Sabarmati River Front Development Corporation Limited
Electrical Work BOQ : 1 of 27
Section VII : Bills of Quantity
7.3 : Electrical work
Electrical Works
1
Section Feeder Panels
2
Point wiring & Distribution board
3
Cable Trenches, Manholes & Pipes
4
MV Cabling & Wires
5
Cable Connections
6
Street Light Poles & High Mast
7
Light Fixtures
8
Earthing
9
P.A. system
10
Miscellaneous
Total For Electrical Works
Signature and stamp of Bidder
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
1
DESCRIPTION
Section Feeder Panels
Supplying, unloading at site, shifting to site, assembling,
leveling, grouting, erecting, Testing, & Commissioning
double compartmentalized Street light control panel with
IP 65 protection & Enclauser should be powder coated
fabricated from 10 Guage M.S. sheet & folded channel
totally enclosed cubical type with made out of Modular
Panel Box System, Degree of Protection IP 65, in
accordance with IEC 60 529, type tested in accordance
with IEC 60 439 – 1. with pad lock arrangment. The
successful tenderer will have to prepare general
arrangement with dimensions & get it approve through
Architect/ Consultant. All civil work including RCC
platform for street light panel should be in scope of
Electrical contractor complete in all respect as per detail
drawing and directed by engineer incharge. with the 600
mm height MS angle covered stand. ( From Reputed
manufacture / CPRI Approved Panel Builder Only ) ( GA
Drawing will be approved by Design Consultant )
The panel board shall be made up of high quality
polycarbonate thermoplastic, shock proof, anti-corrosive,
acid & chemical resistant, fire retardant, self
extinguishing, highly impact resistant, halogen free, silicon
free, recyclable, having internally embedded gasket. The
switchboard (panel) shall have provision for future
expansion & shall be modular in construction. The bus
bars shall be connected with C type clamps without any
drilling on the bus bars. The panel shall be in accordance
with IEC 60 439 – 1 (Fully TTA). The Degree of Ingress
Protection shall be in accordance with IEC 60 529. & As
per specifications
Signature and stamp of Bidder
Electrical Work BOQ : 2 of 27
UNIT
QTY
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
1.1
Electrical Work BOQ : 3 of 27
DESCRIPTION
UNIT
QTY
SITC of the IP 65 Section feeder panel for the Street
Lighting Consisting of following
Incoming : 125 Amp FP SFU with the spreader link
R-Y-B-On-Off indicating Lamp with control fuse.
Busbar :
Set of 125 A. FP tinned copper busbars of EC. grade &
adequate capacity, size & insulated with color tape &
should be tined at all joints.
Auto/Manual bypass switch with indicating lamp
Meter : VAF meter equivalent to Enercon make ELF 3259
with 125/ 5 A Class 1 ct.
Outgoing : MCB's Should be of 10 KA.
Dual Channel Astronomical Timer Equivalent to Legrand
make Cat. No. 04767 with the battery back up : 4 nos.
no
10.0
no
100.0
40 amp. FP Power Contactor : 4 nos.
6 - 32 amp. DP Power Contactor : 6 nos.
40 Amp. FP MCB : 5 nos.
6 -32 Amp. FP MCB : 4 nos.
6 - 32 amp. SP MCB : 24 nos.
5 KVAR Capacitor with the 40 amp TP capacitor duty
contactor with the 10 minute time delay relay.
Panel Should Have lockable Space to incorporate the
2 nos of the 3 phase energy meter with its main
switches with separate cable entry & Watch Window.
1.3
SITC of IP66 Water Tight Junction Box 210mm x 260mm
x 117mm With necessary clamp for mounting of the J.B. (
All the cable / wire connections to the JB shall be with the
Water tight IP 66 Polyamide Glands, open Holes should
be sealed with the IP65 Grommets only ) J. B. Should be
provided with Hensel make cable connectors to connect 2
nos. of 25 sq. mm. x 4 core cables + Earthing wires. of
Hensel make cat. no. KD5355 + Connectors + IP65
Glands + IP65 Grommets
Signature and stamp of Bidder
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
Electrical Work BOQ : 4 of 27
DESCRIPTION
UNIT
1.4
SITC of IP66 Water Tight Junction Box 200mm x 160mm
x 98mm With necessary clamp for mounting of the J.B. (
All the cable / wire connections to the JB shall be with the
Water tight IP 66 Polyamide Glands, open Holes should
be sealed with the IP65 Grommets only ) J. B. Should be
provided with Hensel make cable connectors to connect 1
nos. of 10/16 sq. mm. x 4 core cables+ 4-5 nos. of 4 sq.
mm x 4 core wires + Earthing wires. of Hensel make cat.
no. KD5255 + Connectors + IP65 Glands + IP65
Grommets
no
200.0
1.5
SITC of IP66 Water Tight Junction Box 167mm x 125mm
x 82mm With necessary clamp for mounting of the J.B. (
All the cable / wire connections to the JB shall be with the
Water tight IP 66 Polyamide Glands, open Holes should
be sealed with the IP65 Grommets only ) J. B. Should be
provided with Hensel make cable connectors to connect 1
nos. of 6/10 sq. mm. x 4 core cables+ 4-5 nos. of 4 sq.
mm x 4 core wires + Earthing wires. of Hensel make cat.
no. KD5105 + Connectors + IP65 Glands + IP65
Grommets
no
50.0
1.6
SITC of IP66 Water Tight Junction Box 139mm x 115mm
x 70mm With necessary clamp for mounting of the J.B. (
All the cable / wire connections to the JB shall be with the
Water tight IP 66 Polyamide Glands, open Holes should
be sealed with the IP65 Grommets only ) J. B. Should be
provided with Hensel make cable connectors to connect 1
nos. of 6/10 sq. mm. x 4 core cables+ 4-5 nos. of 4 sq.
mm x 4 core wires + Earthing wires. of Hensel make cat.
no. KD5065 + Connectors + IP65 Glands + IP65
Grommets
no
50.0
Sub Total 1 .....
