• Length:
• Width:
• Height:
Energy Savings (34w) lamps; 50° F, 10° C for other lamps
• Maximum Ballast Case Temperature not to exceed 90° C
• Sound Rated: A
• Remote Mounting: 20 feet with minimum 18 AWG
Overall Mounting
9 1/2"
2 3/8"
1 1/2"
8 57/64"
1 11/16"
• Lead Length ( inches, ± 1 ):
White, Black
( refer to TechNote # 7b for other wire sizes/lengths )
Red (2), Blue (2)
• For Export Only
Yellow (2)
• Weight:
20
24
36
3.3 lbs.
Warranty:
Universal Lighting Technologies warrants to the purchaser that each electronic ballast will be free from
defects in material or workmanship for a period of 24 months from date of manufacture when properly
installed and under normal conditions of use. Call 1-800-BALLASTx800 for technical assistance.
Manufactured in North America
Line
B lack
W hite
Y ello w
Red
Red
BALLAST
Y ello w
Blue
Blue
LAMP
LAMP
Ballast must be grounded. Install in accordance with National Electric Code.
1-800-BALLAST
www.universalballast.com
September 2004
412-L-SLH-TC-P
Application and Performance Specifications
Description: Electromagnetic ballasts for (1) fluorescent lamp as indicated below:
• Line Voltage: 120 vac, + 5%, - 10%, 60Hz
• Rapid Start
• High Power Factor
Lamp
Type
F40T12ES*
F40T12
F40T10
#
Input Current
( Amps )
1
1
1
0.38
0.45
0.45
Typical Performance Data
Input Power
Power
Ballast
( Watts )
Factor
Factor
44
52
52
> .90
> .90
> .90
Ballast Efficacy
Factor
T.H.D.
%
Crest
Factor
2.00
1.83
1.73
< 20
< 20
< 20
< 1.9
< 1.7
< 1.7
.88
.95
.90
Application and Performance Specification Information Subject to Change without Notification.
Performance:
Safety:
• Complies with ANSI standard C82.1
• Compatible with PLC and IR systems
• Meets U.S. Public Law 100-357 for energy efficiency
• Meets CSA Standard 654 for energy efficiency
• Lead type circuit
• No PCB's
• UL listed (Class P, Indoor and Type 1 Outdoor, HL)
• CSA Certified
• Thermally Protected
Application:
Mechanical
• Minimum Starting Temperature: 60° F, 15° C for
• Length:
• Width:
• Height:
Energy Savings (34w) lamps; 50° F, 10° C for other lamps
• Maximum Ballast Case Temperature not to exceed 90° C
• Sound Rated: A
• Remote Mounting: 20 feet with minimum 18 AWG
Overall Mounting
9 1/2"
2 3/8"
1 1/2"
8 57/64"
1 11/16"
• Lead Length ( inches, ± 1 ):
Black/White
( refer to TechNote # 7b for other wire sizes/lengths )
White
Red (2)
Blue/White (2)
• Weight:
25
25
37
27
3.4 lbs.
Footnotes:
* Not for use with "U" lamps.
* This ballast meets low-leakage current to ground requirements.
Warranty:
Universal Lighting Technologies warrants to the purchaser that each electronic ballast will be free from
defects in material or workmanship for a period of 36 months from date of manufacture when properly
installed and under normal conditions of use. Call 1-800-BALLASTx800 for technical assistance.
Manufactured in North America
Black
Line
Blue
White
Red
BALLAST
Blue
Red
LAMP
Ballast must be grounded. Install in accordance with National Electric Code.
1-800-BALLAST
www.universalballast.com
September 2004
446-L-SLH-TC-P
Application and Performance Specifications
Description: Electromagnetic ballast for (2) fluorescent lamps as indicated below:
• Line Voltage: 120 vac, + 5%, - 10%, 60Hz
• Rapid Start
• Series Lamp Operation
• High Power Factor
Lamp
Input Current
Typical Performance Data
Input Power
Power
Ballast
Ballast Efficacy
T.H.D.
Crest
Type
#
( Amps )
( Watts )
Factor
Factor
Factor
%
Factor
F40T12ES
2
0.65
74
> .90
.90
1.22
< 20
< 1.9
F40T12ES/U
2
0.65
74
> .90
.90
1.22
< 20
< 1.9
F40T12/U
2
0.76
90
> .98
.93
1.03
< 20
< 1.7
F40T12
2
0.75
89
> .98
.94
1.06
< 20
< 1.7
F40T10
2
0.76
90
> .98
.95
1.06
< 20
< 1.7
Application and Performance Specification Information Subject to Change without Notification.
Performance:
Safety:
• Complies with ANSI standard C82.1
• Compatible with PLC and IR systems
• Meets U.S. Public Law 100-357 for energy efficiency
• Meets CSA Standard 654 for energy efficiency
• Lead type circuit
• No PCB's
• UL listed (Class P, Indoor and Type 1 Outdoor, HL)
• CSA Certified
• Thermally Protected
Application:
Mechanical:
• Minimum Starting Temperature: 60° F, 15° C for
• Length:
• Width:
• Height:
Energy Savings (34w) lamps; 50° F, 10° C for other lamps
• Maximum Ballast Case Temperature not to exceed 90° C
• Sound Rated: A
• Remote Mounting: 20 feet with minimum 18 AWG
Overall Mounting
9 1/2"
2 3/8"
1 1/2"
• Lead Length ( inches, ± 1 ):
Black
White
( refer to TechNote # 7b for other wire sizes/lengths )
Red (2), Blue (2)
Yellow (2)
• Weight:
8 57/64"
1 11/16"
22
22
26
36
3.4 lbs.
