Philips Lumec
Dimmable luminaire specification
document for un-approved
0-10V and DALI control device,
integrated by other.
Martin Mercier Eng.
New Products Engineering
Document revision table
Description
Modified by
Date
Status
Dimmable driver output vs 0-10V input graph
added
Martin Mercier
2010/06/27
Publish
Minimum dimming level added
Martin Mercier
2010/07/22
Publish REV 3
Max current to be sink added on drawing figure2
Martin Mercier
2010/11/08
Publish REV 5
DALI added, LED removed (for HID dimming)
Martin Mercier
2011/09/27
Publish REV 5
Table of content
0-10V wiring diagram
0-10V functionality schematic
DALI wiring diagram
DALI functionality schematic
Mechanical specification
Control wiring:
Power wiring:
Electrical specification
Control device output:
Control device input:
Minimum diming level:
Electrical specification
Dimmable driver output vs 0-10V input:
Philips Lumec Certification
Philips Lumec Warranty
0-10V wiring diagram
Figure 1 - Wiring diagram
0-10V functionality schematic
Figure 2 - Functionality schematic
The 0-10V input on the LED driver or ballast is an active and passive control circuit. The light level can be
determined by a passive current sinking device, like a potentiometer. The resistor value will change the current
in the 0-10V loop and change the driver current output. It can also be determined by an active voltage source,
as long as it is a current sinking output device.
The maximum light output will be delivered at 10V (+/- 0.5). The minimum light output will be delivered at 1V
(+/- 0.5). If 0-10V wires are shorted by a mechanical switch or by a short in the wiring, the driver will operate at
minimum light level. If the connection between 0-10V is open, the driver will operate at maximum light level.
DALI wiring diagram
DALI functionality schematic
Mechanical specification
All wiring related to the un-approved 0-10V / DALI control device has to be in accordance with these
specifications:
Control wiring:
Type:
Multi or mono.
Gauge:
22 AWG or smaller gauge.
Temperature:
105C minimum
Rated voltage:
NA
Certification:
UL/CSA certified
Color:
0-10V: It is recommended that the wires colors respect the driver 0-10V wires
colors. The Philips Lumec 0-10V are provided as follows:
Positive +: Purple
Negative –: Gray
DALI: There is not particular recommendation for the DALI wiring. The Philips
Lumec DALI wires are provided as follow:
DALI 1: Purple
DALI 2: Purple with white stripes.
Power wiring:
Type:
Multi or mono.
Gauge:
18 AWG or smaller gauge.
Temperature:
105C minimum
Rated voltage:
600V
Certification:
UL/CSA certified
Color:
It is mandatory that the un-approved 0-10V / DALI device wires colors respect the
national electrical code and Philips Lumec wiring. Philips Lumec luminaire power
supply wires are provided as follows:
!
Live wire:
Black
Neutral wire:
White
Ground wire:
Green
Electrical specification
All electrical parameters related to the un-approved 0-10V / DALI control device have to be in accordance with
these specifications:
Control device output:
Output has to be electrically isolated from the main input.
0-10V:
Max constant voltage:
11 VDC
Min constant voltage:
0 VDC
Short term max voltage:
14 VDC
Max ripple voltage:
Not more than 10% of the average dc voltage for low or high frequency ripples.
DALI:
Max constant voltage:
22.5 VDC
Min constant voltage:
-6.5 VDC
Short term max voltage:
25 VDC
Control device input:
Surge protection:
The device as to be protected against surge event on the main AC line up to 2KV.
Minimum diming level:
The lifetime and performance of the lamp driven under a certain level by a dimmable driver or ballast cannot be
predicted. Please contact Philips Lumec to get more information on the minimum light engine dimming level
suitable for your Philips Lumec products.
"
Electrical specification
Dimmable driver output vs 0-10V input:
Figure 3 - Philips Lumec dimmable LED driver output
#
Philips Lumec Certification
Since Philips Lumec luminaires are certified only with approved 0-10V / DALI control devices, adding an
unapproved component inside the luminaire will void the certification.
If unapproved control devices are to be connected to Philips Lumec luminaires, such components must be
installed outside of the luminaire, as the integrity of the luminaire must not be altered. Access to the inside of
the luminaire shall be limited to qualified electricians and for wiring termination only. Any other modification
may void the warranty offered by Philips Lumec and may require a field evaluation by third party certification
bodies.
Philips Lumec luminaires are certified under the assumption their integrity has not been altered.
$
Philips Lumec Warranty
Philips Lumec warranty for a dimmable luminaire controlled by un-approved 0-10V / DALI device will be
honored only if the following requirements are completed with success in the time frame agreed with Philips
Lumec.
1- All un-approved 0-10V / DALI control device specifications requested by Philips Lumec have
been provided in a reasonable period of time to Philips Lumec.
2- All equipments requested by Philips Lumec related to the un-approved 0-10V / DALI control
device have been provided to Philips Lumec in the time frame agreed between all parties
involved. This procedure is mandatory for a control device to be inserted inside any Philips
Lumec luminaire and may be requested outside integration. All samples provided to Philips
Lumec have to be accurate samples corresponding to the device that will be installed in
luminaire.
3- Any other component added after reception of the luminaire by the client has to be installed
and operated in accordance with the current version of the National Electric Code and such
components must be installed outside of the luminaire, as the integrity of the luminaire must
not be altered.
4- Dimming level has to be performed in accordance with lamp specification publish by the
lamp manufacturer. Philips Lumec LEDs lamp minimum dimming current is 100mA per
LEDs. Please contact Philips Lumec to get more information on the minimum light engine
dimming level suitable for your Philips Lumec products.
5- The luminaire has to be set by default at 100% light output (maximum luminaire wattage) if
the un-approved 0-10V / DALI control device enter in those situation:
a. fails or stops working
b. is unplugged
c. is removed
Philips Lumec luminaires are warranted under the assumption their integrity has not been
altered. All Philips Lumec warranty will be void if any of the recommendations specified in this
document have been dismissed.