Signature and stamp of Bidder
QTY
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
2
DESCRIPTION
Electrical Work BOQ : 5 of 27
UNIT
QTY
Internal Wiring
Supply, installation, connection, testing & commissioning
of following outlet points as per Specification & IS. The
unit rate for the point shall consist of the circuit wiring from
LDB or switch board to outlet point through MCB / switch
as required & including the outlet points with connector &
sockets. A point shall include in addition to phase &
neutral wire, earth continuity wire from LDB to the final
termination at outlet points as per specification.
All the wiring, outlet points shall be done in a surface /
concealed manner with ISI approved medium duty, rigid
FR PVC, ISI conduit of minimum 25 mm. dia. using 650 V
FRLS copper conductor wire, modular switches with
suitable plate, PVC / Metal back box with brass chromium
/ cadmium plated machine screws etc.
2.1 Point Wiring
2.1.1 Wiring for the following light points with 1.5 sq.mm
FRLS flexible copper conductor 1100 volts grade
wires of approved make in concealed or surface
mounted 25 mm dia medium gauge PVC Conduit
including providing and fixing of 6 amps single pole
rocker operated flush mounted switch of approved quality
color make & design in 2 mm thick GI box and
earthing of fixtures and the outlet box with 1.5 sq.mm
PVC insulated copper conductor stranded flexible
"FRLS" wire.
a
b
c
Primary Light point controlled by one single way 6 A
switch.
Primary light point controlled by one SP MCB
Secondary light point controlled by same switch /
MCB
Signature and stamp of Bidder
no
75.0
no
no
20.0
125.0
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
DESCRIPTION
2.1.2 Wiring
for the Ceiling Fan points with 1.5
sq.mm FRLS flexible copper conductor 1100
volts
grade wires of approved make
in
concealed or surface mounted 25 mm dia medium
gauge PVC Conduit including providing fan hook
box, 6 amps switch and 300 watts electronic hum
free fan regulator of approved quality color make
& design in 2 mm thick GI box and earthing of
fixtures and the outlet box with 1.5 sq.mm PVC
insulated copper conductor stranded flexible
"FRLS" wire.
2.1.3 Wiring
for the 250 volts single phase and
neutral 6 amps switched socket outlet with 2.5
sq.mm FRLS flexible copper conductor 1100
volts
grade wires of approved make
in
concealed or surface mounted 25 mm dia medium
gauge PVC Conduit including providing and fixing
of 6 amps 5 pin switch socket outlet of approved
quality color make & design in 2 mm thick GI box
and earthing of fixtures and the outlet box with
1.5 sq.mm PVC insulated copper conductor
stranded flexible "FRLS" wire.
a
b
One 6 A x 5 pin 250 Volt socket outlet point controlled by
one 6 A switch located on board.
6 A x 5 pin 250 Volt switched socket outlet point at
convenient location.
Signature and stamp of Bidder
Electrical Work BOQ : 6 of 27
UNIT
QTY
no
50.0
no
50.0
no
75.0
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
Electrical Work BOQ : 7 of 27
DESCRIPTION
UNIT
2.1.4 Wiring
for the 250 volts single phase and
neutral 16 amps switched socket outlet with 2.5
sq.mm FRLS flexible copper conductor 1100
volts
grade wires of approved make
in
concealed or surface mounted 25 mm dia medium
gauge PVC Conduit including providing and fixing
of 16 amps 5 pin switch socket outlet of approved
quality color make & design in 2 mm thick GI box
and earthing of fixtures and the outlet box with
1.5 sq.mm PVC insulated copper conductor
stranded flexible "FRLS" wire.
no
25.0
2.1.5 DO - as 2.1.4 but with4 sq.mm wire for phase & Neutral &
2.5 sq. mm for Earthing
2.1.6 Wiring
for the Exhaust fan point with 1.5 sq.mm
FRLS flexible copper conductor 1100 volts grade
wires of approved make in concealed or surface
mounted 25 mm dia medium gauge PVC Conduit
including providing and fixing of 6 amps flush mounted
switch at the normal switch level in 2 mm thick GI box and
6 amps 3 pin flush mounted socket out of near exhaust
fan and earthing of exhaust fan through the third pin of the
socket outlet of approved quality color make & design in 2
mm thick GI box and earthing of fixtures and the
outlet box with 1.5 sq.mm PVC insulated copper
conductor stranded flexible "FRLS" wire.