Footnotes:
* This ballast meets low-leakage current to ground requirements.
Warranty:
Universal Lighting Technologies warrants to the purchaser that each electronic ballast will be free from
defects in material or workmanship for a period of 36 months from date of manufacture when properly
installed and under normal conditions of use. Call 1-800-BALLASTx800 for technical assistance.
Manufactured in North America
Line
Black
White
Yellow
Red
Red
BALLAST
Yellow
Blue
Blue
LAMP
LAMP
Ballast must be grounded. Install in accordance with National Electric Code.
1-800-BALLAST
www.universalballast.com
September 2004
447-LR-VLH-TC-P
Application and Performance Specifications
Description: Electromagnetic ballast for (2) fluorescent lamps as indicated below:
• Line Voltage: 120 vac, + 5%, - 10%, 60Hz
• Trigger Start
• Series Lamp Operation
• Low Power Factor
Lamp
Input Current
Typical Performance Data
Input Power
Power
Ballast
Ballast Efficacy
T.H.D.
Crest
Type
#
( Amps )
( Watts )
Factor
Factor
Factor
%
Factor
F20T12
2
0.42
35
> .60
.55
1.57
< 20
< 1.7
F15T8
2
0.53
38
< .60
.76
2.02
< 20
< 1.7
F15T12
2
0.58
40
< .60
.77
1.93
< 10
< 1.7
F14T12
2
0.62
40
< .60
.77
1.95
< 20
< 1.7
Application and Performance Specification Information Subject to Change without Notification.
Performance:
Safety:
• Designed in accordance with ANSI C82.1
• Compatible with PLC and IR systems
• Lag type circuit
• No PCB's
• UL listed (Class P, Indoor and Type 1 Outdoor, H
• CSA Certified
• Thermally Protected
Application:
Mechanical:
Overall Mounting
• Minimum Starting Temperature: 50° F, 10° C
• Maximum Ballast Case Temperature not to exceed 90° C
• Sound Rated: A
• Remote Mounting: 20 feet with minimum 18 AWG
• Length:
• Width:
• Height:
6 19/32"
2 3/8"
1 1/2"
6"
• Lead Length ( inches, ± 1 ):
( refer to TechNote # 7b for other wire sizes/lengths )
White, Black
Red (2), Blue (2)
Yellow (2)
• Weight:
10
13
18
2.9 lbs.
Footnotes:
* This ballast meets low-leakage current to ground requirements.
Warranty:
Universal Lighting Technologies warrants to the purchaser that each electronic ballast will be free from
defects in material or workmanship for a period of 24 months from date of manufacture when properly
installed and under normal conditions of use. Call 1-800-BALLASTx800 for technical assistance.
Manufactured in North America
Line
Black
White
Yellow
Yellow
Red
Red
BALLAST
Blue
Blue
LAMP
LAMP
Ballast must be grounded. Install in accordance with National Electric Code.
1-800-BALLAST
www.universalballast.com
December 1997
546-B-TC-P
Application and Performance Specifications
Description: Electromagnetic ballast for (1) lamp as indicated below:
• Line Voltage: 120 vac, + 5%, - 10%, 60Hz
• Trigger Start
• Low Power Factor
Typical Performance Data
Lamp
Input Current
Input Power
Power
Ballast
Ballast Efficacy
T.H.D.
Crest
Type
#
( Amps )
( Watts )
Factor
Factor
Factor
%
Factor
F20T12
1
0.58
29
< .60
.82
2.83
< 10
< 1.7
F15T8
1
0.55
25
< .60
.89
3.50
< 10
< 1.7
F15T12
1
0.61
30
< .60
.96
3.23
< 10
< 1.7
F14T12
1
0.66
30
< .60
.86
2.87
< 10
< 1.7
Application and Performance Specification Information Subject to Change without Notification.
Performance:
Safety:
• Designed in accordance with ANSI C82.1
• Compatible with PLC and IR systems
• Lag type circuit
• No PCB's
• UL listed (Class P, Indoor and Type 1 Outdoor, HL)
• CSA Certified
• Thermally Protected
Application:
Mechanical:
Overall
Mounting
• Minimum Starting Temperature: 50° F, 10° C
• Maximum Ballast Case Temperature not to exceed 90° C
• Sound Rated: A
• Remote Mounting: 20 feet with minimum 18 AWG
• Length:
• Width:
• Height:
6 7/16"
1 7/8"
1 1/2"
6"
• Lead Length ( inches, ± 1 ):
( refer to TechNote # 7b for other wire sizes/lengths )
Black
White, Blue
Red (2)
• Weight:
10
17
12
1.9 lbs.
Footnotes:
* Requires one circuit-interrupting lampholder.
Warranty:
Universal Lighting Technologies warrants to the purchaser that each electronic ballast will be free from
defects in material or workmanship for a period of 24 months from date of manufacture when properly
installed and under normal conditions of use. Call 1-800-BALLASTx800 for technical assistance.
Manufactured in North America
Black
White
BALLAST
Blue
R ed
R ed
LAMP
U se disconne ct
Line
lam phold er o nly
Ballast must be grounded. Install in accordance with National Electric Code.
1-800-BALLAST
www.universalballast.com
December 1997