TVID212IR HD-TVI, Full HD 1080p Indoor IR Dome Camera Shown with snap-on cover. USER GUIDE: TVID212IR 855-388-7422 ♦ www.northernvideo.com 3625 Cincinnati Avenue, Rocklin, CA 95765 ♦ 888-874-3336 Rev. 062015 Table of Contents Precautions Features Dimensions Installation Assembly Connection OSD Menu Setup Trouble Shooting 02 | Dome Camera Safety information CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit. This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Regulatory Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.Operation of this equipment in a residential area is likely to cause interference, in which case the user will be required to correct the interference at his own expense. If the product is to be put out of operation definitively, take it to a local recycling plant for a disposal which is not harmful to the environment. Dome Camera | 03 Precautions Indoor only design, do not install outdoors. Choose an ideal location for the camera, location must be protected against moisture and vibration. Be careful not to scratch the camera unit, especially lens or dome cover. Use the camera within the temperature (14 ˚F ~ 122 ˚F) . Handle with care. Dropping it can cause serious damage. Do not aim camera into direct sunlight. Use an appropriate power supply, 12VDC or 24VAC. 04 | Dome Camera Features SONY 1/2.9" CMOS Sensor. Full HD-TVI(1920x1080) Resolution. Digital-WDR, 3D-DNR. Day & Night Function. Full OSD with Multi-language. Multi function : Sense up(x2~x8), Motion Detection, Privacy Mask, Mirror(H/V/R), D-Zoom. 25M range visible in total darkness with 24pcs of IR LEDs. 3-Axis Bracket for 3D(Pan/Tilt/Roll) rotation. Extra video connector for easy installation. Coaxial communication(Pelco-C) support. Dome Camera | 05 What's Included (1) CAMERA (1) WHITE HOUSING (1) VIDEO TEST CONNECTOR (1) MOUNTING HARDWARE PACKAGE (1) USER GUIDE Parts Identified IR TYPE (AI LENS) 06 | Dome Camera Dimensions 48.1 101 Ø100 Ø130.8 Ø109 Structure specification MECHANICAL Dimension Ø130.8 X 101(H)mm Weight Approx. 500g ENVIRONMENT Construction Plastic Ingress Protection Indoor Only Operating Temp 14°F~ 122°F Humidity 0% to 90% ELECTRICAL (Power Consumption) Power Supply Current Consumption Heater Regulated 12V DC ±10% 12V DC / 24V AC Dual voltage Max. 500mA (at 12V DC): LED ON Max. 130mA (at 12V DC) LED OFF Yes CERTIFICATION CE, FCC, ROHS Yes Dome Camera | 07 Installation HOW TO INSTALL 1. Opening the dome : Push in the latch button. (Remove the protection sheet after installing.) Protection sheet LATCH BUTTON 2. Removing the dome : Lift the dome. When you push the latch button, it is unlocked and you can lift the dome. To switch to white housing, gently push the bubble through the black housing. Make note of latch button & inner sleeve position. Switch to white housing by gently pushing bubble back in place with latch button & sleeve in same position. 08 | Dome Camera Installation 3. Camera installation (1) Fix the camera set with the supplied screws on ceiling or wall mount. If you don't use supplied screws, the camera may fall off. (2) Please refer to '4. Camera angle adjustment' regarding adjust camera angle. (3) Lens adjustment ① By turning the "Tele-Wide" knob, 1 you can access a range of focal 2 w lengths within specified limits. N T ② Then, by turning the "Near-Far" F knob, you can set the focus toward the desired object. ✽ For LED model, the IR LED bank is hinged, and can be moved back to allow access to lens adjustment. After lens adjustment is made, be sure to move IR LED bank back to original position. 