no
25.0
no
20.0
2.1.7 Supply and laying of 25 mm rigid PVC pipe of 1.6-1.8 mm
thickness
2.2 Distribution Board-TPN
2.2.1 Supply, Erecting, testing and commissioning of only TPN
D.B. PPI type with space for FPMCB as incoming and
space for DPELMCB and 12 SPMCB as outgoing per
phase (i.e. 16 way per phase D.B.) of Hensel Make
KV9448M
mtr
2,500.0
no
2.0
Signature and stamp of Bidder
QTY
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
DESCRIPTION
Electrical Work BOQ : 8 of 27
UNIT
QTY
2.2.2 Supply, Erecting, testing and commissioning of only TPN
D.B. PPI type with space for FPMCB as incoming and
space for DPELMCB and 8 SPMCB as outgoing per
phase (i.e. 12 way per phase D.B.) of Hensel Make
KV9448M
no
1.0
2.2.3 Supply, Erecting, testing and commissioning of only TPN
D.B. PPI type with space for FPMCB as incoming and
space for DPELMCB and 4 SPMCB as outgoing per
phase (i.e. 8 way per phase D.B.) of Hensel Make
KV9336M
no
1.0
2.2.4 Supply, Erecting, testing and commissioning of only TPN
D.B. PPI type with space for FPMCB as incoming and
space for DPELMCB and 2 SPMCB as outgoing per
phase (i.e. 6 way per phase D.B.) of Hensel Make
KV9224M
no
1.0
no
4.0
2.3.2 Supply, Erecting, testing and commissioning of SPN D.B.
PPI type with space for DPELMCB as incoming and 8
SPMCB as outgoing per phase (i.e. 12 way D.B.) of
Hensel Make KV9112M
no
20.0
2.3.3 Supply, Erecting, testing and commissioning of SPN D.B.
PPI type with space for DPELMCB as incoming and 4
SPMCB as outgoing per phase (i.e. 8 way D.B.) of Hensel
Make KV7109M
no
3.0
2.3.4 Supply, Erecting, testing and commissioning of SPN D.B.
PPI type with space for DPELMCB as incoming and 2
SPMCB as outgoing per phase (i.e. 6 way D.B.) of
Hensel Make KV7106M
no
3.0
2.3.5
2.3.6
2.3.7
2.3.8
2.3.9
2.3.10
2.3.11
2.3.12
no
no
no
no
no
no
no
no
350.0
50.0
10.0
35.0
15.0
10.0
10.0
10.0
2.3 Distribution Board-SPN
2.3.1 Supply, Erecting, testing and commissioning of SPN D.B.
PPI type with space for DPELMCB as incoming and 12
SPMCB as outgoing per phase (i.e. 16 way D.B.) of
Hensel Make KV9118M
6-32 Amp. SP MCB
6-32 Amp. DP MCB
25 A / 100 mA DP ELMCB
32 A / 100 mA DP ELMCB
40 A / 100 mA DP ELMCB
6-32 Amp. FP MCB
40 Amp. FP MCB
20 Amp. DP din Rail Mounted Power Contactor
Signature and stamp of Bidder
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
DESCRIPTION
Electrical Work BOQ : 9 of 27
UNIT
QTY
2.3.13 40 Amp. FP din Rail Mounted Power Contactor
2.3.14 Supplying & erecting approved make Digital time switch
having minimum lithium cell 6 years operative and
operate battery backup 1 channel day clock with 14
memory programme, suitable to operate on 240V + 5%,
16A with, floating contacts Minimum switching setup time
1 minimum & LCD display. Also comprised permanent
ON/OFF switching. Programming switches & housed in
fire proof thermoplastic enclosure & transparent cover
erected as required with necessary connection. Dual
Channel Timer Equivalent to Legrand make Cat. No.
04767
no
no
10.0
10.0
2.3.15 10A x 250 Volt single phase Power socket outlet point
having IP rating of IP:65 at convenient location with
MCB.for outdoor duty.
2.3.16 20A x 250 Volt single phase Power socket outlet point
having IP rating of IP:65 at convenient location with
MCB.for outdoor duty.
2.3.17 32A x 415 Volt three phase Power socket outlet point
having IP rating of IP:65 at convenient location with
MCB.for outdoor duty.
no
5.0
no
5.0
no
5.0
mt
5,000.0
mt
1,000.0
3.0
3.1
3.2
Sub Total 2 .....
Cable Trenches, Manholes & Pipes
Making trench in soft soil of suitable width of 90 cms deep
from the final ground level or road level for laying cable or
locating the fault all over the run and backfilling the same
& clearing the site by removing debris & Shifting of the
debris & making site good As per the Instruction of the
Engineer In charge.
Covering of cable with second class bricks laid cover the
cable crosswise & also on both sides with covering of 7. 5
Cms. layer of sand above & below cable (cable shall be
laid in 0.9mtr.deep & 0.4 Mtr.wide trench). Where there
are more than one cable in the trench on either side of the
cable, 5 Cms. over lapping of bricks shall be provided.
Signature and stamp of Bidder
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
Electrical Work BOQ : 10 of 27
DESCRIPTION
UNIT
3.3
Drilling the road without breaking the road surface
(Asphalt) for laying of cable for feeding power supply by
making Suitable size of holes at both ends complete.
mt
3.4
Providing cement concrete.for foundation or for concrete Cu. Mtr.
filling in M20 Grade Cement Concrete duly plastered with
necessary curing for pole muffing or any other purpose.
Scope includes all necessary digging & Backfilling.
5.0
3.5
Construction of brick masonry pulling chamber 600 mm
x 600 mm inside clear size and depth up to 0.6 meter with
230 mm thick masonry in cement mortar proportion
1:5,cement finish cement plaster in CM proportion of 15
mm thickness from inside with 150 mm thick PCC at
bottom with top slab minimum 200 mm thickness in M20
grade with reinforcement. The rate shall be inclusive of
providing and fixing frame and 600 mm dia cover of FRC
for the Heavy Duty. Rate also inclusive of excavation and
back filling & clearing the site by removing debris &
Shifting of the debris & making site good As per the
Instruction of the Engineer In charge complete in all
respect.
no
5.0
3.6
Construction of brick masonry pulling chamber 750 mm
x 750 mm inside clear size and depth up to 1.25 meter
with 350 mm thick masonry in cement mortar proportion
1:5,cement finish cement plaster in CM proportion of 15
mm thickness from inside with 150 mm thick PCC at
bottom with top slab minimum 200 mm thickness in M20
grade with reinforcement. The rate shall be inclusive of
providing and fixing frame and 900 mm dia cover of FRC
for the Heavy Duty. Rate also inclusive of excavation and
back filling & clearing the site by removing debris &
Shifting of the debris & making site good As per the
Instruction of the Engineer In charge complete in all
respect.
no
5.0
Signature and stamp of Bidder
QTY
100.0
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
Electrical Work BOQ : 11 of 27
DESCRIPTION
UNIT
3.7
Construction of brick masonry pulling chamber 1000 mm
x 1000 mm inside clear size and depth up to 1.75 meter
with 350 mm thick masonry in cement mortar proportion
1:5,cement finish cement plaster in CM proportion of 15
mm thickness from inside with 150 mm thick PCC at
bottom with top slab minimum 200 mm thickness in M20
grade with reinforcement. The rate shall be inclusive of
providing and fixing frame and 900 mm dia cover of FRC
for the Heavy Duty. Rate also inclusive of excavation and
back filling & clearing the site by removing debris &
Shifting of the debris & making site good As per the
Instruction of the Engineer In charge complete in all
respect.
no
5.0
3.8
Construction of brick masonry pulling chamber 1250 mm
x 1250 mm inside clear size and depth up to 1.75 meter
with 350 mm thick masonry in cement mortar proportion
1:5,cement finish cement plaster in CM proportion of 15
mm thickness from inside with 150 mm thick PCC at
bottom with top slab minimum 200 mm thickness in M20
grade with reinforcement. The rate shall be inclusive of
providing and fixing frame and 1000 mm dia cover of
FRC for the Heavy Duty. Rate also inclusive of excavation
and back filling & clearing the site by removing debris &
Shifting of the debris & making site good As per the
Instruction of the Engineer In charge complete in all
respect.
no
5.0
3.9
Providing & laying. R.C.C. hume pipe N.P. 2 class for
cable to be laid 90 cms. below ground across the road
crossing or on floor with necessary material in an
approved manner
mt
mt
mt
50.0
50.0
50.0
(A) 250 mm dia
(B)150 mm dia
(C) 200 mm dia.
Signature and stamp of Bidder
QTY
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
DESCRIPTION
Electrical Work BOQ : 12 of 27
UNIT
QTY
3.10 Providing & laying Double walled corrugated pipes (DWC)
of polyethylene(conforming to IS 14930 II ) with necessary
connecting accessories of same material at 0.7 mtr.
depth for laying of cable. below ground / road surface for
enclosing cable and including digging the ground &
backfilling the same to make ground as per original.
(A)50 mm dia
(B)90 mm dia
(C)120 mm dia.
3.11 Supplying & Fixing of following sizes 2 mm thick and ISI
mark (embossed) RIGID PVC Conduit along with
accessories & Continuous fish wire in surface / Recess /
in Ground including cutting the wall and making good the
same in case of recess conduit if required. including
digging the ground & backfilling the same to make ground
as per original.
mt
mt
mt
10,000.0
3,000.0
2,000.0
(A) 20mm
(B) 25mm
(C) 32mm
(D) 40mm
Sub Total 3.....
Cables
Supply and Laying XLPE(IS:7098) )(I)-88 ISI marked
armored cable of Cu. / Aluminum conductor of 1.1
KV.grade of following sizes in ground or in pre-laid DWC
pipe / Trenches with necessary cable identification mark
to be provided at distance of 15 mt. & with 2 nos. of 16
SWG G.I. wire continuous in length per cable.
mt
mt
mt
mt
5,000.0
10,800.0
2,000.0
3,500.0
35 sq.mm x 3.5 c Al. cable
25 sq.mm x 4 c Al. cable
16 sq.mm x 4 c Al. cable
10 sq.mm x 4 c Al. cable
6 sq.mm x 4 c Al. cable
6 sq.mm x 4 c Cu. cable
4 sq.mm x 4 c Cu. cable
4 sq.mm x 3 c Cu. cable
mt
mt
mt
mt
mt
mt
mt
mt
50.0
500.0
3,500.0
3,500.0
3,000.0
750.0
750.0
1,000.0
4.0
4.1
4.1.1
4.1.2
4.1.3
4.1.4
4.1.5
4.1.6
4.1.7
4.1.8
Signature and stamp of Bidder
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
4.2
4.2.1
4.2.2
4.2.3
4.2.4
4.2.5
5.0
DESCRIPTION
Supplying and laying Flexible FR PVC insulated
multistrand multicore 1.1 kv grade ISI marked copper
wires of following size in HMS PVC Pipe.
1.00 Sq.mm 4 core round PVC sheathed
1.50 Sq.mm 3 core round PVC sheathed
2.50 Sq.mm 3 core round PVC sheathed
4.00 Sq.mm 3 core round PVC sheathed
6.00 Sq.mm 3 core round PVC sheathed
Sub Total 4.....
Cable Termination
Supplying & fixing of Thermoplastic glands (IP65) of
Spelsberg or Hensel make & making joint with necessary
crimping socket of long nack type connecting the same to
various equipment etc. for the following sizes:
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
35 sq.mm x 3.5 c Al. cable
25 sq.mm x 4 c Al. cable
16 sq.mm x 4 c Al. cable
10 sq.mm x 4 c Al. cable
6 sq.mm x 4 c Al. cable
6 sq.mm x 4 c Cu. cable
4 sq.mm x 4 c Cu. cable
4 sq.mm x 3 c Cu. cable
Sub Total 5.....
6.0 Street light Poles
6.1 Street Light Poles
6.1.1 Supply & installation of decorative Column of 4.1 mtr
height above the ground level primered & painted as per
the approved color & Shade - minimum 2 coats PU based
MRF Paint Factory Finish. The column shall also be
provided with flush door at the bottom with proper
strengthening to the cutout of the door opening. A
junction/ looping box with 32 Amps heavy duty connector
shall be built into the pole. street light pole with Single Arm
Bracket / arrangement for the top mounting fixture as per
drawing.
1) 8 way connector and 6A MCB
2) 50 mm diameter DWC pipe for each cable entry. Pipe
length is up to 3.5 mtr. Per cable
Signature and stamp of Bidder
Electrical Work BOQ : 13 of 27
UNIT
QTY
mt
mt
mt
mt
mt
1,000.0
5,000.0
5,000.0
4,000.0
2,000.0
no
no
no
no
no
no
no
no
10.0
50.0
400.0
400.0
250.0
100.0
100.0
100.0
no
225.0
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
DESCRIPTION
Electrical Work BOQ : 14 of 27
UNIT
QTY
3) Wiring up to the light fixture from the junction box
using 3core x 1.5 sq.mm. flexible copper wires per Fixture
of specified make.
4) 1 mtr. depth M20 grade Concrete coping with 0.6 mtr.
foundation bolt with base plate with stiffener as per
drawing.
5) Spiral/Coil Type Earthing from the 6 swg G.I. Wire of
2.5 mtr. With the suitable size pipe with clamps and
painting.
6) Radium strip of two color at suitable height
7) Excavation & back filling for erection of poles. Debris to
be removed from the site to suitable location as per the
instruction of the engineer in charge
6.1.2 Supply & installation of decorative Column of 5.1 mtr
height above the ground level primered & painted as per
the approved color & Shade - minimum 2 coats PU based
MRF Paint Factory Finish. The column shall also be
provided with flush door at the bottom with proper
strengthening to the cutout of the door opening. A
junction/ looping box with 32 Amps heavy duty connector
shall be built into the pole. street light pole with Single Arm
Bracket / arrangement for the top mounting fixture as per
drawing. ( Type 1 Pole )
1) 8 way connector and 6A MCB
2) 50 mm diameter DWC pipe for each cable entry. Pipe
length is up to 3.5 mtr. Per cable
3) Wiring up to the light fixture from the junction box
using 3core x 1.5 sq.mm. flexible copper wires per Fixture
of specified make.
4) 1 mtr. depth M20 grade Concrete coping with 0.6 mtr.
foundation bolt with base plate with stiffener as per
drawing.
5) Spiral/Coil Type Earthing from the 6 swg G.I. Wire of
2.5 mtr. With the suitable size pipe with clamps and
painting.
6) Radium strip of two color at suitable height
Signature and stamp of Bidder
no
25.0
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
DESCRIPTION
Electrical Work BOQ : 15 of 27
UNIT
QTY
7) Excavation & back filling for erection of poles. Debris to
be removed from the site to suitable location as per the
instruction of the engineer in charge
6.1.3 Supply & installation of decorative Column of 5.1 mtr
height above the ground level primered & painted as per
the approved color & Shade - minimum 2 coats PU based
MRF Paint Factory Finish. The column shall also be
provided with flush door at the bottom with proper
strengthening to the cutout of the door opening. A
junction/ looping box with 32 Amps heavy duty connector
shall be built into the pole. street light pole with Single Arm
Bracket / arrangement for the top mounting fixture as per
drawing. ( Type 2 Pole )
1) 8 way connector and 6A MCB
2) 50 mm diameter DWC pipe for each cable entry. Pipe
length is up to 3.5 mtr. Per cable
3) Wiring up to the light fixture from the junction box
using 3core x 1.5 sq.mm. flexible copper wires per Fixture
of specified make.
4) 1 mtr. depth M20 grade Concrete coping with 0.6 mtr.
foundation bolt with base plate with stiffener as per
drawing.
5) Spiral/Coil Type Earthing from the 6 swg G.I. Wire of
2.5 mtr. With the suitable size pipe with clamps and
painting.
6) Radium strip of two color at suitable height
7) Excavation & back filling for erection of poles. Debris to
be removed from the site to suitable location as per the
instruction of the engineer in charge
Signature and stamp of Bidder
no
25.0
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
DESCRIPTION
6.1.4 Supply & installation of decorative Column of 6.2 mtr
height above the ground level primered & painted as per
the approved color & Shade - minimum 2 coats PU based
MRF Paint Factory Finish. The column shall also be
provided with flush door at the bottom with proper
strengthening to the cutout of the door opening. A
junction/ looping box with 32 Amps heavy duty connector
shall be built into the pole. street light pole with Single Arm
Bracket / arrangement for the top mounting fixture as per
drawing.
1) 8 way connector and 6A MCB
2) 50 mm diameter DWC pipe for each cable entry. Pipe
length is up to 3.5 mtr. Per cable
3) Wiring up to the light fixture from the junction box
using 3nos x 1.5 sq.mm. flexible copper wires / Fixture of
specified make.
4) 1.2 mtr. depth M20 grade Concrete coping with 0.6 mtr.
foundation bolt with base plate with stiffener as per
drawing.
5) Spiral/Coil Type Earthing from the 6 swg G.I. Wire of
2.5 mtr. With the suitable size pipe with clamps and
painting.
6) Radium strip of two color at suitable height
7) Excavation & back filling for erection of poles. Debris to
be removed from the site to suitable location as per the
instruction of the engineer in charge
Signature and stamp of Bidder
Electrical Work BOQ : 16 of 27
UNIT
no
QTY
25.0
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
DESCRIPTION
6.1.5 Supply & installation of GRP pole with Two Nos.
Electrical Work BOQ : 17 of 27
UNIT
QTY
no
5.0
no
5.0
single arm bracket to be fixed at various height for
street light having top 76.0mm O.D. & bottom 277.0
mm O.D. with avg. thickness of 10.0 mm 10 Mtr
long ( effective length should be 10 Mtr.above GF)
with
1) Water tight Junction box of Hensel make with 8
way connector and 2 nos of 2A MCB
2) 50 mm diameter DWC pipe for each cable entry.
Pipe length is up to 3.5 mtr. Per cable.
3) Wiring up to the light fixture from the junction box
using 3c x 1.5 sq.mm. flexible copper wires / fixture
of specified make.
4) 2 mtr. Depth & 600 mm x 600 mm Concrete
coping Concrete coping with base plate with sleeve
for pole with stiffener as per drawing.
5) Spiral/Coil Type Earthing
6) Excavation for erection of poles.
6.1.6 Supply & installation of 11Mtr (Approx 36') high (coloured
and primered in minimum 2 coats of PU based paint in
approved colour and shade) made out of M.S. tubular
pole of dia 194 mm top swaged with base plate with
stiffner, primered and painted street light pole The column
shall also be provided with flush door at the bottom with
proper strengthening to the cutout of the door opening. A
junction/ looping box with Heavy duty 3 phase connector
shall be built into the pole with single arm bracket from the
42 to 60 mm dia pipe with Suitable size of M.S. sleeve
/reducer duly welded at the end of the arm, The total play
should not be more than 10 mm as per drawing.
1) 8 way connector and 6A MCB
2) 50 mm diameter DWC pipe for each cable entry. Pipe
length is up to 3.5 mtr. Per cable
3) Wiring up to the light fixture from the junction box
using 3nos x 1.5 sq.mm. flexible copper wires / Fixture of
specified make.
4) Concrete coping with base plate with stiffner.
Signature and stamp of Bidder
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
DESCRIPTION
Electrical Work BOQ : 18 of 27
UNIT
QTY
5) Sprial/Coil Type Earthing from the 8 swg Cu. Wire of
2.5 mtr. With the suitable size pipe with clamps and
painting.
6) Radium stip of two colour at suitable height
7) Excavation & back filling for erection of poles. Debris to
be removed from the site to suitable location as per the
instruction of the engineer incharge
6.1.7 SITC of Decorative pole with fixture of Schreder make
decorative Sextant Pole 12 m made out of G.I., primered
and painted PU factory finish. T. A junction/ looping box
with Heavy duty 3 phase connector shall be suitable into
the pole along with Sexant Bracket suitable for 3
Luminaire in GI with following
1) 8 way connector and 6A MCB
2) 50 mm diameter DWC pipe for each cable entry. Pipe
length is up to 3.5 mtr. Per cable
3) Wiring up to the light fixture from the junction box
using 3nos x 1.5 sq.mm. flexible copper wires / Fixture of
specified make.
4) M 20 grade Concrete coping with base plate with
stiffner.
5) Sprial/Coil Type Earthing from the 8 swg Cu. Wire of
2.5 mtr. With the suitable size pipe with clamps and
painting.
6) Radium stip of two colour at suitable height
7) Excavation & back filling for erection of poles. Debris to
be removed from the site to suitable location as per the
instruction of the engineer incharge
Sub Total 6.....
Signature and stamp of Bidder
27.0
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
7.0
DESCRIPTION
Electrical Work BOQ : 19 of 27
UNIT
QTY
Light Fixtures
Supply, Installation, Testing & Commissioning of the
following Light Fixture with lamp, Control Gear & All
necessary accessories.
Luminaries with all electrical accessories & it should be
energy efficient, low loss, ortho cyclically wound open
construction copper ballast, ignitor & power factor
improvement capacitor or Electronics Ballast etc are
prewired up to the terminal block & mounted on a
removable control gear module for ease of maintenance.
All electrical connections of the control gear module with
the rest of the luminaries should be click fix & foolproof &
require use of no tools. Mounting options should be for
both lateral as well as pole top mounting. with Lamp
Control Gear & Fixing Accessories.
All the light fixtures will be finally approved by Architect /
Consultant. Architect / Consultant reserves the right to
reject the fittings suggested by the contractor.
7.1
1 x 28 watt T5 Light fixture with Lamp of Philips make
TWG 207 1 x TL5 - 28 watt HF
1 X 11 watt mirolta type Light Fixture of Philips make FMS
200/ 111
1 x 150 watt IP42 Suspended Light fixtures with all
necessary hanging arrangement of Philips make Cat. No.
MPK 632 C 1 x 150 w CDM-T GR with Glass
no
50.0
no
20.0
no
15.0
7.4
IP67 Drive over Ground Burial Light fixture with 70 watt
CDM-T with Integral Control Gear with Body made of die
cast alluminium with 1 / 2 / 12 windows protective guards
of 8mm thikness with tempered prismed glass diffuser
and stainless steel screws with Silicon Gaskets and high
corrosion resistant Paint of Artlite make RL4009
no
40.0
7.5
IP65 Light Fixture with 35 watt HIT-TC lamp with integral
control gear with concrete base for 4 beams equivalent to
Artlite make RL4133 / RL 4134
no
10.0
7.2
7.3
Signature and stamp of Bidder
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
Electrical Work BOQ : 20 of 27
DESCRIPTION
UNIT
7.6
IP65 wall mounted UP & Down Lighter with 70 watt CDMT integral Light fixture made from die cast aluminium with
anti glare baffles with one piece high purity reflector &
durable silicon rubber, Clear toughned glass and
corossion restant paint of Philips make Cat. no. DCP 721
/ CDMT 70 watt
no
10.0
7.7
IP65 wall mounted Down Lighter with 70 watt CDM-T
integral Light fixture made from die cast aluminium with
anti glare baffles with one piece high purity reflector &
durable silicon rubber, Clear toughned glass and
corossion restant paint of Philips make Cat. no. DCP 731
/ CDMT 70 watt
no
70.0
7.8
IP 65 Post top Lanetrn Fitting with 150 watt Master Colour
CDM-T with Integral Electronic control Gear with
presmatic diffuser with louvers with Optical cover
Transparent polycarbonate bowl and cover with high
pressure die cast alluminium housing with extruded
alluminium
disc
supported
roads
with
polymethylmethacrylicimide refractor & diffusers with
acrylonitrilbutadienestyrene horizontal reflective disk of
Philips make Malmo CDS 550 / 150 watt CDM-T
no
200.0
7.9
Decorative Indirect post top luminaire IP 65 Post top
lantern fitting Suitable for CDM-T 150W Master Colour
CDM-T with Integral Electronic control Gear with housing
made from die cast alluminium with high finish extruded
aluminium column of 4 mtr with base flange.extruded
aluminium pole also provided along with post top
Corrosion resistant powder paint with chemical protection
Remote integral control gear of Philips make Regina CPP
735 - 1 x 150 watt CDM-T lamp with pole
no
40.0
1) 8 way connector and 6A MCB
2) 50 mm diameter DWC pipe for each cable entry. Pipe
length is up to 3.5 mtr. Per cable
3) Wiring up to the light fixture from the junction box
using 3nos x 1.5 sq.mm. flexible copper wires / Fixture of
specified make.
4) 1 mtr deep M 20 grade Concrete coping with base plate
with stiffner with anchor bolts.
Signature and stamp of Bidder
QTY
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
DESCRIPTION
Electrical Work BOQ : 21 of 27
UNIT
QTY
5) Sprial/Coil Type Earthing from the 8 swg Cu. Wire of
2.5 mtr. With the suitable size pipe with clamps and
painting.
6) Radium stip of two colour at suitable height
7) Excavation & back filling for erection of poles. Debris to
be removed from the site to suitable location as per the
instruction of the engineer incharge
7.10 IP 65 Light Column of 14 feet height with 4 feet light
section made of Clear acrylic, elliptical lens with a satin
finish and internal flute. Mechanically assembled to the
housing & 10 feet of pole shaft made of Made from 7"
(178 mm) wide by 5" (127 mm) deep, elliptical, extruded
(6061-T6) aluminum tubing, having a 0.250" (6.4 mm) wall
thickness, welded to both the bottom and top of the
anchor plate with 70 watt CDM - R Lamp with ballast of
High power factor of 90% with Lamp starting capacity of 20˚F (-30˚C). Assembled on a unitized removable tray
withquick disconnect plug with Housing made from an
elliptical die cast (356) aluminum frame of 7" (178 mm)
wide by 5" (127 mm) deep having a 0.188" (4.7 mm)
equivalent to Philips ( Lumec ) make Light Column OV 2
1) 8 way connector and 6A MCB
2) 50 mm diameter DWC pipe for each cable entry. Pipe
length is up to 3.5 mtr. Per cable
3) Wiring up to the light fixture from the junction box
using 3nos x 1.5 sq.mm. flexible copper wires / Fixture of
specified make.
4) 1 mtr deep M 20 grade Concrete coping with base plate
with stiffner with anchor bolts.
5) Sprial/Coil Type Earthing from the 8 swg Cu. Wire of
2.5 mtr. With the suitable size pipe with clamps and
painting.
6) Radium stip of two colour at suitable height
7) Excavation & back filling for erection of poles. Debris to
be removed from the site to suitable location as per the
instruction of the engineer incharge
Signature and stamp of Bidder
no
10.0
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
DESCRIPTION
Electrical Work BOQ : 22 of 27
UNIT
QTY
7.11 Supply, installation, testing and commisioning of
Decorative lantern IP 66-Top cover is made of die cast
aluminium,plug cover made of die cast aluminium with
two captive screws fitted with a reflector anodised
aluminium,upper reflector made up of chemically polished
spun aluminium attached to the cover of the luminaire.,
Lower reflector made of chemically polished spun
aluminium.Base and arms made up of die cast
aluminium,protector made up of injection moulded
polycarbonate having impact resistance of IK O8.The
luminaire is suitable for 150 watt MH or CDMT
lamp.Integral fixtures with lamp and control gear &
complete to be fixed on the street light poles should be of
top mounting type with toughened glass complete in all
respect equivalent to Schreder make ALURA/STRIATED
METHACRYLATE/1577/CDM-T/150
no
5.0
7.12 Supply, installation, testing and commisioning of IP-66
luminaire consisting of two parts made of painted, die cast
Aluminium alloy. The body contains a reflector made of
polished and anodised Aluminium and a removable
control gear plate. The protector is made of hardened
glass having impact resistance of glass IK 08. It is sealed
to the cover with a silicone gasket. It is suitable for 250W
HPSV Lamp . complete in all respect with the Control
Gear, Lamp & other Accessories integral type equivalent
to Schreder make NEOS 3 / IB / 250/ 1709. with Son T +
PIA / MH lamp
no
5.0
7.13 IP65 flood light luminaire with integral control gear with
250 watt Metal Helide lamps & Control gear of Philips
make MWF 331 / 250 watt SK / AK
no
90.0
Signature and stamp of Bidder
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
DESCRIPTION
7.14 SITC of Kesselec Schreder make : Cat. Ref. N. Trapez
Pole ( 9 mtr. G. I. ) with 4 arm Bracket with 4 nos. of
PQ3S fitting :
comprising of 9 mtr. Pole with 4 arm. Bracket pole with 4
nos. of fitting with 140 watt Cosmo polis Lamp & control
gear complete in all respect from specified approved
make
Luminaries shall be IP66 SEAL SAFE, comprised of an
aluminium body and thermally tempered glass protector.
The optical compartment is comprised of a deep drawn,
polished and anodised reflector. The luminaries is with 8
mt decorative pole & Four arm bracket of 1000 mm on
each side & have provision for the bunting. The pole &
brackets are painted with MRF PU paint .Luminaries is
suitable for cosmopolis lamp of 150 watt with lamp.
Electrical Work BOQ : 23 of 27
UNIT
QTY
no
2.0
no
12.0
1) 8 way connector and 6A MCB
2) 50 mm diameter GI pipe for each cable entry. Pipe
length is up to 3.5 mtr. Per cable
3) Wiring up to the light fixture from the junction box
using 3nos x 1.5 sq.mm. flexible copper wires / Fixture of
specified make.
4) Concrete coping of 1.5 mtr. with 1 mtr. Long foundation
bolt with base plate with stiffener as per drawing.
5) Spiral/Coil Type Earthing Wire of 2.5 mtr. With the
suitable size pipe with clamps and painting.
6) Radium strip of two color at suitable height
7) Excavation & back filling for erection of poles. Debris to
be removed from the site to suitable location as per the
instruction of the engineer in charge
7.15 SITC of Kesselec Schreder make Cat. No. FTR 390 / 1 x
55 watt T5- R lamp with lamp control gear ^ all hanging
accessories
Signature and stamp of Bidder
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
DESCRIPTION
Electrical Work BOQ : 24 of 27
UNIT
QTY
7.16 Supplying,
erecting,
connecting,
testing
and
commissioning of following type Street Light Fixture with
all necessary Hadware, Internal Wiring with Lamp, Ballast
etc. all required accessories Complete in all respect.
7.16.1 Any kind of Light Fixtures type - A (with Basic Rate of
Rs.8000/-)
7.16.2 Any kind of Light Fixtures type - B ( with Basic Rate of
Rs.15000/-)
7.16.3 Any kind of Light Fixtures type - C ( with Basic Rate of
Rs.30000/-)
7.16.4 Any kind of Light Fixtures type - D ( with Basic Rate of
Rs.50000/-)
7.16.5 Any kind of Light Fixtures type - E ( with Basic Rate of
Rs.100000/-)
7.16.6 Any kind of Light Fixtures type - F ( with Basic Rate of
Rs.200000/-)
7.17 Supply, installation, testing and commissioning of Fans (
Energy saving ) without fan regulator.
7.17.1 36" dia sweep high speed high breeze ceiling fans white
in colour.
7.17.2 48" dia sweep high speed high breeze ceiling fans white
in colour.
7.17.3 Additional fan rod made out of 10 guage painted GI pipe
with all required accessories for fan suspention.
no
250.0
no
100.0
no
75.0
no
10.0
no
10.0
no
5.0
no
5.0
no
45.0
rmt
10.0
no
20.0
7.18 Exhaust Fans :
7.18.1 SITC of light duty 225 mm. diameter propeller exhaust
fans with louvers
Sub Total 7.....
Signature and stamp of Bidder
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
DESCRIPTION
8.0
8.1
Earthing
Supplying & erecting funnel type earthing having earth
plate of following size buried in specifically prepared
earth pit 3 mtr. below ground with 40 kg. charcoal and salt
with alternate layers of charcoal & salt, 20mm.dia. G.I.
pipe with Funnel with a wire mesh for watering & bricks
masonry block, C.I. Cover complete as per para 7.3 of IS
3043 with necessary length of double G.I. / copper earth
Strip of the 25 x 3 mm bolted with Brass Screw to the
plate 3 mtr long complete connected to the nearest switch
gear with end socket as per direction & duly tested by
earth tester confirming to ISS (As per drawing) with
following specification, with Excavation, Back Filling,
Making the Chamber & Chamber cover complete in all
respect.
8.2
Chemical Type Earthing ( Ashlok or equivalent )
Supplying & erecting in earth pit of minimum bore dia.
225mm size , approved make Safe Earthing Electrode
consisting Pipe-in-Pipe Technology as per IS 3043-1987
made of corrosion free G.I.Pipes having Outer pipe dia
of 50mm having 80-200 Micron galvanising, Inner pipe dia
of 40 mm having 200-250 Micron galvanising, connection
terminal dia of
14 mm with constant ohmic value
surrounded by highly conductive compound with high
charge dissipation suitable for following type of
applications.
Electrical Work BOQ : 25 of 27
UNIT
QTY
(a) For Electrical installation up to 11 KV
located in
other than normal soil i.e.
Soft Rock, Marshy Soil etc.
-Length of Pipe : 2000 mm
-Back filling Compound :1 no. Bag of 25 Kg.
Signature and stamp of Bidder
no
15.0
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
8.3
DESCRIPTION
Electrical Work BOQ : 26 of 27
UNIT
QTY
Earth wire/strips :
Supply and laying required size Cu/GI. earthing strips for
interconnecting the earthing stations, panels, section pillar
etc. in built up trenches, on walls/ceiling, buried in ground
generally as specified and shown on drawings complete
with :
8.3.1
8.3.2
8.3.3
8.3.4
9.0
9.1
9.2
9.3
9.4
9.5
a) Fixing accessories.
b) Corrosion protection of buried conductors with
bituminous coating and covered with PVC tapes.
25 x 3 mm cu. strip
25 x 3 mm GI. strip
No.8 gauge bare cu. earth wire
No.16 gauge bare GI. earth wire
Sub Total 8.....
P. A. System
SITC of DVD player of Philips make DVP 3336/94
SITC of IP 65 wall mounting / Pole Mounting speaker with
5W rated input power 3.3 K. Ohms / 3W impedance, 100 10000 Hz frequency response with 6 inch dia. cone type 8
ohms speakers duly fitted in ABS plastic cabinet of color
match with wall or ceiling of following size and as directed
by engineer in charge (Philips / Bosch make)
mtr
mtr
mtr
mtr
100.0
1,000.0
600.0
20,000.0
no
no
1.0
200.0
SITC OF microphone with press to call switch for Public
address system, (Philips / Bosch make)
SITC of local volume control -cum ON-OFF switch with
flush mounting metal boxes, mounting plate matching with
electrical switches (Same make as switch)
no
5.0
no
5.0
Supplying & Laying of 2 Core X 1sq.mm Shielded wire in
PVC Pipe With all accessories. ( For Speaker wiring)
mtr
6,000.0
Signature and stamp of Bidder
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT
Sabarmati River Front Development Corporation Limited
SR.
NO.
Electrical Work BOQ : 27 of 27
DESCRIPTION
UNIT
QTY
9.6
SITC of power Audio amplifiers including all
necessary control desk and microprocessor based
control unit with microphone, BGM, Call Station &
PC input including providing necessary rack for
mounting the Amplifier (with Rack ). Suitable to
connect 200 Speakers (Philips / Bosch / Ahuja
make)
no
1.0
9.7
SITC of 4 zone Switcher
no
1.0
No
No
No
Kg
5.0
5.0
10.0
3,000.0
Sub Total 9.....
10.0 Miscellaneous
10.1 Liason / Follow UP with Supply Co.
Filling the necessary application to supply co. following up
and getting the supply filling the necessary test report to
the supply co. inclusive. All official fees including security
deposits will be paid by the client and out of pocket
expenses shall be of contractor.
10.1.1
10.1.2
10.1.3
10.2
up to 10 KW
FOR 10 to 20 KW
More than 20 KW
Providing , erecting , fabricating the M.S. structure as per
requirement on site incorporating proper size of M.S.
angles, flats, bars, channels, pipes, sections, Sheets & for
the pole swaging with the suitable dia pipe complete with
cutting, welding, grinding & finishing duly painted with two
coat of red oxide & 1 coat of P.U. Paint with erection on
site as per direction of engineer in charge with necessary
grouting, cementing, plastering & finishing complete as
per the instruction of the engineer in charge.
Sub Total 10.....
Signature and stamp of Bidder
RATE
SUPPLY
ITC
TOTAL
TOTAL RATE IN WORDS
AMOUNT