4. Camera angle adjustment : (1) Pan adjustment : Grasp the disk of camera and then adjust direction to the right or left (-180˚~ 180˚) (2) Tilt adjustment : Grasp the LED cover of camera and then adjust direction up or down (6˚~ 90˚) (3) Roll adjustment : Grasp the camera holder and then rotate (-178˚~178˚) (4) Re-assemble the camera. LED COVER DISK R L U D ROTATION CAMERA HOLDER <Caution> Do not force past adjustment range or damage may occur. Hole M3x10 SCREW Fix the disk (Pan angle) using a screw driver on M3X10 screws in the holes Dome Camera | 09 Assembly SK -D3 00(IR) DOME COVER A SS ’Y Assembly SK -D3 00(IR) CAMERA MODULE AS S’Y LED COVER ASS ’Y SCREW CONTROL PC B AS S’ Y HAR NESS SCREW PUSH BUTTON DISK BASE CABLE < Ceiling mount> < Ceiling mount> Mounting SCERW TP1 3.5x20 2EA SCERW TP1 3.5x20 2EA < Ceiling mount > < Wall mount > <W a ll moun> t SCERW TP1 3.5x20 2EA SCREW TP1 3.5x20 2EA SCREW TP1 3.5x20 2EA <W a ll moun> t 10 | Dome Camera Take off the marked part by using nipper for lpacing cable out. Connection AC 24V / DC 12V VIDEO TERMINAL Dome Camera | 11 OSD Menu Set up • Main Set up EXPOSURE WHITE BALANCE BACKLIGHT DAY&NIGHT IMAGE SPECIAL RESET EXIT LENS / BRIGHTNESS / MODE / SHUTTER / AGC / SENS-UP AUTO / AUTO ext / MANUAL BLC / HLC / OFF AUTO_CDS / COLOR / BW DNR / SHARPNESS / COLOR GAIN / GAMMA / D-WDR / DEFOG / SHADING / MIRROR TITLE / PRIVACY / MOTION / D-ZOOM / LANGUAGE All the settings will be restored to the factory default Escape the menu • OSD Control Key 6 2 4 5 3 1 ①SET : . ②UP, ③DOWN : Used to move the cursor to up or down. ④LEFT, ⑤RIGHT : Used to move the cursor to left or right and change the value. ⑥EXT-VIDEO : installation. Plug-in your test monitor here. 12 | Dome Camera OSD Menu Set up OSD Menu Control and Set up The on-screen menu is operated with the control lever on the PCB. To call the on-screen menu, press the control lever straight downward. The main menu is displayed as follows. Select the menu item by tilting the control lever in direction ↑or ↓. Change an adjustment by tilting the control lever in direction ← or →. If “↵ ” is indicated beside menu item or an adjusting option, It is possible to call a submenu for further adjustments by pressing down on the control lever. To return from a submenu to the prior menu level, select the menu item RETURN and by pressing down the control lever. Via the submenu item RETURN, the menu is completely exited. Exit the main menu via the menu item EXIT. Dome Camera | 13 Menu Set up EXPOSURE Function of adjusting shutter speed and AGC LENS : Set to DC / DC auto-iris lens is standard. BRIGHTNESS : Adjust brightness level 0(dark) ~ 20(bright) MODE : Select AE MODE. INDOOR / OUTDOOR /DEBLUR SHUTTER : Can be set in AUTO or MANUAL AUTO : Auto shutter mode MANUAL : Adjust shutter manually. (1/30 ~ 1/60,000) AGC : Adjust AGC level 0(low) ~ 20(high) SENS-UP (X2~X8, OFF) : Select maximum DSS(Digital Slow Shutter) OFF, x2~X8 If only poor illumination is available, the light sensitivity of the camera can be increased. The shutter time is extended so that the exposure time covers several pictures. In the line SENSE UP it is possible to select if the sensitivity should be increased (ON) or not (OFF). If On has been selected, adjust the factor for the exposure time (X2 ~ X8) 14 | Dome Camera Menu Set up White Balance Function of adjusting WHITE BALANCE AUTO : Automatically adjusts color according to the lighting AUTOext : Faster extension version of Auto MANUAL : Manual white balance KELVIN : LOW / MIDDLE /HIGH R-GAIN : 0~20 B-GAIN : 0~20 Dome Camera | 15 Menu Set up BACKLIGHT Strong/large sources of light coming from behind the main subject (such as a person indoors that is in front of a window) cause the light meter to underexpose for the main subject. HLC : High Light Compensation / Masking the highlight in the image to distinguish the subject. BLC : Back Light Compensation / User controllable mode, shows the subject clearly. 16 | Dome Camera Menu Set up DAY & NIGHT Switching of day operation/ night operation AUTO : Automatic switching between day operation (color mode) and night operation (black and-white mode) depending on the ambient brigh tness - IR LED : IR LED ON/OFF setting - ANTI-SAT. : Compensate when IR hunting happens. When you use this function. - AGC THRS: Day&Night change level (AGC). Higher the value = Longer it takes for camera to switch from color to B/W. - AGC MARGIN : Day to night and night to day switch margin - DELAY : DAY&NIGHT change Delay time, 0 ~ 255 second - Cds LEVEL : Day&Night change level (CDS). DAY : Color mode always on NIGHT : Black-and-white mode always on Dome Camera | 17 Menu Set up IMAGE DNR(3D-DNR) : Select Digital Noise Reduction (OFF / LOW /MIDDLE / HIGH) SHARPNESS : Adjust sharpness level (0 ~ 10) COLOR GAIN : Adjust Color gain value (0 ~ 20) GAMMA : Selecte gamma mode. (0.45~0.65) D-WDR : Select Digital WDR(Wide Dynamic Range) (OFF / LOW /MIDDLE / HIGH) DEFOG : Adjust DEFOG mode. SHADING : Select Lens shading compensation. (OFF / ON) MIRROR : Activates Image mirror H-Flip : Flip the picture horizontally on the screen V-Flip : Flip the picture vertically on the screen Rotate : Flip the picture horizontally & vertically on the screen 18 | Dome Camera Menu Set up SPECIAL TITLE : Camera title edit and display on / off select. PRIVACY : Hide an area you want to hide on the screen.(16 point) MOTION : When there is movement of the subject on the screen, there will be motion detection. D-ZOOM : Select digital zoom magnification. Max 8x LANGUAGE : Select Language (English, Netherlandic, Italiano, Francais, Espanol, Deutsch) Dome Camera | 19 Menu Set up SYSTEM IMAGE RANGE : Select pedestal level scale FRAME RATE : Select HD output frame rate. 30 FPS / 25 FPS CVBS : Select CVBS output mode. NTSC or PAL 20 | Dome Camera Menu Set up RESET All the settings will be restored to the factory default EXIT Escape the menu Dome Camera | 21 Specification TVID212IR TVID212IR VIDEO Image Sensor Total Pixels Active Pixels Scanning System Resolution S/N Video Output Min.Illumination LENS TYPE Lens Type Focal Length OPERATIONAL On screen display Day & Night Brightness Shutter Speed Sens-up AGC Backlight HLC D-WDR White Balance Sharpness Digital Noise Reduction (3D) Digital Zoom Motion Detection Privacy Masking Mirror Defog 22 | Dome Camera 1/2.9" SONY CMOS 2010(H) 1108(V) = 2,227,080 (pixel) 1944(H) 1092(V) = 2,122,848 (pixel) Progressive Scan Digital : 1920X1080p (1080p, 30/25fps) 1280X720p (720p, 60/50fps) Analog : 700TVL More than 50dB (AGC OFF) HD-TVI Analog : NTSC, PAL Color: 1.0Lux, BW: 0.5Lux Color DSS: 0.002Lux, BW DSS : 0.001Lux DC Auto Iris f = 2.8(W) ~ 12.0(T)mm Yes TDN (Auto / Day / Night) 0 ~ 20 steps Auto / Manual (1/30(1/25) ~ 1/60000) OFF / ×2~ ×8 0~20 steps HLC / BLC / OFF ON / OFF ON / OFF Auto / Autoext / Manual 0~10 steps ON/OFF(X1~X8) ON / OFF ON / OFF (16 Zone Selectable) H / V / H&V / OFF ON / OFF Troubleshooting Nothing appears on screen. Check if the camera and monitor’s powers are on. (Also, the voltage and polarity.) Check if the video-out terminal of the camera and the video-in terminal of the monitor are correctly connected. Check if the iris of the lens is open. The screen seems blurry and darker. Adjust Contrast and Bright level in the menu. Check the setting of Image adjust in the menu. Check if there is any dust or scratches on the camera window The image focus is not correct. Adjust the camera lens either far or near to make focus. Motion detection function does not operate. Check if the MOTION DET setting is properly in the menu. Check the setting of motion detection area. The image does not seem to be shown correctly. Check if the video cable is connected correctly. Check if the video cable is used properly in certain distance. Overall, the picture’s color does not seem correct. Check if the setting of WHITE BALANCE is correct in the menu. Dome Camera | 23 Memo 24 | Dome Camera Memo Dome Camera